OPERATION AND PARTS MANUAL Plate Compactor Model MVC-40G (Robin EH09-2D Gasoline Engine) Revision #4 (06/06/07) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. To find the latest revision of this publication, visit our website at: www.multiquip.com
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
OPERATION AND PARTS MANUAL
Plate Compactor Model
MVC-40G(Robin EH09-2D Gasoline Engine)
Revision #4 (06/06/07)
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
To find the latest revision of thispublication, visit our website at:
Ordering parts has never been easier!Choose from three easy options:
WE ACCEPT ALL MAJOR CREDIT CARDS!
When ordering parts, please supply:❒❒❒❒❒ Dealer Account Number
❒❒❒❒❒ Dealer Name and Address
❒❒❒❒❒ Shipping Address (if different than billing address)
❒❒❒❒❒ Return Fax Number❒❒❒❒❒ Applicable Model Number
❒❒❒❒❒ Quantity, Part Number and Description of Each Part
❒❒❒❒❒ Specify Preferred Method of Shipment:✓ Fed Ex/UPS ✓ DHL
■ Priority One ✓ Truck■ Ground■ Next Day■ Second/Third Day
Unless otherwise indicated by customer, all orders are treated as Standard Orders and will shipwithin 24 hours. We will make every effort to ship Air Shipments the same day the order is received,if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
If you have an MQ Account, to obtain aUsername and Password, E-mail us at:[email protected].
To obtain an MQ Account, contact yourDistrict Sales Manager for more information.
Order via Internet (Dealers Only):Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams■ Order Parts■ Print Specification Information
Note: Discounts Are Subject To Change
Goto www.multiquip.com and click on
Order Parts to log in and save!
Use the internet and qualify for a 5% Discounton Standard orders for all orders which includecomplete part numbers.*
Order via Fax (Dealers Only):All customers are welcome to order parts via Fax.Domestic (US) Customers dial:1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 3% Discounton Standard orders for all orders which includecomplete part numbers.*
Order via Phone: Domestic (US) Dealers Call:1-800-427-1244
Best Deal!
International Customers should contacttheir local Multiquip Representatives forParts Ordering information.
Non-Dealer Customers:Contact your local Multiquip Dealer forparts or call 800-427-1244 for help inlocating a dealer near you.
Lethal Exhaust GasesSafety precautions should be followed at all times when operatingthis equipment. Failure to read and understand the SafetyMessages and Operating Instructions could result in injury toyourself and others.
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
This Owner's Manual has beendeveloped to provide completeinstructions for the safe and efficientoperation of the MQ Model MVC-40G Plate Compactor. Refer to theengine manufacturers instructionsfor data relative to its safe operation.
Before using this plate compactor, ensure that the operatingindividual has read and understands all instructions in thismanual.
NOTE
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will informyou about potential hazards that could injure you or others.The Safety Messages specifically address the level ofexposure to the operator, and are preceded by one ofthree words: DANGER, WARNING, or CAUTION.
HAZARD SYMBOLS
Potential hazards associated with the operation of the MQModel MVC-40G Plate Compactor. will be referenced withHazard Symbols which appear throughout this manual, andwill be referenced in conjunction with Safety Message AlertSymbols.
ALWAYS wear approved respiratoryprotection when required.
WARNING - Respiratory Hazards
Engine exhaust gases containpoisonous carbon monoxide. This gasis colorless and odorless, and cancause death if inhaled. NEVER operatethis equipment in a confined area orenclosed structure that does not provide ample free flowair.
WARNING - Lethal Exhaust Gas Hazards
Gasoline is extremely flammable, andits vapors can cause an explosion ifignited. DO NOT start the engine nearspilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running orhot. DO NOT overfill tank, since spilled fuel could ignite ifit comes into contact with hot engine parts or sparks fromthe ignition system. Store fuel in approved containers, in
DANGER - Explosive Fuel Hazards
Engine components can generate extremeheat. To prevent burns, DO NOT touchthese areas while the engine is running orimmediately after operations. Neveroperate the engine with heat shields or heatguards removed.
WARNING - Burn Hazards
You WILL be KILLED or SERIOUSLY injured if you DONOT follow directions.
DANGERDANGERDANGERDANGERDANGER
You CAN be KILLED or SERIOUSLY injured if you DONOT follow directions.
WARNINGWARNINGWARNINGWARNINGWARNING
You CAN be INJURED if you DO NOT follow directions.
Other important messages are provided throughout thismanual to help prevent damage to your light tower, otherproperty, or the surrounding environment.
CAUTION - Equipment Damage Hazards
ALWAYS wear approved eye andhearing protection.
CAUTION - Eye and Hearing Hazards
ALWAYS place the power source, circuitbreakers or ON/OFF switch in the OFFposition, when the generator is not in use,unless connected to transfer switch.
CAUTION - Accidental Starting Hazards
NEVER operate equipment with covers,or guards removed. Keep fingers, hands,hair and clothing away from all movingparts to prevent injury.
CAUTION - Rotating Parts Hazards
Before attempting to operatethe plate compactor, and toavoid serious injury topersonnel, always read andunderstand operation manual.Failure to read and understandoperation manual couldresult in serious harm or evendeath!
WARNING - Read Manual
DO NOT refuel plate copmpactor if compactor is placedinside truck bed with PLASTIC LINER. Possibility existsof explosion or fire due to static electricity.
The following safety guidelines should always be used whenoperating the MQ Mikasa Model MVC-40G Plate Compactor.
GENERAL SAFETY
■ DO NOT operate or service this equipment before readingthis entire manual.
■ This equipment should not be operated by persons under18 years of age.
■ NEVER operate this equipment without proper protectiveclothing, shatterproof glasses, steel-toed boots and otherprotective devices required by the job.
■ High Temperatures – Allow theengine to cool before adding fuel orperforming service and maintenance functions. Contactwith hot! components can cause serious burns.
■ The engine section of this mixer requires an adequatefree flow of cooling air. NEVER operate the compactorin any enclosed or narrowarea where free flow of theair is restricted. If the airflow is restricted it willcause serious damage tothe compactor or engineand may cause injury topeople. Remember theplate compactor's engine gives off DEADLY carbonmonoxide gas.
■ NEVER operate this equipment under theinfluence of drugs or alcohol.
■ NEVER touch the hot exhaustmanifold, muffler or cylinder. Allowthese parts to cool before servicingengine or mixer.
■ NEVER operate this equipment when notfeeling well due to fatigue, llness or takingmedicine.
■ Topping-off to filler port is dangerous, as it tends to spillfuel.
■ Maintain this equipment in a safe operating condition atall times.
■ ALWAYS store equipment properly when it is not being used.Equipment should be stored in a clean, dry location out of thereach of children.
■ NEVER operate the plate compactor inan explosive atmosphere or nearcombustible materials. An explosion orfire could result causing severe bodilyharm or even death.
■ ALWAYS refuel in a well-ventilated area, away from sparksand open flames.
■ ALWAYS use extreme caution whenworking with flammable liquids. Whenrefueling, stop the engine and allow it tocool. DO NOT smoke around or near themachine. Fire or explosion could resultfrom fuel vapors, or if fuel is spilled on ahot engine.
■ ALWAYS wear proper respiratory (mask),hearing and eye protection equipment whenoperating the plate compactor.
■ Whenever necessary, replace nameplate, operation andsafety decals when they become difficult read.
■ Manufacture does not assume responsibility for anyaccident due to equipment modifications.
■ NEVER use accessories or attachments, which are notrecommended by Multiquip for this equipment. Damageto the equipment and/or injury to user may result.
Failure to follow instructions in thismanual may lead to serious injury oreven death! This equipment is to beoperated by trained and qualifiedpersonnel only! This equipment is forindustrial use only.
■ ALWAYS shutdown engine before transporting.■ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.■ Drain fuel when transporting compactor over long
distances or bad roads.
MAINTENANCE
■ NEVER lubricate components or attempt service on arunning compactor.
■ ALWAYS allow the plate compactor a proper amount oftime to cool before servicing.
■ Keep the compactor in proper running condition.■ Fix damage to the plate compactor immediately and
always replace broken parts.■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel andfuel filters.
■ DO NOT use food or plastic containers to dispose ofhazardous waste.
EMERGENCIES
■ ALWAYS know the location of the nearest fireextinguisher and first aid kit.
■ In emergencies always know the location of thenearest phone or keep a phone on the job site.Also know the phone numbers of the nearestambulance, doctor and fire department. Thisinformation will be invaluable in the case of anemergency.
■ NEVER run engine without air filter. Severe engine damagemay occur.
■ ALWAYS service air cleaner frequently to prevent carburetormalfunction.
■ ALWAYS be sure the operator is familiar with proper safetyprecautions and operations techniques before usingcompactor.
■ ALWAYS read, understand, and follow procedures inOperator’s Manual before attempting to operate equipment.
■ Refer to the ROBIN Engine Owner's Manual for enginetechnical questions or information.
Loading and Unloading (Crane)■ Before lifting, make sure that machine parts (lifting bale and
vibration insulator) are not damaged and screws are notloosened or lost.
■ ALWAYS make sure crane or lifting device has been properlysecured to the lifting bale on the compactor.
■ NEVER lift the compactor while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient strength.
■ Use one point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath themachine while lifting.
■ Try not to lift compactor to unnecessary heights.
The Mikasa MVC-40G is a one direction (forward) walk behind,plate compactor designed for the compaction of sand, mixedsoils and asphalt. This plate compactor is a powerful compactingtool capable of applying a tremendous force in consecutive highfrequency vibrations to a soil surface. Its applications includecompacting for road, embankments and reservoirs as well asbackfilling for gas pipelines, water pipelines and cable installationwork.
The MVC-40G is small and lightweight. It can be easily handledby one person in confined areas. It has an accessible front-mounted vibrator assembly. The sealed belt cover keeps dirtand rocks away from the belt.
Vibratory Plate
The vibratory plate of the compactor produces low amplitudehigh frequency vibrations, designed to compact granular soilsand asphalt.
The resulting vibrations cause forward motion. The engine andhandle are vibration isolated from the vibrating plate.
Frequency/Speed
The compactor's vibrating plate has a frequency of 6,200 vpm(vibrations per minute). The travel speed of the compactor isapproximately 82 ft./minute (25 meters/minute).
Engine
The MQ Mikasa MVC-40G Plate Compactor is equipped with aair-cooled, 4-stroke ROBIN EH09-2D gasoline engine. Whenadding fuel, always use unleaded gasoline.
Controls
Before starting the MVC-40G Plate Compactor identify andunderstand the function of the controls and components asindicated Figure 3.
Figure 3 shows the location of the components and generalmaintenance parts. The function of each component is describedbelow:
1. Hand Lift Handle – When lifting of the compactor bypersonnel is required, use this hand lift handle. DO NOTattach a crane or heavy lifting device to this handle to liftthe compactor.
2. Lifting Bale – When lifting of the compactor is requiredeither by forklift, crane etc., tie rope or chain around thislifting point.
3. Handle Bar – When operating the compactor use thishandle bar to maneuver the compactor.
4. Belt Cover – Remove this cover to gain acess to the V-belts. NEVER run the compactor without the V-belt cover. Ifthe V-belt cover is not installed, the possibility exist thatyour hand may get caught between the V-belt and clutch,thus causing serious injury and bodily harm.
5. Vibrating Plate – A flat, open plate made of durable castiron construction used in the compacting of soil.
6. Vibration Case – Encloses the eccentric, gears andcounter weights.
7. Gasoline Engine – This plate compactor uses a 4-stroke,air cooled ROBIN EH09-2D gasoline engine. Refer to theROBIN owner's manual for engine information.
Figure 4. Engine Controls and ComponentsINITIAL SERVICING
The engine (Figure 4) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the ROBIN engine servicemanual for instructions and details for proper operation and servicing.
9. Carburetor – Regulates fuel flow.
10. Oil Dipstick/ Filler Cap– Remove the filler cap dipstickwhen checking the engine oil level. Add engine oil throughthis filler port. See Table 4 for recommended type engineoil.
11. Oil Drain Plug – Remove this plug to drain engine oil fromthe crankcase.
12. Muffler – Used to reduce noise and emissions. ALWAYSallow a sufficient amount of time for the muffler to cool beforetouching.
Operating the engine without an airfilter, with a damaged air filter, or afilter in need of replacement willallow dirt to enter the engine,causing rapid engine wear.
NOTE
1. Throttle Lever – Used to adjust engine RPM. Push leverupwards for SLOW, and down for FAST.
2. Recoil Starter (pull rope) – Manual-starting method. Pullthe starter grip until resistance is felt, then pull briskly andsmoothly
3. Air Cleaner – Prevents dirt and other debris from enteringthe fuel system. Release clips on side of air filter cannisterto gain access to filter element.
4. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stopthe flow of fuel.
5. Choke Lever – Used in the starting of a cold engine, or incold weather conditions. The choke enriches the fuelmixture.
6. Fuel Tank – Holds .40 gals (1.5 liters)unleaded gasoline.For additional information refer to ROBIN engine owner'smanual.
7. Fuel Filler Cap – Remove this cap to add unleadedgasoline to the fuel tank. Make sure cap is tightenedsecurely. DO NOT over fill.
8. Start/Stop Switch – Place this switch in the "ON" position(1) to start the engine. Place in the "OFF" position (0) tostop the engine.
Engine components can generate extreme heat.To prevent burns, DO NOT touch these areaswhile the engine is running or immediately afteroperating. NEVER operate the engine with themuffler removed.
Warning - Hot Surface
13. Spark Plug – Provides spark to the ignition system. Setspark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch)Clean spark plug once a week.
1. Read safety instructions at the beginning of manual.
2. Clean the compactor, removing dirt and dust. Particularly, thebottom of the plate, engine cooling air inlet, carburetor andair cleaner.
3. Check the air filter for dirt and dust. If the air filter is dirty, blowthrough the air filter cartridge from the inside, moving a jet ofdry compressed air up and down until all dust is removed.Otherwise replace air filter with a new one.
4. Check carburetor for external dirt and dust. Clean with drycompressed air.
5. Check fastening nuts and bolts for tightness. Loosenedscrews or bolts due to vibration, could lead to unexpectedaccident.
Engine Oil Check
1. To check the engine oil level, place the plate compactor onsecure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler hole(Figure 5) and wipe it clean.
Figure 5. Engine Oil Dipstick
3. Insert and remove the dipstick without screwing it into the fillerneck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 6), fill to the edge of the oil fillerhole with the recommended oil type (Table 4).
Figure 6. Engine Oil Dipstick
The Oil Aler t system willautomatically shut-down theengine if the engine oil level fallsbelow safe operating limits.Always be sure to check theengine oil level prior to startingthe engine.
UPPER LIMIT
LOWER LIMIT
NOTE
Fuel Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low,replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DONOT top-off fuel. Wipe up any spilled fuel.
Motor fuels are highly flammable and canbe dangerous if mishandled. DO NOTsmoke while refueling. DO NOT attempt torefuel the compactor if the engine is hot! ,running or in the dark.
Danger - Flammable Fuel
Adding fuel to the tank should be done onlywhen the engine is stopped and has had anopportunity to cool down. In the event of a fuelspill, DO NOT attempt to start the engine untilthe fuel residue has been completely wipedup, and the area surrounding the engine isdry.
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm(Figure 9) when depressed with finger at midway betweenthe clutch and vibration pulley shafts.
MVC-40G — INSPECTION
CLUTCH
PULLEY
VIBRATOR
PULLEY
Figure 7. V-Belt Hazard
1. To check the V-belt tension, remove the bolts that securethe belt cover to the frame as shown in Figure 8.
Figure 8. V-Belt Cover Removal
3. A loose V-belt will decrease the power transmission output,causing reduced compaction and premature wear of thebelt.
4. If the V-belt becomes worn or loose, replace it .
Figure 9. V-Belt Tension
Vibrator Oil Check
1. Place the MVC-40Gplate compactor horizontally on a flatsurface. Make sure the compactor is level when checking theoil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)as shown in Figure 10. The oil level should be up to the oil plug.If oil is required, replace using only SAE 10W-30 motor oil.
NEVER attempt to check the V-belt with the engine running.Severe injury can occur if your hand (Figure 7) gets caughtbetween the V-belt and the clutch. Always use safety gloves.
1. Place the engine fuel valve lever (Figure 11) in the "ON"position.
Figure 11. Engine Fuel Valve Lever (ON Position)
4. Place the throttle lever (Figure 14) in the slow position(idle)
Figure 13. Engine Choke Lever (Closed)
2. Place the engine ON/OFF switch (Figure 12) in the "ON "position.
This section is intended to assist the operator with the initialstart-up of the plate compactor. It is extremely important thatthis section be read carefully before attempting to use thecompactor in the field.
DO NOT attempt to operate the plate compactoruntil the Safety, General Information andInspection sections of this manual have beenread and thoroughly understood.
Caution - Read Manual
Figure 15. Starter Grip
5. Grasp the starter grip (Figure 15) and slowly pull it out. Theresistance becomes the hardest at a certain position, corre-sponding to the compression point. Pull the starter grip brisklyand smoothly for starting.
Figure 14. Throttle Lever (Slow)
3. Place the choke lever (Figure 13) in the "CLOSED " positionif starting a cold engine, if starting a warm engine or thetemperature is warm, place the choke lever in the "OPEN"position
6. Let the engine warm for a few minutes without a load andcheck for fuel leaks, and noises that would associate with alose component.
1. Once the engine has started, move the engine throttle leverquickly to the fast position.
2. With the throttle lever in the fast position, the engine speedshould be around 2,300 RPM, therefore engaging the cen-trifugal clutch.
Always move the throttle leverquickly without hesitation, becauseincreasing the engine speed slowlycauses the clutch to slip.
3. Firmly gasp the compactor's handle bar with both hands , thecompactor will begin moving forward.
4. Slowly walk behind the compactor and be on the lookout forany large objects or foreign matter that might cause damageto the compactor or bodily injury.
5. Compactor traveling speed may drop on soils which containclay, however there may be cases where traveling speeddrops because the compaction plate does not leave theground surface easily due to the composition of the soil. Torectify this problem do the following:
Check the bottom plate to see if clay orequivalent material has been lodged in the platemechanism. If so, wash with water and remove.
Remember the compactor does not work asefficiently on clay or soils that have a highmoisture content level.
If the soil has a high moisture level, dry soil toappropriate moisture content level or carry outcompaction twice.
NOTE
Make sure to follow all safety rules referenced in the safetysection of this manual before operating compactor. Keep workarea clear of debris and other objects that could causedamage to the compactor or bodily injury.
1. To make sure your plate compactor is always in goodworking condition before using, carry out the maintenanceinspection in accordance with Tables 5 through 7.
MVC-40G — MAINTENANCE
Check for leakage of fuel or oil.
Remove soil and clean the bottom of compaction plate.
Check engine oil, see page 15.
Check for loose screws including tightness. See Table 7below (tightening torque ), for retightening:
Daily Service
ENGINE OIL
1. Drain the engine oil when the oil is warm as shown inFigure 20.
2. Remove the oil drain bolt and sealing washer and allowthe oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listedin Table 4. Engine oil capacity is .317 quarts (.3 liters). DONOT overfill.
4. Install drain bolt with sealing washer and tighten se-curely.
Inspection and other services should always be carried outon hard and level ground with the engine shut down.
CAUTION - Inspection
These inspection intervals are for operation under normalconditions. Adjust your inspection intervals based on thenumber of hours plate compactor is in use, and particularworking conditions.
CAUTION - Inspection Intervals
CAUTION - Inspection Intervals
Fuel piping and connections should be replaced every 2years.
1. When changing the vibrator oil, remove the drain plug(Figure 10), and simply tip the compactor to drain the oil.Note that the oil will drain more easily while it is hot.Remember to use only 10W-30 motor oil when replacingvibrator oil.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover tocheck the V-belt tension. Tension is proper if the belt bendsabout 10 mm when depressed strongly with finger betweenshafts. Loose or worn V-belts reduces power transmissionefficiency, causing weak compaction and reduces the life ofthe belt itself.
Figure 20. Engine Oil (Draining)
Engine Air Cleaner
1. Remove the air cleaner cover and foam filter element asshown in Figure 21.
2. Wash the gray foam outer filter element in kerosene ordiesel fuel. Then saturate it in a mixture of 3 parts kero-sene or diesel fuel and 1 part engine oil. Completelysqueeze the element to remove the mixture and re-installit back into the air cleaner.
Figure 21. Air Cleaner
Spark Plug
1. Remove and clean the spark plug (Figure 22).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm). Thisunit has electronic ignition, which requires no adjustments.
Figure 22. Spark Plug Gap
NEVER attempt to check the V-belt with the engine running.Severe injury can occur if your hand (Figure 7) gets caughtbetween the V-belt and the clutch. Always use safety gloves.
WARNING - V-belt Hazard
Whenever the compactor's vibration becomes weak or lostduring normal operation regardless of operation hours, checkthe V-belt and clutch immediately.
CAUTION - Vibration Check
Checking Clutch
Check the clutch simultaneously with V-belt checking. With beltremoved, check outer drum of the clutch for seizure and "V"groove for wear or damage with your eyes. Clean the "V" grooveas necessary. Wear of lining or shoe should be checked withrunning check. If the shoe is worn, power transmission becomesdeficient and slipping will result.
Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to leftside of upper clutch and, in the same manner as in removal,rotate offset wrench clockwise so that the V-belt goes back on.
Replacing the V-belt
Remove the upper and lower belt covers. Engage an offsetwrench (13 mm) or the like to vibrator pulley (lower) fasteningbolt. Engage waste cloth or the like at midway of V-belt on the leftside and while pulling it back strongly, rotate the offset wrenchclockwise so that the V-belt will come off.
MVC-40G — TROUBLESHOOTING (ENGINE)Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of abreakdown, please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 8) informationshown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consultour company's business office or service plant.
MVC-40G — TROUBLESHOOTING (PLATE COMPACTOR)Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of abreakdown, please take a remedial action following the diagnosis based on the Compactor Troubleshooting (Table 9)information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it isand consult our company's business office or service plant.
The contents and part numbers listed in the parts section aresubject to change without notice. Multiquip does notguarantee the availibility of the parts listed.
NOTEWhen ordering a part that has morethan one item number listed, checkthe remarks column for help indetermining the proper part to order.
QTY. Column
Numbers Used - Item quantity can be indicated by a number,a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other partsthat are sold in bulk and cut to length.
A blank entry generally indicates that the item is not soldseparately. Other entries will be clarified in the “Remarks”Column.
REMARKS Column
Some of the most common notes found in the “Remarks”Column are listed below. Other additional notes needed todescribe the item can also be shown.
Assembly/Kit - All items on the parts list with the same uniquesymbol will be included when this item is purchased.
Indicated by:“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break - Used to list an effective serial numberrange where a particular part is used.
Indicated by:“S/N XXXXX AND BELOW”“S/N XXXX AND ABOVE”“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is usedonly with the specific model number or model number variantlisted. It can also be used to show a part is NOT used on aspecific model or model number variant.
Indicated by:“XXXXX ONLY”“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can bepurchased at any hardware shop or made out of availableitems. Examples include battery cables, shims, and certainwashers and nuts.
“Not Sold Separately” - Indicates that an item cannot bepurchased as a separate item and is either part of anassembly/kit that can be purchased, or is not available forsale through Multiquip.
The following section explains the different symbols and remarksused in the Parts section of this manual. Use the help numbersfound on the back page of the manual if there are any questions.
NO. Column
Unique Symbols - All items with same unique symbol(*, #, +, %, or >) in the number column belong to the sameassembly or kit, which is indicated by a note in the “Remarks”column.
Duplicate Item Numbers - Duplicate numbers indicatemultiple part numbers are in effect for the same general item,such as different size saw blade guards in use or a part thathas been updated on newer versions of the same machine.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part thathas not been assigned a formal part number at time ofpublication.
A blank entry generally indicates that the item is not soldseparately or is not sold by Multiquip. Other entries will beclarified in the “Remarks” Column.
Sample Parts List:NO. PART NO. PART NAME QTY. REMARKS1 12345 BOLT ....................... 1 .... INCLUDES ITEMS W/*2* WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY2* 12347 WASHER, 3/8 IN. .... 1 .... MQ-45T ONLY3 12348 HOSE .................... A/R .. MAKE LOCALLY4 12349 BEARING ................ 1 .... S/N 2345B AND ABOVE
MVC-40G— NAME PLATE AND DECALSMachine Safety Decals
The MVC-40GPlate Compactor is equipped with a number of safety decals. These decals are provided for operator safety andmaintenance information. The illustration below shows these decals as they appear on the machine. Should any of these decalsbecome unreadable, replacements can be obtained from your dealer.
NO. PART NO. PART NAME QTY. REMARKS10 2843170211 CAMSHAFT ASSY. ................................ 1 ............ INCLUDES ITEMS W/*34* 2273860123 PIN, SPRING 135* 2843640103 RELEASE LEVER 136* 0051904100 SPRING PIN 137* 0031517000 SNAP RING 138* 2743870123 RETURN SPRING 150 2743330103 TAPPET 1
ROBIN EH09-2D — AIR CLEANER ASSY.AIR CLEANER ASSY.
NO. PART NO. PART NAME QTY. REMARKS510 2843261000 AIR CLEANER ASSY. .......................... 1 .............. INCLUDES ITEMS W/*520* 2263261007 ELEMENT SET 1538* 2273590403 GASKET, 2 IN. NEW PU STD. 1570* 2263921200 NUT & WASHER ASSY. 2850 2841610103 RUBBER PIPE 1
Effective: February 22, 2006 TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shipments are F.O.B. point of origin.Multiquip’s responsibility ceases when a signedmanifest has been obtained from the carrier,and any claim for shortage or damage must besettled between the consignee and the carrier.
MINIMUM ORDER
The minimum charge for orders from Mul-tiquip is $15.00 net. Customers will be askedfor instructions regarding handling of ordersnot meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and creditwill be allowed, subject to the following provi-sions:
1. A Returned Material Authorization mustbe approved by Multiquip prior to ship-ment.
2. To obtain a Return Material Authorization,a list must be provided to Multiquip PartsSales that defines item numbers, quanti-ties, and descriptions of the items to bereturned.
a. The parts numbers and descriptionsmust match the current parts pricelist.
b. The list must be typed or computergenerated.
c. The list must state the reason(s) forthe return.
d. The list must reference the salesorder(s) or invoice(s) under which theitems were originally purchased.
e. The list must include the name andphone number of the person request-ing the RMA.
3. A copy of the Return Material Authoriza-tion must accompany the return shipment.
4. Freight is at the sender’s expense. Allparts must be returned freight prepaid toMultiquip’s designated receiving point.
5. Parts must be in new and resalable con-dition, in the original Multiquip package (ifany), and with Multiquip part numbersclearly marked.
6. The following items are not returnable:
a. Obsolete parts. (If an item is in theprice book and shows as being re-placed by another item, it is obsolete.)
b. Any parts with a limited shelf life(such as gaskets, seals, “O” rings,and other rubber parts) that were pur-chased more than six months prior tothe return date.
c. Any line item with an extended dealernet price of less than $5.00.
d. Special order items.
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
7. The sender will be notified of any materialreceived that is not acceptable.
8. Such material will be held for five workingdays from notification, pending instruc-tions. If a reply is not received within fivedays, the material will be returned to thesender at his expense.
9. Credit on returned parts will be issued atdealer net price at time of the originalpurchase, less a 15% restocking charge.
10. In cases where an item is accepted, forwhich the original purchase documentcan not be determined, the price will bebased on the list price that was effectivetwelve months prior to the RMA date.
11. Credit issued will be applied to futurepurchases only.
PRICING AND REBATES
Prices are subject to change without priornotice. Price changes are effective on a spe-cific date and all orders received on or after thatdate will be billed at the revised price. Rebatesfor price declines and added charges for priceincreases will not be made for stock on handat the time of any price change.
Multiquip reserves the right to quote and selldirect to Government agencies, and to OriginalEquipment Manufacturer accounts who useour products as integral parts of their ownproducts.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoicefor special handling including bus shipments,insured parcel post or in cases where Multiquipmust personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder fordamages in excess of the purchase price of theitem with respect to which damages areclaimed, and in no event shall Multiquip beliable for loss of profit or good will or for anyother special, consequential or incidental dam-ages.
LIMITATION OF WARRANTIES
No warranties, express or implied, are madein connection with the sale of parts or tradeaccessories nor as to any engine not manufac-tured by Multiquip. Such warranties made inconnection with the sale of new, complete unitsare made exclusively by a statement of war-ranty packaged with such units, and Multiquipneither assumes nor authorizes any person toassume for it any other obligation or liabilitywhatever in connection with the sale of itsproducts. Apart from such written statement ofwarranty, there are no warranties, express,implied or statutory, which extend beyond thedescription of the products on the face hereof.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All othertrademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-40G Plate Compactor.Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves theright to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
UNITED STATESMultiquip Corporate Office MQ Parts Department18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284Contact: [email protected] Parts Warranty Department800-306-2926 Fax: 800-672-7877 800-421-1244, Ext. 279 Fax: 310-537-1173310-537-3700 Fax: 310-637-3284 310-537-3700, Ext. 279Service Department Technial Assistance800-421-1244 Fax: 310-537-4259 800-478-1244 Fax: 310-631-5032310-537-3700