A engine, cylinder head, valves B electric, injection C gearbox, clutch, steering, oil service D springs, shock absorber, axels, silent bearings E brakes, tyres, exhaust F cooling system G body, upholstery H test and measuring equipment J fitting tools L chipping tools www.pichler-werkzeug.com
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
A engine, cylinder head, valves
B electric, injection
C gearbox, clutch, steering, oil service
D springs, shock absorber, axels, silent bearings
E brakes, tyres, exhaust
F cooling system
G body, upholstery
H test and measuring equipment
J fitting tools
L chipping tools
www.pichler-we
rkzeug.com
Austria Switzerland France Belgium
Pichler Werkzeug GmbH & Co KGPacherstrasse 20A - 6023 Innsbruck
Engine lift- and alignment equipment Carrying capacity: 900 kg Angle of inclination45° Weight: 1,7 kg Drive: 1/2" □ Load adjustable engine lifting equipment. By use of a patented unwind stand -roll coil. The alignment tool when used along with present workshop lifting equipment allows fast and safe inclining of the engine in both directions. The tool can be locked in the correct position by use of the 1/2“ security lever Engine lift- and alignment equipment p/n 608 23 00
Universal support tool for engines and sub frames A support tool recommended by Honda Switzerland particularly for use on the sub frames of Honda vehicles. This tool is also an outstanding universal auxiliary tool for all passenger vehicles, where the engine, gearbox or sub frame must be unscrewed and/or dismantled. The device has four arms which are adjustable in length and can laterally tilt. On the arms it is possible to mount guide pins or rubber plates. The support is best used with hydraulic engine and transmission jack p/n: 975 00 00.
Universal support tool for engines and subframes p/n 911 32 00
A 2
Compression test adapter D Compression test adapter diesel The adapter is mounted in place of the injector or glow plug. With a thread M 12 x 1,5 to connected to the compression writer model D p/n 609 16 00. D= injector G= glow plug Dim. measure Type 1 D M24 x 2 MB, Ford 1.8 D/TD, Opel, Peugeot, Renault 1.9/2.1 GTD, VW p/n 609 16 20 2 G M12 x 1,25 Standard PKW, BMW M51 engine, Renault R21, 25, Espace, Trafic p/n 609 16 30 3 G M18 x 1,5 older passenger cars p/n 609 16 40 4 D M24 x 2 Mazda, Mitsubishi, Nissan, Toyota B-C-H engine p/n 609 16 50 5 G M10 x 1,25 Isuzu, Mitsubishi, Nissan, Toyota L engine p/n 609 16 60 6 G M10 x 1,25 Toyota C-B-H engine p/n 609 16 70 7 D M20 x 1,5 Mitsubishi, Toyota C engine p/n 609 16 80 8 G M10 x 1 BMW engine M47/M57, Audi/VW 1.4, 1.9 and 2.5 TDI p/n 609 16 85 9 G M10 x 1 Audi, VW, Skoda, Seat 2,5l V6 TDI p/n 609 17 96 11 G M10 x 1,25 Opel Isuzu engine 1.5 D/DT, 1.7 TD p/n 602 15 20 12 D M24 x 2 Opel, not Isuzu engine 1.5 D/DT, 1.7 TD, p/n 609 17 20 13 D M22 x 1,5 VW with 1,3 engine, Polo p/n 609 17 30 15 D M24 x 2 VW 1.7, 1.9 engine, Renault 1.9TD. p/n 609 17 50 16 D M24 x 1,5 BMW, VM engine 2,5 TD, e.g.: Alfa, Ford, p/n 609 17 65 Fiat Chrysler Cherokee, Voyager, Opel Frontera, Renault Safrane 2.5 TD, Rover, Landrover, Lancia 17 D M22 x 1,5 MB from 601 / 602 / 603 with power up rating p/n 609 17 70 18 D inserted Ford Transit 2,5 TDI p/n 609 17 80
Compression tester Compression tester model O (0...25 bar) for petrol engines, with a flexible hose and an outside thread M 12x1,25, M 18x1,5 and M 14x1,25 p/n 609 10 00 compression tester model D (0...60 bar) for diesel engines, with a flexible hose and an outside thread M 14x1,25, M 18x1,5 and M 24x2 p/n 609 11 00
Compression tester Metering range model O 3-15 bar (petrol engines) model D 10-50 bar (diesel engines) Handy recording instrument with sturdy metal housing for measuring compression. With a push button switch on the hand grip and a remote start cable it is possible for one person to both start the engine and record the compression. Compression tester model O ( petrol engines) p/n 609 15 00 contents: 1 compression writer model basic unit O p/n 609 15 10 with electric push button switch in the grip 1 extension inflexible 120 mm long, p/n 609 18 00 1 extension flexible 400 mm long. p/n 609 18 20 1 replacement rubber cone sparkplug 20,8 mm p/n 609 18 40 1 replacement rubber cone sparkplug 15,9 mm p/n 609 18 70 1 remote start cable for starter operation p/n 609 18 30 100 diagram cards 3-15 bar p/n 609 18 50 Compression tester model D ( diesel engines ) p/n 609 16 00 contents: 1 Compression writer model basic unit D p/n 609 16 10 with electric push button switch in the grip 1 flexible pressure hose with valve p/n 609 19 00 1 angled coupling M 12x1,5 p/n 609 19 10 1 angled coupling M 14x1,5 p/n 609 19 20 1 diesel adapter dim.1 (injector) p/n 609 16 20 1 remote start cable for starter operation p/n 609 19 40 100 diagram cards 10-50 bar p/n 609 19 50
A 3
19 G M12 x 1,25 MB from M 601 / 602 / 603 p/n 609 17 91 20 D M22 x 1,5 MB from M 604 (four valve) p/n 609 17 90 21 G M10 x 1 Audi / VW 1,9 / 2,5 TDi 3 cyl. 1,4 TDi, PD engine p/n 609 17 92 Volvo 850, Ford Galaxy, Seat Alhambra, 22 D Ø 19/22 Grommet commercial vehicles p/n 602 17 50 23 G M10 x 1,25 Opel SOHC X 20 DTL p/n 609 17 25 24 G M10 x 1 Opel SOHC X 20 DTL / DTH from `98 100 PS p/n 609 17 27 25 G M10 x 1 MB M 611, 612, 613 CDi engines p/n 609 17 75 26 G M10 x 1 Peugeot u. Citroen with HDi engine p/n 609 17 85 27 D inserted Citroen HDI p/n 609 17 87 31 G Ford 1.8 TDCi Dura Torq engine p/n 609 17 31 32 D Ford 1.8 TDCi Dura Torq engine p/n 609 17 32 33 G Alfa Romeo 145, 146, 147, 156,166, Fiat Brava, Bravo, Marea, Marengo, Multipla, Punto, Stilo and Lancia Lybra with 1,9 JTD and 2,4 JTD engine p/n 609 17 33 34 G M10 x 1,0 Ford 2.0 TDCI / Transit 2,4 TDCI p/n 609 17 81 35 G M8 x 1 Ford 1.4 TDCI Diesel, Citroen C3 HDI p/n 609 17 82 36 D M22 x 1,5 Ford 2.0 TDCI / Transit 2,4L TDCI (not common rail system) p/n 609 17 83 41 D inserted Renault Clio 1,5 CDi (65 and 85 PS) p/n 609 17 41 42 D inserted Renault Laguna 1,9 DTi p/n 609 17 42 46 D Citroen & Peugeot 2,0 / 2,2l HDI 16V p/n 609 17 46 49 G M9 X 1 Alfa Romeo, Fiat, Lancia with 1,9 JTD 16 V engine and identical constructed Opel vehicles (MC Z19DT+Z19DTH) p/n 609 17 34 51 G M10 x 1,25 Opel Astra G, Corsa C, Meriva & Combo with Y17DT + Y17DTL engine, Honda Civic from 01/2002 1.7 CTDi engine code 4EE-2 p/n 609 17 510 52 G M10 x 1,0 Fiat 1,9l JTD 8V from 2000 in the Bravo, Brava, Doblo, Idea, Marea, Multipla, Punto II, Sedici and Stilo, Alfa 1,9l JTD 8V & 2,4l JTD 10V from 00` in the 145, 146, 147, 156 & 166, Lancia 1,9l JTD 8V & 2,4l JTD 10V from ‘00 in the Kappa,` Lybra, Musa & Thesis p/n 609 17 335 54 G M8 x 1,0 MB CDI V6 2,8l + 3,2l engine code OM 642 in the new C-, E-, M-, R-, S class, new Sprinter and Viano MB CDI 4 cil. 1,6l, 1,8l and 2,0l engine code OM 640 in the A- and B-class, CDI 4,2l with engine code OM 629 in the new CLS-, E-, GL-, M-, ML- and S-class p/n 609 17 540 55 G M8 x 1,0 Smart-Diesel p/n 609 17 550 58 D inserted Fiat Ducato 2,8l JTD C-Rail p/n 609 17 58 61 D inserted MAN engine 2866, 2566, MB engines OM 401 / 7 / 9, 421 / 7 / 9, 441 / 7 p/n 609 17 61 63 D inserted MAN D2876 LF 03 p/n 609 17 63 62 D inserted MB engine OM 314, 346, 352, 360, 362, 364, 366 p/n 609 17 62 65 D inserted Opel Corsa C 1,3 D Mc: Z13DT, Fiat 1,3 D Multijet p/n 609 17 21 66 G M8 x 1 Opel Corsa C 1,3 D Mc: Z13DT, Fiat 1,3 D Multijet p/n 609 17 22 66 D inserted Alfa Romeo 156, 166, Fiat Marea, Marengo and Lancia Lybra with 2,4 JTD engine p/n 609 17 66 67 D inserted Opel Movano, Renault Master 2,2 DTI/CDI, e.c.: G9T720 `00 - `03 p/n 609 17 28 68 G M10 x 1 Opel Movano, Renault Master 2,2 DTI/CDI, e.c.: G9T720 `00 - `03 p/n 609 17 29 79 D inserted Fiat Ducato 2,5 TDi, Maxi D/DT `86-94 p/n 609 17 95 Opel Movano, Nissan Interstar, Renault Master 80 D inserted Renault Fuego D p/n 609 17 88 81 D inserted Renault 18D, 20D, 30D and Master p/n 609 17 89 94 D inserted MB E290 / Sprinter with 5-cyl. direct injection p/n 609 17 94 (OM 602.982, OM602.980)
A 4
Accessories for compression tester
Adapter Model A with valve, inner thread M 12 x 1,5 - quick coupler SW adapter / Motometer writer with quick coupler p/n 609 15 80
Model B inner thread M 12 x 1,5 - outside R1/4" SW adapter / Motometer writer with thread p/n 609 18 90
Model. C inner thread M 12 x 1,5 - quick coupler SW adapter / SW pressure loss tester p/n 6096550 p/n 609 17 05
Extensions for compression tester model O Ext. with rubber cone and thread connector 270 mm p/n 609 18 10 Ext. with rubber cone and quick coupler 270 mm p/n 609 18 15
Pressure loss tester model 3 Handy device with 1m hose and quick coupler and a manometer protected by a rubber cap (Ø 80mm), can be calibrated With this equipment it is possible to quickly determine engine failures. Appropriate connecting adaptor must be specially ordered according to engine type e.g. the universal compressed air adapter (spark plug) p/n 609 63 50
Type : Universal Pressure loss tester model 3 p/n 609 65 50
Oil pressure tester model KU The tester is connected in place of the oil pressure switch, in order to test the oil pressure.
The basic equipment consists of: * Manometer 0-10 bar, Ø 80 mm, with rubber cap, p/n 609 26 60 * Hose with quick coupler, 500 mm, p/n 609 29 15 * Angled adapter p/n 609 28 20
Accessories for oil pressure tester model KU Pressure relief valve as intermediate piece to relieve the oil pressure and for bleeding long hose connections. Angled adapter with quick coupler for hard to reach places. Pressure relief valve for oil pressure tester p/n 609 29 40 Angled adapter with quick coupler p/n 609 28 20 Flex. hose with quick coupler 500 mm p/n 609 29 10 Flex. hose with quick coupler 1000 mm p/n 609 29 15 Flex. hose with quick coupler 3000 mm p/n 609 29 30 (for measurements during test drive)
Adapter for oil pressure tester model. K
Adapter for oil pressure tester model SK One side with quick coupler (NW 5), second side with outside thread see the table.
Type thread ANK p/n Alfa-Romeo M 14 x 1,5 19 609 28 50
M 10 X 1 04 609 28 30
R 1/4 x 18 NPTF 39 609 28 70
Audi M 10 x 1 cone short 44 609 28 84
M10 X 1 04 609 28 30
Austin R 1/8 x 27 NPTF 20 608 28 55
Bedford M 14 x 1,5 19 609 28 50
R 1/4 x 18 NPTF 39 609 28 70
BMW M 12 x 1,5 18 609 28 40
M 10 X 1 04 609 28 30
British-Leyland R 1/4 x 27 NPTF 39 609 28 70
R 1/8 x 27 NPTF 20 608 28 55
Chrysler R 1/8 x 27 NPTF 20 608 28 55
Citroen M 12 x 1,5 18 609 28 40
M 14 x 1,5 19 609 28 50
M 16 x 1,5 53 609 28 10
M 18 x 1,5 40 609 28 80
Daewoo M 14 x 1,5 19 609 28 50
DAF M 14 x 1,5 19 609 28 50
Daihatsu R 1/8 x 27 NPTF 20 608 28 55
Fiat M 12 x 1,5 18 609 28 40
M 14 x 1,5 19 609 28 50
Ford R 1/8 x 27 NPTF 20 608 28 55
R 1/4 x18 NPTF 39 609 28 70
M 8 x 1,25 55 609 28 15
Ford Zetec M 10 x 1, cone short 44 609 28 84
General Motor R 1/8 x 27 NPTF 20 609 28 55
Pontiac ¼ x 18 NPT 60b 609 36 00
Honda R 1/8 x 28 BSPP 47 609 28 90
IHC-Schlepper M 10 X 1 04 609 28 30
Innocenti R 1/8 x 27 ASSIT 48 609 28 73
Isuzu R 1/8 x 28 NPTF 56 609 28 16
Lada M 14 x 1,5 19 609 28 50
Lancia M 12 x 1,5 18 609 28 40
M 14 x 1,5 19 609 28 50
MAN M 10X1 04 609 28 30
M 18 x 1,5 40 609 28 80
Mazda G 1/8 x 28 BSP 47 609 28 90
R 1/8 x 27 NPTF 20 608 28 55
Type thread ANK p/n Mercedes-Benz M 14 x 1,5 19 609 28 50 M 10 x 1 04 609 28 30
M8 x 1 52 609 28 09
Mitsubishi R 1/8 x 28 BSPP 47 609 28 90 MWM M 10 x 1 04 609 28 30
Nissan R 1/8 x 28 BSPP 47 609 28 90
R 1/8 x 27 NPTF 20 608 28 55
Opel R 1/8 x 28 BSPP 47 609 28 90
M 14 x 1,5 19 609 28 50
M 14 x 1,5 cone 50 609 28 07
¼ x 18 NPT 60b 609 36 00
Z 22 SE engine M 12 x 1,75 61 609 28 51
Peugeot M 18 x 1,5 40 609 28 80
M 16 x 1,5 53 609 28 10
M 8 x 1,25 55 609 28 15
Porsche M 10 X 1 04 609 28 30
Renault M 14 x 1,5 19 609 28 50
M 18 x 1,5 40 609 28 80
M 16 x 1,5 53 609 28 10
Saab R 1/4 x 18 NPTF 39 609 28 70
Scania M 14 x 1,5 19 609 28 50
Seat M 12 x 1,5 18 609 28 40
M 10 x 1 04 609 28 30
Skoda M 10 x 1 04 609 28 30
Steyer-Daimler M 10 x 1 04 609 28 30
Talbot M 12 x 1,5 51 609 28 08
M 12 x 1,5 36 609 28 56
M 18 x 1,5 40 609 28 80
Toyota R 1/8 x 28 BSPP 47 609 28 90
Vauxhall M 14 x 1,5 cone 50 609 28 07
M 14 x 1,5 19 609 28 50
R 1/4 x 18 NPTF 49 609 28 75
Volvo M 10 x 1 04 609 28 30
M 14 x 1,5 19 609 28 50
R 1/4 x 27 NPTF 39 609 28 70
R 1/8 x 27 NPTF 20 609 28 55
M 18 x 1,5 40 609 28 80
VW M 10 x 1 04 609 28 30
Yucio (Zastava) M 12 x 1,5 36 609 28 56
A 6
Oil pressure tester for automatic transmission
The connection is made with the transmission oil circuit.
Type: e.g. BMW, Ford, Honda, Mercedes, Mitsubishi, Opel and Renault.
Contents: Precision manometer with rubber cap 0 – 25 bar 3m pressure hose, 6 adapter (ANK 4, 18, 20, 55, 60, 61)
Oil pressure tester for automatic transmission p/n 609 29 80
Timing belt tester For controlled adjustment of the timing belt tension. This is absolutely necessary, in order to avoid damage, (e.g. of the water pump or of the valve gear) and the running noise of the timing belt. Type : particularly diesel-engines Timing belt tester p/n 608 45 00
Timing Timing belt tester for belts up to 30mm Universal with 8 inserts This timing belt test tool examines the tension very exactly and is universally suitable for belts up to 30 mm thick. This kit is recommended by ‘’Gates’’ for timing belt testing Timing belt tension tester p/n 908 44 20
Timing belt tension meter with sensor and display in „Newton“ The measuring instrument determines by pneumatic pressure the toothed belt tension in ’’Newton longitudinal force“. The sensor measuring head is constructed in such a way that it can be installed in nearly all engine compartments without complex disassembly. The digital manometer is programmable to the customer's wish and possesses an external interface to exchange data with a computer or a printer. Beside battery operation it is also possible to run the meter using a 12 V car battery. ADVANTAGES: • Applicably for timing belts of all usual cars • Measurement during tensioning of the timing belt • Acoustic and optical signal when a successful measurement is reached.
Timing belt tension meter with sensor and display in „Newton“ sensor testing with vacuum p/n 908 45 00
A 7
Timing belt tester "Elektronik" model 3 For testing of the timing belt tension. The electronic and specialy adjusted software provide for a high repetition accuracy of the results of measurement over a large measuring range. Thus a reliable determination of the timing belt tension is reached. The existing type list can be supplemented partially by comparison with existing measured values. This is a professional device for workshop use and is universally applicable. It has a clearly arranged digital display and a 700mm feed cable attached to the robust measuring head. The special measuring head makes it possible also to test difficult to reach timing belts. The limit stop provides for a long service life of the standard 9V battery. The contact pressure of the feeler is specified by torque delimitation in the measuring head, thus continuous measuring conditions are created and prevent a faulty reading. With an extensive type list the broad measuring range will also permit the examination of future motor vehicle types.
Timing belt tester "Elektronik" model 3 p/n 608 44 50 In a plastic case
Timing belt adjustment keys PSA Timing belt adjusting key 8mm 4-sided drive, 15mm hexagon, length 35mm p/n 908 42 08 Timing belt adjusting key 7mm 4- sided drive, 15mm hexagon, length 35mm p/n 908 42 11 Timing belt adjusting key 7mm 4- sided drive, 15mm hexagon, length 70mm p/n 908 42 12 Timing belt adjusting key 6mm 6- sided drive, 15mm hexagon, length 35mm p/n 908 42 13 Timing belt adjusting key 10mm 4- sided drive, 15mm hexagon, length 70mm p/n 908 42 14 Timing belt adjusting key 15mm hexagon set 3-pcs. consisting of 9084211_12_13 p/n 908 42 15 Timing belt adjusting key 15mm hexagon set 5-pcs. consisting of 9084208_11_12_13_14 p/n 908 42 17
Timing belt adjust spanner 15 hexagon length 550 mm p/n 604 84 15
Timing belt adjustment key Type: Renault petrol engine 2.0 l 16V Timing belt adjust key tapered 9,5 – 10mm 13 hexagon length 47mm p/n 908 42 25
A 8
Allen key 8mm short For the timing belt tension pulley on the FORD Mondeo Allen key 8mm short collet 13mm p/n 608 93 16
Multi-rib belt tensioner model R To pretension the spring loaded multi-rib belt tensioner. Thus the multi-rib belt is eased and can be removed and/or changed. Without this multi-rib belt tension adjuster it is impossible to press back the difficult to reach tensioner. Type: 1,9 DCi engine with e.c.: F9Q e.g. in Renault Megane, Master, Trafic, Laguna, Scenic Multi-rib belt tensioner model R p/n 604 84 22
Tension pulley adjust tool model F For adjusting the timing belt tension.
Type : 1.6 16V `95-03, Brava, Bravo, Marea, Marea Weekend Multipla, Stilo
Tension pulley adjust tool model F p/n 608 43 30
Pulley extraction set 12 pcs. For pulleys on air conditioning compressors. With most automobile manufacturers offering air conditioning even on their smallest vehicle air conditioning repair has become an important topic in the workshop. This versatile set helps to extract the majority of air conditioning compressor pulleys. Pulley extraction set 12 pcs. universal p/n 949 49 90
Pulley extraction set Pulleys Ø till 195 mm Extraction dept two-stage 68 / 88 mm Universal pulley extractor. Due to the small overall height and the special extractor hooks this tool is particularly suitably for confined spaces. With replaceable thrust pieces, in different lengths, a spindle extension and special extendable hooks it is possible to adapt the extractor to the pulley.For pulleys with tapped holes the second extraction bridge is mounted directly. Pulley extraction set p/n 604 87 60 in a plastic case
A 9
Vibration damper / pulley extractor model T4 For extracting the vibration damper e.g. when exchanging a defective vibration absorber. With purpose-built extraction arms to wedge into the ribbed belt profile of the vibration damper. Wedges under the extraction arm fixing bolts increase the contact pressure to the vibration damper. The puller supports itself over the stabilizer base on the 4 bolts that are screwed into the pulley. Thus an unintentional extraction of the timing belt pulley from the crankshaft is prevented and a timing adjustment is not required. Type: VW T4 from 2/96 and identically constructed models partially for the 2,4, 2,5 engines in A6 and also the first Audi 100 Vibration damper / pulley extractor model T4 in a plastic case p/n 604 87 80
Timing belt tension pulley spanner model UNV 155 mm long x 3/8" �-drive Solid tension pulley spanner, for difficult to reach tension pulleys. The spanner has an additional 3/8" � - drive and so can be extended at will. Type : Audi/VW e.g.. Golf Vento 1,5 - 1,9 L, 1,9 L Diesel in the T4 Timing belt tension pulley spanner model UNV p/n 608 41 50
Multi-rib belt spanner 15, 16, 17 & 19mm 550mm long The tensioner is pressed back with the spanners for examination and while changing the multi-rib belt. Type : Audi / VW e.g. : Audi A4, VW Passat from `97 with TDI or pump-injector-engine (Without having to bring the radiator unit to the service position.) Opel DOHC 4- / 6- cylinder, Mitsubishi, Saab V6 engines Multi-rib belt spanner 15mm p/n 604 84 15 Multi-rib belt spanner 16mm p/n 604 84 16 Multi-rib belt spanner 17mm p/n 604 84 17 Multi-rib belt spanner 19mm p/n 604 84 19 Multi-rib belt spanner set 4 pcs. p/n 604 84 45 Multi-rib belt spanner set 2 pcs. (15 & 17mm) p/n 604 84 20 Multi-rib belt spanner set 3-tlg. (15, 17&19mm) p/n 604 84 40
A 10
Special belt tensioning pulley spanner Ratchet ring spanner for use with 3/8” drive ratchets etc. This tool is specific to bolts of type LH-10S, which are used on the belt tensioner of Toyota vehicles with the following engines: 1ZZ (1.8L), 1AZ (2.0L) and 2AZ (2.4L) Type: Toyota with LH-10S screw Belt tensioning pulley spanner TOYOTA with LH-S10 screws p/n 908 42 60
Pulley reaction wrench 1/2" �-drive x 255 mm long
To brace the pulley and to unscrew the fixing bolt.
The rubberized grip with additional � - drive facilitates the
loosening of seized screws.
Model 1 water pump Type : Audi 80, A4, VW Polo, Golf III, Passat
Mod. 2 ZF servo pump / water pump Type : Audi/VW
Pulley brace model 1 p/n 608 96 10 Pulley brace model 2 p/n 608 96 20
Viscous coupling reaction wrench model A 385 mm lg. Special long sturdy pin wrench with adjustable legs for arresting the pulley during viscous coupling disassembly and assembling. Install the fan hub with an 8mm Allen key or viscous coupling jaw wrench model B p/n 608 97 60.
Type : Audi 100, A4 from `95, A6 from `98, A8, V8 VW Passat from `97
Visco coupling reaction wrench model A p/n 608 97 90 with two pair cone points Replacement cone point till 08.2004 p/n 608 97 91 Replacement cone point from 08.2004 p/n 608 97 92
Viscous coupling reaction wrench 46mm For removing the fan bolts. For use on the newer type viscous couplings which are supplied with a 46mm nut. Type : Audi / VW with longitudinal engine
TDC adjusting help model 1 Total length 680 mm. Press the rubber cone of the adjuster into the spark plug hole. Then turn the engine slowly by hand.The level indicator can now be recognized by the floating element (signal piston), when TDC is reached.
TDC adjusting help model 1 p/n 430 12 20
Camshaft pulley extractor model 5 For the disassembly of the camshaft pulley during work on the motor distribution e.g. timing belt change. The spreading cone provides for safe hold of the puller. Because of the additional supporting butt-strap the puller can be used also as an asymmetrical or 2 arm extractor. Type : Universal, specially Audi V6 Camshaft pulley extractor model 5 p/n 430 65 50 Camshaft pulley extractor model 6 Used for the undamaged extraction of 5 and 6 spoke camshaft pulleys. With a centring ball in the spindle and headless screws for fixing the extraction arms. Type : Audi / VW 4- / 6 cyl. TDi engines, V6- / V8- engines e.g. A4, A6, A8, VW Golf, Passat, Porsche Cayenne Camshaft pulley extractor model 6 p/n 430 65 70 Camshaft gauge model 6 For adjusting the cam shaft, e.g. during timing belt change without disassembly of the valve cover. The gauge is screwed onto the cylinder head and grips into the cam shaft Type : Audi / VW 5 cyl. TDi engine, e.g. LT, T4 Camshaft gauge model 6 p/n 430 13 05
Timing tools model CP For blocking and adjusting cam, crankshaft and injection pump during work on the motor distribution e.g. timing belt change. Also contained in the set is an assembly clip, special for fixing the timing belt to the crankshaft pulley as well as a crankshaft pulley puller specific to PSA HDI engines. Type : Citroen/Peugeot petrol and diesel engines incl. HPI and HDI engines Timing tools model CP 21 pcs. in a case p/n 430 24 00
A 12
Timing tools model F For blocking and adjusting camshaft, crankshaft and injection pump during work on the motor distribution e.g. timing belt change. Model FA Type : Fiat 1,7l D/TD from `96- Model FB Type : Fiat 1,9l D from `87- Model FC Type : Fiat und Alfa 1,9l TD from `87- Model FA 4 pcs. p/n 430 23 80 Model FB 4 pcs. p/n 430 23 83 Model FC 4 pcs. p/n 430 23 86 Timing tools model F For blocking and adjusting camshaft, crankshaft during work on the motor distribution e.g. timing belt change
Model FE Type : Fiat Brava, Bravo, Marea + We, Barchetta and Coupe 1,8l 16V petrol
Model FF Type : Fiat Brava, Bravo, Marea + We/Multipla and Palio 1,6l 16V petrol Model FE 6 pcs. p/n 430 23 60 Model FF 5 pcs. p/n 430 23 50
Timing tools model F For blocking and adjusting camshaft, crankshaft and injection pump during work on the motor distribution e.g. timing belt change. Model FG 4 pcs. Type : Fiat Brava, Bravo and Lancia Ypsilon from `95 - 1,4l 12V petrol Model FH 8 pcs. Type : Fiat Brava, Bravo, Marea + We, Scudo, Ducato Ulysse with 1,9l D/DT Peugeot engine from `96- Model FG 4 pcs. p/n 430 23 40 Model FH 8 pcs. p/n 430 23 75
A 13
Universal locking and rigging tool kit for petrol engines with double cam shaft This tool kit offers the advantage to the mechanic of fixing the timing adjustment on petrol engines with double camshaft on several vehicle models. The universal set is suitable for Ford, Honda, Rover, Land Rover, Volkswagen, Seat, Skoda, Audi, Renault, Citroen, Peugeot, Fiat, Vauxhall and Opel models. During all work where the timing belt must be removed it is possible with this locking tool set to lock either with rigging pins the pulleys or with blocking devices the cam shafts and crankshafts so that the gear rim on the flywheel is fixed in the marked position. Universal locking and rigging tool kit 19 pcs. p/n 930 23 00
Dial gauge stand Fiat To adjusting the crankshaft to the TDC. The stand is used in the place of the spark plug. Dial gauge stand I Follower Ø 2 mm, M 14 x 1,25, total length 260mm Type : Fiat/Alfa 1,6l 16V, 2,4l 20V Dial gauge stand II Follower Ø 5 mm, M 14 x 1,25, total length 260mm Type : Fiat 1,8l 16V, 2,0l 20V Dial gauge stand I Fiat without dial gauge p/n 430 21 10 Dial gauge stand II Fiat without dial gauge p/n 430 21 20
Crankshaft / flywheel locking tool model F Model F1 locking tool flywheel Type : Fiat 1.4 12V, Brava/Bravo 95-98, Lancia Ypsilon 96-99 Model F2 locking tool crankshaft pulley Type : 1, 7D / TD/ (KaVEGR) Punto 96-97, 1,9D/TD Tipo/'Tempra/Ducato Model F3 locking tool crankshaft Type : 1,8 16V Stilo 01-02, 1,9D/DT/JDT 96-02, Brava/Bravo /Punto/Stilo/Marea& We, Multipla, 2.4 DT/JTD (96-), Marea& We, Doblo 1,9D 00-02 Model F1 locking tool flywheel p/n 430 21 55 Model F2 locking tool crankshaft pulley p/n 430 21 60 Model F3 locking tool crankshaft TDC p/n 430 21 65 Camshaft locking equipment model 147 For adjusting the cam shaft the blocking tools are attached in place of the cam shaft bearing brackets. The tool supports are marked L1 and L2. Type: Alfa 147 1,6l 16V Camshaft locking equipment model 147; 2 pcs. p/n 430 22 150
A 14
Camshaft locking equipment model F8 The locking tools are mounted in place of the cam shaft bearing brackets. Type: Lancia Kappa 2.0 / 2.4 20 V Camshaft locking equipment model F8 p/n 430 22 45
Camshaft locking equipment model F The locking tools are mounted in place of the cam shaft bearing brackets. Model F1 Alfa 145/146 1.4 & 1.6 Twin Spark (96-), 155/156 1.6 Twin Spark (96-) Model F2 Alfa 145/146 1.8 & 2.0 Twin Spark (96-), 155/156, Spider/GTV 1.8 & 2.0 Twin Spark (96-), Spider/GTV 2.0 16V (95-) Model F3 Alfa 156 2.5 V6 (97-) Model F4 Fiat Brava, Bravo 1.4 12V (95-), Lancia Ypsilon 1.4 12V (96-99) Model F5 Fiat Brava, Bravo, Marea, Marea Weekend 1.8 16V (95-) Model F6 Fiat Barchetta, Coupe 1.8 16V (96-) Model F7 Fiat Bravo, Marea, Marea Weekend, Coupe 2.0 20V & Turbo (94-) Model F1 2 pcs. p/n 430 22 10 Model F2 2 pcs. p/n 430 22 20 Model F3 4 pcs. p/n 430 22 30 Model F4 1 pcs. p/n 430 22 40 Model F5 2 pcs. p/n 430 22 60 Model F6 2 pcs. p/n 430 22 65 Model F7 2 pcs. p/n 430 22 70
Camshaft locking equipment model F
Model F8 Fiat 1,6 18V Bravo/Brava/Stilo 95-02, 1,8 16V Palio 97-02, Model F9 Fiat -1.7 D/TD Punto (96-) Model F10 Fiat -1.9 D Tipo, Tempra, Ducato (87-) Model F11 Fiat -1.9 TD Tipo, Tempra, Ducato (87-) Model F8 2 pcs. p/n 430 22 50 Model F9 p/n 430 22 80 Model F10 p/n 430 22 83 Model F11 p/n 430 22 86
Crankshaft peg out bolt model FO For adjusting the crankshaft to TDC, e.g. during the timing belt change. The peg out bolt is put in place of the crankshaft sensor into the crank case and locks the crankshaft Type : Ford engines 1,8 L D / TD Escort, Fiesta, Orion from `95, Mondeo `93 Crankshaft peg out bolt model FO p/n 430 19 20
A 15
Timing tool set model F1 For locking and adjusting of the camshaft during work on timing.
Type: Ford Fiesta, Puma, Escort/Orion, Focus, Sierra, Mondeo, Cougar, Courier/Kombi and Mazda 121, engines 1,25 till 2,0l-16V Zetec und 1,8l D/TD/TDCi
Camshaft gauge DOHC engines p/n 430 11 90 Locking pin for TDC p/n 430 18 00 Adjusting pin for TDC Ford, Zetec-Se 1.25l p/n 430 19 15 Adjusting pin for TDC II long (M10 x Ø 8 x 79) p/n 430 19 16 Locking pin for camshaft / CAV injection pump (Ø 6 x 65) 2 pcs. p/n 430 19 17 Locking pin Bosch injection pump (Ø 9,5 x 65) p/n 430 19 18 Flywheel locking device (starter end) p/n 608 90 00 Camshaft and pump pulley puller p/n 430 65 30 Timing tool set model F1 p/n 430 72 00
Vibration damper disassembly/assembly tool F/M For work on toothed timing belt change. Type: Ford Fiesta 1.25, 1.4, 1.6l -16V Zetec, Puma 1.4, 1.6, 1.7l -16V, Mazda 121 1.25l - 16V
Timing tool set model R1 For locking and adjusting of the camshaft during work on the timing e.g. changing of the timing belt. Type : Renault Twingo, Clio, Kangoo, Megane/Scenic, Laguna, Espace, Trafic, Express, Extra, Rapid u. R19 engines 1.2-, 1.4-, 1.6-, 1.8-; 2.0 -16V + 1.9-D/TD/DTI Camshaft gauge p/n 430 70 01 Crankshaft locking pin I p/n 430 70 02 Crankshaft locking pin II p/n 430 70 03 Timing tool set model R1 p/n 430 70 00 in a case
Timing tool set model RON
For locking and adjusting of the camshaft and the crankshaft during timing belt change.
Type: Renault Clio, Megane, Scenic, Laguna, Espace, Kangoo, Trafic und Master, Opel Vivaro und Movano `99 -`04, Nissan Micra, Kubistar, Primastar und Interstar with K9K (1,5l cDi), F9Q (1,9l cDi), G9T (2,2l cDi), G9U (2,5l cDi) engines
Timing tool set model RON 9 pcs. p/n 603 88 70
A 16
Timing tool set R/V For locking and adjusting the camshaft and the crankshaft during work on timing:
For adjusting the engine timing along with various locking tools for
crankshafts, camshafts and starter rings
The sets are designed for engines manufactured by Ford, Renault,
VAG and PSA, also used in other model types such as Opel, Nissan,
VW PD, Audi, Seat, Skoda, Citroen, Peugeot etc. Timing adjust and locking tool set for Ford p/n 930 23 10 Timing adjust and locking tool set for Renault p/n 930 23 20 Timing adjust and locking tool set for VAG p/n 930 23 30 Timing adjust and locking tool set for PSA p/n 930 24 00
A 17
Valve spring disassembly / assembly set For the fast disassembly and assembly of valve stem seals Compressed air adapter with compressed air quick coupler, length 150 mm for thread; M 14x1,25, M10x1, M12x1,25 p/n 609 62 40 Compressed air adapter with compressed air quick coupler, length 220 mm e.g.: MB, VW, Ford f. thread M 14x1,25, M10x1, M12x1,25 p/n 609 62 50 Valve spring disassembly / assembly set 7 pcs p/n 902 35 00 Valve spring disassembly / assembly set passenger car 16 V 3 pcs p/n 902 10 00 Valve spring disassembly / assembly set motorbikes 3 pcs p/n 902 13 00
Valve spring compressor set universal This universal valve spring compressor set is ideal for workshops that repair vehicles of several different marks. The set contains 5 driving adaptors: 30mm, 25mm, 23mm, 19mm and 16mm
Valve spring compressor set 7 pcs. p/n 902 36 00
Valve assembly set model U For the disassembly/assembly of valves. Because of the compressed air adapter it is also possible to work with the cylinder head in place. The assembly bracket has 7 retaining positions and a universally applicable lever to allow the versatile employment of the tool. Contents: 2 x assembly bracket 1 x axel 515 mm 1 x assembly lever 1 x disassembly / assembly compression piece Ø 22mm 1 x assembly aid 1 x Compressed air adapter flexible.. M14/18 350 mm 1 x Compressed air adapter inflexible M14/18 115 mm 1 x Compressed air adapter diesel injectors M24 x 2 4 x quick coupler connector 1 x assembly set (screws, washers and pins) Valve assembly set model U p/n 600 90 00
A 18
Compressed air adapter flexible To hold the valves closed, as the combustion chamber is pressurised with compressed air. The adapters are screwed in place of the spark plugs or glow plugs. Use e.g. with valve stem repairs or with the pressure loss tester. Model 1 - 4 with flexible reinforced hose Model 1 type : universal (spark plug) Model 2 type : Ford DOHC (spark plug) Model 3 type : Opel Isuzu diesel engine 1,7TD / 1,5D (glow plug) Model 4 type : universal (glow plug) Model 5 type : universal Compressed air adapter flexible model 1 M14 x 1,25 x 250 mm p/n 609 63 50 Compressed air adapter flexible model 2 M14 x 1,25 x 250 mm p/n 609 63 55 Compressed air adapter flexible model 3 M10 x 1,25 x 250 mm p/n 609 63 60 Compressed air adapter flexible model 4 M12 x 1,25 x 250 mm p/n 609 63 65 Compressed air adapter inflexible model 5 M14 x 1,25 x 220 mm p/n 609 62 50 (diesel adapter see compression writers)
Reaction wrench model U3 with a reference circle of 45 mm to 350 mm Universal reaction wrench for holding e.g. transmission and differential flanges, crankshaft and camshaft pulleys With replaceable, hardened screwed ends Handhold 400 mm Lg. p/n 608 46 71 Applicator for reaction wrench without screwed ends p/n 608 80 81 Screwed ends with groove Ø 10 u. 12 mm 2 pcs.* p/n 608 80 82 Screwed ends with groove Ø 8 u. 14 mm 2 pcs.* p/n 608 80 83 Screwed ends with groove Ø 7 u. 9 mm 2 pcs.* p/n 608 80 84 Reaction wrench model U3 p/n 608 80 80 3 pair screwed ends with groove p/n 608 80 85 in a plastic case
A 19
Face milling device crankshaft model 3 For repairing (re-milling) the damaged fitting surface of the crankshaft face. For correct seating of the new timing belt pulley it is necessary to rework the damaged fitting surface of the crankshaft in order to prevent further loosening. A centring pin is placed in the crankshaft in order to get an accurate angle and flat surface Type : Audi, VW, Ford, Seat, Skoda 1,9 L diesel engines 5 cyl. engines (e.c.: e.g. ACV, AHY) Contents: Face cutter model 2 35 mm p/n 608 88 91 Centrering bolt size 1 M14 x 1,5 x 73 mm p/n 608 88 82 Centrering bolt size 2 M18 x 1,5x 88 mm p/n 608 88 92 Special spanner p/n 608 88 83 Cleaning brush p/n 608 88 84 Face milling device crankshaft model 3 p/n 608 88 70 in a plastic case Supplements Centrering bolt size 3 4 cyl. engines with crankshaft thread M16 x 1,5 Type : Audi/VW 4 cylinder engine code AGR Centrering bolt size 4 Long centring bolt for engines with a deep crankshaft thread. Type : VW 5 cylinder ACV from engine nr. 048 995 >> and AAB from engine nr. 424 606 >> Centrering pin size 3 M16 x 1,5 x 73 mm p/n 608 88 87 Centrering pin size 4 M18 x 1,5 x 131 mm p/n 608 88 93
Cylinder head socket inserts Ribe 1/2" �-drive Model 1R Ribe 12 x 120 mm Type: Fiat with petrol engines Model 2R Ribe 13 x 120 mm Type: Fiat Bravo, Brava, Alfa, Lancia Kappa Model 3R Ribe 14 x 100 mm Type: e.g. Fiat Thema, - Ducato, Lancia Dedra, Tipo, Tempra, diesel engines 1930 + 2500 cm
3
Model 4R Ribe 9 x 100 mm Type: e.g. Fiat 1,4l 16V Cylinder head socket insert model 1R p/n 792 21 20 Cylinder head socket insert model 2R p/n 606 22 80 Cylinder head socket insert model 3R p/n 792 21 40 Cylinder head socket insert model 4R p/n 792 21 09
A 20
Cylinder head socket insert Torx 55 T-profile socket insert T 55 x 140 x 1/2" �-drive Type : Ford OHC und DOHC Renault engine code : G8T + all from ´95 Opel 6- cyl. series MB engines 112,113 T-profile socket insert T 55 p/n 788 55 50
Cylinder head socket E 20 -NFZ E-profile E 20 x 132 mm x 1/2" �-drive Type : MAN F2000, F90, F8 and busses with the engines D25 / D28 Cylinder head socket E 20 p/n 606 14 20
Cylinder head socket 3/4“ Impact commercial vehicles 3/4“ �-drive, without chamfer For the disassembly and assembly of cylinder head screws on commercial vehicles. Type : MB, MAN e.g. SW 17 MB / MAN SW 19 MB Actros E 18 MAN model M 2000, busses with engine D08 E 20 MAN model F 2000, F90, F8, busses with engine D25 / D28 Cylinder head socket 17 12 sided x 110 p/n 606 28 17 Cylinder head socket 19 12 sided x 110 p/n 606 28 19 Cylinder head socket E 18 x 110 p/n 606 28 18 Cylinder head socket E 20 x 110 p/n 606 28 20 Cylinder head socket E 22 x 110 p/n 606 28 22 Cylinder head socket E 24 x 110 p/n 606 28 24
Piston ring compressor Pistons 75 - 125 mm Ø Bandwidth 38 mm With profiled band Low friction between the band and piston ring, The band can not slip into the cylinder. One time adjustment for several piston rings of the same diameter. Piston ring compressor p/n 607 30 00
A 21
Piston ring compressor A ratchet with release lever ensures the fast compression of the piston rings. The band is made of sprung steel.
Ratchet For pistons Ø Bandwidth P/n
without 40 - 75 44 mm 607 20 50
with 54 – 125 89 mm 607 20 00
with 90 - 175 89 mm 607 21 00
with 90 - 175 165 mm 607 21 50
Cylinder hone brushes
These hone brushes are auto centring and produce a finely polished surface for a long life span. All brushes have a range of tolerance of +/-2 mm the diameters are graduated in the sizes below. Hone brush SIC grain 240 outside Ø 10,0mm p/n 913 60 10 Hone brush SIC grain 240 outside Ø 15,0mm p/n 913 60 15 Hone brush SIC grain 240 outside Ø 20,0mm p/n 913 60 20 Hone brush SIC grain 240 outside Ø 25,0mm p/n 913 60 25 Hone brush SIC grain 240 outside Ø 30,0mm p/n 913 60 30 Hone brush SIC grain 240 outside Ø 35,0mm p/n 913 60 35 Hone brush SIC grain 240 outside Ø 40,0mm p/n 913 60 40 Hone brush SIC grain 240 outside Ø 45,0mm p/n 913 60 45 Hone brush SIC grain 240 outside Ø 50,0mm p/n 913 60 50 Hone brush SIC grain 240 outside Ø 55,0mm p/n 913 60 55 Hone brush SIC grain 240 outside Ø 60,0mm p/n 913 60 60
Cylinder hone tool 1/4" flexible drive shaft for drills with speeds of 1500 to 2500 rpm. Self spreading hone arms, contact pressure is adjustable.
Model Cyl-Ø mm
Hone arms mm
Stone length
mm
Total length
mm p/n
A 15- 45 2 28 20 613 60 00
B 22- 50 3 28 205 613 61 00
C 50-135 3 75 270 613 62 00
D 50-175 3 100 300 613 63 00
Replacement segments (set) :
For tool Stone
length mm Standard Fine Crude p/n
A 28 x - 613 60 10 A 28 - x - 613 60 20 B 28 x - - 613 61 10 B 28 - x - 613 61 20 C 75 x - - 613 62 10 C 75 - x - 613 62 20 C 75 - - x 613 62 30 D 100 x - - 613 63 10 D 100 - x - 613 63 20 D 100 - - x 613 63 30
A 22
Neway valve seat cutter set Universal set passenger car valve Ø 28-46m 203,212,217,622 with pilots p/n 601 00 50
Nr: Head- Ø
mm
Operational range min max mm mm
Angle° Repl. blades
Type Nr. quantity p/n .
203 31,8 29 38 31°x46° 250 3/3 601 20 30
212 31,6 29 38 15°x75° 250/254 3/3 601 21 20
217 38 35 44 15°x75° 251/254 3/3 601 21 70
622 38 35 44 31°x46° 251 5/5 601 62 20
Universal set trucks 203,212,217,622,642,643,652, 653,672,674 with pilots p/n 601 01 30
Nr: Head- Ø
mm
Operational range min max mm mm
Angle° Repl. blades
Type Nr. quantity p/n .
203 31,8 29 38 31°x46° 250 3/3 601 20 30
212 31,6 29 38 15°x75° 250/254 3/3 601 21 20
217 38 35 44 15°x75° 251/254 3/3 601 21 70
622 38 35 44 31°x46° 251 5/5 601 62 20
642 44,5 42 50 31°x46° 251 5/5 601 64 20
643 44,5 42 50 15°x60° 251/254 5/5 601 64 30
652 50,8 48 57 31°x46° 251 5/5 601 65 20
653 50,8 48 57 15°x60° 251/254 5/5 601 65 30
672 63,5 61 70 31°x46° 251 7/7 601 67 20
674 63,5 61 70 15°x60° 251/254 5/5 601 67 40
Universal set passenger car 16V - diameter 28,6 mm 68,269,278 / 3 pilots p/n 601 04 50
Valve seat cutters set model NW Type : Opel engines X 10 XE, X 12 XE Contents: Rotary handle for valve seat cutter S 100 p/n 601 96 00 Valve seat cutters nr. 122 / 45° p/n 601 12 20 Valve seat cutters nr 121 / 15° p/n 601 12 10 Pilot 100 - 5,0 mm p/n 601 71 11 Allen key 5/64" p/n 601 97 00 Cleaning brush p/n 601 99 00 Valve seat cutters set model NW p/n 601 05 40 In a plastic case
Valve cone milling tool model 2 The valve cone milling tool with integrated linear feed unit permits a precise, fast and low-priced treatment of valve cones of 30° and 45° It is suitable for valves with a cone Ø of 16 - 54 mm and a stem Ø of 3,8 - 13 mm. Valve stem guiding sleeves are not needed with this model. Valve cone milling tool model 2 p/n 601 40 00
Rotary handle with crank lever Rotary handle with crank lever for cutter S200/600 this rotary handle makes possible an exact, precise operation due to the even contact pressure produced by the spring action. Rotary handle with crank lever p/n 601 96 50
Separation and rivet tool for motorcycle driving chains Here we offer a tool for the separation and riveting elements in drive chains. Most frequent application is the moped and motorcycle sectors. Separation and rivet tool for motorcycle driving chains p/n 908 40 00
XZN socket inserts Socket inserts with □-drive ½ “in short 40.0 mm and long 75.0 mm version XZN M14, XZN M16 and XZN M18. These are needed for the disassembly and assembly of the special screw connections in the chassis and the engine support. Made in one piece, these inserts are extremely tough. XZN socket inserts ½“-drive, 6 pcs p/n 794 05 00
B 01
Tow hitch in vehicle tester 12 Volt LED display with a 5m feed cable For examining the electrical connection at the tow hitch. This is a robust tool designed to save time and money for the workshop.
From the driver's seat it is possible to check: Turn signals right/left, brake light right/left, tail lights right/left reversing light, Fog tail light, Fog tail lights disconnection when using a trailer. Also suitable for lamp control systems.
Tow hitch in vehicle tester 12 Volt p/n 861 61 50 with 13-pin DIN 72570 connecter plug
Multi tester Universal multi-tester in an impact protected plastic housing. With digital 7 digit LCD and an additional bar line display. Overload safety device with optical and acoustic signal. Automatic shut off after 30 minutes. Basic functions for the rotary switch: Temperature measurement, diode test, passage test, ohm meter, voltage measurement, current measurement, number of revolutions, work cycle, frequency and dwell angle. Through a 9 V battery, the device is independent Includes are: Storage bag, measuring cable, inductive clamp, thermo feeler, 9 V battery. Technical data: Safety fuse: 2 A 600 V and 15 A 600 V Voltage: max. 1000 V Dimensions: 203 x 100 x 47 mm Multi tester p/n 609 99 00
Universal 13 pcs. set with measurement and test cables High quality tool for the car electrician is an indispensable test cable set for use with testers, test lamps, Multi meters etc. The set can be used for example to test bad mass connections, continuity tests, polarization or for operating electric devices such as starter motors, wiper motors, electric power windows, electric antennas, etc. Measurement and test cable set 13 pcs p/n 951 48 00 Measurement and test cable set 15 pcs with 2 piercing aids. p/n 951 48 05 Piercing aids for circuit tester with special steel points and cable. p/n 951 47 50
B 02
Electronic protection This equipment is designed for the protection of electronic units in motor vehicles against voltage peaks, e.g. during welding, during loading of the battery, or during starting aid. Thus electronic units in the vehicle can be protected, without having to disconnect the battery. The equipment is attached to the battery and automatically identifies voltage, so it can be used with both 12V and 24V systems. Voltage suppression: > 15 V/25 V Electronics protection p/n 410 60 00
Central connector dismounting VW-Sharan, Ford-Galaxy, Seat-Alhambra For the disassembly and assembly of the difficult to access central connectors, which are built into the cross-beam of the door. Triple adjustable groove nut spanner. Suitably for VW Sharan, Ford Galaxy, Seat Alhambra. Central connector groove nut spanner p/n 607 63 00
Alternator many toothed key 33 teeth For the disassembly and assembly of the free-wheel when changing the alternator or the pulley. With a socket insert which engages the generator arbour, e.g. MT/XZN 10, Fiats / inbus 7, the screw connection problem is solved Model 1 Without socket insert p/n 604 82 85 SW 17 6-kant, bore hole 12mm, 30mm long Type : Audi, VW, Fiat, Ford, Porsche, Seat, Skoda Model 2K Socket insert XZN 10 x 110 mm p/n 604 82 80 1/2" �-drive 22 mm hexagon Model 2L Socket insert XZN 10 x 135 mm p/n 604 82 83 1/2" �-drive 22 mm hexagon Type : Audi, VW, MB, Seat, Skoda u. a. Model 3K T-profile T 50 x 110 mm p/n 604 82 95 1/2" �-drive 22 mm hexagon Model 3L T-profile T 50 x 135 mm p/n 604 82 93 1/2" �-drive 22 mm hexagon Type : Renault, Peugeot
Connector release set 2 pcs. consists of 19729-08, 19729-08E p/n 951 50 00 Spare points 19729-08K, 19729-08EK p/n 951 50 10 Connector release set 2 pcs with spare points p/n 951 50 20 Connector release set 4 pcs. for Japanese vehicles consists of 19729-08, 19729-08E, 19719-05, 19719-05E with spare points p/n 951 60 00 Connector release set 5 pcs. p/n 951 55 50 Spare points for connector release set 5 pcs. p/n 951 56 00 Connector release set with spare points p/n 951 55 00
Identification mark tool
Identification mark spare point(s)
Point thickness ( t ) / mm
Point width ( b ) / mm
Adjusting dimension ( e ) / mm
19719-05 E 19719-05 EK 0,5 0,8 single point
19719-05 19719-05 K 0,5 0,8 2,2
19729-05 19729-05 K 0,5 1,5 3,3
19729-08 19729-08 K 0,8 1,5 3,3
19729-08 E 19729-08 EK 0,8 1,5 single point
B 04
Alternator socket insert and bit set Toolset for stopping the alternator axle and at the same time release or tighten the free-wheel pulley. Alternator socket insert and bit set 12 pcs p/n 904 83 00 in plastic case.
Alternator Socket insert Inbus 7mm and pin wrench Type :Fiat, Lancia, Alfa Alternator socket insert Inbus 7mm and pin wrench p/n 904 82 50
UV detector light flexible 440 mm long For leak detection in air conditioning systems. This is an extra slim "pen lamp" with an ultra bright, broad ray of light and a flexible body, which is adjustable to any possible angle. As a result the difficult to access parts of the air conditioning system can be illuminated e.g. deepl in the engine compartment or under the instrument panel. The system must be filled with UV active liquid. UV eyeglasses make it additionally easy to recognize of leakages UV detector light flexible p/n 649 52 00
Line link release tie-clip
For lines-Ø 1/4, 5/16, 3/8, 1/2, 5/8, 3/4, 7/8 For quick hose clips e.g. on air conditioning systems or fuel pipes Typ : Universal, z.B. Opel, Ford Line link release tie-clip set 7 pcs. p/n 605 04 90
Test devices for starter batteries up to 12,75V SBC LC tester and SBC tester with printer also used for testing the alternator These two highly sensitive battery test devices work in a voltage range of 6,00V to 15,00V and a CCA minimum starter current of 10A and CCA max. starter current of 1500A. The test results can be obtained using 4 guidelines, IEC, SAE, DIN and EN. Test options are: alternator tests, starter impact, short-circuit protection. Using model 9206500 it is possible to then print the results using the devices SBC printer. The battery data must be entered for example 12,75V as well as the test standard e.g. DIN, also the temperature if under or over 0°Celsius. After a few seconds the determined condition of the battery is displayed. These battery testers function without external operating battery. Battery load examiner with LCD display p/n 920 60 00 Battery load examiner with LCD display and printer function p/n 920 65 00
B 05
Adjusting tool for start of fuel delivery Release nut, pin wrench, reduction adapter for adjusting the start of fuel delivery with Bosch & CAV pumps. Using the pin wrench the two-piece pump impeller is rotated. Type: Renault Clio, Laguna, Megane, Scenic, Express /Extra, R19, Kangoo, Opel Movano, Arena; Mitsubishi Carisma from `97, Volvo S40+V40 and engine code F8Q und F9Q Adjusting tool for start of fuel delivery 3-tlg. p/n 430 18 90
Pressure and negative pressure testing set
For leak testing of petrol and diesel fuel systems.
Easy to use with connectable adapters that are contained in the
case. Manometer from -1 to 9 bar with rubber protection. Specification: • Manometer with pressure and negative pressure display • The examination of the suction face of the fuel pump is possible • Air bubble recognition by Plexiglas / inspection glass function • Adapter particularly to vehicles with plastic quick-couplers Type: Mercedes: A class, B class, C class, CLK, CLS, E class,
GL class, ML class Seat: Alhambra, Ibiza, Leon, Toledo 3 Skoda: Octavia, Roomster
VW: Caddy, Crafter, Eos, Golf 5, New Beetle, Passat, Phaeton V6, Polo, Touareg, Touran, etc.
Pressure and negative pressure testing set p/n 909 59 55
Negative pressure pump Robust complete metal version Metering range: negative pressure to -30 in Hg, -76 cm Hg or -1 bar Complete in plastic case with accessories: several adapters, a container for examining fluids such as gasoline, brake fluid, water etc.. Negative pressure pump p/n 609 85 50
Pressure and negative pressure pump Robust complete metal unit can be switched between pressure and negative pressure. Metering range: pressure to 4 bar negative pressure to -1,0 bar Complete in plastic case with accessories: several adapters and containers for examining fluids such as gasoline, brake fluid, water etc. Pressure and negative pressure pump p/n 609 87 50
B 06
Pressure and negative pressure pump model 2 Robust complete metal unit. Can be switched between pressure and negative pressure.. Metering range: pressure to 1,5 bar negative pressure to -1,0 bar Complete in a case with many accessories: several adapters and a container for examining fluids such as gasoline, brake fluid, water etc Pressure and negative pressure pump model 2 p/n 609 08 50
Pressure and negative pressure pump model HV90 Robust complete metal unit. Can be switched between pressure and negative pressure. Metering range: pressure to 1,5 bar negative pressure to -1,0 bar Complete in a case with several adapters Pressure and negative pressure pump model HV90 p/n 609 08 00
Turbocharger pressure test unit model C Range -1 to 3 bar, precision manometer 100 mm Ø, 3 m PVC hose with 3 way splitter For turbocharger compression test while driving. Turbocharger pressure test unit model C p/n 609 81 00
Exhaust pressure testing device
Manometer Ø 63 mm, -1 till +3 bar,
Connecting piece M 18 x 1.5, pressure hose 3 m long By examining the exhaust pressure a fast diagnosis of the catalytic converter is possible. To be mounted in place of the lambda probe. Exhaust pressure testing device p/n 604 58 50
Combination socket set 7 pcs A socket set for the removal of lambda probes, injectors , sensors and switches. Special sockets with slots or windows in long or special short versions - in the sizes 22 (7/8"), 27 (11/16") and 29mm Combination socket set 7 pcs p/n 905 90 00
B 07
Fuel extraction station model 2 Electrical extraction apparatus for fuel from passenger car tanks etc. This model is equipped with a high delivery pump with a capacity of 200 L/hr. The barrel takes up 120l of fuel for short term storage. It is then emptied by changing the hoses. Equipment voltage: 12 V automotive battery, 5m cable. suck/pressure hose: 1,5 and 2,5m Security: Overloading protection, TÜV and PTB examined, CE mark Pump for 12 V - connection (model 2) p/n 806 61 00 Barrel 120 L with overflow automatic shut-off p/n 806 62 00 Barrel car universal p/n 806 53 50 Fuel extraction station model 2 comp. 12 V , 3 pcs. p/n 806 60 00 Spare part: Fuel filter p/n 806 51 50 Diesel filling device Containers 1.8l, and 6 to 10 bar, Air consumption 180l/min (efficiency 60% /vacuum) Compressed air bleed port 1/4 “, hook, 3 x silicone hose inside Ǿ 4/6/8.5 mm Vacuum device for fast, clean and problem-free bleeding and/or filling of diesel filters and brake assemblies in most motor vehicle types e.g. diesel passenger cars filter changes, run dry tanks, wrong refuelling or for the brake bleeding of motorcycles The venturi nozzle produces a vacuum in the container, then using the extraction hose liquid can be sucked off and/or sucked in. (Compressed air must thereby be permanently attached.) Type: Universal (is suitable for diesel and brake fluid) e.g. Audi/VW PD engines diesel filter change (all 60000Km/ when using biodiesel all 30000 km), MT-CDI-engines, PSA HDI engines, as well as Renault, Fiat direct injection etc.
Warning! Do not use for easily inflammable liquids e.g. petrol
Fuel pipe release tool model V 210 mm long For the damage-free loosening of the fuel line connectors e.g. between fuel filters and line. For difficult installation positions the pliers head is bent to 90°. Type : Alfa, Audi, VW, Fiat, Lancia and Volvo Fuel pipe release tool model V p/n 605 04 80
B 08
Fuel pipe release tool model F2 For the loosening of the plug connectors on fuel pipes and fuel level sensors.
Type : Ford DOHC Motor
Fuel pipe release tool model F2 p/n 605 03 50
Fuel filter tool 1/2" � drive For the damage-free disassembly of the fuel filter housing cover screw connection when renewing the filter cartridge
Type : PSA
Fuel filter tool p/n 912 08 96
Hose clamp pliers " Clic" To open and close " CLIC" type - Clips. These clips can then be reused. Type: e.g. VW - Audi fuel pipes, Expansion tank water, BMW windshield wiper system among other things Opel’s brake booster VW Polo hose clamp pliers " Clic" Hose clamp pliers " Clic" p/n 605 02 50
Hose clip pliers model F With flexible cable for remote control (530 mm) For use on hose clips on coolant and fuel hoses, cv boots etc. universal applicable, for nearly all passenger car marks. No damage to clip or hose. Allows problem-free, fast removal of coolant hoses. Hose clip pliers model F p/n 605 03 25
Hose clip pliers model ES for Clic clips A pair of pliers to open and close Clic clips. With this model the inserts are replaceable and twistable in order to reach the most difficult to access clips. Hose clip pliers model ES for Clic clips p/n 605 02 70
B 09
Hose clamp pliers for MUBEA clips For use on the new hose clips which are used in VW Passat turbocharger suction hoses and in the T5 water hoses with clamps MU56 or MU65. To cover both large and small clips both pliers are required. Hose clamp pliers for MU25,MU26,MU27,MU40 p/n 905 02 93 Hose clamp pliers for MU56,MU65 p/n 905 02 95
Fuel injection system pressure test set model 3 Extensive set for fuel pressure testing of petrol engine fuel injection systems. Precision manometer 0-10bar with fine adjustment Set contents in the case: Manometer Ø 100 mm, 0-10bar p/n 609 53 00 3 way valve p/n 609 52 50 Reinforced hose 260 mm with quick coupler and nut p/n 609 46 50 Reinforced hose 260 mm with two nuts p/n 609 52 00 21 Connecting adaptors with quick-coupler: 01 Fiat LE-Jetronic p/n 609 45 10 02 Fiat LE-Jetronic, Ford, BMW (just hollow bolt) p/n 609 45 20 03 MB, Golf, BMW, Audi 100 5-cyl. + DPAK 14 p/n 609 45 30 04 Porsche 911, Audi, Peugeot, Renault, Fiat p/n 609 45 40 05 Saab, Renault Audi 5-Zyl.,VW Golf, Fiat p/n 609 45 50 06 BMW p/n 609 45 60 07 Opel-Astra, BMW, Fiat, Alfa-Romeo, Nissan p/n 609 46 70 Mazda, Renault Twingo, Peugeot-806, Citroen Evasion 08 MB p/n 609 46 80 09 Ford, Mitsubishi, Golf 16 V p/n 609 46 90 11 MB p/n 609 47 10 12 Alfa, Peugeot, Volvo, Fiat Croma, Seat VW, Audi p/n 609 47 20 13 Peugeot, Fiat Croma, Audi 6-Zyl. p/n 609 47 30 14 Audi, Porsche 911, 928 924, Audi 100 5cyl. p/n 609 47 40 21 Ford Standard / 2,8i , Golf 16 V p/n 609 48 10 22 Opel-Motronic 1.5, 2.5, 4.1 p/n 609 48 20 26 Ford EFi 2.4 + 2.9 L p/n 609 48 60 28 MB and Opel LMH p/n 609 48 80 29 Ford p/n 609 48 90 30 Ford-Zeta + SEFi, Peugeot HPi 206 / 307 p/n 609 49 00 31 2-tlg. Audi/VW Bosch-Mono-Jetronik ec: RP p/n 609 49 10 32 Opel -Motronic p/n 609 49 20 Fuel injection system pressure test set model 3 p/n 609 59 70
B 10
Pressure test adapter QC One side with quick-coupler, second side with vehicle-specific thread. O = outside thread, I = Inside thread, A = angle adapter
QC Thread Type p/n.
01 M 14x1.5(O,A) American vehicles, Fiat LE-Jetronic 609 45 10
02 M 12x1.5 (O,A) American vehicles, Fiat LE-Jetronic, Ford Fiesta, Escort 1.1, BMW (just hollow bolt)
604 45 20
03 M 8x1 (O) BMW, MB, VW Golf, Audi 100 5 cyl. + QC 14 609 45 30
04 M 12x1.5 (O) Audi 5-cyl., Peugeot 205, 309, 405, Porsche 911, 928, 924, Renault 9/ 11/18,GTX 11,TXE, Fiat L-Jetronic +QC 05, Fiat Monotronic +QC 07
609 45 40
05 M 12x1.5 (l) Audi 5 cyl., VW Golf, Fiat L-Jetronic + QC 04, Porsche 911 3.6l, 944 3.2l, 928 S4, Renault 4, 9, 18, GTX 11, TXE, Saab,
609 45 50
06 M 8x1 (l) BMW 609 45 60
07 1 x Ø 6mm^ 1 x Ø 8mm
Opel-Astra, BMW, Fiat Uno, Lancia, Alfa-Romeo, Nissan, Mazda Renault Espace, Twingo, Peugeot-806, Citroen Evasion
609 46 70
08 M 10 x 1 (O) MB 609 46 80
09 M 10x1 (O,A) Ford, Mitsubishi, VW Golf 16 V 609 46 90
10 M 8x1 (O) special
adapter Audi 609 47 00
11 M 8x1 (l) MB 609 47 10
12 M 14x1.5 (l) Alfa-Romeo, Peugeot, Volvo, Fiat-Croma, Seat (Ibiza, Malaga), VW-Monojetronic, Audi 6 cyl. + QC 13
609 47 20
13 M 14x1.5 (O) Peugeot, Fiat-Croma, Audi 6 cyl. + QC 12 609 47 30
14 M 8x1 (O,A) Porsche 911, 924, 928 am Warming up automatic controller , Audi 100 5 cyl. + QC 03
609 47 40
15 M 10x1 (l) Ford 609 47 50
16 M 8x1 (l) special adapter MB 609 47 60
19 M 16x1.5 (O) Citroën XM, Ford Scorpio, engine DOH 2.0 L, Opel `97 1.4L
609 47 90
20 M 16x1.5 (l) Citroën XM, Ford Scorpio 2.8i 609 48 00
21 M 10 x 1 (l) Ford Standard, VW Golf 16 V 609 48 10
( I ) like qc 22, but with O-ring, Chrysler, Ford Efi 2.4i + 2,9 i, MB,
609 48 60
28 7/16"-20UNF V6 (l, A) swivelling
like qc 22, however swivelling and with O-ring, 8x2.5, MB, L+H Jetronic, LMH Motronic, Opel Ecotec, Porsche
609 48 80
29 VG 8 with release pin
(I,A) swivelling, with angle, Ford-Mondeo 609 48 90
30 VG 8 with release pin (l) Ford Mondeo, Volvo 850, Peugeot HPi 206, 307, 406, Opel
609 49 00
31 Female hose connector
8 mm 2-tlg
Bosch Mono-Jetronic for VW Motor RP 609 49 10
32 M 14x1.5 (l)
with closing dome Opel Motronic, VW Golf II 609 49 20
B 11
Vacuum box Housing: Shatter-proof plastic Suction volume: approx. 14 litres L/W/H: 300/200/350 mm Weight: 3.3 kg. Drain valve, 2 m suction hose and double cone point
For the bleeding and suction of liquids. The box is independently applicable, a manometer and level indicator inform the status of application.
Areas of application: Pre-bleed of Diesel fuel injection systems after fuel filter change. Change of e.g. water, coolant or brake fluid, oil (engine oil, transmission oil, etc.) Vacuum box p/n 806 36 00 Adapter suction hose CDi Overall length 1000 mm, coupling for MB fuel filter. For the ventilation of the fuel system over the Diesel filter.
Type : MB with CDI engine
Adapter suction hose CDi p/n 806 36 10
Injector pressure test device Precision manometer: Ø 100 mm, grade 1.0 with rubber protective cap
Desktop device for the examination of Diesel injection nozzles on opening pressure, spray pattern and leak tightness of the injection nozzle. During the examination the liquid is squirted back into the fluid reservoir (330 cm ³) with spray protection. The pumping lever can be changed for easier pumping to the front position (piston displacement 35 cm ³). The drag pointer stops once the pressure required for the nozzle to open is reached. Thus it is not necessary to observe both the jet of the nozzle and the manometer.
One pressure pipe (thread M 12 x 1.5) and 3 connecting adaptor are provided. M 14 x 1.5 universal M 12 x 1,25 VW/Audi TDi M 10 x 1 (with sealing cone) Opel DTL/DTH
1) Injector pressure test device 0 - 400 bar with drag pointer p/n 430 53 40 2) Injector pressure test device 0 - 600 bar with drag pointer p/n 430 53 60
Diesel supply pressure testing set Manometer : -1 till 9 bar, Ø 63 mm Feed line: 2 x 3 m, oil and petrol resistant Adapter R 1/4" inner- and R 1/4" outside thread For a fast and reliable pressure test, also during test run. In one step the opening pressure of the overflow valve the maximum pressure of the fuel pump and bubble-free transfer are examined. The transparent centre section permits an evaluation of the fuel. Moreover the negative suction pressure can be examined. Diesel supply pressure testing set p/n 609 83 20
B 12
Injection pump locking pin For locking the injection pump, e.g. during timing belt change. Mod. 2 Ø 15,0 mm Type : VW 5 cyl. 2,4L D Injection pump locking pin model 2 p/n 430 19 30
Glow plugs drilling set M 8x1 Drilling and extracting tool set for broken off CDI glow plugs with thread M 8 x 1. During disassembly of extremely seized glow plugs the drive hexagon can often be sheared off. While still attached to the glow plug body the central contact of the glow plug prevents the drive hexagonal from being removed. Using this tool set in a few steps the central contact is removed, the glow plug thread is drilled and the glow plug body is pulled out of the cylinder head. Type: MB engine OM 642 ( V6 2,8 l + 3,2 l ) in the C, E, M, R, S class, new Sprinter and Viano. Glow plugs drilling set M 8x1 p/n 604 16 40 in a case In addition recommended: Thread repair set, supplement to the drilling set M8 x 1 p/n 604 16 85
Glow plugs drilling set M 10 x 1 Drilling and extracting tool set for broken off CDI glow plugs with thread M 10 x 1. During disassembly of extremely seized glow plugs the drive hexagon can often be sheared off. While still attached to the glow plug body the central contact of the glow plug prevents the drive hexagonal from being removed. Using this tool set in a few steps the central contact is removed, the glow plug thread is drilled and the glow plug body is pulled out of the cylinder head. Type : CDi glow plugs M10 x 1 Glow plugs drilling set M 10 x 1 p/n 604 17 40 in a case
Glow plugs drilling set M10x1 Renault G9T & G9U
Tool kit designed to drill and extract broken off M10x1-glow plugs from the Renault G9T and G9U engines Glow plugs drilling set M10x1 Renault G9T & G9U p/n604 18 70 in a case
B 13
Glow plugs drilling set M8x1 Tool kit for drilling and extracting broken off M8x1 glow plugs in Fiat/Opel 1,3l Multijet engines. Glow plugs drilling set M8x1 for Fiat/Opel 1,3l Multijet engines p/n 604 16 60
Glow plug reamer model I M 8 x 1 Type: CDI engines e.g. MB, Opel, Renault Glow plug reamer model I M 8 x 1 p/n 604 16 25
Special thread repair set For glow plug M8 x 1, 7 pcs Special tread repair set for glow plug M8 x1, 7 pcs p/n 604 16 85
Stepped glow plug reamer For cleaning the glow plug shaft and the sealing seat in the cylinder head for MB CDI glow plugs M 10x1 with actuator and guidance. Stepped glow plug reamer for MB CDI glow plugs M 10x1 p/n 604 17 25
Universal glow plug reamer model R For cleaning the glow plug shaft and the sealing seat in the cylinder head for glow plugs with a thread M10x1 and M10x1,25 with actuator. Universal glow plug reamer for glow plugs with a thread M10x1 and M10x1,25 p/n 604 17 15
Glow plug reamer model III for CDI engines For cleaning the glow plug shaft and the sealing seat in the cylinder head for MB CDI glow plugs M 12x1,25 with actuator and guidance Glow plug reamer model III for CDI engines p/n 604 16 15
Special tap supplement Glow plug tools M10 x 1 assortment 12 pcs Special tap supplement glow plug tools M10 x 1 assortment 12 pcs p/n 604 17 83
B 14
Special thread repair set for glow plug M10 x 1 Special thread repair set for glow plug M10 x 1, 13 pcs. p/n 604 17 85
Set with optional tools to the glow plug drill out toolM10x1 Supplement with optional tools to remove free turning electrode caps, cleaning of the glow plug shaft, sealing the seat in the cylinder head and renewing destroyed threads. Set with optional toolsM10x1 p/n604 18 80
Supplement set uni 3 pcs for glow plugs M10x1
Supplement set uni 3 pcs. for glow plugs M10x1 p/n604 18 85
Glow plug drill out set M12x1,25 Tool kit for drilling and extraction of broken off M12x1,25 glow plugs in MB engines. Glow plug drill out set M12x1,25 p/n 604 17 60 Glow plug drill out set M12x1,25 supplement p/n 604 17 70 supplement to glow plug drill out set M10 x 1
Quick set „G“ For glow plug thread repair M12x1,25 Quick set „G“ For glow plug thread repair M12x1,25 p/n 604 19 05
Thread repair set 10x1 If the M10x1 thread has been damaged in the cylinder head, then this can be renewed with this thread repair set. Thread repair set 7 pcs. for M10x1 p/n 604 18 90
B 15
Glow plugs drilling/extracting tool set model Audi/VW M10x1 With these slim glow plugs frequently the drive hexagon shears off. The central contact of the glow plug is till firmly connected with the glow plug body and prevents the hexagonal from being removed. With this tool in few steps the central contact is removed, the glow plug thread is drilled and the glow plug body is pulled out of the cylinder head. Type: Audi & VW V6 TDI engines with glow plugs M10 x 1 (Except ceramic glow plugs!) Glow plugs drilling/extracting tool set model Audi/VW M10x1 p/n 604 22 000 Suplement set 5 pcs. p/n 604 22 010 with existing sets p/n 604 17 300 / 400
Special puller with 3 jaws and pull nut For pulling stuck glow plugs or remove free turning electrode caps in connection with an impact hammer or the combination sleeve. Special puller with nut and 3 jackets M8/M10/M12 p/n 604 17 97
Impact thread adapter and Impact hammer For pulling stuck glow plugs with an Impact hammer. Impact thread adapter p/n 604 17 98 Impact hammer p/n 103 02 10
Stud puller
To remove from the top broken off central electrodes.
Special production with drive. ¼ " Stud puller 2,5 mm p/n 113 10 25 Stud puller 3,5 mm p/n 113 10 35 Stud puller 4,0 mm p/n 113 10 40 Stud puller 5,0 mm p/n 113 10 55 Stud puller set 4 pcs. p/n 113 00 04
Thread repair sets M8 and M10 For repairing and/or renewing destroyed threads. With the special drill (3 edged, titanium-nitrate) the destroyed thread is removed and the drilling for the threaded insert is produced. Using the turner the cutting threaded insert is then installed. contents Special drill (3 edged, titanium-nitrated) 10 self cutting threaded bushes threaded bush installer
Thread repair set M8 p/n 930 00 80 Thread repair set M10 p/n 930 01 00
B 16
Glow plug socket with universal joint 75 mm long, 3/8" drive
Special long socket for difficult to accessible glow plugs
8 mm p/n 604 71 08 Type: Universal e.g. VW T4 / T5, Opel Z13DT and MB A class.
9 mm p/n 604 71 09 Type: 1,9l CDTI engine in the Opel Vectra C, Signum, Astra H 1,9l JTD engine in the Alfa Romeo 147, 156, GT-, Fiat Stilo 2,4l JTD engine in the Alfa Romeo 166, Lancia Thesis
Glow plug socket 9mm laterally slit This special 9mm socket has a lateral slot to allow it to go around the cable which is fixed to the glow plug so that it will not be damaged Type: Fiat, Alfa, Lancia PSA
Glow plug socket 8 mm with universal joint 8mm 3/8“□ drive 150 mm long This glow plug socket 8mm does not have a magnet, but a retaining ball which holds the glow plug. The joint is approximately in the centre of the socket. Type: VAG, Opel, MB and others. Glow plug socket 8 mm with universal joint p/n 904 71 08
Glow plug ratchet 12mm x 8mm x 245 mm long Slim, bent ratchet. Particularly developed for hard to reach glow plugs, e.g. behind the injection pump. Glow plug ratchet p/n 604 82 20
Glow plug socket Short, slim socket with universal joint and retaining spring. Model 1 3/8" �drive, 12mm. Type : BMW, Fiat, MB, Renault, Volvo et al.. Model 2 3/8" �drive, 10mm Type : Audi/VW TDI, Renault G8 T, Honda MB A class (with angled extension 7312020) Model 4 3/8" �drive, SW 10mm L Type : Opel/ MB CDI Model 5 3/8" �drive, SW 12mm L Type : Universal, e.g.. MB 4 valve Glow plug socket model 1 p/n 604 71 20 Glow plug socket model 2 p/n 604 71 10 Glow plug socket model 4L p/n 604 72 10 Glow plug socket model 5L p/n 604 72 20
B 17
Spark plug socket double joint release pliers 45 6 and 12 mm round, 320 mm long Spark plug socket pliers double jointed for low-lying and hard to access spark plugs. Because of the double joint the pliers need little room to open and seize Type: e.g. MB R classV6 und V8 spark plug socket Spark plug socket double joint release pliers 2 pcs. p/n 604 02 700
Glow plug testing device 11 / 12 V With LED display For testing installed glow plugs with the engine switched off (approx. 15 min.) polarity safe connection to the car battery. Automatic shut off In case of short-circuit, the red LED shines for approx. 2 sec. Glow plug testing device 11 / 12 V p/n 609 98 00
Glow plug testing device GKP 05 For the examination of glow plugs in diesel engines from year of manufacture 2004.
DESCRIPTION: • For 4,4 and 5 V glow plugs • Display by led’s of the condition of the glow plugs good/bad • “Low Battery” display • Automatic shut off • Voltage supply by 9 V compound battery Type: Audi: A2, A3, A4, A6, A8 BMW: 1, 3, 5, and 7 series, X3, X5 Mercedes: A , B , C class, CLK, CLS, E class, GL class, ML class Seat: Alhambra, Ibiza, Leon, Toledo 3 Skoda: Octavia, Roomster VW: Caddy, Crafter, Eos, Golf 5, New Beetle, Passat, Phaeton V6, Polo, Touareg, Touran, etc.
Glow plug testing device GKP 05 p/n 909 98 00
Spark plug socket pliers model 3 Grab pipe 35 mm, length 290 mm For taking off and press on of hard to reach spark plug sockets, in particular for rubber spark plug sockets
Type : Alfa Romeo, BMW, MB, Opel, Ford
Spark plug socket pliers model 3 p/n 604 02 00
Spark plug socket pliers model 6 Special pliers to damage-free taking off and/or press on of spark plug sockets.
Spark plug socket pliers model 6 p/n 604 01 00
B 18
Spark plug torque wrench model ZK 3/8" � drive For controlled fastening of spark plugs with cone sealing seat. Fixed adjusted torque of 25 Nm. Unscrewing by switching as with conventional ratchet. Spark plug torque wrench model ZK p/n 406 10 00
Spark plug socket With spark plug fixing clip. 5/8" (16 mm) x 70 x 3/8" � drive p/n 604 60 20 5/8" (16 mm) x 70 x 1/2" � drive p/n 604 60 40 11/16"(18 mm) x 70 x 3/8" � drive. p/n 604 60 50 11/16"(18 mm) x 70 x 1/2" � drive p/n 604 60 60 13/16"(20,6 mm) x 70 x 3/8" � drive p/n 604 60 10 13/16"(20,6 mm) x 70 x 1/2" � drive p/n 604 60 30
Spark plug joint socket 3/8“ � drive model 1 with fixing clip SW 16 (5/8) x 85 Type : Universal, MB A class V6 Spark plug joint socket model 1 with fixing clip p/n 604 61 20
Injector disassembly tools For removing of seized injectors. With the adapter screwed into upper section of the disassembled injector and then using the impact hammer the injector is removed. Type: BMW CR-Diesel e.g. M57, M47 2,0l in the BMW 320, Citroen etc. Renault Trafic and Master, Opel Vivaro and Movano, Nissan Primastar and Interstar with Renault motor 1,9l dCi, e.c.: F9Q Disassembly adapter p/n 603 84 40 Special inbus socket insert p/n 603 84 17 Slide hammer model 38kg p/n 614 88 00 Injector disassembly tools 3 pcs. p/n 603 84 20
Special inbus socket insert with bore 7,5mm Special inbus socket insert p/n 603 84 171 Injector disassembly adapter Special for Bosch piezo injectors m14 x 1,5 : M18 x 1,5
Injector disassembly adapter piezo p/n 603 84 405
B 19
Injector extractor model dci2,2 hydraulically
For the extraction of seized injectors. This specially designed tool kit allows for mechanical or hydraulic extraction of seized injectors in the following engines:
Type: Renault Motor 2,2/2,5 dCi, e.c.: G9T & G9U in the Espace, Laguna, Master, Vel Satis, Opel Movano, Nissan Primastar, Interstar
Injector extractor model dci2,2 20 pcs. p/n 603 83 95
For the extraction of seized injectors. This specially designed tool kit allows for mechanical or hydraulic extraction of seized injectors in the following vehicles: Type: Renault Megane, Scenic, Laguna, Trafic and Master, Opel Vivaro and Movano, Nissan Primastar and Interstar with Renault Motor 1,9l dCi, e.c.: F9Q
Injector extractor model dci1,9 13 pcs p/n 603 83 36 in a case, complete
Injection nozzle extractor MB CDI engines For the extraction of seized CDI injectors. For use on all MB CDI models including A class, offers both mechanical and hydraulic extraction, with hydraulic extraction on A class models it is necessary to destroy the rocker cover. Injector extraction set Mercedes Benz CDI engines inclusive A class, 15 pcs in a case p/n 603 84 00 Injector extraction set Mercedes Benz CDI engines exclusive A class, 9 pcs p/n 603 84 10
B 20
Supplement set for MB A class 6 pcs p/n 603 84 15 Supplement to p/n 603 84 10 Supplement set 4-tlg. for extremely seized injectors p/n 603 84 45 Injectors extraction spindle M18 p/n 603 84 46 Nut with washer p/n 603 84 47 Support sheet p/n 603 84 49
Support elements for injector extraction set Mercedes Benz CDI engines, 4 pcs p/n 603 83 65
Injector extraction set Mercedes Benz CDI engines 19 pcs p/n 6038370
Injector extraction set For the removal of seized injectors in vehicles using PSA HDI engines type DW10ATED4 and DW12TED4, for mechanical or hydraulic extraction using a 20 tonne open core hydraulic cylinder.
Type: PSA engines DW10ATED4 and DW12TED4 Peugeot, Citroen, Fiat, Suzuki, Ford, Volvo etc Injector extraction set p/n 603 83 305
Injector extraction set Supplement to the existing tool set 30 pcs. p/n 60383305, 5 pcs. for PSA 2 valve engines e.c. DW10 RHY/RHZ (2.0 L / 8V) Type: Citroen, Peugeot, Fiat und Suzuki Injector extraction supplement set 5 pcs. for BOSCH injectors in PSA 2 valve engines DW10 RHY/RHZ p/n 60383320
B 21
Assortment of copper sealing rings 450 pcs
Universal copper injector sealing ring set with 15 different combinations.
This is the optimized version of the cleaning and milling tool set. The advantages are clearly obvious: Can be used with HDi engines, diesel direct injection and common rail engines with BOSCH and DELPHI injectors. Shaft cleaning by brushes with machine drive, sealing seat cleaning with cutter 120° Ø. 21,0mm: 17,0mm stepped, miller 0° Ø. 17,0mm continuous, miller 0° Ø. 19,0mm: 17,0mm: 15,0mm stepped. Universal sealing ring puller for seized sealing rings. Cleaning brush set universal 18 pcs completely with holder, brushes and sealing ring extractor p/n 903 90 30 Cleaning brush set universal 17 pcs completely with holder, brushes without the sealing ring extractor p/n 903 90 40 Specially cleaning brush set 4 pcs with holder ¼ “bit drive 2 brushes and flexible drill holder p/n 903 90 35
Injector sealing seat cleaning & milling set PSA For cleaning and revising the injector shaft of PSA engines With the special brush the injector shaft wall, the sealing seat for the injector and the borehole for the injector nozzle are cleaned. In the case of heavy pollution and/or damage to the sealing seat it is precisely reworked with the milling tool, so that a perfect sealing surface is obtained. Type: PSA engines DW10ATED4 (RHW 2,0l 16V) & DW12TED4 (4HW 2,2l 16V) (Peugeot 407, 806, 807; Citroen C5, C8, Evasion; Fiat Ulysse; Lancia Phedra, Volvo S 40 ( II ), V 50 (new types); Suzuki Vitara, Ford Focus (2,0l 16 V from 2006) Cleaning brush set PSA 16 pcs completely with holder, brushes and sealing ring extractor p/n 903 91 200
Cleaning brush set PSA 15 pcs completely with holder, brushes without sealing ring extractor p/n 903 91 250
B 22
Sealing ring extractor For extracting the seized copper sealing rings from the injector shaft without damaging the cylinder head. Without this tool it is extremely difficult to remove the sealing ring without damaging the sealing seat. With an M10 thread for use with a slide hammer. Type: CDI engines e.g. MB, Opel, Renault engines with 2,2L (MC G9T) + 2,5L (MC G9U) , Nissan und PSA-Engine. Sealing ring extractor p/n 603 90 700
Thread repair set M6 For repairing and/or renewing destroyed aluminium threads e.g. Injector retaining claw thread at the common rail cylinder head. With the special drill (3 edged, titanium-nitrate) the damaged thread is removed and the drilling for the threaded sleeve is produced. The cutting threaded insert is then placed with the turning tool. Type : Aluminium cylinder heads e.g. common rail Contents: Special drill (3 edged, titanium-nitrate) 10 self cutting thread bushes Threaded bush installer Thread repair set M6 p/n 604 17 80
Line key set 10, 11, 12, 13, 14mm hexagon each size as short and long ring spanner 12 point. Special socket 22mm x 3/8" Allows better power transmission and accurate tightening by torque wrench. With special sockets, each in a short and long version (e.g. for deep lying screw connections) this tool can be used for example for air conditioning lines or brake hoses according to specification and/or after manufacturer data. The torque wrench (e.g. 4061000) is applied axially to the screw centre; the torque value is thereby not falsified by an additional lever. Line key set p/n 605 11 50 in a metal case Injector socket model 2 27mm x 1/2" � drive, laterally milled open Internally machined socket For removing leak lines. Type : passenger cars also turbo Injector socket model 2 p/n 605 93 70
B 23
CR injector testing set model Master Diesel resistant Plexiglas block with 6 chambers (each 8 ml) on a chain. 6 silicone hoses each 37 mm long and 4 six-part sets with connectors for Bosch, Delphi, Denso and Siemens injectors. This is universally applicable equipment for examining the CR injector return rate. The return rate quantity of the injectors gives information of the condition of the individual injector e.g. with starting problems or a badly running engine Type: CR injectors from Bosch, Delphi, Denso, Siemens e.g. Ford, MB, Opel CR injector testing set model Master p/n 430 49 20 in a case
CR Injector measuring containers size III 120 ml measuring beakers with 1 m tubes and brass connectors. Containers for the ascertainment of the return rate of CR injectors, e.g. with starting problems or badly running engine. The return rate quantity of the injectors gives information of the condition of the individual injector. Typ: CR-Injectors e.g. Opel, Ford (Delphi system) CR Injector measuring containers size III 6pcs p/n 430 49 35 in a case
CR Injector connectors
Connectors for CR injector test equipment model Master p/n 430 49 20 and measuring beaker size III p/n 430 49 35
Model C1 for Bosch injectors (Standard) 90 ° brass Model C2 for VDO/ Siemens injectors 90° brass Model C3 for Denso injectors 90° brass Model C4 for Delphi injectors 45° plastic
Model C1 (standard) 1 pcs p/n 930 49 36 Model C1 (standard) 6 pcs p/n 930 49 38 Model C2 VDO/ Siemens injectors 1 pcs p/n 430 49 36 Model C2 VDO/ Siemens injectors 6 pcs p/n 430 49 46 Model C3 Denso injectors 1 pcs p/n 930 49 39 Model C3 Denso injectors 6 pcs p/n 430 49 43 Model C4 Delphi injectors 1 pcs p/n 430 49 34 Model C4 Delphi injectors 6 pcs p/n 430 49 39
B 24
Return flow measuring instrument for CR injectors Testing set for Common Rail return flow measurement of up to 6 injectors, applicable independent of engine design and injector manufacturer. Test possibilities: for starting problems a defective injector can be determined. Comparison of the return flow of different Common Rail injectors. Determination of the total return volume. The connection takes place through brass adapters on the return pipe of the injector or directly to the hose on the leakage oil nipple. The standard version is delivered with adapters for Bosch injectors. For other injector manufacturers further adapters are available Return quantities measuring instrument of CR injectors Set with 6 measuring beakers plastic p/n 430 49 06 Set with 4 measuring beakers p/n 430 49 04
CR piezo & Delphi injectors testing set For the examination in the new common rail systems of partly built in piezo and the new Delphi injectors. Different to conventional injectors in that return flow is not tested here for the examination and/or comparison of the injectors, but the pressure in the return system. The pressure ranges which can be measured depend on the injector manufacturer and the pressure specified for the respective engine. The injectors do not have to be removed for examination. The following diagnostic possibilities are given: 1. Defectiveness of the injector 2. Defectiveness of the pressure support valve 3. Bubble-free Diesel return Type: CR piezo injectors of Bosch & Siemens CR Delphi injectors new generation CR piezo BOSCH injectors testing set p/n 430 49 60 CR piezo SIEMENS injectors testing set p/n 430 49 70 CR DELPHI new generation testing set p/n 430 49 80 Common-rail piezo & Delphi injectors testing set complete: 1 manometer, Plexiglas housing and 6 return hoses p/n 430 49 90 CR piezo injectors testing set with a pair hoses for Bosch + Siemens p/n 909 83 50 Single sets: Return hose connectable 2 pcs for Bosch CR-piezo injectors p/n 909 83 25 Return hose connectable 2 pcs for SIEMENS CR-piezo injectors p/n 909 83 05 Return hose connectable 2 pcs for DELPHI new generation injectors p/n 909 83 75
B 25
Digital Common Rail Sensor-und pressure test unit Digital pressure test unit with plug in adapters for the pressure and leakage test of the common rail injection system. The test unit is connected with the plug in adapters (see scope of supply) directly to the common rail pressure sensor. The existing system pressure is displayed and compared with the manufacturing data. Measuring range selectable of a) 0...1500 bar b) 0...1800 bar (resolution of measured values 10 bar). Error recognition by red LED, automatic disconnection after approximately 7 minutes. Voltage supply by 9 V compound battery. Scope of delivery: 1 basic unit CRP 02 1 adaptor cable for Mercedes vehicles 1 adaptor cable universal plug 1 adaptor cable for French and Italian vehicles Digital Common Rail Sensor-und pressure test unit p/n 430 49 00 Supply completely in the sturdy plastic case, without battery
Fuel pipe release pliers These pliers are required for the disassembly of the diesel fuel lines from the diesel filter on Fiat multi-jet engines. For example with the Fiat Grande Punto, Panda, Ducato Idea etc. These engines are also used in Opel and Suzuki vehicles. Fuel pipe release pliers p/n 605 04 200
Battery tester F90 12-24Volt For testing the battery charge and the alternator Battery tester F90 p/n 909 09 00
Steel wire hole brushes with grasp Steel wire brushes for cleaning injector shafts, with a diameter 15.00 mm and 20.00 mm Type: Common Rail diesel engines such as PSA or Renault models, also suited to thinner or thicker shafts in the cylinder head. Steel wire hole brush 15x100 overall length 280.00 mm with wooden grip p/n 903 90 23 Steel wire hole brush 20x100 overall length 280.00 mm with wooden grip p/n 903 90 24 Steel wire hole brushes set 2 pcs 15x100 and 20x100 overall length 280.00 mm with wooden grip p/n 903 90 25
B 26
Stroboscope lamps for petrol and diesel engines Stroboscope lamps for professional use. The slim, pistol-like form allows work in the tightest of engine compartments. Robust construction with an analogue or digital display. Special high speed bulbs produce an extremely bright light. For vehicles with a diesel engine an adapter SKUA 01 is available. For specification see the following table. Supplied in a cardboard box
Gearbox flange socket model 3 36mm x 12 edged x 1/2" drive Type : MB commercial vehicles gearbox G 2/ 24/ 27 Clutch flange MB passenger cars rear axel bearing W 140 Gearbox flange socket model 3 p/n 743 63 60 Hint: Also works with the VW Polo, Skoda Fabia drive shaft from `02
Extractor Krallex model F / S Twin & triple arm Span 25 - 130 mm Extractor arms 150/200/250 mm long Foot thickness 2.0/3.6 mm Outside and interior extractor with slim hooks particularly suitably for small gaps. Because of the different extractor arm lengths and different foot forms is it possible to use this extractor in a wide range of areas. Type : Universal 1 x twin arm bridge 25-130 mm p/n 104 22 20 1 x triple arm bridge 25-130 mm p/n 104 88 80 1 x spindle 210 mm lg. p/n 104 23 20 1 x spindle with transverse grasp 250 mm long p/n 104 98 70 3 x extractor arm size 1 100 mm long, with foot F 2,0 p/n 104 88 91 3 x extractor arm size 2 200 mm long, with foot F 2,0 p/n 104 88 92 3 x extractor arm size 3 250 mm long, with foot F 2,0 p/n 104 88 93 3 x foot Krallex 3,6 thick x 27 mm wide p/n 104 25 55 3 x foot Krallex S 3,6 thick x 14 mm wide p/n 104 25 53 1 x bracket p/n 104 98 95 Extractor Krallex model F / S twin & triple arm p/n 104 98 10 in a steel box
Bearing extractor model K Hooks size 1 thru 3 Bearing nr: 6004 thru 6010, 6200 thru 6205, 6300 thru 6302 Hooks size 4 thru 6 Bearing nr.: 6011 thru 6015, 6206 thru 6211, 6303 thru 6307, 6403 thru 6404. For the disassembly of a range of ball bearing sizes. Because of the different extractor arms, the set of extensions and the adjustable three-arm bridge with a clamping range up to 120 mm it is possible to get optimal adjustment of the extractor. As the extractor grips at three points between the bearing outer race and inner race tilting can be prevented Basic equipment 1 x spindle 1 x three-arm bridge 3 x of attachment pins (hooks) 3 x of attachment pins (extensions) 1 x set of extensions (3 pcs) 2 x thrust piece Bearing extractor model K p/n 610 57 00 Basic equipment in a case with 6 hook sets size 1-6 Bearing extractor model K1 p/n 610 56 80 Basic equipment in a case with 3 hook sets size 1-3 Bearing extractor model K2 p/n 610 56 90 Supplement set, hook sets size 4 thru 6
C 02
Pressure piece set ALU Versatile pressure piece set made from aluminium. The installation forces are transferred evenly and carefully so that damage to ball bearings, sockets, shaft seals etc are avoided. For use with a rubber or plastic hammer Contents: 1 handle 120 mm long with retaining screw 9 pressure pieces with outside Ø: 40/ 44/ 50/ 59/ 63/ 65/ 72/ 76/ 81 Pressure piece set ALU 10 pcs p/n 614 45 30
Transmission bearing ring extractor This set of special inner bearing extractors and slide hammer are used for extracting the diagonal roller bearing outer rings from the transmission case. Type: Renault: Master, Trafic, Espace, Laguna Opel: Movano, Vivaro Nissan: Interstar, Primastar Inner bearing extractor 6A p/n 104 96 61 Inner bearing extractor 7A p/n 104 96 71 Slide hammer 700 g p/n 103 02 10 Adapter 3/8“ inner – ½“ outer p/n 904 96 05 Transmission bearing ring extractor 4 pcs p/n 910 17 00 Optional: For Renault gearbox PK1: inner bearing extractor 51-E7 40-75 mm with 3 jackets p/n 104 96 96 Counter support size 2 p/n 105 01 20
Ball bearing extractor For ball bearings, which sit on the axel or in the housing and thus can not be seized from the outside or by the hole. Type: ISO bearing series nr 6000 - 6012, 6200 – 6212, 6300 – 6310, 6403 – 6410 Ball bearing extractor p/n 107 00 00
Pliers for retaining rings without grab holes For Renault vehicles this is a special pliers for the disassembly and assembly of the snap ring in the transmission case which secures the transmission shaft into the exit port. There are two different snap ring types: a weaker snap ring in all JC transmissions, such as the JB and JR transmission, and a strong, more solid ring in the transmissions PK1, PK6 and PF1, PF2. Pliers for retaining rings without grab holes p/n 910 33 40
C 03
Clutch centring tool model 3 For centring clutches that do not have a crankshaft guide bearing. Type : passenger car universal Clutch centring tool model 3 p/n 611 85 00
Oil pan repair combination set M 13 , 15 , 17 x 1,5 For the repair of defective oil drain plug threads. The defective threads are removed with the threaded tap and extended to the next size. before/after M12 = 13 M14 = 15 M16 = 17 Type : Universal, e.g. Audi, VW, BMW, Ford, Opel 1 x tap M 13 x 1,5 1 x tap M 15 x 1,5 1 x tap M 17 x 1,5 3 x screw M 13 x 1,5 6 x screw M 15 x 1,5 long 3 x screw M 15 x 1,5 short 3 x screw M 17 x 1,5 With copper sealing rings Oil pan repair combination set p/n 912 55 00 in a plastic case
Oil pan repair set model 1, 2 & 3 For fast and low-priced repair of defective oil drain plug threads in the oil pan. Each set consists of one tap and 16 spare screws with sealing rings in a plastic case. Tap M 15 x1,5 p/n 612 51 00 12 x screw M 15 x 1,5 x 24 with sealing ring p/n 612 51 50 Oil pan repair set model 1 p/n 612 52 00
Tap M 15 x1,5 p/n 612 51 00 4 x screw M 15 x 1,5 x 24 with sealing ring p/n 612 51 50 4 x screw M 15 x 1,5 x 16 with sealing ring Oil pan repair set model 1a p/n 912 11 00 Tap M 17 x 1,5 p/n 612 52 50 16 x screw M 17 x 1,5 x 16 with sealing ring p/n 612 51 70 Oil pan repair set model 2 p/n 612 53 00 Tap M 13 x 1,5 p/n 612 50 80 12 x screw M 13 x 1,5 x 16 with sealing ring p/n 612 51 30 Oil pan repair set model 3 p/n 612 54 00 Refilling packs sealing rings: M 13 Copper (10 pieces) p/n 612 51 60 M 15 Copper (10 pieces) p/n 912 12 00 M 17 Copper (10 pieces) p/n 612 51 75 M 13 Aluminium (10 pieces) p/n 612 51 33 M 15 Aluminium (10 pieces) p/n 612 51 61 M 17 Aluminium (10 pieces) p/n 612 51 79 Spare screws M15 x 1,5 x 16 (packing unit 5pcs) p/n 912 10 50 Spare screws M15 x 1,5 x 24 (packing unit 5pcs) p/n 912 11 50
C 04
Oil pan repair set model 4 M 20 / 24 x 1,5 For the repair of defective oil drain plug threads. The defective threads are removed with the threaded tap and extended to the next size. Before /after M18 = 20 M22 = 24 Type : Alfa Romeo, Fiat, Lancia und Volvo
Tap M 20 x 1,5 p/n 612 56 50 5 x screw M 20 x 1,5 p/n 612 56 60 Copper sealing rings M 20 (10 pieces) p/n 612 56 75 Aluminium sealing rings M 20 (10 pieces) p/n 612 56 85 Tap M 24 x 1,5 p/n 612 57 50 5 x screw M 24 x 1,5 p/n 612 57 60 Copper sealing rings M 24 (10 pieces) p/n 612 57 75 Aluminium sealing rings (10 pieces) p/n 612 57 85 Oil pan repair set model 4 p/n 612 56 00 in a case Additional individual sets in a case: Contain tap and 10 screws, sealing rings aluminium & sealing rings copper Oil pan repair set model 4a M 20 x 1,5 p/n 612 56 10 Oil pan repair set model 4b M 24 x 1,5 p/n 612 56 20
Oil service socket 10mm � drive x 1/2" � drive Type : Ford Sierra, Granada diesel engine, Peugeot, Volvo V 6, Opel Frontera 8mm � drive x 3/8" � drive Type : Peugeot, Volvo 264, Renault all from `83 Nissan Micra 1,5 D till `98 Opel Vivano Oil service socket 10 � p/n 612 03 20
Oil service socket 8 � p/n 612 03 30
Oil service key set Specially hardened set of keys for the disassembly and assembly of most normal oil drain plugs.
Adapter 1/2" � drive for the acceptance of the inserts p/n 612 21 00 Insert size 1 8 mm x 3/8" hexagon p/n 612 20 10 Insert size 2 10 mm x 11 mm hexagon p/n 612 20 20 Insert size 3 12 mm x 13 mm hexagon p/n 612 20 30 Insert size 4 14 mm x 17 mm hexagon p/n 612 20 40 Insert size 5 8 mm x 3/8" square p/n 612 20 50 Insert size 6 19 mm x 17 mm hexagon p/n 612 20 60 Oil service key set 7 pieces in a metal box p/n 612 20 00
Universal oil service socket set This 17 piece universal oil service socket set offers along with triangular, square and hexagonal and many other required variants, all have a 3/8 “ drive .
Universal oil service socket set 17 pieces special sizes p/n 9122010
C 05
Oil filter spanner model F
For oil filter 60 - 110 mm Ø.
With one handed operation this tool is ideal for hard to reach oil filter
housings.
Oil filter spanner model F p/n 612 18 00
Spare band p/n 612 18 50
Oil filter chain with joint Type : Universal 60 – 110mm Oil filter chain with joint p/n 910 12 00
Oil filter spider 3/8" � and 19mm hexagon drive
Step less adjustment from 60 to 120 mm Ø. Oil filter spider Mod. US p/n 612 00 20 Alternatively: 1/2"� and 21mm hexagon drive Step less adjustment from 63 to 102 mm Ø Oil filter special spider p/n 912 00 30
Oil filter key model G For easy loosening of oil filters possible even in the tightest of engine compartments Oil filter key 65 - 80 mm Ø p/n 912 00 00 Oil filter key 80 - 100 mm Ø p/n 912 00 10 Oil filter special key assortment 3 pcs Three most popular oil filter keys in a particularly short version with
1/2"� drive and 21mm hexagonal. Sizes are 27, 32 and 36mm each with an overall height of 32 mm. Special Oil Filter key assortment 3 pcs p/n 912 08 75
Oil filter key for Haldex clutch 46mm 12 sided. x 390 mm long For the disassembly/assembly of the oil filter on the Haldex clutch allows easy access to this difficult to reach filter. Type : VW 5 /6 speed gearbox 4WD , in the Golf IV, Bora, Sharan, Skoda Octavia Oil filter key Haldex clutch p/n 611 96 50
Steering wheel puller model GM
Span width 90 mm, span depth 87 and 135 mm
Type: Opel passenger cars with standard and sport steering wheels.
Steering wheel puller model GM p/n 106 20 20
Spare parts: Replacement hooks 135 mm long p/n 106 24 20 Replacement hooks 87 mm long p/n 106 24 10 Spindle 200 mm long. p/n 104 57 30
Steering wheel puller model D trucks Four legged steering wheel puller for trucks with 2 sets of spindles size M 8 + M 10. Type : MB (e.g. DB 1632) and Iveco Steering wheel puller model D trucks p/n 106 36 00
C 07
Steering wheel spacer puller. Total length 75 mm, 42 mm Ø. For removing the spacer from the steering column on VAG vehicles. The spacer must be pulled, when the ignition switch is renewed. The puller is put over the spacer and locked with a clamping sleeve. The spacer can now be pulled off over the spindle. Type : Audi / VW, Seat
Steering wheel spacers puller p/n 617 15 00
Ball joint separation fork. For the release of ball joint pins on automobiles, land and construction machines, hydraulic plant and large machinery. Model Fork opening Overall length SizeT3* 18 mm 300 mm p/n 106 40 30 SizeT4 29 mm 300 mm p/n 106 40 40 SizeT5 39 mm 350 mm p/n 106 40 50 SizeT6 45 mm 350 mm p/n 106 40 60 Hint*: BMW E36 front axle ball joint.
Ball joint extractor model T 1 Fork opening: conical 18-22 mm. For fast and undamaged extraction of ball joints in the suspension and steering. Ball joint puller model T1 p/n 106 40 10
Ball joint/ball pin ejector Model T11 - T12 For safe ejection of the swivel joints from the stub axle and steering arm (wishbones and McPherson struts). Model T11 Fork opening 20 mm, clamping range 12 - 50 mm Type : Opel front wheel drive, Ford passenger cars, Transit, VW, Audi 80 / 100 / 200, Transporter, BMW, MB, Citroen (except CX), Renault, Fiat, all Japanese, Honda (ball joint) commercial vehicles (shift linkage) Model T11P Fork opening 24 mm, clamping range 12 - 50 mm Type : Audi A 4/ 6 /8, Opel Movano, Porsche, Renault Master Model T11 MB with slot Type : MB W203 and 210 Model T12 Fork opening 20 mm, clamping range 50 - 80 mm Type : Opel Omega A/B, Senator, VW-Transporter Model T 11 p/n 106 45 00 Model T 11P p/n 106 45 70 Model T 12 p/n 106 46 00 Model T11 MB with slot p/n 106 45 80
C 08
Ball joint ejector model SP1 commercial vehicles For ball joint -Ø : 27 - 36 mm Rate of cut max. : 90 mm workshop-tested, heavy version for high strain Type : e.g. MB Atego till 18t, MAN, Iveco, Renault, Scania, Volvo, DAF Model SP 1 with mechanical spindle Spindle and anvil are exchangeable depending upon the space required. Model HS 1 with 12 tonne hydraulic spindle Improved power with the 12 tonne hydraulic spindle. Model HZ 1 with 10tonne hydraulic cylinder. Faster, safer and easier to use, with quick coupler for use with our hydraulic hand pump, connector and hose. Model SP 1 with mech. spindle p/n 106 44 30 Model HS 1 with hydraulic spindle 12t p/n 106 44 40 Model HS 1 without hydraulic spindle 12t p/n 106 44 39 Model HZ 1 with hydraulic cylinder 10t p/n 106 44 45 Model HZ 1 without cylinder p/n 106 44 44
Ball joint ejector for commercial vehicles For ball joint Ø : 35-45mm Rate of cut max. : 115 mm
workshop-tested, heavy version for high strain Type: MB Actros, Atego from 18t, SK MAN F 2000, TG, low-floor vehicle Iveco Euro Star, Tech, Turbo-Star Renault, Scania, Volvo, DAF
Model SP with mechanical spindle. Spindle and anvil are exchangeable depending upon the space required.
Model HS with hydraulic spindle 12t Improved power with the 12 tonne hydraulic spindle
Model HZ with hydraulic cylinder 10t Faster, safer and easier to use, with quick coupler for use with our hydraulic hand pump, connector and hose.
Model SP with mech. spindle p/n 106 43 30 Model HS with hydraulic spindle 12t p/n 106 43 40 Model HZ with hydraulic cylinder. 10t p/n 106 43 50 Model HZ without cylinder p/n 106 43 49 Hydraulic flat cylinder 10t p/n 802 51 60
With strong spring release and SW quick-coupler.
C 09
Ball joint extractor universal Fork opening of 22,0 mm quadruple adjustability. This high-quality, solid universal extractor is characterised by the possibility for quadruple elevation adjustment. This puller is adjustable in the height on 24,0 - 30.0 - 40.0 - 45.0 mm. and has a fork opening of 22,0mm and a overall length of 155,0mm Ball joint extractor universal p/n 906 46 00
Ball joint ejector model T 8 For ejecting the ball joint from tie rods etc. Allows for safe and simple operation.
Size Fork opening Clearance Headroom 1 18 mm 40 mm 35 mm p/n 106 42 80 2 25 mm 50 mm 45 mm p/n 106 42 90 3 29 mm 60 mm 55 mm p/n 106 43 00 4 40 mm 80 mm 80 mm p/n 106 43 10 5 46 mm 90 mm 100 mm p/n 106 43 20
Ball joint ejector For ejecting the ball joint from track rods, hubs and stabilisers etc. Particularly suitable where there is little space.
Size 1 fork opening 23 mm Type : Audi, VW, BMW, Citroen Jumper, Fiat Ducato, Ford, MB e.g. 202, 210, Opel, Peugeot Boxer, Renault, Rover, SAAB, Volvo, Japanese passenger cars
Size 2 fork opening 28 mm Type : Audi A4, A6, A8, VW Passat from `97, MB
Size 3 fork opening 34 mm Type : MB Sprinter, VW LT
Ball joint ejector model B 26 mm fork opening, 45 mm clearance With a slim at the rear open construction for ejecting ball joints from stub axles and track rods. Type: BMW E 46 et al. Ball joint ejector model B p/n 106 44 80
C 10
Fixing thorn sub frame For fixing the sub frame e.g. during oil pan disassembly, silent bearing change or accidental damage for which the sub frame must be moved and/or dismantled.
Thereby is partially an otherwise necessary wheel alignment void. Model 1 2-tlg. p/n 617 44 80 Type : Audi A4 / A8, A6 from 97´, Passat from `97
Universal spur measuring setting jig. Also suitable for small panel vans For fixing the „Spur“ (toe in – toe out) on track rods during repair to the stub axle or when replacing the track rod ball joint Type : passenger cars and small panel vans Universal spur measuring setting jig set 12 pcs.p/n 917 45 50
Track rod spanner Two sets with two tie rod keys and a 1/2" square drive available in sizes 17 and 22 mm Track rod special spanner 1/2" drive 17 p/n 917 20 00 Track rod special spanner 1/2" drive 22 p/n 917 22 20
Track rod spanner set With 7 spanner inserts ( 14, 17 & 33,6mm, 3/16”, 1 1/4” ,1 5/16” & 1 7/16”) for operation of the internal tie rod nut. Track rod spanner set p/n 917 30 00 Extra spanner inserts Spanner insert 27mm p/n 917 27 00 Spanner insert 32mm p/n 917 32 00 Spanner insert 34mm p/n 917 34 00 Spanner insert 38mm p/n 917 38 00
D 01
Spring compressor with basic equipment Max. 2300 Kg bracket set 80-160mm + bracket set 140-195mm Due to its large clamping range this extremely sturdy spring compressor set with newly developed spring brackets is suitable for most passenger car and vans with conventional vehicle springs. This is a highly cost effective tool as the versatility negates the requirement to purchase additional clamps for the tool The set comprises of the basic device with a maximum capacity of 2.300 kg, as well as 2 spring brackets for spring diameters of 80 - 160 mm and 140 - 195 mm. The spindle in the basic device can be operated with an impact gun. The spring brackets are coated with plastic. Brackets are also available suitable for conical springs. Ball springs can also be clamped. With a clamping force of max. 2,300 kg and the employment of a bracket adapter in connection with the standard bracket it is possible to clamp the new asymmetrical suspension of e.g.: VAG, BMW, MB etc. Further technical data and detailed application lists can be found in the enclosed operating instructions. Spring compressor set for McPherson shock struts with 2 pair coated spring brackets, tensile force max 2.300 Kg p/n 915 93 20 Spring compressor basic device round McPherson shock struts, tensile force max 2.300 Kg p/n 915 93 00 Spring brackets size 3 plastic coated for 2,3 t basic device 80 - 160mm application range, double support function p/n 915 93 56 Spring brackets size 5 plastic coated for 2,3 t basic device 140 - 195mm application range, double support function p/n 915 93 58 Spring bracket adapter one piece plastic coated for 2,3 t basic device asymmetric suspensions like e.g.: VAG, BMW, MB p/n 915 92 65
D 02
Spring compressor model P22 Max Tension. 22.500N, GS and TÜV tested. Total length with SW 27 drive hexagon 480 mm Span ca. 340 mm This spring compressor is designed for extremely high loads and is delivered with 2 pairs of standard spring brackets. Suitable for use on the majority of modern motor vehicles. The maximum tension is determined specific to the new generation of vehicles, e.g. AUDI, BMW and MB. For the protection and better grip of the springs the spring brackets are made from special cast steel which is plastic-coated. Examples of use Size bracket II Audi, BMW, Daihatsu, Fiat, Ford, Honda, Hyundai, Mazda, Mitsubishi, Nissan, Opel, Rover, Seat, Skoda, Subaru, Suzuki, Toyota, VW III Audi, Citroen, Daihatsu, Fiat, Ford, Honda, Hyundai, Kia, Mazda, , Mitsubishi, Nissan, Opel, Peugeot, Renault, Rover, Saab, Seat, Subaru, Toyota, Volvo, VW V Audi, BMW, Citroen, Fiat, Ford, Honda, Hyundai, Kia, Mazda, MB, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Rover, Saab, Seat, Skoda, Subaru, Suzuki, Toyota, Volvo, VW VII Renault, Toyota X conical and ball springs - Audi, Chrysler, Citroen, Fiat, Ford, Hyundai, Kia, Mazda, Nissan, Opel,
Peugeot, Saab, Seat, Toyota, VW
Spring compressor basic device 22.500N p/n 615 93 00
Spring bracket size III (pair) 100-155 mm p/n 615 93 56
Spring bracket size V (pair) 155-200 mm p/n 615 93 58
Spring compressor standard 22.500N p/n 615 93 20
With 2 pair brackets ( size. III/V )
Accessories: Spring bracket size II (pair) 80-120 mm p/n 615 91 90 Spring bracket size VII (1 pcs) 180-235 mm p/n 615 93 59 Spring bracket size VIII/IX (pair) Peugeot p/n 615 92 40 Spring bracket size X (1 pcs) 150 mm, conical springs p/n 615 91 15 Spring bracket size XI (1 pcs) BMW E39/46 (top) p/n 615 92 65 Additional the bracket size V is needed. Spring bracket size XII (1 pcs) MB C class (top) p/n 615 92 70 A-/E-/ M class, additional the bracket size V is needed. Spring bracket size XIII (1 pcs) MB E class 211 (top) p/n 615 92 80 Additional the bracket size II is needed. Spring bracket size IX (pair) left spiral Chrysler Voyager p/n 615 92 95 Repair set RP22 spindle, thread block, rivet, p/n 615 93 10 hexagon nut, guard pin
D 03
practice
Spring compressor model PK GS tested Tension force 15000N, span 280 mm With plastic-coated hooks for the disassembly/assembly of coil springs on the vehicle. Simple assembly with plastic coated safety loop and a wedged security hook. Type : Universal, e.g. Opel Vectra C front axle Spring compressor model PK p/n 106 11 00
Shock absorber spanner model 2 5,1 and 6,1 mm flat / oval The moveable grip can move along the central tube. So the key does not have to be changed when there is little room around the shock absorber. Type : Universal
Shock absorber spanner model 2 p/n 620 00 30
Draw hook UNI Thread; M 18 x 1,5 Headroom: approx. 110 mm Hook width: approx. 28 mm Weight: 2.34 kg Solid draw hook applied with our 5kg or 8kg slide hammers. The draw hook is very versatile and can be used e.g. for separating connections such as ball joint (wishbone)/wheel bearing housing or shock strut/wheel bearing housing as well as rough alignment work. Type: Universal e.g. Ford Mondeo, MB Vito front axle Draw hook UNI (without slide hammer) p/n 953 55 30 Slide hammer 5 kg p/n 614 87 90 Slide hammer 8 kg p/n 614 88 00
Spring compressor MB Spring compressor for MB 123, 124, 126, 140, 201, 202, 210 Consists of the basic device with 2 pairs of holders Spring compressor MB p/n 615 65 00
Separation tool kit shock absorber out of the knuckle Renault Megane II 8 pcs Separation tool kit for simple separation of the shock absorber from the knuckle on the Renault Megane II Separation tool kit 8 pieces p/n 921 40 00
D 04
practice
Basic device U 14 Basic device for the fast professional and damage free replacement of bushes, bearings and ball joints. Used with either a hydraulic spindle or hydraulic cylinder this versatile tool can be used on a large number of vehicles.
Basic device without attachments p/n 614 91 01 Restrictor insert p/n 614 91 43 Safety cable 1000 mm p/n 802 51 15 Basic device U 14 - base p/n 614 91 00
a) basic device model U 14 S with 12t hydraulic spindle Due to the 10 mm spindle stroke this variant is particularly suitably for the change of ball joints.
The hydraulic spindle is also used in different wheel hub extractors. (6146850 und 6148679).
* Basic device base p/n 614 91 00 *Thread adapter for hydraulic spindle p/n 614 91 41L 12t hydraulic spindle with thrust piece p/n 104 16 500 Basic device model U 14 S p/n 614 91 05 * Basic device without hydraulic spindle p/n 617 54 05
b) basic device model U 14 H with 12t hydraulic open core cylinder The reliable 12t hydraulic open core cylinder with a stroke of 42 mm is equally suitable for ball joints, bushes and wheel bearings*. To operate the hydraulic cylinder a hand pump, hydraulic hose and hose adapter must be used. * Additional requirement: wheel bearing spindle p/n 614 71 40
Basic device base p/n 614 91 00 12t adapter for hydraulic open core cylinder p/n 614 91 47 12t spindle 3 pcs for hydraulic open core cylinder p/n 617 60 80 Hydraulic open core cylinder 12t p/n 802 51 00 Basic device model U 14 H p/n 614 91 10
Hydraulic adapter model P12 p/n 614 91 49 When using the 12t cylinder with the basic device made by the company Paschke. The pressure spindle p/n 6176080 must be used.
D 05
Ball joint removal and replacement sets These ball joint removal and replacement sets can are specific to the basic device U14
Model 2A Type : MB 211, 220 Supporting sleeve p/n 614 89 31 Press out bolt p/n 614 89 32 Press in sleeve p/n 614 89 33 Support disk p/n 614 89 34 Press piece set model 2A, 4 pcs p/n 614 89 30
Model 3 Type : Renault Laguna Press out bolt p/n 614 90 61 Press out sleeve p/n 614 90 62 Press in sleeve p/n 614 90 63 Press in bolt p/n 614 90 64 Press piece set model 3, 4 pcs p/n 614 90 60
Model 5 Type : MB Sprinter, VW LT from 97 Support sleeve p/n 614 90 71 Press piece A p/n 614 90 72 Press in sleeve p/n 614 90 73 Support ring E p/n 614 90 74 Press piece set model 5, 4 pcs p/n 614 90 70
Model 6 Type : VW T4 Support sleeve p/n 614 90 91 Press piece A p/n 614 90 92 Press in sleeve p/n 614 90 93 Press piece E p/n 614 90 94 Press piece set model 6, 5 pcs p/n 614 90 85
Model 7 Model 7a Type :Opel Movano, Renault Master bottom control arm
Model 7b Type :Opel Movano, Renault Master top control arm
Model 7a Support sleeve A p/n 614 94 56 Press piece A p/n 614 94 57 Press piece E p/n 614 94 58 Support sleeve E p/n 614 94 59 Press piece set model 7a, 4 pcs p/n 614 94 65 Model 7b Press piece A p/n 614 94 51 Support sleeve A p/n 614 94 52 Support sleeve E p/n 614 94 53 Press piece E p/n 614 94 54 Press piece set model 7b, 4 pcs p/n 614 94 60 Press piece set model 7a&b, 8 pcs p/n 614 94 70
D 06
Model Type : PSA 106, 206, AX, Saxo Combined press piece p/n 614 90 21 Countermove support sleeve p/n 614 90 22 Press in piece p/n 614 90 23 Press piece set for ball joints 3 pcs p/n 614 90 20
Press piece set bushes For changing the bushes on the front and rear axles without the need to dismantle the axle. Press piece sets I to VI are only suitable for use with the specified basic device U14. Type : Audi, VW with front wheel drive Press piece rear axle Type : Golf III from `92 rear axle Here for recommended basic devices: p/n 617 54 40, p/n 617 55 00 U-Profile p/n 617 51 01 Press piece E p/n 617 51 05 Press bolt p/n 617 51 07 Press piece A p/n 617 51 09 Guiding sleeve p/n 617 51 08 Allen key 5 p/n 525 20 50 Press piece set VIa p/n 617 51 00
D 07
Bush and bearing set universal Universal tool kit for the removal and replacement of bushes, hydraulic bearings, sockets, ball bearings, shaft seals etc. Dependent upon the requirement the individual sleeves can be modified (e.g. cut outs can be added). As well as being used with the spindles supplied it can also be used on the workshop press. Contents: 4 stepped disks Nr. 1 size 34, 42, 50, 58, 66 Nr. 2 size 36, 44, 52, 60, 68 Nr. 3 size 38, 46, 54, 62, 70 Nr. 4 size 40, 48, 56, 64, 72 4 spindles M 10, 12, 14, 16 8 x press nuts M10, 12. 14, 16 20 press sleeves Ø inside/outside Ø inside/outside 34 / 44 54 / 64 36 / 46 56 / 66 38 / 48 58 / 68 40 / 50 60 / 70 42 / 52 62 / 72 44 / 54 64 / 74 46 / 56 66 / 76 48 / 58 68 / 78 50 / 60 70 / 80 52 / 62 72 / 82 Type: Universal Bush and bearing set universal 36 pcs p/n 617 69 30
36 pcs universal bush and bearing kit with 12.9 quality spindles Universal 36 pcs bush and bearing kit with 12.9 quality spindles p/n 914 46 50
Supplementary 13 pc set of 12.9 quality spindles, nuts and adapters for press and drawing sleeve set Draw adapter M10 p/n 91445400 Draw adapter M12 p/n 91445402 Draw adapter M14 p/n 91445404 Press nut M12 p/n 91446560 Press nut M14 p/n 91446570 Press nut M16 p/n 91446580 Spindle 12.9 M10 p/n 91446510 Spindle 12.9 M12 p/n 91446520 Spindle 12.9 M14 p/n 91446530 Spindle 12.9 M16 p/n 91446540 Supplementary 13 pc set of 12.9 quality spindles, nuts and adapters for press and drawing sleeve set p/n 914 45 500
D 08
practice
Rear bush toolkit model RL rear axle For the removal and replacement of the bushes in the rear axle of the Renault Laguna II. For alignment of the bushes (left/right) an assembly jig can be included in the set. The tool can be operated both mechanically and hydraulically. For hydraulic operation our 12t hydraulic open core cylinder p/n 8025100 (not contained in the set) must be used. Type: Renault Laguna II Bush toolkit model RL 8 pcs p/n 617 64 35 without assembly jig in a case Rear bush toolkit model RL 9 pcs p/n 617 64 20 complete with assembly jig in a case
Bush tools model N1 supplement for commercial vehicles Supplement to bush toolkit p/n 6175350. For the new bush (Ø 68, 00 mm) in the leaf spring eye. Type: MAN Bring in funnel nr. II p/n 617 53 56 Drawing in disk nr. II p/n 617 53 57 Bush tools model N1 supplement 2 pcs p/n 617 53 58
Bush tools model N2 supplement for commercial vehicles Supplement to silent bush toolkit p/n 6175360. To change the following original slotted bushes: Nr. 1 p/n 000 322 1285 Nr. 2 p/n 000 325 0785 ZGS 002
Type: MB, e.g.. Leaf spring eyes
Bring in funnel nr. 1 Ø 59,7 mm p/n 617 53 68 Drawing in disk nr. 1 p/n 617 53 69 Bring in funnel nr. 2 Ø 60,8 mm p/n 617 53 66 Drawing in disk nr. 2 p/n 617 53 67 Bush tools model N2 supplement p/n 617 53 70
Bush tools axle suspension commercial vehicles For the disassembly/assembly of the stabilizer bush using the workshop press.
Type: MB Actros front axle suspension new bush with Ø 75 mm
Drive shaft socket 77 x 1/2" � drive 30mm x hexagon. Type : Universal 30mm x twelve-point Type : Audi, Opel, Renault VW Golf III, Vento u. Passat VR 6 36mm x twelve-point Type : VW Polo (9 N) Socket 30mm x hexagon. p/n 742 63 00 Socket 30mm x twelve-point. p/n 743 63 00 Socket 36mm x twelve-point. p/n 743 63 60 Axle nut socket Type : for Ford Transit from `91, axle nr. 34 2 1/4" (57mm) - twelve-point 3/4" � drive p/n 752 57 00 Type : IVECO 65mm twelve-point 1" � drive p/n 762 65 00
Drive shaft socket set 1/2" drive Special thin walled impact sockets and one-piece socket hexagon inserts. Hexagon inserts 14mm x 43 mm long p/n 610 34 91 Hexagon inserts 17mm x 43 mm long p/n 610 34 92 Hexagon inserts 19mm x 43 mm long p/n 610 34 93 Socket 27mm twelve-point x 85 mm long x Ø 42 mm p/n 610 34 98 Socket 30mm twelve-point x 85 mm long x Ø 42 mm p/n 610 34 94 Socket 32mm twelve-point x 85 mm long x Ø 42 mm p/n 610 34 95 Socket 34mm twelve-point x 85 mm long x Ø 42 mm p/n 610 34 97 Socket 36mm twelve-point x 85 mm long x Ø 42 mm p/n 610 34 96 Drive shaft socket set 8 pcs p/n 610 34 90
Drive shaft socket set 1/2" drive Special thin walled impact sockets and one-piece socket hexagon inserts. Socket hexagon inserts; 14, 17 & 19mm Sockets; 30, 32 & 36mm Drive shaft socket set 6 pcs p/n 614 60 00
D 10
Drive shaft sockets 1/2" drive Special thin walled impact socket. Type: PSA Socket 35mm hexagon x 85 mm long x Ø 47 mm p/n 794 23 50 Socket 36mm hexagon. x 85 mm long x Ø 47 mm p/n 794 23 60
Drive shaft separating tool Helpful tool for taking off and/or separation of the constant velocity joints from the drive shaft of passenger cars with front wheel drive. High time saving while exchanging the gaiter, no impact damage by striking with hammers, universally applicable. Patented tool recommended in the SEAT/VW data base Drive shaft separating tool "VAG" p/n 910 33 55 Drive shaft separating tool Type : Audi, VW, Seat and Skoda For dividing the drive shafts held by a necked-down bolt. The drive shaft joint separation tool is operated by the 12 tonne hydraulic spindle (p/n 104 16 50). Pressure piece size 2 diameter 10,0 mm p/n 610 33 39 Pressure piece size 1 diameter 8,0 mm p/n 610 33 41 Thread insert M14 x 1,5 p/n 610 33 42 Thread insert M16 x 1,5 short p/n 610 33 43 Thread insert M16 x 1,5 long p/n 610 33 46 Basic device sleeve with support p/n 610 33 44 Drive shaft separating tool set 6 pcs p/n 610 33 40 Set 6 pcs as above p/n 610 33 40 12 tonne hydraulic spindle p/n 104 16 50 Drive shaft separating tool set 7 pcs incl. hydr. spindle p/n 610 33 45
Circlip squeezing pliers 285 mm long. For pretension of the drive shaft circlip when assembling the outer joint. The snap ring which is pretensioned by the pliers strengthened spring ensures a fast and damage-free assembly of the joint Type : Audi, VW, Ford, Honda, Mazda, Mitsubishi, Nissan, Opel, Seat, Skoda, Subaru, Suzuki, Toyota, etc. Circlip squeezing pliers. p/n 610 33 30
D 11
Hose band pliers model DR. For CV boot hose clamps made from stainless steel on the drive shaft. The pliers have a 1/2" square in both handles for the use with an extension tool or torque wrench. Effective relationship 1:3,4. Type : e.g. Audi, Opel, VW Hose band pliers model DR p/n 122 65 00
Hose band pliers model o. O. For "earless" clips , e.g. at drive shaft seals, coolant and fuel hoses. Due to the fine points these special hose clips can be installed problem-free with these pliers.
Type : e.g. Audi, VW, MB, Toyota
Hose band pliers model o. O. p/n 122 65 50 Hint: Retaining clip of the air cleaner Opel Astra
Drive shaft retraction nuts Impact nuts with connection thread M 18 x 1.5 M 22 x 1, M 18 x 1.5, M 22 x 1.5, M 20 x 1, M 24 x 1.5, M 20 x 1.5, M 27 x 1.5, M 20 x 1.25, M 30 x 1.5. To retract the drive shaft with our slide hammer p/n 6148790/95 or hub extraction flanges p/n 6148725/6148685 Application sample Thread protection during the disassembly of the drive shaft from the wheel hub and for transmission lateral loosening of the drive shaft. For dividing and separating the often very tight joint; the advantage is that there will be an even and horizontal draw. For retracting the precisely fitting drive shaft teeth into the wheel hub until the hub nut can be fitted Drive shaft impact nut size 0 M16 x 1,5 p/n 610 33 06 Drive shaft impact nut size 1*M18 x 1,5 p/n 610 33 08 Drive shaft impact nut size 2*M20 x 1 p/n 610 33 10 Drive shaft impact nut size 3*M20 x 1,5 p/n 610 33 15 Drive shaft impact nut size 4*M20 x 1,25 p/n 610 33 25 Drive shaft impact nut size 5*M22 x 1 p/n 610 33 33 Drive shaft impact nut size 6*M22 x 1,5 p/n 610 33 35 Drive shaft impact nut size 7*M24 x 1,5 p/n 610 33 37 Drive shaft impact nut size 8*M27 x 1,5 p/n 610 33 38 Drive shaft impact nut size 9*M30 x 1,5 p/n 610 33 47 Retract spindle with nut* p/n 610 32 80 Adapter/ housing with bearing* p/n 610 32 83 Drive shaft impact nut sizes 1 till 9, 9 pcs p/n 610 33 07 Drive shaft retraction nuts 11 pcs.* p/n 610 33 20
D 12
Transmission shaft extractor Type : Fiat Ducato Transmission shaft extractor p/n 611 84 00
Thread cut nuts set
32mm hexagon drive
For the re-cutting of damaged threads on drive shafts.
Contents:
M 20 x 1,25 M 22 x 1
M 20 x 1,5 M 22 x 1,5
13/16" x 20 M 24 x 1,5
3 /4" x 20 M 24 x 2
Type : Universal
Thread cut nuts set 8 pcs. in a plastic box p/n 276 50 00
Disassembly tool kit for VAG models For the disassembly of the bolted wheel hub bearing unit and the drive shaft. Combined disk p/n 916 94 74 Support tube p/n 916 94 73 3 screws M14x1,5x60 10.9 with washers p/n 614 87 285 Adapter 1 1/2“ 16G : M18x1,5 p/n 614 87 10 Puller disk p/n 916 94 72 Disassembly tool kit p/n 916 94 70 Disassembly tool kit p/n 916 94 70 Spindle with puller nut p/n 614 70 70 Puller dome for wheel bearing set p/n 614 70 90 Disassembly tool kit with basic device p/n 916 94 75 Disassembly tool kit p/n 916 94 70 Hydraulic set 5 pcs p/n 802 50 000 Disassembly tool kit with hydraulic p/n 916 94 80
D 13
Passenger car wheel hub puller and drive shaft ejector Flange for pulling hubs with 3, 4 and 5 hole divisions, suitable for nearly all passenger car marques with a pitch from 98.0 mm to 139.7 mm. Flange p/n 614 78 50 Adapter (2 ¼ x16G to 1½ x16G) p/n 614 91 41 Adapter (1½ x16G to M18X1,5) p/n 614 87 10 Hydraulic spindle12 tonne p/n 104 16 50 Spare wheel screws 15 pcs p/n 614 87 290 Spare wheel screws 15 pcs p/n 614 87 390 Case empty with burl foam material p/n 880 08 50 Hard aerated plastic insert punched out p/n 880 00 86 Drive shaft ejector and wheel hub puller p/n 614 79 001 Flange p/n 614 78 50 Adapter (2 ¼x16G to 1½ x16G) p/n 614 91 41 Adapter (1½ x16G to M18X1,5) p/n 614 87 10 Drive shaft ejector and wheel hub puller p/n 614 68 50 Flange p/n 614 78 50 Adapter (2 ¼x16G to 1½ x16G) p/n 614 91 41 Cone rings set 5 pcs. p/n 614 79 70 Drive shaft ejector and wheel hub puller p/n 614 68 505 Extract flange with adapters p/n 614 68 50 Mechanical spindle (M18x1,5x210mm) p/n 614 78 60 Cone rings set 5 pcs. p/n 614 79 70 Drive shaft ejector and wheel hub puller (mechanical) p/n 614 78 00 Extract flange with adapters p/n 614 68 50 Hydraulic spindle 12 tonne p/n 104 16 50 Cone rings set 5 pcs p/n 614 79 70 Case empty with burl foam material p/n 880 08 50 Hard aerated plastic insert punched out p/n 880 00 86 Drive shaft ejector and wheel hub puller (hydraulic) p/n 614 79 00 Accessories Extension for the hydraulic spindle for Audi A4, A6, Ford p/n 990 16 50 Slide hammer 5kg p/n 614 87 90 Slide hammer 8kg p/n 614 88 00 Spacer ring universal without screws p/n 614 86 98 Spare wheel screws 5 pcs M 12x1,25 60 mm long with washers p/n 614 87 330 Spare wheel screws 5 pcs M 12x1,5 60 mm long with washers p/n 614 87 340 Spare wheel screws 5 pcs M 14x1,5 60 mm long with washers p/n 614 87 350 Spacer ring complete with 15 screws and washers p/n 614 86 95 Spacer ring with Spare wheel screws for BMW 5 pcs M 12x1,5, 60 mm long with washers p/n 614 86 90 Spacer ring with Spare wheel screws for Volvo 5 pcs M 14x1,5, 60 mm long with washers p/n 614 86 94
D 14
Hub extractor 4, 5, and 6 hole divisions. For ejecting the drive shaft and when used with the slide hammer extracting the wheel hub. The puller can also be used with the 10t hydraulic cylinder p/n 8025110 directly or with the 12t open core hydraulic cylinder*. (*12t adapter and 12t spindle must be present). Type : universal, e.g. Transporter, off road Vehicles, Ford Transit, MB Sprinter, Nissan Interstar / Primastar, Opel Arena, Movano, Renault Trafic / Master, Toyota Hydraulic spindle 12 tonne p/n 104 16 50 Hub extractor without hydraulic spindle 12 tonne p/n 614 86 79 Hub extractor with hydraulic spindle 12 tonne with 5 cone rings and 2 adapters (incl. M 18 x 1,5) p/n 614 86 80 Accessories: Slide hammer 5kg (thread M 18x1,5) p/n 614 87 90 Slide hammer 8kg (thread M 18x1,5) p/n 614 88 00 12t spindle 3 pcs for hydraulic open core cylinder* p/n 617 60 80 Adapter for hydraulic open core cylinder * p/n 614 91 47 Wheel hub counter support front axle
Counter support for wheel hub ejection.
With the counter support installed on the internal knuckle and used with hub puller p/n 614 86 80 the hub is quickly and safely ejected. Type : Opel Movano, Nissan Interstar, Primastar, Renault Master Wheel hub counter support p/n 614 25 90 To be used with: Hub extractor with hydraulic spindle 12 tonne p/n 614 86 80
Hub bolt extensions for wheel bolts These extensions can be used in connection with extraction flanges p/n 61479001 and p/n 6148680 when expressing the drive shaft or when disassembling wheel hubs. The hub bolts are installed in place of the wheel bolts which are usually too short to allow you to screw the flange on securely. They can also be used as a spacer for protruding wheel hubs. Hub bolt extension passenger car 1 piece for M12x1,25 p/n 614 78 512 Hub bolt extension passenger car 1 piece for M12x1,50 p/n 614 78 513 Hub bolt extension passenger car 1 piece for M14x1,50 p/n 614 78 514 Hub bolt extension passenger car 1 piece for M14x2,00 p/n 614 78 515 Hub bolt extension passenger car 1 piece for M16x1,50 p/n 614 78 516 Shouldered nut M14 for hub bolt extension 1 piece p/n 614 78 519 Hub bolt extension passenger car set complete 25 pcs M12, M14 & M16 for the extractor flanges p/n 614 78 520
D 15
Adapter with spindle for the admission of a hydraulic open core cylinder This adapter is used with ejecting the drive shaft from the hub with a hydraulic open core cylinder. Used in connection with the basic equipment U14 ideally suitable for the replacement of bushes. Hydraulic adapter with spindle p/n 614 91 55
Slide hammer 8 Kg Can be universally used on M18x1,5 threads. The 8 kg slide hammer provides tremendous traction to the parts to be removed. Slide hammer complete 8 kg with spindle thread M18x1,5 p/n 614 88 00
Slide hammer 5kg Slide weight approx. 5 kg. With safety grasp (thumb protection). For application with our wheel hub pullers, drive shaft retraction nuts or body work tools Slide hammer 5 kg (thread M 18x1,5) p/n 614 87 90 Adapter size 2 M 20 x 1,5 to M 18 x1,5 p/n 613 26 10
Hub grinder 1 & 2 Number of revolutions max. 1500 rpm For the cleaning of the wheel centre and the contact surface (wheel /brake disk to the hub). For application in connection with a drill, portable electric drill or pneumatic drill. Replaceable cleaning disks with Velcro fastening. Long service life of the cleaning disk. Small dust formation contrary to wire brushes etc. because of the open-porous abrasive and cup-shaped basic equipment, no flying sparks and a perfect finish. The cleaned contact surface ensures a flat seat for the brake disk and wheel thus maintaining the clearances of the brake disk and getting the genuine torque values. Hub grinder size 1 (Ø 160) mm p/n 614 95 60 Basic device with 3 cleaning disks Cleaning disks 3 pcs size 1 (Ø 160) p/n 614 95 65 Hub grinder size 2 (Ø 200) mm p/n 614 95 70 Basic device with 2 cleaning disks Cleaning disks 3 pcs size 2 (Ø 200) p/n 614 95 75
D 16
Hub grinder size 3 for wheel studs For the cleaning of the wheel centre and the contact surface (wheel /brake disk to the hub). For application in connection with a drill, portable electric drill or pneumatic drill. Replaceable cleaning disks with Velcro fastening. Long service life of the cleaning disk. Small dust formation contrary to wire brushes etc. because of the open-porous abrasive and cup-shaped basic equipment, no flying sparks and a perfect finish. The cleaned contact surface ensures a flat seat for the brake disk and wheel thus maintaining the clearances of the brake disk and getting the genuine torque values. Type: e.g. Ford, Porsche, Japanese vehicles Hub grinder size 3 (Ø 40/50) mm p/n 614 95 80 2 basic devices with 12 cleaning disks Cleaning disks 5 pcs (Ø 40) p/n 614 95 85 Cleaning disks 5 pcs (Ø 50) p/n 614 95 95
Thread cleaning & repair set
Special set for cleaning or re-cutting damaged threads at hubs, wheel studs and wheel nuts. The threads are frequently damaged due to rust, contamination and error when applying the wheels. Thus starting torques are falsified and/or the threads destroyed completely while tightening. Type: M12 x 1.25, M12 x 1.5 & M14 x 1.5 thread Threaded tapM12 x 1.25 / M12 x 1.5 / M14 x 1.5 Hexagon threading die M12 x 1.25 / M12 x 1.5 / M14 x 1.5 Die wrench M4 till M12 - Core hole drill HSS 6.5mm / 7.5mm Screw pitch gauge, metric, super out M12 / M14 Thread cleaning & repair set 12-tlg. p/n 232 20 10
Prism disk model S 170 x 280 x 4 mm dick Opening max. 69 mm, min. 29 mm For applications where there is little place. Special steel, particularly slim version, similarly to a torsion bar. For work on the workshop press, e.g. for transmissions, axles etc. Type : Universal Prism disk model S p/n 615 88 00
D 17
Prism disk model R 250 x 200 mm Sizes: a - 43 mm, 60 mm, 75 mm, 80 mm b - 30 mm, 40 mm, 50 mm, 80 mm For the pressing on or extracting of bearings, pinions etc. For use on the bench press Type: Universal Prism disk model R p/n 615 87 00 Snap ring pliers „NEW“ for wheel hubs PSA Suitable for models up to 2005 and from 2005 The wheel bearing snap ring pliers for Peugeot wheel bearing has been modified, to accommodate models starting from 2005. Our pliers with the p/n 9103300 only fit the models to year of construction 2005, the new pliers fit for all models thus also the model starting from 2005 Snap ring pliers „NEW“ p/n 910 22 00 Spare sickle blade p/n 910 22 05
Wheel bearing thrust piece set Wheel bearing thrust piece set, 3 piece to remove the snap ring without grab holes on PSA vehicles p/n 910 33 10
Wheel bearing thrust piece set, 4 pieces for PSA with pliers p/n 910 33 25
Wheel bearing thrust piece set, 5 pieces for PSA with pliers and a spare sickle blade p/n 910 33 30
Wheel bearing set UNI Universal tool kit to the disassembly/assembly of wheel hubs and wheel bearings without dismounting the shock struts. Applicable directly on the vehicle. Complete with 2 basic devices, 1 spacer, 9 different disks and 1 pressure spindle with distance adapter and bearing.
Wheel bearing set UNI p/n 614 69 30 in a sturdy plastic case
D 18
Wheel bearing and separation tool kit front axle Transporter PSA Boxer, Jumper, Fiat etc. Extruding disk p/n 614 61 15 Support sleeve p/n 614 61 22 Support disk p/n 614 61 23 Press in disk p/n 614 61 27 Support tube p/n 614 61 28 Press in disk p/n 614 61 29 Thrust piece p/n 614 80 79 Press bolt p/n 614 80 88 Prism disk pair p/n 614 88 45 Wheel bearing and separation tool kit front axle for Transporter PSA Boxer, Jumper, Fiat etc. p/n 614 61 20
Wheel bearing disassembly and assembly tool set 8 pcs for Renault master, OPEL Movano, Nissan Interstar Thrust piece size 2 p/n 614 61 11 Thrust piece size 7 p/n 614 61 16 Thrust piece size 9 p/n 614 61 18 Support-/distance sleeve with exchange stud p/n 614 62 80 Thrust piece size 5R p/n 614 80 79 Press in/out bolt p/n 614 80 88 Support bolt p/n 614 80 91 Prism disk pair p/n 614 88 45 Wheel bearing de and assembly tool set p/n 614 61 95
Support sleeve 4 In addition to existing sets p/n 6146195 and 6146120 is this support sleeve no. 4 used for all new models with a hub diameter of 140 mm with 17“ wheels. Type: Peugeot Boxer, Renault Master et al.. Support sleeve 4 p/n 614 61 31
Wheel bearing assembly tool no. A2 front axle Front wheel bearing Type : Audi A3, A4 1,6-1,9 VW Golf IV, Passat from ´97 Skoda Oktavia Basic device with spindle p/n 614 71 00 Distance sleeve A3, Golf IV p/n 614 75 25 Retract disk A3, Golf IV p/n 614 74 85 Retract disk A3, Golf IV p/n 614 74 95 Extract disk A3, Golf IV p/n 614 73 40 * Distance sleeve size 5 A4, Passat p/n 614 72 35 * Centre disk size 1 A4, Passat p/n 614 72 38 * Counter draw disk size 1 A4 , Passat p/n 614 72 40 * Retract disk size 8 A4 , Passat p/n 614 72 42 * Extract disk size 5 A4 , Passat p/n 614 72 45 Wheel bearing assembly tool no. A2 p/n 614 73 90 Wheel bearing assembly tool no. A2 supplement without basic device and spindle p/n 614 73 93
D 19
Wheel bearing assembly tool no. 2 front axle
Front wheel bearing
Type : Audi A4 1,6 – 1,9 VW Passat from `97 Basic device with spindle p/n 614 71 00 Distance sleeve size 5* p/n 614 72 35 Centre disk size 1* p/n 614 72 38 Counter draw disk size 1* p/n 614 72 40 Retract disk size 8* p/n 614 72 42 Extract disk size 5 * p/n 614 72 45 Wheel bearing assembly tool no. 2, p/n 614 72 90 * Wheel bearing assembly tool no. 2a supplement 5 pcs without basic device with spindle p/n 614 72 95
Wheel bearing assembly tool no. 2a + 2b, p/n 614 72 10 without basic device and spindle Wheel bearing assembly tool no. 2 + 2b, p/n 614 72 20 with basic device with spindle
Univ. wheel bearing disassembly and assembly tool Universal wheel bearing disassembly and assembly tool p/n 914 69 30
Press wheel bearing bolt Outside Ø: 28 mm Length without thread: 178 mm Thread: M20 x 1.5 Supplement to wheel bearing tool p/n 914 69 30 In connection with the extracting / press in disks for the disassembly/assembly of the wheel bearings on the dismounted shock strut on the press table Press wheel bearing bolt p/n 614 72 00
D 20
Wheel bearing assembly tool no. 3 front axle Front wheel bearing
Type : VW-Transporter T4
Basic device with spindle p/n 614 71 00 * Distance sleeve size 4 p/n 614 76 80 * Counter draw disk size 2 p/n 614 74 48 * Retract disk size 10 p/n 614 74 45 * Extract disk size 7 p/n 614 73 45 Wheel bearing assembly tool no. 3, 5 pcs in a case p/n 614 73 70 * Wheel bearing assembly tool no.3, supplement 4 pcs without basic device and spindle p/n 614 73 80
Wheel bearing assembly tool no. 3b front axle Front wheel bearing Type : VW Sharan, Ford Galaxy, Seat Alhambra 1,9 Diesel, 2,0 and 2,8 V6 Basic device with spindle p/n 614 71 00 *Distance sleeve p/n 614 65 51 *Extract disk p/n 614 65 52 *Retract disk p/n 614 65 53 *Centre disk p/n 614 65 54 Wheel bearing assembly tool no. 3b, 5 pcs in a case p/n 614 65 50 *Wheel bearing assembly tool no. 3b, supplement 4 pcs. without basic device and spindle p/n 614 65 55
Wheel bearing assembly tool no. 12 front axle Front wheel bearing Type : Ford Escort, Mondeo Basic device with spindle p/n 614 71 00 *Distance sleeve size 7 Escort p/n 614 64 71 *Counter draw disk size 7 Escort p/n 614 64 72 *Retract disk size 25 Escort p/n 614 64 73 *Extract disk size 2 Escort p/n 614 73 20 *Distance sleeve size 18 Mondeo p/n 614 64 81 *Retract disk size 26 Mondeo p/n 614 64 82 *Extract disk size 4 Mondeo p/n 614 73 40 Wheel bearing assembly tool no. 12 8-tlg. in a case p/n 614 64 50 *Wheel bearing assembly tool Nr.12 supplement 7 pcs without basic device and spindle p/n 614 64 45
D 21
Wheel bearing assembly tool no. 15 rear axle Rear wheel bearing Type : Ford Focus Basic device with spindle p/n 614 71 00 *Distance sleeve p/n 614 64 71 *Adapter disk p/n 614 64 72 *Retract disk p/n 614 64 10 *Extract disk p/n 614 64 91 Wheel bearing assembly tool no. 15 complete in a case p/n 614 64 90 *Wheel bearing assembly tool no. 15 supplement without basic device and spindle p/n 614 64 95
Wheel bearing assembly tool no. 8 rear axle Rear wheel bearing Type : MB W 201 -124 -129 - 202 - 210 Basic device with spindle p/n 614 71 00 *Distance sleeve size 11 p/n 614 63 81 *Counter draw disk size 4 p/n 614 63 20 *Retract disk size 18 p/n 614 63 30 *Extract disk size 11 p/n 614 63 40 Wheel bearing assembly tool no. 8 complete 5 pcs in a case p/n 614 63 50 *Wheel bearing assembly tool no. 8 supplement without basic device and spindle p/n 614 63 70 Wheel bearing assembly tool supplement 3 pcs p/n 614 63 88 Type : MB W140
Wheel bearing assembly tool no. 17 front axle Front wheel bearing Type : MB A class bearing no. : SKF=BAH 0059. Basic device with spindle p/n 614 71 00 *Extract disk p/n 614 72 46 *Counter draw disk p/n 614 74 10 *Retract disk p/n 614 74 41 *Distance sleeve p/n 614 75 00 Wheel bearing assembly tool no. 17 complete 5 pcs in a case p/n 614 63 60 *Wheel bearing assembly tool no. 17 supplement 4 pcs without basic device and spindle p/n 614 63 90 For disassembly of the hub: Wheel hub puller p/n 614 77 00
D 22
Wheel bearing assembly tool 11 V front axle Front wheel bearing
Type : Peugeot 106 from `95 - 205 - 309 - 405 - 406
Distance sleeves for pressing out and in, used in combination with the wheel bearing tool or at the press table. Type : Peugeot 205, 309 (Ø 77 mm) p/n 614 75 65 Type : Peugeot 205, 309 (Ø 85 mm) p/n 614 75 75
Wheel bearing assembly tool 5 front axle Front wheel bearing
Type : Renault R 5 - 9 - 11, CLIO and R19 with bearing no. 7701462469 and 7701464049
Basic device with spindle p/n 614 71 00 *Distance sleeve size 9 Renault, almost all passenger cars p/n 614 62 55 *Counter draw disk size 3 p/n 614 62 10 *Retract disk size 15 p/n 614 62 30 *Retract disk size 16 p/n 614 62 40 *Extract disk size 8 p/n 614 62 20 Wheel bearing assembly tool no. 5, 6 pcs in a case p/n 614 62 00 *Wheel bearing assembly tool no. 5 supplement without basic device with spindle p/n 614 62 05 Wheel bearing assembly tool no. 5b supplement Type : Renault Laguna, Clio, R 19 Distance sleeve p/n 614 62 60 Retract / Extract disk Ø 82 mm p/n 614 61 70 Retract / Extract disk Ø 72 mm p/n 614 61 75 Wheel bearing assembly tool no. 5b supplement 3 pcs p/n 614 61 80
Distance sleeve model ABS For the disassembly/assembly of the wheel bearings together with the wheel bearing tools. Alternatively the distance sleeve can be used on the press. Type : Renault with ABS et al. (not for the Laguna from `98) Distance sleeve model ABS p/n 614 62 65
D 23
Distance sleeve model UNI Adjustable distance sleeve with three pairs of top parts used in addition to the wheel bearing tools or for use on the bench press. At the base plate of the distance sleeve the diameter can be adjusted according to the wheel bearing housing. The different top parts are selected depending on the shape of the wheel bearing housing and installed on the distance sleeve. Additionally the top parts can be shifted separately on the guide. Thus the distance sleeve is optimally adjustable to the wheel bearing housing shape. Type : universal Distance sleeve model UNI p/n 615 87 60 in a case
Top parts supplement „TRANSPORTER“ For adjustable distance sleeve The supplement consists of 3 strengthened guides for the 95.0 mm top parts narrow and broad, of which there are 1 pair each in the set. Supplement 7 pcs; 2 pair top parts size 4 and 5 length 95,0mm with 3 strengthened guidance’s p/n 615 87 650 Strengthened guidance 1 piece for top part “long” p/n 615 87 655 Top parts pair broad size 4 long version 95,0 mm p/n 615 87 615 Top parts pair narrow size 5 long version 95,0 mm p/n 615 87 625
Distance sleeve model SUV Basic device with strengthened top parts Distance sleeve model SUV p/n 615 87 70
Assembly paste anti seize 10 g High performance grease for strongly loaded spindles, e.g. on wheel bearing and bush tools. Temperature-resistant protects against corrosion, seizing and wear. The handy one-way syringe makes a proportioned and clean application possible. Assembly paste anti seize p/n 816 01 00
D 24
Bearing inner race drawer Precise clamping devices for removal of the inner race wheel bearing remaining on the hub during wheel bearing change. An operational compilation consists of: basic device + spindle + clamping device + thrust piece (with hollow shafts) Sample applications for the clamping devices: Size 1 Alfa, Audi, Ford, Peugeot, Lancia, Renault, VW Size 2 Alfa, Audi, Ford, Renault Size 3 Citroen, Ford, Opel Vectra B, Renault, VW Golf IV Size 4 BMW, Renault, Peugeot Size 5 Citroën XM, Xantia Size 6 BMW E 39, Safrane, Laguna, Megane, Size 7 Alfa, Fiat Tipo, UNO, Panda, Lancia, VW Polo Size 8 Opel Kadett, Corsa, Astra, Citroen, AX/ZX Size 9 Lancia, Opel Vectra A front axle, Peugeot Size 10L* BMW E32/38, Opel Omega A/B rear axle Long version Basic device size 1 standard p/n 614 80 83 Basic device size 2* p/n 617 81 41 Spindle M16 x 1,5 x 100 standard p/n 614 80 86 Spindle M16 x 1,5 x 150 p/n 614 80 89 Clamping device Ø -reach basic device Size 1 46-50 size 1 p/n 614 80 71 Size 2 48-52 size 1 p/n 614 80 72 Size 3 54-58 size 1 p/n 614 80 73 Size 4 56-60 size 1 p/n 614 80 74 Size 5* 58-62 size 2 p/n 614 81 44 Size 6* 62-66 size 2 p/n 614 81 45 Size 7 40-44 size 1 p/n 614 80 69 Size 8 45-49 size 1 p/n 614 80 81 Size 9 50-54 size 1 p/n 614 80 82 Size 10L 51-54 size 1 p/n 614 80 41 Thrust piece Ø height Size 1 30 / 21 15 mm p/n 614 80 76 Size 2 38 / 21 25 mm p/n 614 80 77 Size 3 38 / 21 16 mm p/n 614 80 78 Size 4a 28 / 21 15 mm p/n 614 80 85
D 25
Bearing inner race puller This set is suitable for 90% wheel bearings available on the market. With this particularly affective puller the wheel bearing inner race, which remains on the hub during the wheel bearing change, is pulled simply and efficiently.
This universal puller has a clamping range from 40,0 to 60.0 mm and is suitable for work, where sufficient place is present for the attachment of the puller.
Triple arm bearing inner race puller Clamping range 40-60 mm p/n 614 80 525
D 28
Bearing race drive out To remove seized bushes ( on commercial vehicles, also rough fork sockets), e.g. for the bushes of the split taper roller bearings in the wheel hubs. Possible to regrind! Type : universal Bearing race drive out passenger cars p/n 616 94 00 300 mm lg. Bearing race drive out commercial vehicles p/n 616 94 95 510 mm long x 24mm hexagon
Bearing race assembler commercial vehicles Area of application of 92 mm - 165 mm Ø For tilt-free and central mounting of bushes. Adjust the cheeks to the inside diameter clamp the bush and punch it in.
Wheel bearing outer race/grease cap driving tool model A For the damage-free and central driving of outer bearing races and the dust/grease caps on the rear axle. Formation of chips when driving is prevented, so that no damage to the wheel bearings is caused.
Type : Audi / VW (not all wheel drive)
Driving bolt 150 mm lg., M 16 x 1,5 p/n 616 94 51 Driving disk Ø 40 mm p/n 616 94 52 Driving disk Ø 45 mm p/n 616 94 53 Driving disk Ø 50 mm p/n 616 94 54 Driving sleeve dust caps Ø 40 / 45 mm p/n 616 94 35 Wheel bearing outer race/grease cap driving tool model A 5 pcs p/n 616 94 60 in a plastic case
Pressure piece set ALU Versatile pressure piece set made from aluminium. The installation forces are transferred evenly and carefully so that damage to ball bearings, sockets, shaft seals etc are avoided. For use with a rubber or plastic hammer Contents: 1 handle 120 mm long with retaining screw 9 pressure pieces with outside Ø: 40/ 44/ 50/ 59/ 63/ 65/ 72/ 76/ 81 Pressure piece set ALU 10 pcs p/n 614 45 30
D 29
Pressure piece set 15 pcs Pressure piece set universal 60 – 85mm, 15 pcs with 3 washers 50 – 130mm Pressure piece set 15 pcs p/n 614 61 30 in a case
Pressure piece set 11 pcs Pressure piece set universal 60 – 85mm, 11 pcs without washers Pressure piece set 11 pcs p/n 614 61 40 in a case
Grease cap driving in tool model F For the damage-free and central driving of the dust/grease caps on the rear axle. Formation of chips is prevented when driving so that no damage to the wheel bearings is caused.
Type : Ford Escort, Mondeo, Transit front axle
Drive in bolt 150 mm lg., M 16 x 1,5 p/n 616 94 51 Drive in sleeve for dust/grease caps p/n 616 94 16 Grease cap driving in tool model F 2 pcs . p/n 616 94 15
Grease cap driving in tool model MB For the damage-free and central driving of the dust/grease caps at the front axle wheel bearings Formation of chips is prevented when driving so that no damage to the wheel bearings is caused. .
Type : MB all passenger cars
Drive in bolt 150 mm lg., M 16 x 1,5 p/n 616 94 51 Drive in sleeve Ø 52 / 60mm p/n 616 94 34 Grease cap driving in tool model MB 2 pcs . p/n 616 94 40
Socket E22 impact commercial vehicle E-profile E 22 x 100 mm x 3/4" drive For the disassembly and assembly of cylinder head screws. Type: commercial vehicles, e.g. MAN new TGA engines Socket E22 impact p/n 606 28 22
Axle nut socket Universal socket from 55,0 to 150,0mm Type : commercial vehicles e.g. screwed in grease caps. Screwed in drive shafts etc. Axle nut socket p/n 915 87 60
D 30
Manual thread cutter commercial vehicles For re-cutting and equalizing damaged threads on the axle stub of commercial vehicles etc.,. Step less adjustment from 25 to 140 mm Ø. Included are a set of metric and imperial re-threaders Pitch metric : 1,0-1,25-1,5-1,75, 2,0-2,5-3,0-3,5, 4,0 Manual thread cutter commercial vehicles p/n 276 00 00 Replacements sets : Re-threading set 3 pcs metric p/n 276 00 60
Swing arm clamping screw push out tool For pushing out the upper wishbone clamping screw on Audi A4, A6,VW Passat vehicles from 1997 which have the four swinging arm wheel axle. Swinging arm clamping screw pusher tool p/n 917 46 30
Swinging arm screw drill-out tool Supplement for accurately drilling the four swinging arm clamping screw. Using the 2 screwed on drilling cases first for predrilling the screw will then be drilled out to the thrust bolt measure. The clamping screw is then drilled out into the casting body. Using the thrust bolt to press centraly on the screw core. The thread is not distorted, which can often prevented the removal from the casting body. Also suitable for removal tools from other manufacturers Release nut 1/2" With this and an impact screwdriver the clamping screw is first “shaken loose". The release nut is then screwed onto the protruding end of the clamping screw
Type : Audi A4, A6, VW Passat 97, vehicles with four swinging arm wheel axle.
Swinging arm clamping screw drill-out tool p/n 613 40 00 Release nut 1/2" p/n 113 51 00 Swinging arm clamping screw drill-out -/ push out tool in a plastic case p/n 617 46 80
D 31
Hydraulic hand pump model 11 (single acting) Usable tank volume: 655 cm3 Piston displacements: 2.62 cm3 Weight: 5.9 kg Max. lever strength: 50 kg max. Operating pressure: 700bar Overall length: 585 mm , Connection: 3/8" - 18 NPT Economical single-step hand pump with a large tank capacity for single acting cylinders, with a manually operated reverse valve for forward and return. Built in relief valve for overload protection. Recommended for cylinders from 10t Hydraulic hand pump model 11 (single-acting) p/n 802 55 10
Hydraulic hand pump model 22 (double acting) Usable tank volume: 901 cm3 Piston displacement stage I/II: 11,26/2.47 cm3 Weight: 4.1 kg Max. lever strength: 42.2 kg max. Operating pressure: 700bar Overall length: 549 mm Connection: 3/8" - 18 NPT 1. Small weight and compact build 2. Nylon tank and nylon-coated aluminium housing for highest corrosion protection 3. Through double action 78% fewer pump strokes. Recommended if the cylinder must drive out quickly in order to make contact and fix the thrust pieces. 4. Large tank capacity for versatile employment 5. Build in relief valve as overload protection Recommended for cylinders 10t - 20t Hydraulic hand pump model 22 (double acting) p/n 802 55 20
Air hydraulic foot pump 10000 P.S.I. / 700 BAR High performance air powered hydraulic foot pump, an addition to the wheel bearing tool kits, time-saving operation one man operation Air hydraulic foot pump HL-2810 p/n 802 55 65
D 32
Hydraulic high-pressure hose Length 2.20 m Bursting pressure 1.400 bar Max. permissible operating pressure 700bar Connection 3/8" NPT. Suitably for all Pichler hydraulic tools. For high demand with high resistant external layer and spring break protection for increased stability against wear Hose adapter with ball valve for the oil loss-free change of individual components without additional tools. Hydraulic high-pressure hose 2,20 m long p/n 802 53 00 Hose adapter with ball valve p/n 802 54 00
Hydraulic cylinder 10 t Maximum force: 10 t Stroke: 156 mm Height retracted: 247 mm Cylinder outside Ø: 57 mm Oil volume: 226 cm ³ Operating pressure: 700 bar Weight: 4.4 kg
Cylinder made from high-strength alloyed steel with spring return and substantial bronze guides. Developed for use in all situations. The piston rod for protection against corrosion and wear is chromium plated. With Pichler standard quick-coupler. Employment: e.g. ball joint and silent bush tools. Hydraulic cylinder 10 t p/n 802 51 10
Hydraulic hollow piston cylinder 12 t Maximum force: 12 t Stroke: 42 mm Overall height retracted: 120 mm Cylinder outside Ø: 69 mm Oil volume: 75 cm ³ Operating pressure: 700 bar Weight: 2.8 kg Hole: 20,2 mm External thread: 2 3/4" – 16
End to end hollow piston for the use with pressure spindles, hauling cables etc. The hollow piston construction makes possible the employment of the cylinder for pushing and pulling work. With strong spring release and Pichler standard quick-coupler.
Employment: e.g. wheel bearings, hubs, silent bearing etc.
Hydraulic hollow piston cylinder 12 t p/n 802 51 00
D 33
Hydraulic hollow piston cylinder 20 t Maximum force: 20 t Stroke: 76 mm Overall height retracted: 200 mm Cylinder outside Ø : 98 mm Oil volume: 150 cm³ Operating pressure : 700 bar Weight : 8,6 kg Hole : 26,9 mm. The hollow piston construction makes it possible to use the cylinder for pushing and pulling work. With strong spring release and Pichler standard quick-coupler. Stationary employment of two tapped holes in the base and an additional adapter ring are possible Employment: e.g. for all wheel knuckle tool set p/n 614 27 50 and silent bushes on commercial vehicles. Hydraulic hollow piston cylinder p/n 802 51 40 Adapter rings attachment on the cylinder with allen screws Size 2 tool connecting thread M 65 x 2 p/n 614 27 90 Size 3 tool connecting thread M 60 x 1,5 p/n 614 28 00
Hydraulic flat cylinder Model/ Maximum force: 10t 20t Stroke: 12 mm 11 mm Height retracted: 42 mm 51 mm Cylinder external dimensions: 82 x 55 mm 101 x 76 mm Operating pressure: 700 bar 700 bar Weight : 1,4 kg 3,1 kg
Compact, flat version for employment where other cylinders are too large. Mounting holes make simple assembly possible. The grooved piston end makes thrust pieces redundant. With Pichler standard quick-coupler.
Employment: e.g. trace and connecting rod head pullers for commercial vehicles Hydraulic flat cylinder 10t p/n 802 51 60 Hydraulic flat cylinder 20 t p/n 802 51 50
D 34
Hydraulic set 12t For use with different bush and ball joint tools model R also for the wheel bearing tool. Optimal working is ensured by the maximum traction power of 12 t. Replacement of bushes and ball joints is made much easier by the use of hydraulics. Hand pump model 11 Usable tank volume. 655 cm3 Hydraulic high-pressure hose 2,20 m long. Hose adapter with ball valve For the oil loss-free change of hydraulic cylinder. Hydraulic hollow piston cylinder 12 t Stroke: 42 mm Hole : 20,2 mm Wheel bearing spindle 450 mm long, With extraction nut (p/n 6147141) for use with of the hydraulic insert. 1) Hand pump model 11 p/n 802 55 10 2) Hydraulic high-pressure hose 2,20 m long. p/n 802 53 00 3) Hose adapter with ball valve p/n 802 54 00 4) Hydraulic hollow piston cylinder 12 t p/n 802 51 00 5) Wheel bearing spindle 450 mm (only model R) p/n 614 71 40 Hydraulic set model B 3 pcs. 1, 2, 3 p/n 802 55 50 Hydraulic set model S 4 pcs. 1, 2, 3, 4 p/n 802 49 00 Hydraulic set model R 5 pcs. 1, 2, 3, 4, 5 p/n 802 50 00
XZN special sockets Impact sockets with ½ “ drive in short 40.0 mm and long 75.0 mm versions XZN M14, XZN M16 and XZN M18. These are required for the release and tightening of the special screw connections in the chassis and suspension. Manufactured in one part, thus extremely though. XZN special sockets ½“ drive 6 pcs XZN 14,16,18 impact 40,0 mm and 75,0 mm long p/n 794 05 00
E 01
Vacuum extraction pump Pneumatic and manual operation. Includes 3 extraction hoses, container volume is 6.5 litres Can be used for siphoning off most fluids for example, fuels, oils, water, brake fluid and coolants. This pump can be operated both pneumatically or by using the hand pump to produce negative pressure in the 6,5 litres container. With manual use one is independent of power sources or compressed air and thus has substantially more flexibility. The equipment is provided with 3 different suction hoses, which have outside diameters of 5,0 - 7.0 and 10.0 mm. The length of each is approx. 1 meter. Vacuum siphon pump pneumatic and with manual control 6,5 litre with 3 extraction hoses p/n 901 18 00
Pump for extraction and filling Manual operation. With a change over valve for extraction or filling - container volume is 8.8 litres This version be used for extracting most different fluids for example, fuels, oil, water, brake fluid and coolants. By operating the change over valve the mode can be changed from extraction to filling. As operation by hand pump produces negative and/or positive pressure in the 8,8 litres container and is independent from electrical or compressed air sources the unit offers great flexibility of use. This device is equipped with 1 hose and 2 probes for the
extracting of engine oil. Hand extracting pump for extracting and filling of liquids, 8,8 litre with 1 hose and 2 probes p/n 901 19 00
Double action pumps extraction and pressure Volumes 125ml and 250ml Robust hand extraction pumps with double stroke. The pumps pump fluid with each movement; therefore there are no “no-load operation “pump strokes. The aluminium housing and plastic parts from which the pumps are manufactured, are suitable for liquids such as diesels, heating oil, engine oil, brake fluid, water and different coolants. ATTENTION these pumps are not to be used for petrol, acids and caustic solutions! Double-acting pump universal 125 ml volume aluminium housing with plastic hoses p/n 80125125 Double-acting pump universal 250 ml volume aluminium housing with plastic hoses p/n 80125250
E 02
Brake service adapter Manufacturer / Type My. Adapt. P/n Manufacturer / Type My. Adapt. P/n
ALFA-ROMEO Vision 61A 8064610
All passenger cars 20 8064200 Viper 03- 22 8064223
Giulietta 81-86 27 8064270 Voyager LE 96 - 22 8064223
Brake fluid tester model 1 Brake fluid: DOT 4 Measurement: % water content Measures: 100 x 60 x 30 mm Display: LED Probe: 52 mm long. Electronic brake fluid tester with keypad for the fast examination of the water content of brake fluid. Brake fluid tester model 1 p/n 422 40 00
Brake fluid tester model EBT 03 Electronic brake fluid tester for different kinds of brake fluid such as DOT 3, DOT 4, DOT 4 plus and DOT 5.1. The device is menu led and shows the measurement results in the form of the boiling temperature (in °C) and the water content (in %). Supplied in a cardboard box.
Characteristics:
• processor-controlled
• with two-line, alphanumeric display
• automatic measuring start when immersing the sensor
• Low battery notification
• automatic shut off of the equipment after 2 minutes without measurement
• Voltage supply over 9 V battery. Brake fluid tester model EBT 03 p/n 422 35 00
Brake flaring tool model M For pipes 4,75 mm of copper, steel or aluminium with up to 1,0 mm wall thickness. For SAE and DIN single and double flange.
Handy mechanical flaring tool that can be used on the vehicle. This compact tool can be used in restricted work areas, e.g. at the rear axle. The few individual parts can be installed simply, thus the flaring tool is fast and ready to use. The full set contains a deburring device, a pipe cutter and bending device.
Brake flaring tool model M complete p/n 613 32 14 Brake flaring tool model p/n 613 32 13 without deburring device, a pipe cutter and bending device
E 10
Brake bleeder spanner 11 mm
For the manipulation of the hard to reach bleeder screws at the rear axle without the need for disassembly/assembly of the rear wheels. The silicone hose is placed over the breather nipple before setting the spanners. Thus an absolutely leak free operation is ensured.
Model 1 29 mm height p/n 613 44 55 Type: Passat, Audi A4, etc.
Model 2 75 mm height p/n 613 44 65 Type: Golf V, Audi A3, Seat Altea, Skoda Octavia new
Brake calliper bleeder valve boring set model uni For drilling out torn off bleeder valves. The valve is drilled out completely with thread and replaced by a threaded bush with new bleeder valve. Type: Universal e.g. Audi, VW, Opel brake calliper Core drill, cylindrical p/n 935 30 11 Tap HSSG NPT ¼"x 18 p/n 935 30 14 Tap HSSG NPT 1/8"x 27 p/n 935 30 18 HSS counter sink 3 flutes 90° p/n 935 30 20 HSS-Co drill 6,0 mm p/n 935 30 16 Special drill 2 pcs 8,5mm p/n 935 30 13 Tread sealant p/n 935 30 08 Bleeder valves 2 pcs (1/4" und 1/8" NPT) p/n 935 30 05 Brake calliper bleeder valve boring set model uni, 12 pcs. p/n 935 30 10 Bleeder valves: 5 x NPT 1/4" (big) p/n 935 30 06 5 x NPT 1/8" (small) p/n 935 30 07
Brake calliper wire brush model K 1 Total length 225 mm, Setting height 22 mm, steal wire, smooth 0,35 mm Ø With a narrow setting. For cleaning the brake callipers and/or brake lines. Brake calliper wire brush model K1 p/n 613 96 00
Brake calliper file model narrow Brake calliper file complete with grip, narrow version for Japanese vehicles. Brake calliper file model narrow p/n 613 85 05
E 11
Calliper wind back tool 3/8" � drive, in a case Special tool kit for winding back brake pads at disc brakes on most available passenger cars. Contents: 2 basic devices (size 1 and size 3L with anti clockwise thread e.g. Ford Mondeo, Fiat), basic device body 2 Ø 38 (to be used with the spindle of basic device size 1) and 15 different inserts. Type : Universal Calliper wind back tool, 20 pcs. p/n 613 87 25 Calliper wind back tool N/O/R Type : Nissan Primastar / Interstar, Opel Vivaro / Movano Renault Kangoo 4wd, new Traffic / Master Calliper wind back tool N/O/R, 5 pcs p/n 613 87 75 Calliper wind back tool Audi/VW 7 pcs p/n 613 87 55 Calliper wind back tool Opel 8 pcs (except Opel Vivaro/Movano) p/n 613 87 72 Opel Vivaro/Movano supplement 3 pcs to p/n 613 87 72 p/n 613 87 76 Calliper wind back tool Ford 10 pcs p/n 613 87 80 Calliper wind back tool Ford 11 pcs p/n 613 87 85 Calliper wind back tool universal 9 pcs p/n 613 88 00
Calliper wind back tool Mechanical wind back tool for different brake calliper versions in the front and rear brakes. Calliper wind back tool p/n 913 87 25
Calliper wind back tool model 4 For Brembo brake systems Type : Renault Calliper wind back tool model 4 p/n 613 97 00 Calliper wind back tool model 5 For pressing back the brake pistons of Girling brake callipers’ with integrated emergency brake (automatic adjustment). Turning and pressing back in one step, includes a counter plate. Type : Renault Espace, Safrane, R19 Calliper pressing back tool model 5 p/n 613 97 50
E 12
Brake disk raised Torx sockets set 3/8“drive Raised Torx sockets in the sizes T-40, T-45, T50 Type : Ford und GM Brake disk raised Torx sockets set p/n 913 48 00
Brake disk extractor model F For extracting front brake disks. Using the 12t hydraulic cylinder extremely seized brake disks can be dismantled safely and quickly. Type : Ford Mondeo `96-00 (except V6) Brake disk extractor model F p/n 613 96 65 without hydraulics Thrust piece for 12t. hydr. spindle p/n 613 96 66 12t hydraulic spindle p/n 104 16 500 Brake disk extractor model F complete p/n 613 96 60 incl. hydraulic spindle
Brake disk and drum extractor Span width ca. 520 mm, span depth ca. 115 mm, Thread 2 ¼" x 16
For extracting the front brake disks of the Mondeo and the rear brake drums of the Transit. Two solid arms with broad puller hooks give the puller a safe hold and distribute the pressure evenly on the brake disk/drum. Using a hand pump and 12t hollow piston cylinders the extremely seized brake disks can be dismantled safely and quickly. The hydraulic components are also used in conjunction with our wheel bearing and certain bush tools. The puller can also be used with the 10t hydraulic cylinder p/n 802 51 10
Type: Brake disks front Ford Mondeo `96-00 Brake drums rear Ford Transit from `00 Brake disk and drum extractor p/n 613 37 61 Adapter for 12t. hydr. cylinder p/n 614 91 90 Adapter size 1 1 1/2" x 16. p/n 614 91 41 12t hydr. open core cylinder stroke 42 mm p/n 802 51 00 Hydraulic hose ca. 2,20 m p/n 802 53 00 Hose adapter with ball valve p/n 802 54 00 Hand pump model 11 p/n 802 55 10 Brake disk and drum extractor with 12t hydr. components p/n 613 37 55
E 13
Brake calliper guidance thread repair set M9 x 1,25 For repairing the guide pin threads in the wheel bearing housing. With disassembly of the guide pins while changing the brake pads the internal threads are frequently destroyed. The defective threads are repaired professionally and quickly with a heavy duty rustproof high-grade steel threaded bush.
Type: VAG, Opel, Ford Drill jig UNI complete with 3 inserts p/n 913 44 11 Drill jig insert size 2 VAG p/n 913 44 12 Drill jig insert size 3 OPEL p/n 913 44 13 Drill jig insert size 4 FORD p/n 913 44 14 Replacement bushes with copper ring M 9x1.25 (packing unit 10 pcs) p/n 613 44 10 Special core drill p/n 613 44 08 Special tap M9x1.25 p/n 613 44 09 Tread repair kit M9x1,25 brake calliper guidance bolds complete with UNI drill jig p/n 913 44 20
Alternative: Repair kit with a rigid rather than universal drilling jig Brake calliper guidance thread repair set model V for VAG p/n 613 44 15
Brake calliper guidance thread repair set model O for Opel p/n 613 44 20
Brake calliper guidance thread repair set model F for Ford p/n 613 44 30
Brake spring tool With clamping screw For easy hooking up of the brake springs. Brake spring tool p/n 913 32 80 Reamer for ABS sensor model 4 Kopf-Ø 10 mm To drill out the defective abs sensor and for reaming and cleaning the locating hole in the wheel bearing housing. The tool permits a damage-free drilling out of the old sensor and provides a clean and correct seat for the new sensor. Because of the integrated fine-interlocked ratchet a clockwise rotation only is possible. Type: VW Golf V, Polo new , T5, Skoda Fabia, Seat Ibiza Reamer for ABS sensor model 4 p/n 613 10 400
E 14
Reamer for abs sensor Length: 180 mm To clean the locating hole of the abs sensor in the wheel bearing housing of rust. Damage to the new sensor during assembly is avoided. Because of the integrated fine-interlocked ratchet a clockwise rotation only is possible. Model 1 Head Ø : 18 mm, head height : 28 mm Type : e.g. Audi/VW, BMW E36/46, Seat, Skoda Model 2 Head Ø : 18 mm, head height: 34 mm Type : e.g. Audi/VW, Seat, Skoda, commercial vehicles Model 3 Head Ø : 15 mm, head height: 28 mm Type : e.g. MB A class, Mazda, Ford Reamer for abs sensor model 1 p/n 613 10 00 Reamer for abs sensor model 2 p/n 613 10 50 Reamer for abs sensor model 3 p/n 613 10 60 Brake disk slide gauge size 1 size 2 Measuring range: 0 - 60 mm 0 - 90 mm Bill length: 85 mm 120 mm Reading: 1/10 mm 1/10 mm To determine wear on brake disks. With divided measuring carriage. Thereby once the thickness of the brake disk is measured, the calliper gauge can be taken of the brake disk, otherwise the measure would be adjusted. Brake disk slide gauge size 1 p/n 402 20 00 Brake disk slide gauge size 2 p/n 402 20 05
Rim puller for commercial vehicles Overall length: 1740 mm Draw hook width: 33 mm Supporting surface: 145 x 40 mm Strong version with double-walled steel tube for the loosening of caked-on wheels. The long assembly lever ensures superior torque. With a tilting assembly head this tool is also suitable for dual tires. Rim puller p/n 105 95 50
E 15
Torque staff These torque staffs make it possible to have controlled tightening of the wheel bolts (+ 7%). By using an automatic tightening stop they can prevent damage to threads and rims.
Warning: Do not use the torque staffs by hand or for releasing wheel nuts. Follow the torque values of the motor vehicle manufacturers. A final check with the torque wrench must take place.
Hand tire filler Calibrated version * Makes examining of the tire pressure and filling the tire possible. * For connection to the workshop compressed air network. * With gas station or lever plugs. * Handy grasp with 2-step fill lever gives optimal handling. (Release and fill position) * Manometer 0 - 10 bar, Ø 80 mm with rubber protective cap. * Manometer with double volume scale bar/psi Complete calibrated devices with official calibration stamp and sequential unit number. Hand tire filler with lever connector p/n 613 94 20 Manometer Ø 80 mm, calibrated Hand tire filler with gas station connector p/n 613 94 40 Manometer Ø 80 mm, calibrated
Wheel security release tool Set of 8 impact sockets sizes 16.8 - 25,8mm ideally to open most of the commonly found security wheel nuts. The sockets are driven using the impact thorn by a hammer onto the security wheel nut and are then removed using a wheel cross. The slim form permits use on rims with very narrow mounting holes. Wheel security release tool p/n 913 77 00
E 16
Wheel security breaker 21 -27,5 mm, 1/2" □ drive
Ideally to open of most normal wheel security nuts Socket size 1+2 - 21x24,5* p/n 913 75 05 Socket size 3+4 – 26x27,5* p/n 913 75 10 Impact extension 75 mm p/n 913 75 15 Wheel security breaker set 2 pcs* p/n 913 75 00 Wheel security breaker set 3 pcs p/n 913 75 50
Twist-Sockets 17 -22 mm, 1/2" □ drive
Sockets made from high-strength special steel with a unique fixing special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded off hexagonal profiles. Twist-Sockets p/n 913 00 30
Twist-Sockets Gr. 2 19 -25 mm, 1/2" □ drive
Sockets made from high-strength special steel with a unique fixing special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded off hexagonal profiles. Twist-Sockets Gr. 2 p/n 913 00 20
Universal hose clamp pliers Locking for exhaust connecting clips On newer vehicles the connection between exhaust pipe and exhaust manifold is made with a hose clamp which can be difficult to remove. This hose clamp is extremely rigid and cannot be spread with conventional pliers without damage or deformation! Universal hose clamp pliers with locking for exhaust connecting clips p/n 605 03 05
Cooling system tester model G Metering range: 0 - 2,5 bar, with quick-coupler. Universally applicable device for the examination of the cooling system. - Radiator evacuating pump Mod. K-SK p/n 404 14 60, made from impact resistant plastic with quick-coupler. - rapid pressure build-up in the cooling system through a long pump stroke. - Impact-protected, well readable manometer. - Release valve - 2 one-turn cap adapters made from steel - 9 system thread adapters The system adapter is connected when needed to the adapter with flexible hose and quick-coupler. Cooling system adapter No.: 1, 18, 23, 26, 31, 32, 38, 42, 62, 65, 81 Type : Universal (see cooling system adapter list) Cooling system tester model G 12-tlg. p/n 405 62 00 in a plastic case
Cooling system tester model 1 Metering range: 0 - 2,5 bar, with quick-coupler. For testing the cooling system as well as the cylinder head leak tightness. Type : Adapter KS 1 57 + 60mm Standard (bayonet cap) Adapter KS 31 Ford KA / Mondeo, Opel, Seat, Skoda, Rover Adapter KS 62.1 Audi, VW , Seat Alhambra, Ford Galaxy Radiator pressure pump model S-SK 2 0 - 2,5 bar p/n 404 15 00 cylinder head leak tightness tester p/n 405 25 00 Test liquid p/n 405 00 10 Adapter KS 1 p/n 404 60 10 Adapter KS 31 p/n 404 63 10 Adapter KS 62.1 p/n 404 66 21 Flexible connector FZ 30 p/n 404 63 00 Cooling water thermometer, dipping shank 135 mm lg. p/n 404 24 00 Cooling system tester model 1 p/n 405 65 00 in a plastic case
Cooling system tester model 2 -NFZ Metering range: 0 - 4,0 bar, with quick-coupler. For testing the cooling system of commercial motor vehicles. With metal adapters. Type : MB, MAN, Iveco Radiator pressure pump model S-SK 1 0 - 4,0 bar p/n 404 14 50 Flexible connector FZ 30 p/n 404 63 00 Cooling water thermometer, dipping shank 135 mm lg. p/n 404 24 00 Adapter cap KS 1 Universal p/n 404 60 10 Adapter cap KS 5 MAN/Krupp p/n 404 60 50 Adapter cap KS 19 MB NFZ, 2-Kreis-Kühlsystem p/n 404 61 90 Adapter cap KS 40 MB-SK, Iveco p/n 404 64 00 Cooling system tester model. 2 p/n 404 71 50 in a plastic case
F 02
Cooling system tester model VAG Radiator pressure pump model S-SK 1 0 - 4,0 bar p/n 404 14 50 Flexible connector FZ 30 p/n 404 63 00 UNI cooling system adapter VA50 p/n 403 36 00 UNI cooling system adapter UA60J p/n 404 66 00 Cooling system adapter AK1 p/n 404 60 10 Cooling system adapter KS38 p/n 404 63 80 Cooling system adapter KS65 p/n 404 66 50 Cooling system tester model VAG p/n 905 69 50 in a plastic case
Cooling system tester model Opel Radiator pressure pump model S-SK 1 0 - 4,0 bar p/n 404 14 50 Flexible connector FZ 30 p/n 404 63 00 UNI cooling system adapter VA50 p/n 403 36 00 UNI cooling system adapter UA60J p/n 404 66 00 Cooling system adapter AK1 p/n 404 60 10 Cooling system adapter KS31 p/n 404 63 10 Cooling system adapter KS77 p/n 404 67 70 Cooling system tester model OPEL p/n 905 69 60 in a plastic case
Cooling system tester model PSA-, Fiat-, Renault Radiator pressure pump model S-SK 1 0 - 4,0 bar p/n 404 14 50 Flexible connector FZ 30 p/n 404 63 00 UNI cooling system adapter VA50 p/n 403 36 00 UNI cooling system adapter UA60J p/n 404 66 00 Cooling system adapter AK1 p/n 404 60 10 Cooling system adapter KS23 p/n 404 62 30 Cooling system adapter KS25 p/n 404 62 50 Cooling system tester model PSA-, Fiat-, Renault in a plastic case p/n 905 69 70
Cooling system tester model Asians Radiator pressure pump model S-SK 1 0 - 4,0 bar p/n 404 14 50 Flexible connector FZ 30 p/n 404 63 00 UNI cooling system adapter VA50 p/n 403 36 00 UNI cooling system adapter UA60J p/n 404 66 00 Cooling system adapter AK1 p/n 404 60 10 Cooling system adapter K33 p/n 404 61 80 Cooling system adapter K47 p/n 404 64 70 Cooling system adapter K56 p/n 404 65 60 Cooling system tester model Asians p/n 905 69 80 in a plastic case
Radiator pressure pump model S-SK 2 Metering range: 0 - 2,5 bar, with quick-coupler. Because of the long stroke of the pump a quick pressure build-up is ensured in the cooling system. The easily readable manometer, Ø 50 mm, is impact-protected by a rubber cap. Radiator pressure pump model S-SK 2 p/n 404 15 00
F 03
Radiator pressure pump model S-SK 1 Metering range: 0 - 4,0 bar, with quick-coupler For compression testing the cooling system up to 4.0 bar. Because of the long stroke of the pump a quick pressure build-up in the cooling system is ensured. The well readable manometer, Ø 50 mm, is impact-protected by a rubber cap. Type : Universal, special BMW M 62 / 73 engine 8 /12 cyl., commercial vehicles Radiator pressure pump model S -SK 1 p/n 404 14 50
Radiator pressure pump Metering range 0-2,5 bar For filler necks with external diameter of 57 mm and 60 mm. For compression testing the cooling system. Radiator pressure pump model SV p/n 404 14 00 clamp buckle, air release valve Radiator pressure pump model SDV p/n 404 13 00 bayonet catch, air release valve Cooling system vacuum filling equipment For bubble free filling of the cooling system. The vacuum filling equipment is connected to the vehicle cooling system with the corresponding cooling system adapter. The vacuum produced allows a leak test of the system to be performed. The system can then be filled bubble free. Simple application without subsequent ventilation saves additional time. Type : Universal Cooling system vacuum filling equipment model 1 without adapter p/n 405 75 00 Cooling system vacuum filling equipment model 1A with adapter UA 50 p/n 403 36 00 p/n 405 75 50
F 04
Cooling system adapters
Adapters for connecting the radiator and/or expansion tank to the test set. All caps with connection for quick-coupler. For these fit: Radiator pressure pump model S-SK 2 p/n 404 15 00 Radiator pressure pump model S-SK 1 p/n 404 14 50 Radiator pressure pump model K-SK p/n 404 14 60
Adapter model SK Suitable for pumps with bayonet cap or clamping catch. This adapter makes it possible to change the pumps for the quick-coupler system. Adapter model SK p/n 404 19 00
Flexible connector SK 600 mm long with quick-coupler. This distance piece is required everywhere when the pump cannot be put directly onto the radiator and/or expansion tank. Flexible connector SK p/n 404 63 00
Cooling system adapter model UA 60J For radiator opening Ø of 18 - 24 mm With quick-coupler Because of the adjustable bridge with gripper jaws this adapter fits most different makes. Type : Daihatsu, Ford Probe, Honda, Hyundai, Isuzu, Kia, Mazda, Mitsubishi, Nissan, Opel Monterey, Subaru, Toyota, VW Taro Cooling system adapter model UA 60J p/n 404 66 00
Cooling system adapter UA 50 Ø 20 till 40 mm, with quick-coupler The special 3 stepped construction made from flexible material, which deforms ball-like when in a strained condition, permits safe locking of the cooling system opening. Rough adjustment takes place through manipulation of the hand wheels. It is also possible to make micro-adjustments by use of the tightening screw. Type : Universal Cooling system adapter UA 50 p/n 403 36 00
F 09
Cooling system adapter KS 74 Adapter with quick-coupler for connecting the pressure pump and expansion tank Type: Toyota and Fiat Sedici Cooling system adapter KS 74 p/n 404 67 40
Cooling system adapter KS 77 W Adapter with angled connector, hose and quick-coupler to connect the cooling system with the radiator pressure pump. Type: Opel Zafira B from 2005 Cooling system adapter KS 77 W p/n 404 67 75
Cooling system adapter KS 79.1 Adapter with quick-coupler to connect the radiator pressure pump
and the expansion tank. Type: MB Sprinter from 2006 Cooling system adapter KS 79.1 p/n 404 67 950
Cooling system adapter KS 82.2 Adapter with quick-coupler to connect the cooling system with the radiator pressure pump. Type: MB B class Cooling system adapter KS 82.2 p/n 404 68 250
Cooling system adapter KS 100 Adapter with quick-coupler to connect the cooling system with the radiator pressure pump. Type: Fiat Idea and Panda Cooling system adapter KS 100 p/n 404 70 00
F 10
Cooling system adapter model H Adjustable from Ø 19,5 - 60 mm
Direct connection to the pump: Radiator pressure pump model S-SK 2 p/n 404 15 00 Radiator pressure pump model S-SK 1 p/n 404 14 50
Connection only in connection with adapter KS p/n 404 19 00: Radiator pressure pump model SV p/n 404 14 00 Radiator pressure pump model SD-V p/n 404 13 00
Model H Type Colour Ø from - to mm 11 red 21,0-38,0 p/n 403 35 10 12 Japanese red 19,5-38,0 p/n 403 35 20 13 Standard black 27,0-42,0 p/n 403 35 30 14 Audi, Opel, grey 33,0-50,0 p/n 403 35 40 Scania, VW 15 MB grey 26,0-45,0 p/n 403 35 50 16 MAN, Krupp blue 40,0-65,0 p/n 403 35 60
Cap test adapter DP With quick-coupler for testing the cooling system caps during error tracing.
DP 77 Type : Opel Vectra C from `02 p/n 404 17 70 DP 78 Type : Mini Cooper S p/n 404 17 80 DP 79 Type : MB Vivano `03.03- p/n 404 17 90 DP 84 Type : BMW 5er `06.03- p/n 404 18 40 DP 85 Type : Ford C-Max, Volvo S40 `09.03- p/n 404 18 50 DP 90 Type : Kia, Smart For Four p/n 404 18 80
Cap test adapter set Light cap test adapters made from impact resistant plastic with quick-coupler for testing the cooling system caps during error tracing.
DP 1 Type : Standard DP 18 Type : Japanese vehicles, Ford, MAN, Opel, VW DP 23/26 Type : Alfa, Chrysler, Citroen, Fiat, Honda, Opel, Peugeot, Renault DP 31 Type : Daewoo, Ford, Jaguar, Opel, Rover, Skoda DP 32 Type : BMW, Rover DP 38 Type : VW DP 62 Type : Audi, Ford, Porsche, Seat, VW, Smart DP 65 Type : Audi, VW DP 81 Type : MB For types see cooling system adapter list.
DP 1 bayonet cap p/n 404 16 05 DP 18 bayonet cap p/n 404 13 35 DP 23/26 p/n 404 12 35 DP 31 p/n 404 13 15 DP 32 p/n 404 13 25 DP 38 p/n 404 13 85 DP 62 p/n 404 14 85 DP 65 p/n 404 16 50 DP 81 p/n 404 18 15 Cap test adapter set 9 pcs. p/n 405 61 50 in a plastic case
F 11
Battery acid examiner This equipment allows quick and simple examination of the anti freeze levels, the windshield washer fluid and the battery acid. The anti freeze examination can be made instantly, i.e. independent of the temperature of the coolant (cold or hot). For precise measurement a drop of coolant, windshield washing water and/or battery acid is sufficient. With optimal optical adjustment to allow visual perception by sharpness attitude. Supplied in a carrying bag, with pipette and detailed operating instructions.
Coolant and battery acid examiner p/n 420 00 05
Battery acid examiner This equipment allows quick and simple examination of the anti freeze levels, the windshield washer fluid and the battery acid. The anti freeze examination can be made instantly, i.e. independent of the temperature of the coolant (cold or hot). For precise measurement a drop of coolant, windshield washing water and/or battery acid is sufficient. With optimal optical adjustment to allow visual perception by sharpness attitude. Supplied in a carrying bag, with pipette and detailed operating instructions.
Coolant and battery acid examiner p/n 420 00 00
Battery acid examiner Hand refractometer, go anywhere equipment for examination of the anti freeze levels, the windshield washer fluid and battery acid. Measuring range Ethandiol (ethyl glycol) 0°to-50°C, Propandiol (propylene glycol) 0°to -50°C, battery acid 1.15 to 1.30 g/ml. High-quality quality, zero-line adjustment, visual perception attitude on the eyepiece. Sturdy metal housing. In a hard plastic box including a mini screwdriver for adjustment and a pipette. Coolant and battery acid examiner model Japan OTC p/n 920 00 00
Cylinder head leak tightness tester model SK With quick-coupler connectable to all Pichler cooling system adapter caps and universal plugs. For water-cooled combustion engines. The regenerating test liquid used in this equipment discolours automatically with leakage and ensures accurate inspection results. Cylinder head leak tightness tester p/n 405 25 00 Special test liquid 250 cm³ p/n 405 00 10 Spec. cleaning and rinsing agent 250 cm³ p/n 405 00 30
F 12
Staff thermometer Scale -Ø 63 mm Metering range 0 - 120°C. To check the water temperature. Indispensable for the examination of thermostats, the vehicle temperature display and the water pump. Gr. 1 Dipping shank -Ø 7 mm, 135 mm long. with seal, for adapter model SK. Gr. 2 Dipping shank -Ø 4 mm, 230 mm log. for adapter model H Staff thermometer size 1 p/n 404 24 00 Staff thermometer size 2 p/n 404 24 50
Hose clip pliers model F With flexible shaft (530 mm) For pulling together of ear clips on coolant and fuel hoses, cv joints etc. universally applicable, suitable for nearly all passenger car makes. No damage to the clip or hose. Problem-free, fast removal of coolant hoses. Hose clip pliers model F p/n 605 03 25 Repair kit (shaft, spring & gripper clamp) p/n 605 03 27
Hose clip pliers with “Cartouche principle " Universally applicable with 2/ 3 replaceable shafts.
Hose clip pliers with 2 different replaceable flexible shafts and clamps. A third shaft and clamp is available specifically for use on VAG models with new generation clips.
Flexible shaft "VAG" SZ3000 for the hose clip pliers p/n 905 03 15
Hose clip pliers for MUBEA clips For the extremely strong and new hose clips MU56 and MU65, which are mounted on VW Passat turbocharger suction hoses and on T5 water hoses. Also for other smaller clips e.g. MU25, MU26, MU27 and MU40 used on other vehicles. In order to make a professional disassembly and assembly of these clips the mechanic requires both of these large pliers. Hose clip pliers for MU25,MU26,MU27,MU40 p/n 905 02 93 Hose clip pliers for MU56,MU65 p/n 905 02 95
F 13
Hose clamp pliers "Clic" model V To open and close "CLIC" clamps. Because of the swivelling grab jaws the pliers are adaptable. Thus hard to reach clamps can be opened and closed without a problem. Type : e.g. Audi / VW, BMW, Opel etc. fuel pipes, cooling system, oil lines and windshield wiper system. Hose clamp pliers "Clic" model V p/n 605 02 30
Hose clamp pliers model ES for "CLIC" clamps Re-usable "CLIC" clamps are used throughout the motor industry. Be it at fuel pipes, on drive shafts, on negative pressure hoses or heater hoses, they are fitted everywhere. In order to be able to reach the clamps in the different installation positions for disassembly and assembly many different clamping pliers are offered. On this model the jaws are replaceable and rotatable. Thus the position of the pliers can be preset in order for optimal reach of the clamp. The markings on the jaws must always be lined up to each other! Hose clamp pliers model ES for "CLIC" clamps p/n 605 02 70
Hose clamp set For radiator hoses, plastic fuel pipes and many other non steel reinforced hoses. Hose clamp size 1 (up to 10 mm Ø) p/n 605 04 00 Hose clamp size 2 (up to 15 mm Ø) p/n 605 05 00 Hose clamp size 3 (up to 25 mm Ø) p/n 605 06 00 Hose clamp size 4 (up to 45 mm Ø) p/n 605 07 00 Hose clamp set 4 pcs p/n 605 08 00
G 01
Body work set model K Nine replaceable plastic impact heads with firmly integrated metal threaded inserts - Slide hammer 1kg. - All parts interchangeable. - Can be used as a slide hammer and with the knurled handle as a pure beating tool. Particularly suitably for steel, aluminium bodies and painted surfaces. It is possible by filing or grinding to modify the plastic heads. Body work set model K12 pcs. in a case p/n 655 75 00
Panel assortment for the body repair man This beautiful and high-quality set composed of three panel hammers with Hickory handles and four dolly’s is supplied in a plastic case. The perfect set for the craftsman who values the optimal relationship between price and quality. Panel set "HICKORY" 7 pcs p/n 955 09 00
Dolly set F Special dolly set for the stretch and shrink-free treatment of bodies made from normal, high-strength, special thin steel sheets and aluminium. Employment e.g.: door sheets, wing flaring and direct panel beating. A rubber-covered solid steel core provides for a full surface support during the sheet metal working. Used with pick irons for the best way results for colourless damage repair. Hand fist set F 7 pcs. p/n 655 77 00 Rubber dolly’s with steel core Even the smallest workshop is subject to new technologies. Here we offer dolly’s for aluminium bodies as well as for the treatment of high-strength, specially thin steel sheets in two versions. The dolly’s have a steel core and are covered with rubber. The advantages are: full surface support (more than with conventional steel dolly’s), can be used also for direct impact, arranges the sheet metal without stretch or shrink. Rubber truing blocks set 2 pcs with steel core p/n 955 22 20
G 02
Edge impact iron Ridge width 145 mm 450 mm long. For professional panel beating of edges and flares in hard to reach areas. This tool permits repair without damage to the edges. With a 4 sided grip to check the tool position in cavities. The edge impact iron can be folded up like a pocket knife, thus one can reach nearly every corner with the slim anvil blade e.g. in doors, at the tail sheet metal inside or in quarter panels. Because of the mobile blade the impact is always flat on the outer skin.
Edge impact iron p/n 655 14 00
Torque - panel hammer 1 side flexible-swivelling with spiral outline 42 mm Ø and 1 side smooth 31.5 mm Ø. For material thicknesses from 0,2 to 1.0 mm. Due to the particular design of the tightening yoke of the hammer the beating is converted into a rotating motion the fan-like surface of the hammer stretches the metal so evenly that neither the material condition nor material thickness are changed Torque - panel hammer p/n 655 05 90
Panel work system model 3 Slide hammer panel set Basic device with slide hammer 5 kg (thread M 18x1,5) p/n 614 87 90 Double hook, mobile p/n 653 55 30 Draw clamp on his own tightening p/n 653 62 00 Finger hook (draw hook "F") p/n 653 63 00 Reinforcement angle/pair (only with finger hook) p/n 653 64 00 Slide hammer panel set model 3 p/n 653 60 00
Pneumatic slide hammer Overall length 660 mm, slide weight 1800 g 2 rubber suction plates: size 1 Ø 155 mm, size 2 Ø 120 mm For the extraction of dents from body surfaces. Using the operating valve on the end of the handle the pressure drop and pressure build-up are regulated. With a compressor air bleed port of 6-8 bar traction power of 100 kg can be achieved. The aluminium grasp is equipped with hand guard and has auxiliary vents to ensure rapid air release. Pneumatic slide hammer p/n 655 20 00
G 03
Mini draw clamp Body work clamps quick and easy to install. For hard to reach places which have a small working surface. Mini draw clamp model 2 32 x 60 x 50 mm For lateral 90° course, without dumps and rotating. Mini draw clamp model 2 p/n 652 32 60
Special draw clamp These specially formed clamps allow work in hard to reach places of all stretching applications for the body repair man. Apart from the useful design this tool has enormous strength at the jaws. We have two models available so that as well as a flat muzzle form it is also possible to grip 90° bent sheet metals and to stretch them. Both draw clamps are provided with a neck slot head, which makes pulling possible when used with a double draw hook or with a chain or slide hammer. Draw clamp with flat cheeks for sheet metals with flat profile Draw over neck slot head p/n 900 16 30 Draw clamp with 90° cheeks for sheet metals with angular profile. Draw over neck slot head p/n 900 16 40
Triangle drawing equipment Model I-M500 and model X-M200 Special drawing equipment. Since the use of metal bodies on the automobile there have been many variations of draw clamps. The advantage of these devices is that they can be used on columns, hinges, in the shock strut cathedral in fact anywhere where it is possible to fasten with screws or pins. Triangle drawing equipment model X-M200 p/n 900 20 20 Triangle drawing equipment model I-M500 p/n 900 20 21 Triangle drawing equipment model X-M200 + I-M500 p/n 900 20 25
Pair of clamping latches in tongue form Additional equipment for the triangle hauling equipment The clamping jaws are used in connection with the triangle drawing equipment, corrugated for seizing round creases as e.g. within the door frame. Latch pair " tongue form " p/n 900 20 27
G 04
Draw hook thumb form This draw hook is a valuable and quick link to body work. Without the need to screw in this thumb hook can be inserted into a double draw hook and be used e.g. connected into the eye of a draw clamp. The downward facing tap prevents slippage of the hook. Dead weight 450 gram, maximum tensile load 3 tons. Draw hook thumb form in connection with double draw hook p/n 953 55 10
Twist/pulling equipment longitudinal channel front For stretching and truing the front longitudinal channel and the preparation of part replacement. The screw on plate with an interchangeable pull ring (M20) can be used on the left and right side. The device is screwed onto the bumper attachment. The hauling equipment is fixed with additional clamping devices to prevent detachment. Type: Audi A3, VW Golf IV Twist/hauling equipment longitudinal channel front p/n 652 10 50
Universal telescopic gauge This tool has extremely universal application possibilities due to the special shape and the offset clamping plates of the gap gauge. Because of this it is possible to close the hood or trunk lid with the gap gauge mounted. Also with non parallel running clamping edges the gap gauge can be used, as the clamping plates can also be tilted. Because of the strong construction it is possible, through pulling or pressing the mounted gap gauge to change the gap dimension before welding. Universal telescope gauge p/n 900 10 30
Grip wrench set 16 pcs Wrenches with rubber-covered handles. Apart from the special composition for body work each wrench is equipped with comfortable skid-proof and cooling restraining rubber grips for comfortable work. Grip wrenches set 16 pcs with rubber-covered handles p/n 900 50 00
G 05
Pneumatic rivet removing drill set With replaceable inserts and drills
To allow optimal drilling out of the very hard and variable diameter large rivets during the separation of sheet metals, this special pneumatic rivet removing drill set with 3 replaceable centring attachments and 2 different large " RIVET TWISTING BIT" drill inserts which are co-ordinated to commercially standard rivets.
Pneumatic rivet removing drill set with replaceable attachments and drills p/n 825 05 45
Spot welding drill Made from special steel. For the removal of spot welds in sheet metal work and body construction. Spot welding drill HSSE 8,0 mm Ø p/n 270 50 00
Pneumatic axial grinder Connection: 1/4" internal thread Operating pressure: 6 bar Air consumption: 285 l/min. Air outlet: in front Number of revolutions: 23000 1/Min. Weight: 600 g Particularly for the use of hard metal milling cutters with 6 mm shank. Pneumatic axial grinder p/n 820 50 00
Hard metal milling cutters One piece polished, for the machining of welding seams, point and MIG welds, hardened steel, casting etc. (for application in the pneumatic axial grinder) shank Ø 6 mm. Spherical shape 10 mm Ø p/n 670 01 00 Spherical shape 12 mm Ø p/n 670 01 20 Drip shape 10 x 16 mm p/n 670 21 00 Flame shape 8 x 20 mm p/n 670 10 80 Cylindrical shape 10 mm p/n 670 31 00 Hard metal milling cutters set 5 pcs p/n 670 50 00 Laser weld seam milling cutter With the laser welding seam milling cutter welding seams can be loosened during body work. Specific milling avoids material weakening and damage to the lacquer finish, this can not to be prevented when grinding welding seams. Misaligned laser welding seams can be followed with the help of the oval-formed base plate. The milling depth is adjusted with the help of a fine thread and a rubber locking mechanism which is infinitely variable; as a result a milling trough of the sheet metal behind it is prevented. Welding seam release tool for laser welded seams Laser weld seam milling cutter set with 2 spherical cutters and 2 plates p/n 960 80 50
G 06
Door hinge adjuster model W Specially formed correcting heads, applicable to many different vehicles. Using specially hardened steel for high rigidity. Because they are screwed into the handle a simple replacement of the correcting heads is possible.
Correcting heads:
Size 1 Type: Audi 80 /100, Ford Fiesta, DB 201&124, Opel, Renault R5 Size 2 Type: Audi 80 /100, Ford Fiesta, DB 201&124, Opel, Renault R5 Size 3 Type: VW Passat Size 4 Type: Citroën AX /ZX, Ford Escort / Sierra, Peugeot 205 / 405, Renault R5, VW Polo / Golf III Size 5 Type: Opel Corsa B bottom / Omega B top/bottom, doors front: Citroën Evasion, Fiat Ulysse, Peugeot 806 Size 6 Type: Opel Corsa B bottom / Omega B top/bottom, doors front: Citroën Evasion, Fiat Ulysse, Peugeot 806 Size 7 Type: Opel Corsa B top, VW-Passat, Peugeot, Fiat Size 8 Type: Opel Corsa B top, Audi A4, VW Passat 97 top Size 9 Type: Ford Galaxy, Seat Alhambra, VW Sharan Size 10 Type: Ford Galaxy, Seat Alhambra, VW Sharan
Parts: Jaw opening Side
Size 1 9 mm left p/n 654 28 01 Size 2 9 mm right p/n 654 28 02 Size 3 10 mm p/n 654 28 03 Size 4 12 mm p/n 654 28 04 Size 5 8 mm right p/n 654 26 63 Size 6 8 mm left p/n 654 26 64 Size 7 13 mm right p/n 654 26 61 Size 8 13 mm left p/n 654 26 62 Size 9 14 mm left p/n 654 28 08 Size 10 14 mm right p/n 654 28 09 Universal handle 400 mm long. p/n 654 28 20
Set compositions: Set Type: Correcting heads No. I Audi, DB, Opel size 1 & 2 p/n 654 26 50 No. II Ford, Renault size 1, 2 & 4 p/n 654 27 00 No. III Peugeot, Citroën size 4 p/n 654 27 10 No. IV VW size 3, 4 p/n 654 27 50 No. V Audi, VW size 1, 2, 3 & 4 p/n 654 28 00 No. VI Opel Corsa B bottom / Omega B top/bottom size 5 & 6 p/n 654 26 65 No. VII Opel Corsa B top, Audi A3/A4/A6, Passat size 7 & 8 p/n 654 26 60 No. VIII Ford Galaxy, Seat Alhambra, VW Sharan size 9 & 10 p/n 654 28 10 All sets include a handle.
Set complete 11 pcs size1 – size10 p/n 654 29 00
G 07
Hinge disassembly and assembly set Because of the laterally bent SW 12 ratchet handle it is easy to reach inaccessible door hinges. Also can be used on other disassembly and assembly work such as fenders, boot lids, hoods and similar body parts. The very short manufactured bits are held with a retaining ball surely and firmly in the ratchet head, a special spring prevents slipping through and allows safe working. The set contains bits 10,12,13 mm. with twelve-point , M8, M10, M12 in XZN, T40, T45 Torx as Inbus M7 and M8. Hinge disassembly and assembly set 12mm. drive with 10 different inserts p/n 954 45 60
Hinge repair set For the repair of worn hinges and for replacing worn out hollow spring pins with new larger diameter pins. The 3 edged titanium-nitrated special drill does not cut at the front and is cylindrically stepped. This ensures an accurate guidance of the drill and round drilling out of worn, oval hinge holes. Type : Opel Astra, Omega, Vectra etc. Hollow spring pin impact thorn 175 mm p/n 654 24 60 Special drill 3 edged, titanium-nitrated p/n 274 80 00 Slotted straight pin set Ø 8, (24 pcs) p/n 654 24 55 Hinge repair set in a plastic case p/n 654 24 50
Lock out set Extensive tool set to open locked vehicles. Different operating tools made of round steel bar; flat steel strip and plastic make it possible to unlock doors using the operating knob, the door lock linkage or the interior door handle. With the three-part 170 cm long "Long Jim" door handles are operated through the car interior. The two plastic wedges allow the entry of the tools. For illumination a staff flashlight is included. Lock out tool set complete. 22 pcs p/n 657 70 00 in an imitation leather bag Note: Store these door opener tools under lock and bold!
Air spreading cushion 150 X 150 mm For the careful raising and forcing delicate materials e.g. in the instrument panel, windows and while using of the lock out tools. The spread cushion is pushed between the door frame and the A pillar or between the side window and the door panel. By inflating the spread cushion a consistent gap is created without damage. In order to fix or extend the gap plastic wedges e.g. p/n. 6611055 can be inserted. Air spreading cushion p/n 957 76 50
G 08
Door upholstery release pliers Particularly slim “aggressive" muzzle form, slightly wedge-shaped. For damage-free removal of the clips on door linings and other vehicle linings. Door upholstery release pliers p/n 654 51 50
Door upholstery release pliers model XL Extra large version of 654 51 50 Predominantly for use with wide linings in the door and luggage compartment upholstery with lining plugs that have a large diameter e.g. in the Golf V this model is highly recommended. Door upholstery release pliers model XL p/n 654 51 60
Release lever set universal For the careful release of door linings, trim, armature linings and tie-clips without damaging. From break-proof but soft plastic so ideally suited to sensitive materials. Release lever set universal 4 pcs p/n 654 51 20
Hatch lining release lever 500 mm long. For the disassembly of hatch linings with difficult to reach retaining springs. The release lever directly seizes the retaining tie-clip and prevents damage of the lining. Type: Audi A3, A6, A4 Avant, VW Golf IV and Passat Variant Hatch lining release lever p/n 654 51 40
Combination assembly wedge model 1 22 x 270 mm, Groove side 15° bent, opening Ø 7,5 mm Slim universally applicable assembly wedge made from wear resistant plastic with groove. For the release of trim, protective caps, operating knobs, window pit borders and door linings. Combination assembly wedge model 1 p/n 611 11 70
Combination assembly wedge model 2 215 mm x 26 mm, groove ca 7,5mm, bent 45° Made from wear resistant plastic. For the release of trim, window pit borders and door linings. Type : Universal, specially MB trim clips Combination assembly wedge model 2 p/n 961 15 00
G 09
Trim disassembly board 350 x 180 x 16 mm. Specially formed assembly and disassembly board for trim. - Light shatter resistant plastic - Reciprocal chamfered induction bevel makes it possible to dismantle close lying trim - Broad low-cut grasp oval permits sensitive even lever off of long trim - Semicircular milled out back for pressing the trim in. Trim disassembly board p/n 655 50 00
Star screwdriver 200 mm long. For star screw heads with 5 slots, e.g. emblem (boot lid). Type : Saab, Seat, Volvo Star screwdriver p/n 501 20 00
Fender key model 3 T 30 x 300 mm. Particularly slim T-section key in special length. For the disassembly of the fender, without the disassembly of the door. The slot between the opened door and the A pillar does not permit thicker tools. Type : BMW E 38 For the headlight disassembly Type : Audi A 6, Renault Laguna (headlight adjustment) Fender key model 3 p/n 654 62 00
Wiper arm repair set For the repair of the rusted tight arm linkages Set consists of: Expressing fork for removing the safety moon rings. Special punch for deflecting extremely firm wiper axles. Wire brush for cleaning teeth at the wiper arm axle. T-grasp reamer for cleaning and finish-reaming of the locating hole. Package of snap rings (20 pcs) in “original size" Type : VW Golf 4, Audi A3, Seat, Skoda etc. Wiper arm repair set p/n 658 24 00 in a plastic box Refilling packing of snap rings (20 pcs) p/n 658 24 01
G 10
Wiper arm repair set model II For the repair of rusted tight wiper arm linkages. Set consists of: Expressing fork - Removing the snap rings. Punch - Deflecting the wiper axles Wire brush - Cleaning teeth. T-grip reamer - Cleaning and finish-reaming the locating hole. Package of snap rings (20 pcs) in " original size" Type: VW Sharan, Seat Alhambra, Ford Galaxy Wiper arm repair set model II p/n 658 25 000 in a plastic box Refilling packing of snap rings size II (20 pcs) p/n 658 25 010
Rear window washer repair set For repairing the rear window washer. With this tool the remainder of the broken off washer nozzle is drilled out of the windshield wiper axle and if necessary the broken brass tubing in the rear windshield wiper motor is repaired. By using the windshield wiper axle screw as a guide the milling cutter for removing the remaining nozzle or the drill for removing the remaining riser pipe is accurately positioned. The brass tubing is replaced by the enclosed plastic tubes..
Type : VW, Audi e.g. Golf IV, Passat, Sharan and Audi A4 Ford Galaxy, Seat Alhambra
Rear window washer repair set p/n 658 23 20
Plastic tubes 5 pcs. p/n 658 23 25
Plastic tubes 10 pcs p/n 658 23 30 Claw hook universal Applicable with slide hammer Impact weight 5 kg or 8 kg This hook model with a internal thread of M18x1.5 is universally applicable with our two slide hammers of 5 kg or 8 kg impact weight. Generally for rough panel work on the body and in the frame area, as well as for the disassembly of knuckles, tie rod joints, articulated bearings of wishbones etc. Claw hook universal p/n 953 55 30 Slide hammer complete 5kg p/n 614 87 90 Slide hammer complete 8kg p/n 614 88 00
G 11
Wiper arm extractor. For problem-free and damage-free extraction of windshield wiper arms.
P/n A B C D E F
Spindle Ball /
Hollow / Press. p.
6582232 22 29/31 20,5 3 29/31 35 K
6582235 10,5 26 41 4 29,4 35 H
6582240 14,2 27/25 23,4/41 4 27 33 B
6582245 11 26 42 3 29 35 B
6582250 14 - 45-51 3-7 - 45 P
6582255 23 49/36 13/27 6 49 57 -
6582257 14,2 27/25 23,4/41 4 27 33 B
6582260 21 24/27,5 10/21/34 4 27,5 34 B
6582265 12 54 34,8 6 54 60 B
6582270 26 34 29,4 3,7 34 42 B
6582280 22 29/31 20,5 3 29/31 35 B
6582285 10,5 37 27 3 40 47 B
9582272 38,5 46 43,5 2,5 46 52 P
9582812 37,5 43,5 45 4 43,5 52 H
9582815 14,2 27/25 23,4/41 4 27 33 H
9582820 23,5 29 27 4 30 37 B
9582823 14. 38 27 3 40 47 B
9582825 12 30 32 4 30 36,5 B
6582260H 21 28 10/21/34 4 28 34 H
Wiper arm extractor p/n 658 22 32* Type: e.g. Fiat Ulysse front, Peugeot 306, 406, 806 front Saab all models VW Golf IV, V front Wiper arm extractor p/n 658 22 35 Type : e.g. MB M,ML class rear, combi. models rear Peugeot 306, 806 rear Wiper arm extractor p/n 658 22 40* Type : e.g. Opel Astra G Caravan till 7.99 rear Peugeot 206, 307 rear VW Golf III, Polo old rear Wiper arm extractor p/n 658 22 45* Type : e.g. Citroën C3, C5, Xsara Break, Coupé, Picasso rear Opel Astra G Caravan from 7.99, Zafira rear Peugeot 307 SW rear Renault Clio, Espace, Megane Scenic rear Wiper arm extractor p/n 658 22 50* Type : e.g. Audi A3 front BMW E32,34,36,38,39 rear Ford Mondeo from 2000 front Wiper arm extractor p/n 658 22 55* Type : e.g. Chrysler Voyager rear Wiper arm extractor p/n 658 22 57* Type : e.g. Audi A4, A6 front Ford Focus front Opel Vectra rear Renault Megane rear VW general new models front
G 12
Wiper arm extractor p/n 658 22 60H Type : e.g. Audi A4, A6 rear Opel Corsa rear Seat Alhambra rear VW Golf IV Passat Variant, Sharan new models rear Wiper arm extractor p/n 658 22 60 Type : e.g. Citroën Xsara Break, Coupé front MB M class front VW Lupo, Bora, Polo rear Seat rear Skoda rear Wiper arm extractor p/n 658 22 65* Type : e.g. Renault Laguna Kombi from 2000, Megane Scenic
from 2000 rear Wiper arm extractor p/n 658 22 70 Type : e.g. Citroën C5 Break rear Ford Galaxy new models front Porsche Cayenne front Seat Alhambra new models front VW Sharan new models, Touareg front Wiper arm extractor p/n 658 22 80 Type : e.g. VW Golf V front Wiper arm extractor p/n 658 22 85* Type : e.g. Audi A4 from 2004 rear VW Golf V rear Wiper arm extractor p/n 658 22 72 Type : e.g. Porsche Cayenne rear VW Touareg rear Wiper arm extractor p/n 958 28 12* Type : e.g. Audi A3, A4, A6, Audi 80 rear Wiper arm extractor p/n 958 28 15 Type : e.g. Honda Civic from 2002 rear Wiper arm extractor p/n 958 28 20* Type : e.g. Citroën Xsara Picasso front Ford Mondeo new Traveller front Ford Mondeo new Limousine front Peugeot 206, 307, 307 SW Renault Espace ,Megane Scenic front Wiper arm extractor p/n 958 28 23 Type : e.g. Renault Megane front Wiper arm extractor p/n 958 28 25 Type : e.g. Citroën C5 from 2004, C5 Limousine rear Peugeot 407 rear * Wiper arm extractor set- 10 pcs p/n 958 28 00 in a case
G 13
Kombi two arm extractor Wiper arm & battery pole extractor. Universal, handy two-arm extractor with cone extraction device. Special tool for the extraction of battery pole clamps or to be used as a universal wiper arm extractor. Battery pole and Uni wiper arm extractor p/n 940 33 50
Rear wiper arm extractor UNI Renault Rear wiper arm extractor UNI set 6 pcs. With 2 extraction plates. Type : Renault all new models and universal. Rear wiper arm extractor Renault p/n 958 28 30
Wiper arm extractor two armed Universally applicable two armed extractor, auto centring. Wiper arm extractor two armed p/n 103 99 50
Wiper arm extractor Wiper arm extractor with lateral guidance. Pair of narrow arms for wiper arm extractor p/n 658 21 42 Pair of wide arms for wiper arm extractor p/n 658 21 43 Wiper arm extractor two armed with pair of wide arms p/n 658 21 41 Wiper arm extractor four armed p/n 658 21 40
Wiper arm extractor set. Universally applicable extractor set for the fast and damage-free disassembly of wiper arms. The wiper arm grip arms are used with a spindle.
Bridge with spindle Wiper arm extractor universal four armed p/n 658 21 40 7 wiper arm claws size 1 - size 7
Wiper arm extractor set in a case p/n 958 29 50 with 7 claws
Wiper arm extractor set. Universally applicable extractor set for the fast and damage-free disassembly of wiper arms. The wiper arm claws are used alternatively depending on the wiper construction with a slide hammer or spindle.
Type : Universal
Bridge with spindle (S) Bridge with slide hammer (H) Wiper arm claw size 1 opening 21,0 mm Wiper arm claw size 2 opening 23,8 mm Wiper arm claw size 3 opening 15,5 mm Wiper arm claw size 4 opening 22,0 mm Wiper arm claw size 5 opening 28,0 mm Wiper arm claw size 6 opening 18,8 mm Wiper arm claw size 7 opening 15,0 mm
Wiper arm extractor set in a case p/n 658 21 00 with 7 claws
G 14
Windscreen separation knife model M Release and blade grip made from aluminium with replaceable blade. For the cutting out of bonded windscreens. Operation by one man! (For non-fusible adhesives.) Repl. blade angle blade long wide No. 1 standard 90° 20 mm 8,5 mm p/n 658 51 00 No. 2 long 90° 36 mm 11,0 mm p/n 658 51 30 No. 4 pointed 90° 23 mm 3-8 mm p/n 658 51 40 Windscreen separation knife model M incl. stand. knife no.1 p/n 658 50 00 Windscreen separation knife model M set 5 pcs. p/n 658 51 50
Windshield assembly equipment For the problem-free installation of nearly all non-bonded windshields and for drawing in the trim. The trim drawing in tool can be adapted to different trims by the use of 5 different inserts. Three further tools for installing and cleaning e.g. glass remainders are contained in the set. Contents: Handle with 6 m cord Trim drawing in tool with 5 inserts Trim cleaning tool, for removing of glass remainders Hook tool, curved Hook tool, straight Windshield assembly equipment 5 pcs. p/n 657 35 00 in a plastic case
Pass through awl disk disassembly 280 mm lg. For puncturing the windscreen adhesive and for drawing in and drive through of the cutting wire during the disassembly of bonded windscreens. Passing through awl windscreens disassembly p/n 657 35 20
Auto glass disassembly set The set contains as well as the classical hand cutting tools with square cutting wire, a separation knife, a passing through awl, a cutting knife for removing the remaining adhesive, a universal scraper and a clip tool Auto glass disassembly set 8 pcs p/n 957 00 00 in a plastic case
G 15
Suction pad
For body attachment and windscreen fixing Suction pad p/n 658 20 00
Suction pad set model F Carrying capacity: 50 kg For lifting and transporting glass, for installation and removal of windscreens. Consists of two flexible lifting pads and a band. Vacuum lifting pad model F p/n 658 11 00 Tightening strap p/n 658 75 00 Vacuum lifting pad set model F, 2 pcs p/n 658 12 00
Suction pad set 2 pcs "MINI" Universally applicable, an aid for the extraction of small dents and body damage or when mounting bonded windows, fix of trim, emblems or tuning accessories. This set with a carrying capacity of 10-15 kg. per piece with a suction cup diameter of 57.0 mm is invaluable to any workshop.
Vacuum lifting pad set small, Ø57,0mm suction power 10-15 kg. p/n 958 11 50
Vacuum holder set Cup-Ø 60 mm, Steel retaining strap 280 mm long., rubber covered For fixing the side windows during work to the doors. The retaining strap is put over the door frame and fixed with the suction plates to the side window within the frame. Type : Universal Vacuum holder set 2 pcs p/n 658 11 50
Pneumatic one hand disc grinder This unique hand disc grinder functions in connection with fibre corundum grinding disks. The newly conceived 5" hole supporting disk permits a favourable view of the worked surface and special air cooling of the work area. Further advantages are speed regulation, lightness and ergonomically formed handle for easy use. Pneumatic one hand disc grinder "BELLA-VISTA" for 5 holes fibre corundum grinding disks. p/n 804 38 00
G 16
Scraper Handy scraper with a replaceable blade. The blade can be moved by a slider with slots in the grasp. For removing stickers etc. from glass panels. Scraper p/n 311 15 00 Spare blade p/n 311 11 00
Plastic chisel and scraper set With 100 spare blades The plastic chisel is particularly well suited to removing the stuck on weights from aluminium rims or for the disassembly of adhesive trim and the like. The scraper is only good as long as it is sharp, therefore we include in this set 100 spare blades. Also the handle is flexible therefore easy to modify depending upon the required application. Plastic chisel and scraper set p/n 311 10 05
Scraper and chisel set 4 pcs. This tool kit can be used either as scrapers or chisels. With solid continuous high-grade stainless steel blades (which can be reground). Ideally for removing plaques, stickers, adhesive detritus, seals etc., also as chisels for the separation of sheet metals and even spot welds. Scraper and chisel set 4 pcs. p/n 911 01 50
Universal scraper and cutter set This universal set should be in every workshop. Whether you are cutting, scraping, separating or removing this set always has the suitable tool. With blades in widths 12mm, 16mm, 20mm straight, a 16mm diagonal blade for the scraper handle with a screwed holder, or a trapezoid blade for the cutter you are sure to have the correct tool for the job.
Scraper set 27 pcs with replaceable blades p/n 911 05 00 In a plastic box
H 01
Torque wrench KS3 20NM to 200Nm 1/2" drive with push through head The work range of this 1/2” torque wrench is from 20NM - 200NM The scale with a display in Nm and lbs-ft is easily readable behind a window, the 36 fine tooth ratchet head has a push through knob. These torque wrenches have a test certificate meeting DIN EN ISO 6789 and have an accuracy of +/-3%. Torque wrench KS3 p/n 906 60 30
Precision micrometer screw gauge Spindle Ø: 8 mm, Measuring drum Ø: 20 mm. The spindle thread is completely hardened and polished. The measuring surfaces are lapped and have a locking ring, ratchet and adjusting nut. The handle, measuring drum diameter and case are matte-chromium plated. With screwed on insulating clamps and hardened measuring surfaces. Size 1 measuring range 0 - 25 mm p/n 402 00 10 Size 2 measuring range 25 - 50 mm p/n 402 00 20 Size 3 measuring range 50 - 75 mm p/n 402 00 30 Size 4 measuring range 75 - 100 mm p/n 402 00 40
Calliper gauge model ST Reading: 1/10 - 1/20 mm Measuring range: -150 mm Stainless steel (Inox) precision - calliper gauge (DIN 862) lockable. - cross points with depth measuring rod - back with thread table Calliper gauge model ST p/n 402 10 00
Disk brake calliper gauge Size1 Size2 Measuring range: 0 - 60 mm 0 - 90 mm Bill length: 85 mm 120 mm Reading: 1/10 mm 1/10 mm For determining the brake disk wear. With divided measuring carriage so when the strength of the brake disk is measured, the calliper gauge can be loosened from the brake disk, without the measure being adjusted. Disk brake calliper gauge size 1 p/n 402 20 00 Disk brake calliper gauge size 2 p/n 402 20 05
Flexible lamp model CMI Flexible lamp 410 mm long with protective pipe, mirror attachment and magnet. Flexible lamp model CMI p/n 901 03 00
H 02
Stethoscope
Flexible listening device for safe location of mechanical damage: Examples: Engine: Faulty valves and bearings. Differential: Running noise Alternator: Defective bearings Body: Creak and screeching noises etc. Stethoscope p/n 401 50 00
Endoscope model H Effective length = 1000 mm
Probe ∅ = 6 mm Bending radius = 30 mm At least distance = 10 mm Line of sight = 0° and 110° Brightness = up to 50000 lux in a distance of 16 mm Battery handle for 3 LR14 for approx. 10 hours of work time
For seeing into inaccessible places e.g. engine repair, error tracing, body parts etc. The flexible optical probe, based on optical fibre technology, has an outside diameter of 6.0 mm and can therefore be fed into small openings. So it makes it possible to look into the inside of the engine and into other difficult to access places in the vehicle e.g. transmission, doors, sun roof etc. without time-consuming disassembly work Endoscope model H1000 mm without mirrors p/n 966 70 06 Mirror 90° for endoscope p/n 966 70 90 Mirror 110° for endoscope p/n 966 71 10 Endoscope f. 12V p/n 966 70 16 Battery box p/n 966 15 00 Endoscope model H p/n 607 76 000 complete with mirror 110° in a plastic case
Borescope With a flexible 100cm long probe. With monitor for photo and video recordings The next generation of endoscopes brings this borescope with flexible probe. This has a diameter of 5.5 mm and a length of 1 meter. It is possible to store the captured picture as a photo or even a video recording which can then be viewed on the 3,5 “TFT LCD monitor with 240 pixels: The data can be uploaded also using USB interface or an SD-card onto a computer for further processing. To increase this tools efficiency there are also two optional screw on mirrors with 35° or 45° view angles. Borescope without mirror p/n 907 75 00 Mirror mountable on the probe 35° p/n 907 70 60 Mirror mountable on the probe 45° p/n 907 70 90
H 03
Measuring instrument and adjusting tool for bracket less " AEOROWISCHER" Systems To adjust of the new generation bracket less windshield wipers of Bosch, Valeo etc. Aero wiper arm measuring and adjusting tool basic device with 1 adapter p/n 95 82 400
Digital measuring equipment A collection of measuring and test tools including a digital calliper gauge a micrometer and dial gauge and a brake disk calliper gauge. Digital precision micrometer 0 - 25 mm p/n 402 00 15 Digital precision micrometer 25-50 p/n 402 00 25 Digital brake disk checking gauge 0 - 60 mm p/n 402 20 10 Digital calliper gauge 150 mm p/n 402 50 00 Digital dial gauge 0-10 mm diameter 55 mm p/n 430 10 50 Digital measuring equipment kit brake disk checking gauge, dial gauge and stand in a plastic case p/n 402 20 15
J 01
Car jack rubber attachment Disk with 140mm diameter These disks with their stepped receptacle are suitable for nearly all car jacks available in the trade. The 140 mm internal diameter has a cross slot for mounting at the door sill crease. Car jack rubber attachment UNI p/n 900 25 80
Twist Sockets short 6, 8, 10, 12 mm 1/4“ drive Sockets made from high-strength special steel with a self locking special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded hexagonal profiles. Twist-Sockets short p/n 913 00 04
Twist Sockets long 8, 10, 12, 14 mm 1/4“-Antrieb Sockets made from high-strength special steel with a self locking special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded hexagonal profiles. Twist sockets long p/n 913 00 05
Twist Sockets size 1 10 - 19 mm 3/8“ drive Sockets made from high-strength special steel with a self locking special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded hexagonal profiles. Twist sockets size 1 p/n 913 00 10 Twist Sockets 17 -22 mm, 1/2" drive
Sockets made from high-strength special steel with a self locking special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded hexagonal profiles. Twist sockets p/n 913 00 30
J 02
Twist Sockets size 2 19 -25 mm, 1/2" drive
Sockets made from high-strength special steel with a self locking special profile. For the release of screws, nuts, rim locks and socket head screws, whose drive profiles are damaged, e.g. rounded hexagonal profiles.. Twist Sockets size2 p/n 913 00 20
E profile Torx socket set long version/ 1/2" drive The 8 pcs set contains sizes with a 1/2" drive and 77 mm length: E10,E12,E14,E16,E18,E20,E22,E24 Outside Torx set 8 pcs long version p/n 788 10 05 in a plastic box
E profile double joint spanner set 5 pc double joint Torx E profile set containing individual sizes for diverse ranges of application. E6xE8 p/n 907 10 80 E10xE12 p/n 907 11 20 E14xE16 p/n 907 11 40 E18xE20 p/n 907 11 60 E22xE24 p/n 907 11 80 E profile double joint spanner set 5 pcs p/n 907 10 00 Gearwrench set With special bits A bit set to work in tight spaces. The double ratchet ring spanner 8x10mm can be easily used with the 30 short special bits Philips PH 0, 1, 2, 3 hex 4, 5, 6, 7, 8 XZN 5, 6, 8, 10 ,TX with and without tamper proof holes 10, 15, 20, 25, 27, 30, 40, 45 with a max. overall length of 22 mm. Gearwrench set p/n 970 50 00 Universal Gear plus adapter set This set is an ideal addition for customers who have our ratchet ring spanners, this adapter set consists of hex10mm:1/4" bit, hex10mm:1/4", hex13mm:3/8" and hex19mm:1/2" Adapter set 4 pcs. Gear plus p/n 926 00 50
J 03
Socket acceptance adapter set 3 pc. drill head to square 1/4", 3/8", 1/2" Socket acceptance adapter set p/n 926 01 00
Combination wrench set Extra-flat 10 till 22mm This combination wrench has several specific characteristics such as extra flat with a 3.0 mm thick hex 10mm spanner up to a 6.0 mm thick hex 22mm spanner and 12 pointed ring spanners bent 15°. Ideally suitably for machine repair or in the two-wheeler and bicycle repair range. Combination wrench flat set 10 pcs p/n 910 05 00
Impact release tool with joint attachment 1/2" Universally applicable impact release tool with overall length of 560 mm, a mobile 1/2" joint attachment for the attachment of different box spanners. Especially suitable for the loosening of the central nut during the disassembly of pulleys. Impact release tool 560 mm long, joint attachment 1/2" p/n 904 98 70
Joint socket set This set with sizes of 8, 9, 10, 12, 14, 16 mm. and a 3/8" drive is predominantly suitable for the disassembly and assembly of glow plugs. Additionally it is suitable for other areas of application in which a jointed socket can be used.
Joint socket set 6 pcs p/n 904 76 00 In a plastic case
Ribe screwdriver set Grip hexagon drive A 7 piece set of Ribe M4 to M10. The screwdrivers have a female hexagon at the handle end for strong operation and the blade passes through to the handle end.
Ribe screwdriver set p/n 902 52 00
J 04
Ratchet 72 teeth "Extra-flat" The advantage is in the detail of this ratchet series. For example a standard commercial 1/2" ratchet has a head diameter of approx. 38 mm; this version has one of 32 mm. The same is valid with the overall height; here the difference from a standard 1/2" ratchet is 33mm as oppose to 44mm. Ratchet 1/4" extremely slim head p/n 970 71 10 Ratchet 3/8" extremely slim head p/n 970 71 20 Ratchet 1/2" extremely slim head p/n 970 71 30
Socket wrench sets "TRIPLE-Plus“ ‘These ’TRIPLE Plus" socket sets it is possible to operate hexagonal, double hexagon, hex, E-Torx as well as metric and imperial sizes. Sets come with1/4" - 3/8" - 1/2" square drives and sockets in imperial or metric dimensions. Also available is the "TRIPLE Plus" passage socket wrench set for stay bolts etc. Socket wrench set "TRIPLE-Plus" 40 pcs, 1/4" drive p/n 920 23 50 Socket wrench set "TRIPLE-Plus" 47 pcs, short, long and bit sockets p/n 920 23 75 Socket wrench set "TRIPLE-Plus" 12 pcs, 50 mm long sockets 1/4" drive p/n 920 23 80 Socket wrench set "TRIPLE-Plus" 53 pcs, sockets and bits 3/8" drive p/n 920 23 85 Socket wrench set "TRIPLE-Plus" 22 pcs, ratchet, extensions, sockets 1/2" drive p/n 920 24 50 Socket wrench set "TRIPLE-Plus" 17 pcs passage sockets, adapter, ratchet, extension p/n 920 24 70
Socket wrench sets Socket wrench set "imperial sockets" 47 pc, sockets short and long with 1/4" drive p/n 920 22 20 Socket wrench combination set "metric/imperial" 99 pc sockets short and long, bit inserts, ratchets and extensions, grip in 1/4" and 3/8" drive p/n 940 12 50 Socket wrench set “Metric/imperial" 30 pcs, sockets short and long with a 1/2" drive p/n 943 55 00
"E" clips assortment and "E" clips setter These snap rings have versatile application in repair and production plants. The setters in the set have a holder and four replaceable inserts for 6, 7, 8, 9 mm clips. E clip assortment 300 pcs p/n 913 43 55 E clip setter set 5 pcs p/n 913 43 57
J 05
Punch set with hand guard This set of high-quality punches has several positive characteristics: Special material composition of the points which are not too soft so they do not bend and not too hard and brittle so they do not break or chip easily. With a soft plastic handle with additional hand guard. Dimensions 1.7/2.7/3.7/4.7/5.7/7.7 mm. Punch set with hand guard 6 pcs p/n 960 70 15 In a wallet
Combination wrench set extra long Strength savers as a higher torque is reached during disassembly/assembly. 6mm x 150 mm 15mm x 275 mm 7mm x 160 mm 16mm x 275 mm 8mm x 160 mm 17mm x 300 mm 9mm x 175 mm 18mm x 300 mm 10mm x 180 mm 19mm x 330 mm 11mm x 205 mm 20mm x 340 mm 12mm x 225 mm 21mm x 340 mm 13mm x 225 mm 22mm x 350 mm 14mm x 250 mm Combination wrench set 12 pcs p/n 711 03 00
E profile ring spanner straight Matt polished chrome vanadium steel in industrial quality. E profile ring spanner size 1 E 6 - E 8 p/n 716 00 60 E profile ring spanner size 2 E10 - E12 p/n 716 01 00 E profile ring spanner size 3 E14 - E18 p/n 716 01 40 E profile ring spanner size 4 E20 - E24 p/n 716 02 00 E profile ring spanner set 4 pcs p/n 716 00 00 Not contained in the set: E profile ring spanner E16 - E22 p/n 716 01 80
E profile ring spanner offset Industrial quality Ring spanner offset E 6 - E 8 p/n 716 10 60 Ring spanner offset E 7 - E 11 p/n 716 10 70 Ring spanner offset E 10 - E 12 p/n 716 11 00 Ring spanner offset E 14 - E 18 p/n 716 11 40 Ring spanner offset E 16 - E 22 p/n 716 11 60 Ring spanner offset E 20 - E 24 p/n 716 12 00 Ring spanner set offset 6 pcs. p/n 716 10 00
J 06
Combination ratchet ring spanner sets with 72 teeth Multigear Combination wrench 10mm short p/n 971 72 10 Combination wrench 11mm short p/n 971 72 11 Combination wrench 12mm short p/n 971 72 12 Combination wrench 13mm short p/n 971 72 13 Combination wrench 14mm short p/n 971 72 14 Combination wrench 15mm short p/n 971 72 15 Combination wrench 16mm short p/n 971 72 16 Combination wrench 17mm short p/n 971 72 17 Combination wrench 18mm short p/n 971 72 18 Combination wrench 19mm short p/n 971 72 19 Combination ratchet ring spanner set 10 pcs 10 till 19mm short version p/n 971 72 00 Combination wrench 8mm long p/n 971 71 08 Combination wrench 9mm long p/n 971 71 09 Combination wrench 10mm long p/n 971 71 10 Combination wrench 11mm long p/n 971 71 11 Combination wrench 12mm long p/n 971 71 12 Combination wrench 13mm long p/n 971 71 13 Combination wrench 14mm long p/n 971 71 14 Combination wrench 15mm long p/n 971 71 15 Combination wrench 16mm long p/n 971 71 16 Combination wrench 17mm long p/n 971 71 17 Combination wrench 18mm long p/n 971 71 18 Combination wrench 19mm long p/n 971 71 19 Combination ratchet ring spanner set 12 pcs 8 to 19mm long version p/n 971 71 00
Flex head combination ratchet ring spanner set Fork ring version with locking device The flex head is lockable in all positions The adapters can be used as ratchet with locking in 1/4" , 3/8" and 1/2" and as bit adapter for 10.0 mm, 5/16" and 1/4" in connection with the wrenches. Flex head combination ratchet ring spanner set 12 pcs. 8-19mm in a case p/n 903 34 70 Flex head combination ratchet ring spanner set 18 pcs. 8-19mm in a case p/n 903 34 75
Double-ended ring spanner straight extra long 10 till 24mm High-quality extra long spanners for strength-saving working. 8 x 10mm 285 mm p/n 911 02 51 10 x 11mm 285 mm p/n 911 02 52 12 x 14mm 325 mm p/n 911 02 53 13 x 15mm 365 mm p/n 911 02 54 16 x 18mm 400 mm p/n 911 02 55 17 x 19mm 400 mm p/n 911 02 56 22 x 24mm 435 mm p/n 911 02 57 Double-ended ring spanner straight set 7 pcs p/n 911 02 50 in a wallet
J 07
Double-ended off set ratchet ring spanner With fast switching pressure switch for on right of and left use. L thickness 10 x 11mm* 200 12 / 13 p/n 703 51 00 12 x 14mm* 230 11 / 12 p/n 703 51 20 13 x 17mm* 260 13,5 / 15 p/n 703 51 30 15 x 16mm* 260 15,5 / 15,5 p/n 703 51 50 19 x 22mm* 310 16 / 17 p/n 703 51 90 21 x 23mm 340 17 / 18 p/n 703 52 10 24 x 27mm 360 18 / 18 p/n 703 52 40 30 x 32mm 430 20 / 20 p/n 703 53 00 Double-ended ratchet ring spanner set* 5 pcs p/n 703 50 00
Double-ended ratchet ring spanner E profile "extra flat" Straight: L thickness E4 x E6 108 7,5 p/n 703 20 10 E6 x E8 108 7,5 p/n 703 20 20 E10 x E12 134 9 p/n 703 20 30 Off set: L thickness E4 x E6 108 7,5 p/n 703 21 10 E6 x E8 108 7,5 p/n 703 21 20 E10 x E12 128 9 p/n 703 21 30
Socket wrench set 1/4" Profile Super Lock Change-over quick release ratchet with insert, turning grasp, sliding grasp and universal joint, 1/4" square adapter x hex and 50, 100, flex. 145 mm extensions for each. Socket Super Lock 4, 4.5, 5, 5.5 6, 7, 8, 9, 10, 11, 12, 13, 14mm Insets T profile tamper proof sockets T10, T15, T20, T25, T30, T40 Phillips sockets size 1, 2, 3 Pozidrive bit sockets size 1, 2, 3 Slotted bit head sockets size 4, 5.5, 7 Hex bit sockets 3, 4, 5, 6, 7, 8 mm Angle allen key, 2, 2.5 Socket wrench set 1/4" 46 pcs Super Lock p/n 720 22 00
Torx socket set Torx sockets short 3/8“ drive E 6, 8, Torx sockets short 1/2“ drive E 10, 12, 14 Torx sockets long 3/8“ drive E 6, 8 Torx sockets long 1/2“ drive E 10, 12, 14 Reduction adapter; 1/2“– 3/8“ Angle extension 1/2“
Torx socket set 12 pcs p/n 788 25 00
J 08
Socket wrench set 1/4" Surface drive Change-over quick release ratchet with turning handle, sliding handle and universal joint. With 50 and 100 mm extensions and a 150 mm flex extension. Socket surface drive short. 4 , 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14 mm Socket surface drive long. 6, 7, 8, 10, 11, 12, 13 mm Inserts T profile bit sockets tamper proof T10, T15, T20, T25, T30, T40 Phillips bit sockets size 1, 2, 3 Pozidrive bit size 1, 2, 3 Slotted head bit sockets size 4, 5.5, 7 mm Hex bit sockets 3, 4, 5, 6, 7, 8mm Angle allen key 1.27, 1.5, 2, 2.5 Socket adapter 1/4“ square x 1/4“ hexagon for a electric screwdriver Socket wrench set 1/4", 53-tlg p/n 920 22 00
Change-over ratchet model B Robust workshop quality, polished chrome vanadium. Change-over ratchet model B 1 1/4" � drive 125 mm lg. p/n 770 70 10 Change-over ratchet model B 2 3/8" � drive 175 mm lg. p/n 770 70 20 Change-over ratchet model B 3 1/2" � drive 250 mm lg. p/n 770 70 30 Change-over ratchets model B set 3 pcs p/n 770 70 50 Flexible change-over ratchet model G 1 1/4" � drive 165 mm lg. p/n 770 60 10 Flexible change-over ratchet model G 2 3/8" � drive 265 mm lg. p/n 770 60 20 Flexible change-over ratchet model G 3 1/2" � drive 330 mm lg. p/n 770 60 30 Flexible change-over ratchets model G set 3 pcs p/n 770 60 50 Ratchet repair kits for model B und G: Repair kit 1/4" � drive p/n 770 72 10 Repair kit 3/8" � drive p/n 770 72 20 Repair kit 1/2" � drive p/n 770 72 30
Turning head ratchet 3/8" 3/8" � drive, 260 mm long. Fine toothed pass through ratchet for difficult to reach screw connections e.g. glow plugs, fenders, manifolds and starter motors. The swivel joint can be locked in any position. Also can be used as a stroke ratchet. Turning head ratchet 3/8" p/n 730 30 00
Power bar 1/2" 1/2" � drive The ideal aide e.g.: wheel assembly, wheel hub nuts, shock-mount screws, etc. Hinge handle 280 mm long. p/n 741 10 90 Hinge handle 610 mm long. "Extra Long" p/n 741 10 00
J 13
Angle extensions Special extension, with 30° tilt for work in hard to reach places. Size 0 1/4" � drive 25 mm long p/n 721 20 10 Size 1 3/8" � drive 32 mm long p/n 731 20 10 Size 2 3/8" � drive 75 mm long p/n 731 20 20 Size 3 3/8" � drive 125 mm long p/n 731 20 30 Size 4 3/8" � drive 250 mm long p/n 731 20 40 Size 5 3/8" � drive 450 mm long p/n 731 20 50 Size 7 1/2" � drive 52 mm long p/n 741 20 10 Size 8 1/2" � drive 125 mm long p/n 741 20 30 Size 9 1/2" � drive 250 mm long p/n 741 20 60 Size 10 1/2" � drive 500 mm long p/n 741 20 80
4 mm. p/n 780 20 40 5 mm. p/n 780 20 50 6 mm. p/n 780 20 60 7 mm. p/n 780 20 70 8 mm. p/n 780 20 80 9 mm. p/n 780 20 90 10 mm. p/n 780 21 00 11 mm. p/n 780 21 10 13 mm. p/n 780 21 30
Universal joint socket double hexagon set 9 pcs in a sheet steel case p/n 780 22 00
Universal joint socket double hexagon 3/8" � drive 10 * mm. p/n 780 31 00 11 * mm. p/n 780 31 10 12 * mm. p/n 780 31 20 13 * mm. p/n 780 31 30 14 * mm. p/n 780 31 40 15 * mm. p/n 780 31 50 16 mm. p/n 780 31 60 17 * mm. p/n 780 31 70 18 mm. p/n 780 31 80 19 * mm. p/n 780 31 90 Universal joint socket double hexagon set* 8 pcs on a rail p/n 780 30 00
J 16
Universal joint socket hexagon 3/8" � drive x 75 mm long Socket inside depth 10 mm. 31 mm p/n 782 51 00 11 mm. 31 mm p/n 782 51 10 12 mm. 31 mm p/n 782 51 20 13 mm. 31 mm p/n 782 51 30 14 mm. 31 mm p/n 782 51 40 15 mm. 31 mm p/n 782 51 50 16 mm. 31 mm p/n 782 51 60 17 mm. 31 mm p/n 782 51 70 18 mm. 31 mm p/n 782 51 80 19 mm. 31 mm p/n 782 51 90 Universal joint socket model L set, 10 pcs p/n 782 50 50 on a rail
Universal joint socket double hexagon 3/8" � drive Short (45 to 50mm long) universal joint socket for hard to reach places. Suitable for hexagon and the new double hexagon - profiles. 8 mm. 14 mm. 9 mm. 15 mm. 10 mm. 16 mm. 11 mm. 17 mm. 12 mm. 18 mm. 13 mm. 19 mm. Universal joint socket set 12 pcs. p/n 780 22 50 in a sheet steel case
Crow ring spanner double hexagon Crow ring spanner set open 4 pcs double hexagon on a rail 1/2“ drive-23, 24, 25, 26 mm p/n 935 10 00
Flexible open ring spanner 8x130, 9x130, 10x130, 11x150, 12x150 Open ring spanner with hexagon /double hexagon with knuckle
Special slim version, for the release/tightening of screw connections on fuel and hydraulic lines. Because of the knuckle and the slim construction it is also possible to use them where there is little room to work. Flexible open ring spanner set, 5 pcs p/n 905 09 000 Flexible open ring spanner 14mm p/n 905 09 140 Flexible open ring spanner 17mm p/n 905 09 170 Flexible open ring spanner 19mm p/n 905 09 190
J 17
Crow ring spanner 3/8" � drive Very slim for inaccessible line screw connections. 10mm. p/n 735 11 00 11mm p/n 735 11 10 12mm p/n 735 11 20 13mm p/n 735 11 30 14mm p/n 735 11 40 15mm p/n 735 11 50 16mm p/n 735 11 60 17mm p/n 735 11 70 18mm p/n 735 11 80 19mm p/n 735 11 90 Crow ring spanner, set 10 pcs on a rail p/n 735 10 00
Crow ring spanner set 8mm – 19mm 3/8” drive 21mm – 24mm 1/2”drive Crow ring spanner set* 15 pcs p/n 735 00 00
T-profile bit sockets 1/4" � drive x 32 long not tamper proof T 10 p/n 729 11 10 T 27 p/n 729 11 27 T 15 p/n 729 11 15 T 30 p/n 729 11 30 T 20 p/n 729 11 20 T 40 p/n 729 11 40 T 25 p/n 729 11 25 T-profile bit sockets 7 pcs on a rail p/n 729 11 00
T-profile bit sockets 3/8" � drive x 50mm.
Made from high alloy special steel. T 9 p/n 788 10 09 T 30 p/n 788 10 30 T 10 p/n 788 10 10 T 40 p/n 788 10 40 T 15 p/n 788 10 15 T 45 p/n 788 10 45 T 20 p/n 788 10 20 T 50 p/n 788 10 50 T 25 p/n 788 10 25 T 55 p/n 788 10 55 T 27 p/n 788 10 27 T-profile bit sockets 11 pcs on a rail p/n 788 12 00
J 18
T profile bit sockets 1/2"� drive x 55mm.
Made from high alloyed special steel. T20 p/n 788 82 00 T45 p/n 788 84 50 T25 p/n 788 82 50 T50 p/n 788 85 00 T27 p/n 788 82 70 T55 p/n 788 85 50 T30 p/n 788 83 00 T60 p/n 788 86 00 T40 p/n 788 84 00 T-profile bit sockets 9 pcs on a rail p/n 788 88 00
Special composition special sizes for motor vehicle special screws A 38 pieces assortment with specific tools for working on the special screws used in newer motor vehicle types. Like e.g.: T profile; T 60, T70 and T80 or T30 length 300 mm. XZN M16 tamper proof and M18x100 drive ¾“, Ribe M7x240, M8x240 M10x140 and M9x100, hex bit sockets 5x160 with ballpoint etc. Special composition special sizes 38 pieces p/n 988 24 00
T-profile bit sockets 1/2" � drive. Made from high alloy special steel. T 20 95 mm long p/n 788 52 00 T 25 95 mm long p/n 788 52 50 T 30 120 mm long p/n 788 53 00 T 40 120 mm long p/n 788 54 00 T 45 120 mm long p/n 788 54 50 T 50 120 mm long p/n 788 55 00 T 55 140 mm long p/n 788 55 50 T 60 120 mm long p/n 788 56 00 T 70 115 mm long p/n 788 57 00 T-profile bit sockets 9 pcs in a plastic case p/n 788 51 10
E profile bit sockets 1/4" � drive x 22 mm long E profile bit socket E 4 p/n 729 00 40 E profile bit socket E 5 p/n 729 00 50 E profile bit socket E 6 p/n 729 00 60 E profile bit socket E 7 p/n 729 00 70 E profile bit socket E 8 p/n 729 00 80 E profile bit socket E 10 p/n 729 01 00 E profile bit sockets set 6 pcs on a rail p/n 729 00 00
E profile bit sockets 3/8" � drive x 26 mm long Sockets profile E 4 p/n 788 30 04 Sockets profile E 10 p/n 788 30 10 Sockets profile E 5 p/n 788 30 05 Sockets profile E 11 p/n 788 30 11 Sockets profile E 6 p/n 788 30 06 Sockets profile E 12 p/n 788 30 12 Sockets profile E 7 p/n 788 30 07 Sockets profile E 14 p/n 788 30 14 Sockets profile E 8 p/n 788 30 08 Sockets profile E 16 p/n 788 30 16
E profile bit sockets set 10 pcs on a rail p/n 788 30 30
E profile bit sockets 3/8" � drive x 55 mm long Sockets profile E 4 p/n 788 36 04 Sockets profile E 10 p/n 788 36 10 Sockets profile E 5 p/n 788 36 05 Sockets profile E 12 p/n 788 36 12 Sockets profile E 6 p/n 788 36 06 Sockets profile E 14 p/n 788 36 14 Sockets profile E 7 p/n 788 36 07 Sockets profile E 16 p/n 788 36 16 Sockets profile E 8 p/n 788 36 08
E profile bit sockets set 9 pcs on a rail p/n 788 36 50
E profile bit sockets 1/2" � drive E 10 x 36 mm p/n 788 31 00 E 18 x 37 mm p/n 788 31 80 E 11 x 37 mm p/n 788 31 10 E 20 x 37 mm p/n 788 32 00 E 12 x 37 mm p/n 788 31 20 E 22 x 37 mm p/n 788 32 20 E 14 x 37 mm p/n 788 31 40 E 24 x 40 mm p/n 788 32 40 E 16 x 37 mm p/n 788 31 60
E profile bit sockets, set 9-tlong p/n 788 10 00 in a steel box
E profile bit sockets "long " 1/2" � drive x 77 mm long E 10 p/n 788 41 00 E 16 p/n 788 41 60 E 12 p/n 788 41 20 E 18 p/n 788 41 80 E 14 p/n 788 41 40 E 20 p/n 788 42 00 E profile bit sockets set 6 pcs on a rail p/n 788 43 00
J 20
E profile universal joint sockets 3/8" � drive E profile universal joint sockets E 6 p/n 780 70 60 E profile universal joint sockets E 8 p/n 780 70 80 E profile universal joint sockets E 10 p/n 780 71 00 E profile universal joint sockets E 12 p/n 780 71 20 E profile universal joint sockets E 14 p/n 780 71 40 E profile universal joint sockets set 5 pcs p/n 780 72 00 on a rail
Hex bit socket 3/8" � drive 3 44 mm long p/n 790 00 30 4 44 mm long p/n 790 00 40 5 44 mm long p/n 790 00 50 5 160 mm long p/n 790 01 50 6 44 mm long p/n 790 00 60 6 55 mm long p/n 790 03 60 6 220 mm long p/n 790 01 60 8 44 mm long p/n 790 00 80 8 100 mm long p/n 790 01 80 10 44 mm long p/n 790 01 00 10 155 mm long p/n 790 02 10
Hex bit universal joint socket 3/8" � drive x 62 mm long
Tilt-free bit sockets for hex screws Hex bit socket 5 p/n 786 00 50 Hex bit socket 6 p/n 786 00 60 Hex bit socket 7 p/n 786 00 70 Hex bit socket 8 p/n 786 00 80 Hex bit socket 10 p/n 786 01 00 Hex bit socket 12 p/n 786 01 20 Hex bit universal joint sockets set 6 pcs p/n 786 11 50
J 21
Hex bit ballpoint sockets 3/8" � drive x 100 mm lg. Hex bit ballpoint socket 4 p/n 790 72 40 Hex bit ballpoint socket 5 p/n 790 72 50 Hex bit ballpoint socket 6 p/n 790 72 60 Hex bit ballpoint socket 7 p/n 790 72 70 Hex bit ballpoint socket 8 p/n 790 72 80 Hex bit ballpoint sockets 5 pcs. p/n 790 73 00 on a rail
XZN bit socket Spanner size length � drive 4mm 25 mm 1/4 " p/n 791 00 04 4mm 125 mm 1/4 " p/n 791 00 14 8mm 93 mm 3/8" p/n 791 10 80 10mm 93 mm 3/8" p/n 791 11 00 5mm 60 mm 1/2" p/n 791 20 50 6mm 60 mm 1/2" p/n 791 20 60 6mm 100 mm 1/2" p/n 791 30 60 7mm 53 mm 1/2" p/n 791 20 70 8mm 60 mm 1/2" p/n 791 20 80 8mm 100 mm 1/2" p/n 791 30 80 8mm 120 mm 1/2" p/n 791 40 80 10mm 60 mm 1/2" p/n 791 21 00 10mm 100 mm 1/2" p/n 791 31 00 10mm 120 mm 1/2" p/n 791 41 00 10mm 180 mm 1/2" p/n 791 42 00 12mm 60 mm 1/2" p/n 791 21 20 12mm 100 mm 1/2" p/n 791 31 20 12mm 140 mm 1/2" p/n 791 41 20 14mm 60 mm 1/2" p/n 791 21 40 14mm 100 mm 1/2" p/n 791 31 40 16mm 60 mm 1/2" p/n 791 21 60 16mm 100 mm 1/2" p/n 791 31 60 16mm tamper proof 60 mm 1/2" p/n 791 51 60
Ribe bit socket 1/2" � drive 5mm 63 mm lg p/n 792 10 50 6mm 63 mm lg p/n 792 10 60 8mm 63 mm lg p/n 792 10 80 10mm 63 mm lg p/n 792 11 00 12mm 63 mm lg p/n 792 11 20 12mm 120 mm lg p/n 792 21 20 14mm 63 mm lg p/n 792 11 40 14mm 100 mm lg p/n 792 21 40 16mm 63 mm lg p/n 792 11 60
J 22
Rail set 400 mm long., 15 clamps each Rails for sockets, spring steel, chromed. Rail 1/4 " � drive p/n 740 60 10
Rail 3/8" � drive p/n 741 60 10
Rail 1/2" � drive p/n 742 60 10
Rail set 3 pcs p/n 742 60 50
T profile bits not tamper proof 30 mm long. Bit T 20 p/n 570 62 00 Bit T 40 p/n 570 64 00 Bit T 25 p/n 570 62 50 Bit T 45 p/n 570 64 50 Bit T 27 p/n 570 62 70 Bit T 50 p/n 570 65 00 Bit T 30 p/n 570 63 00 Bit T 55 p/n 570 65 50 75 mm long. Bit T 20 p/n 570 72 00 Bit T 45 p/n 570 74 50 Bit T 25 p/n 570 72 50 Bit T 50 p/n 570 75 00 Bit T 27 p/n 570 72 70 Bit T 55 p/n 570 75 50 Bit T 30 p/n 570 73 00 Bit T 60 p/n 570 56 00 Bit T 40 p/n 570 74 00 Bit T 70 p/n 570 57 00
T profile bits tamper proof 30 mm long. Bit T 20 p/n 570 42 00 Bit T 40 p/n 570 44 00 Bit T 25 p/n 570 42 50 Bit T 45 p/n 570 44 50 Bit T 27 p/n 570 42 70 Bit T 50 p/n 570 45 00 Bit T 30 p/n 570 43 00 Bit T 55 p/n 570 45 50 75 mm long. Bit T 20 p/n 570 52 00 Bit T 40 p/n 570 54 00 Bit T 25 p/n 570 52 50 Bit T 45 p/n 570 54 50 Bit T 27 p/n 570 52 70 Bit T 50 p/n 570 55 00 Bit T 30 p/n 570 53 00 Bit T 55 p/n 570 55 50
Ribe socket set 1/2“□ drive M6 till 16 Ribe socket set p/n 992 10 00 On a rail
J 23
RIBE bit socket set M5 till M14 tamper proof ½“drive length 110mm RIBE bit socket set 9 pcs. p/n 970 59 70 On a rail
Ribe bits hexagon 10mm 30mm long Bit Ribe 4mm p/n 570 58 04 Bit Ribe 8mm p/n 570 58 08 Bit Ribe 5mm p/n 570 58 05 Bit Ribe 10mm p/n 570 58 10 Bit Ribe 6mm p/n 570 58 06 Bit Ribe 12mm p/n 570 58 12 Bit Ribe 7mm p/n 570 58 07 75mm long Bit Ribe 4mm p/n 570 59 04 Bit Ribe 8mm p/n 570 59 08 Bit Ribe 5mm p/n 570 59 05 Bit Ribe 10mm p/n 570 59 10 Bit Ribe 6mm p/n 570 59 06 Bit Ribe 12mm p/n 570 59 12 Bit Ribe 7mm p/n 570 59 07
XZN bits 30mm long Bit XZN 5mm p/n 570 00 50 Bit XZN 10mm p/n 570 01 00 Bit XZN 6mm p/n 570 00 60 Bit XZN 12mm p/n 570 01 20 Bit XZN 8mm p/n 570 00 80 75mm long Bit XZN 5mm p/n 570 10 50 Bit XZN 10mm p/n 570 11 00 Bit XZN 6mm p/n 570 10 60 Bit XZN 12mm p/n 570 11 20 Bit XZN 8mm p/n 570 10 80
Hex bits 30mm long Bit hex 4mm p/n 570 20 40 Bit hex 8mm p/n 570 20 80 Bit hex 5mm p/n 570 20 50 Bit hex 10mm p/n 570 21 00 Bit hex 6mm p/n 570 20 60 Bit hex 12mm p/n 570 21 20 Bit hex 7mm p/n 570 20 70 75mm long Bit hex 4mm p/n 570 30 40 Bit hex 8mm p/n 570 30 80 Bit hex 5mm p/n 570 30 50 Bit hex 10mm p/n 570 31 00 Bit hex 6mm p/n 570 30 60 Bit hex 12mm p/n 570 31 20 Bit hex 7mm p/n 570 30 70
J 24
Mini bit reversible ratchet With live ring With the multiplicity of bits that are on offer in our program come these two mini bit ratchets as an ideal addition. The small construction, 15° bend, with switchover lever for left/right and the live ring, which makes manual operation of the loose or set screw possible, make this the ideal tool. The ratchets are equipped with a special holding device and have 1/4" and 5/16" drives to accept the available bits. Bit ratchet "MINI" 1/4" acceptance reversible with live ring p/n 906 11 40 Bit ratchet "MINI" 5/16" acceptance reversible with live ring p/n 906 11 60
Ball joint (tilt-free) "Impact" Ball joint 1/2" � drive 74 mm long p/n 794 60 10
Ball joint 3/4" � drive 105 mm long p/n 796 60 10
Ball joint 1" � drive 128 mm long p/n 797 60 10
Adapter "Impact" 3/8" � drive 1/4" � output 25 mm long p/n 793 70 10 3/8" � drive 1/2" � output 32,5 mm long p/n 793 70 20 1/2" � drive 3/8" � output 36 mm long p/n 794 70 10 1/2" � drive 3/4" � output 44 mm long p/n 794 70 20 3/4" � drive 1/2" � output 52 mm long p/n 796 70 10 3/4" � drive 1" � output 62 mm long p/n 796 70 30 1" � drive 3/4" � output 76 mm long p/n 797 70 10
J 25
Bits set hex / Torx „Impact“ With adapter ¾“ drive 10 pcs With this assortment we offer the truck, agricultural machinery and construction machine mechanic a top tool for the operation of larger screw sizes. Everything is in a sturdy wooden box with the s drive component ¾ “- drive 22mm hexagonal. The tools in the set have the following sizes: Torx T70, T80, T90, T 100. Hex 14mm, 17mm, 19mm, 22mm, 24mm. Additionally as an option we offer the hex bit size 17 mm with a length of 80 mm. This is needed for operation of the Lukas D3 brake assembly Bits set hex / Torx „Impact“10 pcs p/n 989 01 00 Impact bit hex 17 x 80 mm (Lukas brake assembly D3) p/n 989 01 70
Ball joint socket hexagonal "Impact" 3/8" � drive 10 mm 57 mm long p/n 782 61 00 11 mm 57 mm long p/n 782 61 10 12 mm 57 mm long p/n 782 61 20 13 mm 57 mm long p/n 782 61 30 14 mm 59 mm long p/n 782 61 40 15 mm 59 mm long p/n 782 61 50 16 mm 59 mm long p/n 782 61 60 17 mm 59 mm long p/n 782 61 70 18 mm 61 mm long p/n 782 61 80 19 mm 61 mm long p/n 782 61 90 22 mm 61 mm long p/n 782 62 20 24 mm 63 mm long p/n 782 62 40
Ball joint socket model "D" set 10 pcs p/n 781 20 50
Ball joint socket hexagonal "Impact" 1/2" � drive 13 mm 68 mm long p/n 782 71 30 14 mm 70 mm long p/n 782 71 40 15 mm 70 mm long p/n 782 71 50 16 mm 70 mm long p/n 782 71 60 17 mm 70 mm long p/n 782 71 70 18 mm 70 mm long p/n 782 71 80 19 mm 75 mm long p/n 782 71 90 21 mm 75 mm long p/n 782 72 10 22 mm 75 mm long p/n 782 72 20 Ball joint socket set 9 pcs p/n 782 71 00
Socket hexagonal "Impact" 3/4" � drive D1 D2 L 17 mm 30,6 44 50 p/n 796 01 70 19 mm 32,9 44 50 p/n 796 01 90 22 mm 37 44 50 p/n 796 02 20 24 mm 39,2 44 50 p/n 796 02 40 26 mm 41,3 44 50 p/n 796 02 60 27 mm 43 44 50 p/n 796 02 70 30 mm 47 44 53 p/n 796 03 00 32 mm 49,2 44 56 p/n 796 03 20 33 mm 50 44 56 p/n 796 03 30 34 mm 51,3 44 56 p/n 796 03 40 36 mm 53,5 44 56 p/n 796 03 60 38 mm 56,3 44 57 p/n 796 03 80 41 mm 61 44 57 p/n 796 04 10 42 mm 61,3 44 57 p/n 796 04 20 46 mm 67 44 60 p/n 796 04 60
Socket hexagonal 270 mm long "Impact" 1" � drive With continuous drilling, for extremely low-lying bolts. Ø outside length 27mm 45mm 270mm p/n 798 02 70 30mm 48mm 270 mm p/n 798 03 00 32mm 51mm 270 mm p/n 798 03 20 33mm 54mm 270 mm p/n 798 03 30 34mm 55 mm 270 mm p/n 798 03 40 36mm 56 mm 270 mm p/n 798 03 60
E profile socket "Impact" 1/2" � drive Socket E 10 x 38 mm long p/n 788 21 00 Socket E 12 x 38 mm long p/n 788 21 20 Socket E 12 x 80 mm long* p/n 788 61 20 Socket E 14 x 38 mm long p/n 788 21 40 Socket E 14 x 80 mm long* p/n 788 61 40 Socket E 16 x 38 mm long p/n 788 21 60 Socket E 18 x 38 mm long p/n 788 21 80 Socket E 20 x 38 mm long p/n 788 22 00 * Type : MB C / E class drive shaft screws
E profile socket extra long "Impact" 3/4" � drive x 110 mm long E profile socket E 18 p/n 606 28 18 E profile socket E 20 p/n 606 28 20 E profile socket E 22 p/n 606 28 22 E profile socket E 24 p/n 606 28 24
Hex bit socket "Impact" Application samples Type : MB brake disks / lining Audi, VW drive shaft central screw Hex bit socket 12mm x 61 x 1/2" � drive p/n 791 10 12 Hex bit socket 14mm x 61 x 1/2" � drive p/n 791 10 14 Hex bit socket 17mm x 61 x 1/2" � drive p/n 791 10 17 Hex bit socket 19mm x 61 x 1/2" � drive p/n 791 10 19 Hex bit socket 12mm x 76 x 3/4" � drive p/n 796 11 12 Hex bit socket 14mm x 76 x 3/4" � drive p/n 796 11 14 Hex bit socket 17mm x 76 x 3/4" � drive p/n 796 11 17 Hex bit socket 19mm x 76 x 3/4" � drive p/n 796 11 19
Socket extra long "Impact" 110 mm Special socket size 22mm. This set contains a 22mm socket as required for example on the Mercedes A class models. Apart from this special size the usual sizes of 17, 19 and 21mm are included in the set. Socket extra long "Impact" set 1/2" X-large p/n 994 16 40 in a plastic box
J 31
Stud puller model S For screwing in and out of studs and screws with or without threads.
Stud-Ø Lift S -Ø L � drive 2,5 mm 24 mm 65 mm 1/4" p/n 113 10 25 3,5 mm 24 mm 65 mm 1/4" p/n 113 10 35 4 mm 24 mm 65 mm 1/4" p/n 113 10 40 5 mm 24 mm 65 mm 3/8" p/n 113 10 50 5 mm 24 mm 65 mm 1/2" p/n 113 10 55 6 mm 24 mm 65 mm 1/2" p/n 113 10 60 7 mm 24 mm 65 mm 1/2" p/n 113 10 70 8 mm 24 mm 65 mm 1/2" p/n 113 10 80 9 mm 28 mm 75 mm 1/2" p/n 113 10 90 10 mm 28 mm 75 mm 1/2" p/n 113 11 00 10,5 mm 28 mm 75 mm 1/2" p/n 113 11 10 12 mm 28 mm 75 mm 1/2" p/n 113 11 20 14 mm 34 mm 75 mm 1/2" p/n 113 11 40 16 mm 34 mm 75 mm 1/2" p/n 113 11 60 18 mm 48 mm 100 mm 3/4" p/n 113 11 800 20 mm 48 mm 100 mm 3/4" p/n 113 12 000 22 mm 48 mm 100 mm 3/4" p/n 113 12 200 24 mm 48 mm 100 mm 3/4" p/n 113 12 400 27 mm 63 mm 125 mm 3/4" p/n 113 12 700 30 mm 63 mm 125 mm 3/4" p/n 113 13 000 Lift S 1 set 3 pcs in a plastic case p/n 113 00 10 (6 - 8 - 10 mm) Lift S 2 set 4 pcs in a plastic case p/n 113 00 20 (6 - 8 - 10 - 12 mm)
Screw extractor pins model UF With these extractor pins the front square is twisted 90° and the intermediate flanks are hollowed out so that no material is displaced when hitting them in and the screw does not block further. The 16 piece set also includes drill fitting drill sockets. These drill sockets are stepped so they can be used both for protruding and sunken screw remains. These special drill sockets are also separately available e.g. for set p/n 110 00 00. Screw extractor pins lift UF set 4 pcs size 1 - 4 p/n 114 00 0F Screw extractor set 16 pcs lift UF with special drill sockets and drills p/n 114 01 5F
J 32
Screw extractor model B Special screw extractor set made from special steel for removing torn off screws and pins from 5 - 16 mm or 3/16" - 5/8". Applicable up to a depth of 25 mm. No expanding of the hole and no damage to the thread. Mode of operation: Drill with drill socket, hammer in the extractor pin and screw out with the nut. Extractor pins Size for pin-Ø - l thread mm/" mm 1 M 5-M 7 3,2 (1/8") 60 p/n 110 30 10 2 M 8-M 10 4,8 ( 3/16") 70 p/n 110 30 20 3 M 12 6,4 (1/4") 78 p/n 110 30 30 4 M 14 8,0 (5/16") 83 p/n 110 30 40 5 M 16 8,7 (11/32") 94 p/n 110 30 50 Extractor nut Size drill-Ø for mm l for mm pin size screw mm 1 3,2 1 10 16 p/n 110 20 10 2 4,6 2 11 16 p/n 110 20 20 3 6,4 3 13 16 p/n 110 20 30 4 8,0 4 14 16 p/n 110 20 40 5 8,7 5 17 16 p/n 110 20 50 HSS drill Size Ø mm socket-Ø l mm 1 3,2~1/8" size 1, 2, 3, 4 65 p/n 110 10 10 2 4,6~3/16" size 5, 6, 7 86 p/n 110 10 20 3 6,4~1/4" size 8 101 p/n 110 10 30 4 8,0~5/16" size 9 117 p/n 110 10 40 5 8,7~11/32" size 10 125 p/n 110 10 50 Drill sockets Size outside Ø Inner Ø 1 7 1/8" p/n 110 40 10 2 8 1/8" p/n 110 40 20 3 9 1/8" p/n 110 40 30 4 10 1/8" p/n 110 40 40 5 11 3/16" p/n 110 40 50 6 12 1/l 6" p/n 110 40 60 7 13 1/l 6" p/n 110 40 70 8 14 1/4" p/n 110 40 80 9 15 5/16" p/n 110 40 90 10 17 11/32" p/n 110 41 00 Screw extractor set complete M 5 - M 16 p/n 110 00 00
Bolt Twister Size 2 – 10 32 mm lg., 3/8" drive Sockets made from high-strength special steel with self fixing, conical special profile. For the release of screws with damaged female hexagon, XZN and T profiles Size 2 for M5 Size 6 for M10 - M12 Size 3 for M6 Size 8 for M14 - M16 Size 4 for M8 Size 10 for M18 - M20 Bolt Twister 6 pcs on a rail p/n 731 56 00
J 33
Hex ballpoint t-handle key blade length grip length 2,0 100 mm 56 mm p/n 961 00 20 2,5 100mm 56 mm p/n 961 00 25 3,0 100 mm 56 mm p/n 961 00 30 4,0 153 mm 56 mm p/n 961 00 40 5,0 153 mm 78 mm p/n 961 00 50 6,0 153 mm 78 mm p/n 961 00 60 Hex ballpoint T-handle key set 6 pcs p/n 961 00 00
Impact driver set 1/2" □ and 5/16" hexagonal drive Robust, impact driver system. For the loosening (and tightening) of seized screws. Max impact approx. 120 Nm. Impact driver set 6 pcs p/n 523 50 00 in a steel box
Reduction adapter Acceptance of hexagon bits square hexagon length 1/4" 1/4" 25 mm p/n 792 80 10 3/8" 1/4" 31 mm p/n 793 80 10 3/8" 5/16" 31 mm p/n 793 80 20 1/2" 1/4" 38 mm p/n 794 80 10 1/2" 5/16" 38 mm p/n 794 80 20
Philips bits 1/4" hexagon drive Size 1 x 25 mm p/n 531 01 00 size 3 x 25 mm p/n 531 03 00 Size 2 x 25 mm p/n 531 02 00 size 4 x 32 mm p/n 531 04 00 Philips bit set 4 pcs p/n 531 20 00
Philips bits 5/16" hexagon drive Size 1 x 32 mm p/n 541 01 00 size 3 x 32 mm p/n 541 03 00 Size 2 x 32 mm p/n 541 02 00 size 4 x 32 mm p/n 541 04 00 Philips bit set 4 pcs p/n 541 20 00
Hex bits 1/4" hexagon drive 3 mm x 25 mm p/n 532 03 00 6 mm x 25 mm p/n 532 06 00 4 mm x 25 mm p/n 532 04 00 8 mm x 25 mm p/n 532 08 00 5 mm x 25 mm p/n 532 05 00 10 mm x 25 mm p/n 532 10 00 Hex bit set 6 pcs p/n 532 20 00
J 34
Pozidrive bits 1/4" hexagon drive
Size 1 x 25 mm p/n 535 01 00 size 3 x 25 mm p/n 535 03 00 Size 2 x 25 mm p/n 535 02 00 size 4 x 32 mm p/n 535 04 00
Pozidrive bits set 4 pcs p/n 535 20 00
Pozidrive bits 5/16" hexagon drive
Size 1 x 32 mm p/n 545 01 00 size 3 x 32 mm p/n 545 03 00 Size 2 x 32 mm p/n 545 02 00 size 4 x 32 mm p/n 545 04 00
Pozidrive bits set 4 pcs p/n 545 20 00
T profile bits 1/4" hexagon drive
T 6 x 25 mm p/n 534 00 60 T 20 x 25 mm p/n 534 02 00 T 7 x 25 mm p/n 534 00 70 T 25 x 25 mm p/n 534 02 50 T 8 x 25 mm p/n 534 00 80 T 27 x 25 mm p/n 534 02 70 T 9 x 25 mm p/n 534 00 90 T 30 x 25 mm p/n 534 03 00 T 10 x 25 mm p/n 534 01 00 T 40 x 25 mm p/n 534 04 00 T 15 x 25 mm p/n 534 01 50
T profile bits set 11 pcs p/n 534 30 50
T profile bits 5/16" hexagon drive
T 20 x 35 mm p/n 544 02 00 T 40 x 35 mm p/n 544 04 00 T 25 x 35 mm p/n 544 02 50 T 45 x 35 mm p/n 544 04 50 T 27 x 35 mm p/n 544 02 70 T 50 x 35 mm p/n 544 05 00 T 30 x 35 mm p/n 544 03 00 T 55 x 35 mm p/n 544 05 50
T profile bits set 8 pcs p/n 544 20 50
XZN bits 5/16" hexagon drive M 6 x 28 mm p/n 547 06 00 M 12 x 36 mm p/n 547 12 00 M 8 x 28 mm p/n 547 08 00 M 14 x 38 mm p/n 547 14 00
Ratchet ring spanner offset 135 mm long. Special offset reversible ratchet ring spanner. For the acceptance of all bits with 1/4" and 5/16" hexagon drive for work in hard to reach places (e.g. loudspeaker installation) Ratchet ring spanner offset p/n 703 57 00
J 35
Flexible grabber 450 mm long. Flexible gripping tool with spring for small articles up to 30mm diameter. Flexible grabber p/n 526 00 30
Telescope magnet 6 mm Ø, length: 140 till 590 mm . With holding clip. Telescope magnet p/n 526 01 00
Force pliers set VDE tested (German Association for Electrical, Electronic & Information Technologies) Side cutting pliers and combination pliers Equipped with high-quality " " pliers with ergonomically formed 2 components grips. Contents: • Force combination pliers 180 mm - American model - Optimum power transmission because of improved leverage - Cutting edges additionally induction hardened - For hard and soft wires - Tool steel, drop-forged, oil-hardened • Side cutter 160 mm - Induction hardened precision cutting edges - Wave cross section for long lasting sharpness, patented - For hard and soft wires - Optimum power transmission because of improved leverage - Special tool steel Force pliers set 2 pcs p/n 925 01 20 Double joint pliers set Pointed (straight/45°) and flat-nose pliers, approx. 300 mm long Special double joint pliers for hard to reach places, e.g. on MB commercial vehicles, with driving cab lifted to loosen electrical system plug at the engine and body. Because of the double joint the pliers need little room to open for seizing plugs, pins and the like (see picture), with Plexiglas pipe. Double joint pliers set 3 pcs p/n 127 03 000
Spark plug plug double joint release pliers 45° 6 and 12 mm round, 320 mm long Spark plug pliers with double joint for low-lying and with hard to reach spark plugs. Because of the double joint the pliers need little room to open for seizing. Type: e.g. MB R class V6 and V8 spark plug plugs Spark plug double joint release pliers 2 pcs p/n 604 02 700
J 36
Special flat-nose pliers Special flat-nose pliers long straight p/n 927 01 10 Special flat-nose pliers long S form p/n 927 01 30 Special flat-nose pliers long 45° form p/n 927 01 50 Special flat-nose pliers long 90° form p/n 927 01 90 Special flat-nose pliers set 4pcs long version p/n 927 00 00
Circlip pliers American special steel - for inner and outer circlips Size length axle Ø points points Ø 00 150 3-10 straight 0,96 mm p/n 122 40 00 01 145 3-10 45° 0,96 mm p/n 122 50 00 02 140 3-10 90° 0,96 mm p/n 122 60 00 * 10 150 7-25 straight 1,2 mm p/n 122 40 10 * 11 145 7-25 45° 1,2 mm p/n 122 50 10 * 12 140 7-25 90° 1,2 mm p/n 122 60 10 * 20 215 18-60 straight 1,8 mm p/n 122 40 20 * 21 210 18-60 45° 1,8 mm p/n 122 50 20 * 22 200 18-60 90° 1,8 mm p/n 122 60 20 30 245 40-100 straight 2,3 mm p/n 122 40 30 31 240 40-100 45° 2,3 mm p/n 122 50 30 32 230 40-100 90° 2,3 mm p/n 122 60 30 Circlip pliers set 6 pcs in a plastic case* p/n 122 42 00 Circlip pliers set 12 pcs in a plastic case p/n 122 45 00
Circlip pliers For inner and outer circlips. Circlip pliers set 11 pcs in a plastic case p/n 122 40 60
Multi-function two-arm puller Size 1 work range 13 mm - 36 mm Size 2 work range 24 mm - 47 mm The special design of the puller hooks and puller bridge offers the user a work range from 13 mm to 47 mm with only two pullers of small design. With the loosening of the two lateral hex screws and reversing the medium pressure spindle many possibilities are given to pull bearings, wiper arms, battery clamps and the likes. Two-arm puller with changeable bridge size 1 p/n 904 00 40 Two-arm puller with changeable bridge size 2 p/n 904 00 50 Two-arm puller set with changeable bridge size 1 + 2 p/n 904 00 45
J 37
Special three leg puller Working range 19 mm - 45 mm with screwable fixing sleeve This three leg puller has a very large work range and a substantial advantage for fixing with a screwable fixing collar which holds the puller legs in position. Universal ranges of application and an indispensable aid when taking the bearings off from the anchors in electric motors make this an ideal tool for electrical workshops, Bosch service centres and similar specialized enterprises. Three leg puller "micro puller" with fixing sleeve p/n 904 00 00
Two leg puller size 2 Span 50 mm/clamping depth 40 mm Smallest puller with self pressing legs. Easy pulling off of small work pieces such as terminal clamps and small bearings on electrical motors etc. Two leg puller size 2 p/n 104 00 10
Puller model GU With the shears effect the stress of the adjustable legs increases during the pulling procedure. The legs are milled claw-like and pointed for use on narrow gaps. Size span clamping depth 1 6 - 100 mm 85 mm p/n 104 55 10 2 10 x 140 mm 120 mm p/n 104 55 20 3 15 x 140 mm 155 mm p/n 104 55 30
Three leg puller Span 70 mm / clamping depth 65 mm. For terminal clamps, small gear wheels, ball bearing etc. Three leg puller p/n 104 70 00
J 38
Three leg puller Due to the clamping nut the pulling legs are fixed at the work piece and so slipping of the legs is prevented. Universally applicable e.g. for transmission, starter and generator bearings. Size 1 and 2 with impact hammer e.g. for the disassembly of wheel bearing hub caps. Slide hammer size 2 p/n 103 02 10 0,7 kg M10 inner thread Three leg puller with spindle Size 1 Ø 10 - 60 mm p/n 104 06 15 Size 2 Ø 15 - 70 mm p/n 104 06 25 Size 3 Ø 20 - 100 mm p/n 104 06 35 Three leg puller with slide hammer 700g Size 1S Ø 10 - 60 mm p/n 104 07 10 Size 2S Ø 15 - 70 mm p/n 104 07 20 Size 3S Ø 20 - 100 mm p/n 104 07 30
Puller model F Die forged two leg puller with clamp. The legs are pressed by the clamp behind the part which should be removed, thus slipping is prevented. Clamp is removable. Size span clamping depth 1 70 mm 94 mm p/n 104 30 10 2 100 mm 100 mm p/n 104 30 20 3 140 mm 150 mm p/n 104 30 30
Puller model G Height adjustable turning puller for the loosening or removal of concise fitting parts such as axle bearings, pinion, bearing rings etc. It is possible to use the puller in confined spaces due to the special thin jaws. The clamping collar prevents slipping of the jaws. Size span clamping depth 1 100 mm 170 mm p/n 104 50 10 2 150 mm 270 mm p/n 104 50 20 3 150 mm 330 mm p/n 104 50 30 4 150 mm 425 mm p/n 104 50 40
J 39
Puller model E Forged pullers, CV-steel with specially hardened spindle and ball. By reversing the legs this can be used as an internal or external puller.
Two leg puller model E 2
Size span clamping depth leg width 1 25 -.80 mm 100 mm 20 p/n 104 20 10 2 25 - 130 mm 100 mm 20 p/n 104 20 20 3 50 - 160 mm 150 mm 25 p/n 104 20 30 4 60 - 200 mm 150 mm 25 p/n 104 20 40 5 80 - 250 mm 200 mm 35 p/n 104 20 50 6 80 - 350 mm 200 mm 35 p/n 104 20 60 7 110 - 520 mm 200 mm 35 p/n 104 20 70 8 170 - 640 mm 225 mm 50 p/n 104 20 80
Three leg puller model E 3 1 25 - 80 mm 100 mm 20 p/n 104 21 60 2 25 - 130 mm 100 mm 20 p/n 104 21 70 3 25 - 160 mm 150 mm 25 p/n 104 21 80 4 25 - 200 mm 150 mm 25 p/n 104 21 90
Replacement legs ( 1 piece )
Size Span clamping depth leg width 1 100 mm size 1 + 2 20 p/n 104 24 10 2 150 mm size 3 + 4 25 p/n 104 24 20 3 200 mm size 5 - 7 35 p/n 104 24 30 4 225 mm size 8 50 p/n 104 24 40 5 200 mm size 1 + 2 20 p/n 104 25 10 6 250 mm size 1 + 2 20 p/n 104 25 15 7 220 mm size 3 + 4 25 p/n 104 25 17 12 300 mm size 3 + 4 25 p/n 104 25 20 13 300 mm size 5 + 7 35 p/n 104 25 30 23 400 mm size 5 + 7 35 p/n 104 26 30 33 500 mm size 5 + 7 35 p/n 104 27 30 14 300 mm size 8 50 p/n 104 25 40 24 400 mm size 8 50 p/n 104 26 40 34 500 mm size 8 50 p/n 104 27 40 Replacement legs without clamp for model E Size 1 20 mm wide for size 1 and 2 p/n 104 24 11 Size 2 25 mm wide for size 3 and 4 p/n 104 24 21 Size 3 35 mm wide for size 5, 6 and 7 p/n 104 24 31 Size 4 50 mm wide for size 8 p/n 104 24 41
J 40
Puller Krallex model F / S Two and three legs Span 25 - 130 mm Legs 150 / 200 / 250 mm long Jaw thickness 2,0 / 3,6 mm Outer and inner puller with slim legs particularly suitable for small spaces. As a result of the different leg lengths and different jaw forms a large area of application is possible. Type : Universal 1 x two leg bridge 25-130 mm p/n 104 22 20 1 x three leg bridge 25-130 mm p/n 104 88 80 1 x spindle 210 mm long p/n 104 23 20 1 x spindle with T-bar grip 250 mm long p/n 104 98 70 3 x leg size 1 100 mm long, with jaw F 2,0 p/n 104 88 91 3 x leg size 2 200 mm long, with jaw F 2,0 p/n 104 88 92 3 x leg size 3 250 mm long, with jaw F 2,0 p/n 104 88 93 3 x jaw Krallex 3,6 thick x 27 mm wide p/n 104 25 55 3 x jaw Krallex S 3,6 thick x 14 mm wide p/n 104 25 53 1 x bracket p/n 104 98 95 Puller Krallex model F / S two and three leg p/n 104 98 10 in a steel box
Puller Krallex model D Two and three legs Span 50 - 160 mm Legs 150 / 220 / 300 mm long Jaw thickness 5,0 mm A heavy duty version for various applications. Outer and inner pullers with slim jaws are particularly suitable for small spaces. Type : Universal Two leg bridge 50 - 160 mm (just two leg puller) p/n 104 22 30 Three leg bridge 50 - 160 mm (just three leg puller) p/n 104 88 84 Spindle 210 mm long p/n 104 23 30 Leg 150 mm long ( with jaw 5,0) p/n 104 88 71 Leg 220 mm long ( with jaw 5,0) p/n 104 88 72 Leg 300 mm long ( with jaw 5,0) p/n 104 88 73 Puller Krallex model D2 two legs p/n 104 98 40 with 6 legs (2 each) Puller Krallex model D3 three legs p/n 104 98 30 with 9 legs (3 each)
J 41
Krallex / Krallex
Puller model Krallex Particularly slim ending puller hooks give extra grip to the pullers in tight pulling applications.
Model Krallex F ( with extra slim legs ) Size Span
mm Clamping depth
mm Spindle
Thread x length mm Jaw
thickn. Jaw
width P/n
1 25 - 80 100 M14 x 1,5 x 130 17 2,0 27 104 89 40 2 25 - 130 100 M14 x 1,5 x 130 17 2,0 27 104 89 45
Model Krallex S ( with narrow legs ) Size Span
mm Clamping depth
mm Spindle
Thread x length mm Jaw
thickn. Jaw
width P/n
1 25 - 80 100 M14 x 1,5 x 130 17 3,6 14 104 89 80 2 25 - 130 100 M14 x 1,5 x 130 17 3,6 14 104 89 85
J 42
Puller Krallex model F Two and three legs Span 25 - 100 mm Legs 100 mm lg. Jaw thickness 2,0 / 3,6 mm With quick-action clamping nut and particularly slim Krallex F puller jaws. The puller jaws permit the employment also in tight pulling situations. Due to the quick-action clamping nut the change from the 2-arm to the 3-arm bridge is rapidly accomplished and the setting of the puller is substantially simplified. Contents: Bridge 3 legs Bridge 2 legs Spindle 3 x legs with quick-action clamping nut Puller Krallex model F two and three legs p/n 104 99 50 in a plastic case
Hydraulic pull system Thrust force 12 t. - Fat hydraulic building block principle suitable for
2 -and 3-legged pullers. Special leg construction (the greater the pressure, the more stress on the legs). Contents: 1 x hydraulic spindle 12 t with thrust piece p/n 104 16 50 1 x 2 leg bridge p/n 104 16 20 1 x 3 leg bridge p/n 104 16 30 3 x leg p/n 104 17 10 (span 50 - 100 mm, clamping depth 100 mm) 3 x leg p/n 104 17 20 (span 75 - 150 mm, clamping depth 150 mm) 3 x leg p/n 104 17 30 (span 100 - 200 mm, clamping depth 200 mm) 1 x spindle extension 50 mm long p/n 104 18 60 1 x spindle extension 100 mm long p/n 104 18 70 1 x spindle extension 150 mm long p/n 104 18 80 Hydraulic pull system 15 pcs p/n 104 15 00 Accessories: legs p/n 104 18 30 (span 75 - 150 mm, clamping depth 250 mm) legs p/n 104 18 40 (span 130 - 250 mm, clamping depth 250 mm)
Multi leg hub puller model P1 - P3 Strong version with pitch diameter Ø up to 225 mm and axially mobile threaded bush with annular groove for the admission of 2 to 5 adjustable pulling legs. For the safe removal of wheel hubs. Type: passenger car universal Multi leg hub puller model P 1 3 legs p/n 105 60 10 Multi leg hub puller model P 2 4 legs p/n 105 60 20 Multi leg hub puller model P 3 5 legs p/n 105 60 30
J 43
Extractor model NA Size Span Length Fitting to min-max extr. rod extractor 2 65-115 mm 150 mm NT 1+2 p/n 105 20 20 3 80-210 mm 210 mm NT3 p/n 105 20 30 4 100-295 mm 315 mm NT4 p/n 105 20 40 5 150-350 mm 305 mm NT5 p/n 105 20 50
Separator NT
Robust separator with sharp, tapered edges.
Fitting to Size Span extractor 1 10 - 60 mm NA 2 p/n 105 10 10 2 15 - 75 mm NA 2 p/n 105 10 20 3 35 -115 mm NA 3 p/n 105 10 30 4 40 -150 mm NA 4 p/n 105 10 40 5 48 -220 mm NA 5 p/n 105 10 50
Extensions for extractor model NA Fitting to Size Length M extractor NV 1 100 mm M12 NA 2 p/n 105 30 10 NV 2 100 mm M 16 NA 3 p/n 105 30 20 NV 3 100 mm M 20x1,5 NA 4 + 5 p/n 105 30 30
Internal extractor sets Compact sets with large clamping range. Split collets made from one source (particularly wear resistant). With even spreading for safe and careful extraction. These are suitable for ball bearings, - outer rings, sockets and seals. Set size 1 10 - 37 mm holes p/n 104 97 01 5 collets size 1A, 2A, 3A, 4A, 5A counter stay size 1 and slide hammer 103 02 00 Set size 2 10 - 45 mm holes p/n 104 97 02 6 collets size 1A, 2A, 3A, 4A, 5A , 6A and 1 counter stay size 1 Set size 5 15 - 75 mm holes p/n 104 97 10 4 collets size 2A, 3A, E3, E7 counter stay size 2, thread adapter
J 44
Collets Split collets from one source (particularly wear resistant). With even spreading for safe and careful extraction. They are suitable for ball bearings, - outer rings, sockets and seals. Size Hole Ø Thread mm 0A 5-7 M10 p/n 104 96 01 0B 7-9 M10 p/n 104 96 02 0C 9-12 M10 p/n 104 96 03 1A 10-13 M10 p/n 104 96 11 1B 13-17 M10 p/n 104 96 12 2A 14-19 M10 p/n 104 96 21 2B 16-21 M10 p/n 104 96 22 2C 18-23 M10 p/n 104 96 23 3A 20-25 M10 p/n 104 96 31 4A 25-30 M10 p/n 104 96 41 5A 30-37 M10 p/n 104 96 51 5B 35-42 M10 p/n 104 96 52 6A 38-45 M10 p/n 104 96 61 E3 25-40 M10 p/n 104 96 30 E 7 40-75 R 3/8" p/n 104 96 96 E 8 70-115 R 3/8" p/n 104 96 98
counter stay For Adapter Spindle Size extractor thread thread Reach 1 0A - 6A M 10 M 16x1,5 35- 75 mm 2 E7 + E8 R 3/8" M 24x1,5 60-130 mm 3 E7 + E8 R 3/8" M 24x1,5 60-210 mm 4 E7 + E8 R 3/8" R1/2" 14G 60-210 mm Counter stay size 1 p/n 105 01 10 Counter stay size 2 p/n 105 01 20 Counter stay size 4 p/n 105 01 40
Pressure piece set ALU Versatile pressure piece set made from aluminium. The installation forces are transferred evenly and carefully so that damage to ball bearings, sockets, shaft seals etc is avoided. For use with a rubber or plastic hammer Contents: 1 handle 120 mm long with retaining screw 9 pressure pieces with outside Ø: 40/ 44/ 50/ 59/ 63/ 65/ 72/ 76/ 81 Pressure piece set ALU 10 pcs p/n 614 45 30
J 45
Vice soft jaws Width 140 mm Magnetic auxiliary jaws can be put on the vice jaws when needed. So it is possible to work on very sensitive parts. 1 pair aluminium soft jaws 1 pair aluminium prism soft jaws 1 pair aluminium soft jaws with rubber coating 1 pair aluminium soft jaws with fibber coating Vice soft jaws 4 pcs p/n 701 00 10
Vice soft jaws set model 2 120 mm long with retaining magnet.
The back magnets fix the protection jaws to the vice jaws. The special formed plastic jaws adapt to the form of the part and give it safe hold without damage. So very sensitive parts can be worked on. With special jaws for the disassembly/assembly of shock struts it is possible to clamp the struts without damage at an angle of 45°. 1 pair plastic soft jaws p/n 946 17 60 1 pair aluminium shock strut soft jaws p/n 946 12 00 Vice soft jaws set model 2, 2 pcs p/n 701 00 20 in a pouch
Lever set - commercial vehicles Lever set, developed for the special requirements of the commercial vehicle workshop. Ergonomic plastic handle, laid out for use with 2 hands. With a solid impact head for the highest demands. Continuous square special steel blade 16 x 16 mm, hardened and tempered, can be reground. Application e.g.: Leaf spring bolt eye Annul the rotary shaft seals in the wheel hub (special size 3) To install wheels onto a vehicle (special size 2) To examine ball joints and steering cross rods and steering side rods To check bushes for play Size 1 610 mm x 90° p/n 119 10 01 Size 2 910 mm x 45° p/n 119 10 02 Size 3 610 mm x 60° p/n 119 10 03 Size 4 910 mm x straight p/n 119 10 04 Lever set 4 pcs p/n 119 11 00
J 46
Hydraulic nut splitter Suitably for nuts 7 – 22mm , max load 5 t
For removing de-threaded nuts
- Small effort necessarily - Slim build, so easy to work on hard to reach places - In addition the jaw is inductively hardened Hydraulic nut splitter p/n 118 50 00 Replacement jaw p/n 118 50 10 Anvil p/n 118 50 20
Double action pumps extraction and pressure Volumes 125ml and 250ml Robust hand extraction pumps with double stroke. The pumps pump fluid with each movement; therefore there are no “no-load operation “pump strokes. The aluminium housing and plastic parts from which the pumps are manufactured, are suitable for liquids such as diesels, heating oil, engine oil, brake fluid, water and different coolants. ATTENTION these pumps are not to be used for petrol, acids and caustic solutions! Double-acting pump universal 125 ml volume aluminium housing with plastic hoses p/n 80125125 Double-acting pump universal 250 ml volume aluminium housing with plastic hoses p/n 80125250
Impact gun 3/8" butterfly Weight 950 g., about 150 mm long. 8 adjust steps, idling 9000 U/min, Torque max. 102 Nm Swivelling compressed air connector.
Small, handy impact gun with practical operating jack for the direction of rotation choice. With its compact and light construction it is particularly suitably for work in the engine compartment e.g. for valve cover disassembly.
Impact gun 3/8" butterfly p/n 923 53 00
J 47
Impact gun Silent Power Drive square 1/2" Idling speed 7.000 rpm Fastening torque 880 Nm Release torque 990 Nm Weight 1,95 kg Air pressure 6,3 bar Air inlet:. 1/4" Acoustic pressure 85 dB/A A high-quality impact gun with every conceivable advantage for the modern workshop. The plastic housing, exhaust air downward silent power and huge torque distinguish this tool from others. With a very well balanced weight of 1.95 kg make this easy to use 1/2" Impact gun with 3 different speeds and a release of 990 Nm suitable for the highest requirements. With a double hammer blow action. Impact gun Silent Power 1/2" Silent Power p/n 923 52 00S
Impact gun Drive square 3/4" Spindle length 1" Idling speed 4.200 rpm Output 1.345 nm Weight 5,2 kg Air pressure 6,2 bar Air inlet:. 3/8" High performance, robust 3/4" Impact gun with excellent weight per horsepower ratio. 3 fastening and 3 release torques ensure a broad
field of application. Exit air discharge is through the grasp downward. Impact gun 1 p/n 923 55 00
Impact gun "low noise" New generation A 1/2" Impact gun “GOLD" with ergonomic plastic housing making it easy to operate, it is the “low noise" version. Exhaust air downward, 3 performance levels with a maximum
torque of 660 Nm. Impact gun "GOLD" low noise A 1/2" 660 NM p/n 923 52 50S
Impact gun "Silent Power" A 1 A 1" impact gun with a spindle length of 8". Unique “Silent Power" and an incredible maximum torque of 2430 Nm – so it is suitable for trucks, construction equipment etc. Impact gun "Silent Power" A 1" 2340 NM p/n 923 56 00S
J 48
Compressed air rivet gun for rivets up to 6,4 mm, in a case A pneumatically operated rivet gun for rivets up to 6.4 mm Practical version in a plastic case Compressed air rivet gun. p/n 924 76 00 In a plastic case
Compressed air chisel hammer For Hex bits. Includes a special insert for jolting This standard compressed air device has been re-designed to become a helpful special tool. In connection with the production of a special chisel with a hexagonal drive, which has a V-type recess instead of a chisel point - and a commercial pneumatic hammer, these tools can be used to help during the disassembly of seized injectors. With our superior range of injector disassembly tools such as the special sets for MB, Renault, Fiat or PSA the air chisel can be used to directly jolt the seized injector. Chisel hammer set model S with 1 piece chisel insert for jolting seized injectors p/n 802 20 00 Special chisel hammer insert S8 for jolting seized injectors p/n 820 20 10
Pneumatic rivet drilling kit With replaceable inserts and drills The technologies in the use and processing of new materials and the connection techniques in the auto body bring new challenges for the repair, disassembly and assembly of steel sheet pieces. These include spot-welds, welds, adhesives, solder and of course rivets. In order to be able to drill out optimally and centrally the very hard and varying diameter large rivets during separation of sheet metals, this special pneumatic rivet drill set contains 3 replaceable centring inserts and 2 different large " RIVET –DRILL-BIT" drills, which are exactly adapted to the standard commercially used rivets Pneumatic rivet drilling kit p/n 825 05 45
J 49
Pneumatic one hand disc grinder This unique hand disc grinder functions in connection with fibre corundum grinding disks. The newly conceived 5" hole support disk permits a good view of the work surface and gives special air cooling of the work area. Further advantages are speed regulation, lightness and an ergonomically formed handle for easy use. Pneumatic one hand disc grinder "BELLA-VISTA" for 5 holes fibre corundum grinding disks. p/n 804 38 00
Pneumatic corner-grinder Idling speed: 15.000 U/min Output: 0,85 PS/0,63 kW Total length: 350mm Height: 65mm Weight: 1,1 kg Air pressure: 6,3 bar Air inlet: ¼“ The design of this corner cutter makes possible optimal work in hard to reach places on motor vehicles and locksmith's works. In particular corroded and idle turning screw connections can be cut through simply and easily for example: connecting rod and anti-roll bars, tie rods and tie rod ends as well as carrying joints (Ford, Opel or BMW). Exhaust screw connections can be separated just as easily, also wheel arches and the screw connections of many rear axle bushes which are hard to reach (in the Golf III the brake pressure regulator must be dismantled to do this). Pneumatic corner cutter p/n 804 45 00
Cleaning pistol "TORNADOR " This simple air gun with “Tornador" - funnel attachment can be filled with any conventional cleaning agent and connected to compressed air. For hard to reach places such as radio consoles, lattices of risers, centre consoles, roof skies, seats and carpets simply everything in the vehicle can be cleaned without scrubbing. Simply hold the pistol with the funnel directly over the place to be cleaned and spray until the dirt has disappeared. Cleaning pistol "TORNADOR" p/n 949 52 50
J 50
O-ring assortment 419 pcs A 419 piece O-ring set. The set covers O-rings of 3.0 mm inside diameters up to 50.0 mm. The rings have different strengths from 1.5 mm to 3.5 mm and are contained in different numbers of items ranging from 10 to 20 in the assortment O-ring assortment 419 pcs metric p/n 913 43 60 O-ring assortment 419 pcs inch p/n 913 43 70
Grooved nut key UNI adjustable With 4 pair replaceable points This universal grooved nut key is universal applicable because of its adjustable range of 20mm to 90mm and its 4 pairs of screwed ends with diameters 2.5/4.0 mm 3.0/5.0 mm 6.0/8.0 mm and 7.0/11.0 mm. Predominantly for use with the repair of screw connections which have drillings, grooves or slots for stopping, releasing or tightening Grooved nut key UNI p/n 940 13 90
Socket wrench set „Surface Drive“ 1/4" - 3/8" - 1/2" This set contains ¼”, 3/8” and ½” drives easily accessible in one handy carry case. Contained in the set are tools in profiles E-Torx, TX, hex, Philips and slotted heads. The ratchets are fine toothed equipped with ergonomic handles and a holding device. Socket wrench set „Surface Drive“150 pcs p/n 740 01 60
L 01
Spot weld drill 3 fluted with multilayer alloy Solid tungsten carbide drill STC 8 x 44mm for maximum rigidity sheet metals (Usibor), which are used for example in the cross framework and side members, but partially in the door sills or A and B-columns in models from Daimler/Chrysler, Porsche, VW, Audi, BMW, Volvo, Peugeot and many others. For these extremely hard and tough sheet metals this high-tech drill has been specially developed as 3 fluted and has a completely new “multilayer” coating, with all the advantages of the conventional TiN, TiAIN + TiCN alloys combined. Replacement miller for SPEEDY 8,0 x 44 mm solid tungsten carbide, 3 fluted for „Spitznagel Drill“ p/n 270 61 05 Replacement miller for SPEEDY 8,0 x 44 mm solid tungsten carbide, 3 fluted for “Vario-Drill” p/n 270 61 10
Stepped drill " Gold " Long service life because of the titanium nitrite (Tin) coating. The hole diameter is readable by the laser scale in the slot. For the number of revolutions required approximate values for steel/CrNi (VA) are printed in a table in the lid of the steel sheet cartridge. With flat spot for burr free drilling of sheet metals, pipes and profiles up to 4 mm material thickness. Stepped drill size 1 Ø4 - 12 mm, 1 mm ascending p/n 280 24 00 Stepped drill size 1a Ø4 - 20 mm, 2 mm ascending p/n 280 24 50 Stepped drill size 2 Ø 6 - 30 mm, 2 mm ascending p/n 280 25 00 Stepped drill " Gold ", 3 pcs. in steel box p/n 280 28 50 Stepped drill size 3 Ø 9 - 36 mm, 3 mm ascending p/n 280 26 00 Stepped drill size 4 Ø 30 - 40 mm, 1 mm ascending p/n 280 30 40
Hole cutter Conical special sheet metal drills from HSS for burr-free drilling and reaming. (Steel sheets, stainless steel, V2A, non-ferrous metals, plastics, wood). Also available a special machine cutting paste ZSW for the protection and preservation of the drills performance.
Material: Non-ferrous Steel high-grade
steel Plastics
ST 14 / 37 stainless
steel V2
Material thickness 0,1-5 mm 0,1-3 mm 0,1-1,5 mm - 10 mm Size Ø / mm Shank-Ø mm rpm rpm rpm rpm p/n
The indicated rpm were determined with test drillings in a controlled
environment.
They serve only as a non-committal indication of performance.
L 02
Hand tap set 1 M 3 - M 12 DIN 352 HSS Contents: 7 sets of heavy duty hand taps, consisting of 1 pilot a middle and a finishing tap each. Hand tap set 1 in a steel box p/n 230 00 10
Tap and Die set 4 Contents: 7 sets of heavy duty hand taps, consisting of 1 pilot a middle and a finishing tap each, DIN 352, 7 HSS Dies M 3-M12 in equal height, outside diameter 25 x 9 mm. Also: 1 die stock, 1 tap wrench 1 screwdriver Tap and die set 4 p/n 230 00 40
Tap extensions Hardened universal extensions with inside and outside square as per DIN 10 for hand taps and reamers.
HSS-hand taps HSS heavy duty hand taps (high abrasion resistance) for high cutting velocities, with relief ground profile and precision thread. HSS-hand tap metric DIN 352 3 piece sets
Thread-Ø P/N
Thread-Ø Speed. / mm P/N. M 8 x 1 232 80 80
M1 0,25 230 71 00 M 9 x 1 232 80 90
M1,1 0,25 230 71 10 M10 x 1 232 81 00 M1,2 0,25 230 71 20 M 11 x 1 232 81 10 M1,4 0,3 230 71 40 M 12 x 1 232 81 20
M1,6 0,35 230 71 60 M 13 x 1 232 81 30 M1,7 0,35 230 71 70 M 14 x 1 232 81 40
M1,8 0,35 230 71 80 M 15 x 1 232 81 50 M2 0,4 230 72 00 M 16x 1 232 81 60
M2,6 0,45 230 72 60 M 24 x l 232 82 40 M3 0,5 230 73 00 M 25 x 1 232 82 50
M3,5 0,6 230 73 50 M 26 x 1 232 82 60 M4 0,7 230 74 00 M 27 x 1 232 82 70 M4,5 0,75 230 74 50 M 28 x 1 232 82 80
M5 0,8 230 75 00 M 30 x 1 232 83 00 M5,5 0,9 230 75 50 M 10 x 1,25 232 91 00
M6 1 230 76 00 M 11 x 1,25 232 91 10 M7 1 230 77 00 M 12 x 1,25 232 91 20 M8 1,25 230 78 00 M 14 x 1,25 232 91 40
M9 1,25 230 79 00 M 16 x 1,25 232 91 60 M10 1.5 230 81 00 M 18 x 1,25 232 91 80
M11 1,5 230 81 10 M 20 x 1,25 232 92 00 M12 1.75 230 81 20 M 12 x 1,5 233 01 20 M14 2 230 81 40 M 13 x 1,5 233 01 30
M16 2 230 81 60 M 14 x 1,5 233 01 40 M18 2,5 230 81 80 M 15 x 1,5 233 01 50
M20 2.5 230 82 00 M 16 x 1,5 233 01 60 M22 2,5 230 82 20 M 18 x 1,5 233 01 80
M24 3 230 82 40 M 20 x 1,5 233 02 00 M27 3 230 82 70 M 21 x 1,5 233 02 10 M30 3,5 230 83 00 M 22 x 1,5 233 02 20
M33 3,5 230 83 30 M 23 x 1,5 233 02 30 M36 4 230 83 60 M 24 x 1,5 233 02 40
M39 4 230 83 90 M 25 x 1,5 233 02 50 M42 4,5 230 84 20 M 26 x 1,5 233 02 60 M45 4,5 230 84 50 M 27 x 1,5 233 02 70
M48 5 230 84 80 M 28 x 1,5 233 02 80 M52 5 230 85 20 M 29 x 1.5 233 02 90
M 30 x 1,5 233 03 00 M 32 x 1,5 233 03 20
M 33 x 1,5 233 03 30 HSS-hand tap metric fine DIN 2181
2 piece sets M 34 x 1,5 233 03 40
M 35 x 1,5 233 03 50
Thread-Ø P/N M 36 x 1,5 233 03 60 M 3 x 0,35 232 50 30 M 38 x 1,5 233 03 80
M 4 x 0,35 232 50 40 M 39 x 1,5 233 03 90 M 4 x 0,5 232 60 40 M 40 x 1,5 233 04 00 M 5 x 0,5 232 60 50 M 42 x 1,5 233 04 20
M 6 x 0,5 232 60 60 M 45 x 1,5 233 04 50 M 8 x 0,5 232 60 80 M 48 x 1,5 233 04 80
M 10 x 0,5 232 61 00 M 50 x 1,5 233 05 00 M 6 x 0,75 232 70 60 M 52 x 1,5 233 05 20 M 7 x 0,75 232 70 70
M 8 x 0,75 232 70 80 M 9 x 0,75 232 70 90
M 1 0 x 0,75 232 71 00 M 12 x 0,75 232 71 20 M 14 x 0,75 232 71 40
L 03
HSS hand taps metric fine DIN 2181 2 pcs sets
Hand taps HSS DIN 351 American coarse thread – sets 3 pcs.
Thread-Ø P/N Thread-Ø threads per inch P/N
M 18 x 2 233 11 80 NC 1/4 20 234 30 10
M 20 x 2 233 12 00 NC 5/16 18 234 30 20
M 22 x 2 233 12 20 NC 3/8 16 234 30 30
M 24 x 2 233 12 40 NC 7/16 14 234 30 40
M 26 x 2 233 12 60 NC 1/2 13 234 30 50
M 27 x 2 233 12 70 NC 9/16 12 234 30 60
M 28 x 2 233 12 80 NC 5/8 11 234 30 70
M 30 x 2 233 13 00 NC 3/4 10 234 30 80
M 33 x 2 233 13 30 NC 7/8 9 234 30 90
M 36 x 2 233 13 60 NC 1 8 234 31 00
M 39 x 2 233 13 90 NC 1 1/8 7 234 31 10
M 40 x 2 233 14 00 NC1 1/4 7 234 31 20
M 42 x 2 233 14 20 NC 1 3/8 6 234 31 30
M 45 x 2 233 14 50 NC1 1/2 6 234 31 40
M 48 x 2 233 14 80 M 50 x 2 233 15 00 M 52 x 2 233 15 20
M 30 x 3 233 23 00
HSS hand taps DIN 351 American fine pitch thread NF – sets 3 pcs.
M 36 x 3 233 23 60 Thread-Ø threads per inch P/N
M 39 x 3 233 23 90 NF 1/4 28 235 30 10
M 40 x 3 233 24 00 NF 5/16 24 235 30 20
M 42 x 3 233 24 20 NF 3/8 24 235 30 30
M 45 x 3 233 24 50 NF 7/16 20 235 30 40
M 48 x 3 233 24 80 NF 1/2 20 235 30 50
M 50 x 3 233 25 00 NF 9/16 18 235 30 60
M 52 x 3 233 25 20 NF 5/8 18 235 30 70
NF 3/4 16 235 30 80
NF 7/8 14 235 30 90
NF 1 12 235 31 00
NF 1 14 235 31 10
NF 1 1/8 12 235 31 20
NF 1 1/4 12 235 31 30
NF 1 3/8 12 235 31 40
NF 1 1/2 12 235 31 50
Machine tap DIN 352 HSS short machine taps
for metric thread or metric ISO thread DIN 13 Standard
version AZ version with
interrupted thread Standard
version AZ version with
interrupted thread
Thread-Ø P/N P/N Thread-Ø P/N P/N M 3 242 30 30 242 00 30 M 12 242 31 20 242 01 20 M 4 242 30 40 242 00 40 M 14 242 31 40 242 01 40
M 5 242 30 50 242 00 50 M 16 242 31 60 242 01 60 M 6 242 30 60 242 00 60 M 18 242 31 80 242 01 80
M 7 242 30 70 242 00 70 M 20 242 32 00 242 02 00 M 8 242 30 80 242 00 80 M 22 242 32 20 242 02 20
M 10 242 31 00 242 01 00 M 24 242 32 40 242 02 40
L 04
L 05
Tap wrench Adjustable tap wrench with hardened steel jaws as per DIN 1814 with unscrewable arms.
���� size Metric P/N ���� size Metric P/N
0 M 1 - 8 267 50 00 4 M 10 – 27 267 54 00 1 M 1- 10 267 51 00 5 M 14 – 33 267 55 00
1 ½ M 3 – 12 267 51 50 6 M 18 – 42 267 56 00 2 M 4 – 22 267 52 00 7 M 27 – 52 267 57 00
3 M 5 -20 267 53 00
Tap ball wrench With unscrewable arms and fixed square holes.
Size Square Metric /fine P/N
0 2,1 - 2,7- 3.0 - 3,4 M 1 - 4,5 266 00 00
1 3.0 - 3,4 - 4,3 - 4,9 M 3,5 - 8 266 00 10
2 3,4 - 4,3 - 4,9 - 5,5 M 4 - 10 266 00 20
3 4,9 - 5,5 - 6,2 - 7.0 M 5 - 12 266 00 30
4 5,5 - 6,2 - 7.0 - 9.0 M 9 - 16 266 00 40
5 7.0 – 9.0 - 11 - 12 M 12 - 20 266 00 50
6 11 - 12 -14,5 – 6.0 M 18 - 27 266 00 60
Tap tool holder. For the admission of thread taps with ratchet and hardened steel chuck.
Size Metric Length P/N
1 M 3 - M 10 80 mm 268 00 10
2 M 5 - M 12 97 mm 268 00 20
3 M 3 - M 10 250 mm 268 10 10
4 M 5 - M 12 300 mm 268 10 20
Die stock Die stock as per DIN 225 for the direct admission of round dies, DIN 223
Size Inside-Ø x height mm
Metric P/N
1 16 x 5 M 1 - 2,6 265 00 10
2 20 x 5 M 3 – 4 265 00 20
3 20 x 7 M 4,5 - 6 265 00 30
4 25 x 9 M 7 - 9 265 00 40
5 30 x 11 M 10 - 11 265 00 50
6 38 x 10 M 12 - 14 265 00 60
7 38 x 14 M 12 - 14 265 00 70
8 45 x 14 M 15 - 20 265 00 80
9 45 x 18 M 16 - 20 265 00 90
10 55 x 16 M 22 - 24 265 01 00
11 55 x 22 M 22 - 24 265 01 10
12 65 x 18 M 25 - 36 265 01 20
13 65 x 25 M 27 - 36 265 01 30
14 75 x 20 M 38 - 42 265 01 40
15 75 x 30 M 39 - 42 265 01 50
16 90 x 22 M 45 - 52 265 01 60
L 06
Die stock. For round dies, DIN 223. To be used in the tightest areas. Manipulation by ratchet and socket or by the enclosed box spanner (female hexagon 24mm and external hexagon 30mm)
M admission external hexagon
female hexagon
P/N
3 - 6* Ø 20 24 265 50 10
7 - 8* Ø 25 24 265 50 20
9 - 10* Ø 30 24 265 50 30
11 - 14* Ø 38 41 30 265 50 40
18 - 20 Ø 45 41 30 265 50 50
22 - 24 Ø 55 41 30 265 50 60
Grip for die stock p/n 265 55 00 Die stock set 7 pcs. p/n 265 60 00 Die stock set 5 pcs. * p/n 265 65 00
Thread repair and cleaning set M12x1,25 / M12x1,50 / M 14x1,50
An ideal set arrangement for cleaning and re-cutting the threads of wheel hubs, wheel bolts, stay bolts and wheel nuts. Salt, corrosion, rust, contamination or diagonal setting risks the danger of damage to the threads and can produce the wrong torques when tightening. With this universal cleaning and repair set these problems can be repaired and/or avoided.
Thread repair and cleaning set p/n 232 20 10
Thread inch-Ø threads per inch
Outside Ø mm
Height mm
P/N
NC 1/4 20 20 7 2520010
NC 5/16 18 25 9 2520020
NC 3/8 16 30 11 2520030
NC 7/16 14 30 11 2520040
NC 1/2 13 38 14 2520050
NC 9/16 12 38 14 2520060
NC 5/8 11 45 18 2520070
NC 3/4 10 45 18 2520080
NC 7/8 9 55 22 2520090
NC 1 8 55 22 2520100
NC 1 1/8 7 65 25 2520110
NC 1 1/4 7 65 25 2520120
NC 1 3/8 6 65 25 2520130
NC 1 1/2 6 75 30 2520140
HSS dies round DIN 223 for metric thread or metric
ISO Fine thread DIN 13
HSS-Dies Hexagon DIN 382
Thread Pitch mm Outside
Ø P/N MM P/N
M1 0.25 16 2500100 - -
M 1,1 025 16 2500110 - -
M 1,2 0.25 16 2500120 - -
M1,4 0,3 16 2500140 - -
M1.6 0.35 16 2500160 - -
M1.7 035 16 2500170 - -
M1,8 0.35 16 2500180 - -
M2 0,4 16 2500200 - -
M2,2 0,45 16 2500220 - -
M2.3 0.4 16 2500230 - -
M2,5 0.45 16 2500250 - -
M2,6 0.45 16 2500260 - -
M3 0,5 20 2500300 19 mm 2600300
M3,5 0.6 20 2500350 19 mm 2600350
M4 0,7 20 2500400 19 mm 2600400
M4,5 0.75 20 2500450 19 mm 2600450
M5 0,8 20 2500500 19 mm 2600500
M5,5 0,9 20 2500550 19 mm 2600550
M6 1 20 2500600 19 mm 2600600
M7 1 25 2500700 22 mm 2600700
M8 1.25 25 2500800 22 mm 2600800
M9 1.25 25 2500900 22 mm 2600900
M10 1,5 30 2501000 27 mm 2601000
M11 1,5 30 2501100 27 mm 2601100
M12 1,75 38 2501200 36 mm 2601200
M14 2 38 2501400 36 mm 2601400
M16 2 45 2501600 41 mm 2601600
M18 2,5 45 2501800 41 mm 2601800
M20 2,5 45 2502000 41 mm 2602000
M22 2,5 55 2502200 50 mm 2602200
M24 3 55 2502400 50 mm 2602400
M27 3 65 2502700 60 mm 2602700
M30 3,5 65 2503000 60 mm 2603000
M33 3,5 65 2503300 60 mm 2603300
M 36 4 65 2503600 60 mm 2603600
M 39 4 75 2503900 70 mm 2603900
M 42 4,5 75 2504200 70 mm 2604200
M 45 4,5 90 2504500 85 mm 2604500
M 48 5 90 2504800 85 mm 2604800
M 52 5 90 2505200 85 mm 2605200
HSS dies round for American coarse thread NC
HSS dies round for American fine pitch thread NF
HSS dies round DIN 223 for metric thread or
metric ISO fine thread DIN 13
HSS-Dies Hexagon DIN 382
Thread Outside Ø Height mm P/N MM P/N
M 3 x 0,5 20 5 2510030 19 mm 2610030
M 4 x 0,35 20 5 2510040 19 mm 2610040
M 4 x 0,5 20 5 2511040 19 mm 2611040
M 5 x 0,5 20 7 2511050 19mm 2611050
M 6 x 0,5 20 7 2511060 -
M 8 x 0,5 25 9 2511080
M 10 x 0,5 30 11 2511100 -
M 6 x 0,75 20 7 2512060 19 mm 2611060
M 7 x 0,75 25 9 2512070 -
M 8 x 0,75 25 9 2512080 22 mm 2611080
M 9 x 0,75 25 9 2512090 - -
M 10 x 0,75 30 11 2512100 - -
M 12 x 0,75 38 10 2512120 - -
M 14 x 0,75 38 10 2512140 - -
M 8 x l 25 9 2513080 22 mm 2612080
M 9 x 1 25 9 2513090 22 mm 2612090
M 10 x 1 30 11 2513100 27 mm 2612100
M 11 x l 30 11 2513110 27 mm 2612110
M 12 x 1 38 10 2513120 36 mm 2612120
M 13 x 1 38 10 2513130 - -
M 14 x 1 38 10 2513140 - -
M 15x 1 45 14 2513150 - -
M 16 x 1 45 14 2513160 - -
M 18 x 1 45 14 2513180 - -
M 20 x 1 45 14 2513200 - -
M 22 x 1 55 16 2513220 - -
M 24x1 55 16 2513240 - -
M 25x 1 65 18 2513250 - -
M 26x 1 65 18 2513260 - -
M 27 x 1 65 18 2513270 - -
M 28 x 1 65 18 2513280 - -
M 30 x 1 65 18 2513300 - -
M 10 x 1,25 30 11 2514100 - -
M 11 x 1,25 30 11 2514110 - -
M 12 x 1,25 38 10 2514120 - -
M 14 x 1,25 38 10 2514140 - -
M 16 x 1,25 45 14 2514160 - -
M 18 x 1,25 45 14 2514180 - -
M 20 x 1,25 45 14 2514200 - -
M 8 x 1,5 38 10 2515080
M 12 x 1,5 38 10 2515120 36 mm 2613120
M 13 x 1,5 38 10 2515130 -
M 14 x 1,5 38 10 2515140 36 mm 2613140
M 1 5 x 1,5 45 14 2515150 -
M 16 x 1,5 45 14 2515160 41 mm 2613160
M 18x 1,5 45 14 2515180 41 mm 2613180
M 20x 1,5 45 14 2515200 41 mm 2613200
M 21 x 1,5 55 16 2515210 -
M 22 x 1,5 55 16 2515220 50 mm 2613220
M 23 x 1,5 55 16 2515230
M 24 x 1,5 55 16 2515240 50 mm 2613240
M 25 x 1,5 65 18 2515250
M 26 x 1,5 65 18 2515260 60 mm 2613260
M 27 x 1,5 65 18 2515270 60 mm 2613270
M 28 x 1,5 65 18 2515280 60 mm 2613280
M 29 x 1,5 65 18 2515290 -
M 30 x 1,5 65 15 2515300 60 mm 2613300
M 32 x 1,5 65 18 2515320 60 mm 2613320
M 33 x 1,5 65 18 2515330 60 mm 2613330
M 34 x 1,5 65 18 2515340 -
M 35 x 1,5 65 18 2515350 60 mm 2613350
M 36 x 1,5 65 18 2515360 60 mm 2613360
M 38 x 1,5 75 20 2515380 70 mm 2613380
M 39 x 1,5 75 20 2515390
M 40 x 1,5 75 20 2515400 70 mm 2613400
M 42 x 1,5 75 20 2515420 70 mm 2613420
M 45 x 1,5 90 22 2515450 85 mm 2613450
M 48 x 1,5 90 22 2515480 85 mm 2613480
M 50 x 1,5 90 22 2515500 85 mm 2613500
M 52 x 1,5 90 22 2515520 85 mm 2613520
M 18 x 2 45 14 2516180 41 mm 2614180
M 20 x 2 45 14 2516200 41 mm 2614200
M 22 x 2 55 16 2516220 50 mm 2614220
M 24 x 2 55 16 2516240 50 mm 2614240
M 26 x 2 65 18 2516260
M 27 x 2 65 18 2516270 60 mm 2614270
M 28 x 2 65 18 2516280 -
M 30 x 2 65 18 2516300 60 mm 2614300
M 33 x 2 65 18 2516330 60 mm 2614330
M 36 x 2 65 18 2516360 60 mm 2614360
M 39 x 2 75 20 2516390 70 mm 2614390
M 40 x 2 75 20 2516400 70 mm 2614400
M 42 x 2 75 20 2516420 70 mm 2614420
M 45 x 2 90 22 2516450 85 mm 2614450
M 48 x 2 90 22 2516480 85 mm 2614480
M 50 x 2 90 22 2516500 85 mm 2614500
Thread inch-Ø Outside Ø mm
Height mm
P/N
NF 1/4 28 20 7 2530010
NF 5/16 24 25 9 2530020
NF 3/8 24 30 11 2530030
NF 7/16 20 30 11 2530040
NF 1/2 20 38 10 2530050
NF 9/16 18 38 10 2530060
NF 5/8 18 45 14 2530070
NF 3/4 16 45 14 2530080
NF 7/8 14 55 16 2530090
L 07
L 08
Glow plug thread repair kits For repairing damaged or for renewing destroyed glow plug threads. When the thread is only slightly damaged the thread is re cut with the finishing tap. Using the reamer the destroyed thread is removed and the drilling for cutting the thread is prepared. The threaded bush is placed last using the turner.
Repair kits 6042100 M 8 x 1,0
6041700 M10x1x10
6041710 M10x1x19
6041500 M10x1,25
6041900 M12 x 1,25
Reamer 6042101 6041701 6041701 6041501 6041960
Tap 6042102 6041702 6041702 6041502 6041950
Finishing tap 6042103 6041703 6041703 6041503
Threaded bush setting tool 6042104 6041704 6041704 6041504
M 8 x 1,0 x 11 mm 6 pcs. 6044085
M10 x 1,0 x 10 mm 6 pcs. 6044090
M10 x 1,0 x 19 mm 6 pcs. 6044095
M10 x 1,25 x 17 mm 6 pcs. 6044125
M12 x 1,25 x 12,7 mm 8 pcs. 6041980
Thread repair kits For repairing or renewing destroyed threads. Using the special drill (3 fluted, titanium-nitrated) the destroyed thread is removed and the drilling for using the threaded bush is introduced. Using the bush setter the cutting threaded bush is then placed. Contents Special drill (3 fluted, titanium-nitrated) 10 cutting threaded bushes Bush setter Special drill 6mm for M4 p/n 930 09 00 10 cutting threaded bushes M4 p/n 930 03 40 Bush setter for M4 p/n 930 05 40 Thread repair kit M4 p/n 930 00 40
Special drill for M 5 p/n 930 09 10 10 cutting threaded bushes M5 p/n 930 03 50 Bush setter for M5 p/n 930 05 50 Thread repair kit M5 p/n 930 00 50 Special drill 9mm for M6 p/n 930 09 20 10 cutting threaded bushes M6 p/n 930 03 60 Bush setter for M6 p/n 930 05 60 Thread repair kit M6 p/n 930 00 60 Special drill 11mm for M8 p/n 930 09 30 10 cutting threaded bushes M8 p/n 930 03 80 Bush setter for M8 p/n 930 05 80 Thread repair kit M8 p/n 930 00 80
L 09
Special drill 13mm for M10 p/n 930 09 40 10 cutting threaded bushes M10 p/n 930 04 00 Bush setter for M10 p/n 930 06 00 Thread repair kit M10 p/n 930 01 00 10 cutting threaded bushes M M10x1,25 p/n 930 04 70 Bush setter for M M10x1,25 p/n 930 06 70 Thread repair kit M M10x1,25 p/n 930 02 00 Special drill 15mm for M12 p/n 930 09 50 10 cutting threaded bushes M12 p/n 930 04 20 Bush setter for M12 p/n 930 06 20 Thread repair kit M12 p/n 930 01 20 10 cutting threaded bushes M12x1,5 p/n 930 04 80 Bush setter for M12x1,5 p/n 930 06 80 Thread repair kit M12x1,5 p/n 930 02 20 Special drill 17mm for M14 p/n 930 09 60 10 cutting threaded bushes M14 p/n 930 04 40 Bush setter for M14 p/n 930 06 40 Thread repair kit M14 p/n 930 01 40 10 cutting threaded bushes M14x1,25 p/n 930 04 90 Bush setter for M14x1,25 p/n 930 06 90 Thread repair kit M14x1,25 p/n 930 02 40 10 cutting threaded bushes M14x1,5 p/n 930 05 00 Bush setter for M14x1,5 p/n 930 07 00 Thread repair kit M14x1,5 p/n 930 02 50 Special drill 19 mm for M16 p/n 930 09 70 10 cutting threaded bushes M16 p/n 930 04 60 Bush setter for M16 p/n 930 06 60 Thread repair kit M16 p/n 930 01 60 10 cutting threaded bushes M16x1,5 p/n 930 05 10 Bush setter for M16x1,5 p/n 930 07 10 Thread repair kit M16x1,5 p/n 930 01 70
Hard metal milling cutters One piece polished, for the machining of welding seams, spot and MIG welds, hardened steel, castings etc. (for use in the pneumatic axial grinder) shank diameter 6 mm. Spherical shape 10 mm Ø p/n 670 01 00 Spherical shape 12 mm Ø p/n 670 01 20 Drip shape 10 x 16 mm p/n 670 21 00 Flame shape 8 x 20 mm p/n 670 10 80 Cylindrical shape 10 mm p/n 670 31 00 Hard metal milling cutters set 5 pcs p/n 670 50 00
L 10
Hacksaw and saw blades Hacksaw for all commercially available saw blades In fully flexible HSS and HSSE quality for the rational sawing of hard, high alloy and stainless steel. Hacksaw S without blades p/n 307 17 00 Blueflex HSS hand saw blade teeth 18 p/n 307 01 80 Blueflex HSS hand saw blade teeth18 double sided p/n 307 05 00 Blueflex HSS hand saw blade teeth 24 p/n 307 02 40 Blueflex HSS hand saw blade teeth 24 double sided p/n 307 05 10 Blueflex HSS hand saw blade teeth 32 p/n 307 03 20 Redflex HSSE hand saw blade teeth 18 p/n 307 11 80 Redflex HSSE hand saw blade teeth 24 p/n 307 12 40 Redflex HSSE hand saw blade teeth 32 p/n 307 13 20 Plaque scraper For removing plaque. Plaque scraper p/n 311 20 00 Plastic chisel and scraper set With 100 spare blades The plastic chisel is particularly well suited to removing the stuck on weights from aluminium rims or for the disassembly of adhesive trim and the like. The scraper is only good as long as it is sharp, therefore we include in this set 100 spare blades. Also the handle is flexible therefore easy to modify depending upon the required application. Plastic chisel and scraper set p/n 311 10 05
Pipe cutter Pipe cutter for copper, brass, aluminium and thin-walled steel tubes Pipe cutter T 03 Cutting range 3-16 mm = 1/8"- 5/8" Length: 50 mm. for close radii Pipe cutter T 03 p/n 312 10 400
Austria Switzerland France Belgium
Pichler Werkzeug GmbH & Co KGPacherstrasse 20A - 6023 Innsbruck