PHASE | VISLINK · 2,3,4,5,6,7,8,10,12,14.16,20 & 24 Mhz Noise figure and receiver thresh-old Noise figure: 3dB typical, 4dB max. Receiver threshold: -92dBm to BER 10-5 (nom. QPSK)

PHASE | VISLINK: Codificadores, Decodificadores e IRDs

UltraCoder & UltraDecoder HEVC HD e 4K UHD………..p. 2

L2174 SD/HD diversity receiver/decoder…………..............p. 6

L2194 SD/HD diversity receiver w/ 1080P/60 decoding…..p. 8

DVE5100 HD/SD IP capable exciter for SNG and ENG…..p. 10

DVE5150 Series H.264 Encoders….………………………...p. 12

IRD5200 DVB-S2 Receiver w/ H.264/MPEG2 Decoding….p. 14

FROM SCENE TO SCREEN

UltraCoder & UltraDecoder HD & 4K UHD end-to-end solutionTransmit HD quality video at half the transmission cost of H.264The only complete HD & 4K UHD encode and decode solution on the market

Same video quality for half the transmission cost with the industry’s first HD & 4K UHD end-to-end video encoder and decoder solutionVislink’s new UltraCoder and UltraDecoder use the very latest HEVC (High Efficiency Video Coding) encoding and decoding techniques to allow scarce bandwidth resource to be utilized more efficiently by transmitting the same video quality using half the bandwidth as compared to H.264, and hence halving the operational costs.

The ability to encode up to four simultaneous HD video streams or one 4K UHD (Ultra High Definition) channel makes this the most advanced end-to-end solution in its class.

What’s more, the solution can deliver a Return on Investment (ROI)* in just three months and is ideal for low usage users who rent capacity adhoc or in situations where transponder space has been rented in advance.

With four times the number of pixels as HD video, Vislink’s 4K UHD solution ensures crystal-clear viewing of every event. Monitor images are sharper, more detailed and delivered in stunning clarity. Designed with operational flexibility in mind, it is the ideal solution design for flyaway or vehicle-mounted solutions, where weight and space are critical.

* Note: ROI is a guideline and will depend on usage and leasing rates.

■ Economical: 50% bandwidth savings when used as part of a satellite communication or microwave system

■ Flexible: Up to four HD or one 4K UHD channel using HEVC encoding

■ Ultra High Definition (4K UHD): Up to 4K UHD P60 resolution ■ Compact rack mount unit: 1RU ½ width ■ Complete end-to-end solution: providing HD & 4K UHD video

encoding and decoding as part of one solution

■ Satellite Newsgathering ■ Electronic Newsgathering ■ IP Networks ■ High-quality contribution and sports events

Typically used for:

SATELLITE

MICROWAVE

CELLULAR

PRODUCTIONSTUDIO

LIVEVIDEO HEVC

ENCODINGHEVC

DECODING

www.vislink.com

VislinkVislink is a leading global technology business specialising in the collection, delivery and management of high quality live video “from scene to screen.” Approximately 70% of all outside wireless broadcast video is transmitted using Vislink equipment, across more than 200,000 systems worldwide. For the broadcast markets, Vislink provides wireless communication solutions for the collection of live news, sport and entertainment as well as software solutions for channel playout automation, channel-in-a-box and video content management. Vislink also provides secure video communications for surveillance and public safety applications such as law enforcement and homeland security.

North America

T: +1 800 490 5700 US Toll Free

T: +1 978 671 5700 US

Europe

T: +44 1442 431300 UK

Middle East

T: +971 4457 9219 UAE

APAC

T: +65 6636 5952 Singapore

Latin America

T: +1 978 671 5700 US

Worldwide

T: +44 (0) 1442 431410 UK

T: +44 (0) 1787 226227 UK

E: [email protected]

Customer SupportAmericas

T: +1 888 777 9221 US Toll Free

T: +1 978 671 5929 US

E: [email protected]

Vislink Offices

[email protected]

Rev 201/09/15

Key Features

■ One box compact and lightweight solution ■ Up to 4 UHF input RF with Max Ratio Combining ■ SD and HD available at 720p and 1080i ■ Capability to support MPEG 2 and MPEG4/H.264 decoding

■ Available for DVB-T COFDM or LMS-T

Typical Applications

■ Event Coverage ■ News gathering ■ Sports Coverage

L2174Multi-Format Reciever & Decoder The L2174 is a 1 RU rack mount chassis demodulator decoder specifically targeted at compact wireless camera & microwave link use. Its Multiple inputs, 4 UHF input RF with Max Ratio Combining and proprietary LMST, ASI (with packet switching) and IP make this a versatile receiver option. The multifunction decoder supports the low delay transmitters and offers generic decoding in both H.264 and MPEG-2.

SPECIFICATIONS

© 2015 Vislink Group. All rights reserved. All other products or services referenced herein are identified by the trademarks or service marks of their respective companies or organisations. Note: Vislink reserves the right to

change specifications without notice. Please contact your representative to confirm current specifications.03/15 ENG

www.vislink.com • [email protected]

RF PARAMETERS

Frequency bands ■ 70 Mhz -8.36 Ghz

Frequency selection ■ Up to 16 pre-set channels, or tuning in 1MHz steps via front panel control

Demodulation ■ DVB-T 2k ■ LMS-T

Demodulation Modes ■ QPSK, 16QAM, 64QAM ■ FEC: 1/2, 2/3, 3/4, 5/6, 7/8 ■ Guard interval: 1/32, 1/16, 1/8, 1/4

LMS-T only available for QPSK and 16 QAM

Bandwidth ■ DVB-T

■ 6, 7, 8MHz ■ LMS-T

■ 2,3,4,5,6,7,8,10,12,14.16,20 & 24 Mhz

Noise figure and receiver thresh-old

■ Noise figure: 3dB typical, 4dB max.

■ Receiver threshold: -92dBm to BER 10-5 (nom. QPSK)

VIDEO AND AUDIO PARAMETERS

Decoding ■ 4.2.0 and 4.2.2 broadcast quality video

■ MPEG2 ■ H.264/MPEG4 and MPEG2, with automatic selection.

Video outputs ■ SDI HD SMPTE-292M (299M) ■ SDI SD SMPTE-259M (272M) ■ Analogue Composite (CVBS), ■ HD down-converted to SD CVBS monitor

ASI outputs ■ 2 x DVB ASI, 188 /204 outputs.

Video Formats ■ 1080i: 1920 x 1080, 25 and 29.5Hz

■ 720p: 1280 x 720, 50 and 59Hz

■ 480i (NTSC): 720 x 480 ■ 576i (PAL): 720 x 576

Latency ■ Automatic selection down to sub 1 frame (20ms), transmitter

■ Encoding profile dependant

Decryption ■ BISS modes 1 and E (factory option)

■ AES

Framelock ■ Genlock input, CVBS black/burst or tri-level sync

Audio outputs ■ Digital: 2 stereo SDI embedded or AES/EBU

■ Analogue: 4 x mono / 2 x stereo

Other Outputs ■ Camera Control interface and alarm output on 6 pin Lemo

■ Remote Control and MEPG data channel on 6-pin Lemo

■ 10/100/1000 Ethernet connections for Video over IP connections

■ 10/100 Ethernet connection for IP- based unit control.

■ USB connector for code updates and profile transfers

Inputs ■ Up to 4x UHF input RF with Max Ratio Combining

■ ASI Input

FLEXIBILITY AND POWER SUPPLY

Monitoring ■ Video picture monitoring on Full Colour TFT front panel display

■ Comprehensive control and monitoring menu via front panel control

■ Demodulator parameters

■ RF Received signal level (dBm and bar graph)

■ C/N, MER, BER (dB and bar graph)

■ Summary front panel alarm/comprehensive internal lock alarms

Remote control ■ Comprehensive remote control and monitoring via Ethernet port / web browser interface.

Software upgrade ■ USB upgrade port

Power Supply ■ 100 - 240Vac; 75W (approximate, depending on configuration)

PHYSICAL & ENVIROMENT

Size and weight ■ 1U Height Half Rack width ■ 210mm x 350mm Deep ■ 1.2kg

Environmental ■ Safe use: 0° to +50°C ■ Humidity: 95% long term

Key Features

■ Direct conversion RF architecture for exceptional adjacent channel performance and excellent sensitivity

■ DVB-T: QPSK, 16QAM & 64QAM; 6, 7, & 8MHz ■ LMS-T: QPSK & 16QAM;10 & 20MHz ■ Variable bandwidth LMS-T; 3, 4, 5, 6, 7, 8, 10, 12, 14, 16, 20 & 24MHz

■ Diversity chaining ASI input for packet diversity

■ Deep interleaving for DVB-T & LMS-T to give exceptional dropout tolerance (*)

■ MPEG-2 4:2:0 & 4:2:2 SD & HD generic ■ MPEG-4 AVC (H.264) Main Profile, High-profile and High 4:2:2 profile, SD & HD decoding

■ ASI input and output ■ Web browser and SNMP control ■ Dual SDI / HD-SDI / CVBS outputs ■ Field upgradeable

(*) with LINK Transmitters

L2194

The Vislink L2194 Receiver is a high-performing, feature-rich SD/HD diversity receiver able to support 1080P/60 decoding for high value wireless camera and central receive applications. Utilizing Vislink’s core technologies, the receiver combines leading-edge MaxRC digital signal processing, with highly configurable FPGA circuitry, providing an abundance of user selectable features, all in one streamlined half width 1 RU rack-mount chassis.

The L2194 incorporates the latest decoding developments giving exceptional performance over a wide range of SD and HD formats. Fully license upgradeable the L2194 will adapt to whatever the requirement

With 1080P 60 / 50 as well as 1080i & 720P decoding along with Vislink’s proprietary LMS-T and Deep-Interleaving demodulation options that will further enhance the already superior operating performance.

SPECIFICATIONS


change specifications without notice. Please contact your representative to confirm current specifications.05/15 ENGRev 1


Demodulator ■ DVB-T: QPSK, 16QAM & 64QAM; 6, 7, & 8MHz

■ LMS-T: QPSK & 16QAM; 10 & 20MHz

■ LMS-T: Variable Bandwidth; 2, 3, 4, 5, 6, 7, 8, 10, 12, 14, 16, 20, & 24MHz

■ Deep interleaving support ■ ASI Packet Switching

Decoder options ■ MPEG-2 4:2:0 & 4:2:2 SD & HD ■ H.264 4:2:0 MP, 8-bit low delay ■ H.264 4:2:0 HP, 8-bit low delay ■ H.264 4:2:2 HP, 8-bit low delay ■ Audio MPEG-2 Layer 1 & 2

Descrambling ■ BISS-1 & E

Inputs ■ 4 x UHF inputs, 70-860MHz. Switchable LNB power.

■ ASI input (ISO/IEC 13818-2 188 bytes)

■ Frame Lock input (black/burst or HD tri-level)

■ Camera Control / Mpeg data channel interface on 6-pin Lemo

■ 10/100/1000 Ethernet connection for Video-over-IP connections

■ 10/100 Ethernet connection for IP-based unit control

■ USB connector for code updates and profile transfers

Outputs ■ 2 x Video outputs; configured (HD)SDI and down-converted confidence quality composite

■ Up to 4 embedded audio outputs

■ ASI output (ISO/IEC 13818-2 188 bytes)

■ Audio output on two 3-pin XLRs (channel 1) and 5-pin Lemo (channel 2)

Physical ■ 1U height, half rack width ■ 210mm [8.3"] x 350mm [13.8"] Deep (excluding connectors)

■ Weight: 1.2kg/2.6 lbs. (approximate)

Power ■ 100 to 240Vac; 75W (approximate, depending on configuration)

Environmental ■ Temperature (operating) 0˚ to 50˚C [32˚ to 122˚F]

■ Humidity (non-condensing) 95%

OPTIONS – BASE UNIT L2194 RECEIVER/ DECODER L2074 DEMODULATOR L2190 DECODER

■ 2-RF INPUTS

■ RF TO ASI DEMODULATION

■ MPEG-2 SD VIDEO AND AUDIO

■ 2-RF inputs

■ RF to ASI Demodulation

■ MPEG-2 SD Video and Audio

Diversity Receiver 2-RF input to 4-RF input upgrade option.

Option Option N/A

Diversity Receiver/Demodulator Deep-Interleaving option.

Option Option N/A

ASI output to ASI input Packet Switching transport stream option.

Option Option N/A

ASI over IP transport option. Option Option N/A

IP input to de-encapsulated ASI option.

Option Option N/A

H.264 Main Profile HD 4:2:0 8-bit, up to 1080P/60 and 1080p/30 license option.

Option N/A Option

H.264 High Profile SD/HD 4:2:2 8-bit, up to 1080P/60 license option.

Option N/A Option

H.264 4:2:0 1080P/60 licence option

Option N/A Option

DVE-5100 SD & HD Exciter with IP Streaming

■ Integral L Band combiner for external L Band carrier addition

■ DVB-S QPSK, 8PSK, 16QAM

■ DVB-S2, QPSK, 8PSK, 16 & 32 APSK

■ 70MHz output option

■ DVB-T/LMS-T COFDM option for IF output

■ 8 audio channels (2 pairs of analogue/AES)

■ Dolby E auto aligner and pass thro’

■ BISS1 / E conditional access

■ Low delay MPEG-2 Encoding (50 mS)

■ ASI output only (Encoder) version available

■ 19” 1U HD SHF solution available with AUC5000 series

■ Remote control via web browser

■ SNMP control

■ IP Streaming output allowing encapsulation of up to 2 ASI signals

■ IP input with de-capsulation of one of four ASI signals, for multiplexing and/or modulation

■ Field upgrade by USB memory stick

5000 SERIES OVERVIEW

Advent’s established lightweight, compact, 1U half rack electronics packages are ideally suited for flyaway or vehicle mounted solutions, where weight and space are at a premium. The 5000 series of electronics can be packaged in different lightweight, ruggedised canvas flight cases, depending on units selected and system configuration.

■ Full range of units available:0

• SD and HD Digital Video Exciter

• IP Modem

• Multiplexer Router

• BUCS

• Antenna and Drive Control units

• System IRD / Redundancy controllers

• Protection Switches

• L Band over fibre modems

■ All units field upgradeable

■ All units have integral web browser facility (where applicable) for RC&M applications

■ A comprehensive range of flight case solutions for 1/2 rack and 19” rack units to suit system configuration, i.e. 3U, 4U, 5U

■ All units can also be fixed together and mounted in a standard 19” flight case or rack within a vehicle

BENEFITS

■ SD & HD MPEG encoder with integrated L Band modulator

■ Integrated HPA controller supporting a wide range of TWTA / SSPA’s

■ HPA control via L Band cable or direct connection

■ SD & HD MPEG-2, 4:2:0/4:2:2 encoding

■ L Band monitor

Digital Video Encoder with Integral ModulatorCompact, Lightweight 1/2 width rack unit


■ Typical Solutions ■ Event Coverage ■ Newsgathering ■ Sports Coverage ■ Maritime Reconnaissance ■ Secure SATCOM

Key Features

■ Compact 1/2 width 19” x 1U rack mountable units ■ 1/4 of the size and 1/6th of the weight of competitors equivalent products

■ Designed for contribution flyaway and DSNG vehicle applications where space and weight are critical

SPECIFICATIONS


change specifications without notice. Please contact your representative to confirm current specifications.


11/13 ENGRD001149 Rev 1

VIDEO PARAMETERS

Inputs ■ HD–SDI / SDI: SMPTE 292M SMPTE 259M / ITU–R BT.656 with embedded audio

■ SD version, composite PAL/NTSC

■ Video Encoding (MPEG2)

SD ■ 420MP@ML 1.5 – 15Mbits ■ 422MP@ML 2 – 50Mbits

HD ■ 420MP@HL 8 – 80Mbits ■ 422MP@HL 8 – 80Mbits

HD Resolutions ■ 1080psf30 / 1080psf29 / 1080psf25 / 1080psf24 / 1080psf23 / 1080p/30 /

1080p/29 / 1080p/25 / 1080p/23 / 1080i/60 / 1080i/59 / 1080i/50 / 1080i/60 / 720p/60 / 720p/50

SD Resolutions ■ 480 x 720 NTSC ■ 480 x 704 NTSC ■ 576 x 720 PAL ■ 576 x 704 PAL

Delay (encoding) ■ Typically less than 50ms

Scrambling ■ BISS 1 & E Encryption

Data Channel ■ RS232 @ 9600 / 19200 / 38400 baud

IP VIDEO TRAFFIC INTERFACE ■ Type: 10 / 100 / 1000 Base–T Ethernet

Protocol ■ IEEE802.3 Ethernet ■ Encapsulation for ASI – RTP (RFC 2250), ARP, IPv4, IGMPv2/3, TCP/UDP

FEC ■ Pro–MPEG Forum Code of Practice #3 release 2 (CoP3) / SMPTE 2022–2007 (Columns and Rows)

■ 1–7 TS packets per IP packet (configurable) with L&D following the range:

■ L*D < 100 ■ 1 < L < 20 ■ 4 < D < 20

Total Bitrate ■ Max 700 Mbit/s (this is for a mux of 4 ASI’s) ■ 1000 Base–T Ethernet ■ Ethernet MTU Length: Max 1500 bytes (IPv4)

AUDIO PARAMETERS

Inputs ■ 2 analogue stereo pairs / 4 mono

■ 600 Ω impedance plus 6 channels embedded in SDI / Linear

■ PCM, Dolby E pass through with Dolby E autio align

RF PARAMETERS

Output Frequency Range ■ L Band 950 to 1750 MHz stepsize 1KHz

■ (70MHz option)

Frequency Stability ■ +/– 2 x 10 e – 8 ■ (10 MHz reference option)

Output Power Level ■ L Band –5 /+5 dBm

Gain Adjustment ■ 40 dB min

Gain Variation ■ +/– 2 dB full band +/– 0.25 dB 24hr @ constant temperature

Spurious ■ –70 dBc / 4 KHz

L Band Monitor ■ Monitor Level –20 dBc

L Band Combiner ■ Combing ratio 5 dB +/–2

Modulation ■ QPSK 1 – 36 Msymb/s Option:

8PSK / 16QAM / 64QAM / DVB–S2 DVBS, DVB–S2, DVB–T 1–45 Msymb/s

FEC

DVBS QPSK ■ FEC rates 1/2, 2/3, 3/4, 5/6, 7/8

DVBS 8PSK ■ FEC rates 2/3

DVBS 16QAM ■ FEC rates 3/4

DVB–T QPSK, 16QAM, 64QAM

■ FEC rates 1/2, 2/3, 3/4, 5/6, 7/8

DVBS–2 QPSK ■ FEC rates 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10

DVBS–2 8PSK ■ FEC rates 3/5, 2/3, 3/4, 5/6, 8/9, 9/10

DVBS–2 8PSK 16/32 APSK ■ FEC rates 3/5, 2/3, 3/4, 5/6, 8/9, 9/10

USER CONFIGURABLE NETWORK & MULTICAST PARAMETERS

Source IP address: ■ IP, Subnet mask, Gateway

Destination IP address: ■ Unicast & Multicast

UDP Ports: ■ User definable

Local MAC address: ■ User definable

PERFORMANCE

THD ■ <0.1% +18 dBm max input level

S/N ■ >66 dB RMS

Frequency response ■ =20 Hz–20 KHz +/– 0.5dB ■ Crosstalk better than 60 dB

Remote Control ■ RS 485 2400 – 9600 band ■ Ethernet / Web browers / SNMP

Web Browser ■ Supporting Internet Explorer 7 & 8, Firefox, Safari and Opera

Encoding ■ MPEG1 Layer 2 128 kbs – 384 kbs / channel (Audio A & B & C)

■ SMPTE 302 2.4MB/s linear PCM / Dolby pass through (Audios A, B, C & D)

■ HPA Control Option ■ Integrated HPA controller for RS485 serial controlled TWTA / SSPA – Xicom, CPI, e2V, Paradise supported, others to order

■ Control via L Band using AUC5000 series converter or via direct cable connection

CONNECTORS

CVBS ■ 75Ω BNC female

(HD) SDI ■ 75Ω BNC female

ASI IN ■ 75Ω BNC female

ASI / 70MHz out ■ 75Ω BNC female

RF Output & Monitor ■ 50Ω N–female

Combiner in ■ 50Ω TNC female

Audio Input ■ 15W D type male breakout to 4 x XLR provided

Data / Remote / Status / HPA Control

■ 15W D type female ■ 2 x USB for field upgrades

Ethernet / Web Interface ■ RJ45 10 / 100 / 1000 Base–T

ENVIRONMENT & PHYSICAL

Temperature ■ Operational: 0°C to +50°C(32°F to 122°F) ■ Storage:–20°C to +70°C (–4°F to 158°F)

Size ■ 210mm wide by 350mm deep (8.27” wide by 13.78” deep) ■ 1U half rack width

Weight ■ 1.9kg approx (4 lbs)

POWER

Frequency ■ 47 to 63 Hz @ <60W

Operating voltage ■ 100 to 240 Vac +/– 10% Web Browser Screenshot showing

IP routing configuration

DVE5100 Rear Panel

DVE5100 Front Panel


■ Event Coverage ■ Newsgathering ■ Sports Coverage ■ Secure SatCom

Key Features

■ 1/4 of the size and 1/6th of the weight of competitors equivalent products

■ HD & SD H.264 4:2:0/4:2:2 encoding

■ Remote control via web browser

DVE5150 Series H.264 Encoders

FEATURES

■ DVE5151 is a Standard Definition & High Definition H.264 video encoder

■ DVE5152 is a dual Standard Definition & High Definition H.264 video encoder

■ 2 pairs of audio channels from embedded SDI

■ BISS1 / E conditional access

■ Low delay H.264 Encoding (20mS) with Vislink decoder

■ SNMP control

■ IP Streaming output allowing encapsulation of up to 2 ASI signals

■ IP input with de-capsulation of one of two IP video signals

■ Field upgrade by USB memory stick

■ IP data extraction from ASI / Demodulator

Vislink’s established lightweight, compact, 1U half rack electronics packages are ideally suited for flyaway or vehicle mounted solutions, where weight and space are at a premium. The 5000 series of electronics can be packaged in different lightweight, ruggedised canvas flight cases, depending on units selected and system configuration.

■ Compact 1/2 width 1U rack mountable units

■ Designed for contribution flyaway and DSNG vehicle applications where space and weight are critical

■ Full range of units available:

• SD and HD Digital Video Exciter

• IP Modem

• Multiplexer Router

• BUCS

• Antenna and Drive Control units

• System IRD / Redundancy controllers

• Protection Switches

• L Band over fibre modems

• Diversity Receivers

■ All units field upgradable

■ All units have integral web browser facility (where applicable) for RC&M applications

■ A comprehensive range of flight case solutions

■ All units can also be fixed together and mounted in a standard 19” flight case or rack within a vehicle

Compact H.264 Digital Video Encoder – DVE5151 with optional second encoder – DVE5152 or integrated COFDM MaxRC diversity receiver – DVE5174

SPECIFICATIONS




07/15 ABCRD001871 Rev 1

VIDEO PARAMETERS

Inputs ■ HD–SDI / SDI: SMPTE 292M SMPTE 259M / ITU–R BT.656 with embedded audio

Video Encoding (H.264)

SD ■ 420HP@L3 0.5 – 25Mbits ■ 422HP@L3 2 – 25Mbits

HD ■ 420HP@L4 1 – 41Mbits ■ 422HP@L4 1 – 41Mbits

HD Resolutions ■ HD 1080i/60 ■ HD 1080i/59 ■ HD 1080i/50 ■ HD 1080i/60 ■ HD 720p/60 ■ HD 720p/50

SD Resolutions ■ 480 x 720 NTSC ■ 480 x 704 NTSC ■ 576 x 720 PAL ■ 576 x 704 PAL

Latency (encoding) ■ H.264 20mS in low delay mode

Scrambling ■ BISS 1 & E Encryption3

ENVIRONMENT & PHYSICAL

Temperature ■ Operational: 0°C to +50°C (32°F to 122°F)

■ Storage: –20°C to +70°C (–4°F to 158°F)

Size ■ 210mm wide by 350mm deep (8.27” wide by 13.78” deep)

■ 1U half rack width

Weight ■ <1.5kg approx (4 lbs)

POWER

Frequency ■ 47 to 63 Hz @ <50W

Operating voltage ■ 100 to 240 Vac +/– 10%

HARDWARE OPTIONS ■ DC Power option ■ Second encoder - DVE5152 ■ Integrated 4-way diversity demodulator - DVE5174

AUDIO PARAMETERS

Inputs ■ 2 stereo pairs ■ Dolby E pass through / AC3 pass through

AUDIO PARAMETERS PERFORMANCE CONNECTORS

(HD) SDI ■ 75Ω BNC female

ASI IN ■ 75Ω BNC female

ASI out ■ 75Ω BNC female

Remote / Status ■ 15W D type female ■ USB for field upgrades

Ethernet / Web Interface ■ RJ45 10 / 100 / 1000 Base–T

IP VIDEO TRAFFIC INTERFACE ■ Type: 10 / 100 / 1000 Base–T Ethernet

Protocol ■ IEEE802.3 Ethernet ■ Encapsulation for ASI – RTP (RFC 2250), ARP, IPv4, IGMPv2/3, TCP/UDP

FEC ■ Pro–MPEG Forum Code of Practice #3 release 2 (CoP3) / SMPTE 2022–2007 (Columns and Rows)

■ 1–7 TS packets per IP packet (configurable) with L&D following the range:

■ L*D < 100 ■ 1 < L < 20 ■ 4 < D < 20

Total Bitrate ■ Max 100 Mbit/s (this is for a max of 4 ASI’s)

■ 1000 Base–T Ethernet ■ Ethernet MTU Length: Max 1500 bytes (IPv4)

USER CONFIGURABLE NETWORK & MULTICAST PARAMETERS

Source IP address: ■ IP, Subnet mask, Gateway

Destination IP address: ■ Unicast & Multicast

UDP Ports: ■ User definable

PERFORMANCE

THD ■ <0.1% +18 dBm max input level

S/N ■ >66 dB RMS

Frequency response ■ =20 Hz–20 KHz +/– 0.5dB ■ Crosstalk better than 60 dB

Encoding ■ MPEG1 Layer 2 128 kbs / 256kbs / 384 kbs / channel (Audio A & B)

■ SMPTE 302 2.4MB/s / Dolby E & AC3 pass through (Audio B only)

Remote Control ■ Ethernet: Web browsers / SNMP

Web Browser ■ Supporting Internet Explorer 7, 8 & 9. Firefox, Safari and Opera

FEATURES

■ 2 x L-band input with L-band loop-through monitor

■ 1 x VHF/UHF* and 1 x ASI inputs

■ ASI decapsulation from IP input*

■ ASI encapsulation onto IP output*

■ LNB/Downconverter powering

■ L3025 Downconverter powering via VHF/UHF input

■ DVB-S QPSK demodulation

■ DVB-S2 QPSK, 8PSK, 16APSK & 32APSK demodulation*

■ ASI Output

■ BISS 1/E Descrambling,

■ MPEG-2 4:2:0 & 4:2:2 SD generic and ultra low delay decoding (with Vislink Encoder)

■ MPEG-2 4:2:0 & 4:2:2 HD generic and ultra low delay decoding* (with Vislink Encoder)

■ H.264 4:2:0 Main Profile and High-profile SD and HD Decoding*

■ H.264 4:2:2 8,9 & 10-bit High-profile SD & HD decoding*

■ Web browser and SNMP control,

■ SDI-HD/SD and CVBS outputs with embedding of up to 4 pairs of decoded audios

■ Independent output of Audio Pairs #1 and #2 as analog audio or balanced AES on LEMO connector (XLR breakout lead supplied)

■ Field upgradeable via USB

■ Typical uses include:

• Lightweight Monitoring IRD for SNG applications

• Satcom Contribution or Cable-Head Receiver

• ENG Point-to-Point DVB-S2 Receiver using L3025 Downconverter

(*) optional license key upgrade

The IRD5200 is the highest performing feature-rich SD/HD Contribution IRD available for lightweight SNG Flyaway or Terrestrial ENG receive applications. Utilising Vislink’s core technologies the IRD5200 combines leading edge high order DVB-S2 demodulation with highly configurable FPGA circuitry providing an abundance of user selectable features all in one streamlined 19” x 1RU Half-Rack Width unit. This revolutionary concept for SNG /ENG and OB receive operations reduces the complexities and operating costs of today’s economically challenged businesses.

The 5200 IRD accepts up to two L band and one 58-860MHz RF input, in addition to two individual ASI inputs, RF signal inputs, providing reliable and comprehensive coverage for any SNG or ENG/OB receiving site. The integral demodulator can be configured for DVB-S QPSK and DVB-S2 schemes from QPSK through to 32APSK

In addition, with the relevant software license, the IRD5200 will accept ASI over IP input (decapsulating an ASI video from an IP transport stream and can encapsulate up to two ASI videos into an IP stream for routing to an alternate destination for decoding.

With the relevant license the integral decoder will decode MPEG2 SD/HD 4:2:0 and 4:2:2 video (including Vislink’s ultra low delay encoding) in addition to H.264 4:2:0 SD/HD and 4:2:2 10bit HD video.

A powerful, yet simple to operate, web-based graphical user interface (GUI) provides complete remote control and monitoring for the receiver by means of an integrated Ethernet/SNMP (RJ45) interface. This can be operated by connecting the IRD to a laptop or other device where the control screen will function in most web browsers. This further reduces capital equipment expenditures by eliminating the need for expensive third party remote control systems.

The IRD5200 is part of a complete suite of units aimed at high quality or versatile contribution links where live video or content is required to be routed back to base via Satellite, Microwave or IP connectivity. The range includes HD and SD Video Encoders, DVB-S, DVB-S2, DVB-T and LMS-T Modulators, IP Satellite Modems, Diversity Receivers, IRDs and associated units. All units utilise a 19”x1RU half rack width housing for compactness and extremely light weight. This packaging has proved its worth in the portable applications where these type of units are typically deployed.

DVB-S2 Satcom and ENG IRD

IRD5200DVB-S2 Receiver with H.264 / MPEG2 Decoding

SPECIFICATIONS




IRD5200 BASE CONFIGURATION ■ Base Unit Part Number: 9002965

■ 2 x L band Inputs and 1 x L band loopthrough

■ 2 x ASI inputs ■ 1 x ASI output

■ DVB-S QPSK Demodulation 950-2150MHz

■ MPEG2 SD 4:2:0 and 4:2:2 Generic and Vislink Low Delay Decoding

■ Integral web browser control

■ SDI-SD and CVBS Video outputs

■ 2-pair audio decoding (with upgrade to 4-pair decoding when available)

DEMODULATOR:

DVB-S ■ QPSK

DVB-S2 ■ QPSK / 8PSK / 16APSK / 32APSK

L Band Input Range ■ 950-2150MHz

VHF/UHF input range ■ 58-860MHz

Symbol Rate ■ Up to 45Msymbols

DECODER:

SD ■ MPEG-2 4:2:0 & 4:2:2

HD ■ MPEG2 4:2:0 & 4:2:2 ■ Low delay MPEG-2, 4:2:0 & 4:2:2

■ H.264 4:2:0 MP, 8-bit ■ H.264 4:2:2 HP, 8-bit ■ H.264 4:2:2 HP, 10-bit

Audio ■ 4 pairs Audio MPEG-2 Layer 1 & 2,

Descrambling: ■ BISS-1 & E ■ AES 128 & 256bit (future software upgrade)

Inputs: ■ 2 x L band RF inputs - F-Type(f). Switchable LNB power

■ 1 x UHF inputs, 58-860MHz – BNC(f). Switchable Downconverter power

■ 1 x ASI input – BNC(f) (ISO/IEC 13818-2 188 bytes),

■ 10/100/1000 Ethernet connection for Video-over-IP connections - RJ45

■ 10/100 Ethernet connection for IP-based unit control – RJ45

■ USB2 connector for code updates and profile transfers

Outputs ■ SDI-SD/HD/Composite Video – BNC(f)

■ ASI output – BNC(f) (ISO/IEC 13818-2 188 bytes),

■ L band Loopthrough – BNC(f) ■ Audio Pairs #1 and #2 (analog or AES) – LEMO 4 x XLR3P breakout lead

ENVIRONMENTAL & PHYSICAL

Temperature Operational ■ 0°C to +50°C (32°F to 122°F)

Temperature Storage ■ –20°C to +70°C (–4°F to 158°F)

Size ■ 210mm wide x 350mm deep (8.27” wide x 13.78” deep)

■ 1U half rack width

Weight ■ 1.5 Kg (3.5lbs)

Power ■ Frequency ■ 47 to 63 Hz @ <100W

Operating Voltage ■ 100 to 240 Vac +/– 10%

Power ■ IEC Input ■ 100-240VAC ±10%, 47-63Hz <100W

06/14 ENGRD000528 Rev 1

IRD5200 in AFC5003 Half Width Lightweight Flightcase

with 5100 Exciter and AUC5814 BUC

IRD5200 LICENSE KEY UPGRADES

9002230 58-860MHz input enable

L9556 ASI over IP Encapsulation

L9557 ASI over IP Decapsulation

L9565 MPEG2 HD (Generic) upgrade

L9564 MPEG2 HD (Ultra Low delay) upgrade

L9560 H.264 4:2:0 MP & HP SD/HD Decoding

L9561 H.264 4:2:2 10-bit HP SD/HD Decoding

060-5858 DVB-S2 QPSK/8PSK Upgrade

9000415 DVB-S2 16APSK/32APSK Upgrade

PHASE ENGENHARIA

EXCLUSIVE REPRESENTATIVE:

PHASE Engenharia Ind. e Com. Ltda.

Av. Olegário Maciel 231, Lojas 101 a 105

Barra da Tijuca | Rio de Janeiro, RJ | CEP 22 621 200

Tel +55.21.2493.0125

Av. Ibirapuera 2.907, Conj. B306 & 7 - Ed. Conv. Corp. Plaza – Torre C

Indianópolis | São Paulo-SP | CEP 04029-200

Tel +55 11 3589-0125

[email protected] | www.phase.com.br

PHASE | VISLINK · 2,3,4,5,6,7,8,10,12,14.16,20 & 24 Mhz Noise figure and receiver thresh-old Noise figure: 3dB typical, 4dB max. Receiver threshold: -92dBm to BER 10-5 (nom. QPSK)

Documents