Let’s get started! with a laser Metal marking logos on tools and parts with a CO 2 laser is now possible. Using a simple three-step process, you can utilize a low-cost CO 2 laser system for permanently marking all types of metal parts and tools. Traditionally, you would have needed an expensive YAG or fiber laser system to engrave into bare metal. With a CO2 laser, you have several advantages that are perfect for many applications. Contact us to find out how to set up a demonstration of the laser in action! Call +1 303.277.1188 or email [email protected]. Affordability . The cost of a CO 2 laser systems is about 30-50% less than a comparable Fiber or YAG system - perfect for a lower budget. Versatility . The same laser you are using to mark metal can also be used to cut plastic, etch acrylic, engrave glass, wood, and much more by simply changing the speed and power settings of the laser. Any Size Part . Your only limit is the size of the engraving table (which ranges from 16” x 12” x 4.5” (405 x 305 x 114 mm) all the way up to 36” x 24” x 12” (914 x 610 x 305 mm). Barcode & Serial Number Marked on Brass Permanent Metal Marking Logo Marked on Steel 16371 Table Mountain Parkway Golden, CO 80403 +1 303.277.1188 888.437.4564 www.epiloglaser.com [email protected]
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Let’s get started!
with a laserMetal marking logos on tools and parts with a CO2 laser is now possible. Using a simple three-step process, you can utilize a low-cost CO2 laser system for permanently marking all types of metal parts and tools.
Traditionally, you would have needed an expensive YAG or fiber laser system to engrave into bare metal. With a CO2 laser, you have several advantages that are perfect for many applications.
Contact us to find out how to set up a demonstration of the laser in action! Call +1 303.277.1188 or email [email protected].
Affordability . The cost of a CO2 laser systems is about 30-50% less than a comparable Fiber or YAG system - perfect for a lower budget.
Versatility . The same laser you are using to mark metal can also be used to cut plastic, etch acrylic, engrave glass, wood, and much more by simply changing the speed and power settings of the laser.
Any Size Part . Your only limit is the size of the engraving table (which ranges from 16” x 12” x 4.5” (405 x 305 x 114 mm) all the way up to 36” x 24” x 12” (914 x 610 x 305 mm).
Barcode &
Serial Number
Marked on B
rass
Permanent Metal Marking
Logo M
arked on
Steel
16371 Table Mountain ParkwayGolden, CO 80403
+1 303.277.1188 888.437.4564
Looking to Etch Bare Metal without a Marking Compound? If you are looking for a mark on bare metal without using a metal marking compound, take a look at the FiberMark laser system. By adapting the flying-optic motion system that made our lasers famous, we incorporate a 1062 nm wavelength Ytterbium Pulsed Fiber Laser to engrave directly into metal and mark engineered plastics.
Contact us today at +1 303-277-1188 for samples engraved on both systems.
How to Use Metal Marking Compounds with the Laser
Step 1) Apply a thin coat of a metal marking compound, such as CerMark or TherMark, directly to the metal you want to mark. You can use either a spray can application or paste version. Let the part dry for a few minutes.
Step 2) Place your part (or jig of parts) in the laser and print your job to the laser.
Step 3) After the part has been marked, simply wash off the excess metal marking compound with water. The resulting laser mark will be a crisp, permanent, high-contrast mark.
16371 Table Mountain ParkwayGolden, CO 80403
+1 303.277.1188 888.437.4564
05/2011
Tools Marked with
a CO2 Laser
Related Documents
