Optional Image PeopleNet TABLET Installation Guide Version 1.1 A guide for new TABLET & new OBC installations. (Refer to the PeopleNet TABLET Upgrade Guide if upgrading from classic OBC to TABLET.)
Optional Image
PeopleNet TABLET Installation Guide Version 1.1 A guide for new TABLET & new OBC installations. (Refer to the PeopleNet TABLET Upgrade Guide if upgrading from classic OBC to TABLET.)
2
© 2010 PeopleNet Communications. All rights reserved.
Revisions
Version Description of Version Date Completed
1.0 Initial Draft – Pete L. 12/06/2010
1.1 Potential Candidate – Matt H. 1/10/11
1.2 Release Candidate – Matt H. 1/13/11
1.3 Updated Tablet Photo-Josh 2/3/11
PeopleNet TABLET is a trademark of PeopleNet Communications Corporation.
3
© 2010 PeopleNet Communications. All rights reserved.
Table of Contents
REVISIONS ............................................................................................................ 2
TABLE OF FIGURES ................................................................................................ 4
BEFORE YOU BEGIN ............................................................................................... 5
PeopleNet System Installation Manual ............................................................................... 6
TABLET ............................................................................................................................. 6
TABLET Dock Install Kit ..................................................................................................... 7
DC-DC Power Supply Kit ................................................................................................... 8
Additional Parts .......................................................................................................................... 8
Speaker Kit (Optional equipment) ...................................................................................... 9
INSTALLATION ...................................................................................................... 11
TABLET Installation ......................................................................................................... 12
Mounting the TABLET Dock ..................................................................................................... 12
DC-DC Installation ........................................................................................................... 13
Connecting the DC-DC Power Supply to the PeopleNet System .............................................. 13
Mounting the DC-DC Power Supply ......................................................................................... 14
Connecting Power to the DC-DC Power Supply ....................................................................... 15
Plugging in TABLET Dock, Keyboard, and Speaker ................................................................. 16
FIRMWARE DOWNLOAD ......................................................................................... 17
g3 Firmware Download Process ...................................................................................... 18
SYNCHRONIZATION............................................................................................... 19
TABLET-OBC Synchronization Process .......................................................................... 20
INSTALLATION EXAMPLES ...................................................................................... 21
Three Views of a Tablet Installation ................................................................................. 22
STILL HAVE QUESTIONS? ..................................................................................... 25
PeopleNet University ........................................................................................................ 26
4
© 2010 PeopleNet Communications. All rights reserved.
Table of Figures
FIGURE 1: PEOPLENET INSTALLATION MANUAL ......................................................... 6
FIGURE 2: THE TABLET DEVICE ............................................................................. 6
FIGURE 3: TABLET DOCK AND INSTALL KIT ............................................................. 7
FIGURE 4: DC-DC POWER SUPPLY KIT ................................................................... 8
FIGURE 5: SPEAKER KIT (OPTIONAL) ....................................................................... 9
FIGURE 6: GENTLY TIGHTEN CONNECTORS UNTIL SNUG .......................................... 13
FIGURE 7: DC-DC POWER SUPPLY WIRES ............................................................ 15
FIGURE 8: TABLET DOCK CONNECTIONS .............................................................. 16
FIGURE 9: USB CONNECTION WITH ELECTRICAL TAPE AND ZIP TIE ........................... 16
FIGURE 10: MOUNTED TABLET BRACKET ................................................................ 22
FIGURE 11: MOUNTED TABLET DEVICE; NO KEYBOARD ........................................... 22
FIGURE 12: MOUNTED TABLET DEVICE; FRONT VIEW .............................................. 23
Before You Begin
An inventory of documentation and hardware before you install a new TABLET.
6
PeopleNet System Installation Manual
© 2010 PeopleNet Communications. All rights reserved.
PeopleNet System Installation Manual
You need to complete some of the procedures in the PeopleNet Installation Manual before proceeding with this guide. These include the following three procedures:
• Mounting the g3 onboard computer (OBC)
• Mounting and connecting antennas
• Connecting the Main Cable to the OBC and the vehicle’s power source
Figure 1: PeopleNet Installation Manual
TABLET
This is the TABLET device itself and the TABLET in the TABLET Dock.
Figure 2: The TABLET device
Part #: M-010-0250
7
TABLET Dock Install Kit
© 2010 PeopleNet Communications. All rights reserved.
TABLET Dock Install Kit
The TABLET Dock Install Kit contains the following items pictured in Figure 3.
Qty Part Description Part #
1 TABLET Dock H-053-0503
1 TABLET Interface Cable L-016-0510
1 “L” Support Brace H-050-0110
4 8-32 x 1” PH PAN H-048-0500
Figure 3: TABLET Dock and Install Kit
Part #: M-010-0256
8
DC-DC Power Supply Kit
© 2010 PeopleNet Communications. All rights reserved.
DC-DC Power Supply Kit
The DC-DC Power Supply Kit contains the following items pictured in Figure 4.
Part Description
DC-DC power supply with power cord
15 Amp fuse and holder
Figure 4: DC-DC Power Supply Kit
Additional Parts
In addition to the parts listed above and shown in Figure 4, you will need the following parts:
Additional Parts
Zip ties to secure excess cabling
4 screws to mount the power supply
1 butt connector to attach the fuse holder
Electrical tape
Part #: E-006-0505
9
Speaker Kit (Optional equipment)
© 2010 PeopleNet Communications. All rights reserved.
Speaker Kit (Optional equipment)
The Speaker Kit includes the following items pictured in figure 5.
Qty Part Description Part #
1 Speaker H-040-0501
1 Speaker Mounting Bracket
2 Thumb Screws
Figure 5: Speaker Kit (Optional)
Installation
Installation instructions for TABLET and related hardware.
12 © 2010 PeopleNet Communications. All rights reserved.
TABLET Installation
TABLET Installation
Before proceeding, verify that you have completed the procedures in the PeopleNet Installation Manual through page 28. These include the following three procedures:
• Mounting the g3 onboard computer (OBC)
• Mounting and connecting antennas
• Connecting the Main Cable to the OBC and the vehicle’s power source
Once you have verified that they are completed, proceed with “Mounting the TABLET Dock” below.
Mounting the TABLET Dock
You will need the TABLET Dock Installation Kit for this procedure.
1. Determine a physical mounting location for the TABLET Dock that will not
• Impede the driver’s vision, or
• Cause damage to the truck from the weight of the device.
Refer to “Installation Examples” on page 22 for pictures of a mounted TABLET Dock.
2. Bolt the TABLET Dock to the “L” Support Brace.
3. Secure the “L” Support Brace to the dash.
4. Verify that both the “L” Support Brace and the TABLET Dock are securely mounted.
5. Place the TABLET into the TABLET Dock.
6. Lock the TABLET in place with the locking mechanism on the top of the TABLET Dock.
The TABLET Dock is now mounted.
13 © 2010 PeopleNet Communications. All rights reserved.
DC-DC Installation
DC-DC Installation
You will need the DC-DC Power Supply Kit for the following procedures.
Connecting the DC-DC Power Supply to the PeopleNet System
1. Locate the two blue barrel connectors; one from the Main Cable (for explanation, refer to the PeopleNet Installation Manual), and one from the TABLET Interface Cable.
2. Plug both connectors into their corresponding connectors on the DC-DC Power Supply.
3. Use pliers to gently tighten the connectors until snug.
Figure 6: Gently Tighten Connectors until Snug
14 © 2010 PeopleNet Communications. All rights reserved.
DC-DC Installation
Mounting the DC-DC Power Supply
1. Determine a location for the DC-DC Power Supply that meets the following requirements:
• Safe from electrical contacts. Since the DC-DC Power Supply box is metal and connected directly to ground, it MUST NOT come into contact with a positive power source. If the DC-DC Power Supply box were to touch an unprotected source of power, it would short out the system and could potentially cause a fire.
• Securely mounted. The DC-DC Power Supply must be held in place by four screws. If it cannot be secured by four screws, zip ties can be used to secure it to a solid object, such as a support brace behind the dash.
• Continuously cool and dry. The DC-DC Power Supply must be kept away from major heat sources and protected from the elements, such as water.
2. Mount the DC-DC Power Supply in the determined location with four (4) screws and zip ties, as necessary.
CAUTION: The case of the DC-DC Power Supply is connected directly to ground. Do NOT allow it to come into contact with any power sources. The supplied 15 Amp fuse will not protect against this condition.
15 © 2010 PeopleNet Communications. All rights reserved.
DC-DC Installation
Connecting Power to the DC-DC Power Supply
Keep Figure 7 and the following colors in mind as you proceed with this procedure:
Figure 7: DC-DC Power Supply Wires
Wire Color Description
Red Constant +12 Volts (Not Switched)
Black Ground
1. Using a butt connector, attach the red wire from the DC-DC Power Supply to the fuse holder.
2. Connect the other end of the fuse holder to a 15 Amp power source.
This may be the same source that is used for g3 power.
Important: Do not connect the 15 Amp fuse in series with the 5 Amp fuse; go directly to the vehicle’s power source.
3. Secure the black, grounding wire and silver, shielding wire to a secure, reliable ground.
4. Verify that you are ready to power up the TABLET.
5. Insert the 15 Amp ATC fuse into the fuse holder.
16 © 2010 PeopleNet Communications. All rights reserved.
DC-DC Installation
Plugging in TABLET Dock, Keyboard, and Speaker
1. Connect the male 12 pin connector on the TABLET Interface cable to the back of the TABLET Dock.
Figure 8: TABLET Dock connections
2. Connect the USB keyboard to either USB pigtail on the TABLET Dock
a. Wrap the end of the unused USB pigtail with electrical tape and secure the wire
3. Wrap electrical tape around the USB connection (for protection), and secure the USB cables with a zip tie to form strain-relief loop.
Figure 9: USB Connection with Electrical Tape and Zip Tie
4. (Optional equipment) Connect the speaker to the TABLET Dock
a. Connect the male stereo plug of the speaker to the back of the TABLET Dock
b. Connect the paired red and black wires from the speaker to the grey speaker pigtail of the TABLET Interface cable. (Remove the 2-pin connector from the pigtail and use butt connectors to connect red to red and black to black)
Firmware Download
Process for updating the g3 OBC firmware.
18 © 2010 PeopleNet Communications. All rights reserved.
g3 Firmware Download Process
g3 Firmware Download Process
This process updates the g3 firmware to be compatible with the TABLET.
1. Insert the provided fuses to power up TABLET and the g3.
• If the onboard computer (OBC) has the correct code, TABLET will move directly to Process Installation for synchronization (see “TABLET-OBC Synchronization Process” on page 20).
• If the OBC needs a firmware update, the PeopleNet Download Utility will automatically launch and will ask you, “….Would you like to update the OBC?”
2. Press Yes to continue.
The download will begin and last about 7-10 minutes.
The screen will display “Download Complete” as each software packet is successfully downloaded.
The download will not be completed until the screen displays “OBC Upgrade Successful.”
3. Press “OK” and proceed to “TABLET-OBC Synchronization Process” on page 20 for synchronization.
Synchronization
Process for activating the TABLET and the OBC.
20 © 2010 PeopleNet Communications. All rights reserved.
TABLET-OBC Synchronization Process
TABLET-OBC Synchronization Process
Starting at the Process Installation window with the prompt, “…Would you like to process an installation?”
1. Select Yes.
You are prompted with “Is this a new installation?”
2. If the g3/OBC is brand new, select “Yes”.
a. If the g3/OBC is currently active in the PFM(PeopleNet Feet Manager), select “No”
3. Enter your Installer Number and press the Tab key.
4. Enter your Truck Number.
5. Press SUBMIT.
• If the 2nd
green LED stops flashing and the screen has not changed, press Data Call to continue the installation.
• The screen will eventually change and you will receive a message confirming successful installation.
Process Installation is now complete.
Important: If the activation message is not displayed, contact PeopleNet Support at 888-346-3486.
Installation Examples
Pictures from a successful installation.
22 © 2010 PeopleNet Communications. All rights reserved.
Three Views of a Tablet Installation
Three Views of a Tablet Installation
Figure 10: Mounted Tablet Bracket
Figure 11: Mounted Tablet Device; No Keyboard
23 © 2010 PeopleNet Communications. All rights reserved.
Three Views of a Tablet Installation
Figure 12: Mounted Tablet Device; Front View
Still Have Questions?
If you still have questions or want additional training, please take advantage of the additional resources in this section.
26 © 2010 PeopleNet Communications. All rights reserved.
PeopleNet University
PeopleNet University
PeopleNet University is an online resource center including Training Opportunities, PeopleNet Installation Certification, and Resources including Manuals & Reference Cards; as well as information about PeopleNet’s Professional Services offerings.
There are two ways to access PeopleNet University:
1. Click on the PeopleNet University icon on the main page when logging into the PFM. The page is always available in the PFM by clicking the Refresh button for your web browser.
2. Type www.peoplenetuniversity.com into a browser window.
US Headquarters Canada Contact
PeopleNet PeopleNet Canada (888) 346-3486
4400 Baker Road 1100 Burloak Dr. • Suite 300 (952) 368-9320 Fax
Minnetonka, MN 55343-8684 Burlington, Ontario L7L 6B2 [email protected]
USA Canada www.peoplenetonline.com
©2009 PeopleNet Communications Corporation. All rights reserved. This information is subject to change without notice.