Subject to change without notice Peerless Pump Company Indianapolis, IN 46207-7026 VERTICAL TURBINE PUMPS Right Angle Gears SECTION 110 Page 1 January 2, 2007 Shaft Guarding for Horizontal Mounted Spicer Universal Joint Drive Shafts A shaft guard must be supplied with all Spicer shafts (see Spicer price list for pricing) and all quotations and orders must include or specify shaft guard when drive shafts are quoted or ordered. They are relatively easy to install and a 2 inch wide opening runs the full length of the bottom of the guard to facilitate shaft lubrication. IMPORTANT: These guards do not comply with California Code or OSHA requirements. If shaft guard is specified to meet OSHA requirements by customer we cannot accept order. Please refer to Section 10 page 8 for instructions concerning orders with OSHA compliance specifications. We strongly recommend that guarding requirements and design be resolved with customer before entering order and that design be in compliance with any local or state codes. The standard guard furnished (as shown below) only provides minimal protection for most commercial and industrial applications where equipment is installed in limited access buildings or enclosures.
16
Embed
Peerless Pump Company VERTICAL TURBINE … lit/Peerless Turbines/Section... · Peerless Pump Company Indianapolis, IN 46207-7026 VERTICAL TURBINE PUMPS Right Angle Gears SECTION 110
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Subject to change without notice
Peerless Pump Company Indianapolis, IN 46207-7026
VERTICAL TURBINE PUMPS Right Angle Gears
SECTION 110 Page 1 January 2, 2007
Shaft Guarding for Horizontal Mounted Spicer Universal Joint Drive Shafts
A shaft guard must be supplied with all Spicer shafts (see Spicer price list for pricing) and all quotations and orders must include or specify shaft guard when drive shafts are quoted or ordered.
They are relatively easy to install and a 2 inch wide opening runs the full length of the bottom of the guard to facilitate shaft lubrication.
IMPORTANT: These guards do not comply with California Code or OSHA requirements. If shaft guard is specified to meet OSHA requirements by customer we cannot accept order. Please refer to Section 10 page 8 for instructions concerning orders with OSHA compliance specifications.
We strongly recommend that guarding requirements and design be resolved with customer before entering order and that design be in compliance with any local or state codes. The standard guard furnished (as shown below) only provides minimal protection for most commercial and industrial applications where equipment is installed in limited access buildings or enclosures.
VERTICAL TURBINE PUMPS
50 Hz Motor Rpm
1470 1760 2112 2347 2640 3080 List Wt.Part No. Part Part Price Lbs.
SC1910 268646810 No Part Nos. 268646902 750 996 1126 1225 - - $13,877 180
Peerless Pump
Shaft Size
Maximum Bhp @ 1760 Rpm Output speed 2
1 Note: Customer must supply mating shaft diameters, keyway dimension, driver Bhp & Rpm for all non Peerless Pump supplied equipment.
Peerless Pump
Peerless Pump
2 Standards for shaft sizings are: B-10 life of 5000 hours; working installation angle of 3 degrees; Diesel engines without any
Right Angle Gear Ratio
Engine Rpm
50 Hz & Diesel Engine Driven Units
and 50 Hz 4 Pole Horizontal Motors Speed Increasing Right Angle Gear for 1760 RPM output
All Power Transmission Short Coupled Universal Joint Drive Shafts for Direct
List price includes shaft, dynamic balancing, fastener kits, large ( through 61)and standard companion (71 & Up) flanges with set screw over keyway and set screw @ 90 deg from keyway
and shaft guard.
Connected Vertical Turbine Fire Pumps with Right Angle Gears. 2 or 4 Stroke Diesel Engines,
1000G 2,950 CF CF 9,770 3,910 INCL 2,360 210 610 1Prices are for 1760 rpm pump speed. Contact factory for pump speeds other than 1760 rpm.
2Export boxes are made from heat treated lumber.
Model
NET PricesLIST Prices
Amarillo Gear Company manufactures right angle gear drives for applications up to 3,000 horsepower. Contact factory for prices and availability of gear drives
not described in the catalog.
Type Marine
Package
Water
Cooler
Spec.
Rotation
Paint
Color
Export
Box2
* Model 40 is available with either a 12" BD (40A) or 16½" BD (40B)
I. Hollow shaft, types: (non‐reverse included)SL: Opposed Thrust RatingS: Standard Heavy Thrust RatingSH: Extra Heavy Thrust RatingC: Manual CombinationCA: Automatic Combination
II. Solid Shaft, types: (non‐reverse included)SS: Heavy Thrust Rating
III. Marine Package includes stainless steel hardware, stainless steel oil tube and epoxy paint. External Marine Heat Exchanger is included on model 100A and larger.
IV. Check following applications with engineering as price additions may be required:1. Steam turbine or other high speed driver. 2. Pump speeds slower than indicated in catalog.3. Pump speed greater than 1800 rpm.
C/F = Contact Factory N/A = Not Available INCL = Included
MODEL M80P
Special Rotation Fig.2,3,4
Extra Heavy Thrust
Vertical Solid Shaft
Opposed Thrust
BearingsMarine
PackageCopper Water Cooler
Net Export Box
Sprag Non-Reverse
Slant Drives
Propeller Pump Drives are fan cooled and require no additional water cooling. Marine Package includes stainless steel hardware, nameplate, oil tube, and epoxy paint. If sea water cooler, or shell and tube external cooler is required, please contact factory. All prices are subject to change without notice. . VISIT OUR WEBSITE @ WWW.DERANGEAR.COM