Pediatric Examination Tabel

FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY

Model Numbers:

SF-1918 Part No. 004-0559-00 Rev. A (10/8/2012)

PediatricExamination Table

640 (all)

Service andParts Manual

http://www.documark.com/printer.asp?partnumber=004-0559-00

* Indicates multiple pages due to model / serial number break(s)

Tabl

e O

f Con

tent

sGENERAL INFORMATION

Symbols .................................... iiiOrdering Parts ......................... iiiSerial Number Location .......... iiiSpecifications ........................... ivScheduled Maintenance .......... viWarranty Information............... vii

TROUBLESHOOTINGTroubleshooting Chart ............ A-2

COMPONENTTESTING & ADJUSTMENTS

Doors / Drawer:Door Adjustment ...................... B-2Drawer Removal ...................... B-3

Linear Scale:Checking Arm Alignment ......... B-4Arm Adjustment ....................... B-4

Digital Scale:Verifying Scale Accuracy ........ B-5Calibration Procedure .............. B-6Gravity Correction Procedure.. B-7Display Mode ... ....................... B-8

ACCESS PROCEDURES(none required)

WIRING DIAGRAMS(none required)

EXPLODED VIEWS / PARTS LISTSPictorial Index ......................E-2Upholstered Top ...................E-3Upperwrap Components .....E-4Linear Scale ..........................E-5Digital Scale..........................E-6Cabinet Assembly ................E-7Doors & Drawer ...................E-8Door / Drawer

Lock Components .............E-9

Sec

tion

ES

ectio

n C

Sec

tion

DGen

eral

Info

rmat

ion

Sec

tion

AS

ectio

n B

iii© Midmark Corporation 2007 SF-1918

General Information

Symbols

In Section A, test the components in the order indicated.(ex. 1st then, 2nd )

Refer to Section B for component testing procedures.

The symbols below may be used in this manual to representthe operational status of table functions and components.

Indicates the function / component is working properly.No action required.

Indicates the function / component is working,but a problem exists.

Indicates the function / component is not working at all.

Ordering Parts

The following information is required when ordering parts:• Serial number & model number• Part number for desired part.

[Refer to Exploded Views / Parts Lists section]

Non-warranty parts orders may be faxed to Midmark usingthe Fax Order Form in the back of this manual.

For warranty parts orders, call Midmark's Technical ServiceDepartment with the required information.Hours: 8:00 am until 5:00 pm EST [Monday - Friday]Phone: 1-(800)-Midmark

Serial Number Location

Gen

eral

Info

rmat

ion

Equipment AlertIndicates a potentially hazardous situation

which could result in equipment damage if not avoided.

DANGERIndicates an imminently hazardous situation which

will result in serious or fatal injury if not avoided. Thissymbol is used only in the most extreme conditions.

WARNINGIndicates a potentially hazardous situation which

could result in serious injury if not avoided.

CAUTIONIndicates a potentially hazardous situation which may

result in minor or moderate injury if not avoided. It may also beused to alert against unsafe practices.

ON/ZERO

OFF

kg/lb

kg

lb

BWB-800A CLASS III

200 kg/0.1kg 4

00lb/02lb nmax 2.20

CENTER

LOAD

TANI TA

MA779300i

Midmark

Digital ScaleModel / Serial

Number Location

640 TableModel / Serial

Number Location

Rev 10/8/12

iv© Midmark Corporation 2007 SF-1918

General Information

35.75 in.(97.2 cm)

18.0 in.(45.7 cm)

MA777700i

51.25 in. (130 cm)

41.875 in.(106.4 cm)

35.75 in.(90.8 cm)

20.75 in.(52.7 cm)

ON/ZERO

OFF

kg/lb

kg

lb

BWB-800A CLASS III

200 kg/0.1kg 4

00lb/02lb nmax 2.20

CENTER

LOAD

TANI TA

SpecificationsMaximum Patient Weight: ....................... 40 lbs (18 kg)Paper Roll (maximum size): ................... 14 in. long x 3 in. diameter 35.6 cm x 7.6 cm)Weight of Table: ........................................ 170 lbs (77 kg)

Digital ScaleAccuracy:Patients 0 to 22 lbs (0 to 10 kg) ................ +1 oz (+28 g)Patients 22 to 40 lbs (10 to 18 kg) ............ +2 oz (+56 g)Minimum Increments: ............................. 1 oz (0.01 kg)Type Measurement: ................................ Electrical Resistance MethodPower Source:Batteries .................................................... six (6) AA (LR6 Alkali)AC Adapter ................................................ Input: 120 VAC, 60 Hz, 5W Output: 9 VDC, 200mAPower Consumption: ............................... 0.25 Watts max.Display: .................................................... LCD w/ 1 in (25 mm) numerals

Linear Scale (Measuring Arm)Accuracy: ................................................. +1/8 in. (+3 mm)Minimum Increments .............................. 1/8 in. (0.5 cm)

Digital Scale

Linear Scale

v© Midmark Corporation 2007 SF-1918

General Information

Scheduled Maintenance Chart

Interval Inspection or Service

Service, Adjust, Repair

and/or Replace as Required

Clean upholstery with diluted bleach solution.

Ratio - 10:1 (water:bleach)

Wipe painted metal & plastic surfaces with a

clean soft cloth and mild cleaner.

(NOTE: Periodic application of common

furniture wax will ease cleaning, and maintain

the luster of the surfaces).

Obvious Damage

Visually inspect components for damage that

could cause problems during operation or

unsafe operation.

WeeklyCheck accuracy of digital

scale

Refer to: Digital Scale - Verifying Scale

Accuracy (later in this manual)

Every two monthsCheck measuring arm

alignment

Refer to: Measuring Arm Alignment

(later in this manual)

Mechanical OperationCheck all mechanical functions for proper

operation.

Verify Table is Level

Place a level on table top. Adjust if necessary.

Refer to: Leveling the Table (later in this

manual).

Labels / Decals Replace any missing or illegible labels.

Lubricate Lubricate moving parts with light machine oil.

Hardware All fasteners must be present and fastened

securely.

Date of Service: _____/____/____

Location:

Service Technician:

Scheduled Maintenance

640 Pediatric Examination Table

Daily

Cleaning

Semi-Annually

Rev 10/8/12

vi© Midmark Corporation 2007 SF-1918

General Information

Warranty Information

SCOPE OF WARRANTYMidmark Corporation (“Midmark”) warrants to the original purchaser its new Alternate Careproducts and components (except for components not warranted under “Exclusions”)manufactured by Midmark to be free from defects in material and workmanship undernormal use and service. Midmark’s obligation under this warranty is limited to the repair orreplacement, at Midmark’s option, of the parts or the products the defects of which arereported to Midmark within the applicable warranty period and which, upon examination byMidmark, prove to be defective.

APPLICABLE WARRANTY PERIODThe applicable warranty period, measured from the date of delivery to the original user, shallbe one (1) year for all warranted products and components.

EXCLUSIONSThis warranty does not cover and Midmark shall not be liable for the following: (1) repairs andreplacements because of misuse, abuse, negligence, alteration, accident, freight damage, ortampering; (2) products which are not installed, used, and properly cleaned as required in theMidmark “Installation” and or “Installation / Operation Manual for this applicable product. (3)products considered to be of a consumable nature; (4) accessories or parts not manufacturedby Midmark; (5) charges by anyone for adjustments, repairs, replacement parts, installation, orother work performed upon or in connection with such products which is not expresslyauthorized in writing in advance by Midmark.

EXCLUSIVE REMEDYMidmark’s only obligation under this warranty is the repair or replacement of defective parts.Midmark shall not be liable for any direct, special, indirect, incidental, exemplary, orconsequential damages or delay, including, but not limited to, damages for loss of profits orlossof use.

NO AUTHORIZATIONNo person or firm is authorized to create for Midmark any other obligation or liability inconnection with the products.

THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHERWARRANTIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIESOF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESSFOR ANY PARTICULAR PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR ORREPLACEMENT OF DEFECTIVE PARTS.

SF-1487 REV. A1

Additional InformationFailure to follow the guidelines listed below will void thewarranty and/or render the table unsafe for use.

• If a malfunction is detected, do not use the table untilnecessary repairs are made.

• Do not attempt to disassemble table, replacecomponents, or perform adjustments unless you area Midmark authorized service technician.

• Do not use another manufacturer's parts to replacemalfunctioning components. Use only Midmarkreplacement parts

© Midmark Corporation 2007 SF-1918A-1

Troubleshooting

Models:Serial Numbers:

Sec

tion

ATroubleshooting Troubleshooting Page

Troubleshooting Chart ........................... A-2

© Midmark Corporation 2007 SF-1918A-2

Troubleshooting


Problem Probable Cause Check / Test Correction

(If applicable) Batteries are low. Replace batteries, or use AC adapter.Replace old batteries with six

new AA batteries

Digital display acts erratically.Mode setting has been lost due to a power

surge or replacement of digital display.Check mode setting.

Adjust mode setting to: H8830 (Refer to

Section B: Digital Scale -

Display Mode Setting)

Paper roll interfering with table top.Check to see if paper roll is in

contact with table top. Reduce the diameter of the paper roll, or

remove paper roll completely.

Table is located where excessive vibration occurs.

Check for signs of vibration at table location.

Move table to another location.

Digital scale out of calibration.Refer to Section B: Digital Scale -

Verifying Scale Accuracy.

Calibrate digital scale. (Refer to Section B: Digital Scale -

Calibration Procedure)

Diital display or scale platform malfunctioning.

-Replace display* / platform*

as necessary.

Scale label is not positioned properly.Measure from end of table top

to scale label.Reposition label if necessary.

Measuring arm out of adjustment.Refer to Section B: Linear Scale -

Checking Arm Alignment.Adjust arm as necessary.

Replace digital display*. Digital display is malfunctioning. -

Replace scale platform*. Scale platform is malfunctioning. -

Secure connections. If necessary, replace display harness*.

Display harness loose or damaged. (The display harness connects the digital

display to the scale platform)

Check display harness connections.Digital display works, but

measured weight stays at zero with weight on table.

Nothing is appears on display when the ON / ZERO button is

pressed.

Table is not level. Place level on table top.

Linear scale is inaccurate.

(If applicable) AC adapter is disconnected or malfunctioning.

Secure connections. If necessary, replace AC adapter*.

Check AC adapter connections at the display and at the wall outlet.

Adjust leveling feet as necessary.

Measured weight is inaccurate.

Display harness loose or damaged. (The display harness connects the digital

display to the scale platform)

Check display harness connections.Secure connections.

If necessary, replace display harness*.

Troubleshooting Chart

Troubleshooting Chart* Only the complete digital scale assembly is available thru Midmark.For digital scale components, contact TANITA Corporation @ 847-640-9241.

© Midmark Corporation 2007 SF-1918

Component Testing & Repair

B-1Models:

Serial Numbers:

ComponentTesting & Repair

Sec

tion

BComponents PageDoors / Drawer:

Door Adjustment ................................ B-2

Drawer Removal ................................ B-3

Linear Scale:

Checking Arm Alignment ................... B-4

Arm Adjustment ................................. B-4

Digital Scale:

Verifying Scale Accuracy ................... B-5

Calibration Procedure ......................... B-6

Gravity Correction Procedure ............. B-7

Display Mode Setting ......................... B-8

www.Documark.com: File Name

Digital Scale Replacement* ........003-1836-00

Upholstered Top

Replacement* .........................003-1811-00

003-1836-00.pdf

003-1811-00.pdf



B-2Models:

Serial Numbers:

Doors / Drawer

Door Adjustment

Doors / Drawer ALL

Doors / Drawer Page

Door Adjustment ................................... B-2

Drawer Removal .................................... B-3

Exploded View / Part Numbers ............. E-8

MA777600i

Depth AdjustmentTurn this screw to movepanel forward / back.

Horizontal AdjustmentTurn this screw to movepanel side to side.

Vertical AdjustmentLoosen this screw on both hinges.Move door up / down, then tighten screws.



B-3Models:

Serial Numbers:

MA779500i

Doors / Drawer

Drawer Removal / Installation

Doors / DrawerALL

To remove drawer...A. Spread sides of drawer drawer outward as shown to release from slide tabs.B. Pivot drawer upward, then pull out to remove.

To install drawer...A. Place drawer on slides & push forward until it hits the stop tabs.B. Push drawer down until it snaps onto slide tabs.

Stop Tab

Slide Tab



B-4Models:

Serial Numbers:

Linear Scale

Checking / Adjusting Arm Alignment

Linear Scale ALL

ON/ZERO

OFF

kg/lb

kg

lb

BWB-800A CLASS III

200 kg/0.1kg 4

00lb/02lb nmax 2.20

CENTER

LOAD

TANI TA

MA777500i

Measuring Arm

Setscrew

To check measuring arm alignment...A. Pivot measuring arm out as shown.B. Using a carpenter’s square, check to see if the measuring arm is square with the back of the table top.C. If necessary, adjust arm until square.

To adjust measuring arm...Using a 3/32” allen wrench, adjustsetscrew in / out until measuring armis square with the back of the table top.

Linear Scale Page

Checking / Adjusting Arm Alignment ..... B-2




B-5Models:

Serial Numbers:

Digital Scale

Verifying Scale Accuracy

Digital ScaleALL

MA777400iMA777000i

ON / ZERO

lb • oz / kg

CENTER ZERO

Step 2: Press lb • oz / kg button to select unit of measure.

Display: Arrow appears beside selected unit (lb • oz / kg).

Step 1: Press ON / ZERO button.

Display: Flashes “8.8.8.8.8”, then shows “0.0”Arrow appears beside CENTER ZERO (indicates scale is zeroed and ready for use).

Step 3: Place a 25 lb (11.3 kg) calibrated testweight in the center of the table top.

Step 4: The weight displayed shouldmatch the calibrated test weight.

Note: Allowable tolerance*: + 2 oz (56 g)

Digital Scale PageVerifying Scale Accuracy ...................... B-5

Calibration Procedure ............................ B-6

Gravity Correction Procedure ................ B-7

Display Mode Setting ............................ B-8



Digital Scale Replacement* .......003-1836-00

* Replacement instructions are provided with this part. They are alsoavailable on Documark.com, or by clicking on the link in the blue box.

WARNINGIf scale reading is out of tolerance...

Perform Calibration Procedure. If necessary, replacedigital scale assembly*

Do not use scale until problem has been rectified.

Rev 10/10/12

003-1836-00.pdf



B-6Models:

Serial Numbers:

ON / ZERO

lb • oz / kg

Digital Scale - continued

Calibration Procedure

The Calibration Procedure must be performed when any of the following conditions occur:• Scale readings appear to be inaccurate.• The digital display, or any other scale component is repaired or replaced.• Annually, as part of a scheduled maintenance plan.• The table is moved (geographically) to a new location with a

significantly different elevation level.

Digital Scale

Calibration Procedure - continued: Display shows:

Step 5: Gently place 50 lb. of calibratedweight on the center of the table top.

Allow weight to stablize for 10 seconds,then press the lb • oz / kg button. ' F 1 '

Step 6: Remove weights from table.Press OFF button.

Step 7: Verify scale accuracy by performingthe procedure on the previous page.

Step 8: Perform "Gravity Correction Procedure"on following page.

Calibration Procedure: Display shows:

Step 1: While pressing the lb • oz / kg ' 88888 'button, press & release theON / ZERO button to turn displaypower ON.

Release lb • oz / kg button when ' F 1 ''F 1' appears on display.

Step 2: Press the ON / ZERO button. ' F 2 '

Step 3: Press the lb • oz / kg button. either ' 9 ' or ' 16 '

Step 4: If the display shows ' 16 ', initially: ' 0'press the lb • oz / kg button. will change to: ' 2 '

If the display shows ' 9 ',press the ON / ZERO button, initially: ' 0'then press the lb • oz / kg button. will change to: ' 2 '

Once display changes to ' 2 ',go to Step 5.



B-7Models:

Serial Numbers:


Gravity Correction Procedure

The Gravity Correction Procedure must be performed when any of the following conditions occur:• Whenever the scale is calibrated.• The table is moved (geographically) to a new location with a

significantly different elevation level.

Gravity Correction Procedure: Display shows:



Step 2: Press the ON / ZERO button untildisplay shows 'F 3' . ' F 3 '

Step 3: Press the lb • oz / kg button. ' 0.00'

Step 4: Adjust the gravitational compensation ' 0.0x 'value to 0.00. adjust if necessary(Press ON / ZERO button to increase) to show:(Press OFF button to decrease) ' 0.00 '

Step 5: Press the lb • oz / kg button. ' F 1'

Step 6: Press the OFF button.

ON / ZERO

lb • oz / kg

OFF



B-8Models:

Serial Numbers:

ON / ZERO

lb • oz / kg

OFF


Display Mode Setting

The Display Mode Setting Procedure must be performed when anyof the following conditions occur:

• The digital display unit is replaced.• The PC board inside the digital display unit is replaced.

Digital Scale

Display Mode Setting Procedure: Display shows:




Step 3: Press the lb • oz / kg button.(The mode setting should be 'H8830'. ' H 'If an initial mode setting has not beenperformed, only 'H' will be displayed.

Step 4: Press the ON / ZERO button to ' Hxx 'change the first digit to ' 8 '. toThen pressthe OFF button to changethe second digit to ' 8 '. ' H88 '

Display Mode Setting Procedure: Display shows:

Step 5: Press the lb • oz / kg button. ' F 1 '


Step 7: Press the ON / ZERO button to ' H88xx 'change the third digit to ' 3 '. toThen pressthe OFF button to changethe fourth digit to ' 0 '. H8830 '

Step 8: Press the lb • oz / kg button. ' F 1 '

Step 9: Press the OFF button to turnto turn digital display off.

Exploded Views &Parts Lists

Sec

tion

E

E-1© Midmark Corporation 2007 SF-1918

Description Page

Pictorial Index .............................E-2

Upholstered Top ............................E-3

Upperwrap Components ................E-4

Linear Scale ..................................E-5

Digital Scale ..................................E-6

Cabinet Assembly .........................E-7

Doors & Drawer .............................E-8

Door / Drawer Lock Components ...E-9

Always Specify Model & Serial Number



E-2

640

ON/ZERO

OFF

kg/lb

kg

lb

BWB-800A CLASS III

200 kg/0.1kg 4

00lb/02lb nmax 2.20

CENTER

LOAD

TANI TA

MA779100i

Digital Scale ................ E-6

includes:mounting bracket & hardware

Upholstered Top ................ E-3

includes:linear scale pad & measuring label

Cabinet Assembly ......... E-7

includes:cabinet shelf & shelf clips

Linear Scale................. E-5

Doors & Drawer ............. E-8

includes:color inserts, hinges, & slides

UpperwrapComponents .................... E-4

* Indicates multiple pages due to a serial number break for the parts illustration

OptionalDoor / DrawerLock Components ......... E-9




1

2

3

4

7

5

6

Item Description Qty.

1 Upholstery Kit (incl. items 2 & 3):a) Standard ................................................. 1b) Cal. 133 .................................................. 1

2 • Linear Scale Pada) Standard .............................................. 1b) Cal. 133 ................................................ 1

3 • Linear Scale Label .................................... 14 Paper Tear Strap ......................................... 15 Refer to: "Digital Scale" ........................... Ref6 Refer to: "Linear Scale" ........................... Ref7 Screw (1/4-20 x 1") ..................................... 4

a) 002-1109-00-xxxb) 002-1109-01-xxx

MA778500i

a) 028-0263-xxxb) 028-0738-xxx

029-0017-10

040-0250-89

061-0273-00

Upholstered TopAllE-3


Refer To: PageLinear Scale ........................................... E-5

Digital Scale ........................................... E-6

Upholstered Top

Replacement* ....................... 003-1811-00

Color Selector ................ www.midmark.com

ATTENTION: Refer to Current Color Optionslink for appropriate numbers to replace -xxx.

Rev. 4/08

003-1811-00.pdf

http://www.midmark.com/assets/swf/ColorSelectors/Medical_Color_Selector/c0490st.swf





1 Upperwrap ................................................... 12 Midmark Nameplate .................................... 13 Paper Roll Cover ......................................... 14 Washer ......................................................... 15 Nut ................................................................ 16 Screw (#10-24 x 1/2") ................................. 17 Pop Rivet ..................................................... 88 Screw (#10-24 x 3/8") ................................. 1

MA779000i

1

2

3

4

5

6

7

8030-1721-xx-xxx

061-0860-01

050-7129-00-216

045-0001-134

041-0010-02

040-0010-12

042-0010-04

040-0010-109

UpperwrapComponents

AllE-4

Rev. 2/08




1

2

3

6

7

8

9

10

11

12

13

14

15

4

5

3


1 Screw (#10-24 x 5/8") ................................. 22 Measuring Arm Weldment ........................... 13 Refer to: "Upholstered Top" .................... Ref4 Pivot Washer ............................................... 15 Spring Washer ............................................. 16 Setscrew ...................................................... 17 Linear Slide Assembly ................................. 18 Screw (#8 x 3/4") ......................................... 99 Pivot Bracket ............................................... 1

10 Pop Rivet ..................................................... 411 Slide Cover .................................................. 112 Screw (3/4") ................................................. 413 Flange Bearing ............................................. 114 Snap Ring .................................................... 115 Arrow Label .................................................. 1

Linear Scale(Measuring Arm)

MA778600i

E-5All

040-0010-56

030-1056-00-216

053-0383-00

045-0001-109

040-0010-63

016-0398-00

040-0008-46

030-0715-00-216

042-0010-04

050-7153-00-216

040-0008-46

053-0114-03

042-0077-00

061-0275-00

Refer To: Page

Upholstered Top ............................. E-2

Rev. 1/13




1

11

12

14

15

ON/ZERO

OFF

kg/lb

kg

lb

BWB-800A CLASS III

200 kg/0.1kg 400lb/02lb nmax 2.20

CENTER

LOAD

TANI TA

16

13

18

17

3

4

5

1

810

12

6

7

9

2

Digital Scale


1 Tanita Digital Scale Assembly (incl. item 2)Tanita model: BWB-800TS(for individual parts, contact:Tanita Tech. Service @ 847-640-9241) .. 1

2 • AC Adapter ................................................ 13 Mounting Plate ............................................. 14 Screw (M4 x 8 mm ) .................................... 45 Nut ................................................................ 46 Cable Clamp ................................................ 17 Screw (#8-32 x 5/8") ................................... 18 Scale Mount Weldment ................................ 29 Nut ................................................................ 4

10 Nut ................................................................ 411 Screw (1/4-20 x 3/4") .................................. 412 Snap Bushing ............................................... 213 Cable Clamp ................................................ 314 Screw (#6-20 x 1 1/4") ................................ 215 Digital Scale Display Bracket ...................... 116 Spacer .......................................................... 217 Screw (#10-24 x 5/8") ................................. 418 Scale Washer .............................................. 4

MA778700i

E-6All

030-1744-00-216

050-5652-00

050-5022-00-216

042-0112-01

041-0026-02

030-1723-00-216041-0312-05

040-0008-48

015-0014-02

040-0250-84

053-0068-10

118167

040-0006-100

040-0010-12

041-0010-04

053-0110-14

002-1118-00


Digital Scale

Replacement* .........................003-1836-00


Rev. 1/09

016-0892-02

003-1836-00.pdf



© Midmark Corporation 2007 SF-1918E-7

All

3

3

2

5 3

4

3

6

7

1


1 Cabinet Assembly [includes screws (item 3) & nutserts] ....... 1

2 Bottom Support Bracket .............................. 23 Screw (#10-24 x 3/8") ............................... 124 Cabinet Bottom ............................................ 15 Leveling Foot ............................................... 46 Cabinet Shelf ................................................ 17 Shelf Clip ...................................................... 4

MA778900i

050-6469-00-216

016-0001-00

050-7111-xx-216

050-7372-00-216

053-0668-00

040-0010-109

029-4136-00

CabinetAssembly




4

5

6

10

9

11

5

3

2

1

7

8

12

13

E-8All


1 Clear Handle Cover (doors) ....................... 22 Colored Handle Insert (doors) .................... 23 Screw (#10-24 x 5/8") ................................. 44 Door Assembly (RH shown)

(incl. items 5 & 6) ...................................... 25 • Bumper ...................................................... 26 • Hinge (incl. screws) .................................. 27 Clear Handle Cover (drawer) ..................... 18 Colored Handle Insert (drawer) .................. 19 Drawer Slide (LH) ........................................ 1

10 Drawer Assembly (includes item 5) ............ 111 Drawer Slide (RH) ....................................... 112 Drawer Divider ............................................. 113 Drawer Divider ............................................. 1

MA778800i

053-1574-03

053-1591-02-xxx

040-0010-157

016-0510-00

053-0716-00

053-1574-07016-0513-00

029-3680-12

016-0513-01

LH: 029-4434-01-xxxRH: 029-4434-00-xxx

053-1591-06-xxx

Doors & Drawer

ATTENTION: For components of the door or drawer locking mechanism,refer to Door / Drawer Lock Components on the following page.

Refer To: Page

Door / Drawer Lock Components ....E-9

Rev. 10/11

053-0693-00-216

053-0682-00-216




AllE-9

Door / DrawerLock Components

8

9

4

5

7

8

68

3

2

1


1 Screw (10-24 x 3/8") ................................... 42 Lock Mullion ................................................. 13 Strike Plate ................................................... 14 Lock Plug ..................................................... 15 Lock Bezel ................................................... 16 Door Plate .................................................... 17 Lock Cylinder ............................................... 18 Screw (#6 x 5/8") ......................................... 79 Drawer Lock Bracket .................................. 1

MA7816i

040-0010-109

050-7122-00-216

016-0639-00

016-0567-05

016-0564-00

050-0366-00

016-0645-00

040-0006-63

050-3977-00

COMMENTSThe Technical Publications Department of Midmark Corporation takes pride in its manuals. We are sure that our manuals will fill all your needs when you are perform-ing scheduled maintenance, servicing, or repairs on a Midmark product. However, if you find any errors or feel there should be a change, addition, or deletion to themanuals, please let us know. We will correct any errors that we are made aware of and we will review requests for changes, additions, or deletions to the manuals andincorporate those requests deemed appropriate. If you see something in one of our manuals that you like or dislike, please let us know. Also, if there is something youfeel we could do to produce a better manual, please let us know.

If an error is found, please list the page and paragraph/figure in which the error was found along with a brief description of what the error is. If the correction to the erroris known, please include that information also. If a change, addition, or deletion is being requested, please list the page and paragraph/figure needing the change, alongwith a brief description of how you feel the paragraph/figure should be changed.

Please fax or mail a copy of this completed comment sheet to:

Page Number Paragraph/Figure Description

Midmark CorporationATTN: Technical Publications Dept.60 Vista DriveVersailles, Ohio 45380Fax: (937) 526-5542

SERVICE PARTS FAX ORDERING FORM(Do not tear out this page. Photo copy this page for use only.)

IMPORTANT NOTES:

1) Use this form for all non-warrantyorders only. Warranty orders mustbe telephoned in (1-800-643-6275).

2) FAX number to send order to:877-249-1793

3) All emergency orders must bereceived @ Midmark by 1:00 pm EST.

4) All underlined headings should befilled in prior to submittal.

AT

TE

NT

ION

: C

US

TOM

ER

SE

RV

ICE

DE

PAR

TM

EN

T

AD

DIT

ION

AL

CO

MM

EN

TS

:

NAME: SHIP TO:

ADDRESS:

CITY: STATE: ZIP:

CONTACT:

PHONE:

FAX #:

MODEL #: SERIAL #: SALES ORDER # (if applicable)

LINE # PART NUMBER QTY. DESCRIPTION COLOR(if applicable)

CREDIT CARD INFORMATION

CARD TYPE __________________________ _ CARD #_________-_________-_________-_________ EXP. DATE ______ / ______ / ________

NAME ON CARD ___________________________________________ SIGNATURE_______________________________________________________

DATE: / / TIME:

METHOD OF SHIPMENT:

PRIORITY: NON-EMERGENCY ORDER {to shipwithin 72 hours if part(s) are in stock.}

EMERGENCY ORDER {to ship within24 hours if part(s) are in stock.}[see note 3]

DEALER P.O. #:

ACCOUNT #:

ampm

Midmark Corporation60 Vista DriveP.O. Box 286Versailles, OH 45380-0286937-526-3662Fax 937-526-5542

www.midmark.com

Pediatric Examination Tabel

Documents