Patented Adjustable Dies Manual and CNC Automatic operated from VLM
Patented
Adjustable Dies
Manual and CNC Automatic operated
from VLM
VLM CNC Adjustable
Mechanical Parts
Advantages VLMEN CNC adjustable systems:
Automatic adjustable in steps of 10 mm.
Optional: in steps of 5 mm.
V-Opening standard V= 120 – 300 mm
Optional: with additional insert die VLME-B from V= 10 – 115 mm.
Digital input of the V – opening over separate display unit
Optional: input over the press brake display.
Short changeover times. V – 120 to V- 300 mm less as 20 seconds.
Compact and robustly build with VLM patented adjustability system.
Easy and cost effective maintenance of parts.
Induction hardened 62 HRC and easily changeable bending axes.
Installation on new and also on existing press brakes.
VLMEN automatic CNC adjustable dies
VLM semi-NC automatic version.
NEW
Adjustability concept
Version 1
Closing and opening of the die parts by electro motor,
V-opening and spacer bar movement by hand wheel.
Version 2
Closing and opening of the die parts by electro motor,
V-opening by hand wheel and spacer bar movement with pneumatic cylinder.
Version 3
NC controlled
Closing and opening of the die parts by electro motor,
V-opening by electro motor and spacer bar movement with pneumatic cylinder.
1
2
3
VLMDN SEMI - NC Adjustable
Mechanical Parts
VLM Standard Models
Model: VLMBN
W : 25 – 125 mm
R : 8 mm
Max. Load: 90° 125 t/m
Operating angle: from 30° – 180°
Die length: 250, 500, 550, 1000 and 1050 mm
VLMBN Assembly
Part list VLMBN
Number of parts is depending on the required length.
1 VLMBN 1R-1L
2 VLMBN 2
3 VLMBN 3
4 VLMBN 4
5 VLMBN SA
6 VLMBN nut
7 VLMBN ZA
8 VLMBN SS
9 VLMBN Bottom holder
10 VLMBN Spacer bar
An example of adjusting the VLMBN dies.
Fig.1
First, the securing screws (8) must be loosened until the required spacer bar
width .
Then, the front die halves (yellow arrows) are pushed backward so that the
spacer bars are freely accessible.
The spacer bars (10) can then be removed and replaced by the desired spacer
bars.
Fig. 2
The rear die halves (yellow arrows) are then pushed against the securing
screws so there is space for the required spacer bars.
Now the new spacer bar can be pushed in.
Fig. 3
The rear die halves have to be pushed against the rear spacer bars and there
after the securing screws have to tightened softly by hand.
Note:
When changing from a lager spacer bar opening to a smaller one, the die halves
must always be pushed against the spacer bar at each pushed-in length, so that
the spacer bars cannot become detached from each other.
Model: VLMDN
W : 65 – 185 mm
R : 12,5 mm
Max. Load: 90° 200 t/m
Operating angle: from 60° – 180°
Die length: 250, 500, 550, 1000 and 1050 mm
VLMDN Assembly
Part list VLMDN
Number of parts is depending on the required length.
1 VLMDN 1R-1L
2 VLMDN 2
3 VLMDN 3
4 VLMDN 4
5 VLMDN SA
6 VLMDN nut
7 VLMDN ZA
8 VLMDN SS
9 VLMDN Bottom holder
10 VLMDN Spacer bar
Model: VLMEN
W : 120 – 300 mm
R : 20 mm
Max. Load: 90° 400 t/m
Operating angle: from 60° – 180°
Die length: 600 mm
VLMEN Assembly
Part list VLMEN
Number of parts is depending on the required length.
1 VLMEN 1R-1L
2 VLMEN 2
3 VLMEN 3
4 VLMEN 4
5 VLMEN SA
6 VLMEN nut
7 VLMEN ZA
8 VLMEN SS
8a VLMEN SS insert
9 VLMEN bottom holder
10 VLMEN spacer bar
Model: VLMFN
W : 150 – 400 mm
R : 25 mm
Max. Load: 90° 600 t/m
Operating angle: from 60° – 180°
Die length: 600 mm
VLMFN Assembly
Part list VLMFN
Number of parts is depending on the required length.
1 VLMFN 1R-1L
2 VLMFN 2
3 VLMFN 3
4 VLMFN 4
5 VLMFN SA
6 VLMFN nut
7 VLMFN ZA
8 VLMF SS
8a VLMFN SS insert
9 VLMFN bottom holder
10 VLMFN spacer bar
VLM Different additional tools.
VLMDN (EN – FN)
Additional die holders:
When you want to bend with a V-opening smaller than
65 mm, you can use a die holder (6) to use your own dies.
To fixate this holder on the VLMDN die, there are special
fixating blocks (1-4).
For protecting the die against dust you can use dust
protection sheets (5) which can be placed very easily.
VLMDN (EN – FN)
Additional insert dies:
On customer request
It is possible to produce additional insert dies to create a
V-opening of V 10 to V 60 mm
Design is depending of needed max. loading.
VLMEN – FN Additional Insert Die
With this insert dies you can create additional V-Openings of
V= 10 – 115/ 145 mm.
The insert dies can be placed without any screwing.
1 Insert Die Part
2 ZA axe
3 Shackle A
4 Shackle B
5 Screw
Step 1
Place the insert dies on the back die parts.
Step 2
Place the insert dies on the front die parts.
The insert dies are ready for use.
VLME-B insert die measurements
VLME-B insert dies in use
VLMEN - FN special bottom holder
Die part movement in – out by hand screwdriver.
VLM can also offer special adjustable press brake
tooling on customers request.
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com
VLM bvba
Address: Geloeslaan 25, 3630 Maasmechelen, Belgium Phone: +32-(0)89-777255, Mobile : +32-(0)473-768406, Fax: +32-(0)89-777244 Email: [email protected], Website : www.vlmbvba.com