Parts Manual for 21 STEEL DECK WALK BEHIND MOWER SERIES 7 - BASCO

Parts Manual for

Revision 2,

21" STEEL DECK WALK BEHIND MOWERSERIES 7

COPYRIGHT © 2005

McDonough, GA, 30253 U.S.A.

TP 400-5143-2-WB-N12/19/2005Manual No. 7006051A

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

PUSH MODELS PROPELLED MODELS

21357B DP21357B21407T DP21407T

21407T-2 DP21407T-221507B DP21507B21507T DP21507BE

G23157B GP21507BM21357B GP21507BER21357B MP21357BR21407T MP21507BER21507B OP21407T-2R21507TV OP21507B

P21357BP21407R-2P21407T

P21407T-2P21507B

P21507BEP21507TVPD21357BRP21357BRP21407TRP21507B

RP21507BERP21507TV

Table Of Contents

TP 400-5143-2-WB-NManual No. 7006051A21" STEEL DECK WALK BEHIND MOWER

SERIES 7 3

PAGE GROUP4 Handles & Controls8 Cutting Deck, Blade, Interlock

10 Front Wheel Bracket, Latches12 Rear Wheels, Brackets, Latches14 Front Wheels16 Rear Wheels18 Drive System - Self Propelled22 Transmission (Differential)24 Throttle Controls - Series 726 Decals (Part 1)28 Decals (Part 2)30 Side Chute, Adapter32 Accessory - Grass Bag34 Accessories - Recycling Kits36 Mulcherizer38 Accessory - Snapperizer40 Accessory - Thatcherizer42 Accessory - Electric Start

Handles & Controls

TP 400-5143-2-WB-NManual No. 7006051A 21" STEEL DECK WALK BEHIND MOWER

SERIES 74

Handles & Controls

Footnotes:


SERIES 7 5

Part No DescriptionItem Qty Note

1 7036354 HANDLE, Upper Used on Push7036357 HANDLE, Upper Used on Self-Propelled

2 7036350 HANDLE, Middle Used on All3 7046502 HANDLE, Lower Left Hand Was 38467, Used on All4 7035342 HANDLE, Lower Right Hand Was 38466, Used on All5 7017072 CONTROL, Blade Used on All6 7033904 CLIP, Blade Control Used on All (Same either side)7 7023820 CABLE, Blade Control, 47.94" Overall length B&S 3.5 H.P. Engine 1990 Model

7023835 CABLE, Blade Control, 63.87" Overall length TEC 2-cycle Engine 1990 Model7023765 CABLE, Blade Control, 52.65" Overall length B&S 5.0 H.P. Engine 1990 Model7016566 CABLE, Blade Control, 46.3" Overall lenght Used on Briggs (All Engines)

("91 Models & Later)7016708 CABLE, Blade Control, 56.93" Overall length Used on Tecumseh (Side Valve

Engines) ("91 Models & Later7016709 CABLE, Blade Control, 63.42" Overall length TEC 2 Cycle Engine 1991 &

Later7016425 CABLE, Blade Control, 57.0" Overall length Used on Tecumseh OHV Engine7017276 CABLE, Blade Control, 47.95" Overall length Used on Robin

8 7032826 HANDLE, Wheel Drive Used on Self-propelled9 7014307 GRIP, Wheel Drive Handle Used on Self-propelled

10 7023134 CABLE, Clutch Pull (Z-BEND) Used on Self-propelled11 7012121 COVER, Vinyl (Part of item 10)12 7012122 SPRING, Clutch Used on Self-propelled13 7038478 SECTOR, Speed Used on Self-propelled14 7023795 LEVER, Speed Control Used on Self-propelled15 7012093 SPRING, Speed Control Used on Self-propelled16 7090188 WASHER, 3/8" Flat Used on All-different locations17 7023801 GRIP, Speed Control Handle Used on Self-propelled18 7032830 ANCHOR, Speed Control Used on Self-propelled19 7032408 GUIDE, Lower V-Belt Used on Self-propelled20 7023790 ROD, Transfer Used on Self-propelled21 7010937 CLIP, Transfer Rod Used on Self-propelled22 7090895 TEE-NUT, 5/16-18 Used on Self-propelled23 7012114 BUSHING, Differential Used on Self-propelled24 7090595 BOLT, 5/16-18 x 3/4 Flange Lock Used on Self-propelled25 7090238 CAPSCREW, 5/16-24 x 1 Used on Self-propelled26 7090799 BOLT, 5/16-18 x 5/8 Carriage Was 91026 (Used on All

(different locations)27 7091601 NUT,5/16-18 Hex Flange Lock Was 90585 (Used on All

(different locations))28 7090222 NUT, 5/16-24 Center Lock Used on Self-propelled29 7023813 CLIP Cable/Wiring Used on All

Handles & Controls


SERIES 76

Handles & Controls

Footnotes:


SERIES 7 7


30 7091013 SCREW, 1/4-20 x 1-7/8 Curved Head Used on All31 7023735 4 KNOB, 5/16-18 Used on All32 7091025 CAPSCREW, 1/4-28 x 1-3/8 Used on Self-propelled33 7090053 LOCKWASHER, 1/4 Internal Tooth Was 91023 (Used on All

(different locations))34 7090095 NUT, 1/4-20 Hex Was 91024 (Used on All

(different locations)35 7091022 CAPSCREW, 1/4-28 x 1-3/4 Used on All (throttle control)36 7014343 BUSHING Used on All37 7023792 PIN, Clutch Handle Used on Self-propelled38 7091020 PUSH-NUT (for handle pin) Used on Self-propelled39 7023745 DECAL, Blade Control Used on All40 7023901 GRIP, Foam Used on Push

7022460 GRIP, Foam Was 23841, Used on Self-Propelled

41 7091077 BOLT, 5/16-18 x 5/8" Carriage Used on Self-Propelled

Cutting Deck, Blade, Interlock


SERIES 78

Cutting Deck, Blade, Interlock

Footnotes:


SERIES 7 9


1 7057663 DECK, Mower (Includes painted deck with decals)

2 7091601 12 NUT, 5/16-18 Hex Flange Lock Was 905853 7090731 9 BOLT, 5/16-18 x 1/2" Short Neck Carriage (Gr.)4 7091303 BOLT, 5/16-18 x 1" Short Neck Carriage Was 903835 7090324 2 SCREW, 3/8-16 x 1" Self-tapping (Engine Mounting)6 7032417 SPRING, Wheel Bracket Type Interlock7 7032416 BRACKET, Wheel Bracket Type Interlock8 7012048 INSULATOR, Interlock9 7091122 2 SCREW, 1/4-20 x 1/2" Self-tapping Was 90539

10 7090385 WASHER, #8 Tab Internal Tooth Lock11 7090379 SCREW, #8-18 x 3/4" Hex Head Machine12 7090167 SCREW, 3/8-24 x 2" Hex Head Cap (Gr. 5)13 7012063 WASHER, Cone14 7019795 BLADE, Cutter

7017168 BLADE, Cutter (For Recycling Models)15 7012927 HUB, Blade Drive (7/8" Dia. I.D.) (For '90 Models &. Earlier)

7015626 HUB, Blade Drive (25mm Dia. I.D.) (For '91 Models & Later)16 7010783 KEY, Hi-Pro (For '90 Models & Earlier)

7015894 2 KEY, Woodruff (Briggs)(Tecumseh 2 CY) (For '91 Models & Later)7016755 KEY, Square (Robin & Tecumseh) (For '91 Models & Later)

17 7090201 SCREW, 5/16-18 x 5/16" Hex Socket Set18 7021707 PULLEY, Engine (Briggs 3.5 H.P.) (7/8" I.D. x 1-7/8" O.D.) (For '90 Models & Earlier)

7015780 PULLEY, Engine (Briggs) (Tecumseh 2 CY) (25mm I.D. x 2-1/8" O.D.)

(For '91 Models & Later)

7022106 PULLEY, Engine (Tec. & Robin) (25mm I.D.x 2-1/8" O.D.) (For '91 Models & Later)19 7031968 SHIELD, Belt Opening Cover (For Push Models Only)20 7012135 BUSHING, Interlock Wire21 7060785 KIT, Air Lift (Includes items 22 thru 25); For

use with P/N 1-9795 Blade

22 7032558 2 LIFT, Air23 7090391 4 WASHER, 5/16 Internal Tooth Lock24 7091297 4 NUT, 5/16-24 Hex Was 9022325 7090228 4 SCREW, 5/16-24 x 11/16" Machine26 7011791 2 RETAINER, 5/16 Bolt27 7090799 2 BOLT, 5/16-18 x 5/8" Carriage

Front Wheel Bracket, Latches


SERIES 710

Front Wheel Bracket, Latches

Footnotes:


SERIES 7 11


1 7051885 ARM ASSEMBLY, Left Wheel (Consists of items 2, 3, 4, 5A,6)7051886 ARM ASSEMBLY, Right Wheel (Consists of items 2, 3, 4, 5B, 6)

2 7015761 BOLT, 5/16-18 Shoulder3 7012325 LATCH, Height4 7027702 GRIP, Latch

5A 7031016 ARM, Left Wheel5B 7031017 ARM, Right Wheel6 7011791 RETAINER, 5/16 Bolt7 7090391 WASHER, 5/16 Internal Tooth Lock8 7091511 NUT, 5/16-18 Hex Was 901969 7047971 BRACKET, Front Wheel

10 7021119 AXLE

Rear Wheels, Brackets, Latches


SERIES 712

Rear Wheels, Brackets, Latches

Footnotes:


SERIES 7 13


1 7046983 BEARING Was 187672 7091012 3 SCREW, #10-32 x 3/8" Self-Tapping3 7035717 LATCH, Height Adjusting Was 19218 (Self-Propelled

Models)4 7090731 BOLT, 5/16-18 x 1/2" Short Neck Carriage5 7091601 6 NUT, 5/16-18 Hex Flange Lock Was 905856 7052909 ASSEMBLY, Wheel Arm (Square Hole, Front Left & Rear Right) Was 51954 (Includes items

10,14,15,16,17)7 7052908 ASSEMBLY, Wheel Arm (Round Hole, Front Right & Rear Left) Was 51955 (Includes Items

11,14,15,16,17)8 7054246 WHEEL ARM ASSEMBLY (Rear Right "P" Models) Was 51814 Includes items

(1,2,3,12,14,15,16,17,25)9 7054247 WHEEL ARM ASSEMBLY (Rear Left "P" Models) Was 51815 Includes items

(1,2,3,13,14,15,16,17,25)10 7031016 ARM (Square Axle End)11 7031017 ARM (Round Axle End)12 7032722 ARM, Wheel Rear Right "P" Models13 7032723 ARM, Wheel Rear Left "P" Models14 7015761 BOLT, 5/16-18 x 1 Shoulder15 7011791 RETAINER, 5/16 Bolt16 7012325 LATCH, Height Adjusting (For Push Models)17 7027702 GRIP, Latch18 7036050 BRACKET, Right Rear Wheel (For Push Models)19 7036049 BRACKET, Left Rear Wheel (For Push Models)20 7036048 BRACKET, Right Rear Wheel (For Self-prop. "P" Models)21 7036242 BRACKET, Left Rear Wheel (For Self-prop. "P" Models)22 7021119 AXLE (For Rear on Push Models also

front on all)23 7011780 2 RING (For Push Models)24 7026166 GUARD, Rear Foot Was 37765 (Push Models)25 7091809 2 PIN, 1/8 x 1-1/2" Cotter Was 9029726 7019522 GUARD, Rear Foot (For Self-prop. "P" Models)27 7012616 SUPPORT, Foot Guard28 7091604 BOLT, 1/4-20 x 1/2 Short Neck Carriage Gr.5 Was 9000529 7090053 WASHER, 1/4 Int. Tooth Lock Was 9102330 7091576 NUT, 1/4-20 Hex Was 9006331 7023791 RING32 7090391 WASHER, 5/16 Int. Tooth Lock33 7091511 NUT, 5/16-18 Hex Was 90196

Front Wheels


SERIES 714

Front Wheels

Footnotes:


SERIES 7 15


1 7019195 WHEEL, 7 x 1.75 Plastic Rim Was 19333 (For "91 Models & Later)

7019195 WHEEL, 7 x 1.75 Plastic Rim (For "90 Models & Earlier)2 7019381 COVER, Wheel3 7090377 2 NUT, 7/16-20 Hex Center Lock4 7031960 CAP, Deep-Dish Hub5 7031961 WASHER, 7/16 Flat6 7012309 BUSHING, Axle

Rear Wheels


SERIES 716

Rear Wheels

Footnotes:


SERIES 7 17


1 7019420 WHEEL, 9 x 2.00 Plastic Rim Was 19334 (For Push Models) ('91 Models & Later)

7019420 WHEEL, 9 x 2.00 Plastic Rim Was 19196 (Push Models, 1990 Models & Earlier)

2 7022801 WHEEL, 9 x 2.00 Plastic Rim Was 19335 (For 3.5 H.P. Self-Propelled) ('91 Models & Later)

7019421 WHEEL, 9 x 2.00 Plastic Rim Was 19197 (For 3.5 H.P. 1990 Self-Propelled Models & Earlier)

3 7022801 WHEEL, 9 x 2.00 Steel Rim Was 19336 (Self-Propelled)("91 Models & Later)

7019201 WHEEL, 9 x 2.00 Steel Rim Was 19198 (Self-Propelled, 1990 Models & Earlier)

4 7019385 COVER, Wheel (For Push & w.5 H.P. Self-Propelled)

5 7019349 COVER, Wheel (For Self-Propelled)6 7090377 2 NUT, 5/16-18 Hex Center Lock7 7031960 CAP, Deep-Dish Hub8 7031961 WASHER, 7/16 Flat9 7012309 BUSHING, Axle (Push)

Drive System - Self Propelled


SERIES 718


Footnotes:


SERIES 7 19


1 7012354 BELT, Poly-Vee2 7034179 LINK, Differential Was 31880

7051921 ASSEMBLY, Clutch Idler (Includes items 3 thru 7)3 7032832 ARM, Clutch Idler4 7012124 PULLEY, Idler5 7090552 CAPSCREW, 1/4-28 x 1-3/8" Hex Head6 7090303 NUT, 1/4-28 Hex Lock7 7012117 2 BUSHING, 3/8 I.D. Nylon8 7072284 HEX-SHAFT Was 237449 7019383 PULLEY

10 7012316 WASHER11 7012126 SPRING, Torsion12 7012111 STUD13 7031873 HOLDER, Bearing (Inner Half)14 7028014 BEARING, Ball Was 1230415 7011025 O-RING16 7090289 NUT, 3/8 Hex Center Lock17 7031809 HOLDER, Bearing (Outer Half)18 7010937 CLIP, 1/4 Right Arc (Transfer Rod)19 7023790 ROD, Transfer20 7012353 BELT, Engine Drive

7053225 ASSEMBLY, Driven Disc Was 57444 (Includes 21 thru 28)21 7038486 PLATE, Thrust22 7010746 RING, Retaining23 7026693 BEARING, Ball Was 1547424 7090981 4 SCREW, #10-32 x 1/4" Self-Tapping Machine25 7061276 ASSEMBLY, Hub Was 51616 (Includes 11108

Bushing & 90913 Screws)26 7023364 DRIVEN-RING27 7031013 PLATE, Ring Retaining28 7090913 5 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx)29 7012125 GUIDE, Thrust Plate30 7090390 2 WASHER, 3/8 Internal Tooth Lock31 7090122 3 WASHER, 3/8" Flat32 7091630 3 NUT, 3/8-24 Hex Was 9015533 7091511 NUT, 5/16-18 Hex Was 9019634 7090187 WASHER, 5/16 Split Lock35 7090316 BOLT, 5/16-18 x 3/4 Carriage



SERIES 720


Footnotes:


SERIES 7 21


36 7032831 CONNECTOR, Transfer Rod37 ASSEMBLY, Drive-Disc38 BUSHING39 7029025 2 SPRING (Wheel Drive & Idler) Was 1732640 7032116 ARM, Idler41 7013847 RETAINER, 3/8 Bolt42 7090078 BOLT, 1/4-20 x 1-1/4" Carriage43 7090372 NUT, 1/4-20 Hex Center Lock

7050751 ASSEMBLY, Deck Bracket (Includes items 44 thru 46)44 7033774 BRACKET, Deck Was 31919 (Now 17696 +

33774)45 7012306 2 BUSHING, Flange46 7021758 SPACER47 7090534 SCREW, 5/16-18 x 1/2" Hex Head Cap48 7090391 WASHER, 5/16 Internal Tooth Lock49 7011079 WASHER, Spring50 7091597 COTTER-PIN, 3/32 x 1/2" Was 9055551 7091122 SCREW, 1/4-20 x 1/2" Self-Tapping Was 9053952 7090731 2 BOLT, 5/16-18 x 5/8" Short Neck Carriage53 7091601 2 NUT, 5/16-18 Hex Flange Lock Was 9058554 7012122 SPRING, Clutch55 7015752 LINK, Transfer Used on Electric Start models

only.56 7015753 JOINT, Ball Used on Electric Start models

only.57 7090095 NUT, 1/4-28 Hex Used on Electric Start models

only.

58 7091294 WASHER, 1/4 Flat Was 90055 (Used on Electric Start models only.)

59 7090053 WASHER, 1/4 Internal Tooth Lock Used on Electric Start models only.

Transmission (Differential)


SERIES 722

Transmission (Differential)

Footnotes:


SERIES 7 23


-- 7059070 ASSEMBLY, Transmission Was 57525 (Includes 1 thru 29)1 7092062 3 NUT, 5/16-24 Hex Lock, GR C Was 112012 7011132 WASHER, Spring3 7019213 PULLEY, Poly-Vee Belt4 7011724 WASHER, Spring5 7053942 HOUSING ASSEMBLY, Right Was 59794 (Includes 6 thru 10)6 7051908 HOUSING, Right Side Was 170807 7014155 3 SCREW, 5/16-24 x 1-1/8" Rib Neck8 7012314 2 SEAL, 5/8" ID9 7012507 2 BEARING, Differential

10 7073963 BEARING, Ball Was 1176711 7016544 PLUG, Housing Was 1113312 7050767 GEAR, Input13 7050830 AXLE, Short14 7012495 GEAR, Differential, 46 Tooth15 7031970 2 PLATE16 7031965 2 WASHER, Thrust17 7090557 4 SCREW, Cap, 10-32 x 1-1/2"18 7011774 GASKET, Housing19 7090189 WASHER, 5/16" Internal External Tooth Lock20 7051903 BRACKET, Differential21 7090911 4 SCREW, 1/4-20 x 1-1/4 Self-Tapping22 7012543 SPACER, Axle Gear23 7050831 AXLE, Long24 7021115 4 GEAR, Pinion, 12 Tooth25 7012500 4 SPACER, Pinion Gear26 7011110 4 SHAFT, Pinion27 7090376 4 LOCKNUT, 10-3228 7053939 HOUSING ASSEMBLY, Left Was 57523 (Includes 8, 9 & 29)29 7057634 HOUSING, Left Side Was 17015-- 7059070 ASSEMBLY, Transmission Was 57525

Throttle Controls - Series 7


SERIES 724

Throttle Controls - Series 7

Footnotes:


SERIES 7 25


7019254 Conduit Length, 45.0" - Briggs 4 Cycle For '90 Models & Earlier7023829 Conduit Length, 62.0" - Tecumseh 2 Cycle For '90 Models & Earlier7016565 Conduit Length, 58.0" - Briggs 4 Cycle For '91 Models & Earlier7016705 Conduit Length, 44.25" - Tecumseh 4 Cycle For '91 Models & Earlier7016706 Conduit Length, 62.0" - Tecumseh 2 Cycle For '91 Models & Earlier7016798 Conduit Length, 44.0" - Robin 2 Cycle For '91 Models & Earlier

Decals (Part 1)


SERIES 726

Decals (Part 1)

Footnotes:


SERIES 7 27


1 7013010 DECAL, Danger2 7023745 DECAL, Blade Control3 7023870 DECAL, Warning4 7044640 DECAL, SNAPPER Was 192795 7016191 DECAL, Warning & Starting

Decals (Part 2)


SERIES 728

Decals (Part 2)

Footnotes:


SERIES 7 29


1 DECAL, Housing Was 17300, no longer available2 DECAL, Housing Was 17303, no longer available3 DECAL, Housing Was 17298, no longer available4 DECAL, Housing Was 17297, no longer available5 DECAL, Housing Was 17305, no longer available6 DECAL, Housing Was 17295, no longer available7 DECAL, Housing Was 17302, no longer available8 DECAL, Housing Was 17306, no longer available9 DECAL, Recoil (3.85 O.D.) Was 17301, no longer available

10 DECAL, Recoil (3.35 O.D.) Was 17304, no longer available11 DECAL, Recoil (2.575 O.D.) Was 17294, no longer available

Side Chute, Adapter


SERIES 730

Side Chute, Adapter

Footnotes:


SERIES 7 31


1 7042965 KIT, Side Chute Was 60955 (10 per box of item 2)

2 7042965 CHUTE, Side Was 160903 7016050 ADAPTER, Grass Bag Deck4 7090951 3 NUT, 5/16-18 Hex Flange Lock5 7090188 WASHER, 5/16 Flat6 7023152 DEFLECTOR, Muffler7 7023023 3 SCREW, #8-18 x 3/8" Hex Head Cap8 7090316 BOLT, 5/16-18 x 3/4" Carriage Was 910979 7011791 RETAINER, 5/16 Bolt

10 7090122 WASHER, 5/16 Flat11 7029149 COVER, Deck Was 16111 (For Recycling

Models)

Accessory - Grass Bag


SERIES 732

Accessory - Grass Bag

Footnotes:


SERIES 7 33


7060935 KIT, Grass Bag Catcher (Incl. items 1 thru 4)1 7059322 ASSEMBLY, Grass Bag Was 51899 (Incl. items 2 and 3)2 7017069 BAG, Door Type (Charocoal)3 7051906 ASSEMBLY, Bag Wire4 7042489 CONNECTOR, Grass Bag Was 479695 7016050 ADAPTER, Bag

Accessories - Recycling Kits


SERIES 734

Accessories - Recycling Kits

Footnotes:


SERIES 7 35


-- 7061200 KIT, Recycling Cover Was 61030 (Includes items below)

-- 7061201 KIT, Recycling Plug Was 61032 (Includes items below)

1 7029149 COVER, 21" Deck Was 161112 7016814 PLUG, Chute Adapter3 7017168 BLADE, 21"

Mulcherizer


SERIES 736

Mulcherizer

Footnotes:


SERIES 7 37


-- KIT, Mulcherizer (Was 60842) Kit 60842 is no longer available, use either 7016814 Chute Plug or 7061200 Cover

7061200 KIT, Mulcherizer Was 60420 (Includes 1 thru 8)1 7019814 3 LINER2 7013870 HUB, 7/8" I.D.

7015936 HUB (25mm I.D.)3 7019521 BLADE, Mulcherizer4 7090483 SCREW, 3/8-24 x 1 3/4" Hex Head Cap (Gr.5)5 7012063 2 WASHER, Cone6 7090100 3 SCREW, 1/4-28 x 5/8" Hex Head Cap (Gr.5)7 7091294 6 WASHER, 1/4 Flat Was 900558 7090303 3 NUT, 1/4-28 Hex Lock

Accessory - Snapperizer


SERIES 738

Accessory - Snapperizer

Footnotes:


SERIES 7 39


7060440 KIT, Snapperizer (Includes items 1 thru 5)1 7051243 SCREEN, Fastener Assembly2 7039759 RING, Bottom3 7091297 3 NUT, 5/16-24 Hex Was 902234 7090187 3 WASHER, 5/16 Split Lock5 7012587 3 SPRING

Accessory - Thatcherizer


SERIES 740

Accessory - Thatcherizer

Footnotes:


SERIES 7 41


7061256 KIT, Thatcherizer Was 60476 (Includes 1 thru 27)1 7014113 2 LATCH, Frame Attachment

2A 7060965 BAR, Mount (Right Hand) Was 184972B 7018498 BAR Mount (Left Hand)3 7018499 2 ROD, Tine4 7018700 SUPPORT, Wheel5 7019948 TRAY, Tine6 7018496 6 SPRING, Tine Thatching Part of Hardware Bag P/N 6-

0574 (6 spring in bag)n7 7014100 BUSHING, Wheel Adj. Part of Hardware Bag P/N 6-

05558 7018493 AXLE, Wheel9 7018189 WHEEL, Gage 7 x 1.50

10 7091705 10 LOCKNUT, 1/4-20 Hex Was 90761 (Part of Hardware Bag P/N 6-0554)

11 7091098 4 WASHER, 1/4 SAE Was 90598 (Part of Hardware Bag P/N 6-0554)

12 7014114 2 SPRING, Compression13 7090825 2 BOLT, 1/4-20 x 1-1/4 Hex Part of Hardware Bag P/N 6-

055414 7091576 2 NUT, 1/4-20 Hex Was 90063 (Part of Hardware

Bag P/N 6-0554)15 7014111 2 CAP, Vinyl Part of Hardware Bag P/N 6-

0555

16 7090015 2 BOLT, 1/4-20 x 1-3/4 Carriage Part of Hardware Bag P/N 6-0554

17 7091303 6 BOLT, 5/16-18 x 1 Carriage Was 90383 (Part of Hardware Bag P/N 6-0554)

18 7091530 2 BOLT, 1/4-20 x 3/4 Carriage Was 90074 (Part of Hardware Bag P/N 6-0554)

19 7014098 6 WASHER, Reinforcing Part of Hardware Bag P/N 6-0554

20 7090187 6 LOCKWASHER, 5/16 Part of Hardware Bag P/N 6-0554

21 7091511 6 NUT, 5/16-18 Hex Was 90196 (Part of Hardware Bag P/N 6-0554)

22 7014101 2 PUSH NUT, 1/2 Part of Hardware Bag P/N 6-0555

23 7014342 4 BEARING, Nyliner Part of Hardware Bag P/N 6-0555

24 7014103 SETSCREW, 5/16 x 1/4 Part of Hardware Bag P/N 6-0555

25 7090250 2 WASHER, 1/2 Part of Hardware Bag P/N 6-0554

26 7014115 DECAL, Adjustment (Not Shown)27 7014062 DECAL, Thatcherizer (Not Shown)

Accessory - Electric Start


SERIES 742

Accessory - Electric Start

Footnotes:


SERIES 7 43


7067012 KIT, Battery (Includes items 1,2,3,& 4)1 7067012 BATTERY,12 Volt Was 197632 7015488 HARNESS, Battery3 7043977 2 SCREW, #10-24 x 1/2 Hex Head Cap4 7090932 2 NUT, #10-24 Square

7051910 ASSEMBLY, Switch/Bracket (Includes items 5 thru 10)5 7011167 KEY, (Set of 2)6 7015207 ASSEMBLY, Seal & Face Nut7 7038485 BRACKET, Ignition Switch8 7023894 COVER, Switch9 7015206 NUT, 3/4-20 Lock

10 7011139 SWITCH, Ignition Was 1520511 7090552 2 SCREW, 1/4-28 x 1 3/8" Hex Head Cap12 7090053 2 WASHER, 1/4 Internal Tooth Lock13 7090095 2 NUT, 1/4-28 Hex14 7019298 HARNESS, Wiring Was 17213 (For "91 Models &

Later)7019298 HARNESS, Wiring (For "90 Models & Earlier)

15 7032906 BRACKET, Battery (For Self-Propelled Models)16 7036132 COVER, Battery (For Self-Propelled Models)17 7090731 3 BOLT, 5/16-18 x 1/2" Carriage18 7091601 3 NUT, 5/16-18 Hex Flange Lock Was 9058519 7012652 CLIP, Wiring20 7061188 CHARGER, Battery (60 Hertz) Was 1883421 7090779 BOLT, 5/16-18 x 5/8" Short Neck. Carriage, Gr. 522 7011791 RETAINER, 5/16" Bolt

Parts Manual for

21" STEEL DECK WALK BEHIND MOWERSERIES 7

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

Revision 2,

COPYRIGHT © 2005

TP 400-5143-2-WB-N12/19/2005Manual No. 7006051A

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

McDonough, GA, 30253 U.S.A.

Parts Manual for 21 STEEL DECK WALK BEHIND MOWER SERIES 7 - BASCO

Documents