HBUD Series LED High Bay Important: Read all instructions prior to installation. User Manual Part Number: Dimensional Drawings Rev Date: V1.0 10/27/2017 Rev Date: V1.0 10/27/2017 HBUD-50K100W, HBUD-50K150W HBUD-50K200W, HBUD-50K300W HBUD Series LED High Bay User Manual Part Number: HBUD-50K100W, HBUD-50K150W, HBUD-50K200W, HBUD-50K300W HBUD-50K100W HBUD-50K150W HBUD-50K200W HBUD-50K300W 5.12in 130.16mm 6.05in 153.67mm 10.95in 278.13mm 8.69in 220.73mm 7.19in 182.63mm 6.00in 152.40mm 6.03in 153.26mm 10.95in 278.13mm 8.69in 220.73mm 7.19in 182.63mm 7.52in 191.13mm 6.03in 153.26mm 8.69in 220.73mm 10.95in 278.13mm 7.19in 182.63mm 6.35in 161.29mm 12.63in 320.91mm 12.64in 321.01mm 9.61in 244.09mm 7.95in 201.98mm
2
Embed
Part Number: HBUD-50K100W, HBUD-50K150W HBUD Series LED ... · 1. Insert Eye Bolt and Washer into threaded hole on back of fixture and tighten. Hang fixture Insert Eye Bolt and Washer
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
HBUD Series LED High BayImportant: Read all instructions prior to installation.
1. Insert Eye Bolt and Washer into threaded hole on back of fixture and tighten. Hang fixture by attaching Eye Bolt (Fig. 1) to an existing hook or carabiner.
2. Connect the fixture wires to the corresponding wires in the junction box (not included).
Black
White
Green
BlackL L
N N
GND GND
White
Green
Warning
Wiring Diagram
• This product should be installed by a fully certified electrician in accordance with local building and electrical codes.
• Due to risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
• Failure to properly support the fixture during installation may cause damage or injury, for which the manufacturer is not responsible. Ensure the light bracket/eye bolt is securely mounted and will support the weight of the fixture.
1. Secure mounting plates to fixture with provided 4 x 21mm allen screws using 4mm allen wrench (A). Attach U-Bracket to mounting plate with 2 x 27mm allen screws and nuts using 6mm allen wrench (B).
2. Position desired angle of U-Bracket and secure with 2 x 4mm allen screws (C).
3. Mount Fixture to surface.4. Connect wiring to power supply. Black to Line, White to
Neutral, and Green to Ground.5. Restore power to circuit to test function.
1. Remove power prior to installation.2. Motion sensor and compact J-Box come attached to mounting
plates. Position motion sensor and provided compact J-Box on opposite sides of the light.
3. Attach motion sensor to light using 2 x 21mm Allen Screws using 4mm allen wrench (A).
1. Turn fixture upside down.2. Line up 3 holes from PC Reflector
to 3 threaded holes on light. 3. Screw 3 phillips screws to secure
PC Reflector
MotionSensor
Compact J-Box
From LED
1-10VDimming
Wires From LED
Power Source
Threaded Holes for PC Reflector
Threaded Holes for PC Reflector
(B)
(C)(B)
(C)
(A)(A)
4. Attach compact J-Box to light using 2 x 21mm Allen Screws using 4mm allen wrench (B).
5. Make wiring connections according to diagram.
6. Connect to power source. Black to Line, White to Neutral, and Green to Ground.
7. Restore power to circuit to test motion sensing functionality. *Note: Refer to motion sensor manual for operation.