-
Owner's Manual
T ®
ACCESSORIES FOR MODEL NOS. 315.212100, 315.212110 &
315.243150
10 in. (254 mm) COMPOUND MITER SAW
Item No._924310_924350924352
Save this manual forfuture reference.
_, CAUTION: Read and followall Safety Rules and
OperatingInstructions before first use of
this product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USAVisit the
Craftsman web page: www.sears.com/craftsman
972000-60303-01
• SAFETY
• LOOSE PARTS
• INSTALLATION
• SERVICES
-
READ ALL INSTRUCTIONS
READ THESE INSTRUCTIONS AND THEINSTRUCTIONS FOR THE
315.212100,315.212110, and 315.243150 COMPOUNDMITER SAW THOROUGHLY
before usingaccessories.
KNOW YOUR POWER TOOL. Read the owner'smanual for the Compound
Miter Saw carefully.Learn the saw's applications and limitations as
wellas the specific potential hazards related to thistool.
KEEP THE WORK AREA CLEAN. Cluttered workareas and work benches
invite accidents. DO NOT
leave tools or pieces of wood on the saw while it isin
operation.
,&
• ALWAYS WEAR SAFETY GLASSES. Everydayeyeglasses have only
impact-resistant lenses; theyare NOT safety glasses.
• ALWAYS DISCONNECT SAW FROM POWERSUPPLY BEFORE MAKING
ADJUSTMENTS ORADDING ACCESSORIES. Make sure the switch isoff when
reconnecting to power supply.
• SAVE THESE INSTRUCTIONS. Refer to themfrequently and use to
instruct other users. If youloan someone this tool, loan them these
instruc-tions also.
Look for this symbol to point out important safety precautions.
It
means attention!!! Your safety is involved.
The following accessories are included with item no. 924310,
924350, and 924352:
• Work Clamp
• Dust Bag
• Table Extensions (2)
• Stop Block
• Small Wing Screw
• Clamp Bracket (2)
• Clamp Bracket Screws (2)• Owner's Manual
WORKCLAMP
DUSTBAG
/"SMALLWINGSCREW
STOPBLOCK
TABLE EXTENSIONS
CLAMPBRACKET
SCREW
Fig. 1
_, WARNING: The use of attachments or accessories not listed
might be hazardous.
2
-
,_
WARNING:Topreventaccidentalstartingthatcouldcausepossibleseriouspersonalinjury,assembleallpartstoyoursawcompletelybeforeconnectingit
to
powersupply.Sawshouldneverbeconnectedtopowersupplywhenyouareassemblingparts,makingadjustments,installingorremovingbladesoraccessories,orwhennotinuse.
WORK CLAMPSee Figure 2.
The work clamp provides greater control by clampingthe workpiece
to the fence. It also prevents theworkpiece from creeping toward
the saw blade. Thisis very helpful when cutting compound miters.
Toinstall the work clamp, place the shaft of the clamp ineither
hole in front of the miter table base. Rotate theknob on the clamp
to move it in or out as needed.
,_ WARNING: Make sure the saw blade or bladeguard will not hit
the work clamp assembly whencutting 35° to 45 ° angles. Failure to
heed thiswarning can result in serious personal injury.
MITERTABLE BASE
WORKCLAMP
Fig. 2
DUST BAG
See Figure 3.
The dust bag fits over the exhaust port on the upperblade guard.
To install it, remove the dust guide fromthe exhaust port. Then,
squeeze the two metal clips toopen the mouth of the bag and slide
it on the exhaustport. Release the clips. The metal ring in the
bagshould lock in between the grooves on the exhaustport. For more
efficient operation, empty dust bagwhen no more than half full.
This will permit better airflow through the bag.
DUSTBAG
EXHAUSTPORT
Fig. 3
TABLE EXTENSIONS
See Figure 4.
To install table extensions, insert the ends of theextensions
into the holes in the sides of the base.Secure them in place by
positioning a clamp bracketunder each table extension beneath the
miter table.Orient each clamp bracket as shown in figure 4.Secure
each clamp bracket in place with a clampbracket screw. The clamp
bracket screw threadsthrough the clamp bracket and tightens
againstbottom of miter table, securing clamp bracket againsttable
extension.
SAW VIEWEDFROM BELOW
CLAMPBRACKET
TABLE EXTENSION
Fig. 4
-
STOP BLOCK
See Figures 5 and 6.
The stop block is useful as a stop for cutting multiplepieces to
the same length. It can be installed on eithertable extension on
either side of the saw base:
• Slide the stop block on the back arm of either tableextension,
then insert the table extension into thesaw base. See Figure 5.
• Use the small wing screw to secure the stop blockto the table
extension. See Figure 5.
• Loosen the small wing screw and adjust the stopblock the
desired distance from the blade for thecut to be made.
STOPBLOCK
SMALLWINGSCREW
MITERSAWBASE
TABLE EXTENSION Fig. 5
• Tighten small wing screw securely.
• Make a test cut in scrap material and measure thelength of the
workpiece.
• Make any necessary adjustments.
WARNING: When using the work clamp withthe stop block, install
the clamp on the stop blockside of the blade. This will eliminate
thepossibility of the saw catching the loose end andkicking up.
Failure to heed this warning canresult in serious personal
injury.
STOPBLOCK
Fig. 6
-
Manual del usuario
ACCESORIOS PARA LA SIERRA DE ANGULO COMPUESTO DE 10pulgadas (254
mm) MODELO NOS. 315.212100, 315.212110 Y 315.243150
Art. No.924310924350_924352
Conserve este manual
para referencia futura
ATENCION" Lea cuidadosamente todaslas Reglas de Seguridad y las
Instruccionesantes de usar esta herramienta.
No. de telefono de ayuda a los clientes: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visite la pagina Webde Craftsman www.sears.com/craftsman
972000-60303-01
• SEGURIDAD
• PIEZAS SUELTAS
• INSTALACION
• SERVICIOS
-
LEA TODAS LAS INSTRUCCIONES
• LEA ATENTAMENTE ESTAS INSTRUCCIONESY LAS INSTRUCCIONESDE LA
SIERRA DE ANGULO COMPUESTO315.212100, 315.212110 y 315.243150 antes
deutili7ar los accesorios.
• FAMILIARICESE CON SU HERRAMIENTA. Leacuidadosamente el manual
del usuario de la sierrade angulo compuesto. Aprenda cuales son
lasaplicaciones y limitaciones de la sierra, as{ comolos peligros
espec{ficos relacionados con estaherramienta.
• MANTENGA LIMPIA LA ZONA DE TRABAJO.Las areas y bancos de
trabajo congestionados sonuna invitaci6n a tener accidentes. NO
DEJE las
herramientas o piezas de madera en la sierramientras la misma
est6 funcionando.
• UTILICE SIEMPRE GAFAS DE SEGURIDAD. Losanteojos normales
solamente tienen lentesprotectores contra el choque; NO SON gafas
deseguridad.
• DESCONECTE SIEMPRE LA SIERRA DE LACORRIENTE ANTES DE HACER
AJUSTES OAGREGAR ACCESORIOS. Verifique que elinterruptor est6
apagado antes de reconectar lasierra a la corriente.
GUARDE ESTAS INSTRUCCIONES. ConsL_ltelascon frecuencia y
utilicelas para instruir a otrosusuarios. Si le presta la maquina a
alguien,pr6stele tambi6n estas instrucciones.
Busque este simbolo, que indica precauciones importantesde
seguridad. ;Significa atenci6n! Esta en juego su seguridad.
Los siguientes accesorios vienen incluidos con el articulo No.
924310, 924350 y 924352:
• Mordaza de trabajo • Tornillo peque_o de palomilla
• Bolsa para polvo • Brida de apriete (2)
• Extensiones de la mesa (2) • Tornillos de la brida de apriete
(2)
• Bloque de parada • Manual del usuario
MORDAZADETRABAJO
BOLSAPARAPOLVO
/TORNILLOPEQUEItO
DE PALOMILLABLOQUE
DE PARADA
EXTENSIONESDELA MESA
BRIDADEAPRIETE
ADVERTENClA: El uso de agregados o accesorios no listados puede
ser peligroso.
2
TORNILLO
Fig. 1
-
A ADVERTENClA: Para evitar el peligro de quela sierra arranque
accidentalmente y causeposibles lesiones graves, monte
completamentetodas las piezas en la sierra antes de conectarlaa la
corriente. La sierra jamas debe estarconectada a la corriente
mientras se est6nmontando piezas, haciendo ajustes, instalando
osacando hojas o accesorios, o cuando no est6en uso.
ABRAZADERA DE TRABAJOVea la Figura 2.
La abrazadera de trabajo proporciona un mayorcontrol, ya que
aprieta la pieza de trabajo contra ladefensa. Tambien impide que la
pieza de trabajo sedeslice hacia la hoja de la sierra. Esto resulta
muy Qtilcuando se hacen cortes de angulo compuesto. Parainstalar la
mordaza de trabajo, coloque el vastago dela mordaza en uno de los
dos agujeros situados en laparte frontal de la base de la mesa de
inglete. Hagagirar la perilla de la mordaza para moverla
haciaadentro o hacia afuera, segQn se necesite.
A ADVERTENClA: Verifique que la hoja de lasierra o la protecci6n
de la hoja no toque elconjunto de la mordaza de trabajo cuando
cortea un angulo de 35 ° a 45 °. De ignorarse estaadvertencia,
pueden ocurrir lesiones graves.
BASEDE LA MESADE INGLETE
MORDAZADETRABAJO
Fig. 2
BOLSA PARA POLVOVea la Figura 3.
La bolsa para polvo calza sobre el puerto de escapesituado en la
protecci6n superior de la hoja. Parainstalarla, saque la guia del
polvo del puerto deescape. Despues apriete los dos clips metalicos
paraabrir la boca de la bolsa y deslizarla sobre el puertode
escape. Suelte los clips. El anillo metalico de labolsa debe calzar
entre las estrias del puerto deescape.Para un funcionamiento mas
eficaz, vacie labolsa guardapolvo cuando est6 a medio Ilenar.
Estopermitira que el aire circule mejor a trav6s de la bolsa.
Fig. 3
EXTENSIONES DE LA MESAVea la Figura 4.Para instalar las
extensiones de la mesa, inserte losextremos de las extensiones en
los agujeros de loscostados de la base. AsegQrelas en su
lugarcolocando una brida de apriete debajo de cadaextensi6n de mesa
bajo la mesa de inglete. Orientecada una de las bridas de apriete
en su lugar con untornilla a trav6s de la brida de apriete y
quedaapretado contra la parte inferior de la mesa de
inglete,asegurando la brida de apriete contra la extensi6n dela
mesa.
EXTENSIONDELA MESA
Fig. 4
3
-
BLOQUE DE PARADAVea las Figuras 5 y 6.
El bloque de parada es Otil para cortar varias piezas ala misma
Iongitud. Puede instalarse en cualquiera delas dos extensiones de
la mesa, a uno de los doslados de la base de la mesa:
• Deslice el bloque de parada sobre el brazo traserode una de
las extensiones de la mesa, y despuesinserte la extensi6n de la
mesa en la base de lasierra. Vea la Figura 5.
• Utilice el pequeSo tornillo de palomilla paraasegurar el
bloque de parada a la extensi6n de lamesa. Vea la Figura 5.
• Afloje el tornillo pequeSo de palomilla y ajuste elbloque de
parada a la distancia deseada de la hojapara efectuar el corte.
BLOQUEDEPARADA
TORNILLOPEQUEItODEPALOMILLA
BASEDELA MESADEINGLETE
EXTENSIONDE LAMESA Fig. 5
• Apriete bien el tornillo peque_o de palomilla.• Haga un corte
de prueba en material de desecho y
mida la Iongitud de la pieza de trabajo.
• Haga los ajustes necesarios.
_, ADVERTENCIA: Cuando utilice la mordaza detrabajo junto con el
bloque de parada, instale lamordaza del mismo lado que el bloque
deparada con respecto a la hoja. Esto eliminara laposibilidad de
que la sierra atrape el extremosuelto y produzca un rechazo. De
ignorarse estaadvertencia, pueden ocurrir lesiones graves.
BLOQUEDEPARADA
Fig. 6
4