OWNER’S MANUAL - Bounty Hunter Metal Detectors · The Elite 2200 is a professional metal detector. While the most difficult aspects of metal detecting have been automated, it is

The Elite 2200 is aprofessional metal detector.

While the most difficult aspects of metal detecting havebeen automated, it is a sophisticated electronic device whichrequires an understanding of some basic features and metal detectingconcepts.

If you do not have prior experience with a metal detector, we stronglyrecommend that you:

1) Adjust the Sensitivity to a low setting in the event of falsesignals. Always begin use at a reduced sensitivity level; increase tofull sensitivity after you have become familiar with the detector.

2) Do not use indoors. This detector is for outdoor use only. Manyhousehold appliances emit electromagnetic energy, which caninterfere with the detector. If conducting an indoor demonstration,turn the sensitivity down and keep the searchcoil away fromappliances such as computers, televisions and microwave ovens.If your detector beeps erratically, turn off appliances and lights,especially those with dimmer switches.

Also keep the searchcoil away from objects containing metal, suchas floors and walls.

3) Read this manual. Most importantly, review the Quick-Start Demo(p.7-8) and Basic Operation (p. 9-11).

4) Use 9-volt ALKALINE batteries only. Do not use Heavy DutyBatteries.

O W N E R ’ S M A N U A L

BH-ELITE2200.qx6 7/3/07 3:20 PM Page 1

2

Table Of Contents

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . . . .7-8

Basic Operation . . . . . . . . . . . . . . . . . . . . . . . .9-12

All Metal . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Discrimination . . . . . . . . . . . . . . . . . . . . . . . .10

Notch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Zap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Audio Target Identification . . . . . . . . . . . . . . . . . . .13

Target and Depth Display . . . . . . . . . . . . . . . . . . . .14

Sensitivity Adjustment . . . . . . . . . . . . . . . . . . . . . .15

In The Field Techniques . . . . . . . . . . . . . . . . . .16-18

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . .19

Treasure Hunter’s Code of Ethics . . . . . . . . . .Back CoverWarranty . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover


3

Terminology

The following terms are used throughout the manual, and are standardterminology among detectorists.

ELIMINATIONReference to a metal being "eliminated" means that the detector willnot emit a tone, nor light up an indicator, when a specified objectpasses through the coil’s detection field.

DISCRIMINATIONWhen the detector emits different tones for different types of metals,and when the detector "eliminates" certain metals, we refer to thisas the detector "discriminating" among different types of metals.Discrimination is an important feature of professional metaldetectors. Discrimination allows the user to ignore trash andotherwise undesirable objects.

RELICA relic is an object of interest by reason of its age or its associationwith the past. Many relics are made of iron, but can also be madeof bronze or precious metals.

IRONIron is a common, low-grade metal that is an undesirable target incertain metal detecting applications. Examples of undesirable ironobjects are old cans, pipes, bolts, and nails.Sometimes, the desired target is made of iron. Property markers,for instance, contain iron. Valuable relics can also be composed ofiron; cannon balls, old armaments, and parts of old structures andvehicles can also be composed of iron.

FERROUSMetals which are made of, or contain, iron.

PINPOINTINGPinpointing is the process of finding the exact location of a buriedobject. Long-buried metals can appear exactly like the surroundingsoil, and can therefore be very hard to isolate from the soil.

PULL-TABSDiscarded pull-tabs from beverage containers are the most bothersometrash items for treasure hunters. They come in many different shapesand sizes. Pull-tabs can be eliminated from detection, but some othervaluable objects can have a magnetic signature similar to pull-tabs, andwill also be eliminated when discriminating out pull-tabs.

GROUND BALANCEGround Balancing is the ability of the detector to ignore, or "seethrough," the earth’s naturally occurring minerals, and only sound atone when a metal object is detected. The Elite 2200 incorporatesproprietary Squelch-Tech® circuitry to eliminate false signals fromsevere ground conditions


4

Assembly

Assembly is easy and requires notools.

●1 Position the lower stem (the straight tube)with the silver button toward the back.Using the bolt and knurled knob, attach the searchcoil to the plastic extension protrudingfrom the lower stem.

●2 Press the button onthe upper end ofthe lower stem,and slide the lowerstem into theupper stem.

Adjust the stem to a lengththat lets you maintain acomfortable uprightposture, with your armrelaxed at your side, andthe searchcoil parallel tothe ground in front of you.

●3 Wind the cable securely around the stem.

●4 Insert the plug into thematching connector onthe right underside of thedetector body. Be surethat the key-way and pinsline up correctly.

Caution: Do not force the plugin. Excess force willcause damage.To disconnect thecable, pull on the plug.Do not pullon the cable.


5

Assembly

SE

NS

ITIV

ITY

DIS

CR

IMIN

AT

ION

Adjusting the Arm RestMost people will find the standard positionof the arm rest very comfortable. Very largeforearms and short forearms (particularlychildren’s arms), can be accommodatedby moving the arm rest forward.

The arm rest is adjustable to three positions.

To adjust, remove the screw from theunderside, then press the silver buttonand move the arm rest to one of thealternate positions. If you cannot fullydepress the button with your finger, usea narrow object, such as the blunt endof a ballpoint pen. The arm rest mustbe twisted with moderate force to moveit to an alternate position; thisadjustment is usually made infrequently.

If desired for added stability, re-installthe screw. The screw is not re-installedin the furthest forward position.

If the button becomes disengaged insideof the tube, remove the plastic cap at theend of the tube to access the clip inside.With a pair of needle-nose pliers,reengage the button. Then replace theplastic cap.


6

Use ALKALINEbatteries only.

To install thebatteries:

●1 Remove thebattery cover bydisengaging theclip at the back.

●2 Align the polarityof the batteriescorrectly, withthe positive "+"toward the coilplug connection,as indicated bythe + and –indicators on thehousing.

●3 Insert (2) 9-Volt ALKALINE batteries, with the contacts pointed inward,and press down on the back of the batteries to snap them into place.

Some brands of batteries will require moderate force to clear theretaining tabs.

If the batteries fit loosely, and you wantto guarantee a very secure electricalcontact, insert a piece of paper or thincardboard between the back of thebattery and the supporting post.

●4 Close the battery door.

When only the bottom segment of thebattery indicator is illuminated, replace thebatteries.

Most metal detector problems are due to improperly installed batteries,or the use of non-alkaline or discharged batteries. If the detector doesnot turn on, please check the batteries.

If the detector does not turn on, check to see that the batteries fit tightly.If the batteries are loose, press them forward while pressing the POWERtouchpad. To tighten up a loose battery, wedge a piece of paper or thincardboard between the back of the battery and the supporting post, asillustrated above.

Batteries

IN CASE OF LOOSE BATTERIES


7

Quick-Start Demostration

I. Supplies Needed• A Nail • A Quarter• A Pull-Tab from a beverage can • A Zinc Penny (dated after 1982)

II. Position the Detectora. Place the detector on a

table, with the searchcoilhanging over the edge.(or better, have a friendhold the detector, withthe coil off the ground)

b. Keep the searchcoil awayfrom walls, floors, andmetal objects.

c. Remove watches, rings and other jewelry or metal objects fromhands and wrists.

d. Turn off appliances or lights that cause electromagneticinterference.

e. Pivot the searchcoil backtoward the detector body.

III. Power UpPress the POWER touchpad.

IV. Wave each Object over the searchcoila.Notice a different tone for each object.

Bass Tone: NailLow Tone: Pull-TabMedium Tone: Zinc PennyHigh Tone: Quarter

b.Motion is required. Objects must be in motion over the searchcoil to be detected.

V. Press the DISC A-M touchpadThe detector will beep twiceand an “R” will appear underthe iron indicator.

Quick-Start Demo continued on next page


8

VI. Wave the Nail over the searchcoila. The Nail will not be detected.b. The Nail has been "Discriminated Out."

VII. Press the “DISCRIMINATION-▲” touchpad twice.

Three “R”s are now displayed.

VIII. Wave all objects over the searchcoilThe Nail and Pull-Tab will not be detected.The other objects will be detected with their own distinctive tones.

IX. Press the NOTCH touchpad.A flashing “R” will appear under the 5¢/PT segment.

X. Press the DISCRIMINATION ▲touchpad three times.

The flashing “R” will moveto the ZINC segment.

XI. Press the NOTCH touchpad again.The “R” will appear under zinc.

XII. Wave the zinc penny over the searchcoil. The penny is discriminated out.

XIII. Press the DISC A-M touchpadThe detector returns to ALL-METAL mode. No “R”s are displayed.All types of metals will be detected.

XIV. Wave the pull-tab over the coil.

XV. Press the ZAP touchpad.An “R” will appear.

XVI. Wave the pull-tab over the searchcoil again.

The pull-tab (the most recently detected item) is eliminated fromdetector.

Quick-Start Demostration (continued)


9

Basic Operation

POWERING UPPress the POWER touch pad.

• The detector will beep 4 times• All display segments will illuminate momentarily• The SENSITIVITY and BATTERY indicators will

stay illuminated

SENSITIVITYThe detector’s default sensitivity will be indicated with two segments.At this setting, the detector will detect a coin-sized object, such as aquarter, buried approximately seven inches deep. To change thesensitivity level, and thus the detection depth, press the SENSITIVITY▲ or ▼ keys.

CAUTION:At higher sensitivity levels, the detector is susceptible to electromagneticinterference from electronic devices. Reduce sensitivity if demonstratingindoors or if using near power lines or electrical equipment.Reduce sensitivity if detector emits false signals


10

DEFAULT OPERATIONThe detector defaults to ALL METAL mode after powering on. In thismode, all types of metals will be detected. An object’s probableidentification is indicated by the arrows at the top of the display. Inaddition, the probable depth of coin-sized objects is indicated by thelarge numeric indicator in the center of the display. All detectedobjects will cause the depth indicator to illuminate. The depthindication is not accurate forlarger objects; however, it willprovide accurate relativedepth indications. Thegreater the distance an objectis from the searchcoil, thegreater its depth value.

DISC/ A-M Touch PadPressing this touch pad willcause the detector to togglebetween two operatingmodes, DISCRIMINATIONand ALL-METAL. If thedetector is in the ALL-METAL mode (the default mode), pressing thetouch pad will change the detector into DISCRIMINATION mode. Ifthe detector is in the DISCRIMINATION mode, pressing the touch padwill change the detector into ALL-METAL mode.

DISCRIMINATION MODEDiscrimination is used to eliminate unwanted objects from detection.To enter this mode, from ALL-METAL mode, press the DISC/A-M touch pad.After pressing DISC/A-M, the detector will:

• Beep twice• Display an "R" under the left-most segment, Iron

Ferrous objects will not be detected in DISCRIMINATION mode. Heavily oxidized ferrous objects will sometimes, however, bedetected, usually with a high tone and an indication to the right ofthe target identification scale.

To increase the level of discrimination, press the DISCRIMINATION ▲

Basic Operation (continued)


11

touch pad. Each time the ▲ pad is depressed, an additional "R" willappear, thus eliminating from detection the objects which fall into thecorresponding categories.

To decrease the level of discrimination, press the DISCRIMINATION ▼touch pad. Each time the ▼ pad is depressed, an illuminated "R" willdisappear, thus returning to detection the objects which fall into thecorresponding categories.

Discrimination Mode is a fixed-start-point elimination system. Objectsare cumulatively eliminated as the level of discrimination increases.

NOTCH MODETo selectively eliminate a category from detection within the metallicspectrum, use the NOTCH Mode.

Technical Note:The NOTCH touch pad causes the status of an "R" segment totoggle between ON and OFF.

To use the NOTCH Mode:The NOTCH touch pad can be depressed at any time. But forfirst-time use, place the detector in ALL-METAL mode.

A first demonstration is best accomplished as follows:1) Turn the power OFF.2) Turn the power ON.3) Press NOTCH.

A flashing "R" will appear under the IRON segment.4) Press the DISCRIMINATION ▲ touch pad several times

Notice that the "R" moves upon each press of the DISCRIMINATION ▲ touch pad.

5) Press NOTCH again.The flashing "R" will become permanently illuminated.

If an object has been “notched-out”, you can return it to detectionstatus. To “un-notch” a category:

1) Press NOTCH.2) Move the flashing “R” over the permanently illuminated “R”.3) Press NOTCH again.



12


ZAPThe ZAP control is a convenient way to eliminate a known undesirable metal object from detection.

To demonstrate the ZAP control:

1) Set the detector in All-Metal ModeNote: ZAP functions in all modes, but is best demonstrated

first from the All-Metal Mode.2) Pass the searchcoil over an undesirable object.3) Notice the Target Indication

Note: You can only ZAP objects that register under the five left-most segments (from Iron to Zinc).

4) Press ZAP. An "R" appears under the segment to be eliminated.5) Pass the searchcoil over the same object again.

The undesirable object is eliminated from detection

The ZAP control is easy to use in the field. As you are detecting, andencounter an object which you wish to eliminate from detection,simply press the ZAP touch pad after detecting the object.

The ZAP control eliminates the most-recently detected object categoryfrom detection. The category eliminated is indicated with an "R".

HEADPHONE JACKUsing headphones(not supplied) withyour metal detectormakes it easier toidentify subtle changesin the threshold levelsfor better detectionresults, and alsoreduces drain on thebatteries. The Elite2200 Metal Detectorhas a stereoheadphone jacklocated at the rear ofthe case.This device is to beused with interconnect-ing cables/headphonecables shorter thanthree meters.

13

Audio Tareget Identification

While the LCD (Liquid Crystal Display) is very accurate in identifyingburied objects, the user in the field does not always maintain the displayscreen in his field of vision. Therefore, we have incorporated an audiofeedback mechanism to alert the user to the nature of buried objects.This audio feedback system first alerts the user to the presence andclassification of objects, whose nature and location can be confirmedusing the LCD display.

The detector can sound four different tones, depending on the objectdetected.

BASS TONEFerrous objects, such as iron and steel, will induce a bass tone.The smallest gold objects can also induce a bass tone.

LOW TONEPull-Tabs, nickels & smaller gold

MEDIUM TONENewer pennies (post-1982), larger gold objects, zinc, small brassobjects, and most bottle screw caps will induce medium tones.Many recent vintage foreign currencies will induce medium tones.

HIGH TONESilver and copper coins, larger brass objects, older pennies (pre-1982), and very large objects of any type of metal will inducehigh tones. Quarters, dimes and other precious coins fall into thiscategory.

Audio Target Identification (ATI) classifies metals into four categories.

BASS TONE

Nails, Steel bottle caps,Iron Objects,

& Smallest Gold Objects

LOW TONE

Pull Tabs, Nickels,& Smaller Gold

MEDIUM TONE

Zinc Pennies (Post1982), Larger Gold

Objects, Many screwcaps

HIGH TONE

Copper, Silver & BrassCopper Pennies (Pre

1982)


14

Depth and Target Display

READING THE DISPLAYThe Liquid Crystal Display (LCD) showsthe PROBABLE identification of thetargeted metal, as well as the PROBABLEdepth of the target, in inches.

The detector will register a repeated,unchanging target identification when aburied target has been located andidentified. If, upon repeated passes overthe same spot, the target identificationreads inconsistently, the target is probablya trash item, or oxidized metal. Withpractice, you will learn to unearth only therepeatable signals.

The segment identifications are highlyaccurate, when detecting the objectsdescribed on the label. However, if youregister in a given category for an unknownburied object, you could be detecting ametallic object other than the objectdescribed on the label, but with the samemetallic signature. Also, the greater thedistance between the target and the coil,the less accurate the target identification.

GOLD TARGETS Gold objects willregister on the left side of the LCD scale.

Gold flakes will register under Iron/FoilSmall gold items will register under PT.Medium-sized gold items will registerunder S-cap.Large gold items will register under Zinc.

SILVER TARGETS: Silver objects willregister to the right of the scale, under25¢, 50¢, or $1, depending on the sizeof the object. The larger the object, thefarther to the right it will register.IRON/FOIL: All sizes of iron andaluminum objects will register on thefar-left side of the scale. This couldindicate a worthless item such as a nail,or a more valuable historic iron relic.PT (pull tab): All older pull tabs frombeverage cans will register here. Somenewer pull tabs will register here. Many

gold rings will also register here.S-CAP: Older screw caps from glassbottles will register here. Large goldrings, like a class ring, could also registerhere. Some non-U.S. coins of recentvintage will also register here.

ZINC: Newer pennies (post-1982) willregister here. Many non-U.S. coins ofrecent vintage will also register here.

10¢: Dimes and pre-1982 pennies willregister here. Older, pre-1982, penniesare composed of copper, which has ametallic signature similar to a dime.

Caution: The target indications are visualreferences. Many other types of metalcan fall under any one of thesecategories. While the Elite 2200 willeliminate or indicate the presence of mostcommon trash items, it is impossible toaccurately classify ALL buried objects.

DEPTH INDICATOR:The Depth Indicator is calibrated tocoin-sized objects. It indicates thedepth of the target, in inches. Largeand irregularly-shaped objects willyield less reliable depth readings

When passing over an object, thedepth indicator will light up and stayilluminated until another object isscanned. Repeated indication at thesame depth level indicates an accuratetarget detector. If the depth indicationvaries with each sweep, try sweepingat different angles; there may be morethan one target present. With practice,you will learn the difference betweenaccurate readings, multiple targets,and highly erratic readings whichevidence trash or irregularly shapedobjects.


15

ELECTROMAGNETICINTERFERENCEThe principle use for theSensitivity Control is toeliminate ElectromagneticInterference (EMI).A hobby metal detector is anextremely sensitive device;the searchcoil creates itsown magnetic field and actslike an antenna. If yourdetector beeps erraticallywhen the searchcoil ismotionless, the unit is probably detecting another electromagnetic field.

Common sources of EMI are electric power lines, both suspended andburied, motors, and household appliances like computers andmicrowave ovens. Some indoor electronic devices, such as dimmerswitches used on household lighting, produce severe EMI and can causethe detector to beep erratically. Other metal detectors also produce theirown electromagnetic fields; so if detecting with a friend, keep two metaldetectors at least 20 feet apart.

If the detector beeps erratically, REDUCE THE SENSITIVITY bypressing the Sensitivity ▼ Pad on the left of the control panel.

SEVERE GROUND CONDITIONSA secondary use for the Sensitivity Control is to reduce false detectionsignals caused by severe ground conditions. While your Elite 2200contains circuitry to eliminate the signals caused by most naturallyoccurring ground minerals, 100% of all ground conditions cannot beanticipated. Highly magnetic soils found in mountainous and gold-prospecting locations can cause the detector to emit tones when metalobjects are not present. High saline content soils and sands cansometimes cause the detector to false.

If the detector emits false, non-repeatable, signals, REDUCE THESENSITIVITY.

MULTIPLE TARGETSIf you suspect the presence of deeper targets beneath a shallower target,reduce the sensitivity to eliminate the detection of the deeper targets, inorder to properly locate and identify the shallower target.

Sensitivity Adjustment


16

In The Field Techniques

When pinpointing a target, try drawing an “X”,as illustrated, over where the tone is induced.

PINPOINTINGAccurate pinpointing takes practiceand is best accomplished by“X-ing” the target area.

1. Once a buried target is indicatedby a good tone response,continue sweeping the coil overthe target in a narrowingside-to-side pattern.

2. Take visual note of the place onthe ground where the “beep”sounds.

3. Stop the coil directly over thisspot on the ground.

4. Now move the coil straightforward and straight backtowards you a couple of times.

5. Again make visual note of thespot on the ground at whichthe “beep” sounds.

6. If needed, “X” the target atdifferent angles to “zero in” onthe exact spot on the ground atwhich the “beep” sounds.

COIL MOVEMENTWhen swinging the coil, becareful to keep it level with theground about one inch from thesurface. Never swing the coil likea pendulum.

CORRECT

WRONG


17

Swing the searchcoil slowly,overlapping each sweep as youmove forward. It is importantto sweep the coil at a consistentspeed over the ground as yousearch. After identifying atarget, your sweep techniquecan help in identifying both thelocation and the nature of thetarget. If you encounter a weaksignal, try moving the coil in

short, rapid sweepsover the target zone;

such a short rapidsweep may provide

a more consistenttarget

identification.

Mostworthwhile

objectswill

respond with a repeatable tone.If the signal does not repeatafter sweeping the coil directlyover the suspected target a fewtimes, it is more than likelytrash metal.

Crossing the target zone withmultiple intersecting sweeps atmultiple angles is another wayto verify the repeatability of thesignal, and the potential of theburied target. To use thismethod, walk around the targetarea in a circle, sweeping thecoil across the targetrepeatedly, every 30 to 40degrees of the circle, about tendifferent angles as you walkcompletely around the target.If a high-tone target completelydisappears from detection at agiven angle, chances are thatyou are detecting oxidizedferrous metals, rather than asilver or copper object. If thetone changes at different

In The Field Techniques (continued)

WHATREADSLIKE THIS

…MAYACTUALLYBE THIS


18

angles, you may haveencountered multiple objects.If you are new to the hobby,you may want to dig all targetsat first. With practice in thefield, you will learn to betterdiscern the nature of buriedobjects by the nature of thedetector’s response.

You may encounter some falsesignals as you proceed. Falsesignals occur when the detectorbeeps, but no metal target ispresent. False signals can beinduced by electromagneticinterference, oxidation, orhighly mineralized groundsoils. If the detector beepsonce, but does not repeat thesignal with several additionalsweeps over the same spot,there is probably no targetpresent.

When searching very trashyground, it is best to scan smallareas with slow, short sweeps.

You will be surprised just howmuch trash metal and foil youwill find in some areas. Thetrashiest areas have beenfrequented by the most people,and frequently hold the mostpromise for finding the mostlost valuables. Also maintain the searchcoilpositioned just above thesurface of the ground, withoutmaking contact with theground. Making contact withthe ground can cause falsesignals.

In The Field Techniques (continued)


19

TROUBLE SHOOTING GUIDESYMPTOM CAUSE SOLUTION

Detector chatters • Using detector • Use detectoror beeps erratically indoors outdoors only

• Using detector near • Move away power lines (buried from power linesor overhead) • Keep 2 detectors

• Using 2 detectors in at least 20’ apartclose proximity • Only dig up

• Highly oxidized repeatable buried object signals

• Environmental • Reduce sensitivityelectromagnetic until erratic interference signals cease

Constant low tone • Discharged batteries • Replace batteriesor constant repeatingtones • Wrong type of • Use only 9V

batteries alkaline batteries

LCD does not lock • Multiple targets • Move coil slowlyon to one target ID present at different anglesor detector emits • Highly oxidizedmultiple tones target

• Sensitivity set • Reduce sensitivitytoo high

No power, no • Dead batteries • Replace batteriessounds • Poor battery • Push batteries in

contact tighter• Cord not connected • Insert paper spacers

securely (see page 6)• Check connections

Trouble Shooting


Treasure Hunter’s Code of Ethics:• Always check Federal, State, County and local laws before searching.• Respect private property and do not enter private property without the owner’s permission.• Take care to refill all holes and try not to leave any damage.• Remove and dispose of any and all trash and litter found.• Appreciate and protect our inheritance of natural resources, wildlife and private property.• Act as an ambassador for the hobby, use thoughtfulness, consideration and

courtesy at all times.• Never destroy historical or archaeological treasures.• All treasure hunters may be judged by the example you set; always conduct yourself

with courtesy and consideration of others

First Texas Products, LP1465-H Henry Brennan

El Paso, TX 79936(915) 633-8354

Copyright ©2009 by First Texas Products, L.L.C.

All rights reserved, including the right to reproduce this book, or parts thereof, in any form, except for theinclusion of brief quotations in a review.

Published by First Texas Products, L.L.C.Bounty Hunter® is a registered trademark of First Texas Products, L.L.C.

www.detecting.com

ME2200071409

FIRST TEXAS PRODUCTS, LLC5-YEAR LIMITED WARRANTY

Bounty Hunter Metal Detectors are warranted against defects inworkmanship or materials under normal use for five years from

date of purchase to the original user. Liability in all events islimited to the purchase price paid. Liability under this Warranty islimited to replacing or repairing, at our option, any Bounty HunterDetector returned, shipping cost prepaid, to First Texas Products,LLC. Damage due to neglect, accidental damage or misuse of this

product is not covered by this warranty.

Proof of purchase is required to make a claim under this warranty.

NOTE TO FOREIGN COUNTRY CUSTOMERSThis warranty may vary in other countries, check with your distributor for details.

Factory warranty follows the channel of distribution.Warranty does not cover shipping costs

BH-ELITE2200.qx6 7/14/09 9:45 AM Page 20

OWNER’S MANUAL - Bounty Hunter Metal Detectors · The Elite 2200 is a professional metal detector. While the most difficult aspects of metal detecting have been automated, it is

Documents