OUTSULATION ® SMD SYSTEM ™ (Formerly SPRINT® MD SYSTEM®) An Exterior Wall Insulation and Finish System With Moisture Drainage Outsulation SMD System Installation Details (Formerly Sprint MD System) DS163
OUTSULATION® SMD SYSTEM™
(Formerly SPRINT® MD SYSTEM®)
An Exterior Wall Insulation and Finish System With Moisture Drainage
Outsulation SMD System Installation Details
(Formerly Sprint MD System)
DS163
MINOR PENETRATIONS OSMD 0.0.28
4RS
REV:APPROVED BY:
02/09
DATE:
Outsulation SMD System
of any project. The project design professional determines, in its sole
version.
®
is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
The architecture, engineering and design of the project using the
standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design
OSMD 0.0.34GABLE END WITH WOOD TRIM
OSMD 0.0.37CHIMNEY ENCLOSUREOSMD 0.0.36OSMD 0.0.35TERMINATION AT PARAPET
TERMINATION AT ROOF-TO-WALL FLASHING
SOFFIT TERMINATION OSMD 0.0.31OSMD 0.0.32OSMD 0.0.33
SOFFIT WITH FRIEZE BOARDGABLE END WITH EIFS TRIM
OSMD 0.0.30OSMD 0.0.29WOOD FRAMED DECK - CROSS SECTION
WOOD FRAMED DECK - CUT AWAY
OSMD 0.0.05FASTENING
ARCHED WINDOW HEAD OSMD 0.0.16
OSMD 0.0.22DOOR HEAD WITH INTEGRAL FLASHING
OSMD 0.0.25SYSTEM CONFIGURATION AT OPENINGSOSMD 0.0.26OSMD 0.0.27
SHUTTER AND DOWN SPOUT ATTACHMENTAESTHETIC REVEALS
OSMD 0.0.23OSMD 0.0.24
DOOR HEAD WITH BRICK MOLDINSIDE / OUTSIDE CORNERS
OSMD 0.0.19WINDOW SILL
OSMD 0.0.21OSMD 0.0.20DOOR JAMB WITH INTEGRAL FLASHING
DOOR JAMB WITH BRICK MOLD
OSMD 0.0.17OSMD 0.0.18
WINDOW HEADWINDOW JAMB
OSMD 0.0.11SEALANT CONFIGURATION OPTIONS
OPENING PREP - OSMD 0.0.14
OSMD 0.0.15BACKSTOP® NT WRB/ GRID TAPE™ OPTIONWINDOW ELEVATION
OSMD 0.0.13OSMD 0.0.12
OPENING PREP - BACKSTOP® NT WRB/ AQUAFLASH® SYSTEM OPTION
OPENING PREP - SHEET TYPE WRB
OSMD 0.0.08TERMINATION ABOVE GRADE
OSMD 0.0.10OSMD 0.0.09
VERTICAL EXPANSION JOINTSEXPANSION JOINT AT FLOOR LINE
OSMD 0.0.06OSMD 0.0.07FASTENING PATTERN - OUTSIDE CORNER
FASTENING PATTERN
OSMD 0.0.02DRYVIT DRAINAGE MAT™ OPTION
OSMD 0.0.04OSMD 0.0.03
OUTSIDE CORNER - HIGH IMPACTDUPONT™ TYVEK® STUCCOWRAP® OPTION
OSMD 0.0.01OUTSULATION SMD SYSTEM
TABLE OF CONTENTS
® ™
RS 02/094
DATE:REV:APPROVED BY:
Outsulation SMD System
this detail and for the architecture, design, engineering or workmanship
without notice. Contact Dryvit to insure you have the most recent
®
version.
of any project. The project design professional determines, in its sole
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
The architecture, engineering and design of the project using the
professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only
Dryvit products is the responsibility of the project's design
Outsulation SMD System
WOOD OR STEEL FRAMING
DRYVIT REINFORCING MESH
WRAP DRYVIT DETAILMESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
Drainage TrackOption
DRYVIT FINISHDRAINAGE STRIP
DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT MD SPACERCODE APPROVED WATER-RESISTIVE BARRIER
SUBSTRATE
OSMD 0.0.01
® ™
™
4 02/09RS
REV: DATE:APPROVED BY:
Outsulation SMD System
this detail and for the architecture, design, engineering or workmanship
version.
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change
of any project. The project design professional determines, in its sole
is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
®
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
The architecture, engineering and design of the project using the
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
Dryvit Drainage Mat™ Option
WOOD OR STEEL FRAMING
DRYVIT REINFORCING MESH
Drainage TrackOption
WRAP DRYVIT DETAILMESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
CODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT DRAINAGE MAT
SUBSTRATE
OSMD 0.0.02
® ™
REV:
RS
APPROVED BY:
02/09
DATE:
5
Outsulation SMD System
version.
®
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
discretion, whether this detail or a functionally equivalent alternative of any project. The project design professional determines, in its sole
2.1. DRYVIT DRAINAGE STRIP IS REQUIRED WHENUSING STUCCOWRAP WITHOUT A DRAINAGETRACK.
THE SELECTION OF A SPECIFICWATER-RESISTIVE BARRIER IS THERESPONSIBILITY OF THE SPECIFIER AND ISOUTSIDE THE SCOPE OF THIS DOCUMENT.
The architecture, engineering and design of the project using the
standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of
this detail and for the architecture, design, engineering or workmanship
Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and
NOTE:
Dupont Tyvek StuccoWrap Option
SUBSTRATE
DRYVIT FINISH
Drainage TrackOption
DRYVIT DRAINAGE STRIP(SEE NOTE 2)
WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT REINFORCING MESHDRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
DUPONT TYVEK STUCCOWRAP(REFER TO NOTES 1,2)
WOOD OR STEEL FRAMING
OSMD 0.0.03
® ™ ® ®
™
™
02/09RS 4
DATE:APPROVED BY: REV:
Outsulation SMD SystemDRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
1.NOTE:
of any project. The project design professional determines, in its sole
version.
®
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
2. The architecture, engineering and design of the project using the
this detail and for the architecture, design, engineering or workmanship
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of
Dryvit products is the responsibility of the project's design
Outside Corner- High Impact
203 MM (8") MIN.
DRYVIT MD SPACER
APPROVED OSMD SYSTEMINSULATION BOARD
DRYVIT STANDARD OR STANDARDPLUS REINFORCING MESH OVERLAPMIN. 203 MM (8") AT CORNER
DRYVIT FINISH
DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT CORNER MESH
DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT INTERMEDIATE MESH
CODE APPROVEDWATER-RESISTIVE BARRIER
SUBSTRATE
OSMD 0.0.04
® ™
™
19 MM (3/4") MIN.
4RS 02/09
REV:APPROVED BY: DATE:
Outsulation SMD System
of any project. The project design professional determines, in its sole
version.
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
®
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
The architecture, engineering and design of the project using the
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship
1. FOR NON-NAILABLE SHEATHINGSUBSTRATES, THE FASTENER MUST BEINSTALLED INTO THE FRAMING.
NOTE:
Fastening
APPROVED WASHERSUBSTRATE
25 MM (1") MIN.
MINIMUM 4.8 MM (3/16") DIAMETERCORROSION RESISTANT MASONRY SCREWAPPROVED OSMD SYSTEM INSULATIONBOARD
CONCRETE
MINIMUM NO. 6 CORROSIONRESISTANT SCREW
MINIMUM 12 GAUGE (8d) CORROSIONRESISTANT RING SHANK NAIL
NAILABLESUBSTRATE APPROVED OSMD SYSTEM INSULATION
BOARDMINIMUM NO. 6 CORROSIONRESISTANT SCREWNAILABLE SUBSTRATE
25 MM (1") MIN.
APPROVED WASHER
GYPSUM SHEATHING OR OTHERNON- NAILABLE SUBSTRATE
9.5 MM (3/8") MIN.
APPROVED WASHERMINIMUM NO. 6 SELF DRILLINGCORROSION RESISTANT SCREWAPPROVED OSMD SYSTEM INSULATIONBOARD
NON-NAILABLESUBSTRATESTEEL FRAMING
APPROVED WASHER19 MM (3/4") MIN.
25 MM (1") MIN.
GYPSUM SHEATHING OR OTHERNON- NAILABLE SUBSTRATEAPPROVED WASHERMINIMUM 12 GAUGE (8d) CORROSIONRESISTANT RING SHANK NAILAPPROVED OSMD SYSTEM INSULATIONBOARD
NON-NAILABLESUBSTRATEWOOD FRAMING
OSMD 0.0.05
® ™
DRAINAGE TRACK25 MM. (1") TYP.
APPROVED BY:
RS
REV:
4
DATE:
02/09
Outsulation SMD System Fastening Pattern
of any project. The project design professional determines, in its sole
version.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative
1. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
Dryvit products is the responsibility of the project's design
standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and
NOTE:The architecture, engineering and design of the project using the
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
VERTICAL INSULATION BOARDJOINT ALIGNED WITHDRYVIT MD SPACER
DRYVIT MD SPACER 3.2 MM X 76 MM (1/8" X 3")SPACED DIRECTLY BEHIND LINE OF FASTENERS
305 MM. (12")TYP. PERIMETER
DRYVIT REINFORCING MESH
APPROVED OSMD SYSTEM INSULATION BOARD
SUBSTRATE
305 MM. (12")O.C. TYP.
WOOD OR STEEL FRAMING
CODE APPROVED WATER-RESISTIVE BARRIER
406 MM. (16")O.C. TYP.
OSMD 0.0.06
® ™
™
OFFSET INSULATION BOARDEDGES AT CORNERS
Outsulation SMD SystemDRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
1.NOTE:
REV:
4RS
APPROVED BY: DATE:
02/09
Fastening Pattern - Outside Corner
of any project. The project design professional determines, in its sole
version.
®
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
2. CORNER MESH MAY BE USED IN ADDITION TODRYVIT REINFORCING MESH.
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship 3. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND
0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
The architecture, engineering and design of the project using the
DRYVIT REINFORCING MESHOUTSIDE CORNER (SEE NOTE 2)
WOOD OR STEEL FRAMING
406 MM(16") TYP.
OFFSET VERTICAL JOINTS
25 MM (1") FROM BOARD EDGE (TYP.)
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
305 MM(12") TYP.
DRYVIT MD SPACER PLACEDDIRECTLY BEHIND ROW OF FASTENERS
OSMD 0.0.07
® ™
™
REV:APPROVED BY: DATE:
4RS 02/09
Outsulation SMD System Termination Above Grade
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
of any project. The project design professional determines, in its sole
version.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
FLOOR LINE EXPANSION JOINT IS REQUIRED IF610 MM (24") DIMENSION IS EXCEEDED.
2.1.
3. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
NOTE:Dryvit products is the responsibility of the project's design
standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and
The architecture, engineering and design of the project using the
WRAP DRYVIT DETAILMESH® TO BACKSIDEOF EPS MIN. 51 MM (2")
DRAINAGE STRIP
CODE APPROVED WATER-RESISTIVEBARRIER LAPPED INTO DRAINAGE TRACKDRYVIT MD SPACER LAPPED OVERFLANGE OF DRAINAGE TRACKAPPROVED OSMD SYSTEM INSULATION BOARD
51 MM (2") MIN.610 MM (24") MAX. (SEE NOTE 2)
SEALANT WITHBOND BREAKER,
BY OTHERS
NOTCH INSULATION BOARDTO ACCOMMODATE TRACK,
WATER-RESISTIVE BARRIER,AND SPACER.
203 MM (8") MIN. ABOVE FINISHED GRADEOR AS REQUIRED BY LOCAL CODE
Drainage StripOption
SLOPED DRAINAGE TRACK
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
DRYVIT FINISH
CONCRETE CONSTRUCTION DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
WOOD OR STEEL FRAMINGSUBSTRATE
OSMD 0.0.08
® ™
DRYVIT MD SPACER™
CODE APPROVED WATER-RESISTIVE BARRIER
REV:APPROVED BY: DATE:
RS 4 02/09
Outsulation SMD System Expansion Joint at Floorline
GAP PLYWOOD TO ALLOW FORCROSS-GRAIN SHRINKAGE OF THE FLOORJOISTS. OFFSET SYSTEM EXPANSION JOINTAPPROXIMATELY 25 MM (1") BELOWPLYWOOD GAP. of any project. The project design professional determines, in its sole
version.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
1. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
2. Dryvit products is the responsibility of the project's design
standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and
NOTE:The architecture, engineering and design of the project using the
DRYVIT FINISH
SUBSTRATE
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
CODE APPROVED WATER-RESISTIVE BARRIERLAPPING OVER FLANGE OF DRAINAGE TRACK
19 MM (3/4") MIN.5
SEE NOTE 1
DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD,BY OTHERS. (DO NOT BLOCK TRACKDRAIN HOLES)
INSULATION BOARD TO ACCOMMODATEDRAINAGE TRACK, WATER-RESISTIVE
BARRIER, AND SPACER
WRAP DRYVIT DETAILMESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
APPROVED OSMD SYSTEM INSULATION BOARDSLOPE TOP EDGE
DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
1
DRYVIT MD SPACER™ LAPPEDOVER FLANGE OF DRAINAGE TRACK
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
WOOD OR STEEL FRAMING
OSMD 0.0.09
® ™
CONCRETECONSTRUCTION
REV:APPROVED BY: DATE:
4RS 02/09
Outsulation SMD System Vertical Expansion Joints
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
1.NOTE:
of any project. The project design professional determines, in its sole
version.
®
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
2. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
Dryvit products is the responsibility of the project's design
this detail and for the architecture, design, engineering or workmanship
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of
The architecture, engineering and design of the project using the
CORROSIONRESISTANT "L" TRIM
CODE APPROVED WATER-RESISTIVEBARRIER PUSHED INTO JOINT
TO ACCOMMODATE MOVEMENT
WRAP DRYVIT DETAILMESH® 51 MM (2") MIN. ATBACKSIDE OF INSULATION BOARD
DRYVIT DEMANDIT® ORCOLOR PRIME™ ON
SURFACE(S) TO RECEIVE SEALANT
19 MM (3/4") MIN. DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
OPTION
WRAP DRYVIT DETAIL MESH51 MM (2") MIN. AT BACKSIDE
OF INSULATION BOARD
DRYVIT APPROVED WASHERWITH CORROSION RESISTANT
FASTENER
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT FINISH
DRYVIT MD SPACER
APPROVED OSMD SYSTEM INSULATION BOARD
WOOD OR STEEL FRAMING
OSMD 0.0.10
® ™
APPROVED OSMD SYSTEM INSULATION BOARD
REV:APPROVED BY: DATE:
4RS 02/09
Outsulation SMD System Sealant Configuration Options
WEATHER SEAL JOINTS SUCH AS AT WINDOWAND DOOR PERIMETERS CAN USE ANGLE ORRECTANGULAR BEADS. RECTANGULAR BEADSUSED AS A WEATHERSEAL REQUIRE A MINIMUM12.7 MM (1/2") WIDTH. of any project. The project design professional determines, in its sole
version.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
EXPANSION JOINTS SHALL USE RECTANGULARBEADS AND BE DESIGNED FOR MINIMUM FOURTIMES THE ANTICIPATED MOVEMENT, BUT NOTLESS THAN 19 MM (3/4").
1. 2.NOTE:
Dryvit products is the responsibility of the project's design
this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the
w
t = 6.4 mm (1/4") min.w/t = 2:1
FOR RECTANGULAR BEADS:w = 12.7 mm (1/2") min. (SEE NOTES 1 AND 2)
WRAP DRYVIT DETAIL MESH51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
DRYVIT COMPATIBLE SEALANT WITHQUARTER ROUND BACKER ROD, BY OTHERS(REFER TO BOND BREAKER OPTIONS BELOW)
TRIANGULAR BACKER ROD BOND BREAKER TAPEof abutting material but not
DRYVIT DEMANDIT OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANT
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
DRYVIT REINFORCING MESH EMBEDDED INDRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
t
RectangularBead
less than 3.2 mm (1/8")
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
Angle Bead BondBreaker Options
w
t = 6.4 mm (1/4") min.w = specified by manufacturer
FOR ANGLE BEADS:
tt
AngleBead
t
OSMD 0.0.11
® ™
APPROVED BY: REV: DATE:
02/091RS
Outsulation SMD System Opening Prep -Sheet Type Water-Resistive Barrier
2. SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER SHALL BEINSTALLED IN A WEATHER BOARD FASHIONIN ACCORDANCE WITH CODE ANDMANUFACTURER'S REQUIREMENTS.
of any project. The project design professional determines, in its sole
version.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
Dryvit products is the responsibility of the project's design INSTALL WINDOW UNIT AND ASSOCIATEDFLASHINGS PER MANUFACTURER'SRECOMMENDATIONS, CODE REQUIREMENTSAND PROJECT DOCUMENTS. and Dryvit specifically disclaims any liability for the use of
this detail and for the architecture, design, engineering or workmansh
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
NOTE:1. The architecture, engineering and design of the project using the
INSTALL WINDOW UNIT AND ASSOCIATED FLASHINGSPER MANUFACTURER'S RECOMMENDATIONS, CODEREQUIREMENTS AND PROJECT DOCUMENTS.FOLD DOWN WATER-RESISTIVE BARRIER OVERHEAD FLASHING AND TAPE SEAMS WITH DRYVITFLASHING TAPE
STEP #3
3.)
APPLY DRYVIT FLASHING TAPE AND SURFACECONDITIONER ONTO HEAD AND LAP CODEAPPROVED SHEET TYPE WATER-RESISTIVEBARRIER OVER IN A WEATHER BOARD FASHION
2.)
1.)
CUT AND FOLD BACK CODE APPROVEDWATER-RESISTIVE BARRIER AT HEAD
SEE NOTE 2
4" MIN.
INSTALL DIAGONAL STRIPS OF DRYVIT FLASHINGTAPE AND SURFACE CONDITIONER AT CORNERSOVER PREVIOUSLY INSTALLED FLASHING TAPEAND WATER-RESISTIVE BARRIER
STEP #1 STEP #2
APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER ONTOJAMB AND OVER CODE APPROVEDSHEET TYPE WATER-RESISTIVEBARRIER
APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER™ ONTOSILL AND UP JAMBS LAPPING OVERCODE APPROVED SHEET TYPEWATER-RESISTIVE BARRIER 6" MIN.
(typ)
OSMD 0.0.12
® ™
DATE:REV:APPROVED BY:
RS 02/092
Outsulation SMD System NOTE:
Opening Prep - Backstop® NT WRB/AquaFlash® System Option
4. APPLY CAULK BEHIND HEAD AND JAMBFLANGES OF WINDOW.
SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER MAY BE USEDAND SHALL BE INSTALLED IN A WEATHERBOARD FASHION IN ACCORDANCE WITH CODEAND MANUFACTURER'S REQUIREMENTS.
of any project. The project design professional determines, in its sole
version.
®
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
2. DRYVIT OPENING WRAP SHALL EXTEND TOINTERIOR FACE OF FRAMING.
3.1. APPLY DRYVIT BACKSTOP NT/-SMOOTHOR TEXTURE OVER REMAINDER OF WALLSURFACE.
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
The architecture, engineering and design of the project using the
STEP #4STEP #3
APPLY DRYVIT AQUAFLASHSYSTEM AT HEAD LAPPINGOVER JAMB APPLICATION
APPLY DRYVIT AQUAFLASHSYSTEM AT JAMBS LAPPINGOVER SILL APPLICATION
DRYVIT WATER-RESISTIVEBARRIER COATING(SEE NOTE 3)
STEP #2STEP #1
INSTALL DIAGONAL STRIPOF DRYVIT AQUAFLASHSYSTEM AT CORNERS(JAMB AND SILL)
APPLY DRYVIT AQUAFLASHSYSTEM AT SILL, EXTENDINGUP JAMBS MINIMUM 2 12"
OSMD 0.0.13
® ™
APPROVED BY: REV: DATE:
APPLY DRYVIT FLASHING TAPE SURFACECONDITIONER AND DRYVIT FLASHING TAPEAT SILL, INCLUDING CORNER SPLICES. 02/091RS
Outsulation SMD System Opening Prep - Backstop® NT WRB/Backstop NT / Grid Tape™ Option
of any project. The project design professional determines, in its sole
TROWEL APPLY DRYVIT BACKSTOP NT-TEXTURE OVER THE DRYVIT GRID TAPE ALLTHE WAY TO INSIDE FACE OF OPENING. ALLVOIDS MUST BE FILLED; MULTIPLE PASSES MAYBE REQUIRED. AS AN OPTION, DRYVIT GRIDTAPE AND DRYVIT BACKSTOP NT-TEXTUREMAY ALSO BE APPLIED AT THE SILL PRIOR TODRYVIT FLASHING TAPE APPLICATION.
APPLY DRYVIT BACKSTOP NT - SMOOTHOR TEXTURE OVER REMAINDER OF WALLSURFACE.SHEET TYPE CODE APPROVEDWATER-RESISTIVE BARRIER MAY BE USEDAND SHALL BE INSTALLED IN A WEATHERBOARD FASHION IN ACCORDANCE WITH CODEAND MANUFACTURER'S REQUIREMENTS.3.
6.
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent version.
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
INSTALL WINDOW UNIT AND ASSOCIATEDFLASHINGS PER MANUFACTURER'SRECOMMENDATIONS, CODE REQUIREMENTSAND PROJECT DOCUMENTS.
APPLY DRYVIT GRID TAPE ON CORNERS OFOPENING AND SHEATHING JOINTS.
5.2.
4. NOTE:1.
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use ofthis detail and for the architecture, design, engineering or workmanship
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the
DRYVIT WATER RESISTIVEBARRIER COATING APPLIEDTO FACE OF WALL(SEE NOTE 5)
APPLY DRYVIT FLASHING TAPEAND SURFACE CONDITIONER(SEE NOTES 2 AND 3)
STEP #3 STEP #4
4" MIN.
6" MIN.(typ)
STEP #1 STEP #2
APPLY DRYVIT GRID TAPE(SEE NOTES 1 AND 2)
TROWEL APPLY DRYVITBACKSTOP NT-TEXTURE(SEE NOTE 2)
OSMD 0.0.14
® ™
APPLY SEALANTTO FLASHING
JUNCTION
FLASHING INTEGRALWITH WINDOW
REV:APPROVED BY: DATE:
4RS 02/09
Outsulation SMD System Window Elevation
of any project. The project design professional determines, in its sole
®
does not violate Dryvit's warranty. This detail is subject to change
version.without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative
FLASHING TRANSITION BETWEEN CURVEDAND HORIZONTAL ASSEMBLIES MUST BEPROPERLY LAPPED AND SEALED TO SHEDWATER TO THE EXTERIOR.
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
NOTE:1. The architecture, engineering and design of the project using the
FLASHINGINTEGRAL
WITH WINDOW
OSMD 0.0.15
® ™
ARCHED WINDOW WITHINTEGRAL FLASHING
SUBSTRATE
FRAMING
REV:APPROVED BY: DATE:
RS 4 02/09
Outsulation SMD System Arched Window Head
discretion, whether this detail or a functionally equivalent alternative
®
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent version.
FOR NON-NAILABLE SHEATHINGSUBSTRATES, FASTENERS MUST BEINSTALLED INTO THE FRAMING.
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
The architecture, engineering and design of the project using the NOTE:1.
6APPROVED OSMD SYSTEM INSULATION BOARDOR EPS TRIM (OPTIONAL) ADHEREDWITH DRYVIT GENESIS, GENESIS DM OR GENESISDMS BASE COAT OR MECHANICALLY FASTENINTO SOLID SUBSTRATE- SLOPE TOP EDGE
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT MD SPACER
DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERSPROVIDE AIR SEAL AROUND
INTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS
12.7 MM (1/2") MIN.
DRYVIT FINISH
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)
APPROVED OSMD SYSTEM INSULATION BOARD
CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER NAILING FIN
12
OSMD 0.0.16
® ™
WINDOW WITH INTEGRAL FLASHING
SUBSTRATE
REV:APPROVED BY: DATE:
4RS 02/09
Outsulation SMD System Window Head
OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGEMEDIUM.
discretion, whether this detail or a functionally equivalent alternative
®
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent version.
is best suited for the project. Use of a functionally equivalent detail
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
2.
NOTE:1.
professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTE 2)
APPROVED OSMD SYSTEM INSULATION BOARDOR EPS TRIM (OPTIONAL) ADHEREDWITH DRYVIT GENESIS, GENESIS DM ORGENESIS DMS BASE COAT OR MECHANICALLYFASTEN INTO SOLID SUBSTRATE-SLOPE TOP EDGE
DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
PROVIDE AIR SEAL AROUND INTERIOROF WINDOW PER WINDOW
MANUFACTURER'S REQUIREMENTS
WOOD OR STEEL FRAMING
DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERS.PROVIDE WEEPS WITH BAFFLES EVERY610 MM (2'-0") ON CENTER
Drainage TrackOption
13 MM (1/2") MIN.
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENERWRAP DRYVIT DETAIL MESH® 51 MM(2") MIN. AT BACKSIDE OF INSULATION BOARDDRYVIT FINISH
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER NAILING FINAPPROVED OSMD SYSTEM INSULATION BOARD(SEE NOTE 2)DRYVIT MD SPACER
612
OSMD 0.0.17
® ™
APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE
WINDOW WITHINTEGRAL FLASHING
DRYVIT DEMANDIT® OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANTDRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
4RS 02/09
Outsulation SMD System Window Jamb
discretion, whether this detail or a functionally equivalent alternative
®REV:APPROVED BY: DATE:
without notice. Contact Dryvit to insure you have the most recent version.
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
FOR NON-NAILABLE SHEATHINGSUBSTRATES, THE FASTENER MUST BEINSTALLED INTO THE FRAMING.
professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
NOTE:1. Dryvit products is the responsibility of the project's design
The architecture, engineering and design of the project using the
WOOD OR STEEL FRAMING
CODE APPROVEDWATER-RESISTIVE BARRIER
DRYVIT MD SPACER
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT FINISH12.7 MM (1/2") MIN.
APPROVED OSMD SYSTEM INSULATIONBOARD
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
SUBSTRATE
OSMD 0.0.18PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS.
® ™
™
™
SUBSTRATE CODE APPROVEDWATER-RESISTIVE BARRIER
REV:APPROVED BY: DATE:
RS 4 02/09
Outsulation SMD System Window Sill
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
discretion, whether this detail or a functionally equivalent alternative
®
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent version.
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS. professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the
NOTE:2.1.
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH
APPROVED SYSTEMINSULATION BOARD
DRYVIT MD SPACER
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)
WINDOW WITH INTEGRAL FLASHING
PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS
DRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENERAPPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
13 MM (1/2") MIN.126
OSMD 0.0.19
® ™
™
APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM(OPTIONAL) ADHERED WITH DRYVITGENESIS, GENESIS DM OR GENESIS DMSBASE COAT OR MECHANICALLY FASTENINTO SOLID SUBSTRATEDOOR WITH INTEGRAL FLASHING
DRYVIT DEMANDIT® ORCOLOR PRIME ON SURFACE(S)TO RECEIVE SEALANTDRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
4RS 02/09
Outsulation SMD System Door Jamb With Integral Flashing
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
discretion, whether this detail or a functionally equivalent alternative
REV:APPROVED BY:
®DATE:
without notice. Contact Dryvit to insure you have the most recent version.
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
NOTE:1. 2.
professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
DRYVIT MD SPACERSUBSTRATE
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)CODE APPROVEDWATER-RESISTIVE BARRIER
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
DRYVIT FINISH
DRYVIT REINFORCING MESHEMBEDDED IN DRYVIT GENESIS®,GENESIS DM OR GENESIS DMSBASE COAT
12.7 MM (1/2") MIN.
APPROVED SYSTEMINSULATION BOARD
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
WOOD OR STEEL FRAMING
OSMD 0.0.20
PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS
® ™
™
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
APPROVED OSMD SYSTEMINSULATION BOARD
APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
DRYVIT FINISH
4RS 02/09
Outsulation SMD System Door Jamb With Brick Mold
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
discretion, whether this detail or a functionally equivalent alternative
REV:APPROVED BY: DATE:
®
without notice. Contact Dryvit to insure you have the most recent version.
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS. professional. All systems must comply with local building codes and
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only
NOTE:1. 2. Dryvit products is the responsibility of the project's design
The architecture, engineering and design of the project using the
PROVIDE AIR SEAL AROUNDINTERIOR OF WINDOW PER WINDOWMANUFACTURER'S REQUIREMENTS
SUBSTRATE
WOOD OR STEEL FRAMING
DOOR WITHBRICK MOLD
DRYVIT MD SPACER
CODE APPROVEDWATER-RESISTIVE BARRIER
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)
12.7 MM (1/2") MIN.
DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDE
OF INSULATION BOARD
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD
OSMD 0.0.21
® ™
™
DOOR WITH INTEGRALFLASHING
SUBSTRATE
WOOD ORSTEEL FRAMING
4RS 02/09
Outsulation SMD System Door Head With Integral Flashing
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
discretion, whether this detail or a functionally equivalent alternative
®APPROVED BY: REV: DATE:
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
version.
OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATE DRAINAGETRACK AND BARRIER / DRAINAGE MEDIUM.
professional. All systems must comply with local building codes and
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of
2.
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
NOTE:1.
CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTES 1 AND 2)
6 APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE
DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD. PROVIDEWEEPS WITH BAFFLES 610 MM (2'-0")ON CENTER
Drainage TrackOption
12.7 MM (1/2") MIN.
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENEROPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
OSMD 0.0.22
DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATION BOARDDRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH
12
CODE APPROVED WATER-RESISTIVE BARRIER
® ™
™
WOOD OR STEELFRAMING
SUBSTRATE
4RS 02/09
Outsulation SMD System Door Head With Brick Mold
OSMD INSULATION BOARD MAY NEED TO BENOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGEMEDIUM.
is best suited for the project. Use of a functionally equivalent detail
REV:APPROVED BY:
®DATE:
without notice. Contact Dryvit to insure you have the most recent version.
does not violate Dryvit's warranty. This detail is subject to change
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
2.
NOTE:1.
professional. All systems must comply with local building codes and
this detail and for the architecture, design, engineering or workmanship
discretion, whether this detail or a functionally equivalent alternative of any project. The project design professional determines, in its sole
and Dryvit specifically disclaims any liability for the use ofstandards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
CODE APPROVED WATER-RESISTIVEBARRIER AND DRAINAGE MEDIUMLAPPED OVER VINYL DRAINAGETRACK (SEE NOTES 1 AND 2)
APPROVED OSMD SYSTEM INSULATIONBOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE- SLOPE TOP EDGE
12.7 MM (1/2") MIN.
DRYVIT COMPATIBLE SEALANT WITH CLOSEDCELL BACKER ROD. PROVIDE WEEPS WITHBAFFLES EVERY 610 MM (2'-0") ON CENTER
DOOR WITHBRICK MOLD
Drainage TrackOption
DRIP FLASHING SETIN BED OF SEALANT
OPENING WRAP (SEEDETAILS OSMD 0.0.12-0.0.14)WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARDDRYVIT DEMANDIT® OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
OSMD 0.0.23DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH
612
CODE APPROVED WATER-RESISTIVE BARRIER
® ™
™
SUBSTRATE
DRYVIT MD SPACER
CODE APPROVED WATER-RESISTIVE BARRIER
4RS 02/09
Inside / Outside Corners
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
The architecture, engineering and design of the project using the
Outsulation SMD SystemDRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
DESIGNER SHALL DETERMINE THE NEED FOR ANEXPANSION JOINT AT CORNERS.
®REV:APPROVED BY: DATE:
version.
DO NOT LAP REINFORCING MESH WITHIN 203 MM(8") OF A CORNER.
3.
4.
and Dryvit specifically disclaims any liability for the use of
1.NOTE:
2. DOUBLE WRAP CORNERS WITH REINFORCINGMESH OR USE CORNER MESH.
Dryvit products is the responsibility of the project's design
MUST OVERLAP 203 MM (8") MIN.SEE ABOVE AND NOTES 2 AND 3
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS, GENESIS DMOR GENESIS DMS BASE COAT
APPROVED OSMD SYSTEM INSULATION BOARD
CODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
203 MM (8") MIN.(SEE NOTES 2 AND 3)
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
203 MM (8") MIN.(SEE NOTES 2 AND 3)
DRYVIT MD SPACERDRYVIT FINISH
OSMD 0.0.24
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
APPROVED OSMD SYSTEM INSULATION BOARDSUBSTRATE
™
™
® ™
4RS 02/09
Outsulation SMD System
is best suited for the project. Use of a functionally equivalent detail
®REV:APPROVED BY: DATE:
version.without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change
LOCATE INSULATION BOARDS SUCH THATBOARD EDGES DO NOT ALIGN WITHCORNERS OF PENETRATION. standards. This detail is for general information and guidance only
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
and Dryvit specifically disclaims any liability for the use of
discretion, whether this detail or a functionally equivalent alternative
APPLY A PIECE OF 241 MM (9 1/2") X 305 MM(12") DRYVIT REINFORCING MESH DIAGONALLYAT EACH CORNER.
2.
professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the 1.
NOTE:
DRYVIT DETAIL MESH241 MM (9 1/2") X 305 MM (12") (TYP.)
System Configuration At Openings
OFFSET INSULATION BOARDJOINTS FROM CORNERSOF OPENINGS
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
SPLICE PIECE OF DRYVIT DETAIL MESHREQUIRED AT CORNER
APPROVED OSMD SYSTEMINSULATION BOARD
OSMD 0.0.25
® ™
CORROSION RESISTANT SCREW AND SLEEVE
Outsulation SMD SystemDRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
is best suited for the project. Use of a functionally equivalent detail
RS
APPROVED BY:
®REV:
4
DATE:
02/09
version.
does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure you have the most recent
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
1. 2.NOTE:
standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative
and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship
Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and
The architecture, engineering and design of the project using the
Shutter And Downspout Attachment
DRYVIT COMPATIBLE SEALANT,BY OTHERS
DOWNSPOUT STRAP
DRYVIT COMPATIBLE SEALANTBETWEEN SYSTEM AND STRAP,BY OTHERS
DOWNSPOUT
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT FINISH
CORROSION RESISTANT SCREWCORROSION RESISTANT SLEEVESHUTTER
OSMD 0.0.2612.7 MM (1/2") MIN.
SUBSTRATE
WOOD OR STEEL FRAMING
CODE APPROVED WATER-RESISTIVE BARRIERDRYVIT MD SPACER
APPROVED OSMD SYSTEM INSULATION BOARD
® ™
™
Outsulation SMD SystemThe architecture, engineering and design of the project using the
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
®REV:
4RS
APPROVED BY: DATE:
02/09
version.
3. INSULATION BOARD THICKNESS MINUS THEDEPTH OF THE REVEAL SHALL NOT BE LESSTHAN 19 MM (3/4").
4.
and Dryvit specifically disclaims any liability for the use of
1.NOTE:
2. BOTTOM EDGES OF ALL REVEALS MUST BESLOPED FOR DRAINAGE.
Dryvit products is the responsibility of the project's design
Aesthetic Reveals
OVERLAP 64 MM (2 1/2") MIN.
19 MM (3/4") MIN. (SEE NOTE 3)
REVEAL OPTIONS
DRYVIT FINISH
CODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT DETAIL MESH®241 MM (9 1/2") X 305 MM (12") (TYP.)DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
APPROVED OSMD SYSTEM INSULATION BOARD
SUBSTRATE
OSMD 0.0.27
DRYVIT MD SPACER
WOOD OR STEEL FRAMING
™
® ™
DRYVIT FINISH
NOTE:DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
does not violate Dryvit's warranty. This detail is subject to change
®REV:APPROVED BY: DATE:
4RS 02/09
without notice. Contact Dryvit to insure you have the most recent version.
and Dryvit specifically disclaims any liability for the use of
of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
this detail and for the architecture, design, engineering or workmanship
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
1. 2. Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the
Outsulation SMD System Minor Penetrations
DRYVIT MD SPACER
CODE APPROVED WATER-RESISTIVE BARRIER
SUBSTRATE
WOOD OR STEEL FRAMING
CAULK PERIMETER OF PENETRATIONALONG SHEATHING.
12.7 MM (1/2") MIN.
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT DEMANDIT® OR COLOR PRIMEON SURFACE(S) TO RECEIVE SEALANT
WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
OSMD 0.0.28
® ™
™
™
DRYVIT COMPATIBLE SEALANT,BY OTHERS
WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
FLASHING NO. 1 EXTENDUP BEHIND FLASHINGNO. 2 76 MM (3") MIN.
NOTE:DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
does not violate Dryvit's warranty. This detail is subject to change
APPROVED BY:
®REV: DATE:
4RS 02/09
without notice. Contact Dryvit to insure you have the most recent version.
1.
3. REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATION OPTIONS.
and Dryvit specifically disclaims any liability for the use of
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
REFER TO OSMD DETAIL 0.0.30 FOR DECKCUTAWAY DETAIL.
Dryvit products is the responsibility of the project's design
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
The architecture, engineering and design of the project using the 2.
CODE APPROVED WATER-RESISTIVE BARRIER
SUBSTRATE
Outsulation SMD System Wood Framed Deck - Cross Section
DRYVIT MD SPACER
DRAINAGE TRACK
DRYVIT FINISH
DECK FRAMINGFLASHING NO. 2 EXTEND UP BEHIND
FLASHING NO. 3 76 MM (3") MIN.
25 MM (1") MIN.
64 MM (2-1/2") MIN.
FLASHING NO. 3 EXTENDUP BEHIND INSULATION
BOARD 76 MM (3")
SUPPORT STRIP
DECK BOARDS51 MM (2") MIN.
OSMD 0.0.29APPROVED OSMD SYSTEMINSULATION BOARDCODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
DRYVIT MD SPACER™LAPPED OVER FLANGE
OF DRAINAGE TRACK
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
® ™
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
The architecture, engineering and design of the project using the
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
Wood Framed Deck - Cut AwayNOTE:
DRYVIT RECOMMENDS THAT GROUND FLOORAPPLICATIONS AND ALL FACADES EXPOSEDTO ABNORMAL STRESS, HIGH TRAFFIC, ORDELIBERATE IMPACT HAVE THE BASE COATREINFORCED WITH PANZER® MESH PRIORTO STANDARD MESH™ OR STANDARD PLUSMESH™. LOCATION OF HIGH IMPACT ZONESSHOULD BE INDICATED ON CONTRACTDRAWINGS.
REV:APPROVED BY: DATE:
4RS 02/09
version.
1. REFER TO OSMD DETAIL 0.0.29 FOR DECK-CROSS SECTION DETAIL.
2.
Outsulation SMD System
®
OSMD 0.0.30
DRAINAGE TRACK
OSMD SYSTEM
END JOIST
FLASHING NO. 3 TURNEDDOWN OVER END JOIST
WOOD DECK BOARD
FLASHING NO. 1
DRYVIT COMPATIBLESEALANT, BY OTHERS
FLASHING NO. 2 BEHINDAPPROVED OSMD BOARD
(HIDDEN)
® ™
NOTE:
does not violate Dryvit's warranty. This detail is subject to change
®REV:APPROVED BY: DATE:
4RS 02/09
version.without notice. Contact Dryvit to insure you have the most recent
and Dryvit specifically disclaims any liability for the use of
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
1.
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
Outsulation SMD System Soffit Termination
SUBSTRATE
WOOD OR STEEL FRAMINGCODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT MD SPACER
12.7 MM (1/2") MIN.DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATAPPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT FINISH
WRAP DRYVIT DETAIL MESH® 51 MM (2") MIN.AT BACKSIDE OF INSULATION BOARD
DRYVIT COMPATIBLE SEALANT WITHCLOSED CELL BACKER ROD, BY OTHERS
OSMD 0.0.31
ROOF ASSEMBLY
® ™
™
SUBSTRATE
CODE APPROVED WATER-RESISTIVE BARRIERDRYVIT MD SPACER
NOTE:
does not violate Dryvit's warranty. This detail is subject to change
APPROVED BY:
®REV: DATE:
4RS 02/09
without notice. Contact Dryvit to insure you have the most recent version.
INSTALL SOFFIT FRIEZE BOARD AND TRIMAFTER OSMD SYSTEM IS IN PLACE.
1.
and Dryvit specifically disclaims any liability for the use of
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENERS MUST BE INSTALLED INTO THEFRAMING. standards. This detail is for general information and guidance only
professional. All systems must comply with local building codes and Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the 2.
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COATDRYVIT FINISH
Outsulation SMD System Soffit With Frieze Board
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,BY OTHERS
12.7 MM (1/2") MIN.
DRYVIT DEMANDIT®OR COLOR PRIME™ON SURFACE(S) TO RECEIVE SEALANT
SPACER BLOCK
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
38 MM (1-1/2") MIN.
DRYVIT COMPATIBLE SEALANT WITHBOND BREAKER, BY OTHERS
FRIEZE BOARD
OSMD 0.0.32
ROOF ASSEMBLY
® ™
™
CODE APPROVED WATER-RESISTIVE BARRIERDRYVIT MD SPACER
GABLE END RAFTER
NOTE:
this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole
standards. This detail is for general information and guidance only professional. All systems must comply with local building codes and
and Dryvit specifically disclaims any liability for the use of
Dryvit products is the responsibility of the project's design
without notice. Contact Dryvit to insure you have the most recent
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
discretion, whether this detail or a functionally equivalent alternative
The architecture, engineering and design of the project using the
REV:APPROVED BY: DATE:
RS 4 02/09
version.
FOR RAKE WITH OVERHANG REFER TOOSMD DETAIL 0.0.32.
FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENER MUST BE INSTALLED INTO THEFRAMING.
1. 2.
®
Gable End With EIFS Trim
APPROVED OSMD SYSTEM INSULATION BOARD
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
Outsulation SMD System
ROOF SHINGLES
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
64 MM (2-1/2") MIN.
DRYVIT COMPATIBLE SEALANTWITH BOND BREAKER, BY OTHERS
APPROVED OSMD SYSTEM INSULATION BOARD OR EPS TRIM (OPTIONAL)ADHERED WITH DRYVIT GENESIS,GENESIS DM OR GENESIS DMS BASECOAT OR MECHANICALLY FASTEN INTOSOLID SUBSTRATE
DRYVIT FINISH
DRIP EDGE FLASHING
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
SUBSTRATE
ROOFING PAPER
OSMD 0.0.33
SECTION A-A
® ™
™
CODE APPROVEDWATER-RESISTIVE BARRIER
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDE
OF INSULATION BOARD
DRYVIT COMPATIBLE SEALANTWITH CLOSED CELL BACKER ROD,
BY OTHERSDRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
NOTE:
without notice. Contact Dryvit to insure you have the most recent
DATE:
4RS 02/09
REV:APPROVED BY:
®
version.
and Dryvit specifically disclaims any liability for the use of
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
FOR NON-NAILABLE SHEATHING SUBSTRATES,THE FASTENER MUST BE INSTALLED INTO THEFRAMING.
FOR RAKE WITH OVERHANG REFER TOOSMD DETAIL 0.0.32.
1. 2.professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
Outsulation SMD System Gable End With Wood Trim
DRYVIT FINISH
DRYVIT MD SPACERAPPROVED OSMD SYSTEM INSULATIONBOARD
ROOF SHINGLES
GABLE END RAFTERWOOD TRIM BOARD
38 MM (1 1/2") MIN.
DRYVIT DEMANDIT® OR COLOR PRIME™ ON SURFACE(S) TO RECEIVE SEALANT
SPACER BLOCK
SEALANT WITH BONDBREAKER, BY OTHERS 64 MM (2 1/2") MIN.
DRYVIT COMPATIBLE SEALANTWITH BOND BREAKER, BY OTHERS
13 MM (1/2") MIN.
DRIP EDGE FLASHING
SUBSTRATE
ROOFING PAPER
OSMD 0.0.34
SECTION A-A
® ™
™
DRYVIT MD SPACER LAPPED OVERFLANGE OF DRAINAGE TRACK
CODE APPROVEDWATER-RESISTIVE BARRIER
NOTE:
without notice. Contact Dryvit to insure you have the most recent
4RS 02/09
REV:APPROVED BY: DATE:
®
version.
REFER TO DETAILS OSMD 0.0.01, 0.0.02 AND0.0.03 FOR SYSTEM CONFIGURATIONOPTIONS.
1.
this detail and for the architecture, design, engineering or workmanship
discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
of any project. The project design professional determines, in its sole
APPROVED OSMD INSULATION BOARD MAY NEEDTO BE NOTCHED TO ACCOMMODATEWATER-RESISTIVE BARRIER/ DRAINAGE MEDIUM.
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of
2. Dryvit products is the responsibility of the project's design The architecture, engineering and design of the project using the
Outsulation SMD System Termination at Parapet
DRAINAGE TRACK
DRYVIT COMPATIBLE SEALANTWITH BOND BREAKER, BY OTHERS
DRYVIT REINFORCING MESH EMBEDDEDIN DRYVIT GENESIS®, GENESIS DMOR GENESIS DMS BASE COAT
ROOF ASSEMBLY
203 MM (8") MIN.
DRYVIT MD SPACERDrainage TrackOption
CODE APPROVEDWATER-RESISTIVE BARRIER
SUBSTRATE
ROOF FLASHING ANDCOUNTERFLASHING
WOOD OR STEEL FRAMINGAPPROVED OSMD SYSTEMINSULATION BOARD
DRYVIT FINISH
DRYVIT COMPATIBLESEALANT, BY OTHERS
OSMD 0.0.35
WRAP DRYVIT DETAIL MESH®51 MM (2") MIN. AT BACKSIDEOF INSULATION BOARD
DRYVIT APPROVED WASHER WITHCORROSION RESISTANT FASTENER
64 MM (2 1/2") MIN.
METAL CAP FLASHING
® ™
™
FASCIADRIP EDGE
SOLDER ALL JOINTSIN KICKOUT DIVERTER
Termination at Roof to Wall Flashing
discretion, whether this detail or a functionally equivalent alternative
does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail
without notice. Contact Dryvit to insure you have the most recent
Dryvit products is the responsibility of the project's design
and Dryvit specifically disclaims any liability for the use of
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only
of any project. The project design professional determines, in its sole this detail and for the architecture, design, engineering or workmanship
The architecture, engineering and design of the project using the NOTE:
EXTEND ROOFING PAPER 127 MM (5") MIN.UP VERTICAL WALL BEHIND METALFLASHING.
4RS 02/09
APPROVED BY: REV: DATE:
version.
METAL FLASHINGS ARE 254 MM (10") X 51 MM(2") LONGER THAN THE EXPOSED PORTION OFTHE ROOFING SHINGLE AND ARE BENT IN HALFTO ALLOW FOR TWO 127 MM (5") LEGS.ALTHOUGH NOT SHOWN, METAL FLASHINGS ARESTEP FLASHED (INTERWOVEN) WITH ROOFINGSHINGLES.
KICKOUT DIVERTER TO BE MADE FROMCORROSION RESISTANT MATERIAL MIN. 24GAGE.
3.
EXTEND KICKOUT A MINIMUM OF 25 MM (1")BEYOND FACE OF SYSTEM.
2.
1. 4.
Outsulation SMD System
®
DRYVIT MD SPACER 152 MM(6")
CODE APPROVED WATER-RESISTIVEBARRIER LAPPED OVER FLASHING
ROOF SHINGLESROOFING PAPER(SEE NOTE 3)
METAL FLASHING, BY OTHERS(SEE NOTE 4)
DRYVIT COMPATIBLESEALANT, BY OTHERS
APPROVED OSMD SYSTEMINSULATION BOARD
50MM (2") MIN.
KICKOUT DIVERTER
OSMD 0.0.36
152 MM(6")
110
100
303 MM(12")
® ™
™
REFER TO DETAILS OSMD 0.0.01,0.0.02 AND 0.0.03 FOR SYSTEMCONFIGURATION OPTIONS.
1. The architecture, engineering and design of the project using the
without notice. Contact Dryvit to insure you have the most recent
DATE:
02/094RS
REV:APPROVED BY:
®
version.
this detail and for the architecture, design, engineering or workmanship
is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change
of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative
professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of
Dryvit products is the responsibility of the project's design
Outsulation SMD SystemNOTE:
Chimney Enclosure
CRICKET FLASHING
CODE APPROVED WATER-RESISTIVEBARRIER OVER SUBSTRATE
STEP FLASH ROOFING SHINGLESAND METAL FLASHING
DIVERTER FLASHING(SEE DETAIL OSMD 0.0.36)
DRYVIT COMPATIBLESEALANT, BY OTHERS
50 MM (2") MIN. CLEARANCEBETWEEN OSMD
SYSTEM AND SHINGLES DRAINAGE STRIP
ROOFING SHINGLES
SEAL BETWEEN METAL CAP ANDDRYVIT SYSTEM USING DRYVIT
COMPATIBLE SEALANT WITHBOND BREAKER, BY OTHERS
SUBSTRATE
OSMD SYSTEM
TERMINAL RAIN CAP
OSMD 0.0.37
® ™