Your Windoware Outdoor Screen Roller Blind comes complete with all parts and fixing accessories for a quick and easy installation. The only tools you will require are a 1/8” drill bit, a Phillips Head screwdriver, tape measure and a pencil. Note: The screws provided are for use with timber only. Please see your dealer for recommendations when installing your blind against other materials. STEP 1 Mark the holes where the screws will go. Use the table (Fig.1) to determine how far apart the brackets will be for your size roller. STEP 2 Screw the Idle Plug unit and Clutch unit into place. The Clutch unit will go on the right while the Idle Plug unit will go on the left. Do not tighten screws completely. STEP 3 Insert the Clutch plug into the clutch unit. While holding the roller, insert the other side (Idle End plug) into the Idle Plug unit. It should snap into place with a bit of pressure. Adjust brackets for a snug fit. Tighten screws to lock both brackets in place. STEP 4 Install the Tension Device. Feed the chain through the pulley as shown. Position the base so that the cord is taut and operable but not loose. It should only have enough slack to operate when pulled up or down, do not twist or slant the chain. Screw the base into place. Click the cover over the base and screw in place. STEP 5 Install the Tie Downs (Optional). This is used to secure your roller in light breezes. Remove the end caps from the bottom rail. Slide the Tie Downs into the groove, once this is done replace the end caps. You will need something to anchor the Tie Downs to such as a hook which should be sourced seperately from your hardware store. furnishing solutions with style! INSTALLATION INSTRUCTIONS OUTDOOR SCREEN ROLLER BLIND FABRIC WIDTH SCREW TO SCREW measurement 1.2m 1225mm 1260mm 1.5m 1525mm 1560mm 1.8m 1825mm 1860mm 2.1m 2125mm 2160mm 2.4m 2425mm 2460mm TOTAL WIDTH after installation Clutch unit Tension device base cover Tie Down Bottom rail Idle Plug unit Clutch plug Idle end plug (Fig.1) WARNING: Blind Cords may create a strangulation hazard for young children. KEEP BLIND CORDS OUT OF REACH OF CHILDREN. To avoid creating a possible strangulation hazard for children, the corded internal window covering must be installed in such a way that a loose cord cannot form a loop 220mm or longer at a height of less than 1600mm above floor level. - A cord guide may be installed lower than 1600mm above floor level if the cord is sufficiently secured or tensioned to prevent a loop 220mm or longer from being formed. - If a cord guide is installed lower than 1600mm above floor level it must be designed to prevent a child from being able to remove the cord. - If a cleat is used to secure the cord it must be at least 1600mm above floor level because a child is capable of unwinding a cord from a cleat.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Your Windoware Outdoor Screen Roller Blind comes complete with all parts and fixing accessories for a quick and easy installation. The only tools you will require are a 1/8” drill bit, a Phillips Head screwdriver, tape measure and a pencil.
Note: The screws provided are for use with timber only. Please see your dealer for recommendations when installing your blind against other materials.
STEP 1Mark the holes where the screws will go. Use the table (Fig.1) to determine how far apart the brackets will be for your size roller.
STEP 2Screw the Idle Plug unit and Clutch unit into place. The Clutch unit will go on the right while the Idle Plug unit will go on the left. Do not tighten screws completely.
STEP 3Insert the Clutch plug into the clutch unit. While holding the roller, insert the other side (Idle End plug) into the Idle Plug unit. It should snap into place with a bit of pressure. Adjust brackets for a snug fit. Tighten screws to lock both brackets in place.
STEP 4Install the Tension Device. Feed the chain through the pulley as shown. Position the base so that the cord is taut and operable but not loose. It should only have enough slack to operate when pulled up or down, do not twist or slant the chain. Screw the base into place. Click the cover over the base and screw in place.
STEP 5Install the Tie Downs (Optional).This is used to secure your roller in light breezes. Remove the end caps from the bottom rail. Slide the Tie Downs into the groove, once this is done replace the end caps. You will need something to anchor the Tie Downs to such as a hook which should be sourced seperately from your hardware store.
furnishing solutions with style!
InSTallaTIon InSTrucTIonSouTdoor ScrEEn rollEr blInd
FabrIcWIdTH
ScrEW To ScrEWmeasurement
1.2m 1225mm 1260mm1.5m 1525mm 1560mm1.8m 1825mm 1860mm2.1m 2125mm 2160mm2.4m 2425mm 2460mm
ToTal WIdTHafter installation
clutch unit
Tension device base cover
Tie downbottom rail
Idle Plug unit
clutch plug
Idle end plug
(Fig.1)
WarnInG:blind cords may create a strangulation hazard for
young children.KEEP blInd cordS ouT
oF rEacH oF cHIldrEn.
To avoid creating a possible strangulation hazard for children, the corded internal window covering must be installed in such a way that a loose cord cannot form a loop 220mm or longer at a height of less than 1600mm above floor level.- A cord guide may be installed lower than 1600mm above floor level if the cord is sufficiently secured or tensioned to prevent a loop 220mm or longer from being formed.- If a cord guide is installed lower than 1600mm above floor level it must be designed to prevent a child from being able to remove the cord.- If a cleat is used to secure the cord it must be at least 1600mm above floor level because a child is capable of unwinding a cord from a cleat.
furnishing solutions with style!
australia 02 9741 4099 new Zealand 64-3-366 9810
adJuST cHaIn TEnSIonTo adjust the tension in the chain you must first slide off the cover on the Clutch unit. Once it is off you will see four screws as shown below. To loosen the tension turn the screws anti-clockwise. To tighten the tension turn the screws clockwise.
adJuSTInG For a lEFT HandEd cHaIn conTrolTo make the chain operate on the left hand side, begin by sliding the cover off the Clutch unit. You will expose four screws used for adjusting the tension. Unscrew these to access the inner chain apparatus as shown below. Turn this 180 degrees so the chain can hang from the left side. Replace the screws and cover. There is no need to do anything to the Idle plug unit. Lastly, pull out the end plugs on the tube and switch them around.
adJuSTInG For cEIlInG InSTallaTIonTo make the chain operate from the top such as the ceiling you will need to make adjustments to both the Clutch unit and Idle plug unit. Slide the covers off both units and remove the screws. As we did before when adjusting the chain for left hand control turn the inner chain apparatus inside the Clutch unit 90 degrees so it will hang down.
www.windoware.com.au
WarnInG:We strongly recommend
that in strong wind conditions, you
completely retract your Outdoor Screen Roller
Blind to prevent damage to it and your windows.
down
downclutch unit-remove screws
Idle Plug unit-remove screws
In the Idle plug unit, once you have removed the screws as shown below, you will see the inner apparatus which holds the end plug in place. Turn this so the opening is facing down or away from the ceiling. Once this is done, replace the screws and covers for both units and proceed with installation.
Related Documents
