2015-08-12 1 2015-08-12 OSRAM OSTAR Projection Power Datasheet Version 1.4 LE CG P3W OSRAM OSTAR Projection Power is a high luminance LED for projection applications. Die OSRAM OSTAR Projection Power ist eine LED mit hoher Leuchtdichte für Projektionsanwendungen. Features: Besondere Merkmale: • Package: OSTAR High Power Projection • Gehäusetyp: OSTAR High Power Projection • Technology: ThinGaN • Technologie: ThinGaN • Viewing angle at 50 % I V : 130° • Abstrahlwinkel bei 50 % I V : 130° • Color: Cx = 0.32, Cy = 0.64 acc. to CIE 1931 (converted green) within λ = 500 ... 600 nm; 0.32 / 0.54 for full spectral range • Farbe: Cx = 0.32, Cy = 0.64 nach CIE 1931 (konvertiertes Grün) im Bereich λ = 500 ... 600 nm; 0.32 / 0.54 für den gesamten Spektralbereich • Corrosion Robustness: Improved corrosion robustness • Korrosionsstabilität: Verbesserte Korrosionsstabilität Applications Anwendungen • Projection • Projektion
25
Embed
OSRAM OSTAR Projection Power Datasheet Version … · 2015-08-12 1 2015-08-12 OSRAM OSTAR Projection Power Datasheet Version 1.4 LE CG P3W OSRAM OSTAR Projection Power is a high …
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
2015-08-12 1
2015-08-12
OSRAM OSTAR Projection Power
Datasheet
Version 1.4
LE CG P3W
OSRAM OSTAR Projection Power is a high luminance LED for projection applications.
Die OSRAM OSTAR Projection Power ist eine LED mit hoher Leuchtdichte für Projektionsanwendungen.
Features: Besondere Merkmale:
• Package: OSTAR High Power Projection • Gehäusetyp: OSTAR High Power Projection• Technology: ThinGaN • Technologie: ThinGaN • Viewing angle at 50 % IV: 130° • Abstrahlwinkel bei 50 % IV: 130°• Color: Cx = 0.32, Cy = 0.64 acc. to CIE 1931
(converted green) within λ = 500 ... 600 nm; 0.32 / 0.54 for full spectral range
• Farbe: Cx = 0.32, Cy = 0.64 nach CIE 1931 (konvertiertes Grün) im Bereich λ = 500 ... 600 nm; 0.32 / 0.54 für den gesamten Spektralbereich
ΔVF = VF - VF(25 °C) = f(Tj); IF = 6000 mA; per Chip
Relative Luminous Flux 7) page 24
Relativer Lichtstrom 7) Seite 24
ΦV/ΦV(25 °C) = f(Tj); IF = 6000 mA; per Chip
-40-0.3
˚CTj
OHL04428
VFV∆
-20 0 20 40 60 80 120
-0.2
-0.1
0
0.1
0.2
0.3
-40 -20 0 20 40 60 80 100 120
Tj [°C]
0,0
0,2
0,4
0,6
0,8
1,0
ΦV
ΦV (25°C)
Version 1.4 LE CG P3W
2015-08-12 13
Chromaticity Coordinate Shift 7) page 24
Farbortverschiebung 7) Seite 24
ΔCx, ΔCy = f(Tj); IF = 6000 mA; per Chipwithin λ = 500 ... 600 nm
Chromaticity Coordinate Shift 7) page 24
Farbortverschiebung 7) Seite 24
ΔCx, ΔCy = f(Tj); IF = 6000 mA; per Chipfull spectral range
-40 -20 0 20 40 60 80 100 120
Tj [°C]
-0,03
-0,02
-0,01
0,00
0,01
0,02
0,03∆Cx; ∆Cy
: Cx
: Cy
-40 -20 0 20 40 60 80 100 120
Tj [°C]
-0.03
-0.02
-0.01
0.00
0.01
0.02
0.03∆Cx; ∆Cy
: Cx
: Cy
OHL05134
2015-08-12 14
Version 1.4 LE CG P3W
Max. Permissible Forward Current
Max. zulässiger Durchlassstrom
IF = f (T)LE T P3W
0 20 40 60 80
TB [°C]
0
500
1000
1500
2000
2500
3000
IF [mA]
Do not use below 200 mA
Version 1.4 LE CG P3W
2015-08-12 15
Package Outline 8) page 24
Maßzeichnung 8) Seite 24
Approximate Weight: 37.0 g
Gewicht: 37.0 g
Connector Housing: Molex 12ckt Micro Fit 3.0 Harness Connector, right angle DR; P/N 43045-1210 (see also www.molex.de) Pin: Molex Micro Fit 3.0, Crimp Terminal, Male, Au plated; P/N 43031-0003 (see also www.molex.de)
Stecker Gehäuse: Molex 12ckt Micro Fit 3.0 Harness Connector, right angle DR; P/N 43045-1210 (see also www.molex.de) Stecker: Molex Micro Fit 3.0, Crimp Terminal, Male, Au plated; P/N 43031-0003 (see also www.molex.de)
Recommended mating connector Housing: Molex 12ckt Micro Fit 3.0, receptacle housing, DR; P/N 43045-1200 (see also www.molex.de) Pin: Molex Micro Fit 3.0, Crimp Terminal, Female, Au plated; P/N 43030-0003 (see also www.molex.de)
Empfohlener Gegenstecker Gehäuse: Molex 12ckt Micro Fit 3.0, receptacle housing, DR; P/N 43045-1200 (see also www.molex.de) Stecker: Molex Micro Fit 3.0, Crimp Terminal, Female, Au plated; P/N 43030-0003 (see also www.molex.de)
2015-08-12 16
Version 1.4 LE CG P3W
Corrosion robustness: Test conditions: 40 °C / 90 % rh / 15 ppm H2S / 336 h = Stricter than IEC 60068-2-43 (H2S) [25°C / 75 % rh / 10 ppm H2S / 21 days] = Regarding relevant gas (H2S) stricter than EN 60068-2-60 (method 4) [25 °C / 75 % rh / 200 ppb SO2, 200 ppb NO2,10 ppb Cl2 / 21 days]
Korrosionsfestigkeit: Test Kondition: 40°C / 90 % rh / 15 ppm H2S / 336 h = Besser als IEC 60068-2-43 (H2S) [25°C / 75 % rh / 10 ppm H2S / 21 Tage] = Bezogen auf das Gas (H2S) besser als EN 60068-2-60 (method 4) [25°C / 75 % rh / 200ppb SO2, 200ppb NO2,10ppb Cl2 / 21 Tage]
Note: Package not suitable for any kind of wet cleaning or ultrasonic cleaning.
Anm.: Das Gehäuse ist für alle Arten einer nasschemischen Reinigung oder Ultraschallreinigung nicht geeignet.
Data Matrix Code Description
Data Matrix Code Beschreibung
The Data Matrix Code bin information is Laser marked during testing
Content: aaaa@bbbb@ccc@ddddd@eeeee
Data Matrix Code Type: ECC200
a = Luminous Flux (Phiv) [lm] or Radiant Flux (Phie) [W] (example: 3306)
b = Forward Voltage (Vf ) [V] (example: 3.46)
c = Wavelength (Ldom) [nm] (example: 618)
d = Color Coordinate Cx (example: 0.321)
e = Color Coordinate Cy (example: 0.641)
@: Seperator = Blank
Die Bin -Information auf dem Datamatrix Code wird während des Testens geschrieben
Inhalt: aaaa@bbbb@ccc@ddddd@eeeee
Data Matrix Code Typ: ECC200
a = Lichtstrom (Phiv) [lm] oder Strahlleistung (Phie) [W] (Beispiel: 3306)
b = Vorwärtsspannung (Vf ) [V] (Beispiel: 3.46)
c = Wellenlänge (Ldom) [nm] (Beispiel: 618)
d = Farbkoordinate Cx (Beispiel: 0.321)
d = Farbkoordinate Cy (Beispiel: 0.641)
@: Platzhalter = Leerzeichen
Version 1.4 LE CG P3W
2015-08-12 17
Electrical Internal Circuit
Internes Elektrisches Schaltbild
2015-08-12 18
Version 1.4 LE CG P3W
Pin - Asignment
Anschlussbelegung
Pin / Anschluss Description / Function / Beschreibung /
Funktion
1 NTC
2 common Anode, NTC
3 common Anode, NTC
4 common Anode, NTC
5 common Anode, NTC
6 common Anode, NTC
7 Cathode; Chip 3
8 Cathode; Chip 2
9 Cathode; Chip 1
10 Cathode; Chip 6
11 Cathode; Chip 5
12 Cathode; Chip 4
Version 1.4 LE CG P3W
2015-08-12 19
Tray
Bauteilträger
12 pcs. per tray
Barcode-Tray-Label (BTL)
Barcode-Tray-Etikett (BTL)
MATERIAL: Material Number Batch Batch Number
OHA02684
DC:LE xxx xxx Group: xxxx-xxxx-xxxx Date CodeDataMatrixCode
BIN
BIn N
r.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLEBatch Number
EXAMPLE
EXAMPLE
EXAMPLEBatch NumberBatch Number
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLEBatch Number
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLEBatch
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLEBatchBatch
xxxx-xxxx-xxxxxxxx-xxxx-xxxxEXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Group: xxxx-xxxx-xxxxEXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Group:Group:EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
xxxx-xxxx-xxxxEXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Group:EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
LE xxx xxxEXAMPLE
EXAMPLE
EXAMPLE
Group:EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
LE xxx xxxLE xxx xxxEXAMPLEBatch NumberBatch NumberBatch
The evaluation of eye safety occurs according to the standard IEC 62471:2008 ("photobiological safety of lamps and lamp systems"). Within the risk grouping system of this CIE standard, the LED specified in this data sheet fall into the class Moderate risk (exposure time 0.25 s). Under real circumstances (for exposure time, eye pupils, observation distance), it is assumed that no endangerment to the eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential due to their blinding effect. As is also true when viewing other bright light sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irritation, annoyance, visual impairment, and even accidents, depending on the situation.
Die Bewertung der Augensicherheit erfolgt nach dem Standard IEC 62471:2008 ("photobiological safety of lamps and lamp systems"). Im Risikogruppensystem dieser CIE- Norm erfüllen die in diesem Datenblatt angegebenen LEDs folgende Gruppenanforderung - Moderate risk (Expositionsdauer 0,25 s). Unter realen Umständen (für Expositionsdauer, Augenpupille, Betrachtungsabstand) geht damit von diesen Bauelementen keinerlei Augengefährdung aus. Grundsätzlich sollte jedoch erwähnt werden, dass intensive Lichtquellen durch ihre Blendwirkung ein hohes sekundäres Gefahrenpotenzial besitzen. Nach einem Blick in eine helle Lichtquelle (z.B. Autoscheinwerfer), kann ein temporär eingeschränktes Sehvermögen oder auch Nachbilder zu Irritationen, Belästigungen, Beeinträchtigungen oder sogar Unfällen führen.
Subcomponents of this LED contain, among other substances, goldplated and Ag-filled materials. In spite of the improved corrosion stability of this LED, it can be affected by environments that contain very high concentrations of aggressive substances. Therefore, we recommend avoiding aggressive atmospheres during storage, production and use.
Einzelkomponenten dieser LED enthalten u.a. goldbeschichtete und Ag-gefüllte Materialien. Trotz der verbesserten Korrosionsstabilität dieser LED können Einzelkomponenten durch sehr hohe Konzentration aggressiver Substanzen angegriffen werden. Aus diesem Grund wird empfohlen, aggressive Umgebungen während der Lagerung, Produktion und im Betrieb zu vermeiden.
2015-08-12 22
Version 1.4 LE CG P3W
Disclaimer Disclaimer
Language english will prevail in case of any discrepancies or deviations between the two language wordings.
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet.Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred.Components used in life-support devices or
systems must be expressly authorized for such
purpose!
Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS.
*) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system.**) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered.
Bei abweichenden Angaben im zweisprachigen Wortlaut haben die Angaben in englischer Sprache Vorrang.
Bitte beachten!
Lieferbedingungen und Änderungen im Design vorbehalten. Aufgrund technischer Anforderungen können die Bauteile Gefahrstoffe enthalten. Für weitere Informationen zu gewünschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet.Verpackung
Benutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nächstgelegene Vertriebsbüro. Wir nehmen das Verpackungsmaterial zurück, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Für Verpackungsmaterial, das unsortiert an uns zurückgeschickt wird oder das wir nicht annehmen müssen, stellen wir Ihnen die anfallenden Kosten in Rechnung.Bauteile, die in lebenserhaltenden Apparaten und
Systemen eingesetzt werden, müssen für diese
Zwecke ausdrücklich zugelassen sein!
Kritische Bauteile* dürfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverständnis von OSRAM OS vorliegt.
*) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems führen wird oder die Sicherheit oder Effektivität dieses Apparates oder Systems beeinträchtigt.**) Lebenserhaltende Apparate oder Systeme sind für (a) die Implantierung in den menschlichen Körper oder (b) für die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist.
Version 1.4 LE CG P3W
2015-08-12 23
Glossary Glossar
1) Brightness: Brightness values are measured during a pulse train of 100 ms with a pulse width of 500 µs and a frequencey of 1 kHz, with an internal reproducibility of +/- 8 % and an expanded uncertainty of +/- 11 % (acc. to GUM with a coverage factor of k = 3). The peak brightness is calculated according to the pulse duration and frequency.
1) Helligkeit: Helligkeitswerte werden während einer Pulsfolge der Dauer 100 ms mit einer Pulsbreite von 500 µs bei einer Frequenz von 1 kHz gemessen, mit einer internen Reproduzierbarkeit von +/- 8 % und einer erweiterten Messunsicherheit von +/- 11 % (gemäß GUM mit Erweiterungsfaktor k = 3). Die Helligkeitswerte werden gemäß der Pulsdauer und Frequenz berechnet.
2) Chromaticity coordinate groups: Chromaticity coordinates are measured during a pulse train of 100 ms with a pulse width of 500 µs and a frequencey of 1 kHz , with an internal reproducibility of +/- 0,005 and an expanded uncertainty of +/- 0,01 (acc. to GUM with a coverage factor of k = 3).
2) Farbortgruppen: Farbkoordinaten werden während einer Pulsfolge der Dauer 100 ms mit einer Pulsbreite von 500 µs bei einer Frequenz von 1 kHz, mit einer internen Reproduzierbarkeit von +/- 0,005 und einer erweiterten Messunsicherheit von +/- 0,01 gemessen (gemäß GUM mit Erweiterungsfaktor k = 3).
3) Forward Voltage: The forward voltage is measured during a pulse of typical 500 µs, with an internal reproducibility of +/- 0,05 V and an expanded uncertainty of +/- 0,1 V (acc. to GUM with a coverage factor of k=3).
3) Durchlassspannung: Vorwärtsspannungen werden während eines Strompulses einer typischen Dauer von 500 µs, mit einer internen Reproduzierbarkeit von +/- 0,05 V und einer erweiterten Messunsicherheit von +/- 0,1 V gemessen (gemäß GUM mit Erweiterungsfaktor k=3).
4) Characteristic curve: In the range where the line of the graph is broken, you must expect higher differences between single LEDs within one packing unit.
4) Kennlinien: Im gestrichelten Bereich der Kennlinien muss mit erhöhten Abweichungen zwischen Leuchtdioden innerhalb einer Verpackungseinheit gerechnet werden.
5) Thermal Resistance: Rth max is based on statistic values (6σ).
5) Wärmewiderstand: Rth max basiert auf statistischen Werten (6σ).
2015-08-12 24
Version 1.4 LE CG P3W
6) NTC Thermistor: The R-T-Curve of an NTC thermistor can be described by an exponential relation within the range of the application temperature. For a more detailed description of the R/T dependency please consult the manufacturers datasheet (www.murata.com).
6) NTC Thermistor: Die R-T-Kurve eines NTC Thermistors lässt sich innerhalb des für die Anwendung spezifizierten Temperaturbereichs durch einen exponentiellen Zusammenhang beschreiben. Für eine genauere Beschreibung der R-T-Abhängigkeit sollte das Datenblatt des Herstellers herangezogen werden (www.murata.com).
7) Typical Values: Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice.
7) Typische Werte: Wegen der besonderen Prozessbedingungen bei der Herstellung von LED können typische oder abgeleitete technische Parameter nur aufgrund statistischer Werte wiedergegeben werden. Diese stimmen nicht notwendigerweise mit den Werten jedes einzelnen Produktes überein, dessen Werte sich von typischen und abgeleiteten Werten oder typischen Kennlinien unterscheiden können. Falls erforderlich, z.B. aufgrund technischer Verbesserungen, werden diese typischen Werte ohne weitere Ankündigung geändert.
8) Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and dimensions are specified in mm.
8) Maßtoleranz: Wenn in der Zeichnung nicht anders angegeben, gilt eine Toleranz von ±0,1. Maße werden in mm angegeben.