Original BMW Accessories. Installation Instructions.... · 2019. 2. 27. · Original BMW Accessories. Installation Instructions. 9/2012 M Aerodynamic Package Retrofit BMW 3 Series
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Original BMW Accessories.Installation Instructions.
M Aerodynamic Package RetrofitBMW 3 Series Saloon (F 30)BMW 3 Series Touring (F 31)
Retrofit kit number51 95 2 318 192 Basic package
Front bumper trim51 11 8 055 819 Primed front bumper trim51 11 8 055 820 Primed front bumper trim (for cars with SA 508)51 11 8 055 821 Primed front bumper trim (for cars with SA 508, SA 5DL and SA 5DP)51 11 8 055 822 Primed front bumper trim (for cars with SA 502 and SA 508)51 11 8 055 823 Primed front bumper trim (for cars with SA 502)51 11 8 055 824 Primed front bumper trim (for cars with SA 502, SA 508, SA 5DP and SA 5DL)
Front bumper trim for US vehicles51 11 8 055 825 Primed front bumper trim51 11 8 055 826 Primed front bumper trim (for cars with SA 508)51 11 8 055 827 Primed front bumper trim (for cars with SA 508, SA 5DL and SA 5DP)51 11 8 055 828 Primed front bumper trim (for cars with SA 502 and SA 508)51 11 8 055 829 Primed front bumper trim (for cars with SA 502)51 11 8 055 830 Primed front bumper trim (for cars with SA 502, SA 508, SA 5DP and SA 5DL)
Rear bumper trim for F30 cars51 12 8 056 497 Primed rear bumper trim51 12 8 056 498 Primed rear bumper trim (for cars with SA 507 and SA 508)
Rear bumper trim for F31 cars51 12 8 056 577 Primed rear bumper trim51 12 8 056 578 Primed rear bumper trim (for cars with SA 507 and SA 508)
Rear panel51 12 8 054 197 Rear bumper finisher (for cars with N13 or N47N engine)51 12 8 054 198 Rear bumper finisher (for cars with N20, N26, N47S1, N57N or N57Z engine)51 12 8 054 501 Rear bumper finisher (for cars with N55 or N56 engine)
Installation timeThe installation time is approx. 6 hours. This may vary depending on the condition of the car and the equipment in it.
The time required for painting is around 6 hours. The time specified for painting is a guideline time only. A 2-coat paint job with paint stage 2 was used as the basis for this guideline figure. The actual time spent on painting must be calculated based on the features and condition of the car, the layers of paint and the paint stage required. The total costs of the painting time must be taken into account when calculating the retrofitting costs.
Important informationThese installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, wiring diagrams, servicing manuals and work instructions, in a rational order, using the prescribed tools (special tools) and observing current health and safety regulations.
If you experience installation or function problems, restrict troubleshooting to approx. 0.5 hours for mechanical work and 1.0 hour for electrical work.
To avoid unnecessary extra work and/or costs, send an inquiry straight away to the technical parts support team via the Aftersales Assistance Portal (ASAP).
Quote the following information:
- Chassis number,
- retrofit kit part number,
- a detailed description of the problem,
- any work already carried out.
Do not archive the hard copy of these installation instructions since daily updates are provided via ASAP!
PictogramsDenotes instructions that draw your attention to dangers.
Denotes instructions that draw your attention to special features.
Denotes the end of the instruction or warning text.
Installation informationEnsure that the cables and/or lines are not kinked or damaged as you install them in the car. Costs arising from this will not be reimbursed by BMW AG.
Some of the installation steps are shown only on the left-hand side of the car, proceed in the same way on the right-hand side of the car.
All pictures show LHD cars; proceed accordingly on RHD cars.
All retrofitted components must be at room temperature when they are being installed.
In order to avoid damage, all installation sites must be free of coarse dirt.
Painting instructionsCheck that all the parts fit accurately on the car before painting them. Primed parts must be pre-treated accordingly before painting.
The BMW painting instructions must be observed (see ISTA No. 99 00 ...).
Ordering instructionsFront bumper trim A is not included in the basic package and must be ordered separately on a vehicle-specific basis (see EPC for part number and further information).
Rear bumper finisher AS is not included in the basic package and must be ordered separately for the appropriate design of exhaust system (see EPC for part number and further information).
Rear bumper trim AR is not included in the basic package and must be ordered separately according to the car's features and equipment (see EPC for part number and further information).
List of special equipmentThe following special equipment must be taken into consideration when installing the retrofit kit:SA 502 Headlight cleaning systemSA 507 Park Distance Control (PDC) rearSA 508 Park Distance Control (PDC) front and rearSA 544 Active speed control with braking functionSA 5DF Active speed control with Stop&Go functionSA 5DL Surround ViewSA 5DP Parking Assistant
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all(all securing material is reused)
Front bumper trim (no longer required, existing PDC sensors, camera systems, high-pressure jets, fog lights, centre left and right radiator grille and support mount are reused) 51 11 156
ACC sensor (is reused) 66 31 006
Front shock absorber (no longer required) – – –
Support for upper front bumper trim (is reused) 51 11 050
Support for lower front bumper trim (no longer required) 51 11 060
Lower front left and right air guide (no longer required) – – –
Lower front air duct (no longer required) – – –
Deformation element for left and right bumper trim (no longer required) 51 11 770
Left and right centre radiator grilles (are reused) 51 13 001
Trim for cover on left and right side member (no longer required) 51 71 447
Rear bumper trim (no longer required, existing PDC sensors are reused)51 12 156
Reinforcement for rear bumper trim (no longer required) – – –
Only cars without ACCRemove the existing support mount (1) and sheet metal nuts (2) from the removed bumper trim and clip to bumper trim A.
Clip front centre grille W to front bumper trim A.
Only cars with fog lightsClip left air inlet grille S and right air inlet grille T to bumper trim A.
Only cars without fog lightsOn cars without fog lights, use left air inlet grille U and right air inlet grille V.
Only cars with ACCRemove the existing support mount (1) and sheet metal nuts (2) from the removed bumper trim and clip to bumper trim A.
Clip front centre grille X to bumper trim A. Convert the ACC sensor using mount Y (see ISTA 66 31 006).
Only cars with fog lightsClip left air inlet grille S and right air inlet grille T to bumper trim A.
Only cars without fog lightsClip left air inlet grille U and right air inlet grille V to bumper trim A.
Only cars with fog lightsInsert right mount AA into bumper trim A and secure with existing expanding rivet (1) and Torx screws Z. Insert existing sheet metal nuts (2) from the removed bumper into right-hand mount AA.
Insert fog lights (3) into right-hand mount AA and secure with the existing Torx screw (4).
Only cars without fog lightsUse left-hand mount AC and right-hand mount AD and secure as described above.
Only cars with SA 508, SA 544, SA 5DF, SA 5DL or SA 5DPInstall existing PDC sensors into front bumper trim A (see ISTA 66 20 ...).
Install camera modules into front bumper trim A (see ISTA 66 53 030).
Install existing PDC sensors for parking assistant into front bumper trim A (see ISTA 66 33 010)
Install ACC sensor into front bumper trim A (see ISTA 66 31 006).
Only cars with SA 502Convert the high-pressure jets (1) (see ISTA 61 67 100).
Connect the existing hose line (2) to the high-pressure jets (1).
Only cars with swapped-out engine oil coolerThe arrangement of the air ducts must be observed according to the engine and country version. The in-
stallation process is shown only on the right-hand side of the car; proceed in the same way on the left-hand side of the car.
Depending on the engine and country version, install right engine oil cooler air duct AE or left engine oil cooler air duct AF together with right engine oil cooler air duct AG using existing fastening material.
All carsInstall front bumper trim A using the existing fastening material and expanding rivet X (see ISTA 51 11 156).
Only cars with SA 502Clip left spray jet finisher AH and right spray jet finisher AI to front bumper trim A.
All carsStick badge AJ in front bumper trim A (see ISTA 51 14 001).
Clip the existing left and right radiator grilles (1) to front bumper trim A.
Install registration plate holder AK or AL using the existing fastening material.
Clip the towing eyelet finisher (2) to front bumper trim A.