ORBU-SPC-44-0-22

Page 1 of 13

OIL RECOVERY BUSINESS UNIT SPECIFICATION

ORBU-SPC-44-0-22

PIPING MATERIAL

Rev.# Date Description Originator Checked Approved Approved Client0 2004-01-14 ISSUED FOR IMPLEMENTATION QC TR EB KAM / BK TG

ORBU-SPC-44-0-22

REV 0 2004-01-14ENCANA CORPORATIONOIL RECOVERY BUSINESS UNIT SPECIFICATIONS

PIPING MATERIAL Page 2 of 13

TABLE OF CONTENTS

1.0 GENERAL1.1 Scope1.2 Definitions1.3 References1.4 Conflicts

2.0 MATERIALS2.1 General2.2 Pipe2.3 Valves2.4 Fittings2.5 Flanges2.6 Spectacle Blinds2.7 Gaskets2.8 Bolting2.9 Branch Connections

3.0 SERVICE CLASS INDEX

4.0 PIPING CLASSIFICATION LIST

5.0 SOUR SERVICE REQUIREMENTS5.1 General5.2 Material

6.0 MATERIAL IDENTIFICATION

7.0 HANDLING AND SHIPMENT7.1 General7.2 Pipe7.3 Flanges and Fittings7.4 Valves

APPENDIX 1 – PIPING CLASSIFICATIONS

APPENDIX 2 – NON-DESTRUCTIVE EXAMINATION

APPENDIX 3 – BRANCH CONNECTIONS

ORBU-SPC-44-0-22



1.0 GENERAL

1.1 Scope

1.1.1 This specification describes the commodity codes, line classes and the minimum materialrequirements for the construction and maintenance of piping systems for the Owner’s OilRecovery Business Unit.

1.2 Definitions

1.2.1 Seller: The entity, manufacturer, fabricator, vendor or contractor that supplies the materialor services.

1.2.2 Client: The company or companies for whom the Engineering Contractor is performing thework.

1.3 References

1.3.1 The following codes and standards shall be complied with as a minimum requirementexcept as modified in this specification. The latest issue, revision, or amendment of thereferenced standards in effect on the date of invitation to bid shall govern unless otherwisespecified.

1.3.1.1 ASME B1.20.1, Pipe Threads, General Purpose (Inch)1.3.1.2 ASME B16.5, Pipe Flanges and Flanged Fittings1.3.1.3 ASME B16.9, Factory-Made Wrought Steel Butt Welding Fittings1.3.1.4 ASME B16.11, Forged Fittings, Socket-Welding and Threaded1.3.1.5 ASME B16.20, Metallic Gaskets for Pipe Flanges – Ring Joint, Spiral – Wound

and Jacketed1.3.1.6 ASME B16.21, Nonmetallic Flat Gaskets for Pipe Flanges1.3.1.7 ASME B31.1, Power Piping1.3.1.8 ASME B31.3, Process Piping1.3.1.9 ASME B36.10M, Welded and Seamless Wrought Steel Pipe1.3.1.10 ASME B36.19M, Stainless Steel Pipe1.3.1.11 ASME Section II, Materials, Part A, B, C & D1.3.1.12 ASME Section V, Non-Destructive Examination1.3.1.13 ASME Section IX, Welding and Brazing Qualifications1.3.1.14 API standards as referenced herein1.3.1.15 ASTM material specifications as referenced herein1.3.1.16 PFI Standard ES241.3.1.17 NACE MR0175, Sulfide Stress Cracking Resistant Metallic Materials for Oilfield

Equipment1.3.1.18 Alberta Boilers Safety Association1.3.1.19 Safety Codes Act, Chapter S-0.51.3.1.20 Boilers and Pressure Vessels, Alberta Regulation 293/941.3.1.21 Design, Construction and Installation, Alberta Regulation 227/751.3.1.22 Gas Protection, Alberta Regulation 339/771.3.1.23 Mandatory Federal, Provincial or local regulations or codes in effect at the project

site1.3.1.24 All other standards, codes and specifications referred to directly or implied

throughout this specification.

ORBU-SPC-44-0-22



1.4 Conflicts

1.4.1 Where there are conflicts between the Engineering Contractor’s drawings, specifications orrequisitions and the specified code or governmental requirements, such conflicts shall bereferred to the Engineering Contractor in writing for resolution.

1.4.2 Any deviations from this specification shall be subject to approval in writing by theEngineering Contractor.

1.4.3 Abbreviations

Alt. Alternates NDE non destructive examinationANSI American National Standards N/A not applicable

Institute Ni nickelAARH arithmetic average root height NPS nominal pipe sizeASME The American Society of Mechanical NPT National Pipe Taper (thread)

Engineers OD outside diameterBW butt weld P phosphorousBE beveled end PE plain endBHN Brinell Hardness Number PFI Pipe Fabrication InstituteC carbon PQR Procedure Qualification RecordCA corrosion allowance psi pounds per square inchCE carbon equivalent P&ID Piping and InstrumentationConc concentric DiagramsCr chromium RF raised faceCRN Canadian Registration Number RJ ring jointCS carbon steel S sulfurCSA Canadian Safety Association Sch schedule of pipeCu copper Scrd. Screwedc/w complete with Se seleniumEcc eccentric Si SiliconEOL elbolet SMLS seamlessFNPT female National Pipe Taper (thread) SOL sockoletFPT female pipe thread SP Specialty Piping (item)FS forged steel SPWD spiral woundGALV galvanized SS stainless steelHAZ heat affected zone STD standardHRB Rockwell Hardness – B Scale SW socket weldHRC Rockwell Hardness – C Scale T tee (straight or reducing)ID inside diameter TE threaded endmax maximum temp temperaturemin minimum TOL Thredoletmm millimeters Va vanadiumMn manganese WN weld neckMTR material test report WPS Welding Procedure

SpecificationMNPT male National Pipe Taper (thread) WOL weldoletMo molybdenum XS extra strongMPT male pipe thread XXS double extra strong

ORBU-SPC-44-0-22



2.0 MATERIALS

2.1 General

2.1.1 If there is no suitable piping classification for the required service, the Owner’s Engineershall be notified immediately.

2.1.2 Materials specified under each piping class in Appendix 1 are the minimum acceptable.Substitutions of equivalent materials shall be subject to approval in writing by the Owner’sEngineer.

2.1.3 If there is no suitable component for the Contractor in a pipe class, a custom componentmay be provided with written approval from the Owner’s Engineer. A SP item numbershall be assigned by the Owner’s Engineer to identify these items. The design of all customfittings shall have a CRN as required by CSA B51.

2.1.4 All branch connections shall be PWHT as per the criteria defined by ASME B31.3 Section331.1.3

2.2 Pipe

2.2.1 A minimum wall thickness of Sch 80 shall be used for carbon steel pipe 1 ½” NPS andsmaller, and Sch 80S for stainless steel pipe 1 ½” NPS and smaller, unless statedotherwise.

2.2.2 A minimum wall thickness of Sch 160 shall be used for small bore pipe (NPS ½” - 1 ½”) invibrating service. Lines in vibrating service will be identified in the line list.

2.2.3 Pipe nipples shall not be less than 100 mm long.

2.2.4 All threaded nipples shall be a minimum of Sch. 160.

2.2.5 Electric resistance welded pipe may be used as an alternative to seamless pipe withwritten approval from the Owner’s Engineer.

2.2.6 Odd sizes of pipe such as NPS 1 ¼”, 2 ½”, 3 ½”, 5” and 22” shall not be used.

2.2.7 All carbon steel pipe dimensions must conform to ASME B36.10M and all stainless steelpipe dimensions must conform to ASME B36.19M.

2.2.8 Pipe tolerances shall be those specified in the identified ASTM specification

2.2.9 Welding or couplings shall not be used to achieve double random lengths.

2.2.10 Threaded and coupled piping shall be supplied with taper threaded couplings inaccordance with ASME B1.20.1.

2.2.11 For pipe with a longitudinal weld seam fabricated using a filler material, the maximumhardness of the weld and the heat affected zone (HAZ) shall not exceed 225 BHN.

2.2.12 All pipe shall be supplied free of defects, dirt and debris.

ORBU-SPC-44-0-22



2.3 Valves

2.3.1 Valves are indicated by tag number in each line classification in Appendix 1. Only thevalves listed or approved equivalents shall be used unless a valve is assigned a SP itemnumber on the P&ID’s.

2.3.2 Valves are described in detail by tag number in specification ORBU-SPC-44-0-4, ValveSelection Criteria.

2.4 Fittings

2.4.1 Welding fittings shall have bore to match pipe ID. Misalignment exceeding 1.6 mm will becorrected in accordance with ASME B31.3. Taper bored fittings by anyone but the fittingSeller is prohibited unless prior written approval is obtained from the Owner’s Engineer.

2.4.2 Fittings taper bored by the Seller shall be re-stamped with the thinner wall thickness.

2.4.3 Reducing butt weld fittings shall have same schedule as adjacent pipe on both ends.

2.4.4 Elbows shall be long radius unless the Owner’s Engineer approves short radius bendswhere limited space is available.

2.4.5 The out of roundness of fittings and elbows shall not exceed 4% of the nominal diameter ofthe fitting. Sharp edges on the back of elbows are not acceptable.

2.4.6 Socket-welded and threaded fitting selection is based on ASME B16.11-1996 Table 2. Thistable is as follows:

Pipe Used for Rating BasisClass DesignationOf Fitting

Type of Fitting

Schedule No. Wall Designation2000 Threaded 80 XS3000 Threaded 160 ***6000 Threaded *** XXS

3000 Socket-Welded 80 XS6000 Socket-Welded 160 ***9000 Socket-Welded *** XXS

2.5 Flanges

2.5.1 Bore of flanges shall match pipe ID, otherwise the requirements of paragraph 2.4.1 aboveshall apply.

2.5.2 Flanges with a rating in the range class 150 to 900 inclusive, shall have a raised face andflanges with a rating of class 1500 or greater shall have a ring joint. Substitution of ASMEapproved clamp type connections or other flange types in the classes specified shall besubject to approval in writing by the Owner’s Engineer.

2.5.3 All flanges to be used with SPWD gaskets shall have a surface finish between 125 and 250in AARH.

ORBU-SPC-44-0-22



2.5.4 Orifice flanges shall be per ASME B16.36,and the minimum flange rating shall be ASMEClass 300.

2.5.5 Slip-on flanges shall not be used without written approval from the Owner’s Engineer.

2.5.6 The use of flanges in steam service, where practical, should be minimized. Butt andsocket welded joints are the preferred connection methods. This statement applies topiping classes AVA, BVA, CVA, DVA and EVA.

2.6 Spectacle Blinds

2.6.1 Spectacle blinds shall conform to ASME B16.48.

2.7 Gaskets

2.7.1 Material specified for ring joint gaskets shall be softer than that of the flange facing, with aminimum hardness differential of 50 BHN.

2.7.2 Spiral wound gaskets shall have non-asbestos filler material.

2.8 Bolting

2.8.1 Each stud bolt and nut shall be legibly stamped with its ASTM material grade inaccordance with ASTM A193/194.

2.8.2 The effective length (measured thread to thread) of bolts shall be a minimum of thatrecommended in ASME B16.5.

2.8.3 Bolt lengths not covered by the tables in ASME B16.5 shall be calculated using the givenformulas. Calculated bolt lengths shall be rounded up in increments of ¼” to the nextcommercially available length.

2.9 Branch Connections

2.9.1 Branch connections shall be in accordance with Appendix 3. When specifying weldolets,the schedule of both branch pipe and run pipe must be given.

2.10 Vent, drain and instrument connections shall be in accordance with specification ORBU-SPC-44-0-14.

3.0 SERVICE CLASS INDEX

3.1 Service classifications are identified by a 3 letter designation:

A A A

Pipe materialService

Flange Rating

ORBU-SPC-44-0-22



3.2 The letters are designed as follows:

Flange Rating Service Pipe MaterialA – 150 A – Non-corrosives A – carbon steel A106BB – 300 B – Corrosives B – carbon steel A333 Gr. 6C – 600 C – Chemicals C – stainless steel 316/316LD – 900 D – Acids, Hydrochloric & Sulfuric D – stainless steel 304/304LE – 1500 E – Brine E -F – 2500 F – Cryogenics F – fiberglass reinforced pipe

H – Instrument Air G – carbon steel galvanizedL – Low Temperature Non-Corrosives H – internally coatedQ – Caustics J – copperS – Sour Hydrocarbons K – PE tubingU – Utilities L – polypropylene lined pipeV – Steam, Condensate & Boiler Feed Water M – PTFE lined pipeW – Produced Water N – HDPE pipeX – Low Temperature Sour P – plastic PVCZ – Low Temperature Corrosives Z – carbon steel Z245.1

4.0 PIPING CLASSIFICATION LIST

Class FlangeRating

Service/Commodities

CA(mm)

T(oC)/P(kPa(g))Limits

Pipe Material

AAA 150 Non – CorrosivesSweet Hydrocarbons, Fuel Gas,Produced Oil, Recycle Oil, Sales Oil,Fresh Water, Glycol, Diluent, Processvents & drains, Instrument air, Utility air,Utility water, Fire water, Propane

1.6 -45 / 590-29 / 1965204 / 1378

A106B

AAB 150 Non-CorrosivesInstrument air, Utility air (Low-Temp)

1.6 -45 / 196550 / 1927

A333 Gr.6

AAG 150 Non-CorrosivesUtility water, Domestic water

0 0 / 1965149 / 1585

A106BGalvanized

AAN 150 Non-CorrosivesUtility water, Domestic water(underground)

0 0 / 103423 / 1034

HDPE

ABA 150 CorrosivesProduced Emulsion, Produced Oil,Produced Gas (partial pressure CO2 > 3psia), Demulsifier chemical, ProducedWater

3.2 -45 / 590-29 / 1965204 / 1378

A106B

ACA 150 ChemicalsMagnesium hydroxide, Hydrated Lime,Soda ash

1.6 0 / 1965149 / 1585

A106B

ACC 150 ChemicalsBrine (50oC max), Demulsifier, ReverseDemulsifier, Polymer, Sodium Sulfite,Chelant (EDTA), Steamate NF2000(amine)

0.8 -45 / 1896110 / 1578

316/316L SS

ORBU-SPC-44-0-22



Class FlangeRating

Service/Commodities

CA(mm)


Pipe Material

ACP 150 ChemicalsBrine, Hypochlorite solution

0 0 / 70050 / 700

PVC

ADL 150 AcidsHydrochloric acid (max 35%concentration, <93 oC)

0 -29 / 196593 / 1792

Polypropylenelined

ADM 150 AcidsSulfuric acid (max 95% concentration)

0 -18 / 1965232 / 1275

PTFE lined

AEF 150 BrineBrine (>50 oC)

0 0 / 138099 / 1380

FRP epoxy

ALB 150 Low Temperature, Non-CorrosivesSweet Hydrocarbons, Refrigerant

1.6 -45 / 1965200 / 1395

A333-6

ASA 150 Sour HydrocarbonsSour Produced Oil, Sour Produced Gas

3.2 -45 / 590-29 / 1965204 / 1378

A106BNACE

AVA 150 SteamUtility steam, Boiler Feed Water

1.6 -45 / 590-29 / 1965204 / 1378

A106B

AWA 150 Produced water 3.2 -45 / 590-29 / 1965204 / 1378

A106B

BAA 300 Non-CorrosivesSweet Hydrocarbons, Fuel Gas,Produced Oil, Recycle Slop, Sales Oil,Glycol, Process vents & drains,Instrumentation, Instrument Air

1.6 -45 / 1530-29 / 5102250 / 4180Note 1.

A106B

BBA 300 CorrosivesProduced Emulsion, Produced Oil,Produced Water

3.2 -45 / 1530-29 / 5102250 / 4180Note 1.

A106B

BBZ 300 CorrosivesProduced Emulsion, Fuel Gas

0.9 -45 / 4960230 / 4266Note 2.

Z245.1

BLB 300 Low Temperature, Non-CorrosivesSweet Hydrocarbons, Refrigerant

1.6 -45 / 5102200 / 4389Note 1.

A333-6

BSA 300 Sour HydrocarbonsSour Produced Oil, Sour Produced Gas

3.2 -45 / 1530-29 / 5102250 / 4180Note 1.

A106BNACE

BVA 300 SteamSteam, Boiler Feed Water, Blowdown

1.6 -45 / 1530-29 / 5102250 / 4180Note 1.

A106B

CAA 600 Non-CorrosivesSweet Hydrocarbons, Produced Oil,Recycle slop, Sales Oil, Fuel Gas, Glycol,Process vents & drains

1.6 -45 / 3061-29 / 10204290 / 7883Note 1.

A106B

ORBU-SPC-44-0-22



Class FlangeRating

Service/Commodities

CA(mm)


Pipe Material

CAZ 600 Non-CorrosivesSweet Fuel Gas, Diluent

0.43 -45 / 9930230 / 8092Note 2.

Z245.1

CBA 600 CorrosivesProduced Emulsions, Produced Oil

3.2 -45 / 3061-29 / 10204290 / 7883Note 1.

A106B

CLB 600 Low Temperature, Non-CorrosiveSweet Hydrocarbons, Refrigerant

1.6 -45 / 10204200 / 8781Note 1.

A333-6

CSA 600 Sour HydrocarbonsSour Produced Oil, Sour Produced Gas

3.2 -45 / 3061-29 / 10204250 / 8360Note 1.

A106BNACE

CVA 600 SteamSteam, Boiler Feed Water, Blowdown

1.6 -45 / 3061-29 / 10204290 / 7883Note 1.

A106B

DAA 900 Non-CorrosivesSweet Hydrocarbons, Produced Oil,Recycled Slop, Sales Oil, Fuel Gas,Glycol, Process vents & drains

1.6 -45 / 4590-29 / 15306290 / 11799Note 1.

A106B

DLB 900 Low Temperature, Non-CorrosiveSweet Hydrocarbon, Refrigerant

1.6 -45 / 15306200 / 13139Note 1

A333-6

DSA 900 Sour HydrocarbonsSour Produced Oil, Sour Produced Gas

3.2 -45 / 4590-29 / 15306250 / 12506

A106BNACE

DVA 900 SteamSteam, Boiler Feed Water, Blowdown

1.6 -45 / 4590-29 / 15306344 / 11099Note 1.

A106B

EVA 1500 SteamSteam, Boiler Feed Water, Blowdown

1.6 -45 / 7663-29 / 25545344 / 18509

A106B

Notes:

1. Wall thickness calculations based on actual design conditions required for large bore piping as identified inline class.

2. Wall thickness calculations based on actual design conditions required for all line sizes based on CSAZ662.

5.0 SOUR SERVICE REQUIREMENTS

5.1 General

5.1.1 This section applies to piping materials used in sour service as defined by NACE StandardMR-0175, latest edition. The following are requirements that must be complied with inaddition to those listed in MR-0175.

ORBU-SPC-44-0-22



5.2 Material

5.2.1 Cast iron and austenitic ductile iron shall not be used.

5.2.2 Components fabricated from carbon steel shall be killed low carbon steel. When thecomponents are intended for welding they shall also have the following properties:

5.2.2.1 When trace elements are shown on the carbon steel MTR the CE shall be lessthan or equal to 0.45%. The CE is defined as follows:

CE = % C + % Mn/6 + (% Cr + % Mo + % V) /5 + (% Ni + % Cu)/15

5.2.2.2 When trace elements are not shown on the carbon steel MTR the CE is defined asfollows and shall be less than 0.04%:

CE = % C + % Mn/6

5.2.3 All carbon steel butt welds greater than 9.5 mm, that are exposed to sour service, shall bePWHT. For butt welds of pipe with wall thickness less than 9.5 mm, PWHT is not requiredif the weldment is hardness tested to be 22 HRC or less as required by NACE MR-0175latest edition. Testing shall include the filler, the HAZ (both sides) and the base material(both sides).

All carbon steel fillet welds, that are exposed to sour service, shall be PHWT if theweldment is hardness tested to be greater than 22 HRC or if the weld meets the criteria forPWHT as defined by ASME B31.3 Section 331.1.3.

PWHT of carbon steel materials shall be at a minimum temperature of 620oC for a holdtime of one hour per inch of nominal wall thickness, or a minimum total hold time of onehour. After post weld heat treatment, the Heat Affected Zone (HAZ) shall not exceed 22HRC for low carbon steel materials.

5.2.4 All welds shall preheat to a minimum of 38oC.

5.2.5 Threaded connections shall only be used where allowed by the appropriate pipe class andthen only where socket weld connections are impractical.

5.2.6 Slip – on flanges shall not be used.

5.2.7 Inspection, Testing and Repairs

5.2.7.1 No welding or welded attachments shall be allowed after PWHT.

5.2.7.2 All welds that can be radiographed shall be 100% radiographed after PWHT.Welds that can not be radiographed shall be examined by ultrasonic, magneticparticle or liquid penetrant methods as specified in the purchase order.

5.2.7.3 Impact testing shall be in accordance with ASME B31.3. The acceptance standardfor ultrasonic or magnetic particle testing shall be in accordance with ASME B31.3.

5.2.7.4 Carbon steel material hardness shall not exceed 22 HRC.

ORBU-SPC-44-0-22



5.2.7.5 Hardness testing for B31.3 code system shall be in accordance with ASTM E384.Hardness testing for CSA Z662 code system shall be in accordance with ASTME18.

5.2.7.6 Cold stamping of weld components shall be done with low stress stamps on thefitting alongside the weld.

6.0 MATERIAL IDENTIFICATION

6.1 All material shall bear the identification markings as required by the applicable standards andspecifications (e.g., ASTM, ASME, API, MSS, etc.

6.2 Mill test reports shall be furnished for all materials.

6.3 Materials shall be marked with a longitudinal paint stripe 5 mm wide running the full length of thepipe or component. On austenitic stainless steel the marking paint shall contain no harmful metal ormetal salts such as zinc, lead, copper, chlorine, or sulfur which cause corrosive attack uponheating. For Positive Material Identification requirements refer to specification ORBU-SPC-43-10-5.

7.0 HANDLING AND SHIPMENT

7.1 General

7.1.1 Items shall be thoroughly cleaned and dried inside and outside to remove all dirt, debrisand foreign matter.

7.1.2 The Seller shall supply the Engineering Contractor with copies of all shipping lists thatidentify all items. The Engineering Contractor shall be notified at least twenty-four (24)hours in advance of shipping dates.

7.2 Pipe

7.2.1 Pipe openings shall be covered as follows:

7.2.1.1 All machined surfaces shall be coated with an anti-rust compound that is approvedby the Engineering Contractor.

7.2.1.2 Threaded ends shall be plugged with tight fitting plastic plugs or threaded steelplugs.

7.2.1.3 Beveled ends shall be protected with tight fitting plastic or steel caps.

7.2.2 Carbon steel pipe shall not be tied down with carbon steel chains, cables, or otherwise besecured against carbon steel truck decks without load softening or blocking.

7.2.3 Stainless steel pipe shall not be tied down with carbon steel chains, cables, or otherwisebe secured against carbon steel truck decks without load softening or blocking.

7.2.4 Coated or jacketed pipe shall be handled with wide rubber or canvas belts without forwardor backward scuffing motion. Hooks, chains, cables or rope of any kind shall not be used.

7.2.5 Coated and jacketed pipe shall be shipped in cradled bundles.

ORBU-SPC-44-0-22



7.3 Flanges and Fittings

7.3.1 All flange faces, machined surfaces and threaded connections shall be coated with rustpreventative.

7.3.2 Flanged openings shall be closed with steel or heavy wooden covers securely fastened tothe flange to prevent damage to the face or foreign matter entering the pipe.

7.3.3 Threaded openings shall be protected with steel or plastic plugs.

7.3.4 All loose fittings, bolting and other small parts shall be suitably packaged for shipment andidentified to indicate which spool they are intended for.

7.3.5 A suitable thread lubricant shall be used on all bolted connections.

7.4 Valves

7.4.1 Valves shall be identified with the tag number stamped or embossed in 12.7 mm (1/2”)characters on metal tags or strips securely wired or banded to the valve in an easily visiblelocation. Tags, strips, wires and bands shall be stainless steel.

ORBU-SPC-44-0-22Appendix 1

Page 1 of 83

APPENDIX 1 - PIPING CLASSIFICATIONS


Page 2 of 83

PIPING CLASS: AAA

DESIGN BASISService: Non-corrosives

Sweet hydrocarbons, fuel gas, produced oil, recycle slop, sales oil, fresh water,glycol, diluent, process vents & drains, instrument air, utility air, utility water, firewater, propane.

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 1.6 mmTemperature Range: -45 to 204C Note 5Pressure Limits: 590 kPa(g) @ -45 to -30C Note 5

1965 kPa(g) @-29 to 38C1792 kPa(g) @ 93C1585 kPa(g) @ 149C1378 kPa(g) @ 204oC

NDE: Category II (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS

DESCRIPTION CODE/STD NOTES

Pipe ASTM A106B, SMLS ASMEB36.10M

½ – 1½ XS/Sch 80, PE2 – 24 Std, BE

Fittings ½ – 1½ 3000#, ASTM A105, SW ASMEB16.11

2 – 24 ASTM A234-WPB, BW ASMEB16.9

Flanges ½ - 1½ Class 150, RF, ASTM A105, SW ASMEB16.5

2 – 24 Class 150, RF, ASTM A105, WNBlinds ½ - 24 Class 150, RF, ASTM A105

Orifice Flanges ½ - 1 ½ Class 300, RF, WN, ASTM A105, ½”FNPT tap

ASMEB16.36

2-24 Class 300, RF, WN, ASTM A105, ½”FNPT tapc/w bolts, nuts and jack screws

Unions ½ - 1½ 3000#, ASTM A105, SW or Scrd., steelto steel seat

ASMEB16.11

Plugs ½ - 1½ Solid hex head, ASTM A105 ASMEB16.11


Page 3 of 83

PIPING CLASS: AAA

Nipples Pipe ½ - 1½

½

Sch 160, PExTE & TExTE, ASTMA106B, 100 mm longSch 160, TE x TE, ASTM A106B,175 mm long

ASMEB36.10M

1

8

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE, thickness atboth ends to match that of mating pipe.

Spectacle Blinds, Spades& Spacers

½ - 24 Class 150, RF, ASTM A516-70N ASMEB16.48

2

Gaskets SPWD, Class 150, RF, 304SSwinding, mica-graphite filler, CScentering ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

Bolting Stud bolt , full thread, ASTM A193-B7hex nuts, ASTM A194-2H (refer toASME B16.5 for bolt lengths)

ASMEB16.5

Tubing ¼ 0.028” W.T., ASTM A269-316 SS,SMLS

4

⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

4

½ 0.049” W.T., ASTM A269-316 SS,SMLS

4

¾ 0.083” W.T., ASTM A269-316 SS,SMLS

4

Tube Fittings 316 SS, short compression type –Swagelok

Olets ASTM A105 - for types and sizes referto Table 1 Branch Connections inAppendix 3

ASMEB16.11


Page 4 of 83

PIPING CLASS: AAA

VALVES DESCRIPTION TAG NOTESGate ½ – 1½ Class 800, SW, A105

Class 800, SWxTE, A105GS-08A00GX-08A00

2 – 24 Class 150, RF, A216-WCB GF-01A00 6Globe ½ – 1½ Class 800, SW, T-Pattern, A105

Class 800, SW, Y-Pattern, A105TS-08A00TS-08A10

2 – 24 Class 150, RF, T-Pattern A216-WCBClass 150, RF, Y-Pattern A216-WCB

TF-01A00TF-01A10

6

Check ½ – 1½ Class 800, SW, Piston, A105Class 800, SW, Swing, A105

CS-08A20CS-08A00

2 – 24 Class 150, RF, Swing, A216-WCBClass 150, RF, Lug, A216-WCBClass 150, RF, Wafer, A216-WCB

CF-01A00CL-01A60CW-01A60

Ball ½ – 1½ 2000# CWP, SW, RP, Soft Seat,A1052000# CWP, SW, FP, Soft Seat,A105

BS-20A00

BS-20A20

2 – 24 Class 150, RF, RP, Soft Seat, A216-WCBClass 150, RF, FP, Soft Seat, A216-WCB

BF-01A00

BF-01A20

7

Butterfly 2 – 24 Class 150, Lug, Resilient Seat,A216-WCB

FL-01A00 3, 9

Instrument ½ – 1½ 3000# CWP, Threaded NeedleValve, A105

NT-30A00Alt. NS-30A00, NX-30A00

NOTES

1. In glycol service use threaded connections only after root valve on instrument sensing lines.2. Spectacle blinds may be used up to size 12 NPS. Spades and/or spacers only shall be used in line sizes NPS

14 - 24.3. Use of resilient seated butterfly valves limited to a maximum temperature of 150ºC (302ºF).4. See separate detail on glycol tracing tubing standards.5. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.6. NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.7. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.8. For use on orifice flange connections only.9. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.


Page 5 of 83

PIPING CLASS: AAB


Instrument and Utility Air (Low-Temp)Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 1.6 mmTemperature Range: -45 to 50oCPressure Limits: 1965 kPa(g) @ -45 to 38oC

1927 kPa(g) @ 50oCNDE: Category II (see Appendix 2)PWHT: Not requiredImpact Testing: Welds per Box A-4, Table 323.3.1 of ASME B31.3

ITEM SIZENPS


Pipe ASTM A333-6, SMLS ASMEB36.10M

½ – 1½ XS/Sch 80, PE or Scrd.2 – 4 Std, BE

Fittings ½ – 1½ 3000#, ASTM A350-LF2 Class 1, SWor Scrd.

ASMEB16.11

2 – 4 ASTM A420-WPL6, BW ASMEB16.9

Flanges ½ - 1½ Class 150, RF, ASTM A350-LF2,Class 1, SW or Scrd.

ASMEB16.5

2 – 4 Class 150, RF, ASTM A350-LF2,Class 1, WN

Blinds ½ - 4 Class 150, RF, ASTM A350-LF2,Class 1

Orifice Flanges ½ - 1 ½ Class 300, RF, WN, ASTM A350-LF2,Class 1, ½” FNPT tap

ASMEB16.36

2 - 4 Class 300, RF, WN, ASTM A350-LF2,Class 1, ½” FNPT tap c/w bolts, nutsand jack screws

Unions ½ - 1½ 3000#, ASTM A350-LF2, Class 1,Scrd. or SW, steel to steel seat

ASMEB16.11

Plugs ½ - 1½ Solid hex head, ASTM A350-LF2,Class 1

ASMEB16.11

Nipples Pipe ½ - 1½ Sch 160, PExTE & TExTE ASTMA333-6, 100 mm longSch 160, TExTE ASTM A333-6,175 mm long

ASMEB36.10M

1


Page 6 of 83

PIPING CLASS: AAB

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, A420-WPL6 orA350-LF2, Class 1A234-WPB, PE, thickness at both endsto match that of mating pipe.

Spectacle Blinds ½ - 4 Class 150, RF, ASTM A516-70N ASMEB16.48

2

Gaskets ½ - 4 SPWD, Class 150, RF, 304SS windingmica-graphite filler CS centering ring,3.2 mm thick (e.g., Flexitallic orequivalent)

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A320-L7hex nuts, ASTM A194-7 (refer toASME B16.5 for bolt lengths).

ASMEB16.5


⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

½ 0.049” W.T., ASTM A269-316 SS,SMLS

¾ 0.083” W.T., ASTM A269-316 SS,SMLS


Olets ASTM A350-LF2, Class 1 - for typesand sizes refer to Table 1 BranchConnections in Appendix 3

ASMEB16.11


Page 7 of 83

PIPING CLASS: AAB

VALVES DESCRIPTION TAG NOTESGate ½ – 1½ Class 800, TBE, A350-LF2, Class 1

Class 800, SWxTE, A350-LF2,Class 1Class 800, SW, A350-LF2, Class 1

GT-08L00GX-08L00

GS-08L002 – 4 Class 150, RF, A352-LCC, OS&Y GF-01L00

Globe ½ – 1½ Class 800, TBE, T-Pattern, A350-LF2, Class 1

TT-08L00

2 – 4 Class 150, RF, T-Pattern, A352-LCC TF-01L00Check ½ – 1½ Class 800, TBE., Piston, A350-LF2,

Class 1CT-08L20

2 – 4 Class 150, RF, Swing, A352-LCC CF-01L00Ball ½ – 1½ 2000# CWP, TBE, RP, Floating Ball,

Teflon SeatsBT-20L00

2 – 4 Class 150, RF, RP, Floating Ball,Teflon Seats

BF-01L00

Butterfly 2 – 4 Class 150, Lug, Resilient Seat,A352-LCC

FL-01L00

Instrument ¾ by ½ 3000# CWP, Threaded NeedleValve, A350-LF2

NT-30L00Alt. NS-30L00, NX-30L00

NOTES

1. For use on orifice flange connections only.


Page 8 of 83

PIPING CLASS: AAG


Utility water, domestic waterCode: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 0 mmTemperature Range: 0 to 149oCPressure Limits: 1965 kPa(g) @ 0 to 38oC

1792 kPa(g) @ 93oC1585 kPa(g) @ 149oC

NDE: Category IV (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe ASTM A106B, SMLS, Galvanized ASMEB36.10M

½ – 1½ XS/Sch 80, Scrd.2 – 4 Std, Scrd.

Fittings ½ – 4 3000#, ASTM A105, Scrd., Galvanized ASMEB16.11

Flanges ½ - 4 Class 150, RF, ASTM A105, Scrd.,Galvanized

ASMEB16.5

Blinds ½ - 4 Class 150, RF, ASTM A105,Galvanized

Orifice Flanges ½ - 1 ½ Class 300, RF, ASTM A105, Scrd.,Galvanized, ½” FNPT tap

ASMEB16.36

2-4 Class 300, RF ASTM A105, Scrd.,Galvanized, ½” FNPT tap c/w bolts,nuts and jack screws

Unions ½ - 1½ 3000#, ASTM A105, Scrd.,Galvanized, steel to steel seat

ASMEB16.11

Plugs ½ - 1½ Solid hex head, ASTM A105,Galvanized

ASMEB16.11

Nipples Pipe ½ - 4 XS/Sch 80, TExTE, ASTM A106B,Galvanized, 100 mm longXS/Sch 80, TExTE, ASTM A106B,Galvanized, 175 mm long

ASMEB36.10M

1

Swage ½ - 3 XS/Sch 80, TExTE, A234-WPB orA105, Galvanized


Page 9 of 83

PIPING CLASS: AAG


½ - 4 Class 150, RF, ASTM A516-70N,Galvanized

ASMEB16.48

Gaskets SPWD, Class 150, RF, 304SS windingmica-graphite filler, CS centering ring,3.2 mm thick (i.e. Flexitallic orequivalent)

ASMEB16.20


ASMEB16.5


⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

½ 0.049” W.T., ASTM A269-316 SS,SMLS

¾ 0.083” W.T., ASTM A269-316 SS,SMLS


Olets N/A

VALVES DESCRIPTION TAG NOTESGate ½ – 1½ Class 800, TE, A105 GT-08A00

2 – 4 Class 150, RF, A216-WCB GF-01A00Check ½ – 1½ Class 800, TE, Piston, A105 CT-08A20

2 – 4 Class 150, RF, Swing, A216-WCB CF-01A00Ball ½ – 1½ 2000# CWP, TE, RP, Soft Seat Ball

Valve, A105BT-20A00

2 – 4 Class 150, RF, RP, Soft Seat BallValve, A216-WCB

BF-01A00


NT-30A00

NOTES

1. For use on orifice flange connections only.


Page 10 of 83

PIPING CLASS: AAN


Utility water, domestic water (underground)Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 0 mmTemperature Range: 0 to 23oCPressure Limits: 1034 kPa(g) @ 0 to 23oCNDE: Category IV (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe ASTM F714, HDPE to ASTM D3350 ASME2 – 8 P3408 – DR11

Fittings2 – 8

ASTM D3350, HDPEP3408 – DR11, ends flanged withbacking ring drilled to ASME B16.5

ASME

2 – 8 ASTM D3350, HDPEP3408 – DR11, butt fusion ends

Flanges 2 – 8 HDPE Class 150, P3408 – DR11, FFstub end, ductile iron backing ringdrilled to ASME B16.5

ASMEB16.5

Blinds N/A

Orifice Flanges N/A

Unions N/A

Plugs N/A

Nipples Pipe N/ASwage N/A


N/A

Gaskets 2 – 8 Class 150, 3.2 mm thick, full faceneoprene

ASMEB16.20

Bolting ASTM A307, Gr. B machine bolts c/whex head nuts.

ASMEB16.5

Tubing N/A

Tube Fittings N/A

Olets N/A

VALVES DESCRIPTION TAG NOTESGate As determined by project.


Page 11 of 83

PIPING CLASS: ABA

DESIGN BASISService: Corrosives

Produced emulsion, produced oil, produced gas (partial pressure CO2 > 3 psia),produced water, demulsifier chemical

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 3.2 mmTemperature Range: -45 to 204oC Note 6Pressure Limits: 590 kPa(g) @ -45oC to -30C Note 6

1965 kPa(g) @ -29oC to 38C1792 kPa(g) @ 93C1585 kPa(g) @ 149C1378 kPa(g) @ 204oC


ITEM SIZENPS



½ – 1½ XS/Sch 80, PE2 XS/Sch 80, BE2½ – 24 Std, BE



Flanges ½ - 1 ½ Class 150, RF, ASTM A105, SW ASMEB16.5



ASMEB16.36

2 – 24 Class 300, RF, WN, ASTM A105, ½”FNPT tapc/w bolts, nuts and jack screws

Unions Use flanges

Plugs ½ – 1-½ Solid hex head, ASTM A105 ASMEB16.11

Nipples Pipe ½ – 1½

½

Sch 160, PExTE & TExTE, ASTMA106B, 100 mm longSch 160, TExTE, ASTM A106B,175 mm long

ASMEB36.10M

7

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE, thickness atboth ends to match that of matingpipe.


Page 12 of 83

ITEM SIZENPS




1

Gaskets SPWD, Class 150, RF, 304SSwinding mica-graphite filler, CScentering ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7,Hex nuts, ASTM A194-2H, (refer toASME B16.5 for bolt lengths)

ASMEB16.5

Tubing For temperature <71ºC:¼ 0.028” W.T., ASTM A269-316 SS,

SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS3

¾ 0.083” W.T., ASTM A269-316 SS,SMLSFor temperature ≥71ºC:

¼ 0.028” W.T., ASTM A269 CS, SMLS 4, 5⅜ 0.035” W.T., ASTM A269 CS, SMLS 4, 5½ 0.049” W.T., ASTM A269 CS, SMLS 3, 4, 5¾ 0.083” W.T., ASTM A269 CS, SMLS 4, 5

Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC:CS with zinc coating, shortcompression type – Swagelok

4, 5

Olets ASTM A105 - for types and sizesrefer to Table 1 Branch Connectionsin Appendix 3

ASMEB16.11


Page 13 of 83

Valves Description TAG NotesGate ½ – 1½ Class 800, SW, A105




2 – 24 Class 150, RF, T-Pattern, A216-WCBClass 150, RF, Y-Pattern, A216-WCB

TF-01A00

TF-01A10

8

Check ½ – 1½ Class 800, SW, Piston, A105 CS-08A202 – 24 Class 150, RF, Swing, A216-WCB

Class 150, RF, Lug, A216-WCBClass 150, RF, Wafer, A216-WCB

CF-01A00CL-01A60CW-01A60

Ball ½ – 1½ 2000# CWP, SW, RP, Soft Seat,A1052000# CWP, SW, FP, Soft Seat,A105

BS-20A00

BS-20A20

2 – 24 Class 150, RF, RP, Soft Seat, A216-WCB

BF-01A00 9


FL-01A00 2, 8, 10


NT-30A00Alt. NS-30A00, NX-30A00

NOTES

1. Spectacle blinds may be used up to size 12 NPS. Spades and/or spacers only shall be used in line sizes NPS14 - 24.

2. Use of resilient seated butterfly valves limited to a maximum temperature of 150oC (302oF).3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. For use on orifice flange connections only.8. NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.9. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.10. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “GO”.


Page 14 of 83

PIPING CLASS: ACA

DESIGN BASISService: Chemicals

Magnesium hydroxide, hydrated lime, soda ashCode: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 1.6 mmTemperature Range: 0 to 149oCPressure Limits: 1965 kPa(g) @ 0 oC to 149oC

1792 kPa(g) @ 93oC1585 kPa(g) @ 149oC

NDE: Category V (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS



½ – 1½ XS/Sch 80, Scrd.2 – 4 Std, BE

Fittings ½ – 1½ 3000#, ASTM A105, Scrd. ASMEB16.11


Flanges ½ - 1½ Class 150, RF, ASTM A105, TEClass 150, FF, ASTM A105, TE

ASMEB16.5

2 – 4 Class 150, RF, ASTM A105, WNClass 150, FF, ASTM A105, WN

Blind ½ - 4 Class 150, RF, ASTM A105Class 150, FF, ASTM A105

ASMEB16.5

Orifice Flanges ½ - 1 ½ N/A ASMEB16.36

Unions N/A ASMEB16.11

Plugs N/A ASMEB16.11

Nipples Pipe ½ - 1½ XS/Sch 80, TE, ASTM A106B,100 mm long

ASMEB36.10M

Swage ½ - 1½

2 & 3

XS/Sch 80, PE & TE, ASTM A234-WPB or A105ASTM A234-WPB, PE, thickness atboth ends to match that of mating pipe

Spectacle Blinds,Spades & Spacers

½ - 4 Class 150, RF or FF, A516-70N ASME 16.48

Gaskets ½ - 4 Flat ring, Class 150, 3.2 mm thick(i.e.Hypalon or approved equivalent)

ASMEB16.21


Page 15 of 83

ITEM SIZENPS



ASMEB16.5

Tubing N/A

Tube Fittings N/A

Olets 2 - 4 3000#, ASTM A105for types and sizes refer to Table 1Branch Connections in Appendix 3

Thread Compound Teflon tape

VALVES TAG NOTESCheck ½ – 1½ Class 800, SW, Swing, A105

Class 800, TBE, Swing, A105CS-08B02CT-08B02

2 – 4 Class 150, RF, Swing, A216-WCB CF-01B04Ball ½ – 1½ 2000# CWP, TBE, RP, Soft Seat,

A105BT-20B00

Plug 2 – 4 Class 150, FF, RP, Soft Seat, CastIron

PE-01B01

Pinch 1 – 4 Class 150, RF Flanges Valve, CastIron

HF-01B00 1

NOTES

1. Pinch valve operating conditions limited to 1103 kPa (160 psi) @ 150oC(302oF).


Page 16 of 83

PIPING CLASS: ACC


Brine (50ºC max), demulsifier, reverse demulsifier, polymer, sodium sulphite,chelant (EDTA), Steamate NF2000 (amine)

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 0.8 mmTemperature Range: -45 to 110ºCPressure Limits: 1585 kPa(g) @ -45ºC to 38C

1344 kPa(g) @ 93C1303 kPa(g) @ 110ºC

NDE: Category V (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe ½ – 1½ ASTM A312 TP316/316L, SMLS ,Sch 80,PE

ASMEB36.19M

2 – 4 ASTM A312 TP316/316L, SMLS, Sch 10S,BE

Fittings ½ – 1½ 3000#, ASTM A182, F316/316L, SW ASMEB16.11

2 – 4 ASTM A403 WP 316/316L-S, BW ASME B16.9

Flanges ½ - 1½ Class 150, RF, ASTM A182 F316/316L,SW

ASME B16.5

2 – 4 Class 150, RF, ASTM A182 F316/316L,lap joint, type A

Blind ½ - 4 Class 150, RF, ASTM A182 F316/316L ASME B16.5

Stub End Lap joint, MSS SP43, type A short,316/316L, Sch 10S

Orifice Flanges N/A

Unions N/A

Plugs N/A

Nipples Pipe N/ASwage


½ - 4 Class 150, RF, A240 316/316L ASMEB16.48

Gaskets Flat ring for RF flanges, Virgin or inorganicfilled PTFE 3.2 mm thick (i.e. Garlock,Chesterton, or approved equiv.)

ASMEB16.21

Bolting Stud bolt , full thread, ASTM A193-B7M,Hex nuts, ASTM A194-2HM refer toASME B16.5 for bolt lengths)

ASME B16.5

Tubing ⅛ 0.028” W.T., ASTM A269-316 SS, SMLS⅜ 0.035” W.T., ASTM A269-316 SS, SMLS½ 0.049” W.T., ASTM A269-316 SS, SMLS


Page 17 of 83

ITEM SIZENPS


¾ 0.083” W.T., ASTM A269-316 SS, SMLSTube Fittings 316 SS, short compression type –

Swagelok

Olets ½ - 4 ASTM A182, F316/316L - for types andsizes refer to Table 1 Branch Connectionsin Appendix 3

ASMEB16.11

1

Thread Compound N/A

VALVES DESCRIPTION TAG NOTES

Gate ½ – 1½

2 – 4

Class 800, SW, A182-F316/316LClass 800, SWxTE ,A182-F316/316LClass 150, RF, A351-CF8M

GS-08B01GX-08B01

GF-01B01Globe ½ – 1½ Class 800, SW, T-Pattern,

A182-316/316LTS-08B01

2 – 4 Class 150, RF, T-Pattern,A351-CF8M

TF-01B01

Check ½ – 1½ Class 800, SW, Piston,A182-316/316L

CS-08B01

2 – 4 Class 150, RF, Swing,A351-CF8M

CF-01B01

Ball ½ – 1½ 2000# CWP, SW, RP, Soft SeatA182-F316/316L

BS-20B00

2 – 4 Class 150, RF, RP, Soft Seat,A351-CF8M

BF-01B00

Butterfly 2 – 4 Class 150, Lug, Resilient Seat,A351-CF8M

FL-01B00

Instrument ¼ – 1½ 10,000# CWP, Threaded Valve,A182-316

NT-99B00

NOTES

1 Use thredolets for instrument connections only.


Page 18 of 83

PIPING CLASS: ACP


Brine (<50oC), Hypochlorite SolutionCode: CSA B137.3Flange Rating: Class 150Corrosion Allowance: 0.0 mmTemperature Range: 0 to 50ºCPressure Limits: 700 kPa(g) @ 0ºC to 50CNDE: 100 % VisualPWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe ½ – 4 Sch 80, PVC, Type 1, Gr. 1 (CellClassification) 012454-B conforming toASTM D1784

CSA B137.3 4

Fittings ½ – ¾

½ – 4

Sch 80, Scrd.to ASTM D2464, PVC, Type 1,Gr. 1 (Cell Classification) 012454-Bconforming to ASTM D1784Sch 80, SW to ASTM D2467, PVC, Type 1,Gr. 1 (Cell Classification) 012454-Dconforming to ASTM D1784

CSA B137.3 1 thru 4

Flanges ½ – 4 Class 150, FF, SW, ASTM A105, Sch 80,PVC, Type 1, Gr. 1 (Cell Classification)012454-B conforming to ASTM D1784

CSA B137.3 4

Blind N/A

Orifice Flanges N/A

Unions N/A

Plugs N/A

Nipples Pipe ½ – 1½ Sch 80, PVC, Type 1, Gr. 1 (CellClassification) 012454-B conforming toASTM D1784

CSA B137.3

Swage N/A

Spectacle Blinds Spades& Spacers

Gaskets ½ – 4 Class 150, full faced, ethylene propylenerubber (EPDM), 3.2 mm thick

Bolting Machine bolts, ASTM A307-B with hex nutsand washers

Tubing N/A

Tube Fittings N/A

Olets N/ASolvent Compound ASTM D2564


Page 19 of 83

VALVES TAG NOTES

Check ½ – 4 Ball type, PVC body, solvent weldends, true-union ends, PTFE seats,viton O-ring.

CS-01B05

2-4 Class 150, RF Flanges, Swing,A351-CF8M

CF-01B01

Ball ½ – 4 PVC body, solvent weld ends, true-union safe-block design, PTFEseats, viton O-ring.

BS-01B01

Butterfly 2 – 4 Class 150, Lug, Resilient Seat,A351-CF8M

FL-01B00

Globe ½ – 2 Y-pattern or angle pattern, PVC bodyand bonnet, solvent weld ends,PTFE seats, viton O-ring.

TS-01B12

Globe 2 – 4 Class 150, RF, T-Pattern,A351-CF8M

TF-01B01

NOTES

1. Elbows shall be long radius type unless shown otherwise.2. Joints shall be socket weld type except where connecting to unions, valves and equipment, use threaded

connections. No threaded connections larger than ¾” are permitted.3. Fittings shall have the same continuous working pressure rating as the pipe.4. Install per manufacturer’s recommendations.


Page 20 of 83

PIPING CLASS: ADL

DESIGN BASISService: Acids

Hydrochloric acid (max. 35% concentration, <95ºC), brine; Caustic (0 to 50%concentration)

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: NoneTemperature Range: -29 to 93ºCPressure Limits: 1965 kPa(g) @ -29ºC to 38C

1792 kPa(g) @ 93CNDE: Category VI (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe 1 – 6 ASTM A587, ERW, Sch 40, polypropylenelined to ASTM F1545, Swaged

ASMEB31.3

1

(Reference: Crane Resistoflex)8 ASTM A587, ERW, Sch 30, polypropylene

lined to ASTM F1545, Swaged(Reference: Crane Resistoflex)

Fittings 1 – 8 Class 150, RF flanged, ASTM A216 WCB,polypropylene lined to ASTM F1545

ASMEB16.9

(Reference: Crane Resistoflex)

Flanges 1 – 8 Class 150, ASTM A105, polypropylene linedto ASTM F1545, Chamfered Threaded orRotatable

ASMEB16.5

2

Stub end 1 – 6 ASTM A105, Sch 40, NPT8 ASTM A105, Sch 30, NPT

Blind 1 – 8 Class 150, RF, WN, ASTM A105,polypropylene lined to ASTM F1545

ASMEB16.5

Orifice Flanges N/A

Unions N/A

Plugs N/A



1 – 8 Class 150, ASTM A516-70N, PTFE lined, RF ASMEB16.48

Gaskets 1 – 8 Class 150, reinforced PTFE ring, 3.0 mmthick

3

Bolting Stud bolt, full thread, ASTM A193-B7, hexnuts, ASTM A194-2H (refer to ASME B16.5for bolt lengths).

ASMEB16.5

Tubing ¼ 0.028” W.T., ASTM B622 Hastelloy C-276,Smls


Page 21 of 83

ITEM SIZENPS


⅜ 0.035” W.T., ASTM B622 Hastelloy C-276,Smls

½ 0.049” W.T., ASTM B622 Hastelloy C-276,Smls

Tube Fittings Hastelloy C-276, short compression type –Swagelok

Olets N/AThread Compound None

VALVES TAG NOTES

Check 1 – 8 Class 150, RF, Ball Check Valve,A395 - Ductile Iron, PFA lined

CF-01B50

Ball 1 – 8 Class 150, RF, FP, Soft Seat BallValve, A395 - PFA Lined

BF-01B21

Plug 1 – 8 Class 150, RF, RP, Soft Seat PlugValve, A395 – Ductile Iron, PFA lined

PF-01B00

NOTES

1 For piping downstream of acid dilution, due to high temperatures use PTFE-lined carbon steel piping (referenceline classification ADM)

2 Install spray shields on all flanges in acid service.3 Gaskets required only for connection to equipment and unlined components.


Page 22 of 83

PIPING CLASS: ADM

DESIGN BASISService: Acids

Sulfuric acid (95% maximum concentration)Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: NoneTemperature Range: -18 to 232ºCPressure Limits: 1965 kPa(g) @ -18ºC to 38C

1792 kPa(g) @ 93C1585 kPa(g) @ 149C1378 kPa(g) @ 204C1275 kPa(g) @ 232ºC

NDE: Category VI (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe 1 - 6 ASTM A587, ERW, Sch 40, PTFE lined toASTM F1545, Thermalok

ASME B31.3


Fittings 1 - 6 Class 150, RF flanged, ASTM A216 WCB,PTFE lined to ASTM F1545

ASME B16.9


Flanges 1 - 6 Class 150, Thermalok (Van Stone), ASTMA105, PTFE lined to ASTM F1545

ASME B16.5 1

Blind 1 - 6 Class 150, RF, ASTM A105, PTFE lined toASTM F1545

ASME B16.5

Orifice Flanges N/A

Unions N/A

Plugs N/A



1 - 6 Class 150, ASTM A516-70N, PTFE lined,RF

ASME B31.3

Gaskets 1 - 6 Class 150, reinforced PTFE ring, 3.0 mmthick

2

Bolting Stud bolt, full thread, ASTM A193-B7, hexnuts, ASTM A194-2H (refer to ASME B16.5for bolt lengths).

ASME B16.5

Tubing ¼ 0.028” W.T., ASTM B622 Hasteloy C-276,SMLS

⅜ 0.035” W.T., ASTM B622 Hasteloy C-276,SMLS

½ 0.049” W.T., ASTM B622 Hasteloy C-276,SMLS


Page 23 of 83

ITEM SIZENPS


¾ 0.065” W.T., ASTM B622 Hasteloy C-276,SMLS

Tube Fittings Hasteloy C-276, short compression type –Swagelok

Olets N/AThread Compound None

VALVES TAG NOTES

Check 1 – 4 Class 150, RF, Ball Check Valve,A395 – Ductile Iron, PFA Lined

CF-01B50

Ball 1 – 4 Class 150, RF, FP, Soft Seat BallValve, A395 - PFA Lined

BF-01B21

Plug 1 – 4 Class 150, RF, RP, Soft Seat PlugValve, A395–Ductile Iron, PFA Lined

PF-01B00

NOTES

1 Install spray shields on all flanges in acid service.2 Gaskets required only for connection to equipment and unlined components.


Page 24 of 83

PIPING CLASS: AEF

DESIGN BASISService: Tank Vents

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 0Temperature Range: 0 to 99ºCPressure Limits: 1380 kPa(g) @ 99ºNDE: Category VI (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZENPS


Pipe 1 - 12 Filament wound, RTRP epoxy ASME B31.3(Reference: Bondstrand Series 2000M orapproved equal)

Fittings 1 - 12 Filament wound, RTRP epoxy, femaleends

1

(Reference: Bondstrand Series 2000M orapproved equal)

Flanges 1 - 12 Class 150, FF, RTRP epoxy, female end ASME B16.5 2(Reference: Bondstrand Series 2000M orapproved equal)

Blind 1 - 12 Class 150, FF, RTRP epoxy ASME B16.5(Reference: Bondstrand Series 2000M orapproved equal)

Orifice Flanges N/A

Unions N/A

Plugs N/A



Class 150, ASTM 516-70, PTFE lined, FF ASME B31.3

Gaskets Class 150, full face, EPDM, 3.0 mm thick,Shore A durometer hardness 60 ± 5

Bolting Stud bolt, full thread, ASTM A307-B, hexnuts, ASTM A307-B Carbon steel washers

ASME B16.5 3

Tubing N/A

Tube Fittings N/A

Olets N/A


Page 25 of 83

Cement epoxy adhesive for FRP epoxy(e.g., Bondstrand RP-34C epoxy adhesiveor approved substitute)


Check 3 – 6 Class 150, Wafer, Swing, A395 -Ductile Iron

CW-01B02

1 – 4 Class 150, RF, Ball Check, A395 -Ductile Iron

CF-01B50

Ball ½ – 1½ Class 150, RF, FP, Soft Seat, A395- PFA Lined

BF-01B21

Butterfly 2 – 6 Class 150, Lug, Resilient Seat ,A216-WCB

FL-01B01

NOTES

1 Elbows shall be filament wound, long radius type unless shown otherwise.2 Follow piping manufacturers recommended installation procedures for connection to raised face flanges.3 Follow manufacturers recommended torque settings for tightening flange bolts.


Page 26 of 83

PIPING CLASS: ALB

DESIGN BASISService: Low Temperature, Non-Corrosives

Sweet hydrocarbons, refrigerantCode: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 1.6 mmTemperature Range: -45 to 200ºCPressure Limits: 1965 kPa(g) @ -45ºC

1395 kPa(g) @ 200ºCNDE: Category II (see Appendix 2)PWHT: Not requiredImpact Testing: Welds per Box A-4, Table 323.3.1 of ASME B31.3

ITEM SIZENPS


Pipe ASTM A333 Gr. 6, SMLS ASMEB36.10M

½ – 1½ XS/Sch 80, PE 12 – 24 Std, BE

Fittings ½ – 1½ 3000#, ASTM A350-LF2, Class 1, SW ASMEB16.11

2 – 24 A420 Gr. WPL6, BW ASMEB16.9

Flanges ½ - 1½ Class 150, RF, ASTM A350-LF2, Class 1,SW

ASMEB16.5

2 – 24 Class 150, RF, ASTM A350-LF2, Class 1,WN

Blinds ½ - 24 Class 150, RF, ASTM A350-LF2, Class 1


ASMEB16.36

2 - 24 Class 300, RF, WN, ASTM A350-LF2,Class 1, ½” FNPT tapc/w bolts, nuts and jack screws

Unions ½ - 1½ 3000#, ASTM A350-LF2, Class 1, SW,steel to steel seat

ASMEB16.11

Plugs ½ - 1½ Solid hex head, ASTM A350-LF2, Class 1 ASMEB16.11


½

Sch 160, PExTE & TExTE, ASTM A333Gr. 6, 100 mm longSch 160, TExTE, ASTM A333 Gr. 6, 175mm long

ASMEB31.3

2

5

Swage ½ - 1½ Sch 160, PE & TE, ASTM A420 WPL6 orASTM A350-LF2, Class 1

2 & 3 ASTM A420-WPL6, PE, thickness at bothends to match that of mating pipe



3

Gaskets SPWD, Class 150, RF ASMEB16.20


Page 27 of 83

ITEM SIZENPS


316 SS windingmica-graphite fillerCS centering ring, 3.2 mm thick

Bolting stud bolt , full thread, ASTM A320-L7 ASMEB16.5

hex nuts, ASTM A194-7(refer to ASME B16.5 for bolt lengths)

Tubing ¼ & ⅜ 0.035”, ASTM A-269 316 SS, SMLS½ 0.049”, ASTM A-269 316 SS, SMLS

Tube Fittings ¼ - ½ 316 SS

Olets ASTM A350-LF2, Class 1, for types andsizes refer to Table 1 Branch Connectionsin Appendix 3

ASMEB16.11


Gate ½ – 1½ Class 800, SW, A350-LF2, Class 1Class 800, SWxTE, A350-LF2,Class 1

GS-08L00GX-08L00

2 – 24 Class 150, RF, A352-LCC GF-01L00 6Globe ½ – 1½ Class 800, SW, T-Pattern,

A350-LF2, Class 1Class 800, SW, Y-Pattern,A350-LF2, Class

TS-08L00

TS-08L10

2 – 24 Class 150, RF, T-Pattern, A352-LCCClass 150, RF, Y-Pattern, A352-LCC

TF-01L00TF-01L10

6

Check ½ – 1½ Class 800, SW, Piston, A350-LF2,Class 1

CS-08L20

2 – 24 Class 150, RF, Swing, A352-LCC CF-01L00Ball ½ – 1½ 2000# CWP, SW, RP, Soft Seat,

A350-LF2, Class 1BS-20L00 4

2 – 24 Class 150, RF Flanges, RP, SoftSeat Ball Valve, A352-LCC

BF-01L00 7

Instrument ½ – 1½ 3000# CWP, Threaded NeedleValve, 316 SS

NT-30S00Alt. NS-30S00, NX-30S00

NOTES

1 Use Sch 160 for pipe NPS 1½ in vibrating service.2 In glycol service use threaded connections only after root valve on instrument sensing lines.3 Spectacle blinds may be used up to size 12 NPS. Spades and/or spacers only shall be used in line sizes 14 -

24 NPS.4 Use of ball valves limited to a maximum temperature of 80ºC.5 For use on orifice flange connections only.6 NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.7 NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 28 of 83

PIPING CLASS: ASA

DESIGN BASISService: Sour Hydrocarbons

Sour produced oil, sour produced gas (As defined by NACE MR-0175, LatestEdition)

Code: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 3.2 mmTemperature Range: -45 to 204ºC Note 6Pressure Limits: 590 kPa(g) @ -45ºC to -30ºC Note 6

1965 kPa(g) @ -29ºC to 38ºC1792 kPa(g) @ 93ºC1585 kPa(g) @ 149ºC1378 kPa(g) @ 204ºC

NDE: Category III (see Appendix 2)PWHT: All Welds (See Note 3)Impact Testing: Not required

ITEM SIZENPS


Pipe ASTM A106B SMLS ASMEB36.10M

½ – 1½ Sch 160, PE 42 XS/Sch 80, BE 42½ – 24 Std, BE 4


4


4


4

2 – 24 Class 150, RF, ASTM A105, WN 4Blinds ½ - 24 Class 150, RF, ASTM A105 4


ASMEB16.36

4

2 – 24 Class 300, RF, WN, ASTM A105, ½”FNPT tap

4

c/w bolts, nuts and jack screws

Unions ½ - 1½ 3000#, ASTM A105, SW or Scrd, steelto steel seat

ASMEB16.11

4

Plugs ½ - 1 ½ Solid hex head, ASTM A105 ASMEB16.11

Nipples Pipe ½– 1½ Sch 160, PExTE and TExTE, ASTMA106B, 100 mm longSch 160, TExTE, ASTM A106B,175 mm long

ASMEB31.3

4

7

Swage ½ - 1 ½

2 & 3

Sch 160, PE & TE,ASTM A234-WPBor A105ASTM A234-WPB, PE, – thickness atboth ends to match that of mating pipe.

4


Page 29 of 83

ITEM SIZENPS




1, 4

Gaskets SPWD, Class 150, RF, 316L SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick e.g.,Flexitallic or equivalent).

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7M, hex nuts, ASTM A194-2HM(refer to ASME B16.5 for bolt lengths).

ASMEB16.5


⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

½ 0.049” W.T., ASTM A269-316 SS,SMLS

¾ 0.083” W.T., ASTM A269-316 SS,SMLS

ITEM SIZENPS




ASMEB16.11


Page 30 of 83


Gate ½ – 1½ Class 800, SW, A105Class 800, SWxTE, A105

GS-08S00GX-08S00

4

2 – 24 Class 150, RF, A216-WCB GF-01S00 4, 8Globe ½ – 1½ Class 800, SW, T-Pattern, A105

Class 800, SW, Y-Pattern, A105TS-08S00TS-08S10

4

2 – 24 Class 150, RF, T-Pattern,A216-WCBClass 150, RF, Y-Pattern,A216-WCB

TF-01S00

TF-01S10

4, 8

Check ½ – 1½ Class 800, SW, Piston, A105 CS-08S20 42 – 24 Class 150, RF, Swing, A216-WCB


CF-01S00CL-01S60CW-01S60

4

Ball ½ – 1½ 2000# CWP, SW, RP, Soft Seat,A105

BS-20S00 4

2 – 24 Class 150, RF, RP, Soft Seat,A216-WCB

BF-01S00 4, 9


FL-01S00 2, 4, 10

Instrument ½ – 1½ 3000# CWP, SW x Threaded NeedleValve, 316 SS

NX-30S00Alt. NS-30S00, NT-30S00

4

NOTES


2. Use of resilient seated butterfly valves limited to a maximum temperature of 150ºC (302ºF).3. For pipe sizes NPS 10 and smaller PWHT is not required if the weldment is hardness tested to be less than 22

HRC as required by NACE MR-0175, Latest Edition and Section 5.2. Testing shall include the filler, the HAZ(both sides) and the base material (both sides).

4. All material used must meet the requirements of NACE MR-0175, Latest Edition.5. The Contractor’s WPS & PQR shall include preheat greater than 38C.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. For use on orifice flange connections only.8. NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.9. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 31 of 83

PIPING CLASS: AVA

DESIGN BASISService: Steam

Utility steam, boiler feed waterCode: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 1.6 mmTemperature Range: -45 to 204ºC Note 5Pressure Limits: 590 kPa(g) @ -45ºC to –30ºC Note 5

1965 kPa(g) @ -29ºC to 38ºC1792 kPa(g) @ 93ºC1585 kPa(g) @ 149ºC1378 kPa(g) @ 204ºC


ITEM SIZENPS



½ – 1½ XS/Sch 80, PE2 – 24 Std, BE




9

2 – 24 Class 150, RF, ASTM A105, WN 9Blinds ½ - 24 Class 150, RF, ASTM A105


ASMEB16.36

2 - 24 Class 300, RF, WN, ASTM A105, ½”FNPT tapc/w bolts, nuts and jack screws


ASMEB16.11



½

Sch 160, PExTE & TExTE, ASTMA106B, 100 mm longSch 160, TExTE, ASTM A106B, 175mm long

ASMEB36.10M

6

Nipples Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE, – thickness atboth ends to match that of mating pipe



1


Page 32 of 83

ITEM SIZENPS


Gaskets SPWD, Class 150, RF, 304SSwinding, mica-graphite filler, CScentering ring, 3.2 mm thick, (e.g.,Flexitallic or equivalent)

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7,hex nuts, ASTM A194-2H, (refer toASME B16.5 for bolt lengths)

ASMEB16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS2



Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC:CS with zinc coating, shortcompression type – Swagelok

3, 4


ASMEB16.11


Page 33 of 83



GS-08A00GX-08A00




TF-01A00

TF-01A10

7

Check ½ – 1½ Class 800, SW, Piston, A105 CS-08A202 – 24 Class 150, RF, Swing, A216-WCB CF-01A00

Ball ½ – 1½

2-24

2000# CWP, SW, RP, Soft Seat,A105Class 150, RF, RP, Soft Seat,A216-WCB

BS-20A00

BF-01A00

8


NT-30V00Alt. NS-30V00, NX-30V00

NOTES

1. Spectacle blinds may be used up to size 12 NPS. Spades and/or spacers only shall be used in line sizes 14 -24 NPS.

2. Preferred size.3. HRB less than or equal to 72.4. By exception, where installation detail specifies metallurgy.5. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.6. For use on orifice flange connections only.7. NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”8. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”9. Refer to paragraph 2.5.6 of this specification for preferred connection methods for steam service.


Page 34 of 83

PIPING CLASS: AWA

DESIGN BASISService: Produced waterCode: ASME B31.3Flange Rating: ASME Class 150Corrosion Allowance: 3.2 mmTemperature Range: -45 to 204oC Note 6Pressure Limits: 590 kPa(g) @ -45oC to -30C Note 6

1965 kPa(g) @ -29oC to 38C1792 kPa(g) @ 93C1585 kPa(g) @ 149C1378 kPa(g) @ 204oC


ITEM SIZENPS



½ – 1½ XS/Sch 80, PE2 XS/Sch 80, BE3 – 24 Std, BE






ASMEB16.36

2 – 24 Class 300, RF, WN, ASTM A105, ½”FNPT tapc/w bolts, nuts and jack screws

Unions Use flanges

Plugs ½ – 1-½ Solid hex head, ASTM A105 ASMEB16.11

Nipples Pipe ½ – 1½

½


ASMEB36.10M

7

Swage ½ – 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of matingpipe.



1


Page 35 of 83

ITEM SIZENPS


Gaskets SPWD, Class 150, RF, mica-graphitefiller, CS centering ring, 3.2 mm thick(e.g., Flexitallic or equivalent).

ASMEB16.20

For temperature <71ºC:304SS windingFor temperature ≥71ºC:CS or Monel winding

Bolting Stud bolt, full thread, ASTM A193-B7,Hex nuts, ASTM A194-2H, (refer toASME B16.5 for bolt lengths)

ASMEB16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS3



Tube Fittings For temperature <71ºC316 SS, short compression type –SwagelokFor temperature ≥71ºCCS with zinc coating, shortcompression type – Swagelok

4, 5

Olets ASTM A105 – for types and sizesrefer to Table 1 Branch ConnectionsinAppendix 3

ASMEB16.11


Page 36 of 83

Valves Description TAG Notes


GS-08A00GX-08A00



2 – 24 Class 150, RF, T-Pattern, A216-WCBClass 150, RF, YT-Pattern, A216-WCB

TF-01A00

TF-01A10

8


Class 150, Lug, A216-WCBCF-01A00CL-01A60


BS-20A00 9


BF-01A00


FL-01A00 10


NT-30A00Alt. NS-30A00, NX-30A00

NOTES

1. Spectacle blinds may be used up to size 12 NPS. Spades and/or spacers only shall be used in line sizes NPS 14 – 24.

2. Use of resilient seated butterfly valves limited to a maximum temperature of 150ºC (302ºF).3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. For use on orifice flange connections only.8. NPS 12” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.9. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 37 of 83

PIPING CLASS: BAA


Sweet hydrocarbons, fuel gas, produced oil, recycle slop, sales oil, glycol,process vents & drains, instrument air

Code: ASME B31.3Flange Rating: ASME Class 300Corrosion Allowance: 1.6 mmTemperature Range: -45 to 250ºC Note 4Pressure Limits: 1530 kPa(g) @ -45ºC to -30C Note 4

5102 kPa(g) @ -29ºC to 38C4653 kPa(g) @ 93C4516 kPa(g) @ 149C4378 kPa(g) @ 204C4180 kPa(g) @ 250ºC

Examination: Category II (see Appendix 2)PWHT: Not requiredImpact Testing: Not required

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESPipe ASTM A106B, SMLS ASME

B36.10M½ - 1½ XS/Sch 80, PE2 - 14 Std, BE16 - 20 XS, BE24 Calculate thickness, BE 5

Fittings ½– 1½ 3000#, ASTM A105, SW ASMEB16.11


Flanges ½ - 1½ Class 300, RF, ASTM A105, SW, ASMEB16.5



ASMEB16.36



ASMEB16.11



½


ASMEB36.10M

6


Page 38 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESSwage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE, - thickness atboth ends to match that of mating pipe.



7

Gaskets SPWD, Class 300, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent)

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7,hex nuts, ASTM A194-2H (refer toASME B16.5 for bolt lengths).

ASMEB16.5


2

⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

2

½ 0.049” W.T., ASTM A269-316 SS,SMLS

3, 2

¾ 0.083” W.T., ASTM A269-316 SS,SMLS

2

Tube Fittings 316 SS, short compression type -Swagelok


ASMEB16.11


Page 39 of 83

NOTES

1. Ball valves have limited maximum temperatures.Teflon seats: 100ºC (212ºF)PEEK seats: 230ºC (450ºF)

2. See separate detail on glycol tracing tubing standards.3. Preferred size.4. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.5. Calculate required pipe thickness based on line design temperature and design pressure.6. For use on orifice flange connections only.7. Spectacle blinds may be used up to size 10 NPS. Spades and/or spacers only shall be used in line sizes 12 –

24 NPS.8. NPS 10” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.9. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.



GS-08A00Alt. GX-08A00




TF-03A00

TF-03A10

8



CF-03A00CL-03A60CW-03A60


BS-20A00 1


BF-03A00 1, 9

Butterfly 2 – 24 Class 300, Lug, A216-WCB FL-03A10 10Instrument ½ – 1½ 3000# CWP, Threaded Needle

Valve, A105NT-30A00Alt. NS-30A00, NX-30A00


Page 40 of 83

PIPING CLASS: BBA


Produced emulsion, produced oil, produced waterCode: ASME B31.3Flange Rating: ASME Class 300Corrosion Allowance: 3.2 mmTemperature Range: -45 to 250oC Note 6Pressure Limits: 1530 kPa(g) @ -45C to -30C Note 6

5102 kPa(g) @ -29oC to 38C4653 kPa(g) @ 93C4516 kPa(g) @ 149C4378 kPa(g) @ 204C4180 kPa(g) @ 250oC



B36.10M½ - 1½ XS/Sch 80, PE2 - 12 XS, BE14 – 24 Calculate thickness, BE 7

Fittings ½ - 1½ 3000#, ASTM A105, SW ASMEB16.11





ASMEB16.36


Unions Use flanges



½

Sch 160, PExTE &TExTE, ASTMA106B, 100 mm longSch 160, TExTE, ASTM A106B,175 mm long

ASMEB36.10M

8Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE, – thickness atboth ends to match that of mating pipe.



1


Page 41 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESGaskets SPWD, Class 300, RF, 304SS

winding, mica-graphite filler, CScentering ring, 3.2 mm thick (i.e.Flexitallic or equivalent)

ASMEB16.20

Bolting Stud bolt , full thread, ASTM A193-B7,hex nuts, ASTM A194-2H (refer toASME B16.5 for bolt lengths).

ASMEB16.5

Tubing For temperature <71ºC:¼ 0.028” W.T., ASTM A269-316 SS, SMLS⅜ 0.035” W.T., ASTM A269-316 SS, SMLS½ 0.049” W.T., ASTM A269-316 SS, SMLS 3¾ 0.083” W.T., ASTM A269-316 SS, SMLS

For temperature ≥71ºC & <204ºC :¼ 0.028” W.T., ASTM A269 CS, SMLS 4, 5⅜ 0.035” W.T., ASTM A269 CS, SMLS 4, 5½ 0.049” W.T., ASTM A269 CS, SMLS 3, 4, 5¾ 0.083” W.T., ASTM A269 CS, SMLS 4, 5

Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC & <204ºC :CS with zinc coating, shortcompression type – Swagelok

4, 5


ASMEB16.11


Page 42 of 83



GS-08A00GX-08A00


Class 800, SW. Y-Pattern, A105TS-08A00TS-08A10


TF-03A00

TF-03A10

9



CF-03A00CL-03A60CW-03A60


BS-20A00 2


BF-03A00 2, 10

Butterfly 2 – 24 Class 300, Lug, A216-WCB FL-03A10 11Instrument ½ – 1½ 3000# CWP, SW x Threaded Needle

Valve, A105NX-30A00Alt. NS-30A00, NT-30A00

NOTES


2. Ball valves seats have limited maximum temperature.Teflon seats: 100ºC (212ºF)PEEK seats: 230ºC (450ºF)

3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required pipe thickness based on line design pressure and design temperature.8. For use on orifice flange connections only.9. NPS 10” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-G0”.11. NPS 8” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 43 of 83

PIPING CLASS: BBZ


Produced emulsion, fuel gasCode: CSA Z662Flange Rating: PN 50Corrosion Allowance: 0.78 mmTemperature Range: -45 to 230oCPressure Limits: 5102 kPa(g) @ -45C to 38C

4653 kPa(g) @ 93C4516 kPa(g) @ 149C4378 kPa(g) @ 204C4266 kPa(g) @ 230oC

NDE: As per CSA Z662-03, Section 7.10.2.1PWHT: Not required (Note 2)Impact Testing: Not required

ITEM SIZENPS


Pipe CSA Z245.1, CAT. I CSA Z6622 - 12 Calculate thickness, Grade 359,

SMLS, ERW or SAW, BE2 - 12 XS, Grade 241, SMLS, BE 1

Fittings CSA Z245.11, CAT. I CSA Z6622 - 12 Grade to match pipe, ends to match

pipe, BW

Flanges CSA Z245.12, CAT. I CSA Z6622 – 12 PN 50, RFWN, Grade 248, Bore to

match pipe1

Blinds 2 – 12 PN 50, RFWN, Grade 248 1

Orifice Flanges N/A

Unions Use flanges

Plugs N/A


Spectacle Blinds,Spades, & Spacers

N/A

Gaskets SPWD, Class 300, RF, 304SSwinding mica-graphite filler, CScentering ring, 3.2 mm thick (e.g.,Flexitallic or equivalent)

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A320-L7,hex nuts, ASTM A194-7 (refer toASME B16.5 for bolt lengths)

ASMEB16.5

Tubing N/ATube Fittings N/A


Page 44 of 83

ITEM SIZENPS


Olets N/A

Valves Description TAG Notes

N/ANOTES

1. For use as riser material only2. PWHT is required for joints of unequal wall thickness as per CSA Z662-03, Section 7.9.16.1 Note 2)3. For NPS ½ to 1½ piping and valves refer to piping class BBA.4. For NPS 2 and larger valves refer to piping class BBA with the additional requirement that the valves meet CSA

Z245.15.5. Calculate required pipe thickness based on line design pressure and temperature.


Page 45 of 83

PIPING CLASS: BLB



4389 kPa(g) @ 200ºCExamination: Category II (see Appendix 2)PWHT: Not requiredImpact Testing: Welds as per Box A-4, Table 323.3.1 of ASME B31.3ITEM SIZE

NPSDESCRIPTION CODE/STD NOTES

Pipe ASTM A333 Gr. 6, SMLS ASMEB31.3

½ – 1½ XS/Sch 80, PE 12 – 14 Std, BE16 - 20 XS, BE24 Calculate thickness, BE 2

Fittings ½ – 1½ 3000#, FS, ASTM A350-LF2, Class 1, SW ASMEB16.11

2 – 24 A420 Gr. WPL6, BW ASMEB16.9


ASMEB16.5




ASMEB16.36

2 - 24 Class 300, RF, WN, ASTM A350-LF2,Class 1, ½” FNPT tapc/w bolts, nuts and jack screws

Unions ½ - 1½ 3000#, ASTM A350-LF2, Class 1, SW,steel to steel seat

ASMEB16.11


Nipples Pipe ½ - 1½ Sch 160, PExTE & TExTE, ASTM A333Gr. 6, 100 mm long

ASMEB31.3

½ Sch 160, TExTE, ASTM A333 Gr. 6,175 mm long

Swage ½ - 1½ Sch 160, PE & TE, ASTM A420 Gr. WPL6or ASTM A350-LF2, Class 1

2 & 3 ASTM A420 Gr. WPL6, PE, thickness atboth ends to match that of mating pipe


½ - 24 Class 300, RF, ASTM A516-70N ASME 16.48 3


Page 46 of 83

Gaskets SPWD, Class 300, RF, 304 SS winding,mica-graphite filler, CS centering ring,3.2 mm thick

ASMEB16.20

(i.e. Flexitallic or equivalent)





Olets ASTM A350-LF2, Class 1 ASMEB16.11

for types and sizes refer to Table 1Branch Connections in Appendix 3


Gate ½ – 1½ Class 800, SW, A350-LF2, Class 1Class 800, SWxTE, A350-LF2,Class 1

GS-08L00GX-08L00


A350-LF2, Class 1Class 800, SW, Y-Pattern,A350-LF2, Class 1

TS-08L00

TS-08L10


TF-03L00TF-03L10

5


CS-08L20


A350-LF2, Class 1BS-20L00

2 – 24 Class 300, RF, RP, Soft Seat, A352-LCC

BF-03L00 4, 6


NT-30S00Alt. NS-30S00, NX-30S00

NOTES

1 Use Sch 160 for pipe NPS 1½ in vibrating service.2 Calculate required pipe thickness based on line design pressure and design temperature.3 Spectacle blinds may be used up to size 10 NPS. Spades and/or spacers only shall be used in line sizes 12 -

24 NPS.4 Use of ball valves limited to a maximum temperature of 100ºC.5 NPS 10” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.6 NPS 6” and above shall be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 47 of 83

PIPING CLASS: BSA



Code: ASME B31.3Flange Rating: ASME Class 300Corrosion Allowance: 3.2 mmTemperature Range: -45 to 250oC Note 6Pressure Limits: 1530 kPa(g) @ -45C to -30C Note 6

5102 kPa(g) @ -29C to 38C4653 kPa(g) @ 93C4516 kPa(g) @ 149C4378 kPa(g) @ 204C4180 kPa(g) @ 250ºC

NDE: Category III (see Appendix 2)PWHT: All welds (See Note 2)Impact Testing: Not required


B36.10M½ - 1 ½ XS/Sch 80, PE 32 - 12 XS, BE 314 - 24 Calculate thickness, BE 3, 7

Fittings ½ - 1½ 3000#, FS, ASTM A105, SW ASMEB16.11

3

2 – 24 ASTM A234 WPB, BW ASMEB16.9

3

Flanges ½ - 1½ Class 300, RF, ASTM A105, SW ASMEB16.5 3



ASMEB16.36

3

2 - 24 Class 300, RF, WN, ASTM A105, ½”FNPT tap

3



ASMEB16.11

3


3


½

Sch 160, PExTE & TEx TE, ASTMA106B, 100 mm longSch 160, TExTE, ASTM A106B,175 mm long

ASMEB31.3

3

8

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of mating pipe.

3


Page 48 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESSpectacle Blinds,Spades, & Spacers


4

Gaskets SPWD, Class 300, RF, 316L SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent)

ASMEB16.20


ASMEB16.5

Tubing ¼ 0.028” W.T., ASTM A269-CS, SMLS⅜ 0.035” W.T., ASTM A269-CS, SMLS½ 0.049” W.T., ASTM A269-CS, SMLS¾ 0.083” W.T., ASTM A269-CS, SMLS

Tube Fittings CS, short compression type –Swagelok


ASMEB16.11

3


Page 49 of 83



GS-08S00GX-08S00

2 – 24 Class 300, RF, A216-WCB GF-03S00 9Globe ½ – 1½ Class 800, SW, T-Pattern, A105



TF-03S00

TF-03S10

9

Check ½ – 1½ Class 800, SW, Piston, A105 CS-08S202 – 24 Class 300, RF, Swing, A216-WCB

Class 300, RF, Lug, A216-WCBCF-03S00CL-03S60


BS-20S00 1


BF-03S00 1, 10

Butterfly 2 – 24 Class 300, Lug, A216-WCB FL-03S10 11Instrument ½ – 1½ 3000# CWP, Threaded Needle

Valve, 316 SSNT-30S00Alt. NS-30S00, NX-30S00

NOTES

1. Ball valves have limited maximum temperatureTeflon seats: 100ºC (212ºF)PEEK seats: 230ºC (450ºF)

2. For pipe sizes NPS 4 and smaller PWHT is not required if the weldment is hardness tested to be less than 22HRC as required by NACE MR-0175, Latest Edition and Section 5.2. Testing shall include the filler, the HAZ(both sides) and the base material (both sides).

3. All material used must meet the requirements of NACE MR-0175, Latest Edition.4. Spectacle blinds may be used up to size NPS 10. Spades and /or spacers shall only be used in line sizes NPS

12 - 245. The Contractor’s WPS & PQR shall include preheat greater than 38C.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required pipe thickness based on line design pressure and design temperature.8. For use on orifice flange connections only.9. NPS 10” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.11. NPS 8” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 50 of 83

PIPING CLASS: BVA


Steam, boiler feed water, blowdownCode: ASME B31.3Flange Rating: ASME Class 300Corrosion Allowance: 1.6 mmTemperature Range: -45 to 250oC Note 5Pressure Limits: 1530 kPa(g) @ -45C to -30C Note 5

5102 kPa(g) @ 38C4653 kPa(g) @ 93C4516 kPa(g) @ 149C4378 kPa(g) @ 204C4180 kPa(g) @ 250ºC

NDE: Category II (see Appendix 2)PWHT: Not requiredImpact Testing:: Not required

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESPipe ASTM A106B, SMLS ASME B31.3

½ - 1½ XS/Sch 80, PE2 - 14 Std, BE16 - 20 XS, BE24 Calculate thickness 6

Fittings ½ - 1 ½ 3000#, ASTM A105, SW or Scrd. ASMEB16.11

2 - 24 ASTM A234-WPB, BW ASME B16.9

Flanges ½ - 1 ½ Class 300, RF, ASTM A105, SW ASME B16.5 102 - 24 Class 300, RF, ASTM A105, WN 10

Blinds ½ - 24 Class 300, RF, ASTM A105


ASMEB16.36



ASMEB16.11



½

Sch 160, PExTE & TExTE, ASTMA106B, 100 mm longSch 160,TExTE, ASTM A106B,175 mm long

ASME B31.3

7

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPB orASTM A105ASTM A234-WPB, PE - thickness atboth ends to match that of mating pipe.



1


Page 51 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESGaskets SPWD, Class 300, RF, 304SS winding,

mica-graphite filler, CS centring ring,3.2 mm thick (i.e. Flexitallic orequivalent).

ASMEB16.20


ASME B16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS2

¾ 0.083” W.T., ASTM A269-316 SS,SMLSFor temperature ≥71ºC<204ºC :


Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC<204ºC :CS with zinc coating, short compressiontype – Swagelok

3, 4


ASMEB16.11


Page 52 of 83


Gate ½ – 1½ Class 800, SW, A105 GS-08A00Alt. GX-08A00, GT-08A00




TF-03A00

TF-03A10

8



BS-20A00


BF-03A00 9


NT-60V00Alt. NS-60V00, NX-60V00

NOTES

1. Spectacle blinds may be used up to size 10 NPS. Spades and/or spacers only shall be used in line sizes NPS12 – 24.

2. Preferred size.3. HRB less than or equal to 72.4. By exception, where installation detail specifies metallurgy.5. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.6. Calculate pipe thickness based on line design pressure and design temperature.7. For use on orifice flange connections only.8. NPS 10” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.9. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.10. Refer to paragraph 2.5.6 of this specification for preferred connection methods for steam service.


Page 53 of 83

PIPING CLASS: CAA


Sweet hydrocarbons, produced oil, recycle slop, sales oil, fuel gas, glycol,process vents and drains

Code: ASME B31.3Flange Rating: ASME Class 600Corrosion Allowance: 1.6 mmTemperature Range: -45 to 290ºC Note 3Pressure Limits: 3061 kPa(g) @ -45C to -30C Note 3

10204 kPa(g) @ -29C to 38C9307 kPa(g) @ 93C9066 kPa(g) @ 149C8756 kPa(g) @ 204C8273 kPa(g) @ 260C7883 kPa(g) @ 290ºC

NDE: Category II (see Appendix 2)PWHT: > 19 mm Wall ThicknessImpact Testing: Not required


B36.10M½ - 1½ Sch 160, PE2 – 8 Sch 80, BE10 - 24 Calculate thickness, BE 4

Fittings ½ – 1½ 3000#, FS, ASTM A105 ASMEB16.11

½ – 1½ 6000#, FS, ASTM A105, SW2 – 24 ASTM A234-WPB, BW ASME

B16.9



Orifice Flanges ½ - 24 Class 600, RF, WN, ASTM A105, ½”SW tap

ASMEB16.36


Unions Use flanges



½

Sch 160, PExTE & TExTE, ASTMA106B, 100 mm longSch 160, PExTE, ASTM A106B,175 mm long

ASMEB36.10M

5

Swage ½ - 1½

2 & 3

Sch 160, PE & TE, ASTM A234-WPBor ASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of mating pipe.


Page 54 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESSpectacle Blinds, Spades& Spacers


1

Gaskets SPWD, Class 600, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7,hex nuts, ASTM A194-2H, (refer toASME B16.5 for bolt lengths).

ASMEB16.5


⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

½ 0.049” W.T., ASTM A269-316 SS,SMLS

¾ 0.083” W.T., ASTM A269-316 SS,SMLS

Tube Fittings 316 SS, short compression type -Swagelok


ASMEB16.11


Page 55 of 83



GS-08A00GX-08A00




TF-06A00

TF-06A10

6


Class 600, RF, Lug, A216-WCBCF-06A00CL-06A60


BS-20A00 2


BF-06A00 2, 6


NT-30A00Alt. NS-30A00, NX-30A00, NC-30A00

NOTES


2. Ball valves have limited maximum temperature.Teflon seats: 80ºC (176ºF)PEEK seats: 230ºC (450ºF)

3. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.4. Calculate pipe thickness based on line design pressure and design temperature.5. For use on orifice flange connections only.6. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 56 of 83

PIPING CLASS: CAZ


Sweet fuel gas, diluentCode: CSA Z662Flange Rating: PN 100Corrosion Allowance: 0.74 mmTemperature Range: -45 to 230oCPressure Limits: 9930 kPa(g) @ -45C to 38C

9307 kPa(g) @ 93C9066 kPa(g) @ 149C8756 kPa(g) @ 204C8092 kPa(g) @ 230C

NDE: As per CSA Z662-03, Section 7.10.2.1PWHT: Not required (Note 2)Impact Testing: Not required

ITEM SIZENPS


Pipe CSA Z245.1, CAT. I CSA Z6622 - 12 Calculate thickness, Grade 359,

SMLS, ERW or SAW, BE2 - 12 Sch 80, Grade 241, SMLS, BE 1

Fittings CSA Z245.11, CAT. I CSA Z6622 – 12 Grade to match pipe, Ends to match

pipe, BW1

Flanges CSA Z245.12, CAT. I CSA Z662PN 100, RFWN, Grade 248, Bore tomatch pipe

1

Blinds PN 100, RF, Grade 248 1

Orifice Flanges N/A

Unions Use flanges

Plugs N/A



N/A

Gaskets SPWD, Class 600, RF, 304SSwinding mica-graphite filler, CScentering ring, 3.2 mm thick (e.g.,Flexitallic or equivalent)

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7 ASMEB16.5

hex nuts, ASTM A194-2H(refer to ASME B16.5 for bolt lengths)

Tubing N/A


Page 57 of 83

ITEM SIZENPS


Tube Fittings N/A

Olets N/AValves Description TAG Note

sN/A

NOTES

1. For use as riser material only.2. PWHT is required for joints of unequal wall thickness as per CSA Z662-03, Section 7.9.16.1 Note 2.3. For NPS ½ to 1½ piping and valves refer to piping class CAA.4. For NPS 2 and larger valves refer to piping class CAA with the additional requirement that the valves meet CSA

Z245.15.


Page 58 of 83

PIPING CLASS: CBA


Produced emulsion, produced oil, produced waterCode: ASME B31.3Flange Rating: ASME Class 600Corrosion Allowance: 3.2 mmTemperature Range: -45 to 290ºC Note 6Pressure Limits: 3061 kPa(g) @ -45C to -30C Note 6

10204 kPa(g) @ -29C to 38C9307 kPa(g) @ 93C9066 kPa(g) @ 149C8756 kPa(g) @ 204C8273 kPa(g) @ 260C7883 kPa(g) @ 290ºC



B36.10M½ - 1½ Sch 160, PE2 Sch 160, BE3 – 8 Sch 80, BE10 - 24 Calculate thickness, BE 9




2 – 24 Class 600, RF, ASTM A105, WNAlt. – Clamp joint c/w 17-4 PH SS sealring with graphite coating, ASTM A105hubs, A266 CL-3 clamp set, ASTMA193-B7 studs, & ASTM A194-2Hbolts (Grayloc)

Blinds ½ - 24 Class 600, RF, ASTM A105

Orifice Flanges ½ - 24 Class 600, RF, WN, ASTM A105, ½”SW Tap

ASMEB16.36


Unions Use flanges



½

XXS, PExTE & TExTE, ASTM A106B,100 mm longXXS, PExTE, ASTM A106B, 175 mmlong

ASMEB36.10M

7


Page 59 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESSwage ½ - 1½

2 & 3

XXS, PE & TE, ASTM A234-WPB orASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of mating pipe.



1

Gaskets SPWD, Class 600, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick(e.g.,Flexitallic or equivalent)

ASMEB16.20


ASMEB16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS3

¾ 0.083” W.T., ASTM A269-316 SS,SMLS

For temperature ≥71ºC & <204ºC :¼ 0.028” W.T., ASTM A269 CS, SMLS 4, 5⅜ 0.035” W.T., ASTM A269 CS, SMLS 4, 5½ 0.049” W.T., ASTM A269 CS, SMLS 3, 4, 5¾ 0.083” W.T., ASTM A269 CS, SMLS 4, 5

Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC & <204ºC :CS with zinc coating, shortcompression type – Swagelok

4, 5


ASMEB16.11


Page 60 of 83





2 – 24 Class 600, RF, T-Pattern,A216-WCBClass 600, RF, T-Pattern,A216-WCB

TF-06A00

TF-06A10

8


Class 600, RF, Lug, A216-WCBCF-06A00CL-06A60


BS-20A00 2


BF-06A00 2, 8


NX-30A00Alt. NS-30A00, NT-30A00

NOTES



3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. For use on orifice flange connections only.8. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.9. Calculate required wall thickness based on line design pressure and design temperature.


Page 61 of 83

PIPING CLASS: CLB



8781 kPa(g) @ 200ºCNDE: Category II (see Appendix 2)PWHT: > 19 mm Wall ThicknessImpact Testing: Welds per Box A-4, Table 323.3.1 of ASME B31.3

ITEM SIZENPS



½ – 1½ XS/Sch 80, PE 12 - 8 Sch 80, BE10 - 24 Calculate thickness, BE 2


2 – 24 ASTM A420 Gr. WPL6, BW ASMEB16.9


ASMEB16.5



Orifice Flanges ½ - 24 Class 600, RF, WN, ASTM A350-LF2,Class 1, ½” SW tap

ASMEB16.36


Unions Use flanges


Nipples Pipe ½ - 1½ Sch 160, PExTE & TExTE, ASTM A333Gr. 6, 100 mm longSch 160, PExTE, ASTM A333 Gr. 6,175 mm long

ASMEB36.10M

3

Swage ½ - 1½ Sch 160, PE & TE, ASTM A420 Gr. WPL6or ASTM A350-LF2, Class1

2 & 3 ASTM A420 Gr. WPL6, PE, - thickness atboth ends to match that of mating pipe



4

Gaskets SPWD, Class 600, RF ASMEB16.20

316 SS winding


Page 62 of 83

ITEM SIZENPS


mica-graphite fillerCS centering ring, 3.2 mm thick(e.g., Flexitallic or equivalent)






for types and sizes refer to Table 1 BranchConnections in Appendix 3

VALVES DESCRIPTION TAG NOTESGate ½ – 1½ Class 800, SW, A350-LF2, Class 1

Class 800, SWxTE, A350-LF2,Class 1

GS-08L00GX-08L00


A350-LF2, Class 1Class 800, SW, Y-Pattern,A350-LF2, Class 1

TS-08L00

TS-08L10


TF-06L00TF-06L10

6


CS-08L20


A350-LF2, Class 1BS-20L00 5

2 – 24 Class 600, RF, RP, Soft Seat,A352-LCC

BF-06L00 5, 6


NT-30S00Alt. NS-30S00, NX-30S00

NOTES

1 Use Sch 160 for pipe NPS 1½ in vibrating service.2 Calculate required wall thickness based on line design pressure and design temperature.3 For use on orifice flange connections only.4 Spectacle blinds may be used up to size 8 NPS. Spades and/or spacers only shall be used in line sizes 10 -

24 NPS.5 Use of ball valves limited to a maximum temperature of 80ºC.6 NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 63 of 83

PIPING CLASS: CSA





NDE: Category III (see Appendix 2)PWHT: All welds (See Note 2)Impact Testing: Not required

ITEM SIZE NPS DESCRIPTION CODE/STD NOTES


½ - 1 ½ Sch 160, PE 32 Sch 160, BE 33 – 8 Sch 80, BE 310 – 24 Calculate thickness, BE 3, 7


3


3




ASMEB16.36

3


Unions ½ - 1½ Use flanges ASMEB16.11


3


½


ASMEB31.3

3

8

Swage ½ - 1½

2 & 3


3


Page 64 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTES



4

Gaskets SPWD, Class 600, RF, 316L SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (e.g.,Flexitallic or equivalent)

ASMEB16.20


ASMEB16.5

Tubing ¼ 0.028” W.T., ASTM A269-316SS,SMLS

⅜ 0.035” W.T., ASTM A269-316SS,SMLS

½ 0.049” W.T., ASTM A269-316SS,SMLS

¾ 0.083” W.T., ASTM A269-316SS,SMLS



ASMEB16.11

3


Page 65 of 83



GS-08S00GX-08S00

2 – 24 Class 600, RF, A216-WCB GF-06S00 9Globe ½ – 1½ Class 800, SW, T-Pattern, A105



TF-06S00

TF-06S10

9

Check ½ – 1½ Class 800, SW, Piston, A105 CS-08S202 – 24 Class 600, RF, Swing, A216-WCB



BS-20S00 1


BF-06S00 1, 9

Butterfly 2 – 24 Class 600, Lug, A216-WCB FL-06S10 9Instrument ½ – 1½ 3000# CWP, Threaded Needle


NOTES



3. All material used must meet the requirements of NACE MR-0175, Latest Edition.4. Spectacle blinds may be used up to size NPS 8. Spades and /or spacers shall only be used in line sizes NPS

10 - 245. The Contractor’s WPS & PQR shall include preheat greater than 38C.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required pipe thickness based on line design pressure and design temperature.8. For use on orifice flange connections only.9. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 66 of 83

PIPING CLASS: CVA


Steam, boiler feed water, blowdownCode: ASME B31.3Flange Rating: ASME Class 600Corrosion Allowance: 1.6 mmTemperature Range: -45 to 290oC Note 6Pressure Limits: 3061 kPa(g) @ -45ºC to -30C Note 6

10204 kPa(g) @ -29ºC to 38C9307 kPa(g) @ 93C9066 kPa(g) @ 148C8756 kPa(g) @ 204C8273 kPa(g) @ 260C7883 kPa(g) @ 290ºC

NDE: Category III (see Appendix 2)PWHT: > 19 mm Wall ThicknessImpact Testing: Not required


B36.10M½ - 1 ½ Sch 160, PE2 - 8 Sch 80, BE10 - 24 Calculated thickness 7

Fittings ½ - 1 ½ 6000#, ASTM A105, SW ASMEB16.11

2 - 24 ASTM A234-WPB, BW ASME B16.9

Flanges ½ - 1 ½ Class 600, RF, ASTM A105, SW ASME B16.5 102 - 24 Class 600, RF, ASTM A105, WN 1014 - 24 Class 600, RTJ, ASTM A105, WN 10

Blinds ½ - 24 Class 600, RF, ASTM A10514 - 24 Class 600, RTJ, ASTM A105

Alternate:clamp joint c/w 17-4 PH SS seal ringwith graphite coating, ASTM A105hubs, A266 CL-3 clamp set, ASTMA193-B7 studs, & ASTM A194-2Hbolts (Grayloc)

ASME B16.5 1

½ - 1 ½ Class 600, SW2 - 24 Class 600, BW


ASMEB16.36


Unions Use flanges



Page 67 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESNipples Pipe ½ - 1½ XXS, PExTE & TExTE, ASTM A106B,

100 mm longXXS, PExTE, ASTM A106B,175 mm long

ASMEB36.10M

8

Swage ½ - 1½

2 & 3




2

Gaskets SPWD, Class 600, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

Soft iron oval or octagonal ring


ASME B16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS3

¾ 0.083” W.T., ASTM A269-316 SS,SMLSFor temperature ≥71ºC & <204ºC:


Tube Fittings For temperature <71ºC:316 SS, short compression type –SwagelokFor temperature ≥71ºC & <204ºC:CS with zinc coating, shortcompression type – Swagelok

4, 5


ASMEB16.11


Page 68 of 83






TF-06A00

TF-06A10

9



NT-60V00Alt. NS-60V00, NX-60V00, NC-60V00

NOTES

1. Reference: Grayloc clamp joint.2. Spectacle blinds may be used up to size 8 NPS. Spades and/or spacers only shall be used in line sizes NPS

10 - 24.3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required wall thickness based on line design pressure and design temperature.8. For use on orifice flange connections only.9. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.10. Refer to paragraph 2.5.6 of this specification for preferred connection methods for steam service.


Page 69 of 83

PIPING CLASS: DAA


Sweet hydrocarbons, produced oil, recycle slop, sales oil, fuel gas, glycol,process vents and drains

Code: ASME B31.3Flange Rating: ASME Class 900Corrosion Allowance: 1.6 mmTemperature Range: -45 to 290C Note 3Pressure Limits: 4590 kPa(g) @ -45C to -30C Note 3

15306 kPa(g) @ -29C to 38C13961 kPa(g) @ 93C13582 kPa(g) @ 149C13100 kPa(g) @ 204C12376 kPa(g) @ 260C11799 kPa(g) @ 290C



B36.10M½ - 1½ Sch 160, PE2 – 3 Sch 80, BE4 – 24 Calculate thickness, BE 4



Flanges ½ - 1½2

Class 1500, RF, ASTM A105, SWClass 1500, RF, ASTM A105, WN

ASMEB16.5

3 – 24 Class 900, RF, ASTM A105, WNBlinds ½ - 2

3 – 24Class 1500, RF, ASTM A105Class 900, RF, ASTM A105

Orifice Flanges ½ - 2

3– 24

Class 1500, RF, WN, ASTM A105, ¾”SW tapClass 900, RF, WN, ASTM A105, ¾”SW tap

ASMEB16.36

C/w bolts, nuts and jack screws

Unions Use flanges



¾

XXS, PExTE & TExTE, ASTM A106B,100 mm longXXS, PExTE, ASTM A106B,175 mm long

ASMEB36.10M

5

Swage ½ - 1½ XXS, PE & TE, ASTM A234-WPB orASTM A105


Page 70 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTES2 & 3 ASTM A234-WPB, PE, - thickness at

both ends to match that of mating pipe


½ - 23– 24

Class 1500, RF, ASTM A516-70NClass 900, RF, ASTM A516-70N

ASMEB16.48

1

Gaskets ½ - 2 SPWD, Class 1500, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

3 - 24 SPWD, Class 900, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent).

ASMEB16.20

Bolting Stud bolt, full thread, ASTM A193-B7,hex nuts, ASTM A194-2H (refer toASME B16.5 for bolt lengths)

ASMEB16.5


⅜ 0.035” W.T., ASTM A269-316 SS,SMLS

½ 0.049” W.T., ASTM A269-316 SS,SMLS

¾ 0.083” W.T., ASTM A269-316 SS,SMLS


Olets ASTM A105 – for types and sizes referto Table 1 Branch Connections inAppendix 3

ASMEB16.11


Page 71 of 83



2 Class 1500, RF, A216-WCB GF-15A003 – 24 Class 900, RF, A216-WCB GF-09A00 6

Globe ½ – 1½ Class 1500, SW, T-Pattern, A105Class 1500, SW, Y-Pattern, A105

TS-15A00TS-15A10

2 Class 1500, RF, T-Pattern,A216-WCBClass 1500, RF, Y-Pattern,A216-WCB

TF-15A00

TF-15A10


TF-09A00

TF-09A10

6

Check ½ – 1½ Class 1500, SW, Piston, A105 CS-15A202 Class 1500, RF, Swing, A216-WCB CF-15A003 – 24 Class 900, RF, Swing, A216-WCB CF-09A00


BS-60A00 2

2 Class 1500, RF, RP, Soft Seat,A216-WCB

BF-15A00


BF-09A00 2, 6


NT-60A00Alt. NS-60A00, NX-60A00

NOTES

1. Spectacle blinds may be used up to size 6 NPS. Spades and/or spacers only shall be used in line sizes NPS 8- 24.


3. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.4. Calculate required wall thickness based on design pressure and design temperature.5. For use on orifice flange connections only.6. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 72 of 83

PIPING CLASS: DLB



13139 kPa(g) @ 200ºCNDE: Category II (see Appendix 2)PWHT: > 19 mm Wall ThicknessImpact Testing: Welds per Box A-4, Table 323.3.1 of ASME B31.3

ITEM SIZENPS



½ – 1½ Sch 160, PE2 – 3 Sch 80, BE4 - 24 Calculate thickness, BE 1


2 – 24 ASTM A420 Gr. WPL6, BW ASMEB16.9


ASMEB16.5

2 Class 1500, RF, ASTM A350-LF2, Class 1,WN



Orifice Flanges ½ - 2 Class 1500, RF, WN, ASTM A350-LF2,Class 1, ¾” SW tap

ASMEB16.36

3 – 24 Class 900, RF, WN, ASTM A350-LF2,Class 1, ¾” SW tapc/w bolts, nuts and jack screws

Unions Use flanges



¾

XXS, PExTE & TExTE, ASTM A333 Gr. 6,100 mm longXXS, PExTE, ASTM A333 Gr. 6,175 mm long

ASMEB36.10M

2


Page 73 of 83

Swage ½ - 1½ XXS, PE & TE, ASTM A420 Gr. WPL6 orASTM A350-LF2, Class1

2 & 3 ASTM A420 Gr. WPL6, PE, - thickness atboth ends to match that of mating pipe



3 – 24 Class 900, RF, ASTM A516-70N 3

Gaskets ½ - 2 SPWD, Class 1500, RF316 SS winding, mica-graphite filler, CScentering ring, 3.2 mm thick(e.g., Flexitallic or equivalent)

ASMEB16.20

3 - 24 SPWD, Class 900, RF316 SS winding, mica-graphite filler, CScentering ring, 3.2 mm thick(e.g., Flexitallic or equivalent)






for types and sizes refer to Table 1 BranchConnections in Appendix 3

VALVES DESCRIPTION TAG NOTESGate ½ – 1½ Class 1500, SW, A350-LF2, Class 1

Class 1500, SWxTE, A350-LF2,Class 1

GS-15L00GX-15L00

2 Class 1500, RF, A352-LCC GF-15L003 – 24 Class 900, RF, A352-LCC GF-09L00 5

Globe ½ – 1½ Class 1500, SW, T-Pattern,A350-LF2, Class 1Class 1500, SW, Y-Pattern,A350-LF2, Class 1

TS-15L00

TS-15L10

2 Class 1500, RF, T-Pattern,A352-LCC

TF-15L00


TF-09L00TF-09L10

5


CS-15L20

2 Class 1500, RF, Swing, A352-LCC CF-15L003 – 24 Class 900, RF, Swing, A352-LCC CF-09L00

Ball ½ – 1½ 6000# CWP, SW, RP, Soft Seat,A350-LF2, Class 1

BS-60L00 4

2 Class 1500, RF, RP, Soft Seat,A352-LCC

BF-15L00

3 – 24 Class 900, RF, RP, Soft Seat,A352-LCC

BF-09L00 4, 5


Page 74 of 83

VALVES DESCRIPTION TAG NOTESInstrument ½ – 1½ 6000# CWP, Threaded Needle


NOTES

1 Calculate required wall thickness based on line design pressure and design temperature.2 For use on orifice flange connections only.3 Spectacle blinds may be used up to size 6 NPS. Spades and/or spacers only shall be used in line sizes 8 -

24 NPS.4 Use of ball valves limited to a maximum temperature of 80ºC.5 NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 75 of 83

PIPING CLASS: DSA





NDE: Category III (see Appendix 2)PWHT: All welds (see Note 2)Impact Testing: Not required


B36.10M½ - 1½ Sch 160, PE 32 Sch 160, BE 33 – 24 Calculate thickness, BE 3, 7


3


3


2 Class 1500, RF, ASTM A105, WN3 – 24 Class 900, RF, ASTM A105, WN 3

Blinds ½ - 2 Class 1500, RF, ASTM A105 33 - 24 Class 900, RF, ASTM A105 3

Orifice Flanges ½ - 2 Class 1500, RF, WN, ASTM A105, ¾”SW tap

ASMEB16.36

3

3 - 24 Class 900, RF, WN, ASTM A105, ¾”SW tapc/w bolts, nuts and jack screws

Unions ½ - 1½ Use flanges ASMEB16.11


3


Page 76 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESNipples Pipe ½ - 1½

¾


ASMEB31.3

3

8

Swage ½ - 1½

2 & 3


3



3 – 24 Class 900, RF, ASTM A516-70N 4

Gaskets ½ - 2 SPWD, Class 1500, RF, 316L SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (e.g.,Flexitallic or equivalent)

ASMEB16.20

3 – 24 SPWD, Class 900, RF, 316L SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (e.g.,Flexitallic or equivalent)


ASMEB16.5

Tubing ¼ 0.028” W.T., ASTM A269-316SS,SMLS

⅜ 0.035” W.T., ASTM A269-316SS,SMLS

½ 0.049” W.T., ASTM A269-316SS,SMLS

¾ 0.083” W.T., ASTM A269-316SS,SMLS



ASMEB16.11

3


Page 77 of 83



GS-15S00GX-15S00

2 Class 1500, RF, A216-WCB GF-15S003 – 24 Class 900, RF, A216-WCB GF-09S00 9


TS-15S00TS-15S10

2 Class 1500, RF, T-Pattern, A216-WCB

TF-15S00


TF-09S00

TF-09S10

9

Check ½ – 1½ Class 1500, SW, Piston, A105 CS-15S202 Class 1500, RF, Swing, A216-WCB CF-15S003 – 24 Class 900, RF, Swing, A216-WCB



BS-60S00 1

2 Class 1500, RF, RP, Soft Seat,A216-WCB

BF-15S00


BF-09S00 1, 9

Butterfly 2 Class 1500, Lug, A216-WCB FL-15S10 93 – 24 Class 900, Lug, A216-WCB FL-09S10


NT-60S00Alt. NS-60S00, NX-60S00

NOTES



3. All material used must meet the requirements of NACE MR-0175, Latest Edition.4. Spectacle blinds may be used up to size NPS 6. Spades and /or spacers shall only be used in line sizes NPS 8

- 245. The Contractor’s WPS & PQR shall include preheat greater than 38C.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required pipe thickness based on line design pressure and design temperature.8. For use on orifice flange connections only.9. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.


Page 78 of 83

PIPING CLASS: DVA


Steam, boiler feed water, blowdownCode: ASME B31.3Flange Rating: ASME Class 900Corrosion Allowance: 1.6 mmTemperature Range: -45 to 344C Note 6Pressure Limits: 4590 kPa(g) @ -45to -30C Note 6

15306 kPa(g) @ 38C13961 kPa(g) @ 93C13582 kPa(g) @ 148C13100 kPa(g) @ 204C12376 kPa(g) @ 260C11307 kPa(g) @ 315C11099 kPa(g) @ 344C

NDE: Category III (see Appendix 2)PWHT: > 19 mm Wall thicknessImpact Testing: Not equired


B36.10M½ - 1½ Sch 160, PE2 – 2½ Sch 80, BE3 Sch 160, BE4 - 24 Calculate thickness, BE 7


2 - 24 ASTM A234-WPB, BW ASMEB16.9

Flanges Raised Face ½ - 1½ Class 1500, RF, ASTM A105, SW ASMEB16.5

1, 10

2 Class 1500, RF, ASTM A105, WN 1, 103 – 24 Class 900, RF, ASTM A105, WN 1, 10

Ring Joint ½ - 1½ Class 1500, RTJ, ASTM A105, SW 102 Class 1500, RTJ, ASTM A105, WN 103 - 24 Class 900, RTJ, ASTM A105, WN 10

Blinds ½ - 2 Class 1500, RF, ASTM A105 13 - 24 Class 900, RF, ASTM A105 1½ - 2 Class 1500, RTJ, ASTM A1053 - 24 Class 900, RTJ, ASTM A105

Clamp Joints Clamp joint c/w 17-4 PH SS seal ringwith graphite coating, ASTM A105hubs, A266 CL-3 clamp set, ASTMA193-B7 studs, & ASTM A194-2Hbolts (Grayloc)

ASMEB16.5

½ - 1½ Class 1500, SW2 Class 1500, BW3 - 24 Class 900, BW

Orifice Flanges ½ - 2 Class 1500, RF, WN, ASTM A105, ¾”SW tap

ASMEB16.36


Page 79 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTES3 - 24 Class 900, RF, WN, ASTM A105, ¾”

SW tapASMEB16.36

C/w bolts, nuts and jack screwsUnions Use flangesPlugs ½ - 1½ Solid hex head, ASTM A105 ASME

B16.11


¾

XXS, PExTE & TExTE, ASTM A106B100 mm longXXS, PExTE, ASTM A106B 175 mmlong

ASMEB36.10M

8

Swage ½ - 1½

2 & 3

XXS, PE &TE, ASTM A234-WPB orASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of matingpipe


1, 2Spectacle Blinds,Spades & Spacers

3 - 24 Class 900, RF, ASTM A516-70N 1, 2Gaskets ½ - 2

3 – 24

½ - 2

3 - 24

SPWD, Class 1500, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent)SPWD, Class 900, RF, 304SSwinding, mica-graphite filler, CScentring ring, 3.2 mm thick (i.e.Flexitallic or equivalent)Class 1500 Soft iron oval oroctagonal ringClass 900 Soft iron oval or octagonalring

ASMEB16.20


ASMEB16.5


SMLS⅜ 0.035” W.T., ASTM A269-316 SS,

SMLS½ 0.049” W.T., ASTM A269-316 SS,

SMLS3



Tube Fittings For temperature <71ºC:316 SS, short compression type -SwagelokFor temperature ≥71ºC & <204ºC:


Page 80 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESCS with zinc coating, shortcompression type - Swagelok

4, 5


ASMEB16.11


Class 1500, SWxTE, A105GS-15V00GX-15V00

2 Class 1500, BW, A216-WCB GB-15V003 – 24 Class 900, BW, A216-WCB GB-09V00 9


TS-15V00TS-15V10

2 Class 1500, BW, T-Pattern, A216-WCB

TB-15V00

3 – 24 Class 900, BW, T-Pattern,A216-WCBClass 900, BW, Y-Pattern,A216-WCB

TB-09V00

TB-09V10

9

Check ½ – 1½ Class 1500, SW, Piston, A105 CS-15V202 Class 1500, BW, Swing, A216-WCB CB-15V003 – 24 Class 900, BW, Swing, A216-WCB CB-09V00


NT-60V00Alt. NS-60V00, NX-60V00

NOTES

1. Raised face flanges are not preferred in steam service.2. Spectacle blinds may be used up to size 6 NPS. Spades and/or spacers only shall be used in line sizes NPS 8

- 24.3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required wall thickness based on design pressure and temperature.8. For use on orifice flange connections only.9. NPS 6” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.10. Refer to paragraph 2.5.6 of this specification for preferred connection methods for steam service.


Page 81 of 83

PIPING CLASS: EVADESIGN BASISService: Steam

Steam, boiler feed water, blowdownCode: ASME B31.3Flange Rating: ASME Class 1500Corrosion Allowance: 1.6 mmTemperature Range: -45 to 344C Note 6Pressure Limits: 7663 kPa(g) @ -45to -30C Note 6

25545 kPa(g) @ 38C23270 kPa(g) @ 93C22615 kPa(g) @ 148C21856 kPa(g) @ 204C20650 kPa(g) @ 260C18857 kPa(g) @ 315C18509 kPa(g) @ 344C

NDE: Category III (see Appendix 2)PWHT: > 19 mm Wall thicknessImpact Testing: Not required


B36.10M½ - 1½ Sch 160, PE2 – 3 Sch 160, BE4 - 24 Calculate thickness, BE 7


2 - 24 ASTM A234-WPB, BW ASMEB16.9

Flanges Raised Face 2 - 12 Class 1500, RF, ASTM A105, WN ASMEB16.5

11

Ring Joint ½ - 1½ Class 1500, RTJ, ASTM A105, SW 112 – 24 Class 1500, RTJ, ASTM A105, WN 11

Blinds ½ - 24 Class 1500, RF, ASTM A105½ - 24 Class 1500, RTJ, ASTM A105

Clamp Joints Clamp joint c/w 17-4 PH SS seal ringwith graphite coating, ASTM A105hubs, A266 CL-3 clamp set, ASTMA193-B7 studs, & ASTM A194-2Hbolts (Grayloc)

ASMEB16.5

1

½ - 1½ Class 1500, SW2 - 24 Class 1500, BW

Blinds 2 – 24 Clamp joint c/w 1 BW Hub & BlindHub, 17-4 PH SS seal ring withgraphite coating, ASTM A105 hubs,A266 CL-3 clamp set, ASTM A193-B7studs, & ASTM A194-2H nuts(Grayloc)

Orifice Flanges ½ - 24 Class 1500, RTJ, WN, ASTM A105,¾” SW tap

ASMEB16.36

C/w bolts, nuts and jack screwsUnions Use flanges


Page 82 of 83

ITEM SIZE NPS DESCRIPTION CODE/STD NOTESPlugs ½ - 1½ Solid hex head, ASTM A105 ASME

B16.11Nipples Pipe ½ - 1½

¾

XXS, PExTE & TExTE, ASTM A106B100 mm longXXS, PExTE, ASTM A106B 175 mmlong

ASMEB36.10M

8

Swage ½ - 1½

2 & 3

XXS, PE &TE, ASTM A234-WPB orASTM A105ASTM A234-WPB, PE – thickness atboth ends to match that of matingpipe


½ - 1½ Class 1500, RTJ, ASTM A516-70N ASMEB16.48

2

Gaskets 2 - 12

½ - 24

Class 1500, Grafoil filled with CSouter ring and 304SS inner ring(Reference: Flexitallic)Class 1500, Soft iron oval oroctagonal ring

ASMEB16.20


ASMEB16.5


SMLS⅜ 0.065” W.T., ASTM A269-316 SS,

SMLS½ 0.065” W.T., ASTM A269-316 SS,

SMLS3



Tube Fittings For temperature <71ºC:316 SS, short compression type -SwagelokFor temperature ≥71ºC & <204ºC:CS with zinc coating, shortcompression type - Swagelok

4, 5

Olets ASTM A105 - for types and sizesrefer to Table 1 Branch Connectionsin Appendix 3

ASMEB16.11


Page 83 of 83


Class 1500, SWxTE, A105GS-15V00GX-15V00

2 – 24 Class 1500, BW, A216-WCB GB-15V00 9Globe ½ – 1½ Class 1500, SW, Y-Pattern, A105 TS-15V10

2 – 24 Class 1500, BW, Y-Pattern,A216-WCB

TB-15V10 9

Check ½ – 1½ Class 1500, SW, Piston, A105 CS-15V202 – 242 – 12

Class 1500, BW, Swing, A216-WCBClass 1500, Wafer, A216-WCB(Severe Service, Ref. CG Industrial)

CB-15V00CW-15V60

Butterfly 2 - 24 Class 1500, Lug, Resilient Seat,A216-WCB

FL-15V00 10


NT-60V00Alt. NS-60V00, NX-60V00

NOTES

1. Preferred joint.2. Spectacle blinds may be used up to size 6 NPS. Spades and/or spacers only shall be used in line sizes NPS 8

- 24.3. Preferred size.4. HRB less than or equal to 72.5. By exception, where installation detail specifies metallurgy.6. Subject to Fig. 323.2.2B of ASME B31.3, latest edition.7. Calculate required wall thickness based on design pressure and temperature.8. For use on orifice flange connections only.9. NPS 4” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.10. NPS 8” and above to be supplied with a gear operator. Tag to be suffixed with “-GO”.11. Refer to paragraph 2.5.6 of this specification for preferred connection methods for steam service.

ORBU-SPC-44-0-22Appendix 2Page 1 of 1

APPENDIX 2 - NON-DESTRUCTIVE EXAMINATION

Category I

Inspection required for Normal Fluid Service as per ASME B31.3, Section 341.4.

Category II

Inspection required for Normal Fluid Service as per ASME B31.3, Section 341.4, with the following exception: 10% (min) of all butt welds shall be 100% examined by radiography.

Category III

Inspection required for Normal Fluid Service as per ASME B31.3, Section 341.4, with the following exceptions: 100% of all butt welds shall be examined 100% by radiography. 5% of all socket welds shall be examined 100% by radiography to ensure 1.6 mm gap. 100% of all socketwelds shall be examined 100% by magnetic particle or liquid penetrant examination.

Category IV

Inspection required for Category D Fluid Service as per ASME B31.3, Section 341.4.

Category V

Inspection required for Normal Fluid Service as per ASME B31.3, Section 341.4, with the following exceptions: 10% (min) of all butt welds shall be examined 100% by radiography. 100% of all joints shall be examined visually.

Category VI

Inspection required for Normal Fluid Service as per ASME B31.3, Section A341.4, with the following exceptions: 100% of all joints shall be examined visually.

ORBU-SPC-44-0-22Appendix 3Page 1 of 1

APPENDIX 3 – BRANCH CONNECTIONSTABLE 1 BRANCH CONNECTIONS

Branch Pipe Size (NPS)½ ¾ 1 1 ½ 2 3 4 6 8 10 12 14 16 18 20 24

½ T¾ T T1 T T T1 ½ T T T T2 T T3 T T4 WOL T T6 WOL T T T8 WOL WOL T T T10 WOL WOL T T T T12 WOL WOL WOL T T T T14 WOL WOL WOL T T T T T16 WOL WOL WOL T T T T T T18 WOL WOL WOL WOL T T T T T T20 WOL WOL WOL WOL T T T T T T T

Hea

der S

ize

(NPS

)

24

TOL or SOL(Note: elbolets orlatrolets may beused subject to

Owner’s approval)

WOL WOL WOL WOL WOL T T T T T T T

Applicable Line Classifications: AAA, AAB, AAG, ABA, ACA, ACC, ASA, AVA, BAA, BBA, BBZ, BSA, BVA, CAA,CAZ, CBA, CVA, DAA, DVA, EVA

TABLE 2 BRANCH CONNECTIONSBranch Pipe Size (NPS)

½ ¾ 1 1 ½ 2 3 4 6 8 10 12 14 16 18 20 24½ T¾ T T1 T T T1 ½ T T T T2 SOL SOL SOL T T3 SOL SOL SOL SOL T T4 SOL SOL SOL SOL WOL T T6 SOL SOL SOL SOL WOL T T T8 SOL SOL SOL SOL WOL WOL T T T10 SOL SOL SOL SOL WOL WOL T T T T12 SOL SOL SOL SOL WOL WOL WOL T T T T14 SOL SOL SOL SOL WOL WOL WOL T T T T T16 SOL SOL SOL SOL WOL WOL WOL T T T T T T18 SOL SOL SOL SOL WOL WOL WOL WOL T T T T T T20 SOL SOL SOL SOL WOL WOL WOL WOL T T T T T T T

Hea

der S

ize

(NPS

)

24 SOL SOL SOL SOL WOL WOL WOL WOL WOL T T T T T T TApplicable Line Classifications: ALB, AWA, BLB, CLB

T = Straight or reducing teeTOL = ThreadoletSOL = SockoletWOL = WeldoletNote: All branch connections shall be PWHT as per the criteria defined by ASME B31.3 Section 331.1.3

ORBU-SPC-44-0-22

Documents

asme b16

asme b36

asme b31

asme section v

alberta regulation

commodity codes

following codes

safety codes act