Cartridge & Bag Filter Media Reference Guide 3725 Interpark Drive Colorado Springs, CO 80907 Phone: 719-260-5694 • Fax: 719-260-5944 www.optimumfilter.com For inquiries of our complete line of Industrial, High Purity and Sanitary Filter Housings visit www.optimumfilter.com
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Pleated Polypropylene Cartridges are designed for use in most applications where absolute rated pleated ltration is needed Designed to hold 65 square feet of ltration media our High Purity - PP Cartridge is a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Eciency ratings to 9998 (Beta 5000)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
Filtration MediaSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
I = Stainless Steel Insert
HP = Heavy Poly Core
FG = Glass Reinforced PP Core
SS = Stainless Steel Core
R = 18 Megohm Rinse
Adders-B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
O-RingsGaskets2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
5 = 222 w Spring
6 = 226 w Flat Cap
7 = 226 w Fin
8 = 226 w Spring
16 = 213 Internal O-Ring
End Cap CodeC10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
LengthA02
045
10
20
50
100
200
400
Pore SizePP
Ordering Information
2
Filter Data Sheet
Economy - PPPleated Polypropylene Cartridge
Economy Pleated Polypropylene Cartridges
oer a highly ecient and cost-eective ltration
option for use in a wide variety of applications
These cartridges are constructed of 100
polypropylene materials and are assembled using
the latest thermal-bonding equipment Cartridges
are oered in DOE and 222 end congurations as
well as in both nominal (90) and absolute (to
9998) retention eciencies
Flow Rate
02
045
10 + 20 + 50
100 + 200
400
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
18
16
14
12
10
8
6
4
200
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D)
Typical ApplicationsFood amp BeveragePhotographicDeionized WaterRO MembranePre-FiltrationProcess Water
Fine Chemicals Process Plating Chemicals Wastewater Produced WaterCosmetics
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Pleated Polypropylene Cartridges are designed for use in most applications where absolute rated pleated ltration is needed Designed to hold 65 square feet of ltration media our High Purity - PP Cartridge is a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Eciency ratings to 9998 (Beta 5000)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
Filtration MediaSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
I = Stainless Steel Insert
HP = Heavy Poly Core
FG = Glass Reinforced PP Core
SS = Stainless Steel Core
R = 18 Megohm Rinse
Adders-B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
O-RingsGaskets2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
5 = 222 w Spring
6 = 226 w Flat Cap
7 = 226 w Fin
8 = 226 w Spring
16 = 213 Internal O-Ring
End Cap CodeC10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
LengthA02
045
10
20
50
100
200
400
Pore SizePP
Ordering Information
2
Filter Data Sheet
Economy - PPPleated Polypropylene Cartridge
Economy Pleated Polypropylene Cartridges
oer a highly ecient and cost-eective ltration
option for use in a wide variety of applications
These cartridges are constructed of 100
polypropylene materials and are assembled using
the latest thermal-bonding equipment Cartridges
are oered in DOE and 222 end congurations as
well as in both nominal (90) and absolute (to
9998) retention eciencies
Flow Rate
02
045
10 + 20 + 50
100 + 200
400
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
18
16
14
12
10
8
6
4
200
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D)
Typical ApplicationsFood amp BeveragePhotographicDeionized WaterRO MembranePre-FiltrationProcess Water
Fine Chemicals Process Plating Chemicals Wastewater Produced WaterCosmetics
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Pleated Polypropylene Cartridges are designed for use in most applications where absolute rated pleated ltration is needed Designed to hold 65 square feet of ltration media our High Purity - PP Cartridge is a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Eciency ratings to 9998 (Beta 5000)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
Filtration MediaSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
I = Stainless Steel Insert
HP = Heavy Poly Core
FG = Glass Reinforced PP Core
SS = Stainless Steel Core
R = 18 Megohm Rinse
Adders-B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
O-RingsGaskets2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
5 = 222 w Spring
6 = 226 w Flat Cap
7 = 226 w Fin
8 = 226 w Spring
16 = 213 Internal O-Ring
End Cap CodeC10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
LengthA02
045
10
20
50
100
200
400
Pore SizePP
Ordering Information
2
Filter Data Sheet
Economy - PPPleated Polypropylene Cartridge
Economy Pleated Polypropylene Cartridges
oer a highly ecient and cost-eective ltration
option for use in a wide variety of applications
These cartridges are constructed of 100
polypropylene materials and are assembled using
the latest thermal-bonding equipment Cartridges
are oered in DOE and 222 end congurations as
well as in both nominal (90) and absolute (to
9998) retention eciencies
Flow Rate
02
045
10 + 20 + 50
100 + 200
400
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
18
16
14
12
10
8
6
4
200
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D)
Typical ApplicationsFood amp BeveragePhotographicDeionized WaterRO MembranePre-FiltrationProcess Water
Fine Chemicals Process Plating Chemicals Wastewater Produced WaterCosmetics
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Pleated Polypropylene Cartridges are designed for use in most applications where absolute rated pleated ltration is needed Designed to hold 65 square feet of ltration media our High Purity - PP Cartridge is a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Eciency ratings to 9998 (Beta 5000)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
Filtration MediaSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
I = Stainless Steel Insert
HP = Heavy Poly Core
FG = Glass Reinforced PP Core
SS = Stainless Steel Core
R = 18 Megohm Rinse
Adders-B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
O-RingsGaskets2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
5 = 222 w Spring
6 = 226 w Flat Cap
7 = 226 w Fin
8 = 226 w Spring
16 = 213 Internal O-Ring
End Cap CodeC10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
LengthA02
045
10
20
50
100
200
400
Pore SizePP
Ordering Information
2
Filter Data Sheet
Economy - PPPleated Polypropylene Cartridge
Economy Pleated Polypropylene Cartridges
oer a highly ecient and cost-eective ltration
option for use in a wide variety of applications
These cartridges are constructed of 100
polypropylene materials and are assembled using
the latest thermal-bonding equipment Cartridges
are oered in DOE and 222 end congurations as
well as in both nominal (90) and absolute (to
9998) retention eciencies
Flow Rate
02
045
10 + 20 + 50
100 + 200
400
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
18
16
14
12
10
8
6
4
200
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D)
Typical ApplicationsFood amp BeveragePhotographicDeionized WaterRO MembranePre-FiltrationProcess Water
Fine Chemicals Process Plating Chemicals Wastewater Produced WaterCosmetics
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
bull 100 cellulose-free constructionbull Pleated design offers significantly increased surface area and loading capacity when compared to depth cartridges (string-wound Meltblown and resin- bonded)bull Excellent compatibility with a wide range of chemicals and sanitizing agentsbull High flow rates at low pressure dropsbull Plastisol (PVC) end caps gaskets offer positive sealbull All cartridges are manufactured with a polypropylene outer nettingbull Wide variety of micron ratings (035 - 50) and lengths (975rdquondash 40rdquo) available
Maximum Recommended Operating Conditions Dierential Pressure20-25 PSIDTemperature140˚ F (60˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
PurityLiquidClear cartridges are produced using 100 synthetic fibers which are free of binders or adhesives
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Pleated Microglass Cartridges oer an economical absolute rated ltration solution for both liquids and gases They oer excellent ow rates and long service life with an excep-tional ability to retain both deformable and non-deformable particlesHigh Purity - FG Cartridges are constructed with absolute rated borosilicate microglass media that oers high dirt-loading capacities The natural positive charge of the glass also aids in the retention of negatively charged particulates such as bacteria endotoxins and a variety of colloidal materials Eciency ratings to 9998 (Beta 5000)
Flow Rate
0 38 76 114 152 190 228 266 304
0 1 2 3 4 5 6 7 8
07
06
05
04
03
02
01
00
10 inch (250 mm) CartridgesWater Flow Rate (LPM)
Water Flow Rate (GPM)
Di
eren
tial P
ress
ure
(PSI
D) 02
045
10 + 2050 + 100
200 + 400
Typical Applications
Construction MaterialsFiltration Media-FDA Borosilicate Microglass with acrylic binder
Support MediandashSpun-bonded polyester laminated on both upstream and downstream sidesEnd CapsPolypropylene Center CoreFiberglassOuter Support CagePolypropyleneO-RingsGasketsBuna Viton EPDM Silicone
Teonreg Encapsulated VitonNote Contact factory for information on high- temperature stainless construction options
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter275 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out∆P 35 PSITemperature200degF (93degC)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121degC for plastics
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80ordmC for 30 min121degC for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
Note Optional High Temperature Construction available
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Economy Pleated Microglass Cartridges oer a highly ecient and cost-eective ltration option for use in a wide variety of applications These cartridges are constructed of FDA materials and are assembled using the latest thermal-bonding equipment Cartridges are oered in DOE and 222 end congurations as well as in both nominal (90) and absolute (to 9998) retention eciencies
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity - Polysulfone (PS) MembraneHydrophilic Polysulfone Membrane for Water and Aqueous Solutions
bull Highly asymmetric polysulfone membrane mediabull Absolute rated at gt999 efficiency with retention ratings from 005 to 12 μmbull Superior flow rates and long service lifebull High purity polypropylene hardwarebull End configurations to fit most vesselsbull Rinse-up to 18 megohm with a minimum throughputbull Pre-rinse option availablebull Surface area = 61 ft 2 (057 m2) per 10rdquo (254 cm)
Typical ApplicationsDeionized Water SystemsGeneral-Use Water FiltrationLiquid ClarificationRecirculating FluidsChemical Filtration
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teflonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity - Bio-Burden Reduction Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Bio-Burden Reduction in Food amp Beverage and Pharmaceutical Applications
BRPES Bio-Burden Reduction Grade filter cartridges are validated and 100 integrity-tested providing bio-burden and small particle removal across a wide range of food amp beverage biological liquids and intermediate bulk pharmaceutical fluids The BRPES series is constructed using a unique single-layer hydrophilic asymmetric polyethersulfone membrane This construction offers broad chemical compatibility high flow-rates at low pressure drops and low extractables
BRPES cartridges are validated in accordance with HIMA and ASTM F838‐05 protocols for determination of bacterial retention in liquid filtration Sterile effluent was achieved with challenge concentration levels in excess of 107 organisms per cm2 of filter areabull 02μm Brevundimonas diminutabull 045μm Lactobacillus lindneri Serratia marcescensbull 065μm Lactobacillus lindneri Saccharomyces
cerevisiae
Typical Applicationsbull Cell Culture Mediabull Large Volume Parenterals (LVPrsquos)bull Pharmaceutical Bulk Chemical SolutionsbullDiagnosticsbull Blood and Serum Fractionsbull Purified Waterbull Beer Wine and Spiritsbull Juice amp Soft Drinksbull Bottled Water
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
BRPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
045 20rdquo (508 cm) 3 = 222 w Fin E = EPDM
065 30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity - Pharmaceutical Grade PESHydrophilic Polyethersulfone Membrane Cartridges for Pharmaceutical and Biological Applications
PPES Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane along with exceptional flow rate vs pressure drop makes the PPES series the ideal choice for a variety of valuable andor critical pharmaceutical solutions
PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
Typical Applicationsbull Vaccinesbull Large Volume Parenteral (LVPrsquos)bull Water for Injection (WFI)bull Diagnosticsbull Ophthalmicsbull Cell and Tissue Culture Mediabull Protein Solutionsbull Serum and Blood Products
Construction MaterialsMembrane PolyethersulfoneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SterilizationHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
max ΔP 7 psi 100 cycles
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPES Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 10rdquo (254 cm) 2 = DOE Flat Gasket B = Buna-N
20rdquo (508 cm) 3 = 222 w Fin E = EPDM
30rdquo (762 cm) 4 = 222 w Flat Cap S = Silicone
40rdquo (1016 cm) 6 = 226 w Flat Cap V = Vitonreg
7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 176degF (80degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
29 PSI (2 bar) at 176degF (80degC)
Reverse 29 PSI (2 bar)
FDA Listed MaterialsManufactured from materials which are listed
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity- Pharmaceutical Grade PTFEHydrophobic PTFE Membrane Cartridges for Sterilizing in Pharmaceuticals amp Biotechnology Applications
Typical Applicationsbull Sterile gas filtration of fermentor inletsbullOff‐gassing downstream of fermentors and
bioreactorsbullAutoclave vent filtersbullWFI tank ventsbull Sterile air supply for service gases (ie filling
lines in blow‐fill‐seal systems)Construction MaterialsMembrane PTFEPrefiltration Media PolypropyleneSupport Layers PolypropyleneCageCoreAdapters PolypropyleneSeals Buna EPDM Silicone
Vitonreg Teflonreg Encapsulated Vitonreg
SanitizationSterilizationIn-Line Steaming 134degC 30 min max ΔP 7
psiHot Water 85deg- 95degC 30 min max ΔP 7 psiIn-Line Steaming 134degC 30 min
DimensionsLength5 to 40 inches (127 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
PPTFE Rating (micro) A Length Nominal C End Cap Style O-RingsGaskets02 5rdquo (127 cm) 2 = DOE Flat Gasket B = Buna-N
10rdquo (254 cm) 3 = 222 w Fin E = EPDM
20rdquo (508 cm) 4 = 222 w Flat Cap S = Silicone
30rdquo (762 cm) 6 = 226 w Flat Cap V = Vitonreg
40rdquo (1016 cm) 7 = 226 w Fin T = Teflonreg Encapsulated Vitonreg
Ordering Information
Maximum Recommended Operating ConditionsTemperature 284degF (140degC)
Forward 72 PSI (5 bar) at 68˚F (20degC)
7 PSI (05 bar) at 284degF (140degC)
Reverse 44 PSI (3 bar) at 68degF (20degC)
7 PSI (05 bar) at 284degF (140degC)
FDA Listed MaterialsManufactured from materials which are listed
for food contact applications in Title 21 of the
US Code of Federal Regulations
0 50 100 150 200 250 300
Air Flow Rate (SCFM)
Del
ta-P
(PSI
D)
50
40
30
20
10
00
PPTFE Pharmaceutical Grade sterilizing
filter cartridges provide optimized filtration
performance in sterile airgas and venting
applications The single layer PTFE membrane
with over double the hydrophobicity of
polypropylene or PVDF is the best choice
to prevent water intrusion and resulting
microbial growth
Each PPTFE cartridge is integrity tested
during manufacturing and is supported by a
validation guide for regulatory compliance
PPTFE elements are fully validated as sterilizing
grade filters in accordance with HIMA and
ASTM F838-05 guidelines Sterile effluent
was achieved with challenge concentration
levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash Water Service Grade PESHydrophilic Polyethersulfone (PES) Membrane for Water Purication
Water Service Grade PES Cartridges are cost eective alternatives to General and Electronic Grade Cartridges for a variety of aqueous based uids Water Service Cartridges are manufac-tured from an inherently hydrophilic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash General Grade PESHydrophilic Polyethersulfone (PES) Membrane for Liquid Applications
General Grade PES Cartridges are designed for general purpose use wherever a cost eective membrane lter is required Manufac-tured to hold the maximum amount of lter media that can be completely and eectively utilized in a cartridge General Grade Cartridges are manufactured from an inherently hydro-philic PES membrane These cartridges oer excellent ow characteristics extended service life and broad chemical compatibility
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash Electronics Grade PESHydrophilic Polyethersulfone (PES) Membrane for Electronics Applications
Electronics Grade PES Cartridges are designed to meet the special needs of the electronics and high purity chemical industries Polyethersulfone membrane cartridges are resistant to most acids and bases capable of handling strong sanitization agents High ow rates make polyethersulfone a good choice for Ultra-Pure water systems Each cartridge is ushed with 18 megohm high purity water to minimize extractable Each cartridge is also individually integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash Food and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed for the Food and Beverage Industry
Food and Beverage Grade PES Cartridges have been designed to comply with all FDA requirements for the food industry Polyether-sulfone is a low protein binding membrane and therefore a good choice for fermented bever-age applications Food and Beverage Cartridges are ushed with DI water to remove manufac-turing debris and extractable Each cartridge module is tested to ensure integrity
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsTemperature176˚F (80˚C)
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFPES Pore Size
004
01
02
045
065
08
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Data Sheet
15
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Visit our website for other SVampE productsincluding Cartridge and Bag Filter Media Stainless Steel Filter
Housings Sanitary Y-Strainers amp Custom Tanks amp Vesselsand a variety of Water Treatment Equipment components
High Purity - Wine and Beverage Grade PESHydrophilic Polyethersulfone (PES) Membrane Developed Specically for the Wine and Beverage Industries
Wine and Beverage Grade PES cartridges provide signicant reduction of yeast and bacteria delivering critical spoilage prevention to wine producers A layer of microporous pleated polypropylene depth media combines ne particulate retention with high contaminant-holding capacity The secondary PES membrane layer provides nal retention The combination of high-ow capacity and extraordinary retention make this series ideally suited for wine and beverage production
For wine production typical application of a 065 micron GBPES element as a prelter or nal polishing lter provides removal of all yeast and multi-log reduction of Lactobacillus Plantarum and other common microbes Retention of Serattia Marcescans by LRV 7 is achieved by the 045 micron GBPES element
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash General Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Liquid Applications
General Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process General Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants These cartridges are designed to hold the maximum amount of Nylon 66 membrane that can be eectively utilized in a cartridge
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cyclesChemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGHNY
GGHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash Electronics Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for Electronics Applications
Electronics Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Electronics Grade Cartridges are available in both our standard and Plus+ grades The Plus+ grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Electronics Grade Cartridges are ushed with 18 megohm high purity water to minimize extract-able Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GEHNY
GEHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity ndash Food and Beverage Grade Nylon 66 and Plus+ Nylon 66Hydrophilic Nylon 66 for the Food and Beverage Industry
Food and Beverage Grade Nylon 66 Cartridges are naturally hydrophilic requiring no surface treatments that can leach into your process Food and Beverage Grade Cartridges are designed to comply with all FDA require-ments for food contact Available in both our standard and Plus+ grades The Plus+grade membrane is modied with a high positive charge for removal of endotoxins and small negatively charged contaminants All Food and Beverage Grade Cartridges are ushed with DI water to minimize extractable Cartridges are also integrity tested
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GFHNY
GFHNY+
Pore Size
003
005
01
02
045
065
08
12
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Buna Viton EPDM Silicone Teonreg Encapsulated Viton
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFiltered Hot WaterSteam Sterilization
80˚C for 30 min121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitiz-ing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
Maximum Dierential PressuresForward50 PSI (34 bar) at 20˚CReverse40 PSI (27 bar) at 20˚C
GGPTFE Pore Size
01
02
045
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
16 = 213 Internal O-Ring
O-RingsGaskets -
B = Buna
E = EPDM
S = Silicone
V = Viton
T = Teonreg Encapsulated Viton
I = Stainless Steel Insert
Adders
Ordering Information
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
High Purity - FluoroClear Pleated All-Fluorocarbon
FluoroClear Cartridges are designed for highly aggressive wet-etch and cleaning applications FluoroClear cartridges are constructed with 100 uorocarbon materials providing broad chemical compatibility and temperature resistance The PTFE membrane delivers high ow rates and high purity euent at low pressure drops Cartridges are available as ushed amp dried or as wet-packed (6040 DI WaterIPA Solution) FluoroClear cartridges are manufactured in a cleanroom environment to ensure product cleanliness
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
MembraneSupport MediaEnd CapsCenter CoreOuter Support CageO-RingsGaskets
Construction Materials
SanitizationSterilizationFluoroClear cartridges may be sanitized using compatible chemical agentsFluoroClear cartridges may not be autoclaved or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsTemperature215˚F (102˚C)
Maximum Dierential PressuresForward60 PSI (414 bar) at 70˚F (21˚C)Reverse30 PSI (207 bar) at 70˚F (21˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specications for biological safety per USP Class VI ndash 121˚C for plastics
le 5 cc min at 40 psig (276 bar)le 5 cc min at 40 psig (276 bar)le 5 cc min at 30 psig (207 bar)le 5 cc min at 20 psig (138 bar)le 5 cc min at 15 psig (138 bar)
GFL Pore Size (μm)
005
01
02
04
10
A Length
10 (254 cm)
20 (508 cm)
30 (762 cm)
40 (1016 cm)
C End Cap Code
2 = DOE Flat Gasket
3 = 222 w Fin
4 = 222 w Flat Cap
6 = 226 w Flat Cap
7 = 226 w Fin
O-RingsGaskets -
T = Teonreg Encapsulated Viton E = Flushed amp Dried
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
in the construction of the Bi-Component Filter Cartridgesbond forms a very stable porosity The patented construction process of these Bi-Component Filter Cartridges provides
variability and media migration
Typical Applications
Food and Beverage Resins
PolypropyleneFiltration MediaEnd Caps
Construction Materials DimensionsLength975 to 40 inches (248 to 102 cm)Outside Diameter26 inches (66 cm)Inside Diameter11 inch (28 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating Conditions
80 PSITemperature176degF (80degC)
Purity
wetting agents binders and silicone
The rigid construction also provides a three
unique feature also prevents changes in
and ensures against contaminant unload-ing
GPB Micron Rating - Length - End Cap Code O-RingsGaskets
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
bull Unique amp proprietary process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene constructionbull All end congurations available (glued or thermally-bonded)
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Water Grade BB - Size Polypropylene Meltblown Cartridge - GWTB
bull Unique amp production process delivers eciency life and economybull Excellent compatibility with a wide range of chemicalsbull Graded density pore structure enhances dirt holding capacitybull Easy cartridge incineration and disposalbull All polypropylene construction
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
consistent performancebull Excellent compatibility with a wide range of chemicalsbull Easy cartridge incineration and disposalbull All polypropylene constructionbull thermally-bonded)bull Resists contaminant unloading even at
bull Grooved exterior increases surface area
Micron Ratings1 3 5 10 20 30 50 75 100
1 Micron 955-100 Micron 99
PolypropylenePolypropyleneSilicone Buna
Polyfoam EPDM Viton
Filtration MediaEnd CapsO-RingsGaskets
Construction Materials
Dimensions (Nominal)Length975 to 40 inches
(248 to 102 cm)Outside Diameter25 inches (64 cm)Inside Diameter1 inch (26 cm)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
Maximum Recommended Operating ConditionsForward35 PSIDReverse25 PSID
20 PSIDTemperature140degF (60degC)
Purity
additives wetting agents binders and silicone
Filter Grade (microm) DI Water Flow per 1 PSID (gpm10rdquo (254 cm) equivalent)
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
bull Available in a wide variety of lengths and micron ratings from 975 to 50 inches and 05-400 micrombull Medias to t all applications including polypropylene bleached cotton FDA bleached cotton natural cotton polyester nylon and glassbull Core materials include polypropylene 304 amp 316 stainless steel tin and glassbull Performance-enhancing end-congurations available to t every process requirement
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
GEM Reverse Osmosis Membranes provide the high salt rejection and ow rates typically available on composite membranes while providing superior value This gives the membrane user an edge by providing reduced costs for the operation of a reverse osmosis system The pre-ltration program oered by Optimum Filter in conjunction with the GEM elements may eliminate the need for costly membrane cleanings These elements are manufactured utilizing an ISO 90012000 Certied Quality Management System
Typical Applications Producing boiler make-up Water for power plants Blow-down from power plants Desalting of well water for municipal drinking water supplies Reducing TDS prior to ion-exchange Purifying water to ultrapure standards for semiconductor and microelectronics manufacturing facilities
Application DataMax Applied Pressure600 PSIG (416 MPa) Max Chlorine Concentrationlt01 PPMMax Operating Temperature113˚F (45˚C)Feedwater pH Range30 - 100Max Feedwater Turbidity10 NTUMax Feedwater SDI (15 mins)50Max Feed Flow75 GPM (170 m3h)Max Ratio of Concentrate to Permeate Flow for any Element51Max Pressure Drop for Each Element10 PSI
The limitations shown here are for general use The values may be more conservative for specic projects to ensure the best performance and longest life of the membrane Performance
Permeate Flow8900 to 14000 GPDSalt Rejection Minimum98
Test ConditionsThe stated performance is initial (data taken after 30 minutes of operation) based on the following conditionsNaCI Test Solution1500 PPMApplied Pressure225 PSI (155 MPa)Operating Temperature77˚F (25˚C)Permeate Recovery15pH Range65 - 70
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Ordering Information Micron Rating OptionsCoverJacket
P = Plain (No Cover) NR = No ring
Bag Dimensions
Size Diam Length
1 = 706 165
2 = 706 320
3 = 412 80
4 = 412 140
7 = 55 150
8 = 55 200
9 = 55 310
C1 = 731 165
C2 = 731 325
Ring Type
S = Standard steel ring
SS = Stainless steel ring
C = Comm type snap steel band
1-1500
DIRTY FLUID CLEAN FLUID
G
RC = Rev collar (S amp SS only)
12 = 80 300
Micron Ratings 1 5 10 25 50 75 100 125 150
Mesh Materials
bull bull bull bull bull bull bull bullbull bull
Mesh Bag StylesS-ring bags have a galvanized steel ring (stainless steel optional) sewn into the top of the bag They are supplied with sewn seams standard
V-ring bags have a specially-designed high-temperature snap-seal ring sewn into the top of the bag They are supplied with sewn seams standard
bull Micron ratings from 1 to 1500bull All industry-standard and custom sizes availablebull High flowlow pressure drop mediabull Surface-retention filtrationbull Wide chemical compatibilitybull Sewn constructionbull Handles standard on all bagsbull Choice of steel or molded plastic snap seal ringsbull Economical removal of non-deformable contami nantsbull Non-fiber sheddingbull High removal efficiencybull Temperature ratings to 400ordmF (204ordmC)bull Meet FDA regulations for contact under Title 21 Section 1771520bull Silicone-free construction
Multilament Mesh media is woven from threads made of smaller fibers Bags made from this material are low cost and disposable
Monolament Mesh is woven from single-fiber threads The openings are square and uniform Bags made from this material have excellent strength and some are cleanable
31
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Visit our website for other SVampE productsincluding Cartridge and Bag Filter Media Stainless Steel Filter
Housings Sanitary Y-Strainers amp Custom Tanks amp Vesselsand a variety of Water Treatment Equipment components
32
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert
Visit our website for other SVampE productsincluding Cartridge and Bag Filter Media Stainless Steel Filter
Housings Sanitary Y-Strainers amp Custom Tanks amp Vesselsand a variety of Water Treatment Equipment components
Filter Data Sheet
High Purity - OPPPleated Polypropylene Cartridge for Beverage Applications
Pleated Polypropylene Cartridges are designed for use in beverage applications where economical absolute rated pleated filtration is needed Designed to hold 65 square feet of filtration media our High Purity - OPP cartridges are a great value These cartridges are constructed with 100 polypropylene materials and assembled using the latest thermal bonding equipment Efficiency ratings to 99
Process WaterFine Chemicals Plating Chemicals Wastewater
Construction MaterialsFiltration Media PolypropyleneSupport Media PolypropyleneEnd Caps PolypropyleneCenter Core PolypropyleneOuter Support Cage PolypropyleneO-RingsGaskets Buna EPDM
Silicone
SanitizationSterilizationFiltered Hot Water 80˚C for 30 minSteam Sterilization 121˚C for 30 min
multiple cycles
Chemicals Cartridges are chemically compatible with most chemicals and sanitizing agentsNote Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized
DimensionsLength10 to 40 inches (254 to 1016 cm) nominal Outside Diameter270 inches (70 cm) nominal
Maximum Recommended Operating ConditionsChange Out ΔP 35 PSITemperature 176˚F (80˚C)
FDA Listed MaterialsManufactured from materials which are listed for food contact applications in Title 21 of the US Code of Federal Regulations
ToxicityAll polypropylene components meet the specifications for biological safety per USP Class VI ndash 121˚C for plastics
Other Applications
OPP Rating (micro) A Length C End Cap Style O-RingsGaskets - Adders045 30rdquo (762 cm) 2 = DOE Flat Gasket B = Buna I = Stainless Steel Insert