Optical Media Explain the basics of fiber-optic cable. Describe how fibers can guide light for long distances. Describe multimode and single-mode fiber.

Optical Media

• Explain the basics of fiber-optic cable.

• Describe how fibers can guide light for long distances.

• Describe multimode and single-mode fiber.

• Describe how fiber is installed.

• Describe the type of connectors and equipment used with fiber-optic cable.

• Explain how fiber is tested to ensure that it will function properly.

• Discuss safety issues dealing with fiber-optics.

The electromagnetic spectrum

• The light used in optical fiber networks is one type of electromagnetic energy.

• When an electric charge moves back and forth, or accelerates, a type of energy called electromagnetic energy is produced.

• This energy in the form of waves can travel through a vacuum, the air, and through some materials like glass.

• An important property of any energy wave is the wavelength.

• Radio, microwaves, radar, visible light, x-rays are all types of electromagnetic energy.

The electromagnetic spectrum

• The wavelength of an electromagnetic wave is determined by how frequently the electric charge that generates the wave moves back and forth.

• If the charge moves back and forth slowly, the wavelength it generates is a long wavelength.

• Visualize the movement of the electric charge as like that of a stick in a pool of water.

• If the stick is moved back and forth slowly, it will generate ripples in the water with a long wavelength between the tops of the ripples.

• If the stick is moved back and forth more rapidly, the ripples will have a shorter wavelength.

The electromagnetic spectrum

The electromagnetic spectrum

• Wavelengths that are not visible to the human eye are used to transmit data over optical fiber.

• These wavelengths are slightly longer than red light and are called infrared light.

• Infrared light is used in TV remote controls.

• These wavelengths were selected because they travel through optical fiber better than other wavelengths.

Ray model of light

• When electromagnetic waves travel out from a source, they travel in straight lines. • These straight lines pointing out from the source are called rays.• Think of light rays as narrow beams of light like those produced by lasers. • In the vacuum of empty space, light travels continuously in a straight line at 300,000

kilometers per second. • However, light travels at different, slower speeds through other materials like air,

water, and glass. • When a light ray called the incident ray, crosses the boundary from one material to

another, some of the light energy in the ray will be reflected back. • That is why you can see yourself in window glass. • The light that is reflected back is called the reflected ray.

Ray model of light

• The light energy in the incident ray that is not reflected will enter the glass.

• refracted ray - The entering ray will be bent at an angle from its original path.

• How much the incident light ray is bent depends on the angle at which the incident ray strikes the surface of the glass and the different rates of speed at which light travels through the two substances

• The optical density of the glass determines how much the rays of light in the glass bends.

• Optical density refers to how much a light ray slows down when it passes through a substance.

• The greater the optical density of a material, the more it slows light down from its speed in a vacuum.

• The ratio of the speed of light in a material to the speed of light in a vacuum is called the Index of Refraction.

Reflection

• When a ray of light (the incident ray) strikes the shiny surface of a flat piece of glass, some of the light energy in the ray is reflected.

• The angle between the incident ray and a line perpendicular to the surface of the glass at the point where the incident ray strikes the glass is called the angle of incidence.

• The angle at which a light ray strikes a reflective surface determines the angle that the ray will reflect off the surface.

Interactive Media Activity

Refraction

• When a light strikes the interface between two transparent materials, the light divides into two parts.

• Part of the light ray is reflected back into the first substance, with the angle of reflection equaling the angle of incidence.

• The remaining energy in the light ray crosses the interface and enters into the second substance.

Refraction

• If the incident ray strikes the glass surface at an exact 90-degree angle, the ray goes straight into the glass.

• The ray is not bent. However, if the incident ray is not at an exact 90-degree angle to the surface, then the transmitted ray that enters the glass is bent.

• The bending of the entering ray is called refraction. • How much the ray is refracted depends on the index of refraction of the

two transparent materials. • Interactive Media Activity

Total internal reflection

• A light ray that is being turned on and off to send data (1s and 0s) into an optical fiber must stay inside the fiber until it reaches the far end.

• The ray must not refract into the material wrapped around the outside of the fiber.

• The refraction would cause the loss of part of the light energy of the ray.

• A design must be achieved for the fiber that will make the outside surface of the fiber act like a mirror to the light ray moving through the fiber.

• If any light ray that tries to move out through the side of the fiber were reflected back into the fiber at an angle that sends it towards the far end of the fiber, this would be a good “pipe” or “wave guide” for the light waves.

Total internal reflection

• The laws of reflection and refraction illustrate how to design a fiber that guides the light waves through the fiber with a minimum energy loss.

• The following two conditions must be met for the light rays in a fiber to be reflected back into the fiber without any loss due to refraction: – The core of the optical fiber has to have a larger index of refraction

(n) than the material that surrounds it. The material that surrounds the core of the fiber is called the cladding.

– The angle of incidence of the light ray is greater than the critical angle for the core and its cladding.

Total internal reflection

• Restricting the following two factors controls the angle of incidence: – The numerical aperture of the fiber – The numerical aperture of a

core is the range of angles of incident light rays entering the fiber that will be completely reflected.

– Modes – The paths which a light ray can follow when traveling down a fiber.

• By controlling both conditions, the fiber run will have total internal reflection. This gives a light wave guide that can be used for data communications.

Fiber Optic Cabling

• The core is the light transmission element at the center of the optical fiber. All the light signals travel through the core.

• Cladding is also made of silica but with a lower index of refraction than the core. Light rays traveling through the fiber core reflect off this core-to-cladding interface as they move through the fiber by total internal reflection.

• Surrounding the cladding is a buffer material that is usually plastic. The buffer material helps shield the core and cladding from damage.

• The strength material surrounds the buffer, preventing the fiber cable from being stretched when installers pull it. The material used is often Kevlar, the same material used to produce bulletproof vests.

• The outer jacket surrounds the cable to protect the fiber against abrasion, solvents, and other contaminants.

Fiber Optic Cabling

Higher bandwidth.

Fiber Optic Cabling

• If the diameter of the core of the fiber is large enough so that there are many paths that light can take through the fiber, the fiber is called “multimode” fiber.

• Single-mode fiber has a much smaller core that only allows light rays to travel along one mode inside the fiber.

Fiber Optic Cabling

• Every fiber-optic cable used for networking consists of two glass fibers encased in separate sheaths.

• One fiber carries transmitted data from device A to device B.

• The second fiber carries data from device B to device A.

• This provides a full-duplex communication link.

• Typically, these two fiber cables will be in a single outer jacket until they reach the point at which connectors are attached.

Fiber Optic Cabling

• Warning: The laser light used with single-mode has a longer wavelength than can be seen.

• The laser is so strong that it can seriously damage eyes. • Never look at the near end of a fiber that is connected to a device at the

far end. • Never look into the transmit port on a NIC, switch, or router. • Remember to keep protective covers over the ends of fiber and inserted

into the fiber-optic ports of switches and routers.

Core - Cladding

Transmitting Devices

• The transmitter converts the electronic signals into their equivalent light pulses.

• There are two types of light sources used to encode and transmit the data through the cable: – A light emitting diode (LED) producing infrared light. – Light amplification by stimulated emission radiation (LASER) a light

source producing a thin beam of intense infrared light usually with wavelengths of 1310nm or 1550 nm.

– Lasers are used with single-mode fiber over the longer distances involved in WANs or campus backbones.

Receiving Devices

• The receiver functions something like the photoelectric cell in a solar powered calculator.

• When light strikes the receiver, it produces electricity. • The semiconductor devices that are usually used as receivers with fiber-optic

links are called p-intrinsic-n diodes (PIN photodiodes). • When struck by a pulse of light at the proper wavelength, the PIN photodiode

quickly produces an electric current of the proper voltage for the network. • It instantly stops producing the voltage when no light strikes the PIN photodiode. • This generates the voltage changes that represent the data 1s and 0s on a

copper cable.

ST and SC Connectors

• The type of connector most commonly used with multimode fiber is the Subscriber Connector (SC connector).

• On single-mode fiber, the Straight Tip (ST) connector is frequently used.

Fiber Optic Patch Panel

Fiber Optic Patch Panel

• Fiber patch panels similar to the patch panels used with copper cable.

• These panels increase the flexibility of an optical network by allowing quick changes to the connection of devices like switches or routers with various available fiber runs, or cable links.

Signals and noise in optical fibers

• Fiber-optic cable is not affected by the sources of external noise that cause problems on copper media because external light cannot enter the fiber except at the transmitter end.

• Although fiber is the best of all the transmission media at carrying large amounts of data over long distances, fiber is not without problems. When light travels through fiber, some of the light energy is lost.

• The most important factor is scattering. – The scattering of light in a fiber is caused by microscopic non-

uniformity (distortions) in the fiber that reflects and scatters some of the light energy.

Signals and noise in optical fibers

• Absorption is another cause of light energy loss. – When a light ray strikes some types of chemical impurities in a

fiber, the impurities absorb part of the energy. – This light energy is converted to a small amount of heat energy. – Absorption makes the light signal a little dimmer.

• Another factor that causes attenuation of the light signal is manufacturing irregularities or roughness in the core-to-cladding boundary. – Any microscopic imperfections in the thickness or symmetry of the

fiber will cut down on total internal reflection and the cladding will absorb some light energy.

Signals and noise in optical fibers

• Dispersion of a light flash also limits transmission distances on a fiber. – Dispersion is the technical term for the spreading of pulses of light

as they travel down the fiber

Installation, care, and testing of optical fiber

• Once the fiber-optic cable and connectors have been installed, the connectors and the ends of the fibers must be kept spotlessly clean.

• The ends of the fibers should be covered with protective covers to prevent damage to the fiber ends.

• When these covers are removed prior to connecting the fiber to a port on a switch or a router, the fiber ends must be cleaned.

• Clean the fiber ends with lint free lens tissue moistened with pure isopropyl alcohol.

• The fiber ports on a switch or router should also be kept covered when not in use and cleaned with lens tissue and isopropyl alcohol before a connection is made.

• Dirty ends on a fiber will cause a big drop in the amount of light that reaches the receiver.

Installation, care, and testing of optical fiber

• When a fiber-optic link is being planned, the amount of signal power loss that can be tolerated must be calculated.

• This is referred to as the optical link loss budget.

• The decibel (dB) is the unit used to measure the amount of power loss. – It tells what percent of the power that leaves the

transmitter actually enters the receiver.

• Testing fiber links is extremely important and records of the results of these tests must be kept.

• Two of the most important instruments are – Optical Loss Meters – Optical Time Domain Reflectometers (OTDRs).