Operator's Manual 1 HP (Maximum Developed) 12 Speeds (250-3100 R.P.M.) 5/8 Inch Chuck 15-INCH DRILL PRESS Model No, 137.229151 CAUTION: Before using this Drill Press, read this manual and follow all its Safety Rules and Operating Instructions • Safety Instructions • Installation • Operation • Maintenance • Parts List • EspaSol Customer Help Line 1-800-843-1682 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit our Craftsman website: www.sears.comlcraftsman Part No. 137229151001
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Operator's Manual
1 HP (Maximum Developed)12 Speeds (250-3100 R.P.M.)5/8 Inch Chuck
15-INCH DRILL PRESSModel No,137.229151
CAUTION:Before using this Drill Press,read this manual and follow
all its Safety Rules andOperating Instructions
• Safety Instructions• Installation
• Operation• Maintenance• Parts List
• EspaSol
Customer Help Line1-800-843-1682
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USAVisit our Craftsman website: www.sears.comlcraftsman
FULL ONE YEAR WARRANTYIf this Driss Press fails due to a defect in material or workmanship within one year of date of purchase,Sears will at its option repair or replace it free of charge.
Return this Drill Press to a Sears Service Center for repair, or to place of purchase for replacement.
This warranty gives you specific legal rights, and you may also have other rights which may vary fromstate to state.
Sears, Roebuck and Co., Dept. 817 WA, Hoffrnan Estates, IL 60179
_q
Some dust created by power sanding, sawing, grinding, drilling and other construction activities containschemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Someexamples of these chemicals are:
• Lead from lead-based paints• Crystalline silica from bricks, cement and other masonry products• Arsenic and chromium from chemicallytreatsd lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce )/ourexposure to these chemicals work in a well-ventnated area and work with approved safety equipmentsuch asdust masks that are spec a y des gned to filter out microscopic particles.
To avoid electrical hazards, fire hazards, or damage tothe tool, use proper circuit protection.
Your drill press is wired at the factory for 120V operation.Connect to a 120V, 15 AMP branch circuit and use a 15AMP time delay fuse or circuit breaker. To avoid shock orfire, replace power cord immediately if it is worn, cut ordamaged in any way.
2
GENERAL SAFETY INSTRUCTIONS 14.BEFORE USING THE DRILL PRESS
Safety is a combination of common sense, staying alertand knowing how to use your ddll press. 15.
REMOVE ADJUSTING KEYS AND WRENCHES.Form the habit of checking to see that keys andadjusting wrenches are removed from the tool beforeturning =ON".
NEVER LEAVETOOL RUNNING UNATFENDED.TURN THE POWER "OFF". Don't leave the tool untilit comes to a complete stop.
To avoid mistakes that could cause sedous injury, do not 16. NEVER STAND ON TOOL Sedous injurycould occurplug the drill press in until you have read and understood if the tool is Upped or ifthe cuffingtool is unintentionallythe following: contacted.
1. READ and become familiar with this entire instructionmanual.LEARN the tool's applications,limitstJons,andpossiblehazards.
2. KEEP GUARDS IN PLACE and in working order.
3. DON'T USE IN A DANGEROUS ENVIRONMENT.Don't use power tools in damp or wet locations, orexpose them to rain. Keep work area well lighted.
4. DO NOT use power tools in the presence of flammableliquidsor gases.
5. KEEP WORK AREA CLEAN. Cluttered areas andbenches inviteaccidents.
6. KEEP CHILDREN AWAY.AUvisitorsshould be kept ata safe distance from the work area.
7. DON'T FORCE THE TOOL. It Willdo the job betterand safer at the rate for which it was designed.
8. USETHE RIGHTTOOL. Don't force tool or theattachment to do a job for which it was not designed.
. WEAR PROPER APPAREL DO NOT wear looseclothing, gloves, neckties, rings, bracelets, or other_lowelrywhich may get caught in moving parts.
onslip footwear is recommended. Wear protectivehair covering to contain long hair.
10. WEAR A FACE MASK OR DUST MASK.Drillingoperation produces dust.
11. DISCONNECTTOOLS before servicing, and whenchanging accessories, such as blades, bits, ct_ttem,and the like.
12. REDUCETHE RISK OF UNINTENTIONAL STARTING.Make sure the switch is in "OFF" position beforeplugging in.
13. USE RECOMMENDED ACCESSORIES. Consult theowner's manual for the recommended accessories.The use of improper accessories may cause risk ofinjury to persons.
17. DON'T OVERREACH. Keep proper footing andbalance at all times.
18. MAINTAIN TOOLS WITH CARE. Keep tools sharpand clean for best and safest performance. Followinstructionsfor lubricating and changing accessories,
19. CHECK FOR DAMAGED PARrs. Beforefurther use ofthe tool,a guard or other pert that is damaged shouldbe carefully checked to determine that it will operateproperty and perform its intended function.Check foralignment of movingparts, binding of moving parts,breakage of parts, mounting,and any other conditionsthat may affect its operation.A guard or other part thatis damaged should be properly repaired or replaced.
20. MAKE WORKSHOP laD PROOF withpadlocks,masterswitches, or by removing starter keys.
21.
22.
DO NOT operate the tool if you are underthe influenceof any drugs, alcohol or medication that could affectyour abilityto use the tool properly.
Dust generated from certain materials can behazardous to your health. Always operate the drillpress in a well-ventilated area and provide for properdust removal. Use dust coflection systems wheneverpossible.
23. ALWAYS WEAR EYEPROTECTION. Any ddll presscan throw foreign objects intothe eyes which could causepermanent eye damage.ALWAYSwear Safety Goggles(not glasses) that comply with
ANSI safety standard Z87.1. Everyday eyeglasseshave only impact-resistant lenses. They ARE NOTsafety glasses. Safety Goggles are available at Seam.NOTE: Glasses or goggles not in compliance withANSI Z87.1 could seriouslyhurt you when they break.
SAVE THESE INSTRUCTIONS
3
SPECIFIC SAFETY INSTRUCTIONSFOR THE DRILL PRESS
14.SECURE WORK. Usa clamps or vise to holdthework when practical. It's safer than using your handand it frees both hands to operate tool,
For your ownsafety, do nottry to use yourdrill press orplug it in untilit is completelyassembled and installedaccordingto the instructions,and untilyou have readand understoodthis instrucbonmanual:
15.WHEN usinga drill pressvise, always fasten to thetable.
16.MAKE SURE allclamps and locksare firmlytightened before drilling.
1. YOUR DRILL PRESS MUST BE BOLTED securelyto a workbench. In addition, if there is any tendencyfor your drillpressto move duringcertain operations,boltthe workbenchto the floor.
2. THIS DRILL PRESS is intended for usa indryconditions,indooruse only.
3. WEAR EYE PROTECTION. USE face or dustmaskalongwithsafety goggles if drillingoperation is dusty.USE ear protectors,especially duringextendedperiodsof operation.
4. DO NOT wear gloves, neckties, or looseclothing
5. DO NOT try to drillmaterial too small to be securelyheld.
6. ALWAYS keep hands out of the path of a drill bit.Avoidawkward hand positionswhere a sudden slipcouldcause your hand to move into the drill bit.
7. DO NOT installor use any drill bit that exceeds 175mm (7") in lengthor extends 150 mm (6") belowthechuckjaws. They can suddenly bend outwardorbreak.
8. DO NOT USE wire wheels, router bits, shaper cutters,circle(fly) cutters,or rotary planerson thisdrill press.
17.SECURELY LOCK THE HEAD and table supper tothe column, and the table to the table supportbeforeoperatingthe drillpress.
18.NEVER turn your drill presson before clearing thetable of allobjects (tools,scrapsof wood, etc.)
19.BEFORE STARTING the operation,jog the motorswitchto make sure the drill bitdoes notwobbleorvibrate.
20.LET THE SPINDLE REACH FULL SPEED beforestartingto drill. If your drillpress makes an unfamiliarnoise or if it vibrates excessively,stop immediately,turn the drillpress off and unplug. Do not restartuntilthe problem is corrected.
21.DO NOT perform layoutassembly or set up work onthe tablewhile the drill press is in operation.
22.USE RECOMMENDED SPEED for drill accessoryand workpiecematerial. SEE INSTRUCTIONS thatcome withthe accessory
23.WHEN DRILLING large diameter holes,clamp theworkpiece firmlyto the table. Otherwise, the bitmaygrap and spin the workpieceat high speed. DO NOTUSE fly cuttersor multiple-parf hole cutters,as theycan come apart or become unbalancedin use.
9. WHEN cuttinga large piece of material make sure itis fully supportedat the table height.
24.MAKE SURE the spindle has come to a completestop before touching the workpiece.
10.DO NOT perform any operation freehand. ALWAYSholdthe workpiece firmly against the table so it willnotreck or twist. Use clamps or a vise for unstableworkpiece.
11.MAKE SURE there are no nailsor foreign objects inthe partof the workpieceto be drilled.
12.CLAMP WORKPIECE OR BRACE against the leftside of the columnto prevent rotation. If it is too shortor the table is tilted, clamp solidlyto the table and usethe fence provided.
25.TO AVOID INJURY from accidental starting,alwaysturn the switch"OFF" and unplugthe drill pressbefore installingor removing any accessoryorattachmentor making any adjustment
26.KEEP GUARDS IN PLACE and inworkingorder.
27.USE ONLY SELF-EJECTING TYPE CHUCK KEY asprovidedwiththe drill press
13.IF THE WORKPIECE overhangs the table such thatit will fall or tip if not held, clamp it to the table orprovide auxiliary support.
SAVE THESEINSTRUCTIONS
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION ORBREAKDOWN, groundingprovidesa path of leastresistancefor electric currentand reduces the riskofshock. This tool is equipped withan electric cordthathas an equipmentgroundingconductorand groundingplug.The plugMUST be pluggedintoa matchingreceptacle that is properlyinstalledand grounded inaccordancewithALL local codesand ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will notfit
the receptacle,have the proper receptacle installedby aqualifiedelectdcian.
This tool is intendedfor use on a circuitthat has areceptacle like the one illustratedin'FIGURE A.FIGURE A shows a 3-prongelectricalplug andreceptacle that has a groundingconductor.If a pmparlygroundedreceptacle is notavailable, an adaPter(FIGURE B) can be usedto temporarilyconnectthisplugto a 2-contact ungroundedreceptacle.The adapter(FIGURE B) has a rigid lug extendingfrom it that MUSTbe connectedto a permanent earth ground,such as aproperlygrounded receptacle box. THE TEMPORARYADAPTER SHOULD BE USED ONLY UNTIL APROPER GROUNDED OUTLET CAN BE INSTALLEDBY A QUALIFIED ELECTRICIAN. The CanadianElectricalCode prohibitsthe use of adapters.
IMPROPER CONNECTION of the equipment groundingconductorcan result inrisk of electricshock. Theconductorwiththe green insulation(withor withoutyellow stripes)is the equipment groundingconductor.Ifrepair or replacementof the electriccord or plug isnecessary, DO NOT connectthe equipment groundingconductorto a liveterminal.
CHECK with a qualified electrician orservice personnelif you do notcompletelyunderstandthe groundinginstructions,or if you are notsure the tool is properlygrounded.
USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE
3oPRONG GROUNDING PLUGS AND 3-POLERECEPTACLE THAT ACCEPT THE TOOL'S PLUG.
REPAIR OR REPLACE DAMAGED OR WORN CORDIMMEDIATELY.
CAUTION: In all cases, make certain the receptacle inquestionis properlygrounded. If you are notsure have acertifiedelectriciancheck the receptacle.
This drill press is for indoor use only. Do not expose torain or use in damp locations.
Flg. A3-Prong Plug
_" p.rGprroP_o°nl_;_o_nrin;e
GUIDELINES FOR EXTENSION CORDS Fig. BGroundingLug
Make sure yourextension cord is ingood condition.When usingan extensioncord, be sure to use one heavyenoughto carrythe current your productwill draw. Anundersizedcord will cause a dropin line voltageresultingin lossof power and overheating. The tablebelowshowsthe correct size to use accordingto cordlength and nameplate ampere rating. If in doubt, use thenext heavier gauge. The smallerthe gauge number, theheavier the cord.
Adapter
is Connected to aKnown Ground
Be sure your extension cord is properly wired and ingoodcondition.Always replace a damaged extensioncordor have it repaired by a qualifiedperson beforeusingit. Protectyour extensioncords from sharp objects,excessive heat and damp or wet areas rdI_ hV_lll_ [e_-*ll[el na al] :s :1,:(ii :1_K'I[el _ [l(e] _| i},.llr:t tjLt/t.
Use a separate electrical circuit for your tools. Thiscircuit must not be less than #12 wire and should be
protected with a 15 Amp time lag fuse. Beforeconnecting the motor to the power line, make sure theswitch is in the OFF position and the electric current is
rated the same as the current stamped on the motornameplate. Running at a lower voltage will damage themotor.
This tool must be grounded while in use to protect theoperator from electrical.
(When usinc
6,mpere Ratingmore than not more than
0 66 10
10 12
12 16
SAVE THESE INSTRUCTIONS
120 volts only)
Total length of cord in feet25' 50' 100' 150'
18 16 16 14
18 16 14 12
16 16 14 12
14 12 Not recommended
RECOMMENDED ACCESSORIES UNPACKING AND CHECKING CONTENTS
r_r/_J=-KqKE=]
Use onlyaccessorier recommended for this drillpress.Followinstructionsthat accompany accessories.Use ofimproperaccessoriesmay cause hazards.
Visityour Sears Hardware Department or see theCraftsman Power and Hand Tools Catalog for thefollowing accessories:
• Drill bits• Hold-Down and Guide• DrillpressVises• Clamping kit
If any part is missingor damaged, do not plugthe drillpressin untilthe missingor damaged part is replaced,and assemblyis complete.
Carefully unpack the drill press and all its parts, andcompare againstthe list below.
To protectthe drillpress from moisture,a protectivecoatinghas been applied to the machinedsurfaces.Remove thiscoating with a soft clothmoistenedwithkerosene or WD-40.
.r_rArl,_1d _11_[e
Use only accessoriesdesigned for this drill press to avoidinjuryfrom thrownbrokenparts or workpieces.
Sears may recommend other accessories not listed inthis manual. See your nearest Sears store or Power andHand Tool Catalog for other accessories.
Do not use may accessoryunless you have completelyreadthe instruction or operator's manual for thataccessory.
To avoidfire or toxic reaction, never use gasoline,naphtha, acetone, lacquerthinner or similarhighlyvolatilesolventsto clean the drill press.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION QUANTITYA. Head assembly tB. Table 1C. Base 1D. Column assembly 1
BASE - Supportsdrill press. For additionalstability,holesare providedin base to bolt drillpressto floor.(See "Specific Safety Instruction for Drill Presses.")
BACKUP MATERIAL - Apiece of scrapwood placedbetweenthe workpieceand table. The backup beardpreventswood in the workpiece from splintedngwhenthe drillpasses throughthe backsideof the workpiece. Italsoprevents drillingintothe table top.
BELT GUARD ASSEMBLY - Covers the pulleysandbeltduringoperationof the drillpress.
BELT TENSION - Refer to the "Assembly" Section,"Installingand Tensioning Belt.".
BELT TENSION HANDLE - Turn the handle clockwiseto apply tensionto belt, turnthe handle counterclockwiseto release belt tension.
BELT TENSION LOCK KNOBS - Tighteningthe knobslocksthe motor bracket supportand the belt tensionhandle, maintainingcorrect beltdistance and tension.
BEVEL SCALE - Shows degree of table tilt for beveloperaions. The scale is mounted on the side of the arm.
CHUCK - Holdsdrill bit or other recommendedaccessoryto performdesired operations.
CHUCK KEY - A self-ejectingchuckkey whichwill popoutof the chuckwhen you let go of it.This actionisdesignedto help preventthrowingof the chuck key fromthe chuckwhen the peer is turned ON. Do not use anyother key as a substitute; ordera new one if hamaged orlost.
COLUMN - Connects the head, table, and base on aone piece tube for easy alignment and movement.
COLUMN COLLAR - Holds the rack to the column.Rack remains movable in the collar to permit tablesupport movements.
COLUMN SUPPORT - Supports the column, guides therack and providesmountingholes for column to base.
DEPTH SCALE STOP NUTS - Lock the spindle to theselected depth.
DEPTH SCALE - Indicates depth of hole being drilled.
DRILL BIT - The cutting tool used in the drill press tomake holes in a workpiece.
DRILL ON/OFF SWITCH - Has lockingfeature. Thisfeature is intended to help prevent unauthorizedandpossible hazardous use by children and others. Insertthe key into the switch to turn the drill press on.
DRILLING SPEED - Changed by placingthe belt in anyof the steps (grooves) inthe pulleys.See the SpindleSpeed Chart insidebeltguard.
FEED HANDLE - Moves the chuckup or down. IFnecessary, one or two of the handles may be removedwhenever the workpiece is of suchunusualshape that itinterfereswith the handles.
FENCE - Attaches to the table to alignthe workpieceorfor fast repetitivedrilling.Removable. Remove fencewhen it interfereswith other drillpress accessories.
HEAD LOCKS - Locks the head to the column.ALWAYS lockthe head in placewhile operatingthe drillpress.
RACK - Combines withgear mechanism to provideeasy elevationof the table by the hand operated tablecrank.
REVOLUTION PER MINUTE (R.P.M.)- The numberofturns completedby a spinningobject in one minute.
SPINDLE SPEED - The RPM. of the spindle.
SPRING CAP - Adjusts quill spring tension.
TABLE SUPPORTS LOCK - Tighteninglocksthe tablesupportto column. Always have it lockedin placewhileoperatingthe dirll press.
TABLE - Provides a working surface to supporttheworkpiece.
TABLE ARM - Extends beyond the table supportformounting and aligning the table.
TABEL BEVEL LOCK - Locks the table in any positionfrom 0° - 45°
TABLE CRANK - Elevates and lowers the table. Turnclockwise to elevate the table. Support lock must bereleased before operating the crank.
TABLE LOCK - Locks the table after it is rotated tovariouspositions.
TABLE SUPPORT - Rides on the column to supportthetable arm and table.
THREADED DRAIN (518")- Attach a 5/8" (pipethreaded) metal pipe to the threaded opening fordrainingexcees oil into container.For a non-drainingsurfaceattach a threaded metal plug.Pipe and plugnot .included.
The DdlTPress is very heavy and MUST be liftedwiththehelpof 2 PEOPLE OR MORE, to safetyassembly it.
COLUMN SUPPORT TO BASE (FIG. A)
1. Position the base (1) on the floor.2. Place the column (2) on the base, aligning the
holes in the column support with the holes in thebase.
3. Locate the four long hex bolts (3) from the looseparts bag.
4. Place a bolt in each hole through the column
support and the base. Tighten with an adjustablewrench.
i
INSTALLING THE TABLE (FIG. B and C)1. Locate the table crank (1) and support lock (2) from
the loose parts bag.2. Insert the support lock handle into the hole (3) at
the rear of the table support assembly. Tighten byhand.
3. InstaJIthe table crank handle (3) onto the smallshaft (4), aligning the set screw (5) with the flatsurface of the shaft (4), aligning the set screw (5)with the fiat surface of the shaft. Tighten the setscrew with a hex wrench.
10
Rg. B
4. (FIG. C) Loosen the support lock (2). Raise thetable arm assembly by turning the crank handle (1)clockwise. Tighten the support lock.
5. Place the table (6) in the table arm assembly.Tighten the table lock handle (7).
Rg. C
INSTALLING EXTENSION WING
1. Place the handle (OWVG) onto the upper tube(OWVH).
2. Place the flat washers (OT6T) onto the hex headbolts (OJUB). Insert the bolt (OJUB) into the uppertube (OWVH), and tighten.
3. Insert the hes head bolts (OJUB) onto the uppertube (OJUB) and tighten.
4. Place the upper tube assembly under the table.5. Place the set plate (OWVJ) onto the clamp bolt
(OWVK). Insert the set plate assembly into thetable and tighten.
NOTE: If length adjustment is necessary, loosen
the clamp bolt (OWVK) to the desired length andtighten the clamp bolt.
OWVE
INSTALLING THE HF.AD (FIG. D)
mvl/_d_ql K_
The Drill Press h_d Is very heavy and MUST be liftedwith the help of 2 PEOPLE OR MORE,to safelyassemble the Drill Press head on the column.
1. Carefully lift the head (1) above the column (2) andslide it onto the column.Make sure the head slldeadown over the column as far as poealble.Algn thehead with the base.
2. Using the hex wrench, tighten the two head lock eatscrews (3) on the right side of the head.
Fig. D
"ry
J_3
INSTALLING FEES HANDLES (FIG. E)
1. Locate three feed handles in the loose parts bag.2, Screw the feed handles (1) into the threaded holes (2)
in the hub (3), Tighten
FENCE ASSEMBLY (FIG. F)This drill press has a channeled table top.
1. Determine the desired location for the fence (1).SlldetheT-blocks (2) Into the appropriate channels asshown
2. Align the mounting holes of the fence over theT-block'sthreaded hloes.
3. Place a washer (3) on the threaded end of the knob (4).Insert the knob through the mounting hole of the fenceinto the T-block,and Ugbetan.
4. Repeatfor the other knob andT-block.
Fig. F
11
INSTALUNG THE CHUCK (FIG. G, H, and I1. Clean out the tapered hole In the chuck (1) wltha
CkHlndoth.2. Clean tapered surfacason the arbor(2) and spindle(3).
CAUTION: Make sure there am no foreign particlesstk:kingto the surfaces.The slightestpiece of dirt onany of these surfaces will prevent the chuck fromseating properly.This will cause the ddll chuck andbit to wobble. If tapered hole is extremely dirty, use acleaning solvent.
Fig. G
7. Using a robber mallet, plastic-tipped hammer, or amOCKOTwood and a hammer, firmlytap the chuckupward into posi_n on the spindle shaft.
Fig. I
3. 4(FIG. H) Push the chuck(1) onto the spindlearbor (2). Tap gently to ensure seat.
4. 5Lower the spindle by turning the feed handles (8)countemlockwise, until the slot (4) appears on thequill (5).
5. Push the chuck and spindlearborup into the spindle,making sure the tang (6) (upper narrow end of thespindle arbor shank) is engaged and locked in theinner slot (7) of the spindle.This can be seenthroughthe outer slot (4) of the quill by rotatingthechuck and arbor until the two slotsare aligned.
6. Open the jaws of the chuck (1) by rotating the chucksleeve clockwise.To prevent damage, make sure thejaws are completely receded into the chuck.
CAUTION: All the adjustments for the opera,on of theddl press have been completed at the lectory.Due tonormalwear and use, some occasional madjustmentemay be necessary.
NOTE: The table arm and support has a preddlledholewitha lockingset screw insertedfor lockingthe table toa predetermined0° horizontal_. It must be loosenedto change the angle of the table.
1. Insert a 1/4", or larger diameter,precisiongroundstsetrod (1), approximately3" long,intothechuck(2).Tighten the chuckjaws.
2. Raise table to working heightand lock.3. Using the combinationsquare (3), placeena edge
fiat on the tebie, and alignthe other edge verlfoallybeside the rod (1).
Fig. K
Fig. L
5
6
47
BEVEL SCALE (FIG. L and M)
NOTE: The bevel scale has been included to measureapproximate bevel angles. If precision is necessary,a square or other measuring tool should he used topositionthe table.To use the bevel scale (7):1. Loosenthe Ioddngset screw (4) to RELEASE it from
the table support.2. Loosen the large hex head bevel locking bolt (6).
2
1
3
I I I I I I I I I I I I
[4. If an adjustment is necessary, loosen the lockingset
screw (4) with the 3 mm hex key to RELEASE thetable from the horizontal position.
5. Loosen the large hex head bevel lockingbolt (6).
Tolprevent injury,be sure to hold the table &table armassembly, so it will not swivelor tilt.
6. Align the square to the red by rotating the table untilthe square and rod are in line.
7. Retighten the large bex belt. (6).
To prevent injury,be sure to holdthe table & table armassembly, so it will not swivel or tilt.
3. Tilt the table, aligningthe desired angle measurementto the zero line opposite the scale (7).
4. Tighten the bevel lockingbolt. (6).5. To returnthe table to its original position, loosen the
6. Tighten the locking set screw (4) until it is seated inthe horizontal 0_hole of the table support.
Fig. M
5
6
7
13
_[wr_,1 =t_'llKl[e_
To prevent personal injury,always disconnect plugfrom the power source when making any adjustment.
SPINDLE I QUILL (FIG. N)Rotate the feed handles counterclockwiseto lowerspindleto its lowestposition. Hand supportthespindlesecurely and move it back and forth aroundthe axis. If there is too much play, do the following:1. Loosenthe lock nut(1).2. Turn the screw (2) clockwiseto eliminate the play,
butwithoutobstructingthe upward movement ofthe spindle. (A little play in the spindle is normal.)
3. Tighten the lock nut(1).
Fig. O
Fig. N
QUILL RETURN SPRING (FIG. O)The quill returnspring may need adjustment ifthetensioncause the quillto returntoo rapidly or tooslowly.1. Lowerthe table for additionalclearance.2. Place a screwdriver in the lower front notch (1) of
the springcap (2). Hold it in place while looseningand removingonly the outer jam nut (3).
3. With the screwdriverstillengaged inthe notch,loosenthe inner nut(4) just until the notch(5)disengages from the boss (6) on the drill presshead.
CAUTION: DO NOT REMOVE THIS INNER NUT,because the springwill forcibly unwind.
4. Carefully turn the spring cap (2) counterclockwisewith the screwdriver, engaging the next notch.
5. Lower the quill to the lowest position by rotating thefeed handle in a counterclockwise direction whileholding the spring cap (2) in position.
6. If the quill moves up and down as easily as youdesire, tighten the standard nut (4) with theadjustable wrench. If too loose, repeat steps 2through 5 to tighten. If too tight, reverse steps 4 and5.DO NOT OVERTIGHTEN and restrict quillmovement.
7. Replace the jam nut (3) and tighten against thestandard nut (4) to prevent the standard nut fromreversing.
2
To avoid injury from an accidental start, ALWAYSmake sure the switch is in the "OFF" position, theswitch key is removed, and the plug is not connectedto the power source outlet before making beltadjustments.
BELT TENSION (FIG. P)Make sure pulleysare aligned properly as shown inFigure R on page 15.1. To unlockthe belt tension, turn the belt tensionlock
knobs (1) on each side of the drill pressheadcounterclockwise.
2. Tighten the belts by turningthe belt tension handle(2) clockwise.
3. Loosenthe beltsby turning the belt tensin handle(2) counterclockwise.Set belts on pulleysteps fordesired speed.
4. Lock the belt tensionlockknobs (1) by turningclockwise.
NOTE: Belt tension is correct if the belt deflectsapproximately 1/2 inch when pressed at its center.
Fig. P
14
_vlvh_ =1_[ITo avoid injury from an accidental start, ALWAYSmake sure the switch is in the "OFF" position, theswitch key is removed, and the plug is not connectedto the power source outlet before making beltadjustments.
ALIGNING THE BELT PULLEYS (FIG. N)Open the head cover of the Drill Press. Checkalignment of the pulleys with a straight edge (5) suchas a framimg square, a level, or a piece of a wood.Lay the straight edge across the top of the pulleys. Ifall three pulleys are NOT aligned:1. Release belt pressure by loosening the belt tension
lock knobs (4) on either side of the head, unlockingthe belt tension handle (1).
2. Loosen the motor mount nuts (2). Lift or lower themotor (3) until the pulleys are in line.
3. Tighten the motor mount nuts (2) using anadjustable wrench.
NOTE: To avoid rattles or other noise, the motorhousing should not touch the lower belt guardhousing.
4. Retighten the belts by turning the belt tensionhandle (1) clockwise, until the belt deflectsapproximately 1/2 inch when pressed in the center.
NOTE: Refer to the chart inside the belt guardcover for recommended drilling speeds andbelt/pulley positions.
5. Lock the belt tension lock knobs (4) by turningclockwise.
NOTE: When the belts are new, it may be difficult tomove the belts. As the machine is used, the belts willgain more elasticity and will be easier to adjust.
Fig. Q
BASIC DRILL PRESS OPEATIONS
SPEEDS AND BELT PLACEMENT (FIG. R)
This drill press has 12 speeds, as listed below:250 RPM 600 RPM 1620RPM340 RPM 650 RPM 1900RPM390 RPM 990 RPM 2620 RPM510 RPM 1550 RPM 3100RPM
See inside of the pulley guard for specific placementof the belts on the pulleys to change speeds.
To avoid possible injury, keep guard closed, in place,and in proper working order while tool is in operation.
Fig. R
9250 trim_
o510 tdmin
i
9
9
9
9
9
9
Q
9
93100 tr_lin
1 4 3
15
ON I OFF SWITCH PANEL (FIG. S)The "ON I OFF" switchhas a removable, yellowplastickey. With the key removed from the switch,unauthorizedand hazardous use by childrenandother is minimized.1. To turnthe drillpress "ON', insert key (1) into the
slotof the switch(2), aqd move the switchupwardto the "ON" position
2. To turn the drill press"OFF', move the switchdownward.
3. To lockthe switchinthe =OFF" position, grasp theend, or yellow part, of the switchtoggle, and pull itout.
4. With the switchkey removed, the switchwill notoperate.
5. If the switchkey is removed while the drillpress isrunning,it can be turned "OFF" butcannot berestartedwithout insertingthe switchkey.
6. To turnthe worklight"ON", pressthe rocker switch(3).
7. Never leave the drill pressunattended. Turn thelightswitchand power switch"OFF" and wait until itcomesto a complete stop.
Rg. Sf
m
_3
--2
BI
ALWAYS lock the switch "OFF" when the drill press isnot in use. Remove the key and keep it in a safe place.In the event of a power failure, blown fuse, or trippedcircuit breaker, turn the switch "OFF" and remove thekey, preventing an accidental startup when power comeson.
INSTALLING DRILL BIT IN CHUCK (FIG. T)1. With the switch"OFF" and the yellow switchkey
removed, open the chuckjaws (1) usingthe chuckkey(2). Turn the chuck key counterclockwiseto open thechuckjaws (1).
2. Insertthe drillbit (3) into the chuck far enoughtoobtainmaximum grippingby the jaws, butnot farenough to touch the spiralgrooves(flutes) of the drillbitwhenthe jaws are tightened.
3. Make surethat the drillis centered in the chuck.4. Turn the chuckkey clockwiseto tightenthe jaws.
To avoid injury or accident by the chuckkey ejectingforcibly from the chuck when the power is turned "ON",use only the self-ejecting chuck key supplied with thisdrill press. ALWAYS recheck and remove the chuck keybefore turning the power"ON".
Fig.T
To preventthe workpieceor backup materialfrom beingtom from your hands while drilling, you MUST positionthe workpiece against the LEFT side of the column. If theworkpiece or the backup material is not long enough toreach the column, clamp them to the table, or use thefence provided with the drill press to brace the workpiece.Failure to secure the workpiece could result in personalinjury.
USING THE FENCE (FIG. U)The fence provides a way of accuratelyand quicklysettingup the workpiece for more precisionor for repitivedrillingoperations.1. Usingthe centerpunchor sharp nail, make an
indentationin the workpiecewhere _ou want to drill.2. Lowerthe drillbit to alignwith the indentationon the
workpiece. See "HOLDING A DRILLING LOCATION"page 19.
3. Loosenthe knobs (1) and slide the fence back stop (2)firmly against the longside of the workpiece.Tightenthe knobswhen inposition.
4_ Loosenthe wing nut (3) and slide the end stop(4)alongthe fence until it is firmly against the left sideofthe workpiece.Tighten the wing nut.
5. Check the accuracyby drillinga scrapworkpiece.Adjust if needed.
6. Holdwithyour hand or clamp the top surface of theworkpiece firmly to prevent it from liftingoff the tablewhen the bit is raised.
Fig. U
234
16
DRILLING TO A SPECIFIC DEPTH (FIG. V)Drillinga blindhole (not all the way throughworkpiece)to a given depth can be done two ways:
Workpleca method1. Mark the depth (1) of the hole on the side of the
workpiece.2. W'_ththe switch"OFF", bringthe drill bitdown until
the tip is even with the mark.3. Hold the feed handle (2) at thisposition.4. Spin the lower nut (3) down to contactthe depth
stop(4) on the head.5. Spin the upper nut(5) down and tightenagainst the
lower nut (3)..6. The drillbitwill nowstopafter travelingthe distance
marked on the workpiece.
Depth scale method
Note: With the chuckup the tipof'the drillbit must bejust slightlyabove the top of the workpiece.
1. With the switch "OFF", turn the feed handle (2) untildepth stop (4) points to the desired depth on thedepth scale (6) and hold the feed handle in thatposition.
2. Spin the lower nut (3) down to contact the depthstop (4).
3. Spin the upper nut (5) against the lower stop nut (3)and tighten.
4. The drill bit will stop after traveling the distanceselected on the depth scale.
Fig. V
LOCKING THE CHUCK AT THE DESIRED DEPTH(FIG. W)1. With the switch"OFF", turn the feed handlesuntil the
chuck (1) is at the desireddepth_Hold the feedhandlesat this position.
2. Turn the stopnut (2), located underthe depth stop(3), counterclockwiseand upwards,until it is againstthe depth stop.
3. The chuckwill now be held at this positionwhen thefeed handlesare released.
Flg.W
REMOVING CHUCK AND ARBOR (FIG. X)1. With the switch "OFF", adjust the depth stopnut(1) to
holdthe drillat a depth of three inches. (Seeinstructionsfor "LOCKING CHUCK AT DESIREDDEPTH").
2. Align the key holes inthe spindle (2) and quill(3) byrotatingthe chuckby hand.
3. Insertthe key wedge (4) into the key holes (2 & 3).4. Tap the key wedge (4) lightlywith a plastictipped
hammer, until the chuckand arbor fall out of thespindle.
NOTE: Place one hand below the chuck to catch itwhen it falls out.
Fig. X
S4
17
BASIC OPERATION INSTRUCTIONS
To get the best results and minimize the likelihoodofpersonalinjury,follow these instructionsfor operatingyour drillpress.
For your ownsafety, always observe the SAFETYINSTRUCTIONS listedhere and on pages 3, 4 and 5of the instructionmanual.
YOUR PROTECTION
To avoid being pulled intothe power tool,do notwearlooseclothing,gloves,neckties, or jewelry. Always tieback longhair.
1. If any part of your drill press is missing, malfunctioning,damaged or broken, stopoperation immediatelyuntilthat part is properlyrepaired or replaced.
2. Never placeyour fingers in a positionwhere theycouldcontactthe drill bitor other cuttingtool. Theworkpiecemay unexpectedly shift,or your hand couldslip.
3. To avoid injuryfrom partsthrownby the spring, followinstructionsexactly when adjustingthe springtensionof the quill.
4. To preven the workpiece from being torn from yourhands,thrown,spun by the tool,or shattered, alwaysproperlysupportyour workpiece as follow:a. Always positionBACKUP MATERIAL (used
beneath workpiece) so that it contactsthe leftsideof the column, or use the fence providedanda clamp to brace a small workpiece.
b. Whenever possible,positionthe WORKPIECE tocontactthe left side of the column. If it is too shortor the table is tilted, use the fence providedorclampsolidlyto the table, usingthe table slots.
c. When usinga drill pressvise, always fasten it tothe table.
d. Never do any work freehand (hand-holdingtheworkpiecerather than supporting it on the table),exceptwhen polishing.
e. Securelylockthe head and supportto the column,the table arm to the support,and the table to thetablearm, before operatingthe drill press.
f. Never move the head or the table while the tool isrunning.
g. Beforestartingan operation,jog the motor switchto make sure the drillor other cuttingtool does notwobble orcause vibration.
h. If a workpieceoverhangsthe table so itwill fall ortip if not held,clamp it to the table or provideauxiliarysupport.
i. Use fixturesfor unusualoperationsto adequatelyhold,guide, and positionworkpiece.
j. Use the SPINDLE SPEED recommended for thespecificoperation and workpiecematerial. Checkthe panel on the insidepulleycover or the chartbelowfor drillingspeed information.Foraccessories,refer to the instructionsprovidedwitheach accessory.
5. Never climbon the drill presstable, it couldbreakor pull the entire drill pressdown on you.
6. Turn the motor switch"OFF", and putaway theswitchkey when leaving the drillpress.
7. To avoid injuryfrom thrownwork or tool contact,donotperfornlayout, assembly, or set up work on thetable while the cuttingtool is rotating.
DRILLING SPEED TABLE (rpm)
Drill Bit Material
Diam. Wood 6.1umi- Plastic Mild Stain-
(Inches) mum Steel less
1/32 3100 3100 3100 3100 3100
16201/16 2620
1620 9901/8 2620 1550
990 6003/16 1550 650
1620 16201/4 2620 2620
600 3405/16 650 510
990 9903/8 1550 1550
1630 340 2507/16 2620 510
600 6001/2 650 650
9/16
5/8
18
POSITIONING THE TABLE AND WORKPIECE(FIG. Y and Z)1. Lockthe table (1) to the column(2) at a positionso
the tipof the drillbit (3) is just abovethe topof theworkpiece(4).
2. ALWAYS place a BACK-UP MATERIAL (scrapwood)on the table beneath the workpiece.This willpreventsplinteringor heavy burringon theundersideof the workpiece. To keep the back-upmaterial from spinning out of control, it MUSTcontact the LEFT side of the column.
To prevent the workpiece or backup material from beingtorn from your hands while drilling, you MUST position itagainst the LEFT side of the column. If the workpiece orthe backup matedal is not long enough to reach thecolumn, use the fence provided with the drill press tobrace the workpiece. Failure to do this could result inpersonal injury.
HOLDING A DRILLING LOCATION1. Usinga centerpunchor sharp nail,make an
indentationinthe workpiecewhereyouwant thehole.
2. Usingthe feed handles,bdng the drilldownto alignwiththe indentationbefore turningthe drillON.
TILTING THE TABLE (FIG. AA)NOTE: The table arm and support (1) has a preddlled
hole with a locking set screw inserted for locking thetable into a predetermined 0 ° horizontal position.
1. To use the table in a bevel (tilted) position, turn thelocking set screw (2) with the hex keycounterclockwise to release it from the table
support.2. Loosen the large hex head bevel locking bolt (3).
_t
To prevent injury,be sure to hold the table& tablearm assembly, so it will not swivel or tilt.
Fig. Y2
Fig. AA
\
3. For small pieces that cannot be clamped to thetable, use a drill press vise (optinal accessory).
The drill press vise MUST be clamped or bolted to thetable to avoid injury from a spinning workpiece, ordamaged vise or bit parts.
Remove the drill press fence when it interferes with otherdrill press accessories.
Fig. Z
3. Tilt the table, aligning the desired anglemeasurement to the zero line opposite the scale (4).Tighten the bevel locking bolt.
4 To return the table to its original position, loosenthe bevel locking bolt (3). Realign the bevel scale (4)to the 0° position
5 Using the hex key, turn the locking set screw (2)clockwise to seat into the hole.
To avoid injury from spinning work or tool breakage,always clamp workpiece and backup materialsecurely to the table before operating the drill presswith the table tilted
FEEDING
1. Pull down the feed handles with only enough effortto allow the drill bit to cut.
2 Feeding too slowly might cause the drill bit to burn.Feeding too rapidly might stop the motor, cause thebelt or drill to slip, or tear the workpiece loose andbreak the drill bit
3. When drilling metal, it may be necessary tolubricate the drill bit tip with motor oil, to preventburning the tip.
19
MAINTAINING YOUR DRILL PRESS
For your ownsafety, turn the switch=OFF" and removethe plug from the power source outlet before maintainingor lubricatingyour drillpress.
Frequentlyblow out, usingan air compressoror dustvacuum, any dustthat accumulates insidethe motor.
A coat of automotivepaste wax applied to the table andcolumnwill help to keep the surfaceclean.
To avoidshock or fire hazard, if the power cord is worn orcut in any way, have it replaced immediately.
LUBRICATION
All of the drill pressball bearingsare packedwith greaseat the factory. They require no further lubrication.
Periodicallylubricatethe gear and rack, table elevationmechanism of the spindlethe rack (teeth) of the quill.
20
TROUBLESHOOTING GUIDE
To avoid injuryfrom an accidentalstart, turn the switch"OFF" and always removethe plug from the power source beforemakingany adjustment.• Consultyour local Sears Service Center iffor any reason the motor will notrun.
PROBLEM
Noisyoperation
Drill bit burn.
Run outof drill bit point -drilled hole not round.
Wood splinters onunderside.
Workpiece torn loose fromhand.
Drill bit binds inworkpiece.
Excessive drill bit runoutorwobble.
Quill returns too slow ortoo fast.
Chuck will not stayattached to spindle. It fallsoff when trying to install.
POSSIBLE CAUSES
1. Incorrectbelt tension.
2. Dry spindle.
3. Loose spindlepulley.
4. Loose motor pulley.1. Incorrect speed.
2. Chips notcomingout ofhole.
3. Dull drill bit.4. Feeding too slowly.5. Not lubricated.
1. Hand grain in wood orlengths of cutting flutesand/or angles not equal.
3. Resharpen drill bit.4. Feed fast enough - allow drill to cut.5. Lubricate drill. See Section "BASIC DRILL
PRESS OPERATION-FEEDING"1. Resharpen drill bit correctly.
2. Replace drill bit.1. Use backup material. See Section "BASICDRILL PRESS OPERATION".
1. Support workpiece or clamp it. See Section"BASIC DRILL PRESS OPERATION".
1. Support workpiece or clamp it. See Section"BASIC DRILL PRESS OPERATION".
2. Adjust tension. See Section" ASSEMBLY -TENSIONING BELT".
1. Use a straight drill bit.2. Replace bearings.3. Install drill properly. See Section "BASIC
DRILL PRESS OPERATION" and"ASSEMBLY".
4. Install chuck properly. See Section"ASSEMBLY - iNSTALLING THE CHUCK".
1. Adjust spring tension. See Section"ASSEMBLY - ADJUSTMENTS -QUILLRETURN SPRING".
1. Using a household detergent, clean thetapered surface of the chuck and spindle toremove all dirt, grease and oil. See Section"ASSEMBLY - INSTALLING THE CHUCK".
21
15" DRILL PRESS PARTS LIST
When servicing use only CRAFTSMAN replacement parts•Use of any other parts may create a HAZARD or causeproduct damage,
Any attempt to repairot replace electricalparts on this Ddll Press may create a HAZARD unless repair is done by aqualifiedservice technician.Repair service is availableat your nearest Sears Service Center•
Especiflcaciones de la Herramienta ................................................... ............................. 26Instrucciones de Segutidad ....................................................................................... 27Accosorios y Aditamentos ....................................................................................... 30Contenido de la Caja ................................................................................................ 30Farniliarizares con la Prensa Taladradora ................................................................ 32Glosario de T6rminos ............................................................................................. 33
Ensamblaje y Regulaci6n ........................................................................................ 34
Guia para Diagn6stico de Problemas ......................................................................... 45Partes ...................................................................................................................... 46
GARANTJA TOTAL DE 1 ANOSiesta herramienta presentase defectos de material o fabricacibn dentro del primer argoa partir de la fecha de
compra, Sears la reparar_ sin costo alguno
Contactarse con un Centro de Servicio de Sears pare la reparacibn.
Siesta herramienta se usa para fines comerciales o para alquiler, esta garantia se aplica s61o per los primeros 90
a partir de la fecha de compra.
Esta garantia le otorga derechos legaLes espec{ficos y tambi_n podrla usted tener otros derechos que varian de unestado a otto
Sears, Roebuck and Co., Dept. 8t7 WA, Hoffman Estates, IL 60179
r.,_
Certaines poussieresprovenant d'activit6ssur outils_lectdques, comme ponc..age,sciage, meulage, pelage et d'autres activit_srelatives a la construction contiennent des produits chimiques connues pour causer cancer, anomalies congenitales ou autres dsquespour la reproduction. Certains exemples de cos produits chimiques sont :• plomb provenant de peintures _ base de plomb ;• silice cristallisee provenant des bdques et du ciment et d'autres produits de ma<;onnerie, et• arsenic et chrome provenant du bois chimiquement traite.Vos dsques d'6tre expos6 _ces produits vadent selon le temps pass6 &faire ce type de travail. Afin de reduire rexposition & cosproduits chimiques, il faut travailler dans un endroit bien a6r6, et porter de I'_quipement de securit6 approuve comme des masquespoussi6re congus sp6cialement pour ]e filtrage de particules microscopiques.
(No incluye el foco)TAMAI;IO DE LA MESA.....13-1/4"x13-1/4" (33.6 cm x 33.6 cm)INCLINACION
DE LA MESA ...................... 45 ° A LA DERECHA O IZQUIERDADESPLAZAMIENTO
DEL EJE .............................. 3-1/8"(8 cm)CUELLO ............................... 7-1/2"(19 cm)TAMA_IO DE LA BASE-=....11")(20-3/8" (28 cm x 52 cm)ALTURA ............................... 63-1/4"(1.61 m)
El polvocreado per el lijado mecanico, aserrado, rectificado,taladrado y otras actividades empleadas en construcci6ncontiene productos quimicos que se sabe causan cancer,defectos congenitos u otros daSos al sistema reproductor.Algunos de estos productos quimicos son :• plomo proveniente de pinturas a base de plomo• silicecristalizada de ladnllos y cemento y otros productos de
alba_ileria y,• arsenico y cromo de madera tratada quimicamente.Su riesgo de exposicibn a estos productos varia dependiendode cuan a menudo usted hace este tipo de trabajo. Para reducirsu exposicibn a estos productos quimicos :trabaje en lugaresbien ventilados y utilice equipo de seguridad aprobado, talcomo mdscaras contra el polvo especialmente disefladas parafiltrar particulas microscopicas.
INSTRUCCIONES GENERALES DE 14.SEGURIDADANTES DE USAR LA PRENSATALADRADORA
Seguridad (no anteojos) que cumplancon la norrna Z87.1de ANSI. Los anteojosde uso diafiosSIotienen ]entesresistentes a losimpactos, estos NO SON galas deseguridad. I.as Gatas de Seguridad pueden adquirirse enSears. NOTA: Los anteojos o galas que no cumplen con lanorma Z87.1 de ANSI pueden causar daSosserlos alromperse.
CONSERVAR ESTAS INSTRUCCIONES
27
REGLAS DE SEGURIDADESPEC|FICASPARALA PRENSATALADRADOFIA
LA PRENSATALADRADORA DEBE ESTAREMPERNADA en formaseguraal banco de trabajo.Adicionalmente,si hubiese la tendenciaa que elbancode trabajoTaladradorase muevaduranteciertasoperaciones,empernarla prensaal piso.
11. CERCIORARSEqueno hayanclavosniobjetosextrariosen laparte de lapiezaquesevaa taladrar.
14.
15.
t6.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.12. FIJARLAPIEZADETRABAJOCONSUJETADORES
contrael lado izquierdode la columnaparaevitarque gire.Si fuesemuycortao sila mesadela herramientaestuviese 27.indinada,sujetadafirmementea la mesay usar laguiaprovista.
13. SI LA PIEZA DETRABAJO se proyecta fuera de la mesade forma tal que se caiga o inclinesi no estuviese sujeta,sujetadaa la mesa o proveer un soporteauxiliar.
FIJARLA PIEZADE"rRABAJO,Cuandofuese_,usarsargentaso unaprensaparasujetarla plezadetrabaJo.Esn_a seguroqueusarla _ y dejalibreambasmanoeparaoperarla herramlerCa.
AL USAR unaprensaparataJadro,siempresujetadaala mesa.
Usar un ramal de circuito independiente para esta herramienta.Este circuito debe ser de un alambre cuyo calibre no sea menora 12 y debe estar protegido con un fusi_e de retardo de 15Amps. Antes de conectar el motor a la Iinea de suministroel@ctrico,carciorarse que el interruptor est@en la posici6n de='OFF"(Apagado) y que la corriente el_}ctdcasea la indicada en laplaca de datos del motor. Operar la herramienta con un voltajemanor puede daSar el motor.
Visitarel Departamantode Ferretedade la liendaSearsmdscercanaover el Catdlogode HerramientasEI6cbicas/Neun_ticasy Manualesde Searsparalossiguiantos_cesorios:
Si faltasanpiezaso hubiesenpiezasder3ades,noenohufarlaPrensaTaladradorahastaconseguirlaspiezasfaltanteso dereemplazarlasda_adasy basrahabercompletadeelensam_aje.
Per su propia seguddad, nunca enchufar en eltomacorriente haste haber completado todos lospesos del ensamblaje la regulacibe, y haste haberLeido y entendido ]as instrucciones de seguddad yoperaci6n.HERRAMIENTASNECESARIAS
DesarmadorPiano
Uave combinada
Llaveregufabdede 8"y 10"
[ I I I I I I I I I _ I1 I EscuadracomNnada
Escuadra Llave ratchet con dad<)
_23mm
La Prensa Taladradora es muy pesada y pareensamblarse en forma segura DEBE levantarse conla ayuda de 2 personas 0 mas.
SOPORTE DE LA COLUMNA A LA BASE (FIG. A)1. Colocar la base (1) en el piso.2. Colocar ]a columna (2) en la base alineando los
orificiosen el soporte de la columna con losorificiosde la base.
3. Ubicar los cuatro pemos hexagonales largos (3)en la boise con piezas sueltas.
4. Colocar un perno en cada orificio del soporte dela columna y de la base Ajustar con una Ilaveregulable.
Fig. A
INSTALACI(_N DE LA MESA (FIG. B y C)1. Ubicar la manivela de la mesa (1) y el seguro del
sop6rte (2) en la boise con piezas sueltas.2. Inserter el manguito del seguro del soporte en el
orificio (3) que estb en la parte posterior delseporte de ]a mesa Ajustar a mane.
3. Instalar la manivela en el eje pequet_o(4), alinearel perno de fijacion (5) con la superScie plane deleje. Ajustar el perno'de fijaci6n con una Ilavehexagonal
4. (FIG. C) Aflojar el seguro det soporte (2). Elevarel brazo de la mesa girando la manivela (1) en elsentido del reloj. Ajustar ta manija del seguro dela mesa.
5. Colocar la mesa (6) en el brazo de la mesa.Ajustar la manija (7) del seguro de la mesa.
Fig. C6
INSTALACI(_N DEL ALA DE EXTENSION
1. Coloque el mango (OWVG) en el tubo superior
(OWVH).2. Inserte las arandelas pfanas (OJ6T) en los
tomilloshexagonales (OJUB). Inserte el pemo (OJUB) enel tubo superior (OWVH) y apri_telo.
3. Inserte los tomillos hexagonales (OJUB) en eltubo superior (OJUB) y apd6telos.
4. Coloque el conjunto del tubo superior debajode la mesa.
5. Coloque el conjunto de places (OWVJ) en elpemo de cierre (OWVK). Inserte el conjunto deplaces en la mesa y apd6telo.
NOTA: si es necesado ajustar la Iongitud,afloje elperno de cierre (OWVK) hasta alcanzar laIongitud deseada y vuelva a apretado.
1. Levantarel cabezal(1) cuidadosamentesobrela columna(2)y deslizarlaen la columna.Cerciorarseque el cabezalsedeslicetan abajoen la columnacomosea posible.Alinearelcabezalconla base.
2. Usandouna,ave hexagonal,ajustarlosdospernosdefijacibn(3) en el ladoderecho del cabezal.
ENSAMBLAJEDE LA GU_ (RG. F)EstaPrensaTaladradom_eneuna masaconla superficieacanalada.1. Determinarla ubicack_deseadaparala gufa(1).
DeslizarlosbloquesT (2) en loscanalesadecuadoscomosemuestra.
2. Alinearlosorificiosde montajede la gufasobrelosorificiosroscadosen losbioquesT.
3. Colocarunaarandela(3) en la espigaroscadade laperilla(4). Insertar la espigade la pedllaen el orifidode montajede la guia en e]bloqueT y ajustar.
NORA:El brazo y el soportede la mesa ya vienen con un orificioque trae insertadoun tomillopara fijar la mesa en una posici6nhorizontalpredeterminadade 0°. Aflojar.eltornilloparacambiar el_ngulo de la mesa.
Paraevitar lesiones,cerciorarsedesujetarta mesay el brazedela mesade tal formaque nogireni se incline.
6. Alinaarlaescuadracon el v_stagogimndela mesahastaquela escuadrayel vdstagoquedenalineadas.
7. Volveraajustarelpernohexagonalgrande(6).
Fig. L
5
6
47
ESCALADEINCLINACI6N(FIG,L y M)
NOTA: Se ha induido la escala de inclinaci6n paramedir el&ngulo de indinaci6nen formaaproximada.Si sa requiemprecisi6npara la posici6nde la mesa, se debe utilizarunaescuadra uotra herramientade medici6n.Para usar la escala de
inclinaci6n(7):
1. Aflojarelpernodefljaci6n(4) paraSOLTARLOdelsoportede la mesa.
2. Aflojarelpernograndede cabezahexagonal(6)quefija lainclinaci6nde la mesa.
Parae_r lesionespecsona_ siempredesco_ el enchubdelton_,co,-den_antesdehanercualquierreguladdn.
F OnT A (RG.N)Girarlasmanijasde avancecontrael sanlJdodelrelojparebajarel ejehastesuposiciderndsbaja.Sujetarel ejefirmementeconla manoymovedohaciaatrdsy haciaadelantesobresusje.Situviesedemasiadojuego,hacerIosiguiente:1. Aflojarb contratuerca(1).2. Paraeliminarel juego,girarla puntaranuradadetperno(2)
en elsentidodelreloj,perusinobstruirel rnovimientohadaarribaqueel eje tiene.(Unpeque6ojuegodeleje asnormal).
3. Ajustarla contmtuerca(1).
Fig. N
RESORTEDE RETORNODE LAMORTAJA(FIG.O)Elresortede retomode la mortajapodr_arequerirregulacibnsisutensi6nhaosquelamortajaregrasedemasiadordpidoodemasiadelento.
1. Bajarla mesapareIograrunamayorseparaci6n.2. Colocarundesarmadoren la ranura(1)frontalinferiorde la
3. Conel desarmadoraunenganchadoen la ranura,aflojarlatuercainterior(4) justohastaque la ranura(5)sadesenganchede susujetador(6)enel cabezalde la PreosaTaladradora.
CUIDADO: NO SACAR ESTA TUERCA INTERIOR,
porqueel rasorlese desbobinardcon fuerza.
4. Usandoundesarmador,girarcuidadosamentelatape(2)delresortecontrael sentidodelrelojhastaque la siguienteranuraenganche.
6. Si la mortajasemuevehaciaarribay haciaabajoconlafacilidaddeseade,ajustarla tuercaestdndar(4)conunaIlaveregulable.Siestuviasedemasiadofloja,repetirlospasos2 al 5 paraajustarla.Si estuviasedemasiadoajustade,ejecutarlospasos4 y5 ala inversa.
7.
NO SOBREAJUSTARnirestringirelmovimientodelamortaja.
Pareevitarlesionesdsbidesa unarranqueaccidental,antesdehacerajustesalas coneas,SIEMPREcerciorarsequeelintermptore_6 en la posici6n=OFF"(Apagado),quela Ilavedelinterruptorhayasidoretiraday queelenchufenoest6conectadoal tomacorTiente.
TENSI(_NDE I.AS CORREAS(FIG.P)Cerciorarsequelaspoleasest6ndebidamentealineadascomasemuestraen la RguraR en lapdgina15.1. Pareaflojarlatensi6nde lacorrea,girar(contrael sen_do
4. Volvera ajustarlascorreasgirandoen elsentidodelrelojlamanijatensionadora(1), hastaque lacorreasedefle_ione1.2 cm(1/2")al presionarlacorreaen el msdio.
NOTA:Refedrsea latablaquese encuentraen la parteinteriorde la cubiertaprotectomde lascorreas,paraobtenerlasposidonesdelaspoleasrecomendadasparalasdistintasvelocidadesdetaladrado.
5. " Ajustarlossegurosde la manijatensionadora(4),girdndolosen elsentidodelreloj.
6. Paraevitarquela piezade trabajoselevantede la mesaelelevarlabroca,sostenedade la partesuperiorcon la manoocon sujetadores.
Fig. U
234
Para evitar lesioneso acoidentes causados por la Ilavedel mandrilsaliendo disparada con fuerza cuando se active la PrensaTaladradora, s61ousar la Ilavede mandril autoeyectante provistacon esta Prensa Taladradora. SIEMPRE verificar y retirar la Ilavedel mandril antes de activar la Prensa Taladradora.
4O
TALADRADOA UNA PROFUNDIDADESPECIFICA(RG.V)Cuar_ se deseatalad_ unoritUodegohastaunaprofundk_espemca¢na_=ar _ pk3zacompk_amem,sep.edenhacerdoscocas:
Uitodo: Uundo la Pie_ €leTrldx_
1, Marcarlaprofundidad(1)delorifidoelco6"tadode la pieza,2. Conel intenuptoren"OFF"(Apegado),bajarlabrocahasta
b) Siemprequeseaposible,colocarLAPIEZADETRABAJOdetal maneraquehagacontactocon la parteizquierdade lacolumna.Sifuesemuycortao sila mesaestuvieseinclinada,usarla guiaprovistao sujetarlaenformaseguraa la mesa,usandolasranuras.
c) Cuandosa useunaprensasujetadoraparataladro,siempreasaguradaa la mesa.
d) Nuncatrabajarsosteniendola plazaquesa taladras61oconla manoy sinsujetarlaa la mesa,excoptoal pulir.
e) Fijarel cabezatenformaseguray elsoportea lacolumna,el brazode la mesaal soportey lamesaalbrazode la mesaantesde operarla PrensaTaladradora.
3. Para piezas pequefias que no se puedan fijar a la mesa consujetadores, usar una prensa para taladro (accesorio opcional).
LaprensaparataladroDEBEsujetarseo empemarsea la mesaparaevitarque lapiezade tmbaiogirey causelesionesaloperadoro dafiosa la prensao a la broca.Retirarla guiacuandointeffieraconlosotrosaccesofiosde laPrensaTaladmdora.
Fig. Z Paraevitarque la piezade trabajogireycauselesioneso tampala bresa,siemprefijarla piezadetrabajoy el materialde apoyoala mesacon sujetadoresantesde hacerfuncionarla PrensaTaladradoracon la mesaindinada.
Todosloscojinetesde bolasde la PrensaTaladradoravienenrellenosde grasadesdela f_brica. Norequierenlubrisaci6nadicional.
Lubdcarperibdicamentelosengranajesy la cremallera,elmecanismode elevacibnde la mesa,el eje deltaladroy lasmandfbulasde su mortaja.
44
GUfA PARADIAGN( )STICODE PROBLEMAS
PareeviWIRionesocaslonadupotunmnmqueacdd_tal, moverel Intem¢_ a la posld_ de 'OFF"(_) y _ _cord_ de sumlnls_delton_corrientem de hacercualqu_ regulaci6n,• Consultaral CentredeSen_doSeamlocal_ el molornoammcMe potcualqulermo_w
PROBLEMA SOLUCI6N
Operac_ nddo_
La brocaseq.ern_
Se _mlala_r_ _ la
Regular.laten_ Vet lasecd6n"ENSAMBI._E-TENSIONDE LACORREA'.Lubdcarel eje.Vetla secci6n"LUBRICAClON'.Asegummequelatuercade retenck_de lapo_a est6ajusu_eyNumdeeHuesenece_a_Aiuetereli_no de ,jeck_ de la i_ea delmotor.
To purchase a protection agreement (U.S.A)or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6665 (u.s.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparacibna domicilio, y para ordenar piezas:
1-888-SU-HOGAR s"
(1-888-784-6427)
Au Canada pour service en franctais:
1-800"LE-FOYER "c
(1-800-533-6937)www.sears.ca
6EAR6
® Registered Trademark I TM Trademark / SMService Mark of Sears, Roebuck and CO® Marca Registrada / TMMarca de Fdbrica / sMMarca de Servicio de Sears, Roebuck and Co