Operator Site Plan Model HCTDCU SPECIALTY … HCTDCU SPECIALTY OVERHEAD DOOR AND GATE OPERATOR OUT Interrupt Loop Exit Loop Shadow Loop IN OUT Interrupt Loop Exit ... Plug-In Loop
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Mo
del
HC
TD
CU
SP
EC
IALT
Y O
VE
RH
EA
D D
OO
R A
ND
GAT
E O
PE
RAT
OR
OUTInterruptLoop
ExitLoopShad
owLoop
IN
OUTInterruptLoop
ExitLoop IN
Shadow
Loop
OUOUUUOUOU
OUOUOUOUOUOUOUOUOU
OUOUOUOUOUOUOUOUOUOUOUOUOUOUOUUOUOU
Batteries7AHStandard 7 AMP-Hour Battery, 12 Vdc, to replace original batteries provided with operator. Reuse existing harnesses.
Plug-In Loop DetectorIncludes 8 sensitivity settings and boost, ensures vehicles are easily identifi ed.
Internet Protocol Door Controller Cost effective, fl exible cloud-based accessgate/door controller for perimeter and interior entrances.
Universal DIP Single-Button and 3-Button Remote ControlThese remote controls are ideal for applications such as gated communities or commercial applications requiring a large number of remotes for a common entrance.
2-Button and 4-Button Security+ 2.0® Learning Remote ControlsThese remote controls are ideal for gated communities. One button can control a gate operator and the other(s) can control a garage door. It can also be programmed to different codes and frequencies.
MODEL HCTDCUPIVOT GATE EXAMPLE
SECTIONAL DOOR EXAMPLE
ACCESSORY OVERVIEW
Operator Site Plan
Entrapment Protection DevicesThis operator contains an inherent (internal) entrapment protection system and REQUIRES the addition of a LiftMaster external monitored entrapment protection system (non-contact photoelectric sensor or contact edge sensor) for EACH entrapment zone prior to gate/door movement. Model CPSUN4G is provided with operator. See back page.
LiftMaster gate operators comply with UL 325 standards. IMPORTANT: To be compliant with UL 325 and industry safety guidelines, LiftMaster qualifi ed monitored external entrapment protection devices such as photoelectric sensors or edge sensors are required to be installed with this operator.
Red/Green Traffi c Light:Indicates the gate/door position. Provides assurance of safe entering and exiting of the facility, reducing the potential for costly accidents.
ENTRAPMENT PROTECTIONINSTALLATION OVERVIEW
CONTACT SENSORS (EDGE SENSORS)
POWER WIRING
MOUNT THE OPERATOR
OPERATOR DIMENSIONS
DETERMINE LOCATION FOR OPERATOR
OPERATOR SPECIFICATIONS
NOTE: Use copper conductors ONLY.
This operator contains an inherent (internal) entrapment protection system and REQUIRES the addition of a LiftMaster external monitored entrapment protection system (non-contact photoelectric sensor or contact edge sensor) for EACH entrapment zone prior to gate movement. An entrapment zone is every location or point of contact where a person can become entrapped between a moving gate and a stationary object. Your application may contain one or many entrapment zones. System includes six monitored entrapment protection inputs capable of covering all entrapment zones. Use only LiftMaster approved entrapment protection devices.
NON-CONTACT SENSORS
Model LMWEKITULiftMaster Monitored Wireless Edge Kit (Transmitter and Receiver)
Model L50, L504AL, L505AL, and L506ALLarge Profi le Monitored Edge (82 ft. roll)Aluminum Channel (4 ft., 5 ft., 6 ft.)
Model L50ELarge Profi le Ends Kit (10 pairs)
Model S50, S504AL, S505AL, and S506ALSmall Profi le Monitored Edge (82 ft. roll)Aluminum Channel (4 ft., 5 ft., 6 ft.)
Model S50ESmall Profi le Ends Kit (10 pairs)
Model L50CHPPVC Channel for Both Large and Small Profi les (8 ft., pack of 10)
Model LMTBULiftMaster Monitored Through Beam Photoelectric SensorModel LMRRULiftMaster Monitored Retro-Refl ective Photoelectric SensorModel CPSUN4GLiftMaster Monitored Through Beam Photoelectric SensorNOTE: CPSUN4G is provided with the operatorModel CPS-OPEN4LiftMaster Monitored Dual-Sided Photoelectric Sensor
Model L50CHALAluminum Channel for Both Large and Small Profi les (10 ft., pack of 8)
Main AC Supply 120 Vac, 4 Amps OR 240 Vac, 2 AmpsSystem Operating Voltage 24 Vdc Transformer Run / Battery Backup
Accessory Power 24 Vdc, 500mA max. for ON + SW (switched)Solar Power Max 24 Vdc at 60 watts max.Variable Operating Lengths (Operator Weights)
8 foot (2.4 m) gate - 11.75 foot (3.6 m) operator length (130 lbs. [58.9 kg])10 foot (3.1 m) gate - 13.75 foot (4.2 m) operator length (145 lbs. [65.7 kg])12 foot (3.7 m) gate - 15.75 foot (4.8 m) operator length (160 lbs. [72.5 kg])
Maximum Gate/Door Weight 700 lbs. (317.5 kg) Maximum Gate/Door Width (sectional and one-piece)Maximum Gate/Door Height
22 ft. (6.7 m)
12 ft. (3.7 m)Travel Speed BIPART Delay OFF (Default) - 8 inches (20.3 cm) per second
BIPART Delay ON (Fast) - 11 inches (27.9 cm) per second (open speed only)Maximum Daily Cycle Rate ContinuousMaximum Duty Cycle ContinuousOperating Temperature -20°C to 60°C (-4°F to 140°F)Expansion Board Provided
Inherent Entrapment Protection (Type A)
Dual - RPM and Current Sense
External Entrapment Protection (Type B1 and/or Type B2)
3 inputs per board - any combination of up to 3 photoelectric sensors and up to 2 edge sensors
Power Wiring Sockets (120 Vac factory default)
EMI BOARD
Input Power Connection
HOT
NEUT
RAL
GROU
ND
Black
Green
White
Whi
te
Red
Piggy Back
AC PowerSwitch
Power Wiring Connector
Use UL listed conduit to enclose power wires
American Wire Gauge (AWG)
Maximum Wire Length (120 Vac)
Maximum Wire Length (240 Vac)
14 130 feet (39.6 m) 260 feet (79.3 m)
12 205 feet (62.5 m) 410 feet (125 m)
10 325 feet (99.1 m) 650 feet (198.1 m)
8 520 feet (158.5 m) 1040 feet (317 m)
6 825 feet (251.5 m) 1650 feet (502.9 m)
4 1312 feet (399.9 m) 2624 feet (799.8 m)
2. Open the gate/door and mark the center point on the ceiling.1. With the gate/door closed, mark the center.
1. Place the motor unit on packing material to protect the cover. Make sure the header bracket is in the center of the opening. Bolt or weld the header bracket to the wall.
2. Lift the operator and align with center mark on ceiling. Have someone hold the operator in place or use a post as a temporary support. Bolt the operator to the ceiling. (A support post is not part of the operator. Use only for installation.)