OPERATION MANUAL - 6 - 2 - 1. EXTERNAL ALARM MESSAGE 1.1 Not ready Not ready Keeping press O.T release (this button will be lighted off) and move the axis to inside of the working area by jog or handle . (opposite direction operating) Release O.T release 1031 spindle motor alarm on CRT? Any axis overtravel?(O.T release will be lighted on operator panel) Not ready? END Refer to 1031 spindle motor alarm for trouble shooting. Release it. Electric problems , call for service. Y Y Y Y N N N N Any emergency stop button pressed on operating pannels?
33
Embed
OPERATION MANUAL - · PDF filePlease refer to FANUC maintenance manual if NC screen displayed NC alarm. ... OPERATION MANUAL - 6 - 23 - 1060 PMM SERVO
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
OPERATION MANUAL
- 6 - 2 -
1. EXTERNAL ALARM MESSAGE 1.1 Not ready
Not ready
Keeping press O.T release (this button will be lighted off) and move the axis to inside
of the working area by jog or handle . (opposite direction operating)
Release O.T release
1031 spindle motor alarm on CRT?
Any axis overtravel?(O.T release will be lighted on operator panel)
Not ready?
END
Refer to 1031 spindle motor alarm for trouble shooting.
Release it.
Electric problems , call for service.
Y
Y
Y
Y
N
N
N
N
Any emergency stop button pressed on operating pannels?
OPERATION MANUAL
- 6 - 3 -
1.2 NC alarm
Please refer to FANUC maintenance manual if NC screen displayed NC alarm. The NC alarm includies. 1. program error (P/S alarm) 2. the absolute pulse coder alarm (APC) 3. servo alarm 4. overtravel alarm 5. alarm in PMC 6. overheat alarm 7. system alarm 8. background edit alarm (BP/S)
OPERATION MANUAL
- 6 - 4 -
1.3 Outside alarm message
1001 START INHIBIT
Alarm1001
Does chuck clamp ok?
END
Reset
Is there door interlock switch?
K2.1 setting 1 Make sure door close
X11.3=1? Press door release
Electric problem call for service
1
1
For chuck inside or outside clamp memory changing please reference to appendex A.1
2
Y
Y Y
Y
N
N
N
N
By pass it?
2,
OPERATION MANUAL
- 6 - 5 -
1002 X AXIS ZERO RETURN INHIBIT
Alarm1002
Reset
Do you want Z axis zero return before X axis zero return?
X axis zero return first and then Z axis zero return
END
Setting K4.7=1 This bit will be set to 0 ,
automatically once power on.
N
Y
OPERATION MANUAL
- 6 - 6 -
1003 AUXILIARY MOTOR OVERLOAD
Alarm1003
Coolant pump overload?
Lube unit motor overload?
Oilmatic motor overload?
Chip conveyor motor overload?
Remove the cause of overload.
Reset the overload relay of the motor.
The alarm still there?
END
Electric problem , call for service.
Y
N
Y
Y
Y
N
N
Hydraulic motor overload?
N
N
OPERATION MANUAL
- 6 - 7 -
1004 OIL MATIC FAILED
1005 DOOR NEED CLOSED!
Alarm1004
Is there alarm display on the oilmatic machine panel?
Please refer to the manual of the oilmatic machine to solve problem
END
N
Y
Reset
Please refer to electric manual,check the signal X5.7 circuit, find short point
and remove it.
Alarm1005
Reset
Safety door open?
Close safety door before executing program start.
END
K11.3=1?
Y
Y N
N
Electric problem , call for service
OPERATION MANUAL
- 6 - 8 -
1006 TOOL LIFE EXHAUST
1007 PART COUNT REACHED
Alarm1007
Reset
Alarm1006
Reset
END
Install tool life counting. 1. tool life screen 2. move curser to install tool
group. 3. select the soft key<oprt> 4. select the soft key<clear> 5. select the soft key<exec>
END
Install part counting. 6. part count screen 7. select the soft key<oprt> 8. select the soft key<clear> 9. select the soft key<exec>
OPERATION MANUAL
- 6 - 9 -
1008 AXIS NEED ZERO RETURN
Alarm1008
Machine service?
END
Reset
Setting K4.7=1 *the bit will be set to 1 after power off and power on.
Execute all axis ZERO return after power on
Y
Y
N
Set K3.7=1
Have been executed machine lock?
Set K3.6=1
All axis ZERO return.
N
OPERATION MANUAL
- 6 - 10 -
1009 OIL PRESSURE FAILED
Alarm1009
Is oil pressure enough?
Press reset or cycle start push button.
Alarm 1009 DGN X12.5=1?
END
Adjust the oil pressure to be correct. (X9.5 = 1 )