Series KJ One-Touch Mini Fittings Fittings & Tubing 1412 One-Touch Mini Fittings Applicable Tubing Series KJ Specifications Features � Applicable tubing O.D. : Metric Size � Connecting thread : M3, M5, R1/8 Fluid Max. operating pressure Operating vacuum pressure Proof pressure Ambient and fluid temperature Thread Thread label (Standard) For application requiring copper-free material (Standard) Air, Water Note1) 1.0MPa –100kPa 3.0MPa –5 to 60˚C, In case of water: 0 to 40˚C (with no condensation) JIS B0203 (Taper thread for piping) JIS B0209, Class 2 (Metric coarse thread) JIS B0211, Class 2 (Metric fine thread) With sealant Brass parts are all electroless nickel plated. Mounting Nut Note1) Applicable to general industrial water. Consult SMC if using for other fluids. Surge pressure must be under the maximum operating pressure. Tubing material Tubing O.D. Nylon, Soft nylon, Polyurethane ø2, ø3.2, ø4, ø6 PAT. Chuck Applicable to nylon and polyurethane. Large retaining force. Secure engagement and large retaining force with chuck. Compatible with low vacuum to 1.0 MPa of pressure. The special shape ensures sealing and reduces resistance of tubing insertion. Requires little force for removal. Releases the chuck to remove the tubing. Prevents the chuck from biting too deeply into the tubing. Tubing removal is easier. Enables piping in a narrower space. Body and thread can be rotated (For positioning). Electroless nickel plated. R1/8 thread with sealant. Packing Stud Release bush (Light grey) O-ring Body (White) Tubing Gasket Guide 2 Guide 1 Outside diameter reduced by 20%(Compared with series KQ), allowing piping in a narrower space. Thread sealant as standard. For application requiring copper-free material. (Electroless nickel plating) Compatible with vacuum to –100 kPa of pressure. ø2 One-touch Mini Series KJ
90
Embed
One-Touch Mini Fittings KJ · Series KJ One-Touch Mini Fittings Fittings & Tubing 1414 KJH Straight Union Tubing Tubing KJH Different Diameter Straight KJE Bulkhead Union KJT Dfferent
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Thread label (Standard)For application requiring copper-free material (Standard)
Air, Water Note1)
1.0MPa
–100kPa
3.0MPa
–5 to 60˚C, In case of water: 0 to 40˚C (with no condensation)
JIS B0203 (Taper thread for piping)JIS B0209, Class 2 (Metric coarse thread)
JIS B0211, Class 2 (Metric fine thread)
With sealant
Brass parts are all electroless nickel plated.
Mounting
Nut
Note1) Applicable to general industrial water. Consult SMC if using for other fluids. Surge pressure must be under the maximum operating pressure.
Tubing material
Tubing O.D.
Nylon, Soft nylon, Polyurethane
ø2, ø3.2, ø4, ø6
PAT.
ChuckApplicable to nylon and polyurethane.Large retaining force.Secure engagement and large retaining force with chuck.
Compatible with low vacuum to 1.0 MPa of pressure.The special shape ensures sealing and reduces resistance of tubing insertion.
Requires little force for removal.Releases the chuck to remove the tubing.Prevents the chuck from biting too deeply into the tubing.Tubing removal is easier.
Enables piping in a narrower space.Body and thread can be rotated (For positioning).Electroless nickel plated.R1/8 thread with sealant.
Packing
Stud
Release bush (Light grey)
O-ringBody (White)Tubing
Gasket
Guide 2Guide 1
Outside diameter reduced by 20%(Compared with series KQ), allowing piping in a narrower space.
Thread sealant as standard.
For application requiring copper-free material. (Electroless nickel plating)
Compatible with vacuum to –100 kPa of pressure.
ø2 One-touch MiniSeries KJ
One-Touch Mini Fittings Series KJ
Fitti
ngs
& T
ubin
g
1413FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
M3M5
2
M3M5
2
2M3M5
2M5M3
KJH Male Connector
Tubing Female thread hole
3.2
4
6
M5
M3
M3
M5
M5
KJH02-M3 -M5KJH23-M3
-M5 -01S
KJH04-M3 -M5 -01S
KJH06-M5 -01S
Most common style used to pipe from female thread in the same direction.
<M3, M5>
<R1/8>
<R1/8>
The hexagon socket in the body is used to tighten the socket head male connector with a hexagon wrench. Useful in a confined space.
Applicabletubing O.D.
mm
3.2
6
4
Connecting thread
M3
M3
M5
M5
M5
Applicabletubing O.D.
mm
Connecting thread Model
KJS02-M3KJS23-M3
-M5KJS04-M3
-M5 -01S
KJS06-M5 -01S
Model
<R1/8>
To branch the line from the female thread at 90˚ in each direction.
<M3, M5>
Applicabletubing O.D.
mm
M3
M3
M5
M5
3.2
4
6
Connecting thread
M5
KJT02-M3 -M5
KJT23-M3 -M5 -01S
KJT04-M3 -M5 -01S
KJT06-M5 -01S
Model
<M3, M5>
<R1/8>
Most common style used to pipe from female thread at a right angle.
Applicabletubing O.D.
mm
3.2
6
4
Connecting thread
M3
M3
M5
M5
M5
KJL02-M3 -M5
KJL23-M3 -M5 -01S
KJL04-M3 -M5 -01S
KJL06-M5 -01S
Model
<M3, M5>
<R1/8>
To branch the line from the female thread in the same direction and at 90˚.
<M3, M5>
Applicabletubing O.D.
mm
M3
M3
M5
M5
3.2
4
6
Connecting thread
M5
KJY02-M3 -M5
KJY23-M3 -M5 -01S
KJY04-M3 -M5 -01S
KJY06-M5 -01S
Model
3.2
4
6
M5
M5
M5
KJU23-M5 -01S
KJU04-M5 -01S
KJU06-M5 -01S
To branch a tubing in the same direction.
<M5>
<R1/8>
Applicabletubing O.D.
mm
Connecting thread Model
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
R1/8
KJS Hex Socket head Male ConnectorKJT Male Branch Tee
KJL Male Elbow KJY Male Run Tee
KJU Branch “Y”
2 M3
<R1/8>
Basically used in the same way as a male elbow.But also used in 3 dimensional piping to prevent interference of fittings.
<M3, M5>
Applicabletubing O.D.
mm
M3
M3
M5
M5
3.2
4
6
Connecting thread
M5
KJW02-M3 -M5KJW23-M3
-M5 -01S
KJW04-M3 -M5 -01S
KJW06-M5 -01S
Model
R1/8
R1/8
R1/8
KJW Extended Male Elbow
M3M5
2
Series KJ One-Touch Mini Fittings
Fittings & Tubing
1414
KJH Straight Union
Tubing Tubing
KJH Different Diameter Straight
KJE Bulkhead Union KJT Dfferent Diameter Tee
KJL Union Elbow KJU Different Diameter Union “Y”
KJT Union Tee
To connect tubing in the same direction.
Applicable tubing O.D.mm
3.246
KJH02-00KJH23-00KJH04-00KJH06-00
Model
To connect tubing through a panel.
Applicable tubing O.D.mm
23.246
KJE02-00KJE23-00KJE04-00KJE06-00
Model
3.246
To connect tubing at right angles to each other.
Applicable tubing O.D.mm Model
KJL23-00KJL04-00KJL06-00
23.246
To branch tubing into 2 directions each at 90˚ to the original one.
Applicable tubing O.D.mm Model
KJT02-00KJT23-00KJT04-00KJT06-00
23.246
To branch tubing in the same direction.
Applicable tubing O.D.mm Model
KJU02-00KJU23-00KJU04-00KJU06-00
To connect tubing of different diameters.
Applicable tubing O.D.mm
2
3.2
4
b3.24466
KJH02-23 -04KJH23-04
-06KJH04-06
Model
To branch the tubing into two at a right angle and reduce the resulting branches in size.
Applicable tubing O.D.mm
a3.24
b46
KJT23-04KJT04-06
Model
2- a b
ba
To branch tubing into 2 smaller tubing in the same direction as the original one.
Applicable tubing O.D.mm
a22
3.24
b3.2446
KJU02-23KJU02-04KJU23-04KJU04-06
Model
2- a
b
a
KJU Union “Y”
2
One-Touch Mini Fittings Series KJ
Fitti
ngs
& T
ubin
g
1415FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
KJL Plug-In Elbow
Tubing One-touch fittings
KJU Plug-In “Y”
KJR Plug-In Reducer KJX Reducer Union Plug-In “Y”
KJL Reducer Elbow
KJF Female Connector
To change the tubing direction from a one-touch fitting by 90˚.
Applicabletubing O.D.
mm3.246
Aplicablefitting size
3.246
KJL23-99KJL04-99KJL06-99
Model
To connect to a smaller one-touch fitting.
Applicabletubing O.D.
mm
Applicablefitting size
3.2
4
4466
KJR02-04KJR23-04
-06KJR04-06
Model
To change the tubing direction from a one-touch fitting by 90˚ as well as to connect to a tubing of a smaller diameter.
Applicabletubing O.D.
mm
Applicablefitting size
3.2
4
466
KJL23-04 -06
KJL04-06
Model
To branch the line from a one-touch fitting into tubing in the same direction.
Applicabletubing O.D.
mm
Applicablefitting size
3.246
3.246
KJU23-99KJU04-99KJU06-99
Model
To branch the line from a one-touch fitting into smaller diameter in the same direction.
Applicabletubing O.D.
mm
Applicablefitting size
3.24
46
KJX23-04KJX04-06
Model
To pipe from the male threaded portion of a pressure gauge, etc.
Applicabletubing O.D.
mm
3.2
6
4
Connecting thread
KJF23-M3 -M5
KJF04-M3 -M5
KJF06-M5
Model
Tubing
M3M5M3M5M5
Male thread
2
KJP PlugTo plug unused one-touch fittings.
Applicablefitting size
2 KJP-02
Model
Series KQ2 One-Touch Fittings
Fittings & Tubing
1416
Applicable tubing diameter: Metric Size Connecting thread: M, R, Rc
Fluid
Max. operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Thread
Sealant (Thread portion)
Air, Water Note 1)
1.0MPa
–100kPa
3.0MPa
–5 to 60˚C, In case of water: 0 to 40˚C (With no condensation)
JIS B0203 (Taper thread for piping)JIS B0209, Class 2 (Metric coarse thread)
JIS B0211, Class 2 (Metric fine thread)
With / Without sealant
Mounting
Nut
Note 1) Applicable to general industrial water. Consult SMC if using for other fluids. Surge pressure must be under the maximum operating pressure.
ChuckApplicable to nylon and polyurethaneLarge retaining forceSecure engagement with chuck and large retaining force with collet.
Compatible with a wide range of pressure, from low vacuum to 1.0 MPa.The special shape ensures sealing and reduces resistance in tubing insertion.
Series KQ2: Light greySeries KQ : BlueRequires little force for removalReleases the chuck collet to remove the tube as well as to prevent the chuck from biting too deeply into the tubing.
Effective for piping in confined spaceThe body and thread portion can be rotated. (For positioning)
Packing
Stud
Release button
O-ringBody
Tubing
M, R, RcThread
ColletGuide
Series
Series KQ2Series KQ
Body
White
Black
Release button
Light grey
Blue
Tubing material
Tubing outside O.D.
Nylon, Soft Nylon, Polyurethane
ø3.2, ø4, ø6, ø8, ø10, ø12, ø16
Series KQ2: White bodySeries KQ : Black body
PAT.
KQ2/White body
One-Touch Fittings
Applicable Tubing
Series KQ2
Colour
Specifications
Wide range of pressures - Low vacuum (10 Torr) to 10 Bar (1.0MPa) pressure
Wide range of tube systems (3.2mm - 16mm OD tube)
Minimised resistance to air flow
Widest range of configuration available
Choice of body colour to suit customer application
Features
Uni-fitting seriesUniversal application to G, Rc and NPT areas
Also available
Imperial sizes
Contact SMC for details of these types.
A full range of SMC fittings is available tosuit imperial size tubing from 1/8 to 1/2”,with either European standard Metric and Rthreads or American standard UNF andNPT threads.
One-Touch Fittings Series KQ2
Fitti
ngs
& T
ubin
g
1417FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Hexagon Socket Head Male ConnectorThe hexagon socket in the body is used to tighten the socket head male connector with a hexagon wrench. Useful in a confined space.
Branch Universal Male Elbow KQ2Z/KQZThe hexagon head of the body is used to tighten the body with a box wrench. Used to branch the line. Elbow union for piping.
To connect a line from a male and female thread in the same direction as well as to branch it into 2 pipes at a right angle. Multiplex connections possible.
To plug unused one-touch fittings KQ2P (White), KQP (Blue).
Applicable fitting size
3.2468
101216
KQ2P-23KQ2P-04KQ2P-06KQ2P-08KQ2P-10KQ2P-12KQ2P-16
KQP-23KQP-04KQP-06KQP-08KQP-10KQP-12KQP-16
Model
KQ2P (White) KQP (Black)
(m) in the above table is the colour of the cap.See list bellow:B (Black), R (Red), YR (Orange), BR (Brown), Y (Yellow),G (Green), CB (Sky blue), GR (Gray), W (White), BU (Blue)
Connecting thread
To connect a one-touch fitting and R female thread.
The male thread for piping drasticallycuts piping manhours.
Suitable foe use with port thrads conformingto ISO1179 and ISO16030.
The seal gasket on the male thread for piping eliminates the need for pipe tape.
Fluid
Max. operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Thread
Air, Water Note 2)
1.0 MPa Note 3)
–100 kPa
3.0 MPa
–5 to 60C, In case of water: 0 to 40C (No freezing)
JIS B0207 (EN ISO228)
JIS B0211, Class 2 (Metric fine thread)
Mounting
Nut
Applicable Tubing
Specifications
Note 2) The surge pressure must be under the maximum operating pressure.Note 3) The amount of leakage is not zero, and so the use for holding vacuum such as a leak tester should be avoided.
The special rotary seal minimizes rotating torque and friction.
Low-torque, low-friction operation with oil containing slide bearing.
The ball bearing ensures low-torque rotation.
Series KS: BlueSeries KX: Light greyThe male connector is provided with a tubing rotation prevention mechanism.
Ball bearing
Cassette
Electroless nickel plating allows copper-free applications.Thread sealant is standardized.
Stud
Rotary seal
Slide bearing
Tubing material
Tubing O.D.
Nylon, soft nylon, Polyurethane
ø4, ø6, ø8, ø10, ø12
Applicable tubing O.D.
Rotating torque N·m
Allowable number of rotations S-1
PAT.
Rotary one-touch fittings for low-torque rotation.
Applicable to oscillating and rotating sections of robots etc.
For application requiring copper-free material (Electroless nickel plated)
R1/8 thread sealant is standardized.
Note1)
Rotary sealX ring shape minimizes friction while providing an excellent seal. Seal is fire and shock proof fluorine rubber. It proves against high friction heat in high speed rotation and longer life.
ScraperPrevents chips from entering the bearing parts.
Swivel Extended ElbowUsed to pipe tube at right angles to a female thread. Can be swiveledat any direction. Solid section moves fittings up above a workpiece.
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
M-3UL
Universal tee
ModelDescription ApplicationRemark(s)
ø3.18/2.18X M3
ø3.18/2 X M3
ø4/2.5 X M3
ø3.18/2.18X M3
ø3.18/2 X M3
ø4/2.5 X M3
M3 femaleX M3 male
M3 maleX M3 male
M3 female X M3 femaleX M3 male
M-3UT
NippleTo connect fittings and equipment or to connect 2 fittings.
M-3N
PlugTo plug unused M3 port.M-3P
GasketSealant (Thread portion)M-3G
M-04R-2
Plug-in reducer
To pipe polyurethane tubing.
M-32R-2
M-01AU-6
Barb fittings for soft tubing
To pipe soft nylon, polyurethane tubing.
M-01AU-4
Barb fittings for nylon tubing
To pipe nylon tubing.
M-01AN-4
Remark(s)
ø4/2.5 X R1/8
M-01AN-6ø6/4 X R1/8
ø4/2.5 X R1/8
ø6/4 X R1/8
ø2/1.2 X 3.2 mm
ø2/1.2 X 4 mm
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
M-3AU-2ø2/1.2 X M3To pipepolyurethane tubing.
M-3ALU-2ø2/1.2 X M3To pipepolyurethane tubing.
M-01H-6
Hose nipple
To pipe nylon, soft nylon, polyurethane tubing.
M-01H-4ø4/2.5 X R1/8
ø6/4 X R1/8
M-04F-2
Hose nipple
To pipe polyurethane tubing.
M-32F-2ø2/1.2
X 3.2 mmone-touch
ø2/1.2 X 4 mmone-touch
MaterialPVC
Self Align Fittings Series H, DL, L, LL
Fitti
ngs
& T
ubin
g
1439FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Self Align Fittings
Series H, DL, L, LL
Specifications
Features
Main Parts Material
Prevents tubing from deforming inwards.
Prevents tubing sliding during installation.The tubing holding mechanism gives the strong feeling when inserting the tubing and prevents the tubing from sliding when screwing in the tubing.
Flared inside diameter
Tubing holder
Large holding force by metal ferrule.Applicable to soft copper.(Not applicable to urethane tubing.)
Ferrule with no orientation.The non-oriented construction is free from mistakes and consequent working loss or accidents when inserting the ferrule into the fitting body are reduced.
Hardened ridge ferrule.The single bite construction with a strong ridge prevents breakage of ferrule when tightening.
Small pressure loss.A large flow rate is achieved with small flow resistance due to the construction without an insert.
Wide variety of styles and sizes.10 models including swivel styles and 5 tubing O.D. provide a wide range of fittings that will fit any application.
Note) The male elbow, male branch tee and service tee union with sealant are manufactured upon receipt of order.
With one-touch fitting.Applicable to nylon, soft nylon and polyurethane tubing.
Installation processes are considerably reduced.Simpler installation and less labour compared with use of numerous bulkhead unions for panel mounting.
Secure tubing retention.Tubing can be firmly connected to the multiconnector in one-step operation (with one-touch fitting).
No. of connecting tubesTwo types, with 6 and 12 connecting tubing, are available.
6
ModelApplicable
tubingO.D. mm
No. ofconnecting
tubingMulti-
connector Plug side Socketside
12
DMK6
DMK12
ModelApplicable
tubingO.D. mm
No. ofconnecting
tubingMulti-
connector Plug side Socketside
046
3.2mm4mm
2304
Tubing O.D.
612
612
No. of connecting tubing
Multi connectorPlug side
Socket side
—PS
Configuration
Accessories (Optional)Nil
Single side cover (1 pc.)Both sides cover (2 pcs.)
-C1C2
DMKHow to Order
SocketSocket case
U-ringSecure sealing.
Plug casePlug
The protrusion and recession on both surfaces can be fit for engagement at the prescribed position.
Clamp ringConnects the socket and plug.
PlateSpacer
Cover
Holder
PAT.
3.2
4
DMK6-23
DMK6-04
DMK6P-23
DMK6P-04
DMK6S-23
DMK6S-04
DMK12-23
DMK12-04
DMK12P-23
DMK12P-04
DMK12S-23
DMK12S-04
3.2
4
Series KDM Rectangular Multi-Connector
Fittings & Tubing
1446
Rectangular Multi-Connector
Applicable Tubing
Series KDM
Specifications
Features
Applicable tubing O.D.: Metric Size No. of connecting tubing: 10 or 20
Fluid
Max. operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Air
1.0MPa
–100kPa
1.5MPa
–5 to 60˚C (With no condensation)
Tubing material
Tubing O.D.
Nylon, Soft nylon, Polyurethane
ø3.2, ø4, ø6, ø8
Substantial reduction of mounting space.Requires less installation space compared with use of numerous bulkhead unions for panel mounting.
One-touch installation and removal of connector.Numbers of pipes can be connected and disconnected instantly without connection errors, saving substantial labour in installation.
One-touch tubing connection.One-touch fittings substantially cut down man hours for piping.
Plug caseEngagement in the prescribed position can be achieved by fitting both surfaces.
With one-touch fittingTubing of different diameters can be used together.Metric size ø3.2, ø4, ø6, ø8For application requiring copper-free material (Electroless nickel plated)Two types, with 10 and 20 connecting tubing are available.
PackingCompatible with vacuum of -100kPa to 1 MPa
Clamp bolt
Panel mounting bracket (Standardized)Mounting only requires operation on the panel front. No need to make mounting screw holes. (Allows up to 5 mm of panel thickness) Plug connector
Socket connector
Plate
Screw for bracketE type snap ring
Socket casePAT.PEND
3.2468
KDM10-23 -04 -06 -08
No. of connecting
tubing
10
Applicabletubing O.D.
mmModel
3.2468
KDM20-23 -04 -06 -08
No. of connecting
tubing
20
Applicabletubing O.D.
mmModel
KDM10
KDM20
Flame Resistant One-Touch Fittings Series KR
Fitti
ngs
& T
ubin
g
1447FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
For air and water, vacuum or pressure applications
Low disconnecting force (prevents biting)
Flame resistance equivalent to UL-94 standard V-0
ChuckApplicable to soft nylon.Large retaining force.Secure engagement with chuck and large retaining force with collet.
Compatible with a wide range of pressure, from low vacuum to 1.0 MPa.The special shape ensures sealing and reduces resistance of tubing insertion.
Series KR: Black body.Requires little force for removal.Releases the chuck collet to remove the tube as well as to prevent the chuck from biting too deeply into the tubing.
Effective for piping in confined space.The body and thread portion can be rotated. (For positioning)
Packing
Stud
Release button
O-ringBody
Tubing
Prevents releasing of the tubing due to spatter invasion or adhesion.
Cover (Option)
No need of a sealant tape.
With sealant
ColletGuide
PAT.
Series KR: Black body.Series KR-W2: White Body - See Best Pneumatics
Fluid
Max. operating pressure
Proof pressure
Ambient and fluid temperature
Thread
Sealant (Thread portion)
Air, Water Note1)
1.0MPa
3.0MPa
–5 to 60˚C, In case of water: 0 to 60˚C (With no condensation)
JIS B0203 (Taper thread for piping)
JIS B0211, Class 2 (Metric fine thread)
With sealant (Standard)
MountingNut
Note1) Applicable to general industrial water. Consult SMC if using for other fluids. Surge pressure must be under the maximum operating pressure.
Stainless steel specification compatible with corrosive environment.
303 stainless steel used for metal parts.
Suitable for use in CRT production lines for copper free environment,for food processing machine washing to endure water or salt splashes and for use in clean rooms to prevent particle generation resulting from corrosion.
Tube sizes Ø4 - 16mm
Fluid
Max. operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Thread
Sealant (Thread portion)
Air, Water Note1)
1.0MPa
–100kPa
3.0MPa
–5 to 60˚C, In case of water: 0 to 40˚C (With no condensation)
JIS B0203 (Taper thread for piping)
JIS B0211, Class 2 (Metric fine thread)
With / Without sealant Note2)
MountingNut
Note1) Applicable to general industrial water. Consult SMC if using for other fluids. Surge pressure must be under the maximum operating pressure.Note2) Suffix "S" to part number if sealant is desired.
PAT.
ChuckApplicable to nylon and polyurethane.Large retaining force.Secure engagement with chuck and large retaining force with collet.
Compatible with a wide rangeof pressure, from low vacuum to 1.0MPa.The special shape ensures sealing and reduces resistance in tubing insertion.
Requires little force for removal.Releases the chuck collet to remove the tube as well as to prevent the chuck from biting too deeply into the tubing.
Effective for piping in confined space.The body and thread portion can be rotated.
With sealantNote 1) Please avoid using in a vacuum holding application such as a leak tester, since there is leakage. Note 2) When using at 120°C or higher, for an extended period of time, we recommend that an inner sleeve be
used. Note 3) In the event of using polyurethane tubing, we recommend the use of an inner sleeve in cases where the
tubing is strained.Note 4) Special FKM that is resistant even when steam is used.
Specifications
Stainless Steel 316 One-Touch Fittings Series KQG
Fitti
ngs
& T
ubin
g
1459FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Compact piping space.The hose nipple has a large holding force, allowing easy connection and removal.
A wide variety of models is available.Piping in the same direction is possible at different heights.
Hose Nipple, Hose elbow.Hose nipples and hose elbow accept nylon, soft nylon and polyurethane tubing.
Nylon Soft nylon
M5(JIS B0209, Class 2: Metric coarse thread)
1.0MPa
SUS316SUS 304, Aluminium
Polyurethane
ø4/ø2.5ø6/ø4
ø3.18/ø2.18 ø4/ø2.5ø6/ø4
ø3.18/ø2ø4/ø2.5, ø6/ø4
1.5MPa 0.8MPa
Body
Gasket
BarbThe tube allows easy tubing insertion as well as secure tubing holding.
BodyStainless steel 316
BodyStainless steel 316
TubingHose nipples and hose elbow accept nylon, soft nylon and polyurethane tubing.
Cap nutSecure holding is achieved by manual tightening.Easy disconnection of tubing by loosening.Stainless steel 316
GasketSmall tightening torque.Secure sealing.
BarbThe tube allows easy tubing insertion as well as secure tubing holding.
Gasket
Tubing
Small tightening torque.Secure sealing.
Stainless Steel Miniature Fittings
Series M5ModelDescription
Barb fittings for soft tubing
To pipe soft nylon tubing.
Application
To pipepolyurethane tubing.
To pipe soft nylon, polyurethane tubing.
MS-5AU-3
MS-5AU-4
MS-5AU-6
Universal tee for soft tubing
MS-5ATHU-3
MS-5ATHU-4
MS-5ATHU-6
Barb elbow for soft tubing
Hose nipple
MS-5ALHU-3
MS-5ALHU-4
MS-5ALHU-6
To pipe nylon, soft nylon, polyurethane tubing.
MS-5H-4
MS-5H-6
Hose elbow
ModelDescription Application
• To pipe nylon, soft nylon, polyurethane tubing.• Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
Remark(s)
ø3.18/2.18X M5
ø3.18/2 X M5
ø4/2.5 X M5
ø6/4 X M5
ø3.18/2.18 X M5
ø3.18/2 X M5
ø4/2.5 X M5
ø6/4 X M5
ø4/2.5 X M5
ø6/4 X M5
ø4/2.5 X M5
ø6/4 X M5
Material:PVC
MS-5HLH-4
GasketSealant (M5 thread portion)M-5G1
Gasket (H)
M-5GH
Universal nippleBody rotates 360˚ around the stud axis.
MS-5UN
NippleTo connect fittings and equipment or to connect 2 fittings.
MS-5N
Extension fittingFor 3D piping to prevent interference between fittings.
MS-5J
PlugTo plug unused M5 port.MS-5P
BushingConnection from R1/8 piping to M5 fittings.
MS-5B
Universal tee
MS-5UT
Universal elbow Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
MS-5UL
MS-5HLH-6
ø3.18/2.18 X M5
ø3.18/2 X M5
ø4/2.5 X M5
ø6/4 X M5
Material:Nylon 66GF 30%
Only for MS-5ALHU-6, MS-5HLH-4, MS-5HLH-6 and MS-5ATHU-6.
Remark(s)
M5 male X M5 male
PAT
M5 male X M5 female
M5 male X M5 male
R1/8 X M5 female
M5 female X M5 female X M5 male
M5 female X M5 male
To pipe soft nylon tubing.
To pipepolyurethane tubing.
To pipe soft nylon,polyurethane tubing.
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
To pipe soft nylon tubing.
To pipepolyurethane tubing.
To pipe soft nylon,polyurethane tubing.
Body rotates 360˚ around the stud axis. Position can be fixed after alignment.
Series KA Antistatic One-Touch Fittings
Fittings & Tubing
1464
Antistatic One-Touch Fittings
Applicable Tubing
Series KA
Specifications
Features
Applicable tubing O.D.: Metric Size Connecting thread: M, Uni-thread
Air
1.0MPa
–100kPa
3.0MPa
0 to 40˚C
Unithread, screw
JIS B0209, Class 2 (Metric coarse thread)
Gasket
Brass parts are all electroless nickel plated.
104 to 107Ω
Tubing material
Tubing O.D.
Antistatic soft nylon, Antistatic polyurethane
ø3.2, ø4, ø6, ø8, ø10, ø12
Fluid
Max. operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Sealant (Thread portion)
Copper-free specifications
Surface resistance
One-touch collet mechanism.
Compatible with vacuum to 100 kPa of pressure.
Can be used for copper-free applications.
Flame resistant (Equivalent to UL-94 Standards V-0).
Conductive resin is used for the body sealant of fittings
Mounting thread
PackingCompatible with a wide range of pressure, from low vacuum to 1.0 MPa.The special shape ensures sealing and reduces resistance of tubing insertion.
ChuckLarge retaining force.Secure engagement with chuck and large retaining force with collet.
Effective for piping in confined space.The body and thread portion can be rotated. (For positioning)
Requires little force for removal.Releases the chuck collet to remove the tube as well as to prevent the chuck from biting too deeply into the tubing.
ColletGuide
Tubing
Release button (Black)
Body
O-ring
Stud
Gasket
Uni thread
Antistatic One-Touch Fittings Series KA
Fitti
ngs
& T
ubin
g
1465FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Antistatic One-Touch Fittings
KAH Male Connector
3.2
4
6
8
10
12
M5 M6
M6 M5
M6 M5
KAH23-M5 -M6
-U01KAH04-M5
-M6 -U01 -U02
KAH06-M5 -M6
-U01 -U02 -U03KAH08-U01
-U02 -U03KAH10-U01
-U02 -U03 -U04KAH12-U02
-U03 -U04
Most common style used to pipe from female thread in the same direction.
Applicabletubing O.D.
mmConnecting
threadModel
3.2
4
6
8
10
12
M5 M6
M6 M5
M6 M5
KAL23-M5 -M6
-U01KAL04-M5
-M6 -U01 -U02
KAL06-M5 -M6
-U01 -U02 -U03KAL08-U01
-U02 -U03KAL10-U01
-U02 -U03 -U04KAL12-U02
-U03 -U04
Most common style used to pipe from female thread at a right angle.
Applicabletubing O.D.
mm
Connecting thread Model
3.2
4
6
8
10
12
M5 M6
M6 M5
M6 M5
KAT23-M5 -M6
-U01KAT04-M5
-M6 -U01 -U02
KAT06-M5 -M6
-U01 -U02 -U03KAT08-U01
-U02 -U03KAT10-U01
-U02 -U03 -U04KAT12-U02
-U03 -U04
To branch the line from the female thread at 90˚ in each direction.
Applicabletubing O.D.
mm
Connecting thread Model
3.2
4
6
8
10
12
M5 M6
M6 M5
M6 M5
KAY23-M5 -M6
-U01KAY04-M5
-M6 -U01 -U02
KAY06-M5 -M6
-U01 -U02 -U03KAY08-U01
-U02 -U03KAY10-U01
-U02 -U03 -U04KAY12-U02
-U03 -U04
To branch the line from the female thread in the same direction and at 90˚.
1467FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Clean One-Touch Fittings (For Air Blow Applications)
Recommended Applicable Tubing
Series KP
Specifications
Features
Applicable tubing O.D.: Metric Size Connecting thread: R
Particle generation grade
Fluid
Max. operating pressure (20˚C)
Operating vacuum pressure
Proof pressure (20˚C)
Ambient and fluid temperature
Thread
Grade 1Air, Nitrogen gas, Water (Pure water)
1MPa–100kPa
3MPa–5 to 80˚C (With no condensation)JIS B0203 (Taper thread for piping)
Tubing material
Tubing O.D.
Polyolefin: Series TPHSoft polyolefine: Series TPS
ø4, ø6, ø8, ø10, ø12
Completely oil free.Tube sizes 4mm to 12mm avaiable.Liquid contact parts are non-metal.Components are washed, assembled and double packed in a clean room.Compatible with vacuum pressure (-100kPa).
Polyurethane tubing: Series TU, Nylon tubing: Series T, Soft nylon tubing: Series TS also can be used though with lower degree of cleanliness.
Note 1) Refer to the particle generation grade classifications.Note 2) Contact SMC for other types of fluids.Note 3) The max. operating pressure is one at 20˚C.Note 4) When water is used as the operating fluid, do not allow the surge pressure to exceed the max. operating pressure.
Series KP is designed for clean blow and use in washing lines. Consult SMC for use in other applications.
Sealant material: EPDM does not have sufficient resistance to mineral oil and is not suitable for piping of general pneumatic equipment.
Note 1)
Note 2)
Note3)
Particle GenerationGrade Classifications
0.1 0.2Particle Diameter m or less
Aver
age
parti
cle
conc
entra
tion
parti
cles
/ft3
0.3 0.5 1
10-1
100
101
102
103
104
Grade 4
Grade 3
Grade 2
Grade 1Caution
Polyolefin resin
SUS304 stainless steelThe chuck provides a secure bite, while holding force isincreased by the collet.
EPDMHolds the cushion and secures the seal.Suppresses sliding of the seal to prevent generation of particulates.
SUS304stainlesssteel
Polypropylene resin
EPDMSpecial configuration for reliable sealing and low resistance when inserting tube.
SUS304 stainless steelThe body can be rotated to position the piping entry (For positioning purpose).
Releases the chuck collet when tubing is removed. Also prevents the chuck from biting excessively into the tubing.
Release button
Stopper dust check
GuideCollet
Polypropylene resinBody
Polypropylene resinStud
Seal (Oil free)
EPDMO-ring (Oil free)
EPDMCushion (Oil free)
Drive bushing Chuck
Clean tubing
PolypropyleneLight force for removal
PAT.
Series KP Clean One-Touch Fittings
Fittings & Tubing
1468
KPH Male Connector
Clean One-Touch Fittings
KPY Male Run Tee
KPL Male Elbow KPU Union “Y”
KPT Male Branch Tee KPH Straight Union
4
6
8
10
12
KPH04-01 -02KPH06-01
-02KPH08-01
-02KPH10-02
-03KPH12-03
-04
Most common style used to pipe from female thread in the same direction.
Applicabletubing O.D.
mmConnecting
threadModel
4
6
8
10
12
KPL04-01 -02
KPL06-01 -02
KPL08-01 -02
KPL10-02 -03
KPL12-03 -04
Most common style used to pipe from female thread at a right angle.
Applicabletubing O.D.
mmConnecting
threadModel
4
6
8
10
12
KPT04-01 -02
KPT06-01 -02
KPT08-01 -02
KPT10-02 -03
KPT12-03 -04
To branch the line from the female thread at 90 in each direction.
Applicabletubing O.D.
mmConnecting
threadModel
4
6
8
10
12
KPY04-01 -02
KPY06-01 -02
KPY08-01 -02
KPY10-02 -03
KPY12-03 -04
To branch the line from the female thread in the same direction and at 90˚.
Applicabletubing O.D.
mmConnecting
threadModel
4
6
8
10
12
KPU04-01 -02KPU06-01
-02KPU08-01
-02KPU10-02
-03KPU12-03
-04
To branch tubing in the same direction.
Applicabletubing O.D.
mmConnecting
threadModel
4681012
KPH04-00KPH06-00KPH08-00KPH10-00KPH12-00
To connect tubing in the same direction.
Applicable tubing O.D.mm
Model
R1/8R1/4R1/8R1/4R1/8R1/4R1/4R3/8R3/8R1/2
R1/8R1/4R1/8R1/4R1/8R1/4R1/4R3/8R3/8R1/2
R1/8R1/4R1/8R1/4R1/8R1/4R1/4R3/8R3/8R1/2
R1/8R1/4R1/8R1/4R1/8R1/4R1/4R3/8R3/8R1/2
R1/8R1/4R1/8R1/4R1/8R1/4R1/4R3/8R3/8R1/2
Clean One-Touch Fittings Series KP
Fitti
ngs
& T
ubin
g
1469FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
KPL Union Elbow
Clean One-Touch Fittings
KPR Plug In Reducer
4
6
8
10
KPR04-06 -08
KPR06-08 -10
KPR08-10 -12
KPR10-12
To connect to a smaller one-touch fitting.
Applicabletubing O.D.
mmModel
4681012
KPL04-00KPL06-00KPL08-00KPL10-00KPL12-00
To connect tubing at right angles to each other.
Applicable tubing O.D.mm
Model
4681012
KPT04-00KPT06-00KPT08-00KPT10-00KPT12-00
To branch tubing into 2 directions each at 90˚ to the original one.
Applicable tubing O.D.: Metric Size Connecting thread: M, R
Particle generation grade
Fluid
Max. operating pressure (20˚C)
Operating vacuum pressure
Proof pressure (20˚C)
Ambient and fluid temperature
Thread
Grade 1Air
1MPa–100kPa
3MPa–5 to 60˚C (With no condensation)JIS B0203 (Taper thread for piping)
Wide range of port sizes of M5 to 1/2”
Use of Polypropylene for resin parts.
Tube size Ø 4mm - 12mm available.
Low particle generation suitable for clean room application.
Note 1) Refer to the particle generation grading chart. Internal parts are not included in the grading because of greasing on sealant.Note 2) The max. operating pressure is one at 20˚C.
Note 1)
Note 2)
Particle Generation Grading
0.1 0.2Particle Diameter µm or less
Aver
age
parti
cle
conc
entra
tion
parti
cles
/ft3
0.3 0.5 1
10-1
100
101
102
103
104
Grade 4
Grade 3
Grade 2
Grade 1
Recommended Applicable Tubing
Tubing material
Tubing O.D.
Polyurethane: Series 10-Nylon tubing: Series T, Soft nylon tubing: Series T and Series TS soft nylon tubing can also be used through with lower degree of cleanliness.
ø4, ø6, ø8, ø10, ø12
Series KPGStainless steel 304Release button: Light blue
Series KPQBrass (electroless nickel plated)Release button: Light gray
Polypropylene resin
Stainless steel 304
Polypropylene resinNBR
Brass (Electroless nickel plated)
Brass (Electroless nickel plated)
Stainless steel 304
Stainless steel 304
Series KPQ Series KPGModelBodyStudChuckGuide, StopperCollet, Release buttonSeal, O-ring, Bumper
Principal Parts Material
Clean One-Touch Fittings Series KPQ/KPG
Fitti
ngs
& T
ubin
g
1471FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Note 1) Not transparent but translucent owing to the material.
Note 1)
Model
TUS Related Accessories
Soft Polyurethane Tubing Series TUS
Fitti
ngs
& T
ubin
g
1477
FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Wear Resistant Tubing
Series TUZFeatures
Made of special polyurethane.
Sliding motion abration reduction to aprox. 1/3of the TU Series.
Flexible tubing sizes 4mm to 12mm OD.
6 Colour variations
How to Order
TUZ0425 BU 20Tubing model
ModelTUZ0425TUZ0604TUZ0805TUZ1065TUZ1208
O.D. x I.D. (mm) 4 x 2.5 6 x 4 8 x 510 x 6.512 x 8
ColourSymbol
BWR
BUYG
ColourBlackWhiteRedBlue
YellowGreen
Length per rollSymbol20
100
Length20 m roll
100 m roll
Burst Pressure Characteristics Curve and Operating Pressure
Temperature (C)
0–20
4.0
3.0
2.0
1.0
0
Pres
sure
(MPa
)
20 40 60
Burst pressure
Maximum operating pressure
Note 1) The minimum bending radius means the value measured by the method shown in the figure at the right at the temperature of 20C when the tube is bent. The minimum bending radius assumes static piping. If the tube is used in a moving part, provide extra length to the tube. Check the bending radius recommended by the flexible protection tube manufacturer to assure that the tube is used in the flexible protection tube.
Improved maximum operating pressures above 0°C compared to standard polyurethane.
TUH 06 04 B 20Length per roll
Symbol Length20100
20m roll100m roll
Colour indicationSymbol Colour
BWBUN
BlackWhiteBlue
Translucent
Tubing I.D.
Tubing O.D.
Specifications
How to Order
Note 1) Consult SMC regarding other fluids. Water cannot be used because of occurrence of hydrolysis.Note 2) The maximum operating pressure is the value at 20˚C. Refer to the burst pressure characteristics and
operating pressure curve for other temperatures. Abnormal temperature rises due to adiabatic compression can cause tubing to burst.
Note 3) The minimum bending radius is measured at 20˚C based on the method shown in the figure at the left. At higher temperatures, breakage or flattening may occur even with a value larger than the minimum bending radius.
Model O.D. mmI.D. mmModel
O.D. mmI.D. mm
Standard
High pressure
Fluid
Burst pressureOperating temperatureMaterial
Metric sizeTubing
TUH04284
2.8TUH0425
42.5
TUH060464
TUH080585
TUH1065106.5
TUH1208128
TUH06446
4.4
TUH08588
5.8
TUH1073107.3
TUH1288128.8
Black (B)Opal (W)Blue (BU)Translucent (N)
–20m roll –100m
Air Note 1)
0.8MPa Note 2)
1.0MPa Note 2)
Refer to burst pressure characteristics curve.–20 to 60˚CPolyurethane
10 18 24 30 3610 15 20 27 35
Max. operating pressure (20˚C)
Min. bending radius mm
Standard typeHigh pressure typeStandard typeHigh pressure type
Standard type
High pressure type
Burst Pressure Characteristics and Operating Pressure Curve
5
4
3
2
1
0-20 0 20
Operating temperature ˚C
Burs
t pre
ssur
e M
Pa
40 60
Max. operating pressure
5
6
7
4
3
2
1
0-20 0 20
Operating temperature ˚C
Burs
t pre
ssur
e M
Pa
40 60
Max. operating pressure
Standard type
High pressure type
Polyurethane Coil Tubing Series TCU
Fitti
ngs
& T
ubin
g
1479FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Polyurethane Coil Tubing
Series TCU
Coil Tubing
Features
Tubing Size: Metric SizeSpecifications
Model
O.D.
4
6
8
I.D.
1231231
1.5
12
1.512
Max. operating length mNumber of rolls Model
2.5
4
5
colour
Black (B)Black (B)Black (B)Black (B)Black (B)Black (B)Black (B)
TCU0425B-1
1
TCU0425B-2
24
2.5
TCU0425B-3
3
TCU0604B-1
1
Air Note 1)
0.8MPaRefer to burst pressure characteristics curve.
–20 to 60˚CPolyurethane
Black
TCU0604B-2
264
TCU0604B-3
3
TCU0805B-1
185
Note 1) Consult SMC regarding other fluids.Note 2) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid
abnormal temperature rises due to adiabatic compression.
Number of coresTubing O.D. mmTubing I.D. mmFluidMax. operating pressure (20˚C)Burst pressureOperating temperatureMaterialcolour
Burst Pressure Characteristics and Operating Pressure Curve
Note 2)
Single or multi-core option.
For flexible piping applications.
For compact piping.
Series TFU Polyurethane Flat Tubing
Fittings & Tubing
1480
Polyurethane Flat Tubing
Series TFU
10m Roll
Features
Tubing Size: Metric SizeSpecifications
2 or 3 core flat tubing for neat presentation.
For flexible piping applications.
For compact piping.
TFU 04 25 B 2Number of cores
Symbol Number of cores23
23
Colour indicationSymbol Colour
B BlackTubing I.D.
Tubing O.D.
Model
2 3 2 3 2
TFU0425B-2
TFU0425B-3
TFU0604B-2
TFU0604B-3
TFU0805B-2
TFU0805B-3
34
2.5
10
64
Air Note 1)
0.8 MPaRefer to burst pressure characteristics curve.
–20 to 60˚C (With no condensation)Polyurethane
Black1510
85
20
Number of coresTubing O.D. mmTubing I.D. mmFluidMax. operating pressure (20˚C)Burst pressureOperating temperatureMaterialColourMin. bending radius mmTubing length per roll (m)
Note 1) Consult SMC regarding other fluids. Avoid abnormal temperature rises due to adiabatic compression.
–20 to 60˚C, Water: 0 to 60˚C (With no condensation)Flame resistant nylon (Equivalent to UL-94 Standards V-0)
17 19 27 32
Flame resistant tubing(equivalent to UL-94 Standards V-0).
Applicable to general pneumatic and water piping in a spark atmosphere such as in spot welding.
–20m roll –100m on reel
Series TRB FR Double Layer Tubing
Fittings & Tubing
1482
Flame Resistant Double Layer Tubing
Series TRB
Series
Features
Tubing Size: Metric Size
Specifications
Burst Pressure Characteristics and Operating Pressure Curve
How to Order
TRB 10 75 B 100Length per roll
Symbol Length20100
20m roll100m on reel
Colour indication
Tubing I.D.
Tubing O.D.Symbol Colour
BWR
BUYG
BlackWhiteRedBlue
YellowGreen
Flame resistant (equivalent to UL-94 Standards V-0)
Applicable to general pneumatic and water piping in a spark atmosphere such as in spot welding.
Double layer design using flame resistant resin (equivalent to UL-94 Standard V-0) for outer layer.
FluidMax. operating pressure (20˚C)Burst pressure
Air, Water Note 2)
1.0MPaRefer to burst pressure characteristics curve.
Nylon 11PVC (Equivalent to V-0 in UL-94 Standards)
–20 to 60˚C, Water: 0 to 60˚C (With no condensation)
Inner tubing O.D. mmInner tubing I.D. mmOuter layer thickness mm
Min. bending radius mm
Metric sizeTubing
TRB0604641
15 28 35 45
TRB0806861
TRB1075107.51
TRB12091291
Black (B)White (W)Red (R)Blue (BU)Yellow (Y)Green (G)
–20m roll –100m on reel
Note 1)
Operating temperatureInner tubingOuter layer
Note 1) The inner tubing are all black.Note 2) Applicable to general industrial water. Consult SMC for use of other types of fluids. Keep the surge pressure below the maximum operating temperature.Note 3) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid abnormal temperature rises due to adiabatic compression.
Material
Tool to peel off outer layer tubing.
Inner tubingSoft Nylon
Outer layer
FR double layer tubing (Sectional view)
Out
er la
yer c
olou
r
Model
Note 3)
Related Accessories
Tubing Cutter Series TKS
FR Double Layer Polyurethane Tubing Series TRBU
Fitti
ngs
& T
ubin
g
1483FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Flame Resistant Double Layer Polyurethane Tubing
Series TRBU
Series
Features
Tubing Size: Metric Size
Specifications
Burst Pressure Characteristics and Operating Pressure Curve
How to Order
TRBU 10 65 B 100Length per roll
Symbol Length20100
20m roll100m on reel
Colour indication
Tubing I.D.
Tubing O.D.Symbol Colour
BWR
BUYG
BlackWhiteRedBlue
YellowGreen
Flame resistant (equivalent to UL-94 Standards V-0)
Applicable to general pneumatic and water piping in a spark atmosphere such as in spot welding.
Double layer design using flame resistant resin (equivalent to UL-94 Standard V-0) for outer layer.
Inner tubing material: Polyurethane
FluidMax. operating pressure (20˚C)Burst pressure
Air, Water Note 2)
0.8MPaRefer to burst pressure characteristics curve.
PolyurethanePolyolefin resin (Equivalent to V-0 in UL-94 Standards)
–20 to 60˚C, Water: 0 to 40˚C (With no condensation)
Inner tubing O.D. mmInner tubing I.D. mmOuter layer thickness mm
Min. bending radius mm
Metric sizeTubing
TRBU0604641
15 20 27 35
TRBU0805851
TRBU1065106.51
TRBU12081281
Black (B)White (W)Red (R)Blue (BU)Yellow (Y)Green (G)
–20m roll –100m on reel
Note 1)
Operating temperatureInner tubingOuter layer
Note 1) The inner tubing are all black.Note 2) Applicable to general industrial water. Consult SMC for use of other types of fluids. Keep the surge pressure below the maximum operating temperature.Note 3) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid abnormal temperature rises due to adiabatic compression.Note 4) The value at a temperature of 20˚C.
Burst pressure Min. bending radius mm Operating temperature MaterialSurface resistance
Metric size Tubing
TAU3220 3.22
TAU0425 4
2.5
TAU0604 64
TAU0805 85
TAU1065 106.5
TAU1208 128
Black (B)
–20m roll –100m on reel
Length per roll Symbol Length20100
20m roll 100m on reel
Colour indication Symbol Colour
B Black
Tubing I.D.
Tubing O.D.
Refer to burst pressure characteristics curve.
0 to 40˚C Conductive polyurethane
104 to 107
10 10 15 20 27 35
For pneumatic piping system requiring anti static measures.
Flexible tubing
Note 1) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid abnormal temperature rises due to adiabatic compression. Note 2) The value at a temperature of 20˚C.
Note 1)
Note 2)
0.9MPaMax. operatingpressure (20˚C)
How to Order
Antistatic Soft Polyurethane Coil Tubing Series TAS
Fitti
ngs
& T
ubin
g
1485
FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Antistatic Soft Polyurethane Tubing
Series TAS
Series
Features
Specifications
Burst Pressure Characteristics and Operating Pressure Curve
0 to 40˚CConductive polyurethane + flame resistant nylon (equivalent to UL-94 standards V-0)
104 to 107
12 12 15 19 27 32
Note 1) Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Avoid abnormal temperature rises due to adiabatic compression.Note 2) The value at a temperature of 20˚C, with a 10% or less O.D. variable rate.
Note 1)
Note 2)
1.2MPaMax. operating pressure (20˚C)
How to Order
20m Roll 100m on Reel
For pneumatic piping system requiring anti static measures.
Flame resistant tubing(Equivalent to UL-94 Standards V-0)
At a temperature of 20°C, bend the tubing into a U shape. Fix one end and gradually move the other end closer. Measure 2R at the point where the outside diameter's rate of change is 5%.
How to measure the minimum bending radius.
aPM erusserP gnitar ep
O .xaM
Operating Temperature °C
1
0.5
0-20 0 20 40 60 80 100120140160180200
2
3
TH0402
TH0604
TH0425
TH1008/TH1210
TH0806/TH1075/TH1209
Note) The maximum operating pressure varies dependant on the I.D. bore size even if the O.D. is the same.
Fluid
Applicablefittings
Max. operating pressure
Operating temperatureMaterial
One-touch fittings: Series KQ, KJ Insert fittings: Series KFFluoropolymer fittings: Series LQMiniature fittings: Series M, MS (Hose nipple type)
Refer to below “Max. Operating Pressure.”Min. bending radius (mm) 15
Air, Inert gas: -20 to 200° °C (No freezing)
FEP (Fluorinated Ethylene Propylene Resin)
Air, Water Note 1), Inert gasNote 4)
Note 2)
Note 3)
Note 4)
20 35 60 95 100 130
Note 1) When using a fluid in liquid form, the surge pressure must not exceed the maximum operating pressure. A surge pressure higher than the maximum operating pressure can cause breakage of the fittings, or rupture of the tubing.Furthermore, an abnormal temperature increase due to adiabatic compression can also result in ruptured tubing.
Note 2) Do not use in locations where the FEP tubing will move.Be sure to operate under the maximum operating pressure conditions using the lower maximum operating specification of either the tubing or fittings.After long term use or under high temperatures, some fittings leakage may occur due to material deterioration with age. Perform periodic inspections, and if any leakage is detected, replace with a new product immediately.For High Purity Fluoropolymer, refer to the precautions of CAT.ES70-17, "High Purity Fluoropolymer Fittings & Tubing."
Note 3) Minimum bending radius is measured as shown left as representative values.Allow extra length when piping since the tubing may crush if bent more than the min. bending radius.
Note 4) Consult SMC if using any other fluids.
Max. Operating PressureSpecifications
Soft Fluoropolymer Tubing Series TD
Fitti
ngs
& T
ubin
g
1487
FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Soft Fluoropolymer Tubing
Series TDFeatures
Tubing Size: Metric Size
Conforms to Food Sanitation Law.
Material: Denatured PTFEOperating temperature max. 260°C.
Flexibility: Approx. 20% improved.
How to Order
Maximum Operating Pressure
Note 1) When using a liquid fluid, the surge pressure must be under the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to fittings and tubes. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tube bursting.
Note 2) Do not use this product in a manner in which the tube is not fixed.Observe the lesser value of the maximum operating pressure between the tube and fitting.A material change over a long duration or due to high-temperature may cause leakage. Perform periodic
maintenance and replace with a new product immediately when abnormalities are detected.Refer to the “Maintenance” precautions in the TD/TID tubing.For other precautions, see the “Fittings & Tubing” precautions in the “Best Pneumatics catalogue". When using the fluoropolymer fittings, please refer to the precautions in the relevant catalogue CAT. ES70-17.Note 3) The minimum bending radius is the representative value measured as shown below.
• Use a tube above the recommended minimum bending radius.• The tube may be bent if used under the recommended minimum bending radius. Therefore, refer to the refraction value and make sure that the tube is not bent or flattened.
• Please note that the refraction value is not warranted because of the value when 2R is measured by the method shown above on the left if the tube is bent or flattened, etc.
Model/Specifications
Metric size
Insert fitting KF seriesStainless steel 316 insert fitting KFG series
Miniature fittings M, MS series (Hose nipple type)Fluoropolymer fitting LQ2 series
ModelSize
TD0425Tubing O.D. (mm)Tubing I.D. (mm)
Roll
ColorFluid Note 1)
Max. operating temperature (fixed usage)Material
Max. operating pressure (MPa)
Min. bending radius (mm) Note 3)
Applicable fittings Note 2)
10 m20 m
20°C100°C200°C260°C
Recommended radiusRefraction value
42.5
1.6 0.9 0.450.2315 8
1.4 0.7 0.350.2 2516
0.9 0.5 0.250.154531
0.9 0.5 0.250.155535
0.9 0.5 0.250.157541
TD060464
TD080686
Translucent (material colour)Air, Water, Inert gas
Bend the tube into the U-form at a temperature of 20°C. Fix one end and close loop gradually. Measure 2R when the deformed ratio of the tube diameter at bending reaches 5%.
Compatable with max fluid temperature up to 200˚C.
High purity and low particulate generation.
+0.2–0.1
10.1
0.1
Metric sizes (Series TL)
20 40
Tubing modelNominal diameter
Tubing size
O.D.(mm)
Thickness(mm)
Bundle
Straight pipe
ColourApplicable fluidMax. operating pressure (at 20˚C)Burst pressure(at 20˚C) Min. bending radius (mm)Max. operating temperature (Fixed use)
Material
Basicdiameter
Basicdiameter
Tolerance
10 m20 m50 m100 m50 Ft. (16 m)100 Ft. (33 m)2 m
Tolerance
TL0403–
ø4 x ø3
4
0.50.05–––
4.9 MPa
TL0604–
ø6 x ø4
6
–––
6.9 MPa
TL0806–
ø8 x ø6
8
–––
4.7 MPa
65
TL1008–
ø10 x ø8
10
––
3.6MPa
110
TL1210–
ø12 x ø10
12
––
2.9 MPa
1 MPa 0.9MPa 0.7 MPa
160
TL1916–
ø19 x ø16
19
1.50.15––
2.6 MPa
0.6 MPa
Translucent (colour of material)Please refer to the applicable fluid chart.
260˚C
Super PFA
Tubing Model
Eluting fluorine ion amount (ng/g)
Type
Eluting amount
Fluorine ion
0.1 or less
Eluting metal ion amount (ng/cm2)
Type
Eluting amount
Al
4.5
Fe
0.3
Ni
0.2
Na
7.1
Ca
1.3
Length
Symbol102050100
Type
Roll
Length10 m20 m50 m
100 m
Applicable to both metric and inch size
Straight 2 m2S
20TL0604Metric sizes
2R
Note 4) Note 4)
Note 1)
Note 2)
Note 1) • The maximum operating pressure is the value at 20˚C. For other temperatures, calculate from the burst pressure drop coefficient.
Furthermore, an abnormal temperature increase due to adiabatic compression can cause tubing to burst.To operate at a temperature other than 20˚C, the operating pressure must be no more than the value calculated using the equation below: When the value (calculated using the formula below) exceeds 1 MPa, the Max. operating pressure is 1 MPa.(Max. operating pressure) = 1/4 x (burst pressure drop coefficient) x (burst pressure at 20˚C)
• When using a fluid in liquid form, the surge pressure must be no more than the maximum operating pressure.
A surge pressure higher than the maximum operating pressure can cause breakage of the fitting or bursting of the tubing.
Note 2) The minimum bending radius is measured using the method shown in the figure at the right.Note 3) It is connectable with LQ Series (3/4"size). As for other commercial items, there are some cases it is not able to connect due to tolerance of dimensions.
Fixe
d sid
e
At a temperature of 20˚C bend the tubing into a U shape. Then with one side fixed, gradually close the other side and measure 2R at the point where the tubing folds or flattens, etc.
A 15 g piece of fluororesin tubing is cut off, washed in deionized water and immersed in 15 ml of 25% methyl alcohol extract at room temperature for 24 hours. Then the extract is diluted with deionized water to be subjected to a quantitative analysis of fluorine ions.
The interior of the fluororesin tubing is washed with super deionized water. Approximately 20g of super high purity hydrofluoric acid (48%) is measured and injected into the tubing. The interior wall of the tubing is immersed at normal temperature for one week with both ends of the tubing plugged. Then the extract was diluted with super deionized water to be subjected to a quantitative analysis on Al, Fe, Ni, Na and Ca by the stripping method.
+- +- +-
High Purity Fluoropolymer Tubing Series TL
Fitti
ngs
& T
ubin
g
1489FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
The material and fluid compatibility check list provides reference values as a guide only.Note 1) Since static electricity may be generated, implement suitable countermeasures.
• Compatibility is indicated for fluid temperatures of 200˚C or less.• The material and fluid compatibility check list provides reference values as a guide only, therefore we do not guarantee the application to our product.• The data above is based on the information presented by the material manufacturers.• SMC is not responsible for its accuracy and any damage happened because of this data.
Table symbol can be used.
Acetic acid
Acetone
Ammonium fluoride
Ammonium hydroxide
Butyl acetate
Methylne chloride
Hydrochloric acid
Hydrofluoric acid
Hydrogen peroxide
Methanol
Methyl ethyl Ketone
Nitric acid
Phosphoric acid
Caustic potash
Sulfuric acid
Toluene
Xylene
Sodium hydroxide
1.1.1-Trichloroethane
Rhosphorus pentachloride
Isobutyl alcohol
Isopropyl alcohol
Ozone
Ethyl acetate
Deionized water
Nitrogen
Ultrapure water
Tmah
100%
100%
40%
30%
100%
100%
38%
50%
60%
100%
—
70%
86%
85%
100%
—
—
100%
100%
—
—
—
—
—
—
—
—
—
Chemical Compatibility
Note 1)
Note 1)
Note 1)
Note 1)
Note 1)
Material and fluid compatibility check list for high purity fluoropolymer fittings
Burst pressure drop curve1.0
0.8
0.6
0.4
0.2
020 40 60 80 100 120 140 160 180 200 220 240 260
Temperature ˚C
Burs
t pre
ssur
e dr
op c
oeffi
cien
t
Series TPH Clean Tubing: Polyolefin Tubing
Fittings & Tubing
1490
Clean Tubing: Polyolefin Tubing
Series TPH
Series
Features
Tubing Size: Metric Size
Suitable for clean room blowing systems.
6 colour options.
Clean tubing.
TPH 06 04 B 20Length per roll
Symbol Length20
10020m roll100m roll
Colour indicationSymbol Colour
BWR
BUYG
BlackWhiteRedBlue
YellowGreen
Tubing I.D.
Tubing O.D.
How to Order
Burst Pressure Characteristics and Operating Pressure Curve
White (W)Black (B)Red (R)Blue (BU)Yellow (Y)Green (G)
–20m roll –100m roll
15 25 45 551.0MPa 0.7MPa
Note 1) Contact SMC regarding other fluids.Note 2) The maximum operating pressure is the value at 20˚C. Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Abnormal temperature rises due to adiabatic compression can cause tubing to burst.Note 3) The minimum bending radius is measured at 20˚C based on the method shown in the figure at the left. At higher temperatures, breakage or flattening may occur even with a value larger than the minimum bending radius.
Note 2)
Operating temperature ˚C
Max. operating pressure (TPH0425,TPH0604)
TPH0806,TPH1075,TPH1209
Burst pressure
TPH0425,TPH0604
Burst pressure
Max. operating pressure(TPH0806,TPH1075,TPH1209)
Burs
t pre
ssur
e M
Pa
–20 00
1
2
3
4
5
20 40 60 80
Series TP has less resistance to lithium grease and is not suitable for piping of pneumatic equipment using lithium grease.
Caution
Clean Tubing: Soft Polyolefin Tubing Series TPS
Fitti
ngs
& T
ubin
g
1491FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Clean Tubing: Soft Polyolefin Tubing
Series TPS
Series
Features
Tubing Size: Metric Size
Suitable for clean room blowing systems.
6 colour options.
Clean tubing.
Pliable for tight bend radii
TPS 06 04 B 20Length per roll
Symbol Length20100
20m roll100m roll
Colour indicationSymbol Colour
BWR
BUYG
BlackWhiteRedBlue
YellowGreen
Tubing I.D.
Tubing O.D.
How to Order
Burst Pressure Characteristics and Operating Pressure Curve
White (W)Black (B)Red (R)Blue (BU)Yellow (Y)Green (G)
–20m roll –100m roll
10 20 30 400.7MPa
Note 1) Contact SMC regarding other fluids.Note 2) The maximum operating pressure is the value at 20˚C. Refer to the burst pressure characteristics and operating pressure curve for other temperatures. Abnormal temperature rises due to adiabatic compression can cause tubing to burst.Note 3) The minimum bending radius is measured at 20˚C based on the method shown in the figure at the left. At higher temperatures, breakage or flattening may occur even with a value larger than the minimum bending radius.
Note 2)
Series TP has less resistance to lithium grease and is not suitable for piping of pneumatic equipment using lithium grease.
Caution
Operating temperature ˚C
Max. operating pressureBurs
t pre
ssur
e M
Pa
–20 00
1
2
3
4
5
20 40 60 80
Burst pressure
Series TB/TBR/TK Tubing Related Equipment
Fittings & Tubing
1492
Tubing Stand & Reels
Series TB/TBRFeatures
Compact size with a small footprint.
Installation can be easily completed by putting the tubing reels on the stand.
Easy replacement of tubing
One-touch snap fit operation
Locked Unlock condition
Tubing Cutter
Tubing Reels Tubing Stand: TB-2
TK-1 TK-2
Applicable tubing size mm Model
TBR-1TBR-2TBR-3TBR-4
4, 68
1012
Note) Do not use the cutter to cut metal such as wires.
Applicable tubing O.D.: 13mm or less
Applicable tubing O.D.: 18mm or less
TK-3 (Simple type)Applicable tubing O.D.: 12mm or less
Tubing reel
Tubing stand
40060
0750
Movement is easy with attached casters. A reel support is
provided, which can be moved according to the number of reels.
Series TK
Tubing Related Equipment Series TM/TG/TKS
Fitti
ngs
& T
ubin
g
1493FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Multiple Tubing Holder
Series TMFeatures
Double Layer Tubing Stripper
The outer layer of double layer tubing is peeled off easily.
Number of tubing (MAX.) Accessory: Phillips countersunk tapping screwSize: nominal size X length Number of pieces
4
2 X 6
2.6 X 8
3 X 8
Applicable tubing O.D.
Align the cutter with the cutting groove and cut the holder.
Cautionq The multiple tubing holder can be cut apart according to
the number of tubing to be connected.
<Cutting method>
w Cut the multiple tubing holder at a desired position and mount it on the equipment with the attached phillips countersunk tapping screws.
e Align the tube with the holding position and push down to fit it into the holding part.
r Pull up a tubing to remove it from the holder.
How to Use
Model
Tubing Release Tool
Series TG
Double Layer Tubing Stripper
Series TKS
Variations
Series MQR Rotary Joint
Fittings & Tubing
1494
Low Torque Metal Seal Type Rotary Joint
Series MQR
Specifications
How to Order
FeaturesStart-up torque unaffected by supply pressure and temperature fluctuations.Use of metal seals prevents the spool from sticking to the rotating surface even after a long period of non-operation.Operating pressure - 100kPa - 1MPa.Piping ports are aligned in a spiral line for easy piping.
Number of circuits Flange part number2 circuits MQR2-F4 circuits MQR4-F8 circuits MQR8-F12 circuits MQR12-F16 circuits MQR16-F
Model MQR1-M5 MQR2-M5 MQR4-M5 MQR8-M5 MQR12-M5Number of circuits (Number of ports) 1 2 4 8 12Fluid Air / Inert gasSeal structure Metal sealGuide structure Bearing supported Bearing supported at both ends
Port size Male R1/8Female M5
M5
Flow ratecharacteristics
C[dm3/(s.bar)] b Cv0.50 0.40 0.17
Lubrication Not requiredMin. operating pressure –100kPaMax. operating pressure 1.0MPa
–10 to 80°C
Max. start-up rotation torque Note 2) 0.003 N·m or less 0.03 N·m or less 0.05 N·m or less 0.10 N·m or less 0.20 N·m or lessAllowable rotation number 3000 min-1 (r.p.m.) or less Note 3) 2000 min-1 (r.p.m.) or less 1500 min-1 (r.p.m.) or less 900 min-1 (r.p.m.) or less 600 min-1 (r.p.m.) or less
1N or less 15N or less 30N or less 40N or less 50N or less
WeightAllowable axial load
0.025kg 0.16kg 0.39kg 0.76kg 1.26kg
MQR16-M516
0.50 N·m or less200 min-1 (r.p.m.) or less
50N or less
2.80kg
Ambient temperature and operating fluidtemperature Note 1)
Note 1) The temperature 80 °C includes temperature rise during rotation.Note 2) The rotational torque does not change with the supply pressure or with non-use (remains within allowable torque), but it does change with the rotational
speed.Note 3) If using at a speed above 600 min-1 (r.p.m.), ensure rotation is in the direction in which the joint is fastened.Note 4) Rubber / resin couplings are recommended due to their excellent absorption of off center, shocks, and vibrations.
Options/Mounting Bracket
Rotary Joint Series MQR
Fitti
ngs
& T
ubin
g
1495
FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
MQR1-M5
MQR4-M5
MQR2-M5
M4thread length 8
2-M3 thread length 6P.C.D.29
4-M5ø10 counter bore depth 1.5
∗ Flange: MQR2-F (for MQRF2-M5)
∗ 4-ø3.5 mounting hole
∗ 35∗ 29
ø3+0.1 0 depth 10
±3 0.0
5.4
2.862
5.65.3
1
1
2
2
)43( 052
ø15h8
ø35h8(10 from end)
ø15H8
41∗ 5
1 2
(6)
32 2-M3 thread length 8P.C.D.29
∗ Flange: MQR4-F(for MQRF4 - M5)
ø3+0.1 0 depth 10
M5 thread length 10
±0.03
ø20h8ø44h8
(10 from end)
2-M4 thread length 8P.C.D.38
5.5 2-M3 thread length 6P.C.D.38
∗ 4-ø3.5 mounting hole
∗5 4
∗73
207
∗ 5)55(
31
72
1
32
4
5.65.3
6.42 = 3 x 2.82.8 = P
8-M5ø10 counter bore depth 1.5
ø20H8(ø8)
1
2
341
4
4º5
∗ Symbol indicates flange dimensionsDimensions: Standard Type/Flange Type
ssorca htdiW
41 :stalf
ssorca htdiW
7 :stalf
(16.2)M5
ø14
ø7.6
512 43
)8(
R1/8M5
MQR8-M5
M6 thread length 10 4-M3thread length 6P.C.D.43
∗ Flange: MQR8-F(for MQRF8 - M5)
∗ 4-ø4.5 mounting hole
∗50
∗41
ø4.1 0.05 depth 10
0.037
ø49h8 0
0.033ø25h816-M5 ø10 counter bore depth 1.5
378 501
51∗
5
(10 from end)
12
43
56
87
5.75.4
922.8
74.75
P2 .8
ø25H810
12
3
45
6
7
8
462-M4thread length 8P.C.D.43
P54 º
22.5
Series MQR Rotary Joint
Fittings & Tubing
1496
∗ Symbol indicates flange dimensionsDimensions: Standard Type/Flange Type
4-M3thread length 6P.C.D.48
∗ Flange: MQR12-F(for MQRF12-M5)
+0.05ø4.1
±0.038
∗ 4-ø8 counter bore 5.5ø4.5 mounting hole
M6thread length 10
∗55
∗5 4
depth10
24 x M5ø10 counter bore depth1.5
0- 0.033
ø54h8
ø30h8(10 from end)
3021 041
71∗ 7
(10)ø30H8
5.5
139
2.09 = 11 x 2.82.8 = P
12
345
67
89
1011
12
º54 º54
4-M3thread length 8 P.C.D.4851
P=30º
1 23
4
5
6789
10
11
12
MQR12-M5
ø5.1±0.05±0.03depth 8
MQR16-M5
P=225. °
(ø19)5.01 ø40H8
34° 34°
7361
61
10
∗65
∗55
65 ° 65 °
5 .781∗7
5.71
321=51 x 2.8 2.8=P5.73
5.5
ø64h8
ø45h8
16-M5ø10 counter bore 1.5
∗ Flange: MQR16-F(for MQRF16-M5)
1312
54
1615
14
1312
1110 9 8
7654
321
4-ø8 counter bore 5.5ø4.5 mounting hole
M8 thread length 10
8-M3thread length 6P.C.D.54
(10 from end)
1615
14
1110
98
7 6
32
1
16-M5 ø13.5 counter bore 1
4-M3thread length 6P.C.D.58
Blow Gun Series VMG
Fitti
ngs
& T
ubin
g
1497FOR MORE DETAILSSEE OUR SPECIFIC CATALOGUES,PRODUCTS CD´s OR ONLINE INFORMATION
Blow Gun
Series VMG
Specifications
FeaturesSpecial valve design and construction saves energy.
Choice of bottom or top piping.
Selection of nozzles can be added (see KN section).
Threaded or one-touch connection.
Typical pressure loss is less than 1%.
Effective sectional area 30mm². (Without Nozzle)
Provides constant trigger force irrespective of the supply pressure.
How to Order
Blow gun Nozzle
Nil010203041112132122232431323334
Type Nozzle modelWithout nozzleKN-R02-100KN-R02-150KN-R02-200KN-R02-250
Note 1) One piece of H06-02 self-align fitting is attached.
Bottom Piping Top Piping
When a copper extension nozzle is ordered separately, a self-align fitting will also be required for connection. Order one with the above part number in addition to the nozzle.
F03
Series VMG Blow Gun
Fittings & Tubing
1498
Dimensions
Provides constant operational force irrespective of the supply pressure Pressure loss
0 1.0
Conventional product
Ope
ratio
nal f
orce
Supply pressure (MPa)
Larg
eSm
all
Blow Gun VMG
0
0.01
0.02
0.03
0.04
0.05
0 0.2 0.4 0.6 0.8 1 1.2Supply pressure (MPa)
Pres
sure
loss
(MPa
)
∗Male thread nozzle ø2.5
0.005MPa pressure loss at 0.5 MPa
23
23
A
172.
5
34.2
30
147
117.5102
A
30
156
117.5102
S coupler plug mounting
1/4, 3/8
Width across flats 22
1/4, 3/8
Width across flats22
VMG12/Piping entry: Top
VMG11/Piping entry: Bottom
S coupler plug mounting
1/4
1/4
Type Nozzle modelKNS-R02-075-4KNS-R02-090-8KNS-R02-100-4KNS-R02-110-8KNL3-06-150KNL3-06-200KNL6-06-150KNL6-06-200