Office Partitions Assembly Instructions Customer Service 1-800-645-2986 Low-Hi (90˚) 3 - Way Connector Straight Extension Hi-Low (90˚) Right/Left Connector 90˚ Connector Screw Adjust all levelers to approximately 1-1/4” H7 HARDWARE A S S E M B LY • Configurations require the corresponding steps needed for proper assembly. • Attach appropriate brackets or legs on the ends of the panels as needed. • Panels must be level. Level each panel. • Do not attach bolts or brackets into the outermost edge of a panel that will be last in line. • Starter panel should use a corner, 3-way, 4 - w a y, or wall bracket. • Insert bolt cap into unused threaded insert to finish your project. • Level each panel as you go along. H8 H9 H10 H11 Panel Filler Cap Panel Filler Post Hex Bolt Threaded Stud Bolt Cap H13 H14 H15 H16 H17 Toggle Bolt H12 1 Straight Connector 3-way Connector Wall Bracket Right Angle (90˚) Connector 4-way Connector H1 H2 H3 H4 H5 T-Leg H6 WARNING In order to prevent structural failure, instability, tip-over, and/or serious injury, please follow instructions carefully. Do not use hanging shelf or overhead cabinet with panels that have glass. • Use only the instructions, parts and hardware included • Maximum span for connected panels without support is 12 feet • Do not move panels while they are connected together • Maximum span for connected panels using overhead cabinets or shelves without support is 12 feet • Requires 2 people for assembly • Not for outdoor or high humidity areas 12’ 12’ 12’ 12’ O v e r h e a d C a b i n e t s O v e r h e a d S h e l v e s
10
Embed
Office Partitions III · H14 1-800-645-2986 Office Partitions Assembly Instructions H6 H13 (2) (4) P1 E F P2 P3 P4 STEP2 H5 H13 H6 H6 H13 STEP3 STEP4 Fit panel studs into bottom bracket,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Office Partitions
AssemblyInstructions
Customer Service1-800-645-2986
Low-Hi (90 )̊3 - Way Connector Straight Extension
Hi-Low (90 )̊Right/Left Connector 90˚ Connector S c r e w
Adjust all levelers toapproximately 1-1/4”
H7
HARDWARE
A S S E M B LY• Configurations require the correspondingsteps needed for proper assembly.
• Attach appropriate brackets or legs onthe ends of the panels as needed.
• Panels must be level. Level each panel.• Do not attach bolts or brackets into theoutermost edge of a panel that will be lastin line.
• Starter panel should use a corner, 3-way,4 - w a y, or wall bracket.
• Insert bolt cap into unused threadedinsert to finish your project.
• Level each panel as you go along.
H8 H9 H10 H11
Panel Filler Cap Panel Filler PostHex Bolt Threaded Stud Bolt Cap
H13 H14 H15 H16 H17
Toggle Bolt
H12
1
Straight Connector 3-way ConnectorWall BracketRight A n g l e
(90˚) Connector 4-way Connector
H1 H2 H3 H4 H5
T- L e g
H6
WARNINGIn order to prevent structural failure, instability,t i p - o v e r, and/or serious injury, please followi n s t ructions care f u l l y. Do not use hanging shelf oro v e rhead cabinet with panels that have glass.
• Use only the instructions, parts andhardware included
• Maximum span for connectedpanels without support is 12 feet
• Do not move panels while they are connected together• Maximum span for connectedpanels using overhead cabinets orshelves without support is 12 feet
• Requires 2 people for assembly• Not for outdoor or high humidity areas
Note: Hardwareto anchor wallbracket to wall isnot provided.
P1
H1
H13
H1 H13
B
P1
H13
H2
Loosely attach
top bolts
P2
P2
P2
P1
P1
STEP 1
STEP 2
STEP 3
STEP 4
Fit panel
studs into
bottom
bracket,
then loosely
attach to
top bracket
Insert panelfiller caps intopanel fillerpost top andbottom. Insertpost intobottombracket first,then into topbracket. Thentighten allbolts firmlyH16
H15
H2
H13
Foam seal may
need to be trimmed
to fit panel
H1
H13
H14
H2 H13 H14 H15 H16
(2) (6) (2) (2) (1)
P1
Start at
wall and
level
panel
Assembly Instructions
STEP 2
P1
P1
1-800-645-2986
4
Office PartitionsC
D
P2
STEP 2
Loosely attach
top boltsSTEP 1
STEP 3
P1P2
Loosely attach
top bolts
STEP 3
P1
P2P3
Fit panel studs into
bottom bracket, then bolt
and tighten top bracket
Fit panel studs
into bottom
bracket, then
loosely attach
to top bracket
STEP 4
P2P3
H4
H13
H14
H14
H13
H3
H3
H13
I n s e rt panel fillercaps into panelfiller post top andbottom. Insertpost into bottombracket first, theninto top bracket.Then tighten allbolts firm l y