Top Banner
SDI “4-On-The-Floor” Case
36

OCO Biomedical SDI Case

Aug 04, 2015

Download

Business

ocobiomedical
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: OCO Biomedical SDI Case

SDI “4-On-The-Floor” Case

Page 2: OCO Biomedical SDI Case

Pre-Op Panograph

Dr. Paresh Patel

Page 3: OCO Biomedical SDI Case

Patient had a thin ridge. Implants less than 3.0mm were indicated. Notice the facial undercut of the bone

Page 4: OCO Biomedical SDI Case

Blue Mousse used to record normal bite before infiltration

Page 5: OCO Biomedical SDI Case
Page 6: OCO Biomedical SDI Case

Blue bite will be used later to ensure ‘passive fit’ of the denture over the implants and housings

Page 7: OCO Biomedical SDI Case

Endo probe used to sound the bone after infiltration

Page 8: OCO Biomedical SDI Case

Pilot drill taken to just shy of the implant’s length

Page 9: OCO Biomedical SDI Case

Index finger on the lingual side to feel that drill doesn’t perforate the lingual plate

Page 10: OCO Biomedical SDI Case

Periodontal probe used to check drilled pilot hole length

Page 11: OCO Biomedical SDI Case

Perio probe to 11mm. Probe is also used to feel sound bone on all sides

Page 12: OCO Biomedical SDI Case

Thread in implant with the Ultim cap. Angulation was then re-checked visually

Page 13: OCO Biomedical SDI Case
Page 14: OCO Biomedical SDI Case

Thumb knob and driver engaged to thread implant further

Page 15: OCO Biomedical SDI Case

O-Ball head and driving square are finally seated above the tissue which allows the denture to be seated above the tissue.

Page 16: OCO Biomedical SDI Case

Use external irrigation (sterile water) while drilling

Page 17: OCO Biomedical SDI Case

Second implant seated to depth

Page 18: OCO Biomedical SDI Case
Page 19: OCO Biomedical SDI Case

The doctor feels the lingual while the assistant feels the facial to ensure no perforations from the pilot drill

Page 20: OCO Biomedical SDI Case
Page 21: OCO Biomedical SDI Case
Page 22: OCO Biomedical SDI Case
Page 23: OCO Biomedical SDI Case
Page 24: OCO Biomedical SDI Case

The o-ball heads are marked with the Thompson Stick to give a general location of the implant location in the denture. The transfer

marks on the denture indicate where to begin removing acrylic.

Page 25: OCO Biomedical SDI Case
Page 26: OCO Biomedical SDI Case

Axis Crosscut Medium Grit (pear shaped) is used to relieve the denture

Page 27: OCO Biomedical SDI Case
Page 28: OCO Biomedical SDI Case

After the general location is marked, it is best to relieve the denture one cap at a time so that you get a good passive fit

Page 29: OCO Biomedical SDI Case

The transfer mark indicates that the housing is rubbing the denture – need to remove more acrylic to ensure passive fit

Page 30: OCO Biomedical SDI Case

No purple transfer marks. Now we have a passive fit. Denture is ready to reline for chair side pickup of housings

Page 31: OCO Biomedical SDI Case

Housings with O-Rings are engaged onto O-balls

Page 32: OCO Biomedical SDI Case

Reline material is injected into the relieved areas of denture

Page 33: OCO Biomedical SDI Case

The denture is removed. Excess acrylic is removed and any voids are filled in with flowable composite..

Page 34: OCO Biomedical SDI Case

Patient was given1,000 mg of Amoxicillin 1 hour before surgery. Peridex rinse was used one hour before surgery and three days post surgery.

Page 35: OCO Biomedical SDI Case

Post Op Panograph

Dr. Paresh Patel

Page 36: OCO Biomedical SDI Case