Nsk products

NSK

Nsk Electronics , India ©Copyr igh t 2007 ,A l l R igh t Reserved

http://www.nskelectronics.com

NSK

NSK EMBEDDED KITSINTRODUCTION MANUAL

8051 PROGRAMMER - VER 1.0(SERIAL PORT/USB)

Introduction:Simple to use & low cost, yet powerful flash microcontroller programmer for the Atmel 89 series. It will Program, Read andVerify Code Data, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable. This programmer hasintelligent onboard firmware and connects to the serial port. It can be used with any type of computer and requires no specialhardware. All that is needed is a serial communication port which all computers have.All devices have signature bytes thatthe programmer reads to automatically identify the chip. No need to select the device type � just plug it in and go! All devicesalso have a number of lock bits to provide various levels of software and programming protection. These lock bits are fullyprogrammable using this programmer. Lock bits are useful to protect the progam to be read back from microcontroller onlyallowing erase to reprogram the microcontroller.

The programmer connects to a host computer using a standard RS232 serial port. All the programming �intelligence� is builtinto the programmer so you do not need any special hardware to run it. Programmer comes with window based software foreasy programming of the devices supports in Win 9x,2000,Xp,WinMe. This Programmer Supportrs 89C51,89C52,89C5589S51,52,8252

1.3 - Packaging

Your package contains1. 8051 Programmer2. Serial port cable3. User manual4. CD containing software5. 8051 demo board for testing

YOU CAN CONNECT THROUGH USB PORT USING OUR USB TO UART CONTROLLER KIT NO -12.5



NSK

8051 PROGRAMMER - VER 3.1(PARALLEL PORT )

Introduction:

Simple to use & low cost, yet powerful flash microcontroller programmer for the Atmel 89 series. It will Program, Read and Verify CodeData, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable.It can be used with any type of computer and requires no special hardware. All that is needed is a PARALLEL communication port which allcomputers have.The programmer connects to a host computer using a standard Parallel port. All the programming �intelligence� is built into the programmerso you do not need any special hardware to run it. Programmer comes with window based software for easy programming of the devicessupports in Win 9x,2000,Xp,WinMe.Programmer is Built in power supply , The programmer consists of both 40pin&20pin Zip socket for40pin&20pin IC respectively

DEVICES SUPPORTED

AT 89C51,AT89C52,AT89C55,AT89C55WD,AT89C1051,AT89C1051U,AT89C2051,AT89C4051,AT89S51,89S52AT89S53,AT89S8252,AT89C51RC,D87C51,D87C52

i1

1.3 - Packaging

Your package contains1. 8051 Programmer2. PARALLEL port cable3. User manual4. CD containing software5. 8051 demo board for testing



NSK

PIC PROGRAMMER - PIC PROGIntroduction:

Simple to use & low cost, yet powerful flash microcontroller programmer for the PIC series. It will Program, Read and VerifyCode Data, Write Lock Bits, Erase and Blank Check. All fuse and lock bits are programmable. This programmer has intelligentonboard firmware and connects to the serial port. It can be used with any type of computer and requires no special hard-ware. All that is needed is a serial communication port which all computers have.All devices have signature bytes that theprogrammer reads to automatically identify the chip. No need to select the device type � just plug it in and go! All devicesalso have a number of lock bits to provide various levels of software and programming protection. These lock bits are fullyprogrammable using this programmer. Lock bits are useful to protect the progam to be read back from microcontroller onlyallowing erase to reprogram the microcontroller.

The programmer connects to a host computer using a standard RS232 serial port. All the programming �intelligence� is builtinto the programmer so you do not need any special hardware to run it. Programmer comes with window based software foreasy programming of the devices supports in Win 9x,2000,Xp,WinMe.

This Programmer Supportrs i1

12C508,508A,509,509A,671,672,10F200,202,204,206,12CE518,519,673,674,12F675,629,635,683,16C433,54,56,58,61,62A,62B,63,63A,64A,65A,65B,66,67,71,16C72,72A,73A,73B,74A,74B,76,77,84,505,620,620A,621,16C621A,622,622A,711,712,715,716,717,745,765,770,771,16C773,774,781,782,923 ,924,16CE623,624,625,

16F72,73,74,76,77,83,84,84A,88,627,628A,630,648A,676,16F818,819,870,871,872,873,873A,874,874A,876,876A, 877,877A18F242,248,252,258,442,448,452,458,1220,1320,2320,2220.4220,2331,2431,18F4431,4320,4539,6620,6720,8620,8720,6520,8520,2410,2420,2455,2480,2510,2515,2520,2525,2550,2580,2585,2610,2620,2680,4410,4420,4455,4480,4510,4515,4520,4525,4550,4580,4585,4610,4620,4680,

1.3 - Packaging

Your package contains1. PIC Programmer2. Serial port cable3. User manual4. CD containing software5. Demo board for testing

PIC PROG



NSK

USB PIC PROGRAMMER - PIC PLUSIntroduction:

Simple to use & low cost, yet powerful flash microcontroller programmer for the PIC series. It will Program, Read and VerifyCode Data, Write Lock Bits, Erase,and Blank Check,Auto programming mode - this allows you to program chips withouthaving to touch the Windows interface.When active, the software will detect when a chip is inserted into the socket andautomatically commence the program/verify process.Once the chip is programmed, the software will wait until the next chipis inserted before programming continues.All fuse and lock bits are programmable. This programmer has intelligent onboard firmware and connects to the USB portAs a virtual COM prot . It can be used with any type of computer and requires no special hardware. All that is needed is aUSB communication port which all computers have.All devices have signature bytes that the programmer reads to automati-cally identify the chip. No need to select the device type � just plug it in and go! All devices also have a number of lock bits toprovide various levels of software and programming protection. These lock bits are fully programmable using this program-mer. Lock bits are useful to protect the progam to be read back from microcontroller only allowing erase to reprogram themicrocontroller.

The programmer connects to a host computer using a standard USB port. All the programming �intelligence� is built into theprogrammer so you do not need any special hardware to run it. Programmer comes with window based software for easyprogramming of the devices supports in Win 9x,2000,Xp,WinMe.

This Programmer Supportrs

12C508, 12C508A, 12C509, 12C509A,12C671, 12C672, 12CE673, 12CE674,12F629,12F675,16C505,16C554,16C558,16C61,16C62,16C62A,16C62B

16C63,16C63A,16C64,16C64A,16C65,16C65A,16C65B,16C66, 16C66A,16C67, 16C620,16C620A,16C622,16C622A,16C71,16C71A,16C72,16C72A,16C73,16C73A,16C74,16C74A

16C71,16C71A,16C72,16C72A,16C73,16C73A,16C74,16C74A,16C74B,16C76,16C77,16C710,16C711,16C712,16C716,16C745,16C765,16C773,16C774,16C83,16C84,16F627,16F627A,16F628

16F628A,16F630,16F648A,16F676,16F,72,73,16F74,16F76,16F77,16F737,16F747,16F767,16F777,16F83,16F84,16F84A,16F87,16F88,16F818,16F819,16F870,16F871,16F872,16F873,16F873A

16F874,16F874A,16F876,16F876A,16F877,16F877A,18F242,18F248,18F252,18F258,18F442,18F448,18F452,18F458,18F1220,18F1320,18F2220,18F2320,18F4220,18F4320,2550,4550

1.3 - Packaging

Your package contains1. Programmer2. USB port cable3. User manual4. CD containing software5. Demo board for testing



NSK

What is MPLAB ICD 2?

The MPLAB ICD 2 is a low-cost in-circuit debugger (ICD) and in-circuit serial programmer(ICSP). MPLAB ICD 2 is intended to be used as an evaluation, debugging and programming aidIn a laboratory environment. The MPLAB ICD 2 offers these features:

· Real-time and single-step code execution· Breakpoints, Register and Variable Watch/Modify· In-circuit debugging· Target Vdd monitor· Diagnostic LEDs· MPLAB IDE user interface· RS-232 serial interface to a host PC

How MPLAB ICD 2 Helps You

The MPLAB ICD 2 allows you to:

· Debug your source code in your own application· Debug your hardware in real-time· Program a supported device using Microchip�s ICSP protocol through RJ 11

cable supplied with this kit

MPLAB ICD2 PIC PROGRAMMER & DEBUGGER

1.3 - Packaging

Your package contains1. PIC ICD2 Programmer2. Serial port cable3. User manual4. CD containing software5. PIC demo board for testing with RJ11 Socket6. RJ 11 cable crimped on both sides



NSK

AVR PROG ISP PROGRAMMER - USB1. General description

‘ AVR PROG’ support major chips From Atmel Avr Series For programming that are flash program-mable microcontrollers that supports serial programming of devices. Flash microcontroller can be erasedand re-written as many times as possible. Flexibility to reprogram number of times and its low costmake it ideal for use in a wide areas of applications.This product is a combination of intelligent hardwareand software Inside the Chip that understands a protocol received from computer through USB port .On computer side software called ‘AVR PROG ’ is started that identifies the hardware and the chipinserted. Program for the target microcontroller can be now either read back or sent as Intel format HEXfile. Support locking of devices to prevent reading back of programmed chip. After locking the chip canstill be erased and used again for loading new programs.

2. Features

�� Support major AVR devices�� Lock of programs in chip supported to prevent program copying�� Adapter Board with 2 ZIF socket For programming�� Auto Erase before writing and Auto Verify after writing�� Informative status bar and access to latest programmed file�� Simple and Easy to use

3. Specifications

Dimensions: 180mm x 100mmPower Supply - USB POWEREDInterface: USBData Speed: 9600 bps, 8 bits, no parity, 1 stop, no flow controlFile format: Intel 8-bit HEXProgram Sockets: ISP O/P ADAPTER FOR PROGRAMMINGSoftware: Works on Windows 95, 98, Me, 2000, NT, XP

SUPPORTED DEVICES AVR STUDIO >AVR PROG VER 1.40

Nsk Electronics , India ©Copyright 2007,All Right Reservedhttp://www.nskelectronics.com

AVR PROGAVR PROGAVR PROGAVR PROGAVR PROGNSK

AT90S8534,8544,1200,2313,2323,2333AT90S2343,4414,4433,4434,8515,8535ATMEGA103,128,16,161,163,169,32,ATMEGA 603,64,8,83,8515, 8535,

AT TINY 12,15,19,26,28

SUPPORTED DEVICES > AVR OSP II >AVR PROG 911

AT90S1200,2313,2323,2343,4414,4433,4434,8515,8535, ATMEGA103,128,1280,1281,16,161,162,163,165,168,169, ATMEGA 2560,2561,32,323,325,3250,329,3290,406,48,64 ATMEGA 640,644,645,6450,649,6490,8,8515,8535,88 ATTINY 11,12,13,15,22,2323,25,26,261,28,44,45,461,84,85,86 AT90CAN128,32,64 - AT90PWM2,3

Introduction and Features:

� The CPLD Development kit based on Xilinx XC9572XL is a low costevaluation platform for training, testing and developing designsbased on the Xilinx 9500XL family of CPLD.

� The board contains the 1600 gate, 72 macro cells, 100 Pin XC9572XLCPLD with 72 user I/O�s.

� An on-board power supply includes 3.3V regulator, which regulatesVcc internal & Vcc I/O for the CPLD.

� A 40 MHz Crystal Oscillator provides clock source that is directlyconnected to GCK1 clock input on the 9572XL device.

� All user I/O pins are brought out of the 9572XL device.� Peripheral interfaces like LEDs, 7 Segment Displays, Key Switches&Buzzer are provided on board.

� Separate Jumper settings have been provided for accessing the I/Osfor other external applications.

� A built-in JTAG programmer board is also available for programmingthe XC9572XL.

� The HDL code can easily be implemented using the Webpack softwareavailable on the Xilinx Website.

� Datasheets are provided in the CD-ROM accompanying the Kit and asoftcopy of the user manual is also included in the CD as well.

CPLD TRAINER KITXilinx XC9572XL

Packaging

Your package contains1. CPLD kit2. JTAG Parallel port cable3. User manual4. CD containing software (XILINX ISE webpack)



NSK

SEEPROM PROGRAMMER

Introduction

Serial eeproms are finding more and more use in electronic devices these days.These small 8 pin devices offer non-volatile data storage and require minimal I/Olines to connect to them. This makes them ideal in many microcontroller basedapplications.

The programmer connects to the PC Serial port and is controlled by driver softwarerunning on the PC. The software is Windows based will run under Windows9X,2000&XP

EEPROMS SUPPORTED

I(2)C EEPROM SDA252624C01A SDA254624C02 SDA258624C04 SDA350624C08 SDA351624C16 SDA352624C32 MICROWIRE EEPROM

24C64/65 (Atmel) 93C06,93C14,93C46,93C57,93C56,93C66,93C76.93C86AT24C128 (Atmel)AT24C256 (Atmel)AT24C512 (Atmel) M24C128 (Microchip)M24C256 (Microchip)24C515 (Microchip) , SDA2506 ,2516,



NSK

ARM DEVOLOPMENT KIT (LPC2129)ON BOARD ISP &JTAG

1. Board Features:1. LPC 2129 Single-chip 16/32-bit microcontrollers 256KB Flash/128KB RAM2. 4 Channel 10-bit ADC3. 7-Segment LED Display(Multiplexed x4)4. 2 CAN Ports with 2CAN TransRecivers5. A Serial Port for ISP6. An RS232 Serial Port7. On Board JTAG Wiggler for Debugging8. DC Power Supply Connector(12v Ac or Dc)9. Optional USB Socket for Power Supply10. LCD display 2linex16Character11. 24Cxx I2C EEPROM12. 8 LED array13. Matrix Key Pad14. 4 Intruupt Switches15. Buzzer

1.2 Package Contents:

1. ARM Starter evaluation board2. Serial port Cable3. ARM Starter Kit CD4. Parralel port Cable5. Burg connectors 20 Nos



NSK

Introduction:Our Devolopment Board are made with full effort to make projects without soldering& contacts.40 pin Zip socket is provided so as to make easy to remove chips withoutDamages.All the I/O�s are routed to Burg connectors .For each Section burg connectersare given , For Example If you want to use 1 led to connect to port 1,Just connect usingBurg connector form P1.1 to LED array ,So all the I/O�s are fully isolated from the I/Osections (for testing 89c2051 use 20 pin Adapter )

Board Features:1. On board Regaulated Power supply2. Input Power supply - 12v AC or DC3. A 7-Segment LED Display(Multiplexed x4)4. An RS232 Serial Port5. LCD display(optional)6. 24Cxx I2C EEPROM7. RTC DS 13028. Matrix Key Pad9. 4 Intruupt Switches10. Output 5v,12v,GND11. 8 LED array12. ULN 2003 high current driver

1.2 Package Contents:1. 8051 evaluation board2. CD containing(Softwares & Example Programs)3. Burg Connectors 20 Nos

8051 DEVOLOPMENT BOARD



NSK



NSK

The DT125R series RFID Proximity OEM Reader Module has a built-in antenna in minimized form factor.It is designed to work on the industrystandard carrier frequency of 125 kHz.

This LF reader module with an internal or an external antenna facilitates communication with Read-Onlytransponders�type UNIQUE or TK5530 via the air interface. The tag data is sent to the host systemsvia thewired communication interface with a protocol selected from the modulepinout.

The LF DT125R module is best suited for applications in Access Control,Time and Attendance, AssetManagement, Handheld Readers,Immobilizers, and other RFID enabled applications.

RFID Reader Introduction:

Features

! Selectable UART or Wigand26! Plug-and-Play, needs +5V to become a reader! No repeat reads! LED/Beeper indicates tag reading operation! Excellent read performance without an external circuit! Compact size and cost-effective! A very efficient module for portable readers.

GSM/GPRS Modem Introduction:

Introduction

This document describes the hardware interface of the SIMCOM SIM300 module thatconnects to the specific application and the air interface. As SIM300 can be integratedwith a wide range of applications, all functional components of SIM300 are described ingreat detail.

Product conceptDesigned for global market, SIM300 is a Tri-band GSM/GPRS engine that works onfrequencies EGSM 900 MHz, DCS 1800 MHz and PCS 1900 MHz. SIM300 features GPRSmulti-slot class 10/ class 8 (optional) and supports the GPRS coding schemes CS-1, CS-2, CS-3 and CS-4.

SIM card interfaceYou can use AT Command to get information in SIM card.The SIM interface supports the functionality of the GSM Phase 1 specification and alsosupports the functionality of the new GSM Phase 2+ specification for FAST 64 kbps SIM(intended for use with a SIM application Tool-kit).Both 1.8V and 3.0V SIM Cards aresupported.The SIM interface is powered from an internal regulator in the modulehaving nominal voltage 2.8V. All pins reset as outputs driving low. Logic levels are asdescribed in table

PIC DEVOLOPMENT BOARD

Introduction:Our Devolopment Board are made with full effort to make projects without soldering,losecontacts.40 pin Zip socket is provided so it make easy to remove chips without Damages.All the I/O�s are routed to Burg connectors .For each Section burg connecters are given ,For Example If you want to use 1 led to connect to port 1,Just connect using Burg connec-tor form P1.1 to LED array ,So all the I/O�s are fully isolated from the I/O sectionsRJ-11 Socket is provided for in circuit serial programming through our PIC programmers

( FOR TESTING 8,18,28 PIN CHIPS USE ADAPTERS )

Board Features:1. On board Regaulated Power supply2. Input Power supply - 12v AC or DC3. A 7-Segment LED Display(Multiplexed x4)4. An RS232 Serial Port5. LCD display 2linex16Character6. 24Cxx I2C EEPROM ,ULN 2003 high current driver7. RTC DS 13028. Matrix Key Pad9. 4 Intruupt Switches10. Output 5v,12v,GND

Package Contents:1. 8051 evaluation board2. CD containing(Softwares,Example Programs)3. Burg Connectors 20 Nos



NSK

I/O INTERFACE BOARDS12.1 - 4X4 MATRIX KEYPAD 12.2 - MULTIPLEXED7 SEG DISPLAY

(com cathode)

12.3 - AC SOLID SATAERELAY(O/P Load-10 Amps) I/P - 5-12V

12.4 - DC SOLID SATAE RELAY& STEPPER MOTER DRIVE

(O/P Load- 5 Amps) I/P - 5-12V

12.5 - USB TO UART CONVERTERWITH RX&TX O/P&RS-232 LEVEL O/P

12.6- AT89C2051 DEMO BAORD WITHULN 2003 (CAN BE USED FOR STEPPERMOTOR DRIVES UPTO 0.5 A



NSK

12.7 - 8 CHANNEL RELAY CONTROL BOARDwith Power Supply & ULN 2003 I/P

12.8- LCD DISPLAY INTERFACED BOARD WITH 8 O/PHIGH CURRENT DRIVER USING ULN 2003 ,8 I/P

& RS -232 CONVERTER

12.9 Embedded Power Supply +5,-5,+12,-12Variable output from 0 - 24volts

Input Voltage 12-0-12

Introduction: MINI PLC

The Mini PLC is fully isolated with opto couplers Inputs may be from 5v to 12 volts(under request 24v) . the Outputs will be 12 or 5 VDC (100 MA)This board is very useful for mini Automation .Regulated power supply is Built in



NSK

13- STEPPER MOTOR DRIVERIntroduction:

The A/D Stepper Motor Controller IC1 generates four phase drive signalsfor two phase bipolar and four phase unipolar step motors in microcontrollercontrolled applications. The motor can be driven in half step, normal andwawe drive modes and on-chip PWM chopper circuits permit switchmodecontrol of the current in the windings. A feature of this device is that itrequires only clock,direction and mode input signals. Since the phase aregenerated internally the burden on the microcontroler and the programmeris greatly reduced. IC2 is a monolithic bridge high current driver

Specifications:

Input Power Required : 24V DC / 2AMax Power Dissipation : 50 WattsDrive Type : Bipolar Chopper DriveChop Frequency : 20 Khz Min(Above Audiable Range)Output Device Type : Integrated Monilithitic CircuitPhases : Two PhaseOutput Current : 0.5 to 2Amps By 0.5A incrementsCurrent Setting : Dip SwitchOutput Resolution : Full Step @ 200 PPR

Half Step @ 400 PPRPulse Input : TTL Level

MIn Rise Time: 1 MicrosecondMIn Fall Time : 1 MicrosecondSignal Active : From Low to High Transition

All other Inputs : TTL level sinking typeHome Output Type : Open cpllector outputMin phase inductance : 0.5 MHOperating Temparature : 0 to 50 c



NSK

Cont act information

For software Downloads &additional information, please visit http://www.nskelectronics.comFor sales office addresses, send e-mail to: [email protected]

NSK ElectronicsNo 66/3 , Sabari ComplexS.P. Road , Bangalore - 560 002Karnataka , India

PH NO : 91- 080 - 41575115 , 22892194Mobile : 09945263589,09740374373



NSK

Nsk products

Technology

programmer ver

programmer supportrs

programmer supportrs

number of lock bits

serial communication

serial port cable

usb port

standard rs232 serial