Shank / Water Fittings DPL714 877.963.4966 • dixonvalve.com 278 G King Combination Nipples NPT threaded end with knurled wrench grip knurled wrench grip NPT threaded end no knurl Applications: • Recommended for low-pressure discharge and suction service for compatible liquids. Sizes 1¼" and above are not for compressible products such as air or nitrogen. • King Combination Nipples are not recommended for steam. • The working pressure may vary with the construction of the hose, the type of clamping system used and the application. Consult the factory for recommendations. • In accordance with the Association for Rubber Products Manufacturers (ARPM) bulletin for oil suction and discharge hose, a coupled length of hose in any size, should be tested to 1½ times the working pressure and held for fifteen minutes without leaking or coupling movement. For additional information and detailed instruction on testing procedures, see the Association for Rubber Products Manufacturers (ARPM) handbook. Size Opt Qty Unplated Steel Plated Steel Brass Aluminum Part # Price/E Part # Price/E Part # Price/E Part # Price/E ½" 50 ST1 $4.60 STC1 $4.95 BST1 $20.40 AST1 $19.85 ¾" 50 ST5 5.35 STC5 5.45 BST5 30.90 AST5 15.15 1" 50 ST10 6.80 STC10 7.30 BST10 32.25 AST10 18.15 1¼" 50 ST15 9.35 STC15 10.05 --- --- --- --- 1½" 50 ST20 9.65 STC20 10.30 --- --- --- --- 2" 25 ST25 11.95 STC25 12.60 --- --- --- --- Size Opt Qty Unplated Steel Plated Steel Brass Aluminum Part # Price/E Part # Price/E Part # Price/E Part # Price/E 1¼" 50 --- --- --- --- BST15 $35.40 AST15 $17.15 1½" 50 --- --- --- --- BST20 44.75 AST20 17.30 2" 25 --- --- --- --- BST25 66.70 AST25 19.55 2½" 10 ST30 $19.75 STC30 $21.70 BST30 106.60 AST30 59.00 3" 10 ST35 23.10 STC35 26.70 BST35 145.00 AST35 47.00 4" 4 ST40 36.40 STC40 40.00 BST40 283.90 AST40 72.60 5" 4 ST50 84.10 STC50 89.25 --- --- AST50 164.85 6" 2 ST60 93.10 STC60 105.00 --- --- AST60 178.50 8" 2 ST80 161.75 STC80 202.80 --- --- --- --- 10" 1 ST100 267.50 STC100 337.50 --- --- --- --- 12" 1 ST120 400.00 STC120 480.00 --- --- --- --- Size Opt Qty 316 Stainless Steel Hastelloy Part # Price/E Part # Price/E ½" 50 RST1 1 $21.10 --- --- ¾" 50 RST5 1 21.15 --- --- 1" 50 RST10 21.25 --- --- 1¼" 50 RST15 27.10 --- --- 1½" 50 RST20 32.60 --- --- 2" 25 RST25 45.00 HST25 $780.00 2½" 10 RST30 82.75 --- --- 3" 10 RST35 117.40 HST35 1450.00 4" 4 RST40 184.20 --- --- 5" 4 RST50 405.00 --- --- 6" 4 RST60 508.20 --- --- 8" 2 RST80 975.00 --- --- 1 made from investment casting no knurl brass no knurl stainless www.comoso.com
30
Embed
NPT threaded end with knurled wrench grip NPT threaded end ... · Shank Water Fittings 278 877.963.4966 • dixonvalve.com DPL714 DPL714 877.963.4966 • dixonvalve.com 279 G King
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Applications:• Recommended for low-pressure discharge and suction service for compatible liquids. Sizes 1¼" and above are not for compressible products such as air or nitrogen.• King Combination Nipples are not recommended for steam.• The working pressure may vary with the construction of the hose, the type of clamping system used and the application.
Consult the factory for recommendations.• In accordance with the Association for Rubber Products Manufacturers (ARPM) bulletin for oil suction and discharge hose,
a coupled length of hose in any size, should be tested to 1½ times the working pressure and held for fifteen minutes without leaking or coupling movement. For additional information and detailed instruction on testing procedures, see the Association for Rubber Products Manufacturers (ARPM) handbook.
Size OptQty
Unplated Steel Plated Steel Brass AluminumPart # Price/E Part # Price/E Part # Price/E Part # Price/E
Applications:• Combination nipples are recommended for low-pressure discharge and suction service for compatible liquids. Sizes 1¼" and above are not for compressible products such as air or nitrogen.• Global King Combination Nipples are not recommended for steam.• The working pressure may vary with the construction of the hose, the type of clamping system used and the application.
Consult the factory for recommendations.• In accordance with the Association for Rubber Products Manufacturers (ARPM) bulletin for oil suction and discharge hose,
a coupled length of hose in any size, should be tested to 1½ times the working pressure and held for fifteen minutes without leaking or coupling movement. For additional information and detailed instruction on testing procedures, see the Association for Rubber Products Manufacturers (ARPM) handbook.
The notched system allows you to better manage your inventories. You can stock one stem and two ferrules, and cover the same hose range with less inventory. You must purchase a fitting and the matching ferrule to create an assembly.Features:• For hose outside diameters of 2-4/64" and below, couplings are crimp only.• For hose outside diameters of 2-5/64" and above, couplings can be crimped or swaged.• See page 69 for cam and groove style notched NOS fittings.
PF Shank King Combination NipplesApplication:• This shank design was developed specifically for chemical transport hoses having Crosslinked Polyethylene (XLPE) or Ultra
High Molecular Weight Polyethylene (UHMW) tubes, where shank retention can be a problem when using conventional band clamps.
Features:• PF shank King Combination nipples have the same shank pattern as found on the PF style cam and groove fittings sold on
page 66. • recommended for discharge and suction service• Not intended for compressed air• working pressure is given at 70°F maximum
• The working pressure may vary with the construction of the hose, the type of clamping system used and the application. Consult the factory for recommendations.
NPT Threaded end
Tuff-Lite King Combination Nipples
Note: Beveled ends for welding are also available. Contact Dixon for further information.
Size WorkingPSI
Plated Steel 316 Stainless SteelPart # Price/E Part # Price/E
Dixon stems and ferrules are specifically designed to be used together as a coupling system.Due to differences in dimensions and tolerances for safety reasons,
do not use other manufacturer's stems or ferrules with Dixon Holedall products.
150# ASA flange x hose shank
Size
Steel 316 Stainless Steel
Standard Designed for crimp-style sleeves or ferrules Standard Designed for crimp-style
sleeves or ferrulesPart # Price/E Part # Price/E Part # Price/E Part # Price/E
Features:• Stems are for use with lap joint flanges on page 714.• When used with an appropriate notched ferrule, these fittings can be swaged or crimped onto
hose providing improved shank retention.• When used with double bolt or band clamps, notched turn back nipples provide shank
retention similar to that of the King turned back nipples.• The stem can be removed from a damaged hose by cutting away the ferrule without
necessarily damaging the fitting. After inspection to determine its suitability for reuse, it can reinstalled into another hose by using a new ferrule.
All Super King long shank couplings will accept 3 band clamps.Replacement FKM (KVW) gaskets are available on page 291. PTFE gaskets are available on page 750.
NPSM Female Coupling
KLW leather gaskets standard PTFE gaskets standard
• They are not for compressible products such as air, nitrogen or steam.• The working pressure may vary with the construction of the hose, the type of clamping system used and the application.
Consult Dixon for recommendations.• In accordance with the ARPM bulletin for oil suction and discharge hose, a coupled length of hose in any size, should be
tested to 1½ times the working pressure and held for fifteen minutes without leaking or coupling movement. For additional information and detailed instruction on testing procedures, see the Association for Rubber Products Manufacturer's (ARPM) handbook or visit ARPMINC.com.
• They are not for compressible products such as air, nitrogen or steam.• The working pressure may vary with the construction of the hose, the type of clamping system used and the application.
Consult the factory for recommendations.• In accordance with the ARPM bulletin for oil suction and discharge hose, a coupled length of hose in any size, should be
tested to 1½ times the working pressure and held for fifteen minutes without leaking or coupling movement. For additional information and detailed instruction on testing procedures, see the Association for Rubber Products Manufacturer's (ARPM) handbook or visit ARPMINC.com.
Features:• brass with NBR seat and stainless steel strainer• soft seat for bubble tight shutoff, spring loaded for fast seating action• flow profile designed to minimize head loss• temperature range: 10°F to 210°F (-10°C to 100°C)• cracking pressure: 0.50 PSI• pressure rating: 1½"-2" 400 PSI WOG, 3"-4" 175 PSI WOG• Underwriters approved
Type A male with 150 ASA flangeType A female with 150 ASA flange with gasket
Type A male with hose shankType A female with hose shank with gasket
1 12" supplied with M20412 lever assist bar
Type A male x female 90° elbow with gasket
Application:• Used primarily on irrigation and suction lines.Features:• hot dipped, galvanized • has a double pin locking lever for smooth closing action.• Type A (Agri-Lock style) locks on the female side. • Type B (Bauer style) locks on the male side.
• Each coupler is equipped with a safety pin to prevent accidental openings.
(Agri-Lock style)Type A
Size Galvanized SteelPart # Price/E
10" MC22210 $891.2512" MC22212 1216.80
Size Galvanized SteelPart # Price/E
10" FC22310 $875.5012" FC22312 1 1257.00
Size Galvanized SteelPart # Price/E
10" FC21210 $346.2512" FC21212 1 630.00
Size Galvanized SteelPart # Price/E
10" MC21110 $352.8012" MC21112 551.50
Size Galvanized SteelPart # Price/E
10" EL21510-90 $806.2512" EL21512-90 1 1265.75
• These fittings are not recommended for chemicals or any hazardous type materials where the possibility of leakage would result in health or environmental concerns. Consult the factory for recommendations.
Application:• Suitable for water, potable liquids and neutral gas applications: including water filtration, water coolers, coffee machines and
beverage dispensers.Features:• EPDM seal secures connection with larger surface area than
standard O-rings• engineered polymer allows superior mechanical strength
and chemical resistance• full stainless gripping ring eliminates the need for locking
clips• release button protects and supports tubing• FDA compliant• meets California and Vermont <0.25% lead requirements• NSF-51 listed for contact with food• NSF-61 list C-Hot rated• in compliance with the following standards:
Specifications:• working pressure: ¼" 230 PSI from 35°F to 100°F 150 PSI at 150°F 60 PSI at 200°F ⅜" 190 PSI from 35°F to 100°F 100 PSI at 150°F 60 PSI at 200°F ½" 160 PSI from 35°F to 100°F 100 PSI at 150°F 60 PSI at 200°F• maximum torque values for NPTF threads: ⅛" and ¼" 1.0 ft. lbs. / 1.5Nm ⅜" and ½" 2.2 ft. lbs. / 3.0Nm
TrueSeal™ Ball ValvesApplication:These corrosion resistant, all-plastic designed ball valves are ideal for water filtration units, coffee and beverage machines and a wide variety of other fluid applications.Features:• EPDM seal secures connection with larger surface area than
standard O-rings• full flow self-cleaning ball• high-temperature, scale resistant Polysulfone ball• glass-reinforced Polypropylene body• FDA compliant• NSF-51 listed for contact with food
Specifications:• temperature range: 0°F to 225°F (-18°C to 107°C)• O-ring seal material: EPDM• maximum operating pressure: 150 PSI • Burst pressure 600 PSI• Actual working pressures will be lower at elevated
TrueSeal™ Ball ValvesValve Male Connectors Valve Female Connectors
Valve Union Connectors
tube to tube
Valve Elbow Unions
TrueSeal™ Check Valves
tube to tube
Valve Plug-in Elbow Unions
tube to plug-in
Application:Push-to connect check valves ensure protection against reversal of flow. The valves have an arrow molded into the body to indicate the direction of flow. Valves are designed for connection with either thermoplastic or soft metal tubing and are intended for use with liquids only.Features:• body material: acetal• O-ring: EPDM• metal grip edge: 300 stainless steel
• NSF-51 listed• maximum operating pressure: 150 PSI (dependent on tubing
used)• temperature range: 34°F to 150°F (1°C to 65°C)• cracking pressure: 1/3 PSI
Part # Price/E½" x ½" U008 $17.60¾" x ¾" U016 19.401" x 1" U020 43.00
Tube SizeForged Brass
Part # Price/E¾" x ½" U058 $20.751" x ¾" U060 52.50
Tube Size FemaleNPT
Forged BrassPart # Price/E
½" ½" U072 $14.70¾" ¾" U088 16.751" 1" U094 33.75
Tube Size MaleNPT
Forged BrassPart # Price/E
½" ½" U120 $14.20¾" ¾" U134 16.001" 1" U140 35.25
Tube Size Female NPTForged Brass
Part # Price/E½" ¾" U068 $17.60
Tube Size Male NPTForged Brass
Part # Price/E½" ¾" U116 $17.10
Applications:• for water, dry, clean air or 100% glycol solutions only • connects copper, CPVC, and PEX pipe in any combination• approved for use underground and behind walls without
access panelsFeatures:• no soldering, clamps, unions or glue needed• pressure rating: 200 PSI at 200°F• integral tube liner for PEX installations• Fittings can be rotated after assembly for easier installation
in tight spaces.
• easy to disconnect if needed• design certified and listed to ASSE 1061/NSF 61• listed by IAPMO• meets UPC, IPC and cUPC requirements• all Sharkbite® fittings are lead free