TECHNICAL DATA BOOK CONTENTS 1. REFERENCE SERVICE MANUAL·············································2 2. SPECIFICATIONS ······································································3 3. OUTLINES AND DIMENSIONS················································26 4. WIRING DIAGRAM···································································52 5. REFRIGERANT SYSTEM DIAGRAM ······································66 6. PERFORMANCE CURVES ······················································69 7. CORRECTION FACTORS························································73 8. APPLICABLE EXTENSION PIPE FOR EACH MODEL ··········74 9. AIR FLOW DATA······································································82 10. NOISE CRITERION CURVES ················································100 11. OPTIONAL PARTS···································································116 <Indoor unit> [Model names] R410A PLA-RP·AA PEAD-RP·EA PEAD-RP·GA PEA-RP·EA PEH-RP·MYA PKA-RP·GAL PKA-RP·FAL PCA-RP·GA PCA-RP·HA PSA-RP·GA <Outdoor unit> [Model names] No. OCS01 SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS PUHZ-RP35/50/60/71/100/125/140VHA PUHZ-RP100/125/140/200/250YHA May 2005 INVERTER kW Model
118
Embed
No. OCS01 TECHNICAL DATA BOOK R410A INVERTERmitsubishitech.co.uk/Data/Mr-Slim_Outdoor/PUHZ-(Z)RP/...4 Model name Indoor unit PLA-RP60AA PLA-RP71AA Outdoor unit PUHZ-RP60VHA PUHZ-RP71VHA
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
TECHNICAL DATA BOOK
CONTENTS
1. REFERENCE SERVICE MANUAL·············································22. SPECIFICATIONS ······································································33. OUTLINES AND DIMENSIONS················································264. WIRING DIAGRAM···································································525. REFRIGERANT SYSTEM DIAGRAM ······································666. PERFORMANCE CURVES ······················································697. CORRECTION FACTORS························································738. APPLICABLE EXTENSION PIPE FOR EACH MODEL ··········749. AIR FLOW DATA ······································································82
10. NOISE CRITERION CURVES ················································10011. OPTIONAL PARTS ···································································116
w If optional Air protect guide installed. D.B.-15:
Indoor unit Single phase 230V 50HzSingle phase 230V 50HzOutdoor unit
3. Guaranteed voltage 198~264V, 50Hz
Model name Indoor unit PEAD-RP100GAOutdoor unit PUHZ-RP100YHA
Cooling Capacity Btu/h 34,100kW 10.0(4.9-11.4)
Total input kW 3.08EER 3.25Energy label class ASHF 0.83
Heating Capacity Btu/h 38,200kW 11.2(4.5-14.0)
Total input kW 3.48COP 3.22Energy label class CBooster heater kW -
Power supply Phase [ 3Cycle Hz 50Voltage V 400Breaker size A 16
Indoor unit Air flow CMM 26.5-33(Low-High) CFM 935-1165External pressure Pa 10/50/70Sound level dB(A) 40-43/42-45/42-46(Low-High) (10/50/70Pa)External finish Galvanized sheetsDimension W : mm 1411
D : mm 740H : mm 275W : inch 55-9/16D : inch 29-1/8H : inch 10-13/16
Weight kg 50lbs 111
Unit drain pipe O.D. mm 32inch 1-1/4
Outdoor unit Air flow CMM 100CFM 3,530
Sound level at cooling dB(A) 49Sound level at heating dB(A) 51External finish Ivory Munsell 3Y 7.8/1.1Dimension W : mm 943
D : mm 330+30H : mm 1350W : inch 37-3/8D : inch 13 + 1-3/16H : inch 53-1/8
Weight kg 135lbs 298
Refrigerant pipe size Gas side O.D. mm 15.88inch 5/8
Liquid side O.D. mm 9.52inch 3/8
Refrigerant pipe length Height difference m Max. 30Length m Max. 75
Total input kW 1.27 1.40COP 3.23 3.21Energy label class C CBooster heater kW - -
Power supply Phase [ 1Cycle Hz 50Voltage V 230Breaker size A 16
Indoor unit Air flow CMM 9-10-11-12(Low-Medium2-Medium1-High) CFM 320-355-390-425External pressure Pa 0Sound level dB(A) 36-38-41-43(Low-Medium2-Medium1-High)
External finish White Munsell 0.70Y 8.59/0.97Dimension W : mm 990
D : mm 235H : mm 340W : inch 39D : inch 9-1/4H : inch 13-3/8
Weight kg 16lbs 35
Unit drain pipe O.D. mm 20inch 13/16
Outdoor unit Air flow CMM 35CFM 1,240
Sound level at cooling dB(A) 44Sound level at heating dB(A) 46External finish Ivory Munsell 3Y 7.8/1.1Dimension W : mm 800
D : mm 330+23H : mm 600W : inch 31-1/2D : inch 13 + 7/8H : inch 23-5/8
Weight kg 45lbs 99
Refrigerant pipe size Gas side O.D. mm 12.7inch 1/2
Liquid side O.D. mm 6.35inch 1/4
Refrigerant pipe length Height difference m Max. 30Length m Max. 50
w If optional Air protect guide installed. D.B.-15:
Indoor unit Single phase 230V 50HzSingle phase 230V 50HzOutdoor unit
3. Guaranteed voltage 198~264V, 50Hz
Model name Indoor unit PKA-RP100FALOutdoor unit PUHZ-RP100YHA
Cooling Capacity Btu/h 34,100kW 10.0(4.9-11.4)
Total input kW 2.93EER 3.41Energy label class ASHF 0.77
Heating Capacity Btu/h 38,200kW 11.2(4.5-14.0)
Total input kW 3.25COP 3.45Energy label class BBooster heater kW -
Power supply Phase 3Cycle Hz
[
50Voltage V 400Breaker size A 16
Indoor unit Air flow CMM 22-28(Low-High) CFM 780-990External pressure Pa 0Sound level dB(A) 41-46(Low-High)External finish Munsell 3.4Y 7.7/0.8Dimension W : mm 1680
D : mm 235H : mm 340W : inch 66-1/8D : inch 9-1/4H : inch 13-3/8
Weight kg 28lbs 62
Unit drain pipe O.D. mm 20inch 13/16
Outdoor unit Air flow CMM 100CFM 3,530
Sound level at cooling dB(A) 49Sound level at heating dB(A) 51External finish Ivory Munsell 3Y 7.8/1.1Dimension W : mm 950
D : mm 330+30H : mm 1350W : inch 37-3/8D : inch 13 + 1-3/16H : inch 53-1/8
Weight kg 135lbs 298
Refrigerant pipe size Gas side O.D. mm 15.88inch 5/8
Liquid side O.D. mm 9.52inch 3/8
Refrigerant pipe length Height difference m Max. 30Length m Max. 75
Total input kW 3.28 4.36 4.98COP 3.41 3.21 3.21Energy label class B C CBooster heater kW - - -
Power supply Phase [ 3Cycle Hz 50Voltage V 400Breaker size A 16
Indoor unit Air flow CMM 24-31 26-33 27-35(Low-High) CFM 850-1060 920-1165 955-1240External pressure Pa 0Sound level dB(A) 44-49 46-51 47-52(Low-High)External finish White Munsell 0.70Y 8.59/0.97Dimension W : mm 600
D : mm 350H : mm 1900W : inch 23-5/8D : inch 13-3/4H : inch 74-13/16
Weight kg 51 51 53lbs 112 112 117
Unit drain pipe O.D. mm 20inch 13/16
Outdoor unit Air flow CMM 100CFM 3,530
Sound level at cooling dB(A) 49 50Sound level at heating dB(A) 51 52External finish Ivory Munsell 3Y 7.8/1.1Dimension W : mm 950
D : mm 330+30H : mm 1350W : inch 37-3/8D : inch 13 + 1-3/16H : inch 53-1/8
Weight kg 135lbs 298
Refrigerant pipe size Gas side O.D. mm 15.88inch 5/8
Liquid side O.D. mm 9.52inch 3/8
Refrigerant pipe length Height difference m Max. 30Length m Max. 75
OCS01-1.qxp 05.5.25 11:42 AM Page 25
26
3 OUTLINES AND DIMENSIONS
PLA-RP60,71AA
PLA-RP35,50AA
Models
PLA-RP100,125,140AA
241
281
A
258
298
B
80
84
C
ReceiverOperation lamp
DEFROST/STAND BY lamp
Emergency operation switch (cooling)
A (WIRELESS PANEL)
Emergency operation switch (heating)
Branch duct hole(Cut out hole)
175
150
14 - 2.8Burring hole
350
90
70_
100 100 90
100
130
155
167
Sus
pens
ion
bolt
pitc
h
Cei
ling
hole
Branchduct hole
Suspension bolt pitch
Ceiling hole
840
197 159
159
605
159
192
98 89 C
840
860
- 91
020
- 4
520
- 4
5
20 - 4520 - 45
Fresh air intake
Branch duct hole
860 - 910
810
159
16
Terminal block
Drain pipeVP-25connection(O.D.32)
Ceiling surfacePower line entrySuspension bolt lower edge
Suspension bolt M10or W3/8
Control wire entry
Feeding hole(Drain pump)
37428660
17+
5 0 30
190
170
140
50 -
70
105
AB
1
2
High efficiency filter& Fresh air intake casement (option)
17+
5 013
5
Air outlet hole
Vane motor
Auto vane
Drain hole
Grille
Air
outle
t hol
e
Air
inta
ke h
ole
411
Air intake holeAir intake grille 577
77 51
M
M
M
A
M
950
5177
950
577
411
RP35, 50
Use the current nuts meeting the pipe size of the outdoor unit.Available pipe size
Factory flare nut attachment to the heat-exchanger.
1 LIQUID SIDE
2 GAS SIDE
RP60 RP71
[6.35 [6.35 — —
[9.52 [9.52 [9.52 [9.52
[12.7 — — —
[15.88 [15.88 [15.88 [15.88
— — — [19.05
RP100, 125, 140
Detail drawing of fresh air intake
3 - 2.8Burring hole
125Burring hole pitch
100(Cut out hole)
Ceiling surface
120_
120_
158
Unit : mmINDOOR UNITPLA-RP35AA PLA-RP50AA PLA-RP60AA PLA-RP71AAPLA-RP100AA PLA-RP125AA PLA-RP140AA
Be sure to apply the air filter near the air inlet grille.
Unit : mm
OCS01-1.qxp 05.5.25 11:42 AM Page 27
28
PEAD-RP60GAPEAD-RP71GAPEAD-RP100GA
Unit : mm
Model A B C D E
7
7
9
8
9.52
9.52
15.88
15.88
8
10
F G H J
RP60
RP71
RP100
1125
1125
1365
1090
1090
1330
1050
1050
1290
1012
1012
1252
840
840
1080
Outdoor unit(SUZ) : 6.35Other outdoor unit : 9.52 w
R410A Outdoor unit : 15.88 wR407C Outdoor unit : 19.05
w Setting at shipment
OCS01-1.qxp 05.5.25 11:42 AM Page 28
29
50 55
530
690
(130
)
22.5
4070
105 510 35
40 40650
15
15
730
155 155155
1422
012
0
3.2
300242
2656075
35
45
2034
5
11 11672
22.5
20 20690
152512512525
100
600
70(5
30)
300
900
(10)
25
562
21
(10)381
8585251570
11
14514524.5
33920
418
90
200
200
250
175
Terminal block
4-12 30 oblong Suspension bolt holes
Air intake
Air outlet
Service space(opening)in the ceiling
Heat insulator t10
(Dra
inag
e pa
n)
Room temperature thermistor
Drainage pan connection R1
Wiring entry(2-[22holes)
Refrigerant-pipe flaredconnection [15.88(5/8)
Refrigerant-pipe flaredconnection [9.52(3/8)
Electrical parts box
Service panel(Condenser/evaporator temperature thermistor)
Service panel(Room temperature thermistor)
Air intake Air intake duct flange
14-[2.9 holesFor air intake duct connection
Heat insulator t10
Air outlet duct flange Air outlet
(Drainage pan)
12-[2.9 holesFor air outlet duct connection
Mounting plate
Unit : mmPEA-RP71EA
OCS01-1.qxp 05.5.16 10:03 AM Page 29
30
Unit : mmPEA-RP100EA
50 60
690
530
27.5
15
3.2
1425
098
1000
500
2034
5
11
65656527.5
(130
)
65
15
65656539.5
(10)
562
21
(10)381
1570
11
33920418
90
200
200
250
175
24570
45
15
217
3579590
942
114070
960
6565 11=715 4040
2020
6565 7=455 22.522.5
920 4040
70
900
300
(530
)70
600
100
Terminal block
34-[2.9 holesFor air outlet duct connection
(Dra
inag
e pa
n)
Air outlet
Air intake
(Drainage pan)Drainage pan connection R1Refrigerant-pipe flared
connection [9.52(3/8)
Refrigerant-pipe flared connection [15.88(5/8)
Electrical parts box
Wiring entry(2-[22holes)
Room temperature thermistor
Air intake Air intake duct flange
Air outlet
24-[2.9 holesFor air outlet duct connection
Air outlet duct flange
Heat insulator t10
Heat insulator t10
Service space(opening)in the ceiling
Service panel(Room temperature thermistor)
Service panel(Condenser/evaporator temperature thermistor)
4-12 30 oblong Suspension bolt holes
35
Mounting plate
OCS01-1.qxp 05.5.16 10:03 AM Page 30
31
Unit : mmPEA-RP125EA
50 60
690
530
3.2
11 111142
2034
5
900
1425
084
(130
)
15
27.5 27.5 27.5
15
39.524570
45
381
1570
33920
90
200
200
250
175
65 13=845
65 14=91065
65
1160
42.5
2020
70 40
117
15
1200
405
70
112040 40
3599590
42.5
300
(530
)70
100
600
900
11
(10)
21
562
(10)
65 65 65
65 65 65 27.5
65
Refrigerant-pipe flared connection [15.88(5/8)
Refrigerant-pipe flaredconnection [9.52(3/8)
4-12 30 oblong Suspension bolt holes
Terminal block
Air outlet
Air intake
Service space(opening) in the ceiling
Air intake duct flange
(Drainage pan)
(Dra
inag
e pa
n)40-[2.9 holesFor air outlet duct connection
36-[2.9 holesFor air outlet duct connection
Drainage pan connection R1
Electrical parts box
Wiring entry(2-[22holes)
Room temperature thermistor
Air intake
Heat insulator t10
Air outlet duct flange Air outlet
Heat insulator t10
Service panel(Condenser/evaporator temperature thermistor)
Service panel(Room temperature thermistor)
35
Mounting plate
OCS01-2.qxp 05.5.16 10:05 AM Page 31
32
Unit : mmPEA-RP140EA
60
4040
37.5
381 (10)
(10)405
656539.5
339
65 65
25 100100
24570
50
45
70
160 1000
1385
9814
250
3.2
11
562
690
1415
111327
100
153
1570
159017
525
01305
45130 7=91045
15
530
(130
)20
020
0
70
15
40
65 16=104037.5
20 (20)1345
2034
5
90 1115
900
600
100
70(5
30)
300
Refrigerant-pipe flared connection [15.88(5/8)
4-12 30 oblongSuspension bolt holes
Terminal block
Refrigerant-pipe flared connection[9.52(3/8)
Air intake
Service space(opening) in the ceiling
Air outlet
130
65
(D
rain
age
pan)
Air outlet duct flange
22-[3.1 holesFor air outlet duct connection
Air outlet
44-[2.9 holesFor air outlet duct connection
Air intake duct flangeAir intake
Drainage pan connection R1 (Drainage pan)
Room temperature thermistor
Service panel(Condenser/evaporator temperature thermistor)
Wiring entry(2-[22holes)Electrical parts box
Heat insulator t10
Heat insulator t10
Service panel(Room temperature thermistor)
35
Mounting plate
OCS01-2.qxp 05.5.16 10:05 AM Page 32
33
Note: When connecting duct to the inlet side, remove the air filter attached to the unit body, and mountan air filter onto the inlet duct side separately.
(1) When connecting air inlet (2) When installing the suspension fixtures prior to installation of the indoor unit without inlet duct(3) When hanging the indoor unit directly without inlet duct
(A) Service space(B) Suspension bolt pitch(C) Air inlet(D) Air outlet
(1) When connecting air inlet (2) When installing the suspension fixtures prior to installation of the indoor unit without inlet duct(3) When hanging the indoor unit directly without inlet duct
(A) Service space(B) Suspension bolt pitch(C) Air inlet(D) Air outlet
144020
530
131
3220
019
9
40073
0
200
14802080
20020
(A) (C)
(B) (B)
(D)
AIR INLET SENSOR
REFRIGERANT PIPE [12.7 (1/2 BRAZE)
REFRIGERANT PIPE [28.6 (1-1/8 BRAZE)
AIR INLET AIR OUTLET
152
650
9515
6
344
20
15
7053050
130
130
4242
DRAIN: Rc 1
33 562
382
2510
010
025
15
210
116
928
428
500
2575 (1)
(2)
(3)
(A)
Note: When connecting duct to the inlet side, remove the air filter attached to the unit body, and mountan air filter onto the inlet duct side separately.
OCS01-2.qxp 05.5.16 10:05 AM Page 34
35
INDOOR UNITPKA-RP35GAL PKA-RP50GAL
BY
OFF
ON
STA
ND
HE
ATC
OO
L
OFF
BY
ON
STA
ND
CO
OL
HEA
T
ÅrÇ
oÇoÅ
qÅ@
ëOñ
Å@
ÇeÇ
qÇnÇ
mÇ
sÅ
rÇoÇ
oÅqÅ
@ëO
ñÅ
@Ç
eÇqÇ
nÇm
Çs
r.SLI
.SLI
mm
MIT
SU
BIS
HI E
LEC
TRIC
MIT
SU
BIS
HI E
LEC
TRIC
r.S.SLI
mm
MIT
SU
BIS
HI E
LEC
TRIC
MIT
SU
BIS
HI E
LEC
TRIC
Kno
ck o
ut h
ole
for
right
pip
ing
Ref
riger
ant p
ipe.
Dra
in p
ipe.
Wiri
ng h
ole
21
Rig
ht s
ide
Less
than
15
70245
60
235
Aut
o va
ne
Fro
nt v
iew
Air
inta
ke
Air
inta
ke
Air
inta
ke
Air intake 198
53
340
715
225
340
8028
023
3
990
21
Left
side
Kno
ck o
ut h
ole
for
left
pipi
ngR
efrig
eran
t pip
e.D
rain
pip
e.W
iring
hol
e.60
70245
(Nec
essa
ry c
lear
ance
for
Uni
t ins
talla
tion)
Rig
ht s
ide
Allo
win
g cl
eara
nces
Fro
nt v
iew
Less
than
130
50 o
r m
ore
150
or m
ore
180 or more30 or more
for
bolts
Left-
rear
pi
ping
hol
e
left-
rear
pip
ing
R52
.5R
52.5
Inst
alla
tion
plat
eba
lanc
e po
int h
ole
Det
ails
of i
nsta
llatio
n pl
ate
49-[
5hol
efo
r ta
ppin
g sc
rew
Kno
ck o
ut h
ole
for
right
-rea
r pi
ping
Rig
ht-r
ear
pipi
ng h
ole
Uni
t cen
ter
14-[
14ho
le
Kno
ck o
ut h
ole
for
425
420
170190
210230
0
322
0 35 55 80 130
190
230
272
310
0
35
95
150
205
260
320345
495
20
75
135
190
245
300
360
405
495
32
0
w1
Sle
eves
are
ava
ilabl
e on
the
mar
ket.
w2
Thi
s si
ze s
how
s th
e lo
wer
end
of t
hrou
gh h
ole.
[90
~[
100
[90
Thro
ugh
hole
Sle
eve
w1
35, 5
0M
odel
R52.5
R52.5
Gas
pip
eLi
quid
pip
e
Term
inal
blo
ck fo
r
Term
inal
blo
ck to
outd
oor
unit
Filt
er g
rip
Ser
vice
pan
el(P
ower
sup
ply
acce
ss)
(Fle
xibl
e ho
se to
tal l
engt
h800
)(R
ight
sid
e pi
ping
inst
alla
tion)
(Lef
t sid
e pi
ping
inst
alla
tion)
Uni
t dra
in p
ipe
O.D
.20
Fro
nt v
iew
(to
open
the
grill
e)
700
449
86
581
54
31280
35
Kno
ck o
ut h
ole
for
unde
r pi
ping
Ref
riger
ant p
ipin
g.D
rain
pip
e.W
iring
hol
e
12-L
ouve
rs(m
anua
l)
Air
outle
tLo
wer
sid
e
80
50
395
400
190
60
7035
79
160
40
235
705
pow
er s
uppl
y (H
eate
r (P
KH
-P35
, 50G
ALH
onl
y))
153
GA
S S
IDE
LIQ
UID
SID
E
RP
35, 5
0P
35, 5
0
[6.
35
[9.
52
[12
.7
[15
.88
—
[9.
52 —
[15
.88
Use
the
curr
ent n
uts
mee
ting
the
pipe
siz
e of
the
outd
oor
unit.
Ava
ilabl
e pi
pe s
ize
: Fac
tory
flar
e nu
t atta
chm
ent t
o th
e he
at -
exc
hang
er.
Unit : mm
OCS01-2.qxp 05.5.16 10:05 AM Page 35
36
Unit : mmPKA-RP60FALPKA-RP71FAL
235452354523545235
62.5
13
5842
340 19
7
Top
Front Right side
Left side 14001090 Air intake
235
C
Knock out hole for right piping
Refrigerant pipe. Drain pipe
Knock out hole for left piping
Drain hose forleft-hand side piping
Drain hose
Lower side
Auto vanes
(Gas pipe)Drain hose O.D.20
Bolt
Gas pipe
15
(Liquid pipe)
Liquid pipe [9.52(3/8F)Gas pipe [15.88(5/8F)
Liquid pipe
A
30
3239
9837
74
439
100
30
3774 4
2980
280
303018
430
60
10
393765
100
A B C
Knock out hole for wiring
25
1110 183
240
B
1120552
55120
107111
Air outlet552 Air outlet
Louvers (manual)Under panelRemovable at left-handside piping Knock out hole for under-piping
Refrigerant pipe. Drain pipe
Rear piping opening
Range for left rear piping opening12-ø6 hole fortapping screw
66-ø6 hole fortapping screw
Wall fixture
Unit center
32-ø12 hole for bolt225
18 18 91900
990455
285
245
19
240 280 314610 90
Drainage rangeon left-hand side
Drainage rangeon right-hand side
10 91=(910)
180
Terminal block for heater (PKH only)
Terminal block for indoor/outdoor connecting line
Display section
Receivingsection
Power lamp
Emergency switch(Heat)
Emergency switch(Cool)
Defrosting Initial heating lamp
OCS01-2.qxp 05.5.16 10:05 AM Page 36
37
Unit : mmPKA-RP100FAL
23545 235452354523545235
62.5
13
5842
340 19
7
Top
FrontRight side
Display section
Receivingsection
Power lamp
Emergency switch(Heat)
Emergency switch(Cool)
Defrosting Initial heating lamp
Left side 16801370 Air intake
235
C
Knock out hole for right piping
Knock out hole for left piping
Drain hose for left-hand side piping
Drain hose
Drain hose Lower side
Auto vane
(Gas pipe)
Bolt
Gas pipe
15
(Liquid pipe)
Liquid pipe
A
30
3239
9837
74
439
100
30
3774 4
2980
280
303018
430
60
10
393765
100
A B C
Knock out hole for wiring
25
1110 183
240
B
1400
55120
102111
694 Air outlet 694 Air outlet
Louvers (manual)
Under panel(Removable at left-hand side piping)
Knock out hole for under-piping
Refrigerant pipe. Drain pipe
Rear piping opening
Range for left rear piping openingRange for left rear piping opening
12-ø6 hole for tapping screw
84-ø6 hole fortapping screw
Wall fixture
Unit out lineUnit center
41-ø12 hole for bolt295 225
18 1891
900
1270595
285
245
19
240 280 314750 90
Drainage rangeon right-hand side
13 91=(1183)
180
Drainage rangeon left-hand side
Terminal block for heater (PKH only)
Terminal block for indoor/outdoor connecting line
Drain hose O.D.20
: Factory flare nut attachment to the heat-exchanger.
GAS SIDE
LIQUID SIDE
RP100
[9.52
[15.88
[19.05
P100
[9.52
[19.05
Use the current nuts meeting the pipe sizeof the outdoor unit.Available pipe size
OCS01-2.qxp 05.5.16 10:05 AM Page 37
38
INDOOR UNITPCA-RP50GA
NOTES:1. Use M10 or W3/8 screws for anchor bolt.2. When optional drain lift-up mechanism is installed, always provide
upward piping for refrigerant piping.
180
210
157
1585
182 liquid
201 gas
241 (Drainage)
Air intake
918
161 90
254
680
506
56Electrical box
226
70
6
2
7
1715
0
140 70 320
80
933 (suspension bolt pitch)
983
1000
Air outlet
81
904
76
525
928352
263171138
86
4617
51
131
3838
79
161
32
179
42
6~7
Ceiling
Electrical box [Front view]
When electricalbox is pulleddown
32
8
5 1 4
[15.88
[9.52
P50
[15.88
[12.7
[6.35
Available pipe size
[9.52
4 GAS SIDE
5 LIQUID SIDE
RP50
Use the current nuts meeting the pipe size of the outdoor unit.
: Factory flare nut attachment to the heat-exchanger.
1 Drainage pipe connection (26mm I.D.)2 Drainage pipe connection (for the left arrangement)3 Knock out hole for left drain-piping arrangement4 Refrigerant-pipe connection (gas pipe side/flared connection)5 Refrigerant-pipe connection (liquid pipe side/flared connection)6 Knock out hole for upper drain pipe arrangement7 Knock out hole for left drain pipe arrangement8 Knock out hole for wiring arrangement
Unit : mm
OCS01-2.qxp 05.5.16 10:05 AM Page 38
39
PCA-RP60GAPCA-RP71GA
161 90
254
680
506
56
1240 (suspension bolt pitch)
140
150
320
80
17
70
6
1290
1214
210
180
8176
1310
Air outlet
1228
Air intake
85
182
201
241
15
157
(liquid)
(5/8F gas)
(Drainage)
7
2
Electrical box70
226
32
8
5 1 4Electrical box
When electricalbox is pulleddown
[ Front view ]
Ceiling32
179
161
3838
79
42
6~7
5251235
416263
171138
86
131
175
146
: Factory flare nut attachment to the heat-exchanger.
4 GAS SIDE
5 LIQUID SIDE
Use the current nuts meeting the pipe size of the outdoor unit.
Available pipe sizeRP71,P60,P71RP60
[6.35
[9.52
[15.88
[9.52
[15.88
1 Drainage pipe connection (26mm I.D.)2 Drainage pipe connection (for the left arrangement)3 Knock out hole for left drain-piping arrangement4 Refrigerant-pipe connection (gas pipe side/flared connection)5 Refrigerant-pipe connection (liquid pipe side/flared connection)6 Knock out hole for upper drain pipe arrangement7 Knock out hole for left drain pipe arrangement8 Knock out hole for wiring arrangement
Unit : mm
NOTES:1. Use M10 or W3/8 screws for anchor bolt.2. When optional drain lift-up mechanism is installed, always provide
upward piping for refrigerant piping.
OCS01-2.qxp 05.5.16 10:05 AM Page 39
40
PCA-RP100GA
161 90
254
680
506
56
1228
Air intake
121427
0
207
8196
1310
Air outlet
1240 (suspension bolt pitch)
140
150
320
80
18
70
6
87
182
198
245
16
217
(3/8F liquid)
(5/8F, 3/4F gas)
(Drainage)
7
2
Electrical box70
229
32 8
5 1 4Electrical box
When electricalbox is pulleddown
[ Front view ]
Ceiling9316
0
3838
140
4223
9
6~7
5251235
687263
171138
86
192
236
145 Use the current nuts meeting the pipe size of the outdoor unit.
:Factory flare nut attachment to the heat-exchanger.
4 GAS SIDE
5 LIQUID SIDE
Available pipe sizeRP100
[9.52
[15.88
[19.05
P100
[9.52
[19.05
1 Drainage pipe connection (26mm I.D.)2 Drainage pipe connection (for the left arrangement)3 Knock out hole for left drain-piping arrangement4 Refrigerant-pipe connection (gas pipe side/flared connection)5 Refrigerant-pipe connection (liquid pipe side/flared connection)6 Knock out hole for upper drain pipe arrangement7 Knock out hole for left drain pipe arrangement8 Knock out hole for wiring arrangement
Unit : mm
NOTES:1. Use M10 or W3/8 screws for anchor bolt.2. When optional drain lift-up mechanism is installed, always provide
upward piping for refrigerant piping.
OCS01-2.qxp 05.5.16 10:05 AM Page 40
41
PCA-RP125GAPCA-RP140GA
161 90
254
68
0
506
56
1535
Air intake
15242
70
20
7
81
96
1620
Air outlet
1547(suspension bolt pitch)
140
15
0
32
08
0
18
70
6
87
182
198
245
16
21
7
(3/8F liquid)
(5/8F, 3/4F gas)
(Drainage)
7
2
Electrical box70
229
32 8
5 1 4Electrical box
When electricalbox is pulleddown
[ Front view ]
Ceiling93
160
38
38
140
42
239
6~
7
5251545
687263
171138
86
192
236
145
:Factory flare nut attachment to the heat-exchanger.
RP125,140
[19.05[15.88
[9.52
Use the current nuts meeting the pipe size of the outdoor unit.
4 GAS SIDE
5 LIQUID SIDE
Available pipe sizeP125,140
[19.05
[9.52
1 Drainage pipe connection (26mm I.D.)2 Drainage pipe connection (for the left arrangement)3 Knock out hole for left drain-piping arrangement4 Refrigerant-pipe connection (gas pipe side/flared connection)5 Refrigerant-pipe connection (liquid pipe side/flared connection)6 Knock out hole for upper drain pipe arrangement7 Knock out hole for left drain pipe arrangement8 Knock out hole for wiring arrangement
Unit : mm
NOTES:1. Use M10 or W3/8 screws for anchor bolt.2. When optional drain lift-up mechanism is installed, always provide
upward piping for refrigerant piping.
OCS01-2.qxp 05.5.25 11:45 AM Page 41
42
Cei
ling
Less than
Less than
or more
Less
than
or m
ore
or m
ore
300
<S
uspe
nsio
n bo
lt pi
tch>
mod
el:P
AC
-SG
38K
F-E
(12
pcs.
)F
ilter
ele
men
t for
the
exch
ange
1.U
se M
10 o
r W
3/8
scre
w fo
r an
chor
bol
t.N
OT
ES
.
Opt
ion
part
s:du
ct fl
ange
( [
200
). m
odel
: PA
C-S
F28
OF
-E(1
pcs
.)
Kno
ck o
ut h
ole
for
wiri
ng a
rran
gem
ent :
2- [
27
(122
)
<F
ilter
con
tour
dim
ensi
on>
16ha
ndle
100
100
1136
366
480
176
318
650
<F
lexi
ble
hose
(acc
esso
ry)>
Ter
min
al b
lock
box
9T
erm
inal
blo
ck(r
emot
e co
ntro
ller)
8T
erm
inal
blo
ck(in
door
/out
door
con
nect
ing
line)
78
Insp
ectio
n po
rt
(pi
pe s
enso
r)T
he h
alf b
otto
m o
f FA
N C
AS
ING
can
be s
epar
ated
.A
djus
tabl
e pa
rt
288
360
<Air outlet>
<S
uspe
nsio
n bo
lt pi
tch>
<A
ir ou
tlet>
<A
ir in
take
>
<Air intake>F
ilter
(3-
piec
es)
Ter
min
al b
lock
box
5 2
1
4
3
Kno
ck o
ut h
ole
for
uppe
r re
frig
eran
t-pi
pe a
rran
gem
ent
6
92
1
Fle
xibl
e ho
se(a
cces
sory
)
Dra
inag
e pi
pe c
onne
ctio
n(26
mm
I.D
.)2
Ref
riger
ant-
pipe
con
nect
ion(
gas
pipe
sid
e/fla
red
conn
ectio
n : 5
/8F
)
38
10585
90˚
Ele
ctric
al b
ox
Rea
r w
all
500
250
2 ~ 3
(Gap to ceiling)
Allo
win
g cl
eara
nces
<gas>
<liquid>
7
Kno
ck o
ut h
ole
(duc
t for
fres
h ai
r in
take
): 2
- [
200
651 3 4K
nock
out
hol
e fo
r be
hind
ref
riger
ant-
pipi
ng a
rran
gem
ent
Ref
riger
ant-
pipe
con
nect
ion(
liqui
d pi
pe s
ide/
flare
d co
nnec
tion
: 3/8
F)
Sus
pens
ion
bolt
130
210
45
165120
1224
1180
75
1136
986
1098
70
243
254
175
197
11021
130
15
258110102
320
80
90
140
1875
70~90
650
13
289
75
280
495
43
295
[22
2
[20
0
PCA-RP71HA Unit : mm
OCS01-2.qxp 05.5.25 11:45 AM Page 42
43
Cei
ling
Less than
Less than
Less
than
or more
or m
ore
or m
ore
431 5 6 72 8 9
Ref
riger
ant-
pipe
con
nect
ion(
gas
pipe
sid
e/fla
red
conn
ectio
n : 5
/8F
, 3/4
F)
Kno
ck o
ut h
ole
(duc
t for
fres
h ai
r in
take
) : 2
- [
200
Opt
ion
part
s:du
ct fl
ange
( [
200
). m
odel
: PA
C-S
F28
OF
-E(1
pcs
.)
Fle
xibl
e ho
se(a
cces
sory
)
Dra
inag
e pi
pe c
onne
ctio
n(26
mm
I.D
.)
Ter
min
al b
lock
(indo
or/o
utdo
or c
onne
ctin
g lin
e)T
erm
inal
blo
ck(r
emot
e co
ntro
ller)
Ref
riger
ant-
pipe
con
nect
ion(
liqui
d pi
pe s
ide/
flare
d co
nnec
tion
: 3/8
F)
Kno
ck o
ut h
ole
for
behi
nd r
efrig
eran
t-pi
ping
arr
ange
men
tK
nock
out
hol
e fo
r up
per
refr
iger
ant-
pipe
arr
ange
men
tK
nock
out
hol
e fo
r w
iring
arr
ange
men
t : 2
- [
27
Allo
win
g cl
eara
nces
Rea
r w
all
(Gap to ceiling)
NO
TE
S.
1.U
se M
10 o
r W
3/8
scre
w fo
r an
chor
bol
t.
Use
the
curr
ent n
uts
mee
ting
the
pipe
siz
eof
the
outd
oor
unit.
mod
el:P
AC
-SG
38K
F-E
(12
pcs.
)F
ilter
ele
men
t for
the
exch
ange
<S
uspe
nsio
n bo
lt pi
tch>
(122
)24
6
hand
le
16
<F
lexi
ble
hose
(acc
esso
ry)>
Ter
min
al b
lock
box
78
<F
ilter
con
tour
dim
ensi
on>
Insp
ectio
n po
rt
(pi
pe s
enso
r)T
he h
alf b
otto
m o
f FA
N C
AS
ING
can
be s
epar
ated
.A
djus
tabl
e pa
rt
288
360
<Air outlet>
<S
uspe
nsio
n bo
lt pi
tch>
<A
ir ou
tlet>
<A
ir in
take
>
<Air intake>
Filt
er (
4-pi
eces
)
Ter
min
al b
lock
box
5 2
1
4
3
69
21
176
38210
10585
45 165
[22
2
[20
0
440
440
298
130
90˚
650
300
100
1520
100
Ele
ctric
al b
ox
500
250
2~3
<gas>
<liquid>
Sus
pens
ion
bolt
70
243
254
175
197
11021
130
15
258
1482
110102
1370
75
1608
320
8015
64
1520
90120
140
1875
70~90
650
13
289
75
280
495
43
295
[ 9
.52
RP
125
[ 1
5.88
[ 1
9.05
Ava
ilabl
e pi
pe s
ize
2 L
IQU
ID S
IDE
1 G
AS
SID
E
: Fac
try
flare
nut
atta
chm
ent t
o th
e he
at-e
xcha
nger
PCA-RP125HA Unit : mm
OCS01-2.qxp 05.5.25 11:45 AM Page 43
44
125
240
Fro
nt s
ide
Met
al fi
xtur
eag
ains
t ove
rtur
ning
cont
rolle
r
Rea
r si
de
Kno
ck o
ut h
ole
for
bran
ch d
uct
100
10
38 38
50 260
130 130
766
1900
608
50
115
714123
767
110480
590
216
40
827 3020 10
11115
130
132
VIE
W "
A"
A
340
370
520
260
240
130
71
530
600
270
250
70
180
235
Kno
ck o
ut h
ole
for
wiri
ng.[
27(P
rovi
ded
on b
oth
side
s)
Kno
ck o
ut h
ole
for
refr
iger
ant a
nd d
rain
age.
90
60 o
val (
Pro
vide
d on
bot
h si
des)
Kno
ck o
ut h
ole
for
pipi
ng a
nd w
iring
(140
80
ova
l)
2010
5
Ter
min
al b
lock
for
indo
or/o
utdo
orco
nnec
tion.
Ele
ctric
al p
arts
box
Liqu
id p
ipe [
9.52
(3/8
F)
1. S
ervi
ce a
cces
s al
low
s fo
r
inse
rtio
n of
scr
ew d
river
.2.
Adj
usta
ble
Gas
pip
e [
15.8
8(5/
8F)
Dra
in p
ipe
Ter
min
al b
lock
for
heat
er p
ower
sup
ply
(Onl
y P
SH
-P•G
AH
)
9546
122
47Fro
nt s
ide
Rea
r si
de
Kno
ck o
ut h
ole
for
botto
m fi
xing
Kno
ck o
ut h
ole
for
unde
r-pi
ping
Kno
ck o
ut h
ole
for
unde
r-pi
ping
(120
70
ova
l)
277
16020
218
175
90
55143
100
95
4066 18
6
100
or m
ore
100
or m
ore
25 or more
1300 or more
Fro
nt 1
,000
or
mor
e
10
PSA-RP71GA Unit : mm
OCS01-2.qxp 05.5.25 11:45 AM Page 44
45
125
240
Fro
nt s
ide
Met
al fi
xtur
eag
ains
t ove
rtur
ning
cont
rolle
r
Rea
r si
de
Kno
ck o
ut h
ole
for
bran
ch d
uct
100
10
38 38
50 260
130 130
766
1900
608
50
115
714123
767
110480
590
216
40
827 3020 10
11115
130
132
340
370
520
260
240
130
71
530
600
350
330
70
260
315
Kno
ck o
ut h
ole
for
wiri
ng.[
27 (
Pro
vide
d on
bot
h si
des)
Kno
ck o
ut h
ole
for
refr
iger
ant a
nd d
rain
age.
90
60 o
val (
Pro
vide
d on
bot
h si
des)
Kno
ck o
ut h
ole
for
pipi
ng a
nd w
iring
(140
80
ova
l)
2010
5
Ele
ctric
al p
arts
box
Liqu
id p
ipe
[9.
52(3
/8F
)
1. S
ervi
ce a
cces
s al
low
s fo
r
inse
rtio
n of
scr
ew d
river
.2.
Adj
usta
ble
Gas
pip
e[
15.8
8(5/
8F)
[19
.05(
3/4F
)
Dra
in p
ipe
9546
122
47Fro
nt s
ide
Rea
r si
deK
nock
out
hol
efo
r bo
ttom
fixi
ng
Kno
ck o
ut h
ole
for
unde
r-pi
ping
Kno
ck o
ut h
ole
for
unde
r-pi
ping
(120
70
ova
l)
277
12020
218
255
140
77201
120
95
4066 26
1
100
or m
ore
100
or m
ore
25 or more
1300 or more
Fro
nt 1
,000
or
mor
e
10
VIE
W "
A"
A
Ter
min
al b
lock
for
indo
or/o
utdo
orco
nnec
tion.
Ter
min
al b
lock
for
heat
er p
ower
sup
ply
(Onl
y P
SH
-P•G
AH
)
[ 9
.52
RP
100,
125,
140
[ 1
5.88
[ 1
9.05
Use
the
curr
ent n
uts
mee
ting
the
pipe
siz
eof
the
outd
oor
unit.
Ava
ilabl
e pi
pe s
ize
LIQ
UID
SID
E
GA
S S
IDE
[ 9
.52
P10
0,12
5,14
0
— [ 1
9.05
: Fac
try
flare
nut
atta
chm
ent t
o t
he h
eat-
exch
ange
r
PSA-RP100GAPSA-RP125GAPSA-RP140GA
Unit : mm
OCS01-2.qxp 05.5.25 11:45 AM Page 45
46
Service panel for charge plug
w 1 In the place where short cycle tends to occur, cooling and heating capacity and power consumption might get lowered 10%. Air outlet guide (optional PAC-SG58SG) will help them improve.
w 2 If air discharges to the wall, the surface might get stained.
Minimum installation space for outdoor unit
100 mm or more as long as no obstacle is placed on the rear and light-and-left sides of the unit.
2 sides should be open in the right, left and rear side.
w 2w 1
100 mm or more
500 mm or more
Bas
ical
ly o
pen
100 mm or more
Free space around the outdoor unit (basic example)
350 mm or more
w 1
Air intake
Air discharge
Air intake
Connection for gas pipe
Service port
Connection for liquid pipe
Service panel4-10 o 21 oval hole(M10 foundation bolt)
[33 drain hole
[33 drain hole
43.6
152
155
400
347.5
45.4
365
330
300
40
Handle for moving
600
10
300
150
287.5
Installation bolt pitch: 500
800
69
35 43
183
90155
23
32.5
18
1. FOUNDATION BOLTS 2. PIPING-WIRING DIRECTIONPiping and wiring connection can be made from the rear direction only.
3. ATTACHING THE CONDUITIn order to attach the conduit, it is necessary to fix the metal plate with 2 screws to the back panel. Procure the metal plate and make screw holes locally. It is recommended to use the metal plate shown below. Align the metal plate to the marks on the unit and attach it.
<Foundation bolt height>
Please secure the unit firmly with 4 foundation (M10) bolts. (Bolts, washer and nut must be purchased locally.)
18 o
r bel
ow
4020
60 80
w Conduit hole
w The position and the size of conduit hole depend on the conduit to be used.
Holes for metal plate fixing screww The size of hole depends on the screw to be used.
NOTES:1.Symbols used in wiring diagram above are, : Connector, : Terminal (block).2.Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1,S2,S3).3.Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.4.This dlagram shows the wiring of Indoor and Outdoor connecting wires (specification of 230V), adopting superimposed system of power and signal.
1 ; When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig1. 2 ; For power supply system of this unit, refer to the caution label located near this diagram.
Please set the voltage using theremote controller.For the setting method. please refer tothe indoor unit Installation Manual.
Refer to tables1 and 2 Please set the voltage using
the remote controller.For the setting method,pleaserefer to the indoor unitinstallation Manual.
Table 2
Table 1
21
BLUBLU
TB5 w2;For power supply system of this unit, refer to the caution label located near this diagram.
w1;When work to supply power separately to Indoor and Outdoor unit was applled, refer to Fig 1.
:Connector,[NOTES]1.Symbols used in wiring diagram above are,
2.Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers(S1,S2,S3).3.Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.4.This diagram shows the wiring of Indoor and Outdoor connecting wires(speclfication of 230V), adopting superimposed system of power and signal.
ROOM TEMPERATURE THERMISTOR(0;/15K', 25;/5.4K' DETECT)PIPE TEMPERATURE THERMISTOR/LIQUID(0;/15K', 25;/5.4K' DETECT)COND./EVA. TEMPERATURE THERMISTOR(0;/15K', 25;/5.4K' DETECT)
Caution, 1. To protect fan motor from abnormal current,over current relays is installed. Therefore, do not change factory set value of over current relays.
51F
INDOORCONTROLLER BOARD
POWER BOARDINDOOR
TO OUTDOOR UNITCONNECTING WIRES (POLAR)
REMOTE CONTROLLER BOARD
Note:1. The dotted lines show field wiring.2. Color of earth wire is yellow and green twisting.3. Specification subject to change without notice.4. Indoor and outdoor connecting wires are made with polarities, make sure matching wiring and terminal.5. Emergency operation
If a trouble occurs with either the remote controller or the indoor microcom- puter and no other trouble exists, emergency operation for cooling or heating can be performed by changing the setting of switch (SWE) "ON" on the indoor controller board.
6. SW2(*1) shows PEH-RP250MYA setting. In case of PEH-RP200MYA setting is shown as below.
7. mark is connector.
FERRITE CORESURGE KILLER
FBCR
INDOOR CONTROLLER BOARD
SYMBOL NAMEMF151F
49FTB2,4,5TH1TH2
FAN MOTOR (INDOOR)OVER CURRENT RELAY (INDOOR FAN MOTOR)
INTERNAL THERMOSTAT (INDOOR FAN MOTOR)TERMINAL BLOCK
THERMISTOR
INDOOR UNIT
REMOTE CONTROLLER
FUSE FUSE (T6.3AL250V)ZNR VARISTOR
AUXILIARY RELAYX4-6
SW2SWELED1 LED (POWER SUPPLY)LED2 LED (POWER SUPPLY<REMOTE CONTROLLER>)LED3 LED (TRANSMISSION<INDOOR•OUTDOOR>)
NOTES:1. Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.2. Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1, S2, S3).3. Make sure that the main power supply of the booster heater is independent.4. Symbols used in wiring diagram above are, : Connector, : Terminal (block).w1. When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig 1.w2. For power supply system of this unit, refer to the caution label located near this diagram.
OCS01-2.qxp 05.5.16 10:05 AM Page 57
58
PKA-RP60FAL PKA-RP71FAL PKA-RP100FAL
INTAKECN20(RED)
LIQUIDCN21(WHT)
PIPECN29(BLK)
1 2 1 2 1 2
1 31 31 3 1 2
TH5TH1 TH2
REMOCONCN22(BLU)1 2
21
TB5
R.B
TB621
TRANSMISSION WIRES DC12V
SWEONOFF
SW2 SW1
LED3 LED2 LED1
ZNR
FUSE
X4
CN41 CN2L
CN51 CN32
WIRELESSCN90(WHT)
VANECN6V(GRN) MV
6
W.B
BZ CNB
RECEIVERRU
LED1 LED2 SW2 SW1
9
FAN(WHT)
1 3 5
1
12
12
32 3
BLK
WH
T
WH
T
RED
RED
C
MF
X4BCR
TO OUTDOOR UNIT
TB4S1S2S3
YLW
ORNORN
BRNYLW
OR
N
BLK
WH
T
P.B
I.B
Please set the voltageusing the remote controller.For the setting method,please refer to the indoorunit Installation Manual
NOTES:1. Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.2. Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1, S2, S3).3. Make sure that the main power supply of the booster heater is independent.4. Symbols used in wiring diagram above are, : Connector, : Terminal (block).w1. When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig 1.w2. For power supply system of this unit, refer to the caution label located near this diagram.
NOTES:1. Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.2. Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1, S2, S3).3. Make sure that the main power supply of the booster heater is independent.4. Symbols used in wiring diagram above are, : Connector, : Terminal (block).
W1. When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig 1.W2. For power supply system of this unit, refer to the caution label located near this diagram.
[Servicing]Fasten terminal of the terminal board "TB4"equips lock system.To remove the fastened terminal, pull it while pressing the protrudingportion (locking lever) of the terminal. The fastened terminal protrudingportion should face upward.
When installing drain-upmachine (Optional part).
WWhen installing optional drain-up machine disconnect the CN31 jumper connector and replace it with the drain sensor (DS).
Please set the voltage using theremote controller.For the setting method, please refer to the indoor unit Installation Manual.
3131POWER
CND(ORN)
INDOOR/OUTDOORCOMMUNICATION
CN3C(BLU)
TB4
POWER SUPPLY~(1PHASE)230V 50Hz
REDTB2
BLU
TO OUTDOOR UNIT
L
S1
S2
S3
N
I.B YLW
ORN
ORNORN
YLW
GRN/YLW
BRN
w1 (Fig.1)
NOTES:1.Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.2.Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1,S2,S3).3.Symbols used in wiring diagram above are, : Connector, : Terminal (block). 1 ; When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig1. 2 ; For power supply system of this unit, refer to the caution label located near this diagram.
OCS01-2.qxp 05.5.16 10:05 AM Page 60
61
PSA-RP71GA PSA-RP100GA PSA-RP125GA PSA-RP140GA
1 3 5 7
MFORN
CRED
BLK
BLU
YLW
1 3 1 3 1 3 1 2
12
21
3
1 3
ML
YLW
YLW
BLK
OR
N
YLW
YLW
ORN
S1
S2
S3
WH
T
WH
T
WH
T
BR
NO
RN
RE
D
I.BFAN(WHT)
LOUVERCNL(YLW)
X4X5X6
X6 X5 X4
X2 ZNR
FUSE
X2
LED3 LED2 LED1
SWEON
OFF
POWERCNDK(RED)
POWERCND(ORN) POWER
CN2D(WHT)
WIRELESSCN90(WHT)
21
REMOCONCN22
(BLU)
CN32CN2L
2
1
TB6
2
21
121
LIQUIDCN21(WHT)INTAKECN20(RED)PIPECN29(BLK)
CN24 CN41
CN51
R.B
TRANSMISSION WIRES DC12V
BLU
BLUTH1
TH2
TH5
SW1SW2
TB4
REDRED
WHT
RED
BLU
GRN/YLW
88HFS1FS2
H
5 312
L
N
TB2
POWER SUPPLY~(1 PHASE)230V 50Hz
21
65
RED
REDYLW
26H
88HYLW
YLW1 6
HEATERCN24(YLW)
I.B
PSH -P.GAHmodels only
INDOOR UNIT
Please set the voltage using theremote controller.For the setting method, please refer to the indoor unit Installation Manual.
INDOOR/OUTDOORCOMMUNICATION
CN3C(BLU)
Refer to tables 1and 2 for service PCB.
P.B
CNSK(RED)
CN2S(WHT)
DC13.1V
TO OUTDOOR UNIT
3131POWER
CND(ORN)
INDOOR/OUTDOORCOMMUNICATION
CN3C(BLU)
TB2
TB4
POWER SUPPLY~(1PHASE)230V 50Hz
REDBLU
GRY/YLW
REDBLU TO
OUTDOOR UNIT
L
S1S2
S3
N
I.B
YLW
ORN
ORNBR
N
1 (Fig.1)
Service boardSW2
Table 2
1 2 3 4 5
MODELS
PSA-RP71GAPSH-P71GAH
PSA-RP100GAPSH-P100GAH
PSA-RP125GAPSH-P125GAH
PSA-RP140GAPSH-P140GAH
ONOFF
1 2 3 4 5ONOFF
1 2 3 4 5ONOFF
1 2 3 4 5ONOFF
Service boardSW2
Table 1
1 2 3 4 5
MODELS
PSA-RP.GAPSH-P.GAH
ONOFF
P.B INDOOR POWER BOARDSYMBOL NAME SYMBOL NAME SYMBOL NAME
[NOTES]1.Symbols used in wiring diagram above are, : Connector, : Terminal (block).2.Indoor and outdoor connecting wires are made with polarities, make wiring matching terminal numbers (S1,S2,S3).3.Since the outdoor side electric wiring may change be sure to check the outdoor unit electric wiring for servicing.4.This diagram shows the wiring of Indoor and Outdoor connecting wires (specification of 230V), adopting superimposed system of power and signal.
1 ; When work to supply power separately to Indoor and Outdoor unit was applied, refer to Fig1.
2 ; For power supply system of this unit, refer to the caution label located near this diagram.
SW12 Switch (Address setting. 2nd digit )LED1 LED (Power Supply: DC5V)LED2 LED (Connection to Outdoor Unit)LED3 LED (Transmission: Sending)LED4 LED (Transmission: Receiving)LED5 LED (Power Supply: DC12V)
TB2 Terminal Block (Indoor/Outdoor )Motor for CompressorFan Motor Solenoid Valve (Four-Way Valve)
High Pressure SwitchSV Solenoid Valve (Bypass Valve)
8-1. PUHZ-RP·VHA, PUHZ-RP100~140YHAThe height difference between indoor and outdoor unit should be kept within 30 m for all models.(1) 1:1 system(a) Maximum pipe length
(b) Adjusting the amount of refrigerant• Additional refrigerant charge is not necessary for the pipe length up to 30 m. When the pipe length exceeds 30 m or service
(refrigerant replacement) is performed, charge proper amount of refrigerant for each pipe length referring to table below.Use refrigerant R410A. Use charge hose exclusive for R410A.
• When charging additional refrigerant, charge the refrigerant from low-pressure side of the port valve using a safety charger.• Make sure that air purge for this unit at refrigerant replacement is performed from both high-pressure check valve and ser-
vice port. If air purge is performed only from one of them, air in not purged enough.• When replacing refrigerant, charge the refrigerant from service port. When charged refrigerant is less than specified amount,
charge the refrigerant again from low pressure side of the port valve using a safety charger.• Tighten the service port cap (nut) of stop valve firmly. The tightening torque is 12 to 16 N·m. (to prevent slow-leak)• Check additional refrigerant charging amount referring to table 4 when liquid pipe is one size larger than standard diameter,
and table 2 when the pipe is standard diameter.
Liquid pipe(mm)Gas pipe(mm)
[6.35 [9.52 [12.7
[9.52
ODThick-ness
ODThick-ness
RP35RP50RP60RP71RP100RP125RP140
t0.8
[12.7
t0.8
[15.88
t1.0
[12.7
t0.8
[15.88
t1.0
[19.05
t1.0
[15.88
t1.0
[19.05
t1.0
t0.8 t0.8
: Standard piping: It can be used, however, additional refrigerant charge is required when the pipe length exceeds 20m. Refer to <table 4>.: It cannot be used.: It can be used.: It can be used, however, the capacity is lowered. Refer to (c) Capacity correction.
<Table 1> Pipe length for 1:1 system
*1: Set DIP SW8-1 on outdoor unit controller board to ON.*2: The maximum length is 50 m in case of using existing pipes.
[Marks in the table above]
50m
t0.8
30m 30m
10m 30m 30m50m
30m
50m
50m
10m
50m (*1)75m (*2)50m
10m 30m 30m10m 50m
75m (*2)
75m (*2)
50m (*1)
30m (*1)
50m (*1)
50m (*1)50m (*1)
50m (*1)
50m10m 30m 30m 30m (*1)
15 30m orabove
31 — 40m
0.2kg
0.6Kg
0.6kg
10m or below
41 — 50m
0.4kg
1.2Kg
1.2kg
51 — 60m
—
—
1.8kg
61 — 75m
—
—
2.4kg
<Table 2> Additional refrigerant charging amount for pipe of standard diameter
<Table 3>
Outdoor unit Permittedpipe length
Additional refrigerant charging amount for pipelength exceeding 30 m (kg)
PUHZ-RP35, 50VHA
PUHZ-RP60, 71VHA
PUHZ-RP100-140VHA, RP100-140YHA
Outdoor unit
Number ofbends
Heightdifference
50m or less
50m or less
75m or less
Permitted pipe length
50m or less
50m or less
75m or less
2.1
3.1
4.6
11 — 20m 21 — 30m
2.3
3.3
4.8
2.5
3.5
5.0
31 — 40m
2.7
(0.2)
4.1
(0.6)
5.6
(0.6)
2.9
(0.4)
4.7
(1.2)
6.2
(1.2)
—
—
—
—
6.8
(1.8)
—
—
—
—
7.4
(2.4)
41 — 50m 51 — 60m 61 — 75m
Recharge refrigerant amount or additional amount in parentheses
PUHZ-RP35, 50VHA
PUHZ-RP60, 71VHA
PUHZ-RP100-140VHAPUHZ-RP100-140YHA
<Table 4> Required additional charge when the pipe size is larger than the standard diameter
[9.52
[12.7
[12.7
RP35, 50
RP60, 71
RP100-140
Liquid pipe dia Chargeless
30m
30m
50m
60 g per 1 m longer than 20 m
100 g per 1 m longer than 20 m
100 g per 1 m longer than 20 m
20m
20m
20m
Max. pipe length Refrigerant amount to be added
OCS01-3.qxp 05.5.16 10:09 AM Page 74
75
(c) Capacity correctionCooling and heating capacity is lowered according to pipe length. Capacity can be obtained by referring to the capacity curves below. When the diameter of gas pipe is one size smaller than standard diameter, cooling capacity is lowered com-paring to the standard diameter. The lowered capacity can be obtained by referring to capacity curves for gas pipe which is one size smaller than standard size.
Corrected pipe length (m) = actual pipe length (m) + number of bends x 0.3 (m)
11 Capacity curves for PUHZ-RP • HA model <Standard size>
22 Capacity curve for PUHZ-RP35, 50 models<When gas pipe is one size smaller than standard size>
Cooling
Heating100
95
90
85
80
75
705 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80
Note: The permitted pipe length is up to 55m for RP35, 50, 60, 71 model.
Cooling RP71 model
Cooling RP35, 60 models
Cooling RP50, 100 models
Heating RP35, 50, 60, 71, 100, 125 and 140 models(Up to 55m for RP35, 50, 60, 71 model)
Cooling RP125 model
Cooling RP140 model
Cap
acity
rat
io [%
]
Corrected pipe length
5 10 15 20 25 30 35 40 45 50 5580
Cap
acity
rat
io [%
]
Corrected pipe length
85
90
95
100
Heating RP35, RP50
Cooling RP35
Cooling RP50
OCS01-3.qxp 05.5.16 10:09 AM Page 75
76
44 When gas pipe is one size larger than standard size for PUHZ-RP100, 125 and 140.1 Capacity can be obtained by referring to capacity curves of standard size.
33 Capacity curve for PUHZ-RP60, 71 models<When gas pipe is one size smaller than standard size>
(2) Adjusting the amount of refrigerantCheck additional refrigerant charging amount referring to table 7 when the liquid pipe diameter is larger thanthe standard size, and table 2 when the pipe of the standard diameter is used.
<Table 2>
<Table 1> Maximum pipe length (RP200·RP250)
Note : The maximum pipe length is 80m in case of new piping. w1 Be sure to use hard (tempered) one for pipe over [22.2.(Do not use soft (annealed) one.) w2 When using [31.75 pipe, the outdoor temperature range (dry-bulb temperature) for heating operation is -11 to +21:.
70m[30m]
SW
SW : When the outdoor unit is located lower than the indoor unit, set DIP SW8-1 on the outdoorunit controller board to ON.
<Marks in the table above>
The maximum pipe lengthCharge-less pipe length
: It can be used.: Cooling capacity is lowered. Refer to <Table6> : Additional refrigerant charge is required when the pipe length exceeds 20m. Refer to <Table7>
Liquid
pipe
(mm)gas
pipe
(mm)
OD
Thick-
ness
OD
Thick-
ness
RP200
RP250
[9.52
t0.8
[12.7
t0.8
[15.88
t1.0
[19.05
t1.0
20m
[20m]
20m
[20m]
[22.2
t1.0
50m
[30m]
50m
[30m]
[25.4
t1.0
Normal piping
70mw1
[30m]
70m
[30m]
[28.58
t1.0
SW
70m
[30m]
70m
[30m]
[19.05
t1.0
20m
[20m]
20m
[20m]
[22.2
t1.0
50m
[30m]
50m
[30m]
[25.4
t1.0
70m
[30m]
70m
[30m]
[22.2
t1.0
50m
[20m]
50m
[20m]
[25.4
t1.0
50m
[20m]
50m
[20m]
[28.58
t1.0
SW
50m
[20m]
50m
[20m]
[28.58
t1.0
SW
70m
[30m]
Nomal piping
70mw1
[30m]
[31.75
t1.0
w2
SW
50m
[20m]
w2
50m
[20m]
Amount of additional refrigerant charge (kg)
30 m and less 31-40 m and less 41-50 m and less 51-60 m and less 61-70 m and less 71-120 m and less
0.9 kg 1.8 kg 2.7 kg 3.6 kg
1.2 kg 2.4 kg 3.6 kg 4.8 kg
Outdoor unit permittedpipe length
RP200
RP250120m or less
At time of shipping(kg)
10.5
10.5No additional
charge necessary
The additional charge amount is obtained by the following formula.
Main piping:Liquid line size[9.52 overall length [m]o 0.09 [kg/m]
Main piping:Liquid line size[12.7 over all length [m]o 0.12 [kg/m]
–=
Additional charge amountfor 70 m
RP200 3.6 kgRP250 4.8 kg
+ + +
Calculate the additional charge amount based on the following procedure.If the calculation results in an amount that is smaller than the "Additional charge amount for 70m," perform the additional charge using the amount shown in "Additional charge amount for 70m."
•If the wiring connecting the indoor and outdoor units is longer than 80m. use separate indoor /outdoor unit power supplies.
OCS01-3.qxp 05.5.16 10:09 AM Page 77
78
(3) Capacity correctionCooling and heating capacity is lowered according to the piping length. Capacity can be obtained by referring to the following capacity curves.When the diameter of the gas pipe is smaller than the standard size, cooling capacity is lowered comparing tothe operation using the standard diameter pipe.The lowered capacity can be obtained by referring to the capacity curves for gas pipe which is one or two sizesmaller than standard size.Corrected pipe length (m) = actual pipe length (m) + number of bends o 0.3 (m)
1. Capacity curves 1 <Standard size>
2. Capacity curves 2 <When the gas pipe's diameter is one-size-smaller than the standard size>
3. Capacity curves 3 <When the gas pipe's diameter is two-size-smaller than the standard size>
w1 The maximum pipe length is 80m in case of new pipping.w2 When using [31.75 pipe, the outdoor temperature range (dry-bulb temperature) for heating operation is -11 to +21:.
w1 The maximum pipe length is 80m in case of new pipping. w2 When using [31.75 pipe, the outdoor temperature range (dry-bulb temperature) for heating operation is -11 to +21:.
w1 The maximum pipe length is 80m in case of new pipping. w2 When using [31.75 pipe, the outdoor temperature range (dry-bulb temperature) for heating operation is -11 to +21:.
Maximum pipe length (Main pipe[A]+Branch pipe diameter [ B and C ])
Maximum pipe length (Main pipe [A] + Branch pipe [ B, C and D ])
Maximum pipe length (Main pipe[A]+Branch pipe [ B, C, D and E ])
Main pipe(mm)[A]
Main pipe(mm)[A]
Main pipe(mm)[A]
Branch pipe
[mm] [B, C]
Branch pipe
[mm] [B, C, D]
Branch pipe
[mm] [B, C, D, E]
70m[30m]
SW
SW : When the outdoor unit is located lower than the indoor unit, set DIP SW8-1 on the outdoorunit controller board to ON.
<Marks in the table above>
The maximum pipe lengthCharge-less pipe length
: It can be used.: Cooling capacity is lowered. Refer to <Table6> : Additional refrigerant charge is required when the pipe length exceeds 20m. Refer to <Table7>
8-2-2. SYNCHRONIZED TWIN, TRIPLE AND QUADRUPLE SYSTEM(1) Synchronized twin
(2) Synchronized triple
(3) Synchronized quadruple
OCS01-3.qxp 05.5.16 10:09 AM Page 79
80
OD(mm)
Pipe diameter and thickness
[6.35
0.8
Be sure to use hard (tempered) one for pipe over [22.2.(Do not use soft (annealed) one.)
0.8 0.8 1.0 1.0 1.0 1.0 1.0
[9.52 [12.7 [15.88 [19.05 [22.2 [25.4 [28.58
1.1
[31.75
Thickness(mm)
1
4 Number of pipe bendsWithin 15 points8 points between main pipe A and each branch pipe (B, C, D, E).
2
3 Distance between indoor and indoor unitspipe length. Max. 8m
B—C B—D B—E C—D C—E D—E
1 Indoor unit
2 Outdoor unit
3 Main piping
4 Branch piping
5 Multi disttibutionpipe (option)
E
A
1
B C
1
44
4
3
5
2
2
Height difference (Indoor unit-Outdoor unit) Max. 40 m
<Table 6> Lowered cooling capacity by the smaller gas pipe diameter
5m and less6~10m11~20m21~30m31~40m41~50m
100%100~96%96~91%91~86%86~83%83~80%
100%100~91%91~81%
Pipe lengthgas pipe [22.2 gas pipe [19.05
RP250 Cooling capacity ratioRP200 Cooling capacity ratio
100%100~98%98~94%94~91%91~88%88~86%
100%100~95%95~88%
gas pipe [25.4 gas pipe [22.2
<Table 7> Additional refrigerant amount when the liquid pipe of the larger diameter is used. (Single /Simultaneous Twin / Simultaneous Triple / Simultaneous Quadruple)
If the calculation produces a negative number (i.e. a "minus" charge), additional charging is not necessary.( W [ 0)
Permissible total A+B or A+C Charge-lessOutdoor unit piping length or piping length
A+B+C+D+E A+D or A+E A+B+C+D+ERP200
120 m and less 100 m and less 30 m and lessPR250
B-C or B-D orOutdoor unit B-E or C-D or
Number of pipe bends
C-E or D-E RP200
8 m and less Within 15RP250
OCS01-3.qxp 05.5.16 10:09 AM Page 80
81
1. Perform refrigerant piping connections for the indoor / outdoor unit while the outdoor unit's stopvalve is completely closed (factory setting), and then vacuumize the refrigerant lines through the service port of the outdoor unit.
2. Open the stop valves of the outdoor unit completely.This will completely connects the refrigerant lines of the indoor and outdoor units.Handling of the stop valve is shown on the outdoor unit.
Note :· Apply refrigerating machine oil over the flare seat surface. Do not apply to the threaded portion.(It will cause the flare nut to loosen.)
· Use two wrenches to tighten piping connection.· Use leak detector or soapy water to check for gas leaks after connections are completed.· For the insulation of the connection at the indoor side, make sure to use the attached insulation materials and
thoroughly follow the instruction shown in the manual.· Always use a non-oxidizing brazing material when brazing the pipes.
Adjusting the amount of refrigerantCheck additional refrigerant charging amount referring to the procedure 2 below when the liquid pipe diameter of the main piping A is larger than the standard size.1 When the standard diameter pipe is used for the main piping A, calculate the additional refrigerant amount by
referring to <Table 2> as well as the 1:1 system.2 When the liquid pipe diameter of the main piping A is one size larger than the standard size:
· When the extension pipe length (main piping + branch piping) does not exceeds 20m, adjustment of the refrigerant is not necessary (charge-less).
· When the extension pipe length (main piping + branch piping) exceeds 20m, charge the amount of refrigerant that is obtained by the formula shown in <Table 7>.
If the calculation produces a negative number (i.e. a "minus" charge), additional charging is not necessary.Note: Apply 0 to L1 to L3 corresponding to the piping that are not used.
Correcting the capacity valueWhen calculating the lowered capacity by the extension pipe length, use the longest length between the indoor and the outdoorunits.
A+B+C+DAmount of additional refrigerant charge (kg)
30 m and less 31-40 m and less 41-50 m and less 51-60 m and less 61-70 m and less 71-120 m and less
0.9 kg 1.8 kg 2.7 kg 3.6 kg
1.2 kg 2.4 kg 3.6 kg 4.8 kg
Outdoor unit permittedpipe length
RP200
RP250120m or less
At time of shipping(kg)
10.5
10.5No additional
charge necessary
The additional charge amount is obtained by the following formula.
Main piping:Liquid line size[9.52 overall length 0.09 (Gas line:[28.58)
Main piping:Liquid line size[12.7 overall length 0.12
–=
Additional charge amountfor 70 m
RP200 3.6 kgRP250 4.8 kg
When the total length of the piping exceeds 70 m, calculate the amount of additional charge based on the following requirements.Note: If the calculation produces a negative number (i.e. a “minus” charge), of if calculation results in an amount that is less than the “Additional charge amount for 70 m,”perform the additional charge using the amount shown in “Additional charge amount for 70 m.”
The air coverage range is the value up to the position where the air speed is 0.25m/sec. when air is blown out horizontally fromthe unit at the Hi notch position.The coverage range should be used only as a general guideline since it varies according to the size of the room and the furni-ture inside the room.
OCS01-3.qxp 05.5.16 10:09 AM Page 82
83
9-2. PLA-RP·AA9-2-1. FRESH AIR INTAKE AMOUNT
OCS01-3.qxp 05.5.16 10:09 AM Page 83
84
OCS01-3.qxp 05.5.16 10:09 AM Page 84
85
9-2-2. BRANCH DUCT (Installation at site)
OCS01-3.qxp 05.5.16 10:09 AM Page 85
86
Branch duct air flow rate/static pressure characteristicsPLA-RP35AA
4-way air flow (horizontal vane) Rectangular duct 4-way air flow (horizontal vane) Round duct
3-way air flow (horizontal vane) Rectangular duct 3-way air flow (horizontal vane) Round duct
2-way air flow (horizontal vane) Rectangular duct 2-way air flow (horizontal vane) Round duct
OCS01-3.qxp 05.5.16 10:09 AM Page 86
87
PLA-RP50AAPLA-RP60AA
4-way air flow (horizontal vane) Rectangular duct 4-way air flow (horizontal vane) Round duct
3-way air flow (horizontal vane) Rectangular duct 3-way air flow (horizontal vane) Round duct
2-way air flow (horizontal vane) Rectangular duct 2-way air flow (horizontal vane) Round duct
OCS01-3.qxp 05.5.16 10:09 AM Page 87
88
30
20
10
01 2 3 4 5 6
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low
30
20
10
01 2 3 4 5 6
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low
30
40
50
60
20
10
01 2 3 4 5 6 7 8 9
Air flow rate [m3/min]
High
Low
Sta
tic p
ress
ure
[Pa]
30
40
50
60
20
10
01 2 3 4 5 6 7 8 9
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low
30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7 8 9 10 11
Air flow rate [m3/min]
High
Low
Sta
tic p
ress
ure
[Pa]
30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7
Air flow rate [m3/min]
High
Low
Sta
tic p
ress
ure
[Pa]
PLA-RP71AA
4-way air flow (horizontal vane) Rectangular duct 4-way air flow (horizontal vane) Round duct
3-way air flow (horizontal vane) Rectangular duct 3-way air flow (horizontal vane) Round duct
2-way air flow (horizontal vane) Rectangular duct 2-way air flow (horizontal vane) Round duct
OCS01-3.qxp 05.5.16 10:09 AM Page 88
89
30
40
50
20
10
01 2 3 4 5 6 7 8 9 10
Air flow rate [m3/min]
Low
High
Sta
tic p
ress
ure
[Pa]
30
40
50
20
10
01 2 3 4 5 6 7 8 9 10
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low
30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14
Air flow rate [m3/min]
High
Low
Sta
tic p
ress
ure
[Pa]
30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14
Air flow rate [m3/min]
Low
Sta
tic p
ress
ure
[Pa]
High
30
40
50
60
70
80
90
100
110
120
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low30
40
50
60
70
80
90
100
110
120
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air flow rate [m3/min]
Low
Sta
tic p
ress
ure
High
PLA-RP100AA
4-way air flow (horizontal vane) Rectangular duct 4-way air flow (horizontal vane) Round duct
3-way air flow (horizontal vane) Rectangular duct 3-way air flow (horizontal vane) Round duct
2-way air flow (horizontal vane) Rectangular duct 2-way air flow (horizontal vane) Round duct
OCS01-3.qxp 05.5.16 10:09 AM Page 89
90
30
40
50
20
10
01 2 3 4 5 6 7 8 9 10
Air flow rate [m3/min]
Low
High
Sta
tic p
ress
ure
[Pa]
30
40
50
20
10
01 2 3 4 5 6 7 8 9 10
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low
30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14
Air flow rate [m3/min]
Sta
tic p
ress
ure
[Pa]
High
Low 30
40
50
60
70
80
90
100
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14
Air flow rate [m3/min]
High
Low
Sta
tic p
ress
ure
[Pa]
30
40
50
60
70
80
90
100
110
120
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air flow rate [m3/min]
High
LowSta
tic p
ress
ure
[Pa]
30
40
50
60
70
80
90
100
110
120
20
10
01 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air flow rate [m3/min]
Sta
tic p
ress
ure[
Pa]
High
Low
PLA-RP125AAPLA-RP140AA
4-way air flow (horizontal vane) Rectangular duct 4-way air flow (horizontal vane) Round duct
3-way air flow (horizontal vane) Rectangular duct 3-way air flow (horizontal vane) Round duct
2-way air flow (horizontal vane) Rectangular duct 2-way air flow (horizontal vane) Round duct
OCS01-3.qxp 05.5.16 10:09 AM Page 90
91
9-2. PEAD-RP·EA, GA9-2-1. FAN PERFORMANCE AND CORRECTED AIR FLOW
Fan Performance <30Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)86 10 12 14 16 10 12 14 16 18 20
20
40
60
80
100
0.8
0.9
1.0
1.1
Corrected Air Flow Capacityinput
Cooling
Air flow (CMM)
Cor
rect
ion
fact
or
Fan Performance <70Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)10 126 8 14 16 18
8 10 12 14 16 1820
40
60
80
100
120
140
0.8
0.9
1.0
1.1
1.2
1.3Heating
Air flow (CMM)
Cor
rect
ion
fact
or
PEAD-RP35EA
PEAD-RP50EAFan Performance <30Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)6 8 10 12 14 16 18 20
8 10 12 14 16 18 20 2220
40
60
80
100
120
140
0.8
0.9
1.0
1.1
Corrected Air Flow Capacityinput
Cooling
Air flow (CMM)
Cor
rect
ion
fact
or
Fan Performance <70Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)8 10 12 14 16 18 20 22
8 10 12 14 16 18 20 2220
40
60
80
100
120
140
160
0.8
0.9
1.0
1.1
1.2
1.3Heating
Air flow (CMM)
Cor
rect
ion
fact
or
OCS01-4.qxp 05.5.16 10:13 AM Page 91
92
PEAD-RP60EA
PEAD-RP71EA
Fan Performance <30Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)8 10 12 14 16 18 20 22 24
12 14 16 18 20 22 24 2620
40
60
80
100
120
0.8
0.9
1.0
1.1
Corrected Air Flow Capacityinput
Cooling
Air flow (CMM)
Cor
rect
ion
fact
or
Fan Performance <70Pa>
Ext
erna
l sta
tic p
ress
ure
(Pa)
(1P
a
0.1
mm
Aq)
Air Flow (CMM)10 12 14 16 18 20 22 24 26
12 14 16 18 20 22 24 2620
40
60
80
100
120
140
0.8
0.9
1.0
1.1
1.2
1.3Heating
Air flow (CMM)
Cor
rect
ion
fact
or
LoHi
140
120
100
200
180
160
80
60
40
20
12 16 20 24 28 32
Air f low (CMM)
Fan performance <130Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)
140
120
100
180
160
80
60
40
20
12 16 20 24 28 32
Air f low (CMM)
Fan performance <70Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)=
LoHi
Corrected Air Flow CapacityInput
1.1
1.0
0.9
0.8
12 16 20 24 28 32
Air flow (CMM)
Cor
rect
ion
fact
or
Cooling
=
1.1
1.0
1.3
1.2
0.9
0.812 16 20 24 28 32
Air flow (CMM)
Cor
rect
ion
fact
or
Heating
OCS01-4.qxp 05.5.16 10:13 AM Page 92
93
PEAD-RP100EA
PEAD-RP125EA
Lo
Hi
140
120
100
200
180
160
80
60
40
20
26 28 30 32 34 36 38 40Air f low (CMM)
Fan performance <130Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q) 140
120
100
200
220
180
160
80
60
40
20
24 26 28 30 32 34 36 38 Air f low (CMM)
Fan performance <70Pa>Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)
Lo
Hi
Corrected Air Flow CapacityInput
1.1
1.0
0.9
0.824 26 28 30 32 34 36 38 40
Air flow (CMM)
Cor
rect
ion
fact
or
Cooling1.1
1.0
1.2
0.9
0.824 26 28 30 32 34 36 38 40
Air flow (CMM)
Cor
rect
ion
fact
or
Heating
= =
Lo
Hi
140
120
100
200
220
180
160
80
60
40
20
32 34 36 38 40 42 44 46 48Air f low (CMM)
Fan performance <130Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q) 140
120
100
200
220
180
160
80
60
40
20
32 34 36 38 40 42 44 46 Air f low (CMM)
Fan performance <70Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)
Lo
Hi
Corrected Air Flow CapacityInput
1.1
1.0
0.9
0.832 34 36 38 40 42 44 46 48
Air flow (CMM)
Cor
rect
ion
fact
or
Cooling1.1
1.0
1.2
0.9
0.832 34 36 38 40 42 44 46 48
Air flow (CMM)
Cor
rect
ion
fact
or
Heating
= =
OCS01-4.qxp 05.5.16 10:13 AM Page 93
94
PEAD-RP140EA
1.2
1.1
1.0
0.9
0.836 38 40 42 44 46 48 50 52
Air flow (CMM)
Cor
rect
ion
fac
tor
HeatingCorrected Air Flow CapacityInput
1.1
1.0
0.9
0.836 38 40 42 44 46 48 50 52
Air flow (CMM)
Cor
rect
ion
fac
tor
Cooling
LoHi
200
180
160
140
120
100
80
60
40
20
36 38 40 42 44 46 48 50Air f low (CMM)
Fan performance <70Pa>Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)=
Lo
200
220
180
160
140
120
100 80
60
40
20
36 38 40 42 44 46 48 50 52
Air f low (CMM)
Fan performance <130Pa>
Recommended range
Ext
erna
l st
atic
pre
ssur
e (P
a)
(1P
a
0.1m
mA
q)= Hi
OCS01-4.qxp 05.5.16 10:13 AM Page 94
95
PEAD-RP60GA
PEAD-RP71GA
OCS01-4.qxp 05.5.16 10:13 AM Page 95
96
PEAD-RP100GA
OCS01-4.qxp 05.5.16 10:13 AM Page 96
97
9-3.PEA-RP·EAFAN PERFORMANCE AND CORRECTED AIR FLOW
Air flow (CMM)
Recommended range
200
150
100
50
Hi
Lo
02015 17 25 30 35
Ext
erna
l sta
tic p
ress
ure(
Pa)
(1P
a =
0.1
mm
Aq)
Fan Performance
Corrected Air flow
1.05
0.95
1.0
0.917 20 25 30
Cor
rect
ion
fact
or
CapacityInputCooling
Air flow (CMM)
1.05
1.15
1.1
0.95
1.0
1.2
17 20 25 30C
orre
ctio
n fa
ctor
Heating
Air flow (CMM)
(1) PEA-RP71EA
(2) PEA-RP100EA
Air flow (CMM)
Recommended range
200
150
100
50
Hi
Lo
0302320 25 35 40
Ext
erna
l sta
tic p
ress
ure(
Pa)
(1P
a =
0.1
mm
Aq)
Fan Performance
Corrected Airflow
1.05
0.95
1.0
0.92320 25 30 35 40
Cor
rect
ion
fact
or
CapacityInput
Cooling
Air flow (CMM)
1.05
1.1
1.15
0.95
1.0
2320 25 30 35 40
Cor
rect
ion
fact
or
Heating
Air flow (CMM)
OCS01-4.qxp 05.5.16 10:13 AM Page 97
98
(3) PEA-RP125EA
(4) PEA-RP140EA
Air flow (CMM)
Recommended range
200
150
100
50
Hi
Lo
0352825 30 40 5045
Ext
erna
l sta
tic p
ress
ure(
Pa)
(1P
a =
0.1
mm
Aq)
Fan Performance
Corrected Air flow
1.05
0.95
1.0
0.93028 35 40 45 50
Cor
rect
ion
fact
or
CapacityInput
Cooling
Air flow (CMM)
0.95
1.0
1.1
1.05
1.15
3028 35 40 45 50C
orre
ctio
n fa
ctor
Heating
Air flow (CMM)
Air flow (CMM)
200
150
100
50
HiLo
035 4544 55 65 75
Ext
erna
l sta
tic p
ress
ure(
Pa)
(1P
a =
0.1
mm
Aq)
Fan Performance
Recommended range
Corrected Air flow
Cooling
Heating
Cor
rect
ion
fact
orC
orre
ctio
n fa
ctor
Air flow (CMM)Capacityinput
Air flow (CMM)
From the previous page.
OCS01-4.qxp 05.5.16 10:13 AM Page 98
99
9-4.PEH-RP·MYA
[1] Capacity/Input Ratio against Changes in Room Airflow Rate•Model PEH-RP200MYA
•Model PEH-RP250MYA
[2] Airflow Characteristic Curves
50 55 60 65 70
Cap
acity
/Inpu
t rat
io
Airflow rate (m3/min)
1.0
1.05
0.95
Cooling
Cap
acity
/Inpu
t rat
io
Heating
Airflow rate (m3/min)50 55 60 65 70
1.0
1.05
0.95
Input
Capacity
Capacity
Input
Cap
acity
/Inpu
t rat
io
Heating
Airflow rate (m3 /min)70 75 80 85 90
1.0
1.05
0.95
Capacity
Input
Cap
acity
/Inpu
t rat
io
Cooling
Airflow rate (m3 /min)70 75 80 85 90
1.0
1.05
0.95
Capacity
Input
Ext
erna
l sta
tic p
ress
ure
(Pa)
40 50 60 70 80
50
0
200
Operating airflow range
Airflow rate (m3/min)
100
150
220
Ext
erna
l sta
tic p
ress
ure
(Pa)
60 70 80 90 100
50
0
200
Operating airflow range
Airflow rate (m3/min)
100
150
220
PEH-RP200MYA PEH-RP250MYA
OCS01-4.qxp 05.5.16 10:13 AM Page 99
100
PLA-RP35AA PLA-RP50AAPLA-RP60AA
NOTCH SPL(dB) LINEHigh
Medium1Medium2
Low
HighMedium1Medium2
Low
31292827
NOTCH SPL(dB) LINE33312928
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
BAND CENTER FREQUENCIES, Hz
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
BAND CENTER FREQUENCIES, Hz
PLA-RP71AA PLA-RP100AANOTCH SPL(dB) LINE
34323028
NOTCH SPL(dB) LINE41393633
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
BAND CENTER FREQUENCIES, Hz
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
BAND CENTER FREQUENCIES, Hz
HighMedium1Medium2
Low
HighMedium1Medium2
Low
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
10 NOISE CRITERION CURVES
OCS01-4.qxp 05.5.26 10:48 AM Page 100
101
PLA-RP125AA PLA-RP140AANOTCH SPL(dB) LINE
45434037
NOTCH SPL(dB) LINE45434037
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
OC
TA
VE
BA
ND
SO
UN
D P
RE
SS
UR
E L
EV
EL
, dB
(0
dB
= 0
.000
2 µb
ar)
BAND CENTER FREQUENCIES, Hz
90
80
70
60
50
40
30
20
1063 125 250 500 1000 2000 4000 8000
APPROXIMATETHRESHOLD OFHEARING FORCONTINUOUSNOISE
NC-60
NC-50
NC-40
NC-30
NC-20
NC-70
BAND CENTER FREQUENCIES, Hz
HighMedium1Medium2
Low
HighMedium1Medium2
Low
UNIT
1.5m
MICROPHONE
CEILING
OCS01-4.qxp 05.5.16 10:13 AM Page 101
102
PEAD-RP35EA
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
HighLow
HighLow
Approximate minimum audible limit on continuous noise
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
HighLow
HighLow
HighLow
HighLow
Approximate minimum audible limit on continuous noise
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
Approximate minimum audible limit on continuous noise
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
Approximate minimum audible limit on continuous noise
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
Approximate minimum audible limit on continuous noise
NC60
NC50
NC40
NC30
NC20
70
60
50
40
30
20
63 125 250 500 1000 2000 4000 8000
10
0OC
TA
VE
BA
ND
PR
ES
SU
RE
LE
VE
L (d
B)
0dB
= 2
0µP
a
OCTAVE BAND CENTER FREQUENCIES (Hz)
Approximate minimum audible limit on continuous noise