No. 00ZUX108U/SME FACSIMILE UX-108 UX-178 UX …diagramas.diagramasde.com/audio/UX108U.pdfUdskiftning må kun ske med batteri af samme fabrikat og type. ... 9600 bps with automatic

1 - 1

UX-108U/178U/188UFO-375U

No. 00ZUX108U/SME

CHAPTER 1. GENERAL DESCRIPTION[1] Specifications ............................................ 1-1[2] Operation panel ......................................... 1-2[3] Transmittable documents .......................... 1-3[4] Installation ................................................. 1-4[5] Quick reference guide ............................... 1-7

CHAPTER 2. ADJUSTMENTS[1] Adjustments ............................................... 2-1[2] Diagnostics and service soft switch .......... 2-2[3] Troubleshooting...................................... 2-17[4] Error code table....................................... 2-18

CHAPTER 3. MECHANISM BLOCKS[1] General description .................................. 3-1[2] Disassembly and assembly procedures ....................................... 3-3

CHAPTER 4. DIAGRAMS[1] Block diagram ............................................4-1[2] Wiring diagram .......................................... 4-2[3] Point-to-point diagram ............................... 4-3

CHAPTER 5. CIRCUIT DESCRIPTION[1] Circuit description ...................................... 5-1[2] Circuit description of control PWB..............5-2[3] Circuit description of TEL/LIU PWB .......... 5-8[4] Circuit description of power supply PWB ............................ 5-11[5] Circuit description of CIS unit ................... 5-11

CHAPTER 6. CIRCUIT SCHEMATICS ANDPARTS LAYOUT[1] Control PWB circuit ................................... 6-1[2] TEL/LIU PWB circuit ................................. 6-9[3] Power supply PWB circuit ....................... 6-11[4] Operation panel PWB circuit ................... 6-13

CHAPTER 7. OPERATION FLOWCHART[1] Protocol ..................................................... 7-1[2] Power on sequence .................................. 7-2

CHAPTER 8. OTHERS[1] Service tools .............................................. 8-1[2] IC signal name .......................................... 8-3PARTS GUIDE

CONTENTS

FACSIMILE

UX-108UX-178UX-188

MODEL FO-375

Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones formaintaining the safety and performance of the set.

This document has been published to be usedfor after sales service only.The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

Non Cutter model Cutter model

UX-108 UX-178/188

FO-375Illustration: UX-108

1 – 2

UX-108U/178U/188UFO-375U

(Danish) ADVARSEL !Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.Levér det brugte batteri tilbage til leverandoren.

(English) Caution !Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent typerecommended by the equipment manufacturer.

Discard used batteries according to manufacturer’sinstructions.

(Finnish) VAROITUSParisto voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaantyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French) ATTENTIONIl y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie dumême type ou d’un type recommandé par le constructeur.Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

(Swedish) VARNINGExplosionsfare vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalenttyp som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantensinstruktion.

(German) AchtungExplosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ odervom Hersteller empfohlene Batterien verwendet werden.Entsorgung der gebrauchten Batterien nur nach den vom

Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY REPLACEMENT

1 – 1

UX-108U/178U/188UFO-375U

CHAPTER 1. GENERAL DESCRIPTION

[1] SpecificationsAutomatic dialing: Rapid Key Dialing: 10 numbers

Speed Dialing: 20 numbers

Fax paper: Initial starter roll (included with faxmachine): 49 ft. (10 m) roll

Recommended replacement roll: FO-40PRw 164 ft. (50 m) roll

Automatic document feeder: 10 sheets max.

Paper cutting method: UX-108: Tear off by handUX-178/188/FO-375: Automatic cutter

Modem speed: 9600 bps with automatic fallback to7200, 4800, or 2400 bps

Transmission time* : Approx. 15 seconds (Sharp special mode)

Display: 16-digit LCD display

Reception modes: Auto/Manual/Answering machine(for connecting answering machine)

Resolution: Horizontal:203 pels/inch (8 dots/mm)

Vertical:Standard: 98 lines/inch(3.85 lines/mm)Fine/Halftone: 196 lines/inch(7.7 lines/mm)Super fine: 391 lines/inch(15.4 lines/mm)

Recording system: Thermal recording

Halftone (grayscale): 64 levels

Applicable telephone line: Public switched telephone network

Compatibility: ITU-T (CCITT) G3 mode

Configuration: Half-duplex, desktop transceiver

Compression scheme: MH, MR, Sharp special mode

Scanning method: Sheet-feeder CIS (Contact Image Sensor)

Effective recording width: 8.3" (210 mm) max.

Input document size: Automatic feeding:Width 5.8 to 8.5"

(148 to 216 mm)Length 5.5 to 11"

(140 to 279 mm)Manual feeding:

Width 5.8 to 8.5"(148 to 216 mm)

Length 5.5 to 23.6"(140 to 600 mm)

Effective scanning width: 8.3" (210 mm) max.

Contrast control: Automatic/Dark selectable

Copy function: Standard

Telephone function: Standard(cannot be used if power fails)

Power requirements: 120 V AC, 60 Hz

Operating environment: 41 to 95°F (5 to 35°C)

Humidity: Maximum: 85 %

Power consumption: Stand-by: 5.0 W

Maximum: 100 W

Dimensions: Width: 12.1" (308 mm)

Depth: 10.4" (256 mm)

Height: 5.4" (138 mm)

Weight: UX-108: Approx. 5.5 lbs. (2.5 kg)

UX-178/UX-188/FO-375: Approx. 5.7 lbs. (2.6 kg)

* Based on ITU-T (CCITT) Test Chart #1 at standard resolution in Sharpspecial mode, excluding time for protocol signals (i.e., ITU-T phase Ctime only).

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procductimprovement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be somedeviation from these values in individual units.

1 – 2

UX-108U/178U/188UFO-375U

[2] Operation panel

11 12 13 14108 9

1 4 5 62 3

TEL FAX

RECEPTIONMODE RESOLUTION FUNCTION

DOWN VOLUME UP

A.M.

SPEED DIAL

REDIAL

SPEAKER

1 2

3 4

5 6

7 8

9 10/POLL

15

7

ABC DEF

JKL MNOGHI

TUV WXYZPQRS

SYMBOL

START

STOP

COPY/HELP

SEARCH

R

TEL/FAX

1. Display This displays various messages during operation and programming.2. PANEL RELEASE Pull this release toward you to open the operation panel.3. RECEPTION MODE key Press this key to select the reception mode. An arrow in the display will point to the currently selected reception mode.4. FUNCTION key Press this key to select various special function.5. RESOLUTION key Press this key to adjust the resolution and contrast before sending or copying a document.6. VOLUME keys Press these keys to adjust the volume of the handset when the handset is lifted, the volume of the speaker when the SPEAKER key has been pressed, or the volume of the ringer at all other times.7. STOP key Press this key to stop operation before they are completed.8. Number keys Use these keys to dial numbers, and enter number and letters during number/name storing procedures.9. SPEED DIAL key Press this key to dial a 2-digit Speed Dial number.

10. REDIAL key Press this key to automatically redial the last number dialed.11. SPEAKER key Press this key to hear the line and fax tones through the speaker when sending a document. Note: This is not a speakerphone. You must pick up the handset to talk with the other party.12. HOLD/SEARCH key Press this key to search for an automatic dialing number, or, during a phone conversation, press this key to put the other party on hold.13. Rapid Dial keys Press one of these keys to dial a fax or voice number automatically. (Note that you must attach the Rapid Key labels.)14. START key Press this key to send or receive a document.15. COPY/HELP key When a document is in the feeder, press this key to make a copy. At any other time, press this key to print out the Help List, a quick refernce guide to the opeation of your fax.

1 – 3

UX-108U/178U/188UFO-375U

[3] Transmittable documents

1. Document Sizes

* With special sizes, only one sheet can be fed into the machine at atime. Insert next page into feeder as current page is being scanned.

2. Paper Thickness & Weight

3. Document Types• Normal paper

Documents handwritten in pencil (No. 2 lead or softer), fountain pen,ball-point pen, or felt-tipped pen can be transmitted.

Documents of normal contrast duplicated by a copying machine canalso be transmitted.

• Diazo copy (blue print)

Diazo copy documents of a normal contrast may be transmitted.

• Carbon copy

A carbon copy may be transmitted if its contrast is normal.

4. Cautions on Transmitting Documents• Documents written in yellow, greenish yellow, or light blue ink cannot

be transmitted.

• Ink, glue, and correcting fluid on documents must be dry before thedocuments can be transmitted.

• All clips, staples and pins must be removed from documents be-foretransmission.

• Patched (taped) documents should be copied first on a copier andthen the copies used for transmission.

• All documents should be fanned before insertion into the feeder toprevent possible double feeds.

Normal sizewidth 5.8" – 8.5"(148 – 216 mm)

length 5.5" – 11"(140 – 279 mm)

5. Automatic Document Feeder CapacityNumber of pages that can be placed into the feeder at anytime is asfollows:

Normal size: max. ADF 20 sheets (14 lbs – 20 lbs)

Special size: single sheet only (manual feed)

NOTES: • When you need to send or copy more pages than the feederlimit, place additional pages in feeder when last page infeeder is being scanned.

• Place additional pages carefully and gently in feeder.If force is used, double-feeding or a document jam mayresult.

6. Readable Width & LengthThe readable width and length of a document are slightly smaller thanthe actual document size.

Note that characters or graphics outside the effective document scan-ning range will not be read.

• Readable width

210 mm, max.

• Readable length

This is the length of the document sent minus 0.16" (4 mm) from the topand bottom edges.

Normal size

ADF 10sheets

2.4 x 10–3 –4.7 x 10–3

inch(0.06–0.12 mm)

Thickness

Weight0.15 x 10–3

lbs/inch2

(52–104g/m2 )

(14–28lbs)

ADF 20sheets

Thickness2.4 x 10–3

–3.5 x 10–3 inch

(0.06–0.09 mm)

Weight0.77 x 10–3

–0.11 x 10–3 lbs/inch2

(52–74.3g/m2 )(14–20lbs)

Special sizeThickness

4.7 x 10–3 –7.9 x 10–3

inch(0.12–0.20 mm)

0.15 x 10–3 –0.20 x 10–3

lbs/inch2

(52–157 g/m2)

Weight

Use document carrier sheet for smaller documents.

Readable width

0.16"(4mm)

0.16"(4mm)

Readable length

(Min.)

(Max.)Leter size

(Max.)

140mm279mm

600mm

148mm 216mm[Normal size]

216mm[Special size]

1 – 4

UX-108U/178U/188UFO-375U

7. Use of Document Carrier SheetA document carrier sheet must be used for the following documents.• Those with tears.

• Those smaller than size 5.8"(W) x 5.5"(L) (148 mm (W) x 140 mm(L)).

• Carbon-backed documents

NOTE: To transmit a carbon-backed document, insert a white sheet ofpaper between the carbon back of the document and the docu-ment carrier.

• Those containing an easily separable writing substance (e.g., trac-ing paper written on with a soft, heavy lead pencil).

NOTES: • When using the document carrier, carefully read the in-structions written on the back.

• If the document carrier is dirty, clean it with a soft, moistcloth, and then dry it before using for transmission.

• Do not place more than one document in the carrier at atime.

[4] Installation

1. Site selectionTake the following points into consideration when selecting a site for thismodel.

ENVIRONMENT

• The machine must be installed on a level surface.

• Keep the machine away from air conditioners, heaters, direct sun-light, and dust.

• Provide easy access to the front, back, and sides of the machine. Inparticular, keep the area in front of the machine clear, or the originaldocument may jam as it comes out after scanning.

• The temperature should be between 5° and 35°C.

• The humidity should be between 30% and 85% (without conden-sation).

ELECTRICITY120V, 60Hz, grounded (3-prong) AC outlet is required.

Caution!

• Connection to a power source other than that specified will causedamage to the equipment and is not covered under the warranty.

• If your area experiences a high incidence of lightning or power surges,we recommend that you install a surge protector for the power andtelephone lines. Surge protectors can be purchased at most telephonespecialty stores.

If the machine is moved from a cold to a warm place...If the machine is moved from a cold to a warm place, it is possible thatthe reading glass may fog up, preventing proper scanning of documentsfor transmission. To remove the fog, turn on the power and wait approxi-mately 2 hours before using the machine.

TELEPHONE JACKA standard RJ11C telephone jack must be located near the machine.This is the telephone jack commonly used in most homes and offices.

• Plugging the fax machine into a jack which is not an RJ11C jack mayresult in damage to the machine or your telephone system. If you donot know what kind of jack you have, or needed to have one installed,contact the telephone company.

2. Connections1Connect the handset as shown and place it on the handset rest.

♦The ends of the handset cord are identical, so they will go intoeither jack.

Use the handset to make ordinary phonecalls, or to transmit and receive docu-ments manually.

2 Plug the power cord into a 120 V, 60 Hz, grounded (3-prong) ACoutlet.

• Caution: Do not plug the power cord into any other kind of outlet.This will damage the machine and is not covered under the war-ranty.

• The machine does not have a power on/off switch, so the poweris turned on and off by simply plugging in or unplugging the powercord.

3 Insert one end of the telephone line cord into the "TEL. LINE " jack.Insert the other end into a standard (RJ11C) single-line telephonewall jack.

Be sure to insert the telephone line cord into the "TEL. LINE " jack.Do not Insert into the "TEL. SET" jack.

Direction of insertion

Make print straightacross paperE.G.Place the documentcarrier in the documentfeeder with the clear filmside down

TEL.SET TEL.LINE

1 – 5

UX-108U/178U/188UFO-375U

3. Original document support1Rotate the original document support so that it points straight out.

4. Loading the fax paper• Your fax machine prints incoming faxes on a special kind of paper

called thermal paper.

• The fax’s print head creates text and images by applying heat tothe thermal paper.

1 Pull the release marked PANEL RELEASE toward you and open theoperation panel.

2Remove the packing paper from the paper compartment.

3Unwrap the roll of fax paper and place it in the compartment.

• Important: The roll must be placed so that the leading edge ofthe paper unrolls as shown. (The paper is only coated on oneside for printing. If the roll is placed backwards, the paper willcome out blank after printing.)

YES

NO!

4 Insert the leading edge of the paper into the paper inlet. Continue topush the paper through the inlet until it comes out of the opening inthe front of the fax.

5Close the operation panel, making sure it clicks into place.

6UX-108: A short length of the fax paper will feed out. Grasp the paperby the edge and pull upward to tear it off.

UX-178/UX-188/FO-375: A short length of the fax paper will feed outand be cut off. (If this doesn’t happen, repeat the loading procedure.)

Note: The UX-178/UX-188/FO-375 has a built-in anti-curl mecha-nism that will help to reduce paper curling problems. The anti-curl mechanism is more effective at the beginning of the paperroll and less effective towards the end.

Paper inlet

The paper will reappear here. Makesure it is aligned between the arrowson each side of the guide, and thenpasses under the plate and out thefront of the fax.

1

2

Click!

1 – 6

UX-108U/178U/188UFO-375U

4. Clearing a jammed documentIf the original document doesn’t feed properly during transmission orcopying, or DOCUMENT JAMMED appears in the display, first try press-ing the START key. If the document doesn’t feed out, open the opera-tion panel and remove it.Important: Do not try to remove a document without opening the op-eration panel. This may damage the feeder mechanism.


2Remove the document.

5. Clearing jammed fax paper


2 Remove the paper roll.

• UX-178/188/FO-375: If any pieces of paper are stuck in the cut-ter, remove them with caution.

• UX-178/188/FO-375: Press the START key to reset the cutter.

3 Cut off the wrinkled part of the paper.

4 Reload the paper.

• Jammed fax paper is often caused by improper loading. Be sureto carefully follow the instructions for paper loading given in "Load-ing the Fax Paper" in Chapter 1.

5 If the display still shows PAPER JAMMED (UX-178/188/FO-375 only)

If the display still shows PAPER JAMMED after you press the STARTkey in Step 2 above, the cutter is still engaged in the cutting position.To open the cutter, turn the fax up on its rear end and insert any long,rod-like object with a flat or blunt end into the hole marked CUTTERRESET. Continue to push the rod in until you feel it move a leverinside the machine.

CUTTER

RESET

1 – 7

UX-108U/178U/188UFO-375U

[5] Quick reference guide

INSTALLATION

1. Connect the handset as shown.

2. Plug the power cord into a grounded, 120 V outlet.

3. Plug one end of the telephone line into the "TEL. LINE" jack on the rear of thefax, and the other end into your telephone wall jack.

Connecting an answering machine and/or extension telephone

1. Remove the seal covering the "TEL. SET" jack on the rear of the fax. Connectan extension telephone or answering machine to the "TEL. SET" jack.

2. If desired, connect an extension phone to the answering machine.

ENTERING YOUR NAME AND NUMBER

1. Press: FUNCTION

3

Display shows: OWN NUMBER SET

2. Press:

3. Enter your fax number (max. of 20 digits) by pressing the number keys.

♦ If you make a mistake, press the HOLD/SEARCH key to move the cursorback to the mistake, then enter the correct number or letter.

4. Press:

5. Enter your name by pressing the appropriate number keys as shown below.♦ To enter two letters in succession that require the same key, press the SPEAKER

key after entering the first letter.

TEL.SET TEL.LINE

1

3

2

TEL.SET TEL.LINE

A =

B =

C =

D =

E =

F =

G =

H =

I =

J =

K =

L =

M =

N =

O =

P =

Q =

R =

S =

T =

U =

V =

W =

X =

Y =

Z =

SPACE =

SPEED DIAL

REDIAL

HOLD/SEARCH

SPEAKER

ABC DEF

JKL MNOGHI

TUV WXYZPQRS

OPER

Deletes highlightedletter

Upper/lower caseshift key

Moves cuesor to theleft

Moves cuesor to theright

Press either key one or more times to selectand enter a symbol.

6. When finished, press:

SETTING THE DATE AND TIME

Press:

Display: DATE & TIME SET

Press the START key:

Enter two digits for the Month (01 through 12).

Enter two digits for the Day (01 through 31).

Enter four digits for the Year (EX: 1998).

Enter two digits for the Hour (01 through 12).

Enter two digits for the Minute (00 through 59).

Press the " " key for A.M. or the "#" key for P.M.

When finished, press:

STORING AND CLEARING NUMBERS FOR AUTO DIALING

1. Press:

Display shows: FAX/TEL # MODE

2. Press "1" to store a number or "2" to clear a number.

3. Enter a 2-digit Speed Dial number (from "01" to "10" for Rapid Key Dialing, or11 to 30 for Speed Dialing). (If you are clearing a number, go to Step 7.)

4. Enter the full telephone/fax number.

5. Press:

6. Enter the name of the location by pressing number keys (max. of 20 charac-ters). (Refer to the letter entry table in ENTERING YOUR NAME ANDNUMBER.)

7. Press:

SENDING DOCUMENTS

START

START

START

STOPSTART

FUNCTION

3

START

STOPSTART

Place your document (up to 20pages) face down in the docu-ment feeder.

Normal Dialing1. Lift the handset or press

2. Dial the fax number.

3. Wait for the reception tone (if a person answers, ask them to press their Startkey).

4. Press: START

Rapid Key DialingPress the appropriate Rapid Key. Transmission will begin automatically.

Speed Dialing

1. Press:

2. Enter 2-digit Speed Dial number.

3. Press:

RECEIVING DOCUMENTS

Press:

FAX mode: The fax automatically answers on four rings and receives the incomingdocument.

TEL mode:

A.M. mode: Select this mode when an answering machine is connected to the faxand the answering machine is turned on.

SPEAKER

SPEED DIAL

START

FAXTEL

A.M.

FAXTEL

A.M.

FAXTEL

A.M.

FEB 1 1998

FEB 1 1998

FEB 1 1998

RECEPTION MODE

Faxtone

START

RECEIVING

STOPSTART

FUNCTION

3

UX-108U/178U/188UFO-375U

CHAPTER 2. ADJUSTMENTS

[1] Adjustments

GeneralSince the following adjustments and settings are provided for this model,make adjustments and/or setup as necessary.

1. Adjustments

Adjustments of output voltage (FACTORY ONLY)1. Install the power supply unit in the machine.

2. Set the recording paper and document.

3. When the document is loaded, power is supplied to the output lines.Confirm that outputs are within the limits below.

Output voltage settings

(1) FU100 (ICP-S07) is installed in order to protect IC’s from an over-current generated in the motor drive circuit. If FU100 is open, replaceit with a new one.

3. Settings

(1) Dial mode selectorDIAL mode (Soft Switch No. SWB4 DATA No. 3)

Output Voltage limits+5V 4.75V ∼ 5.25V+24V 23.3V ∼ 24.7V

2. IC protectors replacementICPs (IC Protectors) are installed to protect the motor driver circuit.ICPs protect various ICs and electronic circuits from an overcurrent con-dition.

The location of ICPs are shown below:

1 DG2 +5V3 VTH-ON

4 MG5 MG6 MG7 +24V8 VTH9 VTH

10 VTH

ConnectorNo. CNPW

Pin No.

2 – 1

TEL/LIU PWB POWER SUPPLY PWB

CNLIU

CNLIUA

CN2

CNPW

CONTROL PWB

CONTROL PWB(TOP SIDE)

CNLIUA CNPW

FU100

4. Method of release of starting lock up by BatteryReset

(1) SummaryThere is a possibility of release of the lock up by reset the signal BATRSTof CPU (XFC3, XFC5), if it lock up when you turn on the power of the setin UX-108 series. We inform you of the method of release.

(2) ContentsWhen you turn on the power of the set without EPROM by your mistake,if you turn off the power after, turn on the power with EPROM again, theset don’t start.

In this case, before you judge the cpu (XFC3, XFC5) is wrong, you needto confirm the release of the lock up by reset the signal BATRST. andunknown origin in the same way.

Method of the reset of signal BATRSTShort the between leads of the capacitor C5 on the control PWB,S2915SC-70 in the state of POWER OFF.

(step 1) Select "OPTION SETTING".

KEY : FUNCTION 4

DISPLAY: OPTION SETTING PRESS OR #

(step 2) Select "DIAL MODE".

KEY:

DISPLAY: DIAL MODE 1=TONE, 2=PULSE

(step 3) Select, using "1" or "2".

KEY: 1

DISPLAY: TONE SELECTED

KEY: 2

DISPLAY: PULSE SELECTED

(step 4) End, using the "STOP" key.

KEY:

CursorWhen initially registering,the mode shows 1=TONE.When registering again, themode which was registeredformerly is shown.

STOP

# # # # # # # #

UX-108U/178U/188UFO-375U

[2] Diagnostics and service soft switch

1. Operating procedure

(1) Entering the diagnostic mode

Press FUNC → 9 → → 8 → # → 7 , and the following display will appear.

ROM Ver. FWR0 (FWS0 ) After 2 sec: DIAG MODE

FWR0 (UX-108U)

FWS0 (UX-178U/188U/FO-375U)

Then press the START key. Select the desired item with the key or the # key or select with the rapid key. Enter the mode with the START key.

(Diag•specifications)

2. Diagnostic items

ITEM DIRECTContents Function

No. key

1 1 SOFT SWITCH MODE Soft switches are displayed and changed. List can be output.

2 2 ROM & RAM CHECK ROM is sum-checked, and RAM is matched. Result list is output.

3 3 AGING MODE 10 sheets of check patterns are output every 5 minutes per sheet.

4 4 PANEL KEY TEST Panel keys are tested. Result list is output.

5 5 CHECK PATTERN MODE Check pattern is output.

6 6 SIGNAL SEND MODE Various signals of FAX communication are output.

7 7 MEMORY CLEAR MODE Back-up memory is cleared, and is set at delivery.

8 8 SHADING MODE Shading compensation is performed in this mode.

9 9 ALL BLACK MODE To check the print head, whole dots are printed over the interval of 2 m.

10 10 AUTO FEEDER MODE Insertion and discharge of document are tested.

11 − ENTRY DATA SEND Registered content is sent.

12 − ENTRY DATA RECEIVE Registered content is received, and its list is output.

13 − CUTTER AGING Recording paper is successively cut. (Cutter model only)

If the diag mode cannot be set, repeat the diag mode operation, per-forming the following operation.After the power is turned on and "WAIT A MOMENT" is indicated, pressthe STOP key.

2 – 2

FUNC DIAG MODE9 8 7

START 1Soft switch mode

START 2ROM & RAM check

START 3Aging mode

START 4Panel key test

START 5Check pattern mode

START 6Signal send mode

START 7Memory clear mode Shading mode

START

START

All black mode

START10 Auto feeder mode

START9

Entry data send

Entry data receive

START

START8

STARTKEY

STOPKEY

++"Power ON"

Memory clear(Work + Backup)

FWR0 ,FWS0

START Cutter aging(Cutter model only)

In relation with the process response (request from ProductionEngineering) "WAIT A MOMENT" clock indication may appeardepending on STOP key timing. If the STOP key is held down,"MEMORY CLEAR?" appears.

UX-108U/178U/188UFO-375U

3. Diagnostic items description

3. 1. Soft switch modeUsed to change the soft switch settings.

The soft switch which is stored internally is set by using the keys.

The available soft switches are SW-A1 to SW-L2.

The content of soft switches is shown in page 2-5 to 2-16.

The contents are set to factory default settings.

3. 2. ROM & RAM checkROM executes the sum check, and RAM executes the matching test.The result will be notified with the number of short sounds of the buzzeras well as by printing the ROM & RAM check list.Number of short sounds of buzzer 0 → No error

1 → ROM error2 → RAM error (32Kbyte)

3. 3. Aging modeIf any document is first present, copying will be executed sheet by sheet.If no document is present, the check pattern will be printed sheet bysheet. This operation will be executed at a rate of one sheet per 5min-utes, and will be ended at a total of 10 sheets.

3. 4. Panel key testThe mode is used to check whether each key operates properlyor not. Press the key on the operation panel, and the key will be dis-played on the display. Therefore, press all keys. At this time, finally pressthe STOP key.

When the STOP key is pressed, the keys which are not judged as"pressed" will be printed on the result list.

• LED port of the contact image sensor (CIS) is kept on during theterm from when start of the panel test mode to end with the STOPkey.

3. 5. Check pattern modeThis mode is used to check the status of print head. Two sheets of checkpattern are printed. The following information of check pattern is printed.

1 Vertical stripes (alternate white and black lines) Approx. 35 mm

2 Full black Approx. 70 mm

3 Full white Approx. 35 mm

3. 6. Signal send modeThe mode is used to send various signals to the circuit during FAX com-munication. Every push of START key sends a signal in the followingsequence. Moreover, the signal sound is also output to the speaker whenthe line monitor of the soft switch is on.

[1] No signal (CML signal turned on)

[2] 9600bps

[3] 7200bps

[4] 4800bps

[5] 2400bps

[6] 300bps (FLAG)

[7] 2100Hz (CED)

[8] 1100Hz (CNG)

[9] END

3. 7. Memory clear modeThis mode is used to clear the backup memory and reset to the defaultsettings.

3. 8. Shading modeThe mode is used for the shooting compensation. For reading, set upthe special original paper.

The shooting compensation memorizes the reference data of white andblack for reading.

Moreover, the memorized data is not erased even if memory clear modeis executed.

3. 9. All black modeThe mode is used to check the state of the printing head and inten-tionally overheat it. Whole dots are printed over the interval of 2 m. If it isoverheated or the printing sheet is jammed, press STOP key for the end.

3. 10. Auto feeder modeIn this mode, a document is inserted and discharged to check the autofeed function.

After this mode is started, set a document, and the document feed willbe automatically tested.

3. 11. Entry data sendThe mode is used to send the registered data to the other machine andmake the other machine copy the registered content.

Before sending in this mode, it is necessary to set the other machine atthe entry data receive mode.

The sent content is as follows. After printing is completed, the followinglists are printed.

1. Telephone list data

2. Sender register data

3. Optional setting content

4. Soft switch content

5. Junk fax number list

6. Timer reservation data (only on the model which timer reserva-tion is possible)

2 – 3

1

2

3RANK 0 or 1

Note:There is a selection RANK 0 or 1 depending on resistance value of thethermal head. RANK 0 or RANK 1 is printed at the tail of check patternto identify.

UX-108U/178U/188UFO-375U

3. 12. Entry data receiveIn this mode, the registered data sent from the other machine are re-ceived and the received data are registered in the own machine. Whenthis mode is used for receiving, the other machine must be in the entrydata send mode.

After receiving is completed, the following lists are printed.

1. Telephone list data

2. Sender register data (The passcode No. is also printed if the polingfunction is provided.)

3. Optional setting list

4. Soft switch content

5. Junk fax number list

6. Timer reservation list (only model which timer communication ispossible)

2 – 4

3. 13. Cutter aging (Cutter model only)The mode is used to continuously cut the recording paper to approx. 10mm and display the number of cutting times.

(Unless the memory clear is executed, the number of cutting times isintegrated.)

In the following cases, the operation is stopped.

1. The stop key is continuously pressed.

2. There is no recording paper.

3. The recording paper is jammed.

4. How to make soft switch settingTo enter the soft switch mode, make the following key entries in sequence.

Press FUNCTION 9 8 7 START START

Press FUNCTION key.

Press key.

Press key.

Bit1 - 8 are set.

Soft SW-A2 - SW-L2 are set.

S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A2 = 0 0 0 0 0 0 0 0

S F T SW-L2 = 0 0 0 0 0 0 0 0

Press key during setting.

To finish the settings halfway betweenSW-A1 and SW-L2, press the STOPkey. In this case, the setting being doneto the SW No. on display will be nullifiedwhile settings done to the precedingSW Nos. remain in effect.

The soft switch mode is terminated.

S F T SW-A1 = 0 0 0 0 0 0 0 0

START

DATA No. 1 2 3 4 5 6 7 8

When the COPY key is pressed, thecontents of soft switches are printed.

UX-108U/178U/188UFO-375U

5. Soft switch description

• Soft switch

1 Protect from echo No Yes 0

2 Forced 4800 BPS reception Yes No 0

3 Footer print Yes No 0

4 Length limitation of copy/send/receive No limit Copy/send: 60cm 0

Receive: 1.5m

5 CSI transmission No transmitted Transmitted 0

6 DIS receive acknowledgement during G3 Twice NSF: Once 0

transmission DIS: Twice

7 Non-modulated carrier for V29 transmission Yes No 0

modem

8 EOL detect timer 25 s 13 s 0

Modem speed V.29 V.27 ter

9600bps 7200bps 4800bps 2400bps

1 No. 1 0 0 0 0 0

2 No. 2 0 0 0 0 0

3 No. 3 0 1 1 0 0

4 No. 4 1 1 0 0 1

5 Sender’s information transmit No Yes 0

6 H2 mode No Yes 0

7 Communication error treatment in RTN No communication error Communication error 0

sending mode (reception)

8 CNG transmission No Yes 0

CED tone signal interval 1000ms 750ms 500ms 75ms

1 No. 1 1 1 0 0 0

2 No. 2 1 0 1 0 0

3 MR coding No Yes 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Signal transmission level Binary input 0

2 No. = 16 8 4 2 1 1

3 1 2 3 4 5 0

4 0 1 0 1 0 (-10 dBm) 1

5 0

6 Protocol monitor (error print) Printed at com. err Not printed 0

7 Protocol monitor Yes No 0

8 Line monitor Yes No 0

Digital line equalization setting (Reception) 7.2km 0km

1 No. 1 1 0 1

2 No. 2 1 0 1

3 Reserved 0

4 Reserved 0

Digital cable equalizer setting (Reception 7.2km 0km

5 for Caller ID) No. 5 1 0 0

6 No. 6 1 0 0

7 Error criterion 10 ~ 20 % 5 ~ 10 % 0

8 Anti junk fax check Yes No 0 OPTION

SWNO.

DATANO.

ITEMSwitch setting and function

1 0Remarks

Initialsetting

SWl

A1

SWl

A2

SWl

A3

SWl

A5

SWl

A4

2 – 5

UX-108U/178U/188UFO-375U

1 Auto gain control (MODEM) Enable Disable 1

2 End Buzzer Yes No 1

3 Disconnect the line when DIS is received in No Yes 1

RX mode

4 Equalizer freeze control (MODEM) On Off 0

5 Equalizer freeze control 7200 BPS only No Yes 0

6 CNG transmission in manual TX mode Yes No 1

7 Initial compression scheme for sharp fax in MR mode H2 mode 0

TX mode

8 Reserved 0

1 Recall interval Binary input 0 OPTION

2 No. = 8 4 2 1 1

3 1 2 3 4 0

4 0 1 0 1 (5 x 60 sec = 5 min) 1

5 Recall times Binary input 0 OPTION

6 No. = 8 4 2 1 0

7 5 6 7 8 1

8 0 0 1 0 (Twice) 0

1 Dial pausing (sec/pause) 4 sec 2 sec 0

2 Reserved 0

3 Reserved 0

4 Busy tone detection (after auto dial) No Yes 1

5 Waiting time after dialing 90 sec 45 sec 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Hold function Enable Disable 1

1 Auto Dial Mode Delay timer of before line 3 sec 0 sec 0

connect

2 Auto Dial Mode Delay timer of after line 3 sec 1.7 sec 0

connect

3 Dial mode Tone Pulse 1 OPTION

4 Pulse → Tone change function by key Enable Disable 0

5 Dial pulse make/break ratio (%) 40/60 33/67 1

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 DTMF signal transmission level (Low) Binary input 0

2 No. = 16 8 4 2 1 1

3 1 2 3 4 5 0

4 0 1 0 1 0 (0.5 x 10 = -5 dBm) 1

5 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

SWNO.

DATANO.


1 0Remarks

Initialsetting

SWl

B5

SWl

B4

SWl

B3

SWl

B2

SWl

B1

SWl

A6

2 – 6

UX-108U/178U/188UFO-375U

1 DTMF signal transmission level (High) Binary input 0

2 No. = 16 8 4 2 1 0

3 1 2 3 4 5 1

4 0 0 1 1 1 (0.5 x 7 = -3.5 dBm) 1

5 1

6 Reserved 0

7 Reserved 0

8 Reserved 0

Reading slice (Binary) Factory Light Dark Darker in

setting dark mode

1 No. 1 0 1 0 1 0

2 No. 2 0 0 1 1 0

Reading slice (Half tone) Factory Light Dark Darker in

setting dark mode

3 No. 3 0 1 0 1 0

4 No. 4 0 0 1 1 0

5 Line density selection Fine Standard 0 OPTION

6 Halftone gray scale selection 16 level 64 level 0

7 MTF correction in half tone mode No Yes 0

8 Reserved 0

1 Number of rings for auto receive Binary input 0 OPTION

2 No. = 8 4 2 1 1

3 1 2 3 4 0

4 0 1 0 0 (4 times) 0

5 Automatic switching manual to auto receive Reception after 5 rings No reception 0

mode

6 Reserved 0

7 Reserved 0

8 Reserved 0

Distinctive ringing setting No. 1 No. 2 No. 3 OPTION

Factory setting: OFF OFF 0 0 0

STANDARD 0 0 1

1 PATTERN1 0 1 0 0

2 PATTERN2 0 1 1 0

3 PATTERN3 1 0 0 0

4 Reserved 0

5 Caller ID function Yes No 0 OPTION

CI off detection timer (Distinctive ring 1200ms 1000ms 700ms 350ms

6 setting off only) No. 6 0 1 0 1 0

7 No. 7 0 0 1 1 1

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

2 – 7

SWNO.

DATANO.


1 0Remarks

Initialsetting

SWl

B6

SWl

C1

SWl

D2

SWl

D1

SWl

E1

UX-108U/178U/188UFO-375U

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

DTMF detection time 50ms 80ms 100ms 120ms

1 No. 1 0 0 1 1 0

2 No. 2 0 1 0 1 0

3 Protection of remote reception (5 ) detect Yes No 0 OPTION

4 Remote reception with GE telephone Compatible Not compatible 1

5 Remote operation code figures by external Binary input 0 OPTION

6 TEL (0~9) No. = 8 4 2 1 1

7 5 6 7 8 0

8 0 1 0 1 (5 ) 1

1 CNG detection in STAND-BY mode Yes No 1 OPTION

Number of CNG detect (AM mode) 1pulse 2pulses 3pulses 4pulses

2 No. 2 0 0 1 1 0

3 No. 3 0 1 0 1 1

Number of CNG (STAND-BY mode) 1pulse 2pulses 3pulses 4pulses

4 No. 4 0 0 1 1 0

5 No. 5 0 1 0 1 1

6 Fax signal detection after telephone mode dial Yes No 0

7 Reserved 0

8 Reserved 0

1 Quiet detect time Binary input 0 OPTION

2 No. = 8 4 2 1 1

3 1 2 3 4 0

4 0 1 0 0 (4 sec) 0

5 Quiet detect start timing Binary input 0

6 No. = 8 4 2 1 1

7 5 6 7 8 0

8 0 1 0 1 (5 sec) 1

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

Section time of quiet detection 30s 40s 50s 60s

5 No. 5 0 0 1 1 0

6 No. 6 0 1 0 1 1

7 Reserved 0

8 Reserved 0

SWl

F1

SWl

E2

SWl

F2

SWl

G1

SWl

G2

SWl

G3

SWNO.

DATANO.


1 0Remarks

Initialsetting

2 – 8

UX-108U/178U/188UFO-375U

1 Busy tone detection ON/OFF time (Lower 350ms 200ms 0

duration)

2 Busy tone detection ON/OFF time (Upper 650ms 900ms 0

duration)

3 Reserved 0

4 Busy tone continuous sound detect time 5s 10s 1

5 Reserved 0

6 Busy tone detect continuation sound detect No Yes 0

7 Reserved 0

8 Busy tone detect intermittent sound detect No Yes 0

Busy tone detection pulse number 2pulses 4pulses 6pulses 10pulses

1 No. 1 0 0 1 1 0

2 No. 2 0 1 0 1 1

3 Fax switching when A.M. full Yes No 0 OPTION

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

SWl

H1

SWNO.

DATANO.


1 0Remarks

Initialsetting

SWl

H2

SWl

I1

SWl

I2

SWl

I3

SWl

I4

2 – 9

UX-108U/178U/188UFO-375U

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Sender’s phone number setting Cannot change Change allowed 0

4 Reserved 0

5 Reserved 0

6 Day light saving setting No Yes 1 OPTION

Ringer volume Off Low Middle High OPTION

7 No. 7 0 0 1 1 1

8 No. 8 0 1 0 1 0

Speaker volume Low Low Middle High OPTION

1 No. 1 0 0 1 1 1

2 No. 2 0 1 0 1 0

3 Polling key Yes No 0 OPTION

Handset receiver volume Low Low Middle High OPTION

4 No. 4 0 0 1 1 1

5 No. 5 0 1 0 1 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

Communication results printout Error/Timer Send only Always No print OPTION

3 (Transaction report) No. 3 0 0 1 1 0

4 No. 4 0 1 0 1 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

SWl

I5

SWl

I6

SWl

I7

SWl

J1

SWl

J2

SWl

J3

SWNO.

DATANO.


1 0Remarks

Initialsetting

2 – 10

UX-108U/178U/188UFO-375U

1 Entering DIAG mode by pressing SPEED Yes No 0

key

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

1 Reserved 0

2 Reserved 0

3 Reserved 0

4 Reserved 0

5 Reserved 0

6 Reserved 0

7 Reserved 0

8 Reserved 0

SWl

K1

SWl

L1

SWl

L2

SWNO.

DATANO.


1 0Remarks

Initialsetting

2 – 11

UX-108U/178U/188UFO-375U

• Soft switch function description

SW-A1 No. 1 Protect from echo

Used to protect from echo in reception.

SW-A1 No. 2 Forced 4800BPS reception

When line conditions warrant that receptions take place at 4800 BPSrepeatedly.

It may improve the success of receptions by setting at 4800BPS.

This improve the receiving document quality and reduces handshaketime due to fallback during training.

SW-A1 No. 3 Footer print

When set to "1", the date of reception, the sender machine No., and thepage No. are automatically recorded at the end of reception.

SW-A1 No. 4 Length limitation of copy/send/receive

Used to set the maximum page length.

To avoid possible paper jam, the page length is normally limited to 0.6meter for copy or transmit, and 1.5 meters for receive.

It is possible to set it to "No limit" to transmit a long document, such as acomputer print form, etc. (In this case, the receiver must also be set tono limit.)

SW-A1 No. 5 CSI transmission

(CSI TRANSMISSION) is a switch to set whether the machine sends ordoes not send the signal (CSI signal) informing its own telephone No. tothe remote fax. machine when information is received. When"nonsending" is set, the telephone No. is not output on the remote trans-mitting machine if the remote transmitting machine has the function todisplay or print the telephone No. of receiving machine, using this CSIsignal.

SW-A1 No. 6 DIS receive acknowledgment during G3 transmission

Used to make a choice of whether reception of DIS (NSF) is acknowl-edged after receiving two DISs (NSFs) or receiving one DIS (two NSFs).It may be useful for overseas communication to avoid an echo sup-pression problem, if set to 1.

SW-A1 No. 7 Non-modulated carrier for V29 transmission modem

Though transmission of a non-modulated carrier is not required for trans-mission by the V29 modem according to the CCITT recommendation, itmay be permitted to a send non-modulated carrier before the imagesignal to avoid and echo suppression problem. It may be useful for over-seas communication to avoid an echo suppression problem, if set to 1.

SW-A1 No. 8 EOL (End Of Line) detect timer

Used to make a choice of whether to use the 25-second or 13-secondtimer for detection of EOL.This is effective to override communication failures with some facsimilemodels that have longer EOL detection.

SW-A2 No. 1 ~ No. 4 Modem speed

Used to set determine the initial modem speed. The default is 9600BPS.It may be necessary to program it to a slower speed when frequent linefallback is encountered, in order to save the time required for fallbackprocedure.

SW-A2 No. 5 Sender’s information transmit

(SENDER’S INFORMATION TRANSMISSION) is a switch to set thefunction to print the content of HEADER PRINT described in the passcodelist at the front end of receiver’s original when original is sent to theremote machine.

If this switch is set to "NO", the HEADER PRINT is not output at thereceiving machine.

SW-A2 No. 6 H2 mode

Used to determine reception of H2 mode (15 sec transmission mode).When set to OFF, H2 mode reception is inhibited even though the trans-mitting machine has H2 mode function.

SW-A2 No. 7 Communication error treatment in RTN sending mode(Reception)

Used to determine communication error treatment when RTN is sent byoccurrence of a received image error in G3 reception. When it is set to"1", communication error is judged as no error.

SW-A2 No. 8 CNG transmission

When set to "0" , this model allows CNG transmission by pressing theStart key in the key pad dialing mode. When set to "1", CNG transmis-sion in the key pad dialing mode cannot be performed. In either case,CNG transmission can be performed in the auto dial mode.

SW-A3 No. 1, No. 2 CED tone signal interval

For international communication, the 2100Hz CED tone may act as anecho suppression switch, causing a communication problem.

Though SW-A3 No. 1 and No. 2 are normally set to 0, it should be changedthis time between the CED tone signal to eliminate the communicationproblem caused by echo.

SW-A3 No. 3 MR Coding

Used to select the MR coding enable or disable.

SW-A3 No. 4 ~ No. 8 Reserved

Set to "0".

SW-A4 No. 1 ~ No. 5 Signal transmission level

Used to control the signal transmission level in the range of-0dB to-31dB.

The factory setting is at -10dB (MODEM output).

SW-A4 No. 6 Protocol monitor (Error print)

If set to "1", protocol is printed at communication error.

SW-A4 No. 7 Protocol monitor

Normally set to "0". If set to "1", communication can be checked, in caseof troubles, without using a G3 tester or other tools.When communication FSK data transmission or reception is made, thedata is taken into the buffer. When communication is finished, the data isanalyzed and printed out. When data is received with the line monitor(SW-A4 No. 8) set to "1" the reception level is also printed out.

SW-A4 No. 8 Line monitor

Normally set to "0". If set to "1", the transmission speed and the recep-tion level are displayed on the LCD. Used for line tests.

SW-A5 No. 1, No. 2 Digital line equalization setting (Reception)

Line equalization when reception is to be set according to the line char-acteristics.

Setting should be made according to distance between the telephoneand the telephone company central switching station.

SW-A5 No. 3, No. 4 Reserved

Set to "0".

SW-A5 No. 5, No. 6 Digital cable equalizer setting(Reception for Caller ID)

Line equalization when reception for CALLER ID is to be set accordingto the line characteristics.

Setting should be made according to distance between the telephoneand the telephone company central switching station.

SW-A5 No. 7 Error criterion

Used to select error criterion for sending back RTN when receiving im-age data.

2 – 12

TX RX

CED

DIS

T

UX-108U/178U/188UFO-375U

SW-A5 No. 8 Anti junk fax check

When use the Anti junk fax function, set to "1".

SW-A6 No. 1 Auto gain control (MODEM)

When this mode is enabled, if the reception signal level is under 31dBm.The modem itself controls the signal gain automatically.

SW-A6 No. 2 End buzzer

Setting this bit to 0 will disable the end buzzer (including the error buzzer/on-hook buzzer).

SW-A6 No. 3 Disconnect the line when DIS is received in RX mode

Bit1= 0: When DIS signal is received during RX mode, disconnected theline is immediately.

Bit1= 1: When DIS signal is received during RX mode, wait the nextsignal.

SW-A6 No. 4 Equalizer freeze control (MODEM)

This switch is used to perform reception operation by fixing the equal-izer control of modem for the line which is always in unfavorable stateand picture cannot be received.* Usually, the control is executed according to the state of line where

the equalizer setting is changed always.

SW-A6 No. 5 Equalizer freeze control 7200BPS only

Setting which specifies SW-A3 No. 6 control only in the condition of7200BPS modem speed.

SW-A6 No. 6 CNG transmission in manual TX mode

When set to "1", fax transmit the CNG signal in case of manual trans-mission mode (User press the START key after waiting the fax answer-ing signal from handset or speaker).

SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode

When set to "0", if the other fax is Sharp model, fax transmit the docu-ment by H2 mode. When set to "1", even if the other fax is Sharp model,fax transmit the document by MR mode.

SW-A6 No. 8 Reserved

Set to "0".

SW-B1 No. 1 ~ No. 4 Recall interval

Choice is made for a redial interval for speed and rapid dial calls.Used a binary number to program this. If set to 0 accidentally, 1 will beassumed.

SW-B1 No. 5 ~ No. 8 Recall times

Choice is made as to how many redials should be.

SW-B2 No. 1 Dialing pause (sec/pause)

Pauses can be inserted between telephone numbers of direct dial con-nection. Selection of 4 sec or 2 sec pause is available.

SW-B2 No. 2, No. 3 Reserved

Set to "0".

SW-B2 No. 4 Busy tone detection (after auto dial)

Used to set YES/NO of busy tone detection after auto dialing.

SW-B2 No. 5 Waiting time after dialing

This is waiting time for the opponent’s signals after dialing.

When set to "0", waiting time is 45 sec.

When set to "1", waiting time is 90 sec.

SW-B2 No. 6 ~ No. 8 Reserved

Set to "0".


Set to "0".

SW-B3 No. 8 Hold function

Used to set YES/NO of holding function by the HOLD key.

SW-B4 No. 1 Auto dial mode Delay timer of before line connect

Delay time between the dial key input and line connection under theauto dial mode.

SW-B4 No. 2 Auto dial mode Delay timer of after line connect

Delay time between the line connection and dial data output under theauto dial mode.

SW-B4 No. 3 Dial mode

When using the pulse dial, set to 0. When using the tone dial, set to 1.

SW-B4 No. 4 Pulse → Tone change function by key

When setting to 1, the mode is changed by pressing the key from thepulse dial mode to the tone dial mode.

SW-B4 No. 5 Dial pulse make/break ratio (%)

When using the 33 % make ratio pulse dial, set to "0".When using the 40 % make ratio pulse dial, set to "1".


Set to "0".

SW-B5 No. 1 ~ No. 5 DTMF signal transmission level (Low)

The transmission level of DTMF signal is adjusted. (lower frequency)

00000: 0dBm

↓

11111: -15.5dBm (-0.5dBm x 31)


Set to "0".

SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High)

The transmission level of DTMF signal is adjusted. (higher frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)


Set to "0".

SW-C1 No. 1, No. 2 Reading slice (Binary)

Used to determine the set value of reading density in standard/fine mode.The standard setting is "00" (Factory setting is "00")

SW-C1 No. 3, No. 4 Reading slice (Half tone)

Used to determine the set value of reading density in half tone mode.The standard setting is "00" (Factory setting is "00")

SW-C1 No. 5 Line density selection

Used to set the transmission mode which is automatically selected whenthe Resolution key is not pressed. In the copy mode, however, the finemode is automatically selected unless the Resolution key is manuallyset to another mode.

SW-C1 No. 6 Half tone gray scale selection

Used to determine the reading gray scale in half tone mode.

When set to "0", gray scale is 64 levels.

When set to "1", gray scale is 16 levels.

2 – 13

RAPID01 CML RELAY ON

DIALLING

0 : 0sec 1 : 3sec

RAPID01 CML RELAY ON

0 : 1.7 sec 1 : 3 sec

DIAL DATA

UX-108U/178U/188UFO-375U

SW-C1 No. 7 MTF correction in half tone mode

This allows selection of MTF correction (dimness correction) in the halftone mode.When "NO" (=1) is selected, the whole image becomes soft and mild.On the contrary, however, clearness of characters will be reduced. Nor-mally set to "YES" (=0).

SW-C1 No. 8 Reserved

Set to "0".

SW-D1 No. 1 ~ No. 4 Number of rings for auto receive

When the machine is set in the auto receive mode, the number of ringsbefore answering can be selected. It may be set from one to four ringsusing a binary number. Since the facsimile telephone could be used asan ordinary telephone if the handset is taken off the hook, it should beprogrammed to the user’s choice. If the soft switch was set to 1, directconnection is made to the facsimile. If a facsimile calling beep was heardwhen the handset is taken off the hook, press the START key and putthe handset on the hook to have the facsimile start receiving. If it wasset to 0 accidentally, receive ring is set to 1.NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have diffi-culty receiving faxes, reduce the number of rings to a maximumof 5.

SW-D1 No. 5 Automatic switching manual to auto receive mode

This soft switch is used to select whether the machine should switch tothe auto receive mode after 5 rings in the manual receive mode or re-main in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5rings).

SW-D1 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D2 No. 1 ~ No. 3 Distinctive ringing settingFactory setting: OFF

When the ringing setting is turned off, all of the CI signal are received.When any of the standard, and ring patterns 1 through 3 is selected forthe ringing setting, only the selected CI signal is received.

CI signal patternsThe CI signal patterns consists of the standard pattern, and ring pat-terns 1 through 7. The standard pattern is the conventional one.

SW-D2 No. 4 Reserved

Set to "0".

SW-D2 No. 5 Caller ID function

Used for Caller ID function.

SW-D2 No. 6, No. 7 CI off detection timer (Distinctive ring settingoff only)

Set the minimum time period of CI signal interruption which affords tobe judged as a CI OFF section.

SW-D2 No. 8 Reserved

Set to "0".

SW-E1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-E2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detect time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used inremote reception (5 ).

The longer the detect time is, the less the error detection is caused bynoises.

SW-F1 No. 3 Protection of remote reception (5 ) detect

Used to set the function of remote reception (5 ). When set to "1",the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

(Corresponding to TEL made by GE) P. B. X.

"1": Compatible with TEL mode by GE

"0": Not compatible

• When sending (5 ) for remote reception with a GE manufac-tured telephone remote reception may not take place because ofspecial specifications in their DTMF.To overcome this, a soft SW is provided to change the modem set-ting to allow for remote reception.

• If this soft SW is set to "1", other telephone sets may be adverselyaffected.

SW-F1 No. 5 ~ No. 8 Remote operation code figures by externalTEL (0 ~ 9)

Remote operation codes can be changes from 0 through 9. If set togreater than 9, it defaults to 9. The "5 " is not changed.Ex-7 (Default: 5 )

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standbystops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 Fax signal detection after telephone mode dial

When set to "1", if machine detect the fax answering signal after tel-ephone calling (handset off-hook or speaker mode dial), machine startto receive the documents automatically.

SW-F2 No. 7, No. 8 Reserved

Set to "0".

2 – 14

1S

3.5S

1S

0.5S

RING PATTERN 1 for CANADA

2S

4S

1.5S

3S

1S

4S

1.5S

4S

0.8S

4S

0.3S

4S

0.4S

4S

1S

3S

0.5S

3S

0.5S

3S

2S

2S

0.5S

0.5S

1S

0.2S

0.8S

0.4S

0.3S

0.2S

0.4S 0.8S

0.2S 0.2S

1S

1S

1S 0.5S

0.5S0.5S

0.5S 1S

0.5S0.5S

STANDARD

RING PATTERN 1

for USA

RING PATTERN 2

for USA

RING PATTERN 3

for USA



A B

400msec 2000msec1 2

UX-108U/178U/188UFO-375U

SW-G1 No. 1 ~ No. 4 Quiet detect time

When an answering machine is connected, if a no sound state is de-tected for a certain period of time, the machine judges it as a transmis-sion from a facsimile machine and automatically switches to the FAXmode.

SW-G1 No. 5 ~ No. 8 Quiet detect start timing

Inserts a pause before commencing quiet detection.

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-G3 No. 1 ~ No. 4 Reserved

Set to "0".

SW-G3 No. 5, No. 6 Section time of quiet detection

The switch which sets the time from the start of detection function to theend of the function.

SW-G3 No. 7, No. 8 Reserved

Set to "0".

SW-H1 No. 1 Busy tone detection ON/OFF time (Lower duration)

The initial value of detection is set according to electric condition.

The set value is changed according to the local switch board. (Erro-neous detection of sound is reduced.)

Normally the upper limit is set to 900msec, and the lower limit to 200msec.

If erroneous detection is caused by sound, etc., adjust the detectionrange.

The lower limit can be set in the range of 350msec to 200msec.

SW-H1 No. 2 Busy tone detection ON/OFF time (Upper duration)

Similarly to SW-H1 No. 1, the set value can be varied.

The upper limit can be set in the range of 650msec to 900msec.

SW-H2 No. 4 ~ No. 8 Reserved

Set to "0".

SW-I1 No. 1 ~ No. 8 Reserved

Set to "0".


Set to "0".


Set to "0".


Set to "0".


Set to "0".


Set to "0".


Set to "0".

SW-J1 No. 1, No. 2 Reserved

Set to "0".

SW-J1 No. 3 Sender’s phone number setting

Used to make a choice of whether the registered sender’s phone numbercan be changed or not. If the switch is set to "1", new registration of thesender’s phone number is disabled to prevent accidental wrong input.


Set to "0".

SW-J1 No. 6 Day light saving setting

This is used to set YES/NO of automatic clock adjustment for day lightsaving.

SW-J1 No. 7, No. 8 Ringer volume

Used to adjust ringing volume.

SW-J2 No. 1, No. 2 Speaker volume

Used to adjust sound volume from a speaker.

SW-J2 No. 3 Polling key

If this switch is set to 1, the last of Rapid key works as polling key.

SW-J2 No. 4, No. 5 Handset receiver volume

Used to adjust sound volume from a handset receiver volume.

SW-J2 No. 6 ~ No. 8 Reserved

Set to "0".


Set to "0".

SW-J3 No. 3, No. 4 Communication result printout (Transaction re-port)

It is possible to obtain transaction results after each communication.Normally, the switch is set (No. 1: 0, No. 2: 0) so that the transactionreport is produced only when a communication error is encountered. IfNo. 1 was set to 1 and No. 2 to 0, the transaction report will be producedevery time a communication is done, even if the communication wassuccessful.Setting No. 1 to 1 and No. 2 to 1 will disable this function. No transactionreport printed.

SW-H1 No. 1 SW-H1 No. 2 Detection range

0 0 200msec ~ 900msec

0 1 200msec ~ 650msec

1 0 350msec ~ 900msec

1 1 350msec ~ 650msec

SW-H1 No. 3 Reserved

Set to "0".

SW-H1 No. 4 Busy tone continuous sound detect time

Set detecting time busy tone continuous sound for 5 seconds or 10 sec-onds.


Set to "0".

SW-H1 No. 6 Busy tone detect continuation sound detect

Used to select detection of the continuous sound of certain frequency.


Set to "0".

SW-H1 No. 8 Busy tone detect intermittent sound detect

Used to select detection of the intermittent sound of certain frequency.

SW-H2 No. 1, No. 2 Busy tone detection pulse number

Used to set detection of Busy tone intermittent sounds.

SW-H2 No. 3 Fax switching when A.M. full

If the answering machine’s memory (tape) is full and there is no re-sponse, the machine automatically switches to Fax reception.

2 – 15

UX-108U/178U/188UFO-375U

SW-J3 No. 5 ~ No. 8 Reserved

Set to "0".

SW-K1 No. 1 Entering DIAG mode by pressing SPEED key

A bit which is used in the production process only. When the SPEED keyis pressed, the switch is changed from the stand-by state to the DIAGmode.

SW-K1 No. 2 ~ No. 8 Reserved

Set to "0".

SW-L1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-L2 No. 1 ~ No. 8 Reserved

Set to "0".

2 – 16

UX-108U/178U/188UFO-375U

[3] Troubleshooting

Refer to the following actions to troubleshoot any of problems mentionedin 1-4.

[1] A communication error occurs.

[2] Image distortion produced.

[3] Unable to do overseas communication.

[4] Communication speed slow due to FALLBACK.

• Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.May be used in case [1] [2] [3].

• Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,5. May be used in case [3].

• Apply line equalization SOFT SWITCH A5-1, 2.May be used in case [1] [2] [3] [4].

• Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,4. May be used in case [2] [3].

• Replace the TEL/LIU PWB.May be used in all cases.

• Replace the control PWB.May be used in all cases.

* If transmission problems still exist on the machine, use the followingformat and check the related matters.

TO: ATT: Ref.No. :

CC: ATT: Date :

FM: Dept :

Sign :

2 – 17

* Please complete this report before calling the “TAC” hotline if problem still occurs.

***** Facsimile communication problem ***** Ref.No.:

Date:From: Mr. Fax Tel No.:Our customer Name Tel No.

Address Fax No.

Contact person Model name

Other party Name Tel No.Address Fax No.Contact person Model name

Problem mode Line: Domestic / international Model: G3 Phase: A, B, C, D.

Reception / TransmissionAutomatic reception / Manual receptionAutomatic dialing / Manual dialing / Others

Frequency: % ROM version:

Confirmationitem

Please mark problem with an X.No problem is: 0.

A1 A2 B1 B2 C1 C2 D1 D2 E1 E2

Transmission level setting is ( ) dB at ourcustomer

Transmission level ( ) dBmReception level ( ) dBmBy level meter at B1 and B2

Comment

**** Please attach the G3 data and activity report on problem. ****

Countermeasure

Our customer

Our service

A1 A2 C1 D2

B1B2

E1E2

C2 D1

Other party

Other party's service

UX-108U/178U/188UFO-375U

[4] Error code table

1. Communication error code table

G3 TransmissionCode Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSF, DIS Cannot recognize DCS signal by echo etc.

Cannot recognize NSS signal (FIF code etc)

2 CFR Disconnects line during reception (carrier missing etc)

3 FTT Disconnects line by fall back

4 MCF Disconnects line during reception of multi page

Cannot recognize NSS, DCS signal in the case of mode change

5 PIP or PIN The line is hung up without replying to telephone request from the receiving party.

6 RTN or RTP Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.

7 No signal or DCN No response in receiver side or DCN signal received* (transmitter side)

8 − Owing to error in some page the error could not be corrected although the specified number of

error retransmission was at tempted.

11 − Error occurred after or while reception by the remote (receiving) machine was revealed to be

impossible.

12 − Error occurred just after fallback.

13 − Error occurred after a response to retransmission end command was received.

G3 Reception

Code Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSS, DCS Cannot recognize CFR or FTT signal

Disconnects line during transmission (line error)

2 NSC, DTC Cannot recognize NSS signal (FIF code etc)

3 EOP Cannot recognize MCF, PIP, PIN, RTN, RTP signal

4 EOM Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change

5 MPS The line is hung up without replying to communication request.

6 PR1-Q Cannot recognize PIP, PIN signal in the case of TALK request

7 No signal or DCN No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)

8 − Error occurred upon completion of reception of all pages.

9 − Error occurred when mode was changed or Transmission/Reception switching was performed.

10 − Error occurred during partial page or physical page reception.

11 − Error occurred after or during inquiry from the remote (transmitting) machine as to whether

reception is possible or not.

12 − Error occurred during or just after fallback.

13 − Error occurred after the retransmission end command was received.

2 – 18

UX-108U/178U/188UFO-375U

CHAPTER 3. MECHANISM BLOCKS

[1] General description

1. Document feed block and diagram

Fig. 1

2. Document feed operation1) The document placed in the hopper actuates the document sensor.

After one second, the pulse motor starts to drive the paper feed roller.The document is automatically taken up into the machine, and stoppedat the document sensor.

2) When a specified number of pulses are received from the documentsensor after the document lead edge is sensed, scanning is started.

3) When a specified number of pulses are received from the documentsensor after the document rear edge is sensed, scanning is termi-nated and the document is fed through.

4) If the document sensor is active (i.e., another document is in thehopper), when the preceding document scanning is completed and itis fed out, the next document is taken up into the machine. If thedocument sensor is not active (i.e., there is no document in the hop-per), when the document is fed out, the operation is terminated.

3. Hopper mechanism

3-1. General view

Fig. 2

The hopper is used to align documents with the document guides ad-justed to the paper width.NOTE: Adjust the document guide after setting up the document.

3-2. Automatic document feed1) Use of the paper feed roller and separation rubber plate ensures er-

ror-free transport and separation of documents. The plate springpresses the document to the paper feed roller to assure smooth feed-ing of the document.

2) Document separation method: Separation rubber plate

Fig. 3

3-3. Documents applicable for automatic feed

NOTE: Double-side coated documents and documents on facsimile re-cording paper should be inserted manually. The document feedquantity may be changed according to the document thickness.

Documents corresponding to a paper weight heavier than 64.3kg (74.3g/m2 ) and lighter than 135kg (157g/m2 ) are acceptable for manual feed.

Documents heavier than 135kg in terms of the paper weight must beduplicated on a copier to make it operative in the facsimile.

3-4. Loading the documents

1) Make sure that the documents are of suitable size and thickness, andfree from creases, folds, curls, wet glue, wet ink, clips, staples andpins.

2) Place documents face down in the hopper.

i) Adjust the document guides to the document size.

ii) Align the top edge of documents and gently place them into thehopper. The first page under the stack will be taken up by the feedroller to get ready for transmission.

NOTES: 1) Curled edge of documents, if any, must be straightenout.

2) Do not load the documents of different sizes and/orthicknesses together.

3 – 1

Paper size B6 (128mm x 182mm) ~A4 (210mm x 297mm), Letter (216mm x 279mm)

4x6 series(788mm x 1091mm x1000mm sheets)

Squaremeter series

Minimum Maximum Minimum Maximum

Feeder capacity 10 sheets, max.

Paper thickness (ref.) 0.06mm 0.09mm 0.06mm 0.09mm

Paper weight 45kg 64.3kg 52g/m2 74.3g/m2

Fig. 4

Separator rubber

Rear roller A/B

Transfer roller

Pinch roller

CIS

Paper feed roller

Document

Paper feed spring

Separator rubber Paper feed spring

Document

Paper feed roller

Separator rubber Paper feed spring

Paper feed roller

Last page of document

First page of document

Back of document

UX-108U/178U/188UFO-375U

3-5. Documents requiring use of document carrier

1) Documents smaller than B6 (128mm x 182mm).

2) Documents thinner than the thickness of 0.06mm.

3) Documents containing creases, folds, or curls, especially those whosesurface is curled (maximum allowable curl is 5mm).

4) Documents containing tears.

5) Carbon-backed documents. (Insert a white sheet of paper betweenthe carbon back and the document carrier to avoid transfer of carbonto the carrier.)

6) Documents containing an easily separable writing material (e.g., thosewritten with a lead pencil).

7) Transparent documents.

8) Folded or glued documents.

Document in document carrier should be inserted manually into thefeeder.

4. Document release

4-1. GeneralWhen the release lever is pulled by hand in the direction of arrow, thelatch is released and the upper document guide moves on its axis in thederection of the arrow. The feed rollers, the separation rubber plate, andthe pinch rollers become free to make it possible to remove the docu-ment.

4-2. Cross section view

Fig. 5

5. Recording block

5-1. General view

3 – 2

Operation panel unit

Scanner frame unit

PWB case unit

Lower cabinet

Fig. 6

5-2. DrivingVia the pulse motor gear shaft, the reduction gear, and the recordingpaper feed gear, rotation of the pulse motor is conveyed to the recordingpaper feed roller to feed the recording paper.

5-3. RecordingUse of a thermal head permits easier maintenance and low operatingcosts.

1) Thermal headThe thermal head consists of 1728-dot heat elements arranged in a sin-gle row and has the resolution of 8 dots/mm. The maximum recordingspeed is 10ms/line. The thermal head also incorporates a 1728-dot shiftregister latch and output control driver circuit. Low power consumptionis achieved by dividing the head into nine segments.

2) Structure of the recording mechanismRecording is accomplished by pressing the thermal head on the record-ing paper against the platen roller.

The main scan (horizontal) is electronically achieved, while the subscan(vertical) is achieved by moving the recording paper by the recordingplaten roller.

Usually, the cause for uneven print tone is caused by misalignment ofthe thermal head or uneven contact with the roller.

It can be checked in the following manner.

1) Check if the thermal head power and signal cables are properly routed.

2) Check that the thermal head pivot moves smoothly up and down.

3) Check that the thermal head support bracket is secured without anyplay.

4) Check to see that the recording platen roller has proper concentricity,in the case of a print tone variation evenly repeated down the page.

5) Replace the thermal head with a new one and check to see if thesame trouble occurs.

RECORDING BLOCK (CUTTER MODEL)

Scanner frame

Thermal head

Cutter coverPlaten roller

Paper support

Recording paper

Cutter guideCutter unit

RECORDING BLOCK (NON CUTTER MODEL)

Scanner frame

Thermal head

Paper guide upper

Platen roller

Paper support

Recording paper

UX-108U/178U/188UFO-375U

[2] Disassembly and assembly procedures

• This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures.

• Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units,refer to the Parts List.

• The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.

• To assure reliability of the product, the disassembly and the assembly procedures should be performed carefully and deliberately.

Handset cover and paper support guide1 Parts list (Fig. 1)

No. Part name Q’ty No. Part name Q’ty

1 Mechanism unit 1

2 Handset cover 1

3 Hook switch lever 1

4 Screw (ø3×12) 2

5 Paper support guide unit 1

6 Anti curl shaft 1

Fig. 1

3 – 3

7 Anti curl spring 2

8 PO pinch roller 2

9 Paper sensor lever 1

10 Paper sensor lever spring 1

11 Guide sheet 2

12 Paper support guide 1

9

106

3

2

2

3

4

5

6

7

4

4 1

5

5

1

8

78

7

12

1

8

9

10

11

12

Hook

Hook

Lock the all hook(4place)

11

11

UX-108U/178U/188UFO-375U

PWB case top, bottom and PWB2 Parts list (Fig. 2)

Fig. 2

3 – 4


1 Mechanism unit 1

2 Screw (3×6) 1

3 Head earth cable 1

4 Connector 2

5 Screw (3×10) 1

6 PWB case unit 1

7 Screw (3×10) 2

8 PWB case, top 1

9 Screw (4×6) 1

10 AC cord ass’y 1

11 Screw (3×6) 1

12 TEL ARG cable 1

13 Power supply PWB unit 1

14 TEL/LIU PWB unit 1

15 Rubber leg 2

16 PWB case, bottom 1

2

3

4

5

6

1

6

13

10

1112

15

77

16

1

8

7

9

10

11

12

13

14

15

169

8

AC cordearth cable

45˚

2

5

3

4

4

Rib

3

ControlPWB

14

UX-108U/178U/188UFO-375U

Operation panel unit and scanner frame3 Parts list (Fig. 3)

Fig. 3

3 – 5


1 Mechanism unit 1

2 Screw (3×10) 2

3 Scanner frame unit 1

4 Document guide lower 1

5 Reduction gear, 17/36Z 1


7 Idler gear, 25Z 1

8 Feed roller shaft 1

9 Feed roller 1

10 CIS cable 1

11 CIS support, right 1

12 CIS unit 1

13 CIS support, left 1

14 CIS spring 2

15 Scanner frame 1

16 Panel and head cable 2

17 Operation panel unit 1

2

3

4

516

17

1

7

6

8

9

10

11

14

15

12

13

8

4

15

98

5

6

147

10

14

11

2

232

3

116

16

17

1

1312

Stopper plate

Hook

Hook

Hook

2

3

1

UX-108U/178U/188UFO-375U

Document guide upper unit and headframe

4Parts list (Fig. 4)

Fig. 4

3 – 6



2 Screw (3×10) 2

3 Support plate 1

4 Document guide upper 1

unit

5 Screw (3×10) 2

6 Head sheet 1

7 Head cable 1

8 Head spring A 2

9 Head spring B 3

10 Screw (3×6) 1

11 Head support, right 1

12 Screw (3×6) 1

13 Head earth cable 1

14 Head support, left 1

15 Thermal head 1

16 Pinch roller shaft 1

17 Pinch roller 2

18 Pinch roller pressing 2

spring

19 Head frame 1

1

4

2

162

1718

18

12

13

14

6

5

98

1011

15

53

19

87

13 14

B

A

View:A View:B

2

3

4

5

6

1

8

7

9

10

11

12

13

14

15

16

17

18

19

UX-108U/178U/188UFO-375U

Document guide upper5 Parts list (Fig. 5)

Fig. 5

3 – 7


1 Rear sheet 1

2 CIS gear, 29Z 1

3 CIS roller A ass’y 1

4 Transfer bearing 1

5 CIS roller B ass’y 1

6 Transfer roller 1

7 Transfer bearing 1

8 Idler gear, 20Z 1

9 Panel lock lever spring 1

10 Panel lock lever 1

11 Document sensor lever 1

spring

12 Document sensor lever 1

13 Separate spring 1

14 Separator plate 1

15 Paper feed spring 1

16 Separator rubber 1

17 Document guide upper 1

2

1

3

4

5

6

8

7

9

10

11

12

13

14

15

16

17

Applying standard

Applying standard

12

11

14

13

13

16

15

12

11

9

8

17

16

72

4

3

5

1

10

UX-108U/178U/188UFO-375U

Operation panel6 Parts list (Fig. 6)

Fig. 6

3 – 8



2 Screw (2×6) 3

3 Operation panel cable 1

4 Operation panel PWB 1

5 Document tray 1

6 Screw 1

7 Pinion gear 1

8 Hopper spring 1

9 Hopper guide, right 1

10 Hopper guide, left 1

11 Stop key 1

12 Start key 1

13 Direct key 1

14 12 key 1

15 Operation panel 1

Operation panel PWB LCD cable

LCD PWB

Confim of HOPPER GUIDE position

HOPPER GUIDE (R)

HOPPER GUIDE (L)

2

3

4

5

6

1

8

7

9

10 11

12

13

14

15 15

1

10

9

8

67

5

11

1213

14

22

3

2

4

1

RibRibGAP 0

GAP 0

UX-108U/178U/188UFO-375U

Parts list (Fig. 7)

Fig. 7

Drive unit, PWB and cutter7

3 – 9


1 Mechanism unit 1

2 Screw (3×10) 2

(Cutter model)

2 Screw (3×10) 1

(Non Cutter model)

3 Cutter arm 1

(Cutter model only)

4 Drive unit 1

5 Platen gear 1

6 Platen roller 1

7 Platen bearing 2

8 Screw (3×10) 1

(Cutter model only)

9 Cutter unit 1

(Cutter model only)

10 Screw (3×10) 1

(Cutter model only)

11 Cutter cover 1

(Cutter model only)

12 Cutter guide 1

(Cutter model only)

13 Cutter 1

(Cutter model only)

14 Screw (3×10) 2

15 Speaker cable 1

16 Control PWB unit 12

3

4

5

16

1

7

6

8

9

10

11

14

15

12

13

1

5

7

6

1

2 2

4

2 4

215

14

1416

6

16

7

35

78

9

10

1112

13

1

4

1

4

OK NGCuttermodelonly

UX-108U/178U/188UFO-375U

1 Mechanism unit 1

2 Paper sensor lever spring 1

(Cutter model only)

3 Paper sensor lever (Cutter model only) 1

4 Screw 2

5 Speaker 1

6 Paper guide upper (Non cutter model only) 1

Parts list (Fig. 8)

No. Part name Q’ty

Fig. 8

Speaker, paper sensor lever and paperguide upper8

3 – 10

2

3

4

5

1

1

2

3 4 4

5

6

1

1

5

1

6

2

3

RibHook

Hook

6

UX-108U/178U/188UFO-375U

Drive frame (Non cutter model)9

Fig. 9

3 – 11

Parts list (Fig. 9)


1 Change lever spring 1

2 Planet gear, 17Z 1

3 Change lever A 1

4 Cam 1



7 Planet gear spring 1

8 Planet gear lever A 1



11 Planet gear lever B 1

12 Idler gear, 25Z 1

13 Cam switch 1

14 Reduction gear, 17Z 1


16 Screw (3×10) 1

17 Motor 1

18 Motor heat sink 1

19 Drive frame 1

1

2

3

4

5

6

9

19

7

10

8

11

13

12

14

15

16

17

18

1619 13

17 18

1913

146

7

8

11

9

1015

412

2

1

1

3

3

5

107

To be the switchlinked by hooks

Grease

Grease

Green

Lock the MOTORby this rib

SECTION : A-A

A

A

Hook be doing lock

NOTE) Apply certainly to a part of a nail at the time of GREASE application

GEAR attachment boss

,

96 ,

UX-108U/178U/188UFO-375U

Drive frame (Cutter model)10

Fig. 10

3 – 12

Parts list (Fig. 10)

No. Part name Q’ty No. Part name Q’ty No. Part name Q’ty

1 Cutter cam switch 1



4 Planet gear lever C 1

5 Change lever spring 1


7 Change lever A 1

8 Cam 1


10 Cutter gear, 44Z 1



13 Planet gear lever A 1



16 Planet gear lever B 1


18 Cam switch 1







25 Screw (3×10) 1

26 Motor 1

27 Motor heat sink 1

28 Drive frame 1

1

2

5

8

9

10

11

14

3

6

12

15

4

7

13

16

18

17

19

20

21

22

23

24

25

26

27

28

25

28 1 18

26 27

1

2818

2111

12

13

16

14

15

24

23

817

6

5

5

7

742

3

20

19

922

12 15

10

3

To be the switchlinked by hooks

WHITE

GREEN

Lock the MOTORby this rib

SECTION : A-A

A

A

Hook be doing lock

, ,

,Grease

Grease

1411 ,

NOTE) Apply certanly to a part of a nail at the time of GREASE application

GEAR attachment boss

UX-108U/178U/188UFO-375U

Fig. 11

Wire treatment11 Parts list (Fig. 11)

3 – 13

1 Band 6

2 Screw (3×6) 2

3 Screw (4×6) 1

4 UL tape 1

5 Core (F2064) 1

6 Core (F2103) 1

No. Part name Q’ty

23

Rib

Power supplyPWB

TEL/LIUPWB

AC cord

ARGcable

OK NG

Head earth cable

Fixed this switch after adjusting the cutter gear in this drawing,(Cutter model only)

Cutter cable

Cutter cable(Cutter model only)

Camswitchcable

Camswitchcable

11

1

1

100 10mm

20 5mm

Head, head earth and panel cable

Head cable

Motor cable

Brinding the cable(Head cable/Head earth cable/CIS cable/panel cable/motor cable/cam cable)

Head cable and headearth cable

Head earth cable

Head cable

Operation panel PWB

Panel cable

Panel cable

CIScable

CIScable

CIS unit

Speaker cable

16

11

15

16

5

Postion of core

Panel cable pass tothe core 2times The panel cable mustwiring

to under core

All the cables must wiring to the motor heat sink

Head cable and head earth cablepass to the core 2times

Binding the core with lower cabinet

0~2mm

19mmPanel cable 4

CIS cable

2

Rib

Speaker

Speaker cable

Control PWB

UX-108U/178U/188UFO-375U

4 – 1

[1] B

lock

dia

gram

CHAPTER 4. DIAGRAMS

MO

DE

M

CLO

CK

SR

AM

25

6Kbi

tR

OM

1M

bit

CP

U

CP

U I/

F

TIM

ER

RT

C

PIO

WA

TC

HD

OG

T

IME

R

CLO

CK

32

kHz

INT

ER

RU

PT

C

ON

TR

OLL

ER

CIS

I/F

MO

TO

R I/

F

SE

NS

OR

I/F

SIO

TH

ER

MA

L H

EA

D I/

F

PA

NE

L I/F

PM

OP

ER

AT

ION

P

AN

EL

LCD

CO

NT

RO

L P

WB

UN

IT1C

HIP

FA

X E

NG

INE

(X

FC

-3)

HA

ND

SE

T

SP

EA

KE

R

+5V

+24

V

OP

ER

AT

ION

P

AN

EL

TE

L/LI

U

PW

B U

NIT

DR

IVE

R

TH

ER

MA

L H

EA

D

PM

CO

NT

AC

T

IMA

GE

SE

NS

OR

DO

CU

ME

NT

SE

NS

OR

PO

WE

R S

UP

PLY

P

WB

UN

IT

PA

PE

R S

EN

SO

R A

ND

CU

TT

ER

: U

X-1

78U

/188

U/F

O-3

75U

ON

LY

AM

P/S

IGN

AL

SE

LEC

T

B

LOC

K

SP

EA

KE

R

AM

P

AM

P

AM

P

SU

RG

E

PR

OT

EC

T/

FIL

TE

RC

ML

TR

AN

S

CI

VB

T

RE

GU

LAT

OR

RE

CT

IFIE

R

TR

AN

S

RE

CT

IFIE

R

DIO

DE

TR

AN

SS

UR

GE

A

BS

OR

BE

RF

ILT

ER

ST

AB

ILIZ

ER

LIN

E

EX

T.T

EL

PA

PE

R

SE

NS

OR

RE

SE

T IC

24M

Hz

12M

Hz

CU

TT

ER

AM

P

BZ

UX-108U/178U/188UFO-375U

[2] W

iring

dia

gram

4 – 2

FG

CA

M S

W

CU

TT

ER

S

EN

SO

R

22

6

TH

ER

MA

L H

EA

D

CO

NT

AC

T IM

AG

E S

EN

SO

R

LCD

UN

IT

CN

LCD

OP

ER

AT

ION

P

AN

EL

PW

B

14

CN

PN

16 7 15

CN

CS

WC

NM

T

CN

TH

CN

CIS

CN

PN

CN

SP

SP

EA

KE

R

CN

CU

T1

CN

LIU

A

CN

PW

12 10

CO

NT

RO

L P

WB

UN

IT

TE

L/LI

U

PW

B U

NIT

PO

WE

R S

UP

PLY

P

WB

UN

IT

CN

LIU

CN

2

EX

TE

RN

AL

LIN

E

TE

L LI

NE

MJ1

/2

MJT

EL

AC

CO

RD

UX

-178

U/1

88U

/FO

-375

U O

NLY

TX

/RX

MO

TO

R

2

HA

ND

SE

T

FG

UX-108U/178U/188UFO-375U

[3] P

oint

- to

-poi

nt d

iagr

am

4 – 3

TX

/RX

MO

TO

R

TP

AD

TP

BD

TP

AD

TP

BD

VM

TV

MT

1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 151 2 3 4 5 6

OP

ER

AT

ION

PA

NE

LP

WB

TP

AD

TP

BD

TP

AD

TP

BD

VM

TV

MT

TH

ER

MA

LH

EA

D

VT

HV

TH

ST

RB

1S

TR

B2

TH

IR

AN

KM

GM

GM

G+

5VS

TR

B3

ST

RB

4LA

TC

HP

CLK

DA

TA

VT

H

VT

HV

TH

ST

RB

1S

TR

B2

TH

IR

AN

KM

GM

GM

G+

5VS

TR

B3

ST

RB

4LA

TC

HP

CLK

DA

TA

VT

H

1 2 3 4 5 6 7

1 2 3 4 5 6 7

VO

DG

+5V øT

CIS

CLK

GLE

D+

24V

VO

DG

+5V øT

CIS

CLK

GLE

D+

24V

KE

N4A

KE

N3A

KE

N2A

KE

N1A

DG

DG

+5V

OR

GS

NS

FR

SN

SE

SE

N4

SE

N3

SE

N2

SE

N1

SE

N0

KE

N4A

KE

N3A

KE

N2A

KE

N1A

DG

DG

+5V

OR

GS

NS

FR

SN

SE

SE

N4

SE

N3

SE

N2

SE

N1

SE

N0

CN

PN

CN

PN

CN

CIS

1 2 3 4 5 6 7 8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12

TE

L/LI

UP

WB

TE

LOU

TT

ELI

NT

ELM

UT

EC

IH

SR

HS

RX

INT

XO

UT

CM

L+

24V

A+

5V DG

TE

LOU

TT

ELI

NT

ELM

UT

EC

IH

SR

HS

RX

INT

XO

UT

CM

L+

24V

A+

5V DG

CN

LIU

CN

LIU

A

CN

MT

CN

TH

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10

PO

WE

RS

UP

PLY

PW

B

DG

+5V

VT

HO

NM

GM

GM

G+

24V

VT

HV

TH

VT

H

DG

+5V

VT

HO

NM

GM

GM

G+

24V

VT

HV

TH

VT

H

CN

2C

NP

W

CN

CS

W

CN

CU

T1

CN

SP

CIS

1 2C

SW

DG

CA

MS

WIT

CH

1 2C

UT

1D

GC

UT

TE

RS

WIT

CH

1 2

1 2 1 2 1 2S

P+

SP

-

CS

WD

G

CU

T1

DG

SP

+S

P-

SP

EA

KE

R

(CU

TT

ER

MO

DE

L O

NLY

)

CO

NT

RO

LP

WB

UX-108U/178U/188UFO-375U

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description

1. General descriptionThe compact design of the control PWB is obtained by using ROCK-WELL fax engine in the main control section and high density printing ofsurface mounting parts. Each PWB is independent according to its func-tion as shown in Fig. 1.

2. PWB configuration

Fig. 1

1) Control PWBThe control PWB controls peripheral PWBs, mechanical parts, trans-mission, and performs overall control of the unit.This machine employs a 1-chip modem (R96DFXL-CID) which is in-stalled on the control PWB.

2) TEL/LIU PWBThis PWB controls connection of the telephone line to the unit.

3) Power supply PWBThis PWB provides voltages of +5V and +24V to the other PWBs.

4) Panel PWBThe panel PWB allows input of the operation keys.

5) LCD PWBThis PWB controls the LCD display.

3. Operational descriptionOperational descriptions are given below:

• Transmission operation

When a document is loaded in standby mode, the state of the docu-ment sensor is sensed via the 1 chip fax engine (XFC3). If the sensorsignal was on, the motor is started to bring the document into thestandby position. With depression of the START key in the off-hookstate, transmission takes place.Then, the procedure is sent out from the modem and the motor isrotated to move the document down to the scan line. In the scanprocessor, the signal scanned by the CIS is sent to the internal im-age processor and the AD converter to convert the analog signal intobinary data. This binary data is transferred from the scan processorto the image buffer within the RAM and encoded and stored in thetransmit buffer of the RAM. The data is then con-verted from parallelto serial form by the modem where the serial data is modulated andsent onto the line.

• Receive operation

There are two ways of starting reception, manual and automatic.Depression of the START key in the off-hook mode in the case ofmanual receive mode, or CI signal detection by the LIU in the auto-matic receive mode.

First, the XFC3 controls the procedure signals from the modem to beready to receive data. When the program goes into phase C, theserial data from the modem is converted to parallel form in the mo-dem interface of the 1 chip fax engine (XFC3) which is stored in thereceive buffer of the RAM. The data in the receive buffer is decodedsoftware-wise to reproduce it as binary image data in the image buffer.The data is DMA transferred to the recording processor within theXFC3 which is then converted from parallel to serial form to be sentto the thermal head. The data is printed line by line by the XFC3which is assigned to control the motor rotation and strobe signal.

• Copy operation

To make a copy on this facsimile, the COPY key is pressed when themachine is in stand-by with a document on the document table andthe telephone set is in the on-hook state.

First, depression of the COPY key advances the document to thescan line. Similar to the transmitting operation, the image signal fromthe CIS is converted to a binary signal in the DMA mode via the 1chip fax engine (XFC3) which is then sent to the image buffer of theRAM. Next, the data is transferred to the recording processor in theDMA mode to send the image data to the thermal head which isprinted line by line. The copying takes place as the operation is re-peated.

LCDPWB

PANELPWB

CONTROLPWB

TEL/LIUPWB

POWERSUPPLYPWB

TX/RXMOTOR

AC CORD

5 – 1

UX-108U/178U/188UFO-375U

[2] Circuit description of control PWB

1. General descriptionFig. 2 shows the functional blocks of the control PWB, which is com-posed of 4 blocks.

Fig. 2 Control PWB functional block diagram

2. Description of each block

(1) Main control blockThe main control block is composed of ROCKWELL 1 chip fax engine(XFC3), ROM (128KByte), RAM (32KByte) and Modem (R96DFXL-CID).Devices are connected to the bus to control the whole unit.

1) XFC3 (IC3) : pin-144 QFP (XFC3)

2) R96DFXL-CID (IC2) : pin-100 QFP (MODEM)The FAXENGINE Integrated Facsimile Controllers.

XFC3, contains an internal 8 bit microprocessor with an external 2 Mbyteaddress space and dedicated circuitry optimized for facsimile imageprocessing and facsimile machine control and monitoring.

3) 27C1000 (IC8): pin-32 DIP (ROM)EPROM of 1Mbit equipped with software for the main CPU.

3) W24257S-70LL (IC5): pin-28 SOP (RAM)Line memory for the main CPU system RAM area and coding/decodingprocess. Used as the transmission buffer.

Memory of recorded data such as daily report and auto dials. When thepower is turned off, this memory is backed up by the lithium battery.

Fig. 3

MC24 CPU CONTROL IF

MC24 MEGACELL(8BIT DATA,24BIT ADDRESS) WATCHDOG TIMER REAL TIME CLOCK

CRYSTAL OSCILLATOR BATTERY BACK-UP CIRCUIT INTERRUPT CONTROLLER

BUS INTERFACE

DRAM CONTROL INTERNAL & EXTERNAL BUS CONTROL

INTERNAL & EXTERNAL DECODE DMA CONTROLLER OPERATOR PANEL IF

32 KEYS 8 LEDS

LCD MODULE SYNC SERIF 1

THERMAL PRINTER IF

5 ms LINE TIME A4/B4 LINES

TPH ADC 4 STROBE TPH

LATCHLESS TPH EXTEMAL DMA I/F

T.4/T.6 CODEC

MH,MR,MMR HARDWARE,ALTERNATE

COMPRESSION & DECOMPRESSION

BI-LEVEL RESOLUTION CONVERSION

PROGRAMMABLE

REDUCTION & EXPANSION

2.6kBYTE VIDEO RAM

SCANNER CONTROL & VIDEO PROCESSING 8-BIT PADC

CCD/CIS SCANNER 5 ms,A4/B4 LINES

SHADING CORRECTION(1:1,1:8) DITHERING

MULTILEVEL B4-A4 REDUCTION ERROR DIFFUSION

MTF

GENERAL I/O TONE/MODTONE

GPIO AUTOBAUD

SYNC-ASYNC SASIF SYNC SERIF 2

FLASH MEMORY IF AUTOBAUD

CPU BUS

INTERNAL CPU BUS

EXTERNAL CPU BUS

DMA BUS

WRPROTN

TSTCLKDEBUGNRESETNXINXOUTPWRDWNNBATRSTN

SYSCLK

SEE "OPIF OUTPUTS" BELOW

SEE "OPIF INPUTS" BELOW

THADIN

PDATPLATSTRB[3:0]STRBPOL

PCLK

PWR/GND TEST OPIF INPUTS OPI[0]/GPIO[21]/SSRXD1 OPI[1]/GPIO[22]/SSSTAT1 OPI[2]/GPIO[23]/SSCLK1 OPI[3]/GPIO[24]

OPIF OUTPUTS LEDCTL/GPO[16] LCDCS/GPO[17] OPO[0]/GPO[8] OPO[1]/GPO[9] OPO[2]/GPO[10] OPO[3]/GPO[11] OPO[4]/GPO[12]/SSTXD1 OPO[5]/GPO[13] OPO[6]/GPO[14] OPO[7]/GPO[15]

ROMCSN

MCSNSYNC

REGDMAWAITNRASN

CASN[1:0]DWRN

CSN[1:0]

WRNRDN

D[7:0]A[23:0]MIRQN

TONE

VINCLK1CLK1N

CLK2VIDCTL0/FCS1NVIDCTL1/FCS2N

START –VREF+VREF

GPIO[0] GPIO[1]/SASTXD GPIO[2]/SASRXD GPIO[3]/SASCLK GPIO[4] GPIO[5]/SSCLK2 GPIO[6]/SSTXD2 GPIO[7]/SSRXD2 GPIO[8]/FWRN GPIO[9]/FRDN GPIO[10]/SSSTAT2 GPIO[11]/BE/SERINP GPIO[12]/CS2N GPIO[13]/CS3N GPIO[14]/CS4N GPIO[15]/CS5N GPIO[16]/IRQ8 GPIO[17]/IRQ5N GPIO[18]/IRQ9N GPIO[19]/RDY/SEROUT GPIO[20]/ALTTONE SM[3:0]/GPO[7:4] PM[3:0]/GPO[3:0]

5 – 2

XFC3

ROM

MODEM

RAM

(1)

(2)

(4)

(3)

MAIN CONTROL BLOCK

MODEM BLOCK

UX-108U/178U/188UFO-375U

XFC3 (IC3) Terminal descriptions

CPU Control InterfaceMIRQn 135 I HU − Modem interrupt, active low. (Hysteresis In, Internal Pullup.)SYSCLK 133 I H − System clock. (Hysteresis In.)TSTCLK 130 O − 123XT Test clock.

Bus Control InterfaceA[23:0] [1:6][8:13] O TU 123XT Address bus (24-bit).

[15:20][22:27]D[7:0] [136:139] I/O TU 123XT Data bus (8-bit).

[141:144]RDn 128 O − 123XT Read strobe.WRn 127 O − 123XT Write strobe.ROMCSn 120 O − 123XT ROM chip select.CS1n 122 O − 123XT I/O chip select.CS0n 57 O − 123XT SRAM chip select. (Battery powered.)MCSn 121 O − 123XT Modem chip select.SYNC 126 O − 123XT Indicates CPU op code fetch cycle (active high).REGDMA 124 O − 123XT Indicates REGSEL cycle and DMA cycle.WAITn 125 O − 123XT Indicates current TSTCLK cycle is a wait state or a halt state.RASn 113 O − 123XT DRAM row address select. (Battery powered.)CAS[1:0]n [111:112] O − 123XT DRAM column address select. (Battery powered.)DWRn 109 O − 123XT DRAM write. (Battery powered.)

Prime Power Reset Logic and TestDEBUGn 129 I HU − External non-maskable input (NMI).RESETn 131 I/O HU 2XO XFC3 Reset.TEST 58 I C − Sets Test mode (Battery powered).

Battery Power Control and Reset LogicXIN 59 I OSC − Crystal oscillator input pin.XOUT 60 O − OSC Crystal oscillator output pin.PWRDWNn 62 I H − Used by external system to indicate loss of power to XFC3. (Results in NMI)BATRSTn 61 I H − Battery power reset input.WRPROTn 110 O − 1XC (Battery powered.) Write protect during loss of VDD power.

Scanner InterfaceSTART 101 O − 2XS Scanner shift gate control.CLK1 100 O − 2XS Scanner clock.CLK1n 99 O − 2XS Scanner clock-inverted.CLK2 98 O − 2XS Scanner reset gate control (or clock for CIS scanner).FCS1n/VIDCTL0 96 O − 2XT Flash memory chip select or Video Control signal.FCS2n/VIDCTL1 97 O − 2XT Flash memory chip select or Video Control signal.

Printer InterfacePCLK 29 O − 3XC Thermal Print Head (TPH) clock, or external DMAACK.PDAT 30 O − 2XP Serial printing data (to TPH).PLAT 31 O − 3XP TPH data latch.STRB[3:0] [33:36] O − 1XP Strobe signals for the TPH.STRBPOL 37 I C − Sets strobe polarity, active high/low.

Operator Panel InterfaceOPO[0]/GPO[8]/ 47 O − 2XL Keyboard/LED strobe [0] or GPO[8] or Scan Motor Power ControlSMPWRCTRLOPO[1]/GPO[9]/ 46 O − 2XL Keyboard/LED strobe [1] or GPO[9] or Print Motor Power ControlPMPWRCTRLOPO[2]/GPO[10]/ 44 O − 2XCT Keyboard/LED strobe [2] or GPO[10] or RINGERRINGEROPO[3]/GPO[11] 43 O − 2XL Keyboard/LED strobe [3] or GPO[11]OPO[4]/GPO[12]/ 42 O − 2XL Keyboard/LED strobe [4] or GPO[12] or SSTXD1 (for SSIF1)SSTXD1OPO[5]/GPO[13] 40 O − 2XL Keyboard/LED strobe [5] or GPO[13]OPO[6]/GPO[14] 39 O − 2XL Keyboard/LED strobe [6] or GPO[14]OPO[7]/GPO[15] 38 O − 2XL Keyboard/LED strobe [7] or GPO[15]OPI[0]/GPIO[21]/ 52 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [0] or GPIO[21] or SSRXD1SSRXD1 (for SSIF1)OPI[1]/GPIO[22]/ 51 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [1] or GPIO[22] or SSSTAT1SSSTAT1 (for SSIF1)OPI[2]/GPIO[23]/ 50 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [2] or GPIO[23] or SSCLK1SSCLK1 (for SSIF1)

Pin Name Pin No. I/OInput Output Pin Description

Type Type (Note: Active low signals have an "n" pin name ending.)

5 – 3

UX-108U/178U/188UFO-375U

XFC3 (IC3) Terminal descriptions

Operator Panel InterfaceOPI[3]/GPIO[24] 49 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [3] or GPIO[24]LEDCTL 55 O − 4XC Indicates outputs OPO[7:0] are for LEDs.LCDCS 54 O − 1XC LCD chip select.

General Purpose I/OGPIO[0] 94 I/O H 2XC (Hysteresis In) GPIO[0].GPIO[1]/SASTXD 93 I/O H 2XC (Hysteresis In) GPIO[1] or SASTXD (for SERIF).GPIO[2]/SASRXD 92 I/O H 2XC (Hysteresis In) GPIO[2] or SASRXD (for SERIF).GPIO[3]/SASCLK 91 I/O H 2XC (Hysteresis In) GPIO[3] or SASCLK (for SERIF).GPIO[4]/CPCIN 90 I/O H 2XC (Hysteresis In) GPIO[4] or Calling Party Control Input.GPIO[5]/SSCLK2 89 I/O H 2XC (Hysteresis In) GPIO[5] or SSCLK2 (for SSIF2).GPIO[6]/SSTXD2 87 I/O H 2XC (Hysteresis In) GPIO[6] or SSTXD2 (for SSIF2).GPIO[7]/SSRXD2 86 I/O H 2XC (Hysteresis In) GPIO[7] or SSRXD2 (for SSIF2).GPIO[8]/FWRn 85 I/O H 2XC (Hysteresis In) GPIO[8] or flash write enable signal for NAND-type flash

memory.GPIO[9]/FRDn 84 I/O H 2XC (Hysteresis In) GPIO[9] or flash read enable signal for NAND-type flash

memory.GPIO[10]/SSSTAT2 83 I/O H 2XC (Hysteresis In) GPIO[10] or SSSTAT2 (for SSIF2).GPIO[11]/BE/ 82 I/O H 1XC (Hysteresis In) GPIO[11] or bus enable or serial port data input forSERINP autobaud detection.GPIO[12]/CS[2]n 80 I/O H 2XC (Hysteresis In) GPIO[12] or I/O chip select [2].GPIO[13]/CS[3]n 79 I/O H 2XC (Hysteresis In) GPIO[13] or I/O chip select [3].GPIO[14]/CS[4]n 78 I/O H 2XC (Hysteresis In) GPIO[14] or I/O chip select [4].GPIO[15]/CS[5]n 77 I/O H 2XC (Hysteresis In) GPIO[15] or I/O chip select [5].GPIO[16]/IRQ[8] 76 I/O H 1XC (Hysteresis In) GPIO[16] or external interrupt 8.GPIO[17]/IRQ[5]n 75 I/O H 1XC (Hysteresis In) GPIO[17] or external interrupt 5.GPIO[18]/IRQ[9]n 74 I/O H 1XC (Hysteresis In) GPIO[18] or external interrupt 9.GPIO[19]/RDY/ 73 I/O H 1XC (Hysteresis In) GPIO[19] or ready signal or Serial port data output forSEROUT autobaud detection.GPIO[20]/ALTTONE 107 I/O H 1XC (Hysteresis In) GPIO[20] or ALTTONE.

MiscellaneousSM[3:0]/GPO[7:4] [103:106] O − 1XC Programmable: scan motor control pins or GPO pins.PM[3:0]/GPO[3:0] [115:118] O − 1XC Programmable: print motor control pins or GPO pins.TONE 119 O − 1XC Tone output signal.

Power, Reference Voltages, Ground-Vref/CLREF 66 I -VR − Negative Reference Voltage for Video A/D or Reference Voltage for the

Clamp Circuit.ADXG 68 I VXG − A/D Internal GND. (NOTE: This pin requires an external 0.22µF decoupling

capacitor to ADGA.)ADGA 69 VADG A/D Analog GroundADVA 70 VADV A/D Analog PowerADGD 72 VADG A/D Digital Ground+Vref 71 I +VR Positive Reference Voltage for Video A/D.VIN 67 I VA − Analog Video A/D input.THADI 65 I TA − Analog Thermal A/D input.

Power and GroundVSS(12) 7,21,28,45, Digital Ground

53,56,64,88,95,108,132,134

VDD(8) 14,32,41,48, Digital Power81,102,123,140

VBAT 63 Battery PowerVDRAM 114 DRAM Battery Power

Pin Name Pin No. I/OInput Output

Pin DescriptionType Type

5 – 4

UX-108U/178U/188UFO-375U

(2) Panel control blockThe following controls are performed by the XFC3.

• Operation panel key scanning

• Operation panel LCD display

(3) Mechanism/recording control block

• Recording control block diagram (1)

Fig. 4

OPERATOR PANEL,

KEYPAD, LEDS & LCD

PANEL/LCD PWB

PRINTER DATA CONTROI & SENSORS

THERMAL HEAD

OPO[7:0]*OPI[3:0]*LEDCTL*LCDCS*

TESTBATRSTNRESETN

STRB[3:0]STRBPOLTHADIPDATPCLKPLAT

TONE/ALTTONETSTCLKREGDMAWAITNSYNCPWRDWNN

PRINTER & SCANNER

MOTOR DRIVERS

MOTORPM[3:0]*

SM[3:0]*

RTC CRYSTAL

SCANNER CONTROLS &

SENSORS

STARTCLK2CLK1CLK1NVIDCTL[1:0]

XINXOUT

MIRONMCSN

SYSCLK

D[7:0]RDN

A[4:0]

WRN

MONOFAX FACSIMILE

MODEM

ANALOG SWITCH

LINE INTERFACE

SPEAKER MICROPHONE

CIRCUIT

TELEPHONE LINE

RX

AT

XA SP

KR

MIC

RIN

SP

KR

LOS

PK

RH

I

SPKRRIN

TX

A2

TX

A1

TXOUTRXIN

XIA

GPIO

DRAM (OPTION)

SCANNER VIDEO

PREPROCESSING

SYNC PORTS (2) (SSIF)

VIN+VREF

–VREF

SSCLK[2:1]*SSTXD[2:1]*SSRXD[2:1]*SSSTAT[2:1]*

SYNC/ASYNC SERIAL PORT

SASCLKSASTXD

SASRXD

GPIOGENERAL PURPOSE I/O

CIS

DEBUGNVDDVDRAMVBATVSS

FLASH MEMORY

WRPROTNFRDN*FRWN*FCLE*FCS[0:2]

D[7:0]RDN

A[23:0]

WRNROMSCN

CS[5:0]N*

TXDATRMODE

RXDAT

TMODECLKINSLEEPN

GPIO

CAS[0,1]N,RASN,DWRN

NOTES:*ALTERNATIVE GPO,GPI OR GPIO LINES

SPEAKERPHONE ONLY

VOICE OR SPEAKERPHONE

EXTENDED FACSIMILE

CONTROLLER XFC-(M)

EX

TE

RN

AL B

US

5 – 5

UX-108U/178U/188UFO-375U

(4) Modem (R96DFXL-CID) block

INTRODUCTIONThe Rockwell R96DFXL-CID MONOFAX modem is a synchronous 9600bits per second (bps) half-duplex modem with error detection and DTMFreception. It has low power consumption and requires only a single +5VDC power supply. The modem is housed in a single VLSI device pack-age.The modem can operate over the public switched telephone network(PSTN) through line terminations provided by a data access arrange-ment (DAA).The R96DFXL-CID is designed for use in Group 3 facsimile ma-chines.The modem satisfies the requirements specified in CCITT recommen-dations V.29, V.27 ter, V.21 Channel 2 and T.4, and meets the binarysignaling requirements of T.30.The modem can operate at 9600, 7200, 4800, 2400, or 300 bps, andalso includes the V.27 ter short training sequence option.The modem can also perform HDLC framing according to T.30 at 9600,7200, 4800, 2400, or 300 bps.The modem features a programmable DTMF receiver and three pro-grammable tone detectors which operate concurrently with the V.21channel 2 receiver.The voice mode allows the host computer to efficiently transmit andreceive audio signals and messages.The modem is available in either a 100-pin plastic quad flat pack (PQFP)or a 64-pin quad in-line package (QUIP).General purpose input/output (GPIO) pins are available for host assignment in the 100-pin PQFP.The modem’s small size, single voltage supply, and low power con-sumption allow the design of compact system enclosures for use in bothoffice and home environments.MONOFAX is a registered trademark of Rockwell International.

FEATURES

• Group 3 facsimile transmission/reception

– ITU-TS V.29, V.27 ter, T.30, V.21 Channel 2, T.4

– HDLC Framing at all speeds

• V.27 ter short train

• Concurrent DTMF, FSK, and tone reception

• Voice mode transmission/reception

• Half-duplex (2-wire)

• Programmable maximum transmit level:

0 dBm to –15 dBm

• Programmable transmit analog attenuation:

0 dB to 14 dB in 2 dB steps

• Receive dynamic range: 0 dBm to –43 dBm

• Programmable dual tone generation

• Programmable tone detection

• Programmable turn-on and turn-off thresholds

• Programmable interface memory interrupt

• Diagnostic capability

– Allows telephone line quality monitoring

• Equalization

– Automatic adaptive equalizer

– Fixed digital compromise equalizer

• DTE interface: two alternate ports

– Selectable microprocessor bus (6500 or 8085)

– CCITT V.24 (EIA-232-D compatible) interface

• TTL and CMOS compatible

• Low power consumption: 275 mW (typical)

• Single Package

– 100-pin PQFP

– 64-pin QUIP

• Single +5VDC power supply

• Software compatible with R96MFX, R96EFX, R96SHF, and R96VFXmodems

5 – 6

UX-108U/178U/188UFO-375U

R96DFXL-CID (IC2) Hardware Interface Signals

Pin Signals – 100-Pin PQFPPin No. Signal Name I/O Type

1 GP03 IA/OB2 GP04 IA/OB3 GP05 IA/OB4 GP06 IA/OB5 GP07 IA/OB6 0VD2 GND7 0VD2 GND8 D7 IA/OB9 D6 IA/OB

10 D5 IA/OB11 D4 IA/OB12 D3 IA/OB13 D2 IA/OB14 D1 IA/OB15 D0 IA/OB16 0VD2 GND17 0VA GND18 RAMPIN R19 NC20 NC21 0VA GND22 +5VD2 PWR23 0VD1 GND24 SWGAINI R25 ECLKIN1 R26 SYNCIN1 R27 NC28 NC29 NC30 0VA GND31 NC32 NC33 NC34 DAIN R35 ADOUT R36 BYPASS IC37 RCVI R38 TXLOSS3 IC39 TXLOSS2 IC40 TXLOSS1 IC41 NC42 NC43 0VA GND44 TXOUT AA45 RXIN AB46 +5VA PWR47 0VA GND48 AGD R49 AOUT R50 0VD1 GND51 NC52 IRQ OC53 WRITE-R/W IA54 CS IA55 READ-φ2 IA56 RS4 IA57 RS3 IA58 RS2 IA59 RS1 IA

Pin No. Signal Name I/O Type60 RS0 IA61 GP13 IA/OB62 NC63 GP11 IA/OB64 RTS IA65 EN85 R66 0VD2 GND67 PORI ID68 XTLI R69 XTLO R70 XCLK OD71 YCLK OD72 +5VD1 PWR73 DCLK1 R74 SYNCIN2 R75 GP16 IA/OB76 GP17 IA/OB77 0VD2 GND78 CTS OA79 TXD IA80 0VD2 GND81 0VD2 GND82 DCLK OA83 EYESYNC OA84 EYECLKX OA85 EYECLK OA86 EYEX OA87 ADIN R88 DAOUT R89 0VD2 GND90 EYEY OA91 GP21 IA/OB92 0VD2 GND93 GP20 IA/OB94 GP19 IA/OB95 RXD OA96 RLSD OA97 0VD2 GND98 RCVO R99 SWGAINO R100 GP02 IA/OB

Notes:1. NC = No connection; leave pin disconnected (open).2. I/O Type: = Digital signals: see Table 9;

Analog signals: see Table 10.3. R = Required modem inter-connection; no connection

to host equipment.

5 – 7

UX-108U/178U/188UFO-375U

[3] Circuit description of TEL/LIU PWB

(1) TEL/LIU block operational description

1) Block diagram

2) Circuit description

The TEL/LIU PWB is composed of the following 7 blocks.

1. Speech circuit section

2. Dial transmission section

3. Speaker amplifier section

4. Ringer circuit section

5. Externally connected TEL OFF HOOK detection circuit

6. CI detection circuit

7. Signal/DTMF transmission level & receiving level

Fig. 5

3) Block description

1. Speech circuit section

• The receiver volume is an electronic volume type, this model isswitch in 3 steps.

2. Dial transmission section

• D.P. transmission: The CML relay is turned on and off for control inthe DP calling system. (Refer to the attached sheet.)

• DTM transmission: It is formed in the modem, and is output.

3. Speaker amplifier section

• The volume of the ringer sound/speaker sound is controlled with2-bit signal of VOLA and VOLB, and the sound switch is controlledwith BZ CONT.

4. Ringer circuit section

• The ringer sound is formed in the tone of 1-chip engine when CIsignal is detected. The amplifier circuit drives the speaker of themain body.

CONTROL PWBTEL/LIU PWB

HL

TX OUT

RX IN

1

0

0

1

HS DETECTOR

CI DETECTOR

SIGTX

SIGRX

CML GAIN-CTX CONT

MODEM (R96DFXL-CID)

VO

L B

VO

L A

RC VOL1

RC VOL2

TEL IN

TEL OUT

0

1

SP AMP

SP OUT

VOL BVOL A

RC VOL2

BZ CONTSP MUTETEL MUTECIHS

BZOUT

RC VOL1GAIN-CTXCONTCML

XFC3

H

L

HL

CML

TEL LINE

EXT.

HANDSET

SPEAKER

5 – 8

UX-108U/178U/188UFO-375U

5. Externally connected TEL OFF HOOK detection circuit section

• The circuit current detection is turned on together with OFF HOOKof main body or OFF HOOK of externally connected TEL. ON ofCML OFF is judged as OFF HOOK of externally connected TEL.

6. CI detection circuit

• CI is detected by the photocoupler which is integrated in series inthe primary side TEL circuit well proven in the existing unit.

7. Signal/DTMF transmission level & receiving level

• Signal transmission level setting: ATT -10 dB Circuit output: -12dBm.

• DTMF transmission level setting: HF -3.5 dBm LF -5.0 dBmThus, set the level.

• Attenuation in the LIU section of the receiving level is degigned at-6 dBm. (The modem and circuit error are not included.)

Signal Name Description

CML Line connecting relay and DP generating relay(The circuit is located H: Line makein the TEL/LIU PWB.) L: Line break

SP MUTE Speaker tone mute control signal(The circuit is located H: Muting (Power down mode)in the TEL/LIU PWB.) L: Muting cancel (Normal operation)

Handset reception mute control signalTEL MUTE H: Muting

L: Muting cancel

Handset receiver volume control signal

RCVOL1 RCVOL2

(The circuit is locatedin the control PWB.) Three stage switching.

Note: The DTMF sending listed above is DTMF signalsending in the handset OFF-HOOK mode.

Speaker volume control signal,VOL A VOL A VOL B matrixVOL B

(The circuit is locatedin the control PWB.)

TXCONTTXOUT mute signal

(The circuit is locatedH: Signal sending, when transmitting

in the control PWB.)L: During reception, transmission mute,

(during standby)

GAIN-C Reception gain switching signal(The circuit is located H: When connected to line, 1: 1 gainin the control PWB.) L: When not connected to line, HIGH gain

BZCONT Speaker output signal switching(The circuit is located H: Buzzer signal outputin the control PWB.) L: When monitoring line signal

Volume High Middle DTMF sending and LOW

RCVOL1 H L L

RCVOL2 L H L

VOL A VOL BRING./

Buzzer DTMFReceiving

H H — — —H L High — High

L H Middle — MiddleL L Low Fixed Low

7. Signal selection

The following signals are used to control the transmission line of TEL/FAX signal. For details, refer to the signal selector matrix table.

[Control signals from output port]

5 – 9

UX-108U/178U/188UFO-375U

(Example: TEL speaking)

NO Signal Name (CNLIU) NO Signal Name (CNLIU)

1 TELOUT 7 RXIN

2 TELIN 8 TXOUT

3 TELMUTE 9 CML

4 CI 10 +24VA

5 HS 11 +5V

6 RHS 12 DG

Fig. 6

Signal Name Function

RHSH: The handset is in the on-hook state.

L: The handset is in the off-hook state.

CI Incoming call (CI) detection signal

HS

H: The handset or external telephone is in the

on-hook state.

L: The handset or external telephone is in the

off-hook state.

[Signals for status recognition according to input signals]

Signal Name Function

TEL IN Receiving signal from line or modem

TEL OUT Transfer signal to line

SPOUT Speaker output signal

TXOUTTransmission (DTMF) analog signal output

from modem

RXINReception (DTMF, others) analog signal input

into modem

[Other signals]

CONTROL PWBTEL/LIU PWB

TEL LINE

EXT.

HANDSET

SPEAKER

HL

TX OUT

RX IN

1

0

0

1

HS DETECTOR

CI DETECTOR

SIGTX

SIGRX

CML GAIN-CTX CONT

MODEM (R96DFXL-CID)

VO

L B

VO

L A

RC VOL1

RC VOL2

TEL IN

TEL OUT

0

1

SP AMP

SP OUT

VOL BVOL A

RC VOL2

BZ CONTSP MUTETEL MUTECIHS

BZOUT

RC VOL1GAIN-CTXCONTCML

H

L

HL

CML

XFC3

5 – 10

UX-108U/178U/188UFO-375U

[4] Circuit description of power supply PWB

1. Block diagram

2-1. Noise filter circuitThe input noise filter section is composed of L and C, which reducesnormal mode noise from the AC line and common mode noise to the ACline.

2-2. Rectifying/smoothing circuitThe AC input voltage is rectified by diode D1, 2, 3, 4 and smoothed bycapacitor C5 to supply DC voltage to the switching circuit section.

Power thermistor TH1 suppresses inrush current at power switch-on.

2-3. Switching circuitThis circuit employs the self excited ringing choke convertor (RCC) sys-tem. In this system, the DC voltage supplied from the rectifying/smooth-ing section is converted into high frequency pulses by ON/OFF repeti-tion of MOS FET Q1.

Energy is charged in the primary winding of T1 during ON period of Q1,and discharged to the secondary winding during OFF period.

The output voltage is controlled by adjusting ON period of Q1 whichchanges charge time of C9 through operation of photo-coupler PC1 from+24V output.

[5] Circuit description of CIS unit

1. CISCis is an image sensor which puts the original paper in close contactwith the full-size sensor for scanning, being a monochromatic typewith the pixel number of 1,728 dots and the main scanning density of8 dots/mm.

It is composed of sensor, rod lens, LED light source, light-conductiveplate, control circuit and so on, and the reading line and focus arepreviously adjusted as the unit.Due to the full-size sensor, the focus distance is so short that the setis changed from the light weight type to the compact type.

Fig. 8

Fig. 7

The overcurrent protection is performed by bringing Q1 to OFF statethrough detection of voltage increase in the auxiliary winding of T1 byZD2 and R9.

The overvoltage protection is performed by operating the overcurrentprotection circuit through destruction of zener diode ZD4 and short-circuiting of load.

2-4. +5V circuitEach DC voltage supplied by rectifying the output of transformer T1 withdiode D8 is stabilized by 3-terminal regulator IC1.

2-5. VTH circuitVTH output is supplied through the relay RY1.Relay RY1 is operated by VTH-ON signal.

5ms

2µs0V

2V(TYP)(White original paper)

Approx.5VøT

CISCLK

VO

5 – 11

2. WaveformsThe following clock is supplied from XFC3 of the control board, andVO is output.

NoiseFilter

Circuit

RectifyingSmoothing

CircuitSwitching

Circuit(RCC system)

RegulaterCircuit

+5V

+24V

AC IN

Photo Coupler

F11.25A/250V

F34A/72V

6 – 1

UX-108U/178U/188UFO-375U

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT[1

] Con

trol

PW

B c

ircui

t1/

6M

ain

cont

rol b

lock

126 4 35

BD

EF

GI

HC

A

BD

EF

GI

HC

A

126 4 35

TΦ

TΦ

(*1) UX

-108

U

UX

-178

U/1

88U

/FO

-375

U

MO

DE

L

N.M

.

470Ω

R10

5

N.M

.

30KΩ

R10

6

R239 120

107 73 74 75 77 78 79 80 83 84 85 86 87 89 91 92 94 96 97 99 98 101 33 34 35 36 29 31 37

GP

IO20

GP

IO19

GP

IO18

GP

IO17

GP

IO15

GP

IO14

GP

IO13

GP

IO12

GP

IO10

GP

IO9

GP

IO8

GP

IO7

GP

IO6

GP

IO5

VID

CT

L0V

IDC

TL1

CLK

1C

LK2

ST

AR

T

ST

RB

3S

TR

B2

ST

RB

1S

TR

B0

PC

LK

PLA

TS

TR

BP

OL

ADGD72

ADGA

68ADXG

1028148

14

21

28

45

53,56

64,88

DG

95,108

132

7,134

58

VSS

129131

TESTDEBUG

135

RESET

133130

SYSCLK

136137138139141142143

1 2 3 4 5 6 8 9 10 11 12 13 15 16 19 20 22 23 25 26 27 128

127

120

122

121

126

124

125

113

112

111

109

110

61

6260

59

118117116

114

106105104103

52515049

5447

44

A23

A22

A21

A20

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

BATRST

PWRDWNXOUT

XIN

GPO0GPO1GPO2GPO3

OPI2

OPO2

SM0SM1SM2SM3

OPI0OPI1

OPI3

LCDCSOPO0

CNPN-13SEN2

IC3

XF

C3

70ADVA

41

TSTCLK

144

+5V

76G

PIO

16(6

-2H

)S

PM

UT

E

(4-4

C)

CS

WI

(5-5

F)

VT

HO

N82

GP

IO11

(4-4

C)

(4-5

C)

FR

SN

SI

CN

LIU

A-5

OR

GS

NS

I

CN

LIU

A-4

HS

CI

CN

LIU

A-9

93C

NLI

UA

-3C

NLI

UA

-6

CN

CIS

-5C

NC

IS-4

CN

TH

-12

CN

TH

-11

OPO3OPO4

4342

OPO1 46

CNPN-12SEN3

CNPN-11SEN4

CNPN-14SEN1CNPN-15SEN0CNPN-10E

KEN4AKEN3AKEN2AKEN1A

RA7 470 x 4

TONE 119

(5-5F)TPB(5-5F)TPA

BZOUT (6-1H)

63VBAT

RESET

VBT

R15

5 10

M X2 32.768kHz

C4

4.7/

50R

126

100K C

5 10

/50

DG

17 18A

9A

8A

7A

6A

5A

4

A2

A1

A0

RD

WR

RO

MC

SC

S1

MC

SS

YN

CR

EG

DM

AW

AIT

RA

SC

AS

0C

AS

1D

WR

WR

PR

OT

A B

A16

A15

A14

A13

A12

A11

A10 A9

A8

A7

A6

A5

A4

A3

A2

A1

A0

32

DG

C12

9 1

+5V

C

DG

H I J

RA3 470 x 4

90G

PIO

4

100

CLK

1

30P

DA

T

24A

3

D E F G

57C

S0

K

GP

IO3

GP

IO2

GP

IO1

GP

IO0

10K

10K

10K

10K

10K

10K

R10

6

10K

R13

0 3.

3K

10K(*1)

RA

1

RA

1

RA

1

(3-2

A)

MD

MR

ST

(4-4

C)

CU

T1I

CN

LIU

B-4

CN

TH

-6

MP

XB

RA

NK

(4-3

C)

PS

NS

NI

(3-1

D)

BY

PA

SS

(4-5

C)

DR

SN

SI

CM

LT

ELM

UT

ER

HS

R12

7 47

0

R12

8 47

0

R20

5 47

0R

161

470

R20

0 47

0R

230

470

R23

4 47

0

R10

5

R22

9 47

0R

233

470

R23

1 47

0R

A1

ST

RB

3

CN

TH

-4S

TR

B2

CN

TH

-3P

CLK

DA

TA

CN

TH

-14

CN

TH

-15

CN

TH

-13

LAT

CH

R15

6 Z

2145

R17

4 Z

2145

R18

6 47

0R

170

470

R16

9 47

0R

187

470

R16

8 27

0R

185

270

R18

4 27

0

ST

RB

4

CIS

CLK

ST

RB

1

DGDGDGDGDGDG

R14

9 10

K

C160C161C162

C166

C163C164C165

OPO5 40

OPO6 39

OPO7 38

55LEDCTLCNPN-1CNPN-2CNPN-3CNPN-4

R172 470

L104 Z2145

RA6 470x4

DG

(4-1D)

DG

DG

DG

C111 2200P

C127 22P

C128 22P

666765

–VREF/CLREFVIN

THADI

+VREF 71

VDRAM

(5-2H)THADI(5-5D)VIN(5-4D)–VREF(5-4D)+VREF

(5-5F)TPB(5-5F)TPA

(6-4A)GAINC(6-4H)BZCONT(5-2A)VREFCONT

(6-6A)TXCONT

DGDGDG

DG

C167 1000PC168 1000PC169 1000PC170 1000P

C171 1000P

RA2 470x4115

DGC

105

1

DG

+5V

(2-3

A)(

3-3A

)(2

-4D

)(3-

2A)

(2-4

A)

(2-4

D)

CE

1

(3-3

A)

MC

S

RD

WR

RD

MC

S

(2-6

A)(

3-4A

)

A[1

6~0]

69C11

6 1

140123

C11

2 1

DG

DG

DG

DG

DG

DG

DG

C11

0 1

C12

6 1

C11

4 1

C10

4 1

C11

3 1

C10

3 1

C11

5 1

DG

SYSCLK(3-2A)

RA4 270 x 4

D7D6D5D4D3D2D1D0

RA5 270 x 4

D7D6D5D4D3D2D1D0

(2-6

A)(

3-3A

)D

[7~

0]

MIRQ(3-2A)

R125 10K

C101 1000P

R103 10K

R102 10K

R104 10K

MIRQ

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VDDVDDVDDVDDVDDVDDVDDVDD

LM

N

R23

6 20

0

R23

7 27

0

22P

x7

6 – 2

UX-108U/178U/188UFO-375U

Mem

ory

bloc

k2/

6

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

A16

21A

1520

A14

2919

A13

2818

A12

17A

1125

15A

1023

14A

926

13A

827

A7

A6

31A

532

A4

1A

3A

210

A1

1116

A0

12 22 24

1IO

819

26IO

718

A14

2

A14

IO6

17A

13

23

A13

IO5

16A

12

21

A12

IO4

15A

11

24

A11

IO3

13A

10

25

A10

IO2

12A

9

3

A9

IO1

11A

8

4

A8

A7

5

A7

A6

6

A6

A5

7

A5

VD

D28

A4

8

A4

VS

S14

A3

9

A3

A2

10

A2

A1

A0

20

A0

27W

E22

CS

2/O

E

A[1

6~0]

(1-5

I)

D[7

~0]

(1-6

I)

(1-3

I)

RD

(1-3

I)

+5V

DG

C14

0 0.

1

D7

D6

D5

D4

D3

D2

D1

D0

IC8

27C

010

2A

16D

Q8

3A

15D

Q7

A14

DQ

6A

13D

Q5

4A

12D

Q4

A11

DQ

3A

10D

Q2

A9

DQ

1A

85

A7

6A

6(A

17)

7A

5V

CC

8A

4V

PP

9A

3A

2A

1G

ND

A0

E G

IC5

SR

M2B

256S

LMX

70

A1

CS

1

D7

D6

D5

D4

D3

D2

D1

D0

VB

T

DG

C12

5 0.

1

WR

(1-3

I)C

E2

(4-1

D)

CE

1(1

-3I)

VB

T

R14

6 22

K

R12

0

R11

9 0

N.M

.

RO

MC

S

6 – 3

UX-108U/178U/188UFO-375U

Mod

em b

lock

3/6

126 4 35

BD

EF

GI

HC

A

BD

EF

GI

HC

A

126 4 35

(*1) UX

-108

U

UX

-178

U/1

88U

/FO

-375

U

MO

DE

L

10K

Ω

N.M

.

R13

7

N.M

.

10K

Ω

R23

8

+5V

D7

A0

C11

7 0.

01

R11

3 27

0

D6

D5

D4

D3

D2

D1

D0

A1

A2

A3

A4

56 57 58 59 60

RS

4R

S3

RS

2R

S1

RS

0

8D

79

D6

10D

511

D4

12D

313

D2

14D

115

D0

54C

S55

RE

AD

53W

RIT

E52

IRQ

70X

CLK

(12M

)71

YC

LK(6

M)

64R

TS

78C

TS

79

DC

LK82

DC

LKI

73

RX

D95

TX

D

96R

LSD

67P

OR

I65

EN

85

DG

617576949391

72

235067

1666778081899297

22

L102

Z

2145

C11

9 0.

1

GP13GP16GP17GP19GP20GP21

+5VD1

0VD10VD10VD20VD20VD20VD20VD20VD20VD20VD20VD20VD2

C13

1 1

+5VD2+5V

L103

Z

2145

+5V

A0V

A0V

A0V

A0V

A0V

A

46

AD

OU

TA

DIN

RC

VO

RC

VI

RA

MP

INA

GD

SW

GA

IN0

SW

GA

IN1

N.C

.N

.C.

N.C

.

17 21 30 43 47

C10

9 0.

1

35 87 98 37 45 49 18 48 42 44 88 99 24 19 27 29 31 32

C3

47/2

5

R13

6 3

+5V

R11

4 0

MA

G

N.C

.33

SIG

RX

5432110063

383940

R132

8525832674848690

68

GP07GP06GP05GP04GP03GP02GP11

TXLOSS2TXLOSS1

EYECLKECLKIN1

EYESYNCSYNCIN1SYNCIN2EYECLKX

EYEXEYEY

XTLI

RCVOL1RCVOL2

VOLA(6-1H)

CNLIUB-5

(6-1H)(6-2A)(6-2A)

R13

5

MA

GX

1 24

.000

14M

Hz

C10

7 18

P

R11

0 12

0

C10

6 15

P

R11

1 20

0

69XTLO

IC2

R96

DF

XL-

CID

N.C

.N

.C.

N.C

.

DG

(6-3

A)

MPXCVOLB

DG

D[7

~0]

RD

WR

(1-6

I)

(1-3

I)(1

-3I)

(1-3

I)

DG

C11

8

R11

5 0

(5-1B)

DG

62N.C.

R13

7

LEDON

N.M

.

DG

C13

0

N.M

.

51

RX

IN

41

DA

IN34

AO

UT

N.C

.2820

N.C

.N

.C.

N.C

.

DA

OU

TT

XO

UT

MA

G

C10

8 1

C12

0 39

0P

C12

1 0.

1R

112

47.5

K

AG

D(6

-3A

)

SIG

TX

(6-5

A)(

6-5E

)

36BYBASS

N.M

.

DG

R162 470R157 470R158 470R159 470

R160

N.M.

N.M.CNLIUB-3MPXA

MIR

Q(1

-6F

)

A[4

~0]

(1-5

I)

SY

SC

LK(1

-6F

)

MD

MR

ST

(1-5

A)

MC

S

R10

9 47

0

MA

GR12

9 10

K

TXLOSS3

(1-4A)BYPASSR166 10K

R13

1 10

K

(6-2A)

L105

Z

2145

R23

8

(*1)

6 – 4

UX-108U/178U/188UFO-375U

Oth

er b

lock

4/6

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

IC10

0 P

ST

596C

NR

+5V

35

4

OUT

GN

D

2

MR

ST

R12

1Q

101

(2-4

D)

CE

2

VC

C

R11

7

(1-1

F)

RE

SE

T

R10

1 1K

SU

B

1C

100

1

E

BC

– +

(*1) UX

-108

U

UX

-178

U/1

88U

/FO

-375

U

MO

DE

L

N.M

.

470Ω

R19

6

N.M

.

0.1µ

C13

9

N.M

.

2PIN

CN

CU

T1

N.M

.

100Ω

R10

0

N.M

.

ITR

9606

PI1

+5V

R21

4 27

0C

NP

N-8

OR

GS

NS

R21

2 5.

6K

R20

7 3.

3K321

R21

5 30

K

IC10

29

04

(1-4

A)

OR

GS

NS

1

DG

C15

2 0.

1

8 4

DG

DG

(1-4

A)

DR

SN

S1

(1-4

A)

(1-5

A)

(1-4

A)

CN

PN

-9F

RS

NS

CN

CS

W-1

CS

W

CN

CU

T1-

1C

UT

1

C12

4 0.

1R

145

470

DG

C13

3 0.

1R

171

Z21

39

DG

C15

1 0.

1R

206

470

DG

C13

9

DG

FR

SN

S1

CS

WI

CU

T1I

DG

SW

1 D

OO

R S

W

(1-4

A)

PS

NS

I+

5VR

100

(*1)

13

24

PI1

DG

DG

PS

NS

DG

DG

HO

LBA

T-1

BT

+

R22

8 5.

6K

CN

PW

-2+

5V

HO

LBA

T-2

BT

+

HO

LBA

T-3

DG

BA

T1

CR

2032

DG

D10

1 R

B70

5D

+5V

DG

C15

9 0.

1

<V

BT

>

VB

T

+5V

CN

PW

-1D

G

DG

CN

LIU

A-1

1+

5V

CN

LIU

A-1

2D

G

CN

PN

-7+

5V

CN

PN

-5D

G

CN

PN

-6D

G

CN

CU

T1-

2D

G

C15

8 0.

1C

9 47

/25

DG

CN

PW

7+

24V

CN

PW

-4M

G

CN

PW

-5M

G

CN

PW

-6M

G

CN

LIU

A-1

0+

24V

A

C14

9 0.

1C

10

22/5

0

R19

9

+5V MG

N.M

.

+24

VA

DG

C7

100/

50

DG

FG

R19

7

N.M

.

N.M

.

(*1)

(*1)

R19

6

N.M

.

(*1)

6 – 5

UX-108U/178U/188UFO-375U

Vid

eo p

roce

ssin

g/M

otor

driv

e th

erm

al b

lock

5/6

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

– +

–+

(*1) UX

-108

U

UX

-178

U/1

88U

/FO

-375

U

MO

DE

L

N.M

.

RN

C14

02

Q10

3

N.M

.

30KΩ

R21

7

N.M

.

2SC

1858

Q1

N.M

.

27Ω

/1W

R1

0Ω 1000

P

R23

5

0Ω

30KΩ

R18

8

N.M

.

33KΩ

R20

9

N.M

.

200Ω

R21

0

N.M

.

0ΩR22

7

+5V

R19

0 5.

1KQ

101

2SC

2412

Q10

2 2S

A10

36

R18

9 1.

5K

DG

DG

DG

R19

1 10

K

CN

CIS

-1V

O(1

-1F

)V

IN

C14

1 10

00P

+5V

R21

8 10

K

R23

2 30

K

DG

IC9

2902

321

(1-1

F)

VR

EF

+

(1-1

F)

VR

EF

–

DG

+5V

+24

V

+5V

CN

CIS

-3+

5V

CN

CIS

-2D

G

CN

CIS

-7+

24V

CN

CIS

-6G

LED

C14

2 1

R18

8

IC10

29

04

657

R20

9R

217

R21

0

R22

7

R1

R23

5

Q1

Q10

3

E

BC

DG

DG

DG

(1-1

E)

VR

EF

CO

NT

(5-5

H)

LED

ON

CO

M9

11B

1C16

22B

2C15

33B

3C14

44B

4C13

55B

5C12

66B

6C11

77B

7C10

8E

TP

AT

PB

(1-1

E)

TP

A(1

-1E

)

TP

B(1

-1E

)(1

-1E

)

(1-4

A)

VT

HO

N

(3-1

D)

LED

ON

IC7

ULN

2003

A

VM

TC

NM

T-5

VM

TC

NM

T-6

TP

AD

CN

MT

-1T

PB

DC

NM

T-2

TP

AD

CN

MT

-3T

PB

DC

NM

T-4

VT

HO

NC

NP

W-3

LED

ON

(5-1

B)

+24

V

D1

RD

22F

B3

FU

100

1CP

S07

MG

MG

VT

HC

NP

W-8

VT

HC

NT

H-1

CN

TH

-2C

NT

H-1

6

MG

CN

TH

-7C

NT

H-8

CN

TH

-9

VT

HC

NP

W-9

VT

HC

NP

W-1

0R

204

22K

MG

+5V

CN

TH

-10

TH

AD

1(1

-1F

)

TH

1C

NT

H-5

MG

MG

C15

0 0.

1R

201

20K

C8

10/5

0R

202

470K

+5V

<V

IN>

<V

O>

<D

G>

VT

H

MG

VT

H

MG

(*1)

NO

TE

:T

hese

mar

ks a

re a

ll sa

fety

-crit

ical

par

ts.

6 – 6

UX-108U/178U/188UFO-375U

Ana

log

sign

al b

lock

6/6

126 4 35

BD

EF

GI

HC

A

BD

EF

GI

HC

A

126 4 35

– +

– +

– +

– +

1214

13

TE

LOU

TC

NLI

UA

-1

R19

5 86

.6K

C14

7 68

0P

C13

2 1

IC6

4053

VR

EF

TX

CO

NT

(1-1

E)

01

89 10

IC9

2902

R22

5 10

0K

+5V

R27

4 3.

3KC

157

1

+5V

16 7 8

IC6

4053

C13

4 0.

1

SIG

TX

(3-3

H)

R18

3 1K

R18

2

R18

1 1K

C13

6 0.

1N

.M.

DG

R19

4 17

.4K

R22

4 10

K

C14

6 1

TX

OU

TC

NLI

UA

-8

DG

DG

SIG

TX

(3-3

H)

R19

2 86

.6K

C14

4 10

00P

76 5

IC9

2902

SIG

RX

(3-3

H)

+5V

D10

0 1S

S35

5R

216

3K

MA

G

AG

D(3

-3H

)

R22

1 0

C6

10/5

0

54

3

9 IC6

4053

01

GA

INC

(1-1

E)

RX

INC

NLI

UA

-7

R17

8 3.

3K

R17

7 62

K

R17

5 0

EX

SIG

CN

LIU

B-1

C14

5 0.

1

R18

0N

.M.

RC

VO

L1(3

-1C

)

R22

2 47

K

1413 12

IC4

4066

+24

VA R21

9 1.

5K

C15

4 0.

1

R22

3 47

K

R22

0 10

K

TE

LIN

CN

LIU

A-2

DG

DG

C15

5 10

00P

DG

C15

6 0.

1

114

RC

VO

L2C

NLI

UB

-2

RC

VO

L1C

NLI

UB

-6

DG

VR

EF

+5V

C14

8 0.

1

RC

VO

L2(3

-1C

)

R21

1 33

K

R16

5 30

K

R16

4 2K

IC4

4066

IC9

2902

13

12

5

34

R21

3 33

KC

153

1

215

1

10

IC6

4053

0 1

DG

R17

9 1K

DG

C14

3 47

00P

IC4

4066

R14

1 10

K

R13

8 47

K

IC4

4066

89

1011

C13

5 0.

01R

176

3KC

138

0.01

R14

2 22

0K

DG

DG

R16

3 20

K

R14

3 3K

C2

1/50

5 IC1

MC

3411

98

71

32

46

R13

9 10

K

+5V

R14

0 10

0KR

116

220K

C12

3 22

0P

DG

C1

47/2

5

SP

+C

NS

P-1

SP

–C

NS

P-2

SP

MU

TE

(1-5

A)

BZ

CO

NT

(1-1

E)

VO

LB(3

-1D

)

VO

LA(3

-1C

)

BZ

OU

T(1

-1F

)

DG

VC

C

GN

DV

EE

EN

AB

LE

DG

6

+5V

14 7

IC4

4066

C12

2 0.

1

DG

VC

C

GN

D

11

C13

7 0.

1

R19

3 20

K

6 – 7

UX-108U/178U/188UFO-375U

Control PWB parts layout (Top side)

6 – 8

UX-108U/178U/188UFO-375U

Control PWB parts layout (Bottom side)

6 – 9

UX-108U/178U/188UFO-375U

[2] T

EL/

LIU

PW

B c

ircui

t

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

– +

– +

– +

N.M

. N.M

.

VR

EF

+24

V

MJ1

-3

CBM

MJ1

-4

MJ2

-3

MJ2

-4

TIP

RIN

G

EX

T-T

EX

T-R

C7

4.7/

50

R22

3.

3K

T1

2128

C8

0.03

3

ZD

5 H

Z2C

1

ZD

4 H

Z2C

1

IC1

2904

L2R

21

620

C5

0.01

D4

1SS

270

C15

10

00P

C17

22

0P7

6

R7

JP

D2

1SS

270

Q2

2SC

1815

+5V

L1

+5V

R13

1.

5K

IC1

2904

BB

C

Q1

DT

C11

4

E

C12

4.

7/50

R2

150

CM

L

Q3

DT

C11

4

D3

1SS

270

+5V

C19

0.

022

C2

0.82

R6

22K

R5

22K

(1/

2W)

R19

10

K

CN

LIU

-8T

XO

UT

C11

4.

7/50

R17

10

K

C4

2200

P

2 31

R16

10

K

R10

10

K

R9

10K

C3

2200

P

VR

EF

CN

LIU

-7R

X IN

ZD

3 H

Z27

PC

2 T

LP52

1-1

CN

LIU

-9C

ML

BE

CN

LIU

-11

IC1

2904

8 4

MJT

EL-

1T

X

C14

4.

7/50

R11

1.

5KL6

MJT

EL-

4T

X

MJT

EL-

3R

X

C1

2200

P

CN

LIU

-1T

ELO

UT

5

C16

10

00P

R12

1K

C13

2.

2/50

R15

3.

3K

R14

15

K

C18

33

00P

L7

N20

24

MJT

EL-

2R

X

D1

1SS

270

E

R1

CN

LIU

-3T

EL

MU

TE

N.M

.C

NLI

U-1

0

CN

LIU

-12

+24

V

+5V

VA

1

VA

2

R8

JP

C20

N.M

.

R20

15

KV

RE

F

CN

LIU

-2T

ELI

N

C9

1000

P

HS

CN

LIU

-5

HO

OK

SW

CN

LIU

-6R

HS

R4

91 R3

30ZD

2 H

Z2C

1Z

D1

HZ

2C1

PC

1 P

C81

4X

L4 L5

CM

L

C10

10

00P

PC

2 T

LP52

1-1

CI

CN

LIU

-4

PC

1 P

C81

4

VR

EF

R18

1K

R23

1K

C21

C6

22/5

0

L3

DG

4 3 4 3

42

31

Q

AR

1 R

A39

1PV

62E

RZ

V5D

471x

2

N.M

.

N.M

.

N.M

.

N.M

.

AR

G

N.M

.

6 – 10

UX-108U/178U/188UFO-375U

TEL/LIU PWB parts layout

6 – 11

UX-108U/178U/188UFO-375U

[3] P

ower

sup

ply

PW

B c

ircui

t

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

4 3

RL1

N40

04 x

4

C5

220/

200

R2

0.18

C7

1000

P

INO

UT

GN

D

L1

C1

0.1

V1

240V

F1

1.25

A/2

50V

CN

1

Q1

FS

10K

M

R5

180K R6

150K

R7

82K

D5

ER

A22

-06

C6

0.01

T1

D7

S3L

20U

-400

4P15

C16

22

00P

C15

68

0/35

ZD4 RD30FB3

R19

R12

2.

2KQ

3 2S

C17

40S

PC

1 P

S25

01-1

R13

27

0R

14

3.9K V

R1

470

R15

12

0

7 10

VM

IC1

BA

178M

05T

13

2

C18

47

0/16

D8

SR

140

R10

22

D6

IS20

76A

PC

1 P

S25

01-1

1 2

C4

AC

LA

C N

R3

8.2k

C9

0.06

8

R4

100

Q4

2SC

1741

AS Q

2 2S

C26

55-Y

C10 1000P

C11 1000P

ZD2 RD3.9ESAB2 R

9 68

0

R8

680

C8

0.01

C12

47

00P

C17

6M

G

VT

H

MG

MG

5 4

+5V

2

DG

1CN

2

31

R1

560K

C3

V2

D3

D2

D4

D1

TH

1 8.

2ohm

s

N.M

.

C13

33

00P

R6

680

R11

68

0

C14 1000P

(5)

(1)

(2)

(3)

(6)

(7)

(8)

(4)

C19

1/

50ZD3

RD6.2ESAB2

N.M

.

N.M

.

9V

TH

8V

TH

3V

TH

-ON

FB

1F

3 C

CP

2E10

0

D9

IS20

76A

RY

1 A

JS33

12

6 – 12

UX-108U/178U/188UFO-375U

Power supply PWB parts layout

6 – 13

UX-108U/178U/188UFO-375U

[4] O

pera

tion

pane

l PW

B c

ircui

t

Not

e: S

ince

the

part

s of

this

PW

B c

an n

ot b

e su

pplie

d, c

hang

e it

as a

uni

t.

126 4 35

BD

EF

GI

HC

A

126 4 35

BD

EF

GI

HC

A

CN

PN

-15

CN

PN

-14

CN

PN

-13

CN

PN

-12

CN

PN

-11

SE

N0

SE

N1

SE

N2

SE

N3

SE

N4

KE

N 1

A

CN

PN

-3K

EN

2A

CN

PN

-2K

EN

3A

CN

PN

-1K

EN

4A

CN

PN

-10

E

CN

PN

-7+

5V

CN

PN

-6G

ND

CN

PN

-5

FU

NC

RE

CE

PT

ION

RE

SO

LUT

ION

PLA

Y

RE

MIN

DE

R

CO

PY

DE

LET

E

8 02

D1

D2

D3

D4

D5

D6

D7

D8

D9

11 12 13 1 2 3 4 5 10

A0

A1

A2

A3

9 7 6 14

IC10

1 74

HC

147

CN

LCD

-6C

NLC

D-5

CN

LCD

-3C

NLC

D-2

CN

LCD

-1

C2

22/5

0C

1 0.

022

CN

LCD

-11

LD4

CN

PN

-4

GN

D

CN

LCD G

ND

1 2 3 4 5 6 7 8 9 10 11 12 13 14

+5V

VO

RS

GN

DE N

.C.

N.C

.N

.C.

N.C

.LD

4LD

5LD

6LD

7

CN

PN

KE

N 4

AK

EN

3A

KE

N 2

AK

EN

1A

+5V

GN

DG

ND

OR

GS

NS

FR

SN

SE S

EN

4S

EN

3

DO

WN

01

UP

02

ST

OP

ST

AR

T

5

RE

C

9 #3 6

HO

LD

SP

EA

KE

R

SP

EE

D

RE

DIA

L

07 0903 05

08 1004 06

71 4

D5

1SS

270

D4

1SS

270

D3

1SS

270

D1

1SS

270

CN

LCD

-12

LD5

CN

LCD

-13

LD6

CN

LCD

-14

LD7

D2

1SS

270

CN

LCD

-4R

S

15N

.C.+5V

VC

C

GN

D 816

R1

6.2K R8

1K

VO

+5V

CN

PN

-8

CN

PN

-9

R7

220

SG

266

OR

GS

NS

AC E

K

FR

SN

S

OR

GS

NS

SE

N2

SE

N1

SE

N0

RE

PE

AT

FR

SN

S

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

R10 100K

R5 100K

R9 100K

R3 100K

R2 100K

R4 100K

R11 100K

R12 100K

R6 100K

UX-108U/178U/188UFO-375U

7 – 1

CHAPTER 7. OPERATION FLOWCHART

[1] Protocol

NSF

DIS

NSS

TCF

CED

NSF

DIS

NSS

TCF

RTC

MPS

CFR

RTC

MPS

MCF

RTC

EOP

MCF

MCF

DCN

CFR

TSI

CSI

CSI

TSI

RTC

EOP

MCF

DCN

IMA

GE

SIG

NA

L

Document ejectedRecording papor ejected

Receive sideG3 communication

CED

Transmitter side(Document inserted into document sensor during standby)

To recordingposition

(DCS)

Cut line printed

IMA

GE

SIG

NA

L

Cut line printed

IMA

GE

SIG

NA

LIM

AG

ES

IGN

AL

Next page insertcommand

1st page

Document inserted tothe reading position

(DCS)

UX-108U/178U/188UFO-375U

7 – 2

[2] Power on sequence

2

1YES

YES

CPU initialized

MODEM initialized

STOP key ?

“WAIT A MOMENT” display

START

NO

YES

STAND-BY

3 sec ?NO“MEMORY CLEAR ?” display

NO

YES

STAND-BY

3 sec ?NO

NO

START key ?

COPY key ?

STOP key ?

NO

Memory clear

STAND-BY

21

“MEMORY CLEARED” display

Memory clear

PROCESS CHECK MODE

“MEMORY CLEARED” display

YES

UX-108U/178U/188UFO-375U

8 – 1

CHAPTER 8. OTHERS

[1] Service tools

1. List

Relay board unit

NO. PARTS CODE DESCRIPTION Q’TYPRICERANK

1 C P W B S 2 9 1 5 S C S 1 Relay board unit 1 BN2 P S H E Z 3 3 5 4 S C Z Z Shading wave memory standard paper 1 AD

1 C C N W – 4 7 5 6 S C 0 1 SPEAKER RELAY CABLE 1 AK2 C C N W – 4 7 5 7 S C 0 1 PANEL RELAY CABLE 1 AW3 C C N W – 4 7 5 8 S C 0 1 CIS RELAY CABLE 1 AQ4 C C N W – 4 7 5 9 S C 0 1 HEAD RELAY CABLE 1 AX5 C C N W – 4 7 6 0 S C 0 1 CAM SWITCH RELAY CABLE 1 AK6 C C N W – 4 7 6 1 S C 0 1 CUTTER SWITCH RELAY CABLE 1 AK7 C C N W – 4 7 6 3 S C 0 1 MOTOR RELAY CABLE 1 AP8 Q C N W – 4 7 6 4 S C Z Z PAPER SENSOR RELAY CABLE 1 BB9 V H P R P i – 5 7 4 / / / PHOTO TRANSISTOR [PSNS] 1 AF

10 V R S - T S 2 A D 2 2 1 J RESISTOR (1/10W 220Ω ±5%)[R100] 1 AA11 Q P W B S 2 9 1 5 S C Z 4 EXTENSION PWB 1 AR

NO. PARTS CODE DESCRIPTION Q’TYPRICERANK

PSNS(TP3)

PI1

DG(TP1)

+5V(TP2)

R100

UX-108U/178U/188UFO-375U

Relaycable

CNLIUA

CHECKCONTROLPWB

TEL/LIUPWB

12

1

CNPW

CNLIU

POWERSUPPLYPWB

• The relay cables are used as one pair.• The sensor is wired as shown in the following figure.• The door swich and hook switch are manually operated.

8 – 2

2. Description

2-1. Relay board unit

1. Remove the TEL/LIU PWB, control PWB and Power Supply PWBfrom this unit, and mount the relay board unit instead.

• Before connecting the wiring to the relay board unit, set the testPWB switches to the fixed position.

2. The setting is as follows.

The recording paper sensor (PSNS) is operated by OR of the mechani-cal unit switch and the test PWB switch. When performing installation inthe machine unit, set the test PWB switches to the fixed position.

Mechanical unit PWB to be tested

Actual operation with mechanical unit

Recording papersensor

ON/OFF operation OFF (Photo interrupteris interrupted.)

PWB sensor check

Recording papersensor

ON/OFF operationOFF

POWERSUPPLY

PWB

TEL/LIUPWB

CHECKCONTROL

PWB

DOORSENSORRELAY CABLE

DON'T SEPARATE

UNIT

TP3(PSNS)

TP3(PSNS)

TP1(DG)TP2(+5V)

C K

AE

These cables are connected from the extension boardand the checked control PWB at TP1 thru TP3 (signalsof DG, +5V and PSNS).

EXTENSION PWB

NOTE

UX-108U/178U/188UFO-375U

8 – 3

3. Shading paperThe white and black basis is applied to remember the shading wave-form. Be sure to perform this operation when replacing the battery orreplacing the control PWB. Execute in the shading mode of DIAG mode.

UX-108/178 SERIES SHADING WAVE MEMORY STANDARD PAPER (PSHEZ3354SCZZ)

UX-108U/178U/188UFO-375U

8 – 4

[2] IC signal name

CONTROL PWB UNITIC10: VHiNJM2904M-2 (NJM2904M)

IC7: VHiULN2003AN/ (ULN2003A)

IC5: VHiW24257S7LL (W24257S-70LLT)

IC6: VHiHCF4053M1T (HCF4053B)

–+

– +

1 8 PIN NAME 1. A OUTPUT 2 .A–INPUT 3. A+INPUT 4. GND 5. B+INPUT 6. B–INPUT 7. B OUTPUT 8. V+

(TOP VIEW)

3 6

2 7

4 5

B

A

16 15 14 13 12 11 10 9

1 2 3 4 5 6 7 81B 2B 3B 4B 5B 6B 7B E

1C 2C 3C 4C 5C 6C 7C COM

Signal

A0~A12CE1/CE2

WE

OE

I/O1~I/O8

VCC

GND

N.C.

Address input

Chip enable

Write enable

Write enable

Data I/O

Power source

Ground

No connection

1

2

3

4

5

6

7

8

9

10

11

12

13

14

A14

A12

A7

A6

A5

A4

A3

A2

A1

A0

DQ1

DQ2

DQ3

GND

28

27

26

25

24

23

22

21

20

19

18

17

DQ5

DQ6

DQ7

DQ8

S1

A10

S2

A11

A9

A8

A13

W

VCC

(TOP VIEW)

16

15 DQ4

Pin name

6

11

10

9

12

13

2

1

Inhibit

Controls14

15Common

Out/In

5

Switches In/Out

4

3

A

B

C

X0

X1

Y0

Y1

Z0

Z1

X

Y

Z

VDD: Pin 16 VSS: Pin 8 VEE: Pin7

UX-108U/178U/188UFO-375U

8 – 5

IC9: VHiLM2902D/-1 (LM2902D)

IC4: VHiHCF4066M1T (HCF4066)

IC100: VHiPST596CMT1 (PST596CNR)

IC8: VHi27C1000PC5 (27C010)EP-ROM

IC1: VHiMC34119DR2 (MC34119DR2)

+–

1

A+ –

D2

3

4

14

13

12

11

5

6

7

10

9

8

+–B

+ –C

D OUTPUT

D-INPUT

D+INPUT

GND

C+INPUT

C-INPUT

C OUTPUTB OUTPUT

B-INPUT

B+INPUT

V+

A+INPUT

A-INPUT

A OUTPUT

1

3

5

7

14

12

10

8

IN/OUT

OUT/IN

CONT. B

VDD

CONT. D

OUT/IN

IN/OUT

2OUT/IN

4IN/OUT

6CONT. C

13

11

9

CONT. A

IN/OUT

OUT/IN

VCC

OUT/IN IN/OUTSWA

OUT/IN IN/OUT

SWD

IN/OUT OUT/INSWB

IN/OUT OUT/INSWC

1

2

M/R

SUB

5 VCC

(TOP VIEW)

3GND 4 VOUT

1

2

3

4

5

6

7

8

9

10

11

12

13

VPP

A16

A15

A12

A7

A6

A5

A4

A3

A2

A1

A0

DQ1

32

31

30

29

28

27

26

25

24

23

22

21

20

VCC

PGM

NC

A14

A13

A8

A9

A11

G

A10

E

DQ8

DQ7

14

15

16

DQ2

DQ3

GND

DQ6

DQ5

DQ4

19

18

17

(TOP VIEW)

Pin name

A0~A16

E

G

GND

PGM

DQ1~DQ8

VCC

VPP

Signal

Address input

Chip enable

Output enable

Ground

Program

Data output (Program input)

+5V power

+12.5V power(*)

(*) Only in the program mode

1

2

3

4

CD

FC2

FC1

VIN

8

7

6

5 VO1

VCC

GND

VO2

(TOP VIEW)

UX-108U/178U/188UFO-375U

8 – 6

IC2: VHiR96XFC3CID (96DFXL-CID)

SWGAINI

0VD1

+5VD2

0VA

NC

NC

RAMPIN

0VA

0VD2

D0

D1

D2

D3

D4

D5

D6

GP

02

SW

GA

INO

RC

VO

0VD

2

RLS

Dn

RX

D

GP

19

GP

20

0VD

2

GP

21

EY

EY

0VD

2

DA

OU

T

AD

IN

EY

EX

EY

EC

LK

NC

NC

NC

DA

IN

AD

OU

T

BY

PA

SS

RC

VI

TX

LOS

S3

TX

LOS

S2

TX

LOS

S1

NC

NC

0VA

TX

OU

T

RX

IN

+5V

A

RS3

RS2

RS1

RS0

GP13

SEE NOTE 1

GP11

RTSn

EN85n

0VD2

PORin

XTLI

XTLO

XCLK

YCLK

+5VD1

24

100

99 98 97 96 95 94 93 92 91 90 89 88 87 86 85

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

D7

0VD2

0VD2

GP07

GP06

GP05

GP04

GP03

DCLKI(IRQ2n)73

SYNCIN2(G2XCLK)74

GP1675

GP1776

0VD277

CTSn78

TXD79

0VD280

ECLKIN1 25

SYNCIN1 26

NC 27

NC 28

NC 29

0VA 30

0VA

47

AG

D48

AO

UT

49

0VD

150

RS456

READn55

CSn54

WRITEn53

IRQn52

NC51

EY

EC

LKX

84

EY

ES

YN

C83

DC

LK82

0VD

281

UX-108U/178U/188UFO-375U

8 – 7

TEL/LIU PWB UNITIC1: VHiNJM2904D-1 (NJM2904D)

IC3: VHiR96XFC3CID (XFC3)

ST

RB

PO

L37

A23 1

A22 2

A21 3

A20 4

A19 5

A18 6

VSSO 7

A17 8

A16 9

A15 10

A14 11

A13 12

A12 13

VDDO 14

A11 15

A10 16

A9 17

A8 18

A7 19

A6 20

VSSO 21

A5 22

A4 23

A3 24

A2 25

A1 26

A0 27

VSSI 28

PCLK 29

POAT 30

VSSO108

GPIO20/ALTTONE107

106

105

104

SM3/GPO7103

VDDI102

START101

CLK1100

CLK1N99

CLK298

97

FCS1N/VIDCTL096

VSSI95

94

93

92

91

90

89

88

87

86

85

84

83

82

VDDO81

80

79

D0

144

D1

143

D2

142

D3

141

VD

DO

140

D4

139

138

137

136

135

134

133

132

131

130

DE

BU

GN

129

RD

N128

WR

N127

126

109

D6

D7

SY

SC

LK

VS

SO

RE

SE

TN

TS

TC

LK

SY

NC

DW

RND5

MIR

ON

VS

SI

OP

O7/G

PO

1538

OP

O6/G

PO

1439

OP

O5/G

PO

1340

VD

DO

41

OP

O4/G

PO

12 /S

ST

XD

142

OP

O3/G

PO

1143 44

VS

SO

45 46 47

VD

DI

48 49 50 51 52

VS

SI

53

VS

SO

72

LCD

CS

/GP

IO17

54 55

RE

GD

MA

124

VD

DI

123

122

121

120

119

118

117

116

115

114

RA

SN

113

CA

S0N

112

CA

S1N

111

110

125

MC

SN

RO

MC

SN

PM

3/GP

O3

VD

RA

M

WR

PR

OT

N

WA

ITN

CS

IN

TO

NE

CS

0N57

TE

ST

58

XIN

59

XO

UT

60

BA

TR

ST

N61

PW

RD

WN

N62

VB

AT

63

VS

SI

64

TH

AD

I65

–VR

EF

/CLR

EF

66

VIN

67

AD

XG

68

AD

GA

69

AD

GD

56

AD

VA

70

+V

RE

F71

PLAT 31

VDDI 32

STRB3 33

STRB2 34

STRB1 35

STRB0 36

78

77

76

75

GPIO18/IRQ9N74

GPIO19/RDY /SEROUT73

OP

O2/G

PO

10

OP

O1/G

PO

9

OP

O0/G

PO

8

OP

13/GP

IO24

OP

12/GP

IO23

/SS

CLK

I

OP

11/GP

IO22

/SS

TA

TI

OP

10/GP

IO21

/SS

RX

DI

LED

GT

L/GP

IO16

GPIO17/IRQ5N

GPIO16/IRQ8

GPIO15/CS5N

GPIO14/CS4N

GPIO13/CS3N

GPIO12/CS2N

GPIO11/BE /SERINP

GPIO10/SSSTAT2

GPIO9/FRDN

GPIO8/FWRN

GPIO7/SSRXD2

GPIO6/SSTXD2

VSSO

GPIO5/SSCLK2

GPIO4

GPIO3/SASCLK

GPIO2/SASRXD

GPIO1/SASTXD

GPIO0

FCS2N/VIDCTL1

SM2/GPO6

SM1/GPO5

SM0/GPO4

PM

2/GP

O2

PM

1/GP

O1

PM

0/GP

O0

IC3 VHIR96XFC3CID

1

2

3

4

8

7

6

5

–

+

OUTPUT 1

INVERTING INPUT 1

NON-INVERTING INPUT 1

VCC

VCC

OUTPUT 2

INVERTING INPUT 2

NON-INVERTING INPUT 2-

–

+

+

1 - 1

UX-108U/178U/188UFO-375U

CONTENTS

PARTS GUIDE

Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must bereplaced with the parts specifi to the product specification.

1 Cabinet, etc.

2 Upper cabinet

3 Document guide upper

4 Drive unit (Non cutter model)(UX-108)

5 Drive unit (Cutter model)(UX-178/188/FO-375)

6 Packing material & Accessories

7 Control PWB unit

8 TEL-Liu PWB unit

9 Power supply PWB unit

50 Hardware parts

Index

UX-108UX-178UX-188

MODEL FO-375Non Cutter model Cutter model

UX-108 UX-178/188

FO-375

UX-108U/178U/188UFO-375U

[1] Cabinet, etc.

– 1 –

57

57

12

4041

46

46

50B6

B6

B4

B1

B7

B4

B4

B5

B4

B4

B4

B4 B1

B1

B4

B4

B4

B4

B4

48

42

37

33

28

34

3132

3038

35

39

29

29

22

24

5536

2523

54

21

10

17

13

20

19

43

18

8

56

4551

52

53

47

44

44

49

9

610

258

2

7

11

141

54

3 3

26

27

B4

B4

15 DOCUMENTGUIDEUPPER

(NONCUTTER MODEL)

(CUTTER MODEL)

DRIVE UNIT(CUTTER MODEL)

(CUTTER MODEL)

59

60

UX-108U/178U/188UFO-375U

NO. PARTS CODEPRICERANK

NEWMARK

PARTRANK

DESCRIPTION

– 2 –

[1] Cabinet etc.1 LFRM-2184XHZZ AP N C Head frame2 MSPRC2949XHZZ AC N C Head spring A3 MSPRC2950XHZZ AC N C Pinch roller pressing spring4 NROLP2334XHZA AC N C Pinch roller5 NSFTZ2281XHZZ AD N C Pinch roller shaft6 PGIDP2497XHZZ AC N C Head support,left7 PGIDP2498XHZZ AC N C Head support,right8 PSHEZ3324XHZZ AD N C Head sheet9 QCNW-4748XHZZ AP N C Head cable

10 QCNW-4817XHZZ AE N C Head earth cable11 RHEDZ2054XHZZ BP N B Thermal head12 DCEKP370BXH01 BL N E Operation panel unit [108U/178U]

DCEKP370BXH05 BF N E Operation panel unit [188U]DCEKP370BHX04 BF N E Operation panel unit [375U]

13 LBNDJ2006XHZZ AA C Band(GT-100M)14 LSTPF2049XHZZ AD N C Stopper plate15 QCNW-4816XHZZ AL N C Panel cable17 CCNW-4745XH01 AL N C Speaker ass’y18 GCABB2298XHZA AT N D Lower cabinet [108U/178U]

GCABB2298XHZC AT N D Lower cabinet [188U]GCABB2298XHZB AT N D Lower cabinet [375U]

19 MLEVP2263XHZZ AC N C Paper sensor lever [178U/188U/375U]20 MSPRD2947XHZZ AC N C Paper sensor lever spring [178U/188U/375U]21 DCEKL366BXH01 BE N E TEL/Liu PWB unit22 GCASP2099XHZZ AN N C PWB case,top23 GCASP2100XHZZ AN N C PWB case,bottom24 QACCZ2012XHZZ AT N B AC cord ass’y

! 25 RDENT2116XHZZ BN N E Power supply PWB unit26 GDAI-2078XHZA AH N C Handset cover [108U/178U]

GDAI-2078XHZC AH N C Handset cover [188U]GDAI-2078XHZB AH N C Handset cover [375U]

27 MLEVP2261XHZZ AD N C Hook switch lever28 LFRM-2185XHZZ AH N C Scanner fram29 MSPRC2948XHZZ AC N C CIS spring30 NGERH2379XHZZ AC N C Idler gear,25Z31 NGERH2380XHZZ AC N C Reduction gear,17/36Z32 NGERH2392XHZZ AC N C Reduction gear,17/21Z33 NROLR2375XHZZ AL N C Feed roller34 NSFTZ2273XHZZ AF N C Feed roller shaft35 PGIDP2513XHZZ AH N C CIS support,left [108U]

PGIDP2499XHZZ AD N C CIS support,left [178U/188U/375U]36 PGIDP2514XHZZ AH N C CIS support,right [108U]

PGIDP2500XHZZ AD N C CIS support,right [178U/188U/375U]37 PGIDP2505XHZZ AF N C Document guide lower38 QCNW-4814XHZZ AG N C CIS cable [108U]

QCNW-4747XHZZ AH N C CIS cable [178U/188U/375U]39 RUNTZ2021SCZZ BF N B CIS unit [108U]

RUNTZ2020SCZZ BF N B CIS unit [178U/188U/375U]40 MLEVP2262XHZZ AD N C Paper sensor lever41 MSPRC2989XHZZ AC N C Paper sensor lever spring42 PGIDP2496XHZZ AD N C Paper support guide43 DCEKC587JXHZZ BV N E Control PWB unit(Within ROM) [108U]

DCEKC586JXHZZ BZ N E Control PWB unit(Within ROM) [178U/188U/375U]44 LBSHP2092XHZZ AC N C Platen bearing45 MARMP2019XHZZ AC N C Cutter arm [178U/188U/375U]46 MSPRC2945XHZZ AC N C Anti curl spring47 NGERH2382XHZZ AC N C Platen gear48 NROLP2332XHZZ AD C PO pinch roller49 NROLR2376XHZZ AX N C Platen roller50 NSFTZ2274XHZZ AK N C Anti curl shaft51 PCUT-2037SCZZ AT N C Cutter [178U/188U/375U]52 PGIDP2506XHZZ AE N C Cutter guide [178U/188U/375U]53 PGIDP2507XHZZ AF N C Cutter cover [178U/188U/375U]54 GLEGG2068XHZZ AC N C Rubber leg55 PSHEZ3325XHZZ AD N C Jack sheet56 PGIDP2503XHZZ AH N C Paper guide upper [108U]57 PSHEZ3362XHZZ AD N C Guide sheet58 MSPRC3005XHZZ AC N C Head spring B

! 59 RCORF2103XHZZ AF B Core! 60 RCORF2064XHZZ AF B Core

UX-108U/178U/188UFO-375U

– 3 –

[2] Upper cabinet

[3] Document guide upper

14

11

2

1

3

5

4

12

10

8

7

9

6

B2

B3

B3

13

3 2

75

6

4

915

10

16

1

14

13

12

1

11

8

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 4 –

[2] Upper cabinet1 GCABA2297XHZA AT N D Upper cabinet [108U/178U]

GCABA2297XHZC AT N D Upper cabinet [188U]GCABA2297XHZB AT N D Upper cabinet [375U]

2 JBTN-2216XHZA AF N C 12 key [108U/178U]JBTN-2216XHZC AF N C 12 key [188U]JBTN-2216XHZB AF N C 12 key [375U]

3 JBTN-2217XHZA AD N C Direct key [108U/178U]JBTN-2217XHZC AE N C Direct key [188U]JBTN-2217XHZB AE N C Direct key [375U]

4 JBTN-2218XHZZ AE N C Start key5 JBTN-2219XHZZ AD N C Stop key6 LPLTP2909XHZA AE N C Document tray [108U/178U]

LPLTP2909XHZC AE N C Document tray [188U]LPLTP2909XHZB AE N C Document tray [375U]

7 MSPRC2954XHZZ AC N C Hopper spring8 NGERP2318XHZZ AD C Pinion gear9 PGIDP2501XHZA AE N C Hopper guide,left [108U]

PGIDP2501XHZC AE N C Hopper guide,left [188U]PGIDP2501XHZB AE N C Hopper guide,left [375U]

10 PGIDP2502XHZA AE N C Hopper guide,right [108U]PGIDP2502XHZC AE N C Hopper guide,right [188U]PGIDP2502XHZB AE N C Hopper guide,right [375U]

11 HPNLH2383XHZB AK N D Decoration panel [108U]HPNLH2383XHZA AK N D Decoration panel [178U]HPNLH2383XHZD AK N D Decoration panel [188U]HPNLH2383XHZC AD N D Decoration panel [375U]

12 QCNW-4816XHZZ AL N C Panel cable13 DCEKP367BXH01 BH N E Operation panel PWB unit14 LBNDJ2006XHZZ AA C Band

(Unit)901 DCEKP370BXH01 BL N E Operation panel unit [108U/178U]

DCEKP370BXH05 BF N E Operation panel unit [188U]DCEKP370BXH04 BF N E Operation panel unit [375U]

[3] Document guide upper1 LBSHP2093XHZZ AC N C Bearing2 LPLTG2911XHZZ AE N C Separator rubber3 LPLTP2908XHZZ AE N C Separator plate4 MLEVP2264XHZZ AD N C Panel lock lever5 MLEVP2265XHZZ AD N C Document sensor lever6 MSPRD2953XHZZ AC N C Document sensor lever spring7 MSPRP2944XHZZ AC N C Paper feed spring8 MSPRT2951XHZZ AC N C Separate spring9 MSPRT2951XHZZ AC N C Panel lock lever spring

10 NGERH2383XHZZ AC N C Idler gear,2011 NGERH2402XHZZ AC N C CIS gear,29Z12 NROLR2372XHZZ AL N C CIS roller A ass’y13 NROLR2373XHZZ AL N C CIS roller B ass’y14 NROLR2374XHZZ AP N C Transfer roller15 PGIDP2504XHZZ AF N C Document guide upper16 PSHEZ3355XHZZ AD N C Rear sheet

UX-108U/178U/188UFO-375U

– 5 –

[4] Drive unit (Non cutter model) (UX-108)

[5] Drive unit (Cutter model) (UX-178/188/FO-375)

19

2

1

16

18

1213

1213

11

9

6

3

114

85

8

13

B4

19

2

17

18

1

16

18

1213

14

11 15 1213

138 7

1511

9

6

3

11

10

4

85

8

13

B4

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 6 –

[4] Drive unit(Non cutter model) (UX-108)1 LFRM-2187XHZZ AR N C Drive unit frame2 LPLTM2910XHZZ AE N C Motor heat sink3 MCAMP2024XHZZ AE N C Cam4 MLEVP2266XHZZ AD N C Planet gear lever A5 MLEVP2267XHZZ AD N C Planet gear lever B6 MLEVP2268XHZZ AD N C Change lever A8 MSPRC2955XHZZ AC N C Planet gear spring9 MSPRT2956XHZZ AC N C Change lever spring

11 NGERH2379XHZZ AC N C Idler gear 25Z12 NGERH2380XHZZ AC N C Reduction gear 17/36Z13 NGERH2387XHZZ AC N C Planet gear 17Z16 QCNW-4749XHZZ AD N C Cam switch cable18 QSW-F2224SCZZ AE B Detection switch19 RMOTZ2134XHZZ BA N B Motor

[5] Drive unit(Cutter model) (UX-178/188/FO-375)1 LFRM-2186XHZZ AH N C Drive unit frame2 LPLTM2910XHZZ AE N C Motor heat sink3 MCAMP2024XHZZ AE N C Cam4 MLEVP2266XHZZ AD N C Planet gear lever A5 MLEVP2267XHZZ AD N C Planet gear lever B6 MLEVP2268XHZZ AD N C Change lever A7 MLEVP2270XHZZ AD N C Planet gear lever C8 MSPRC2955XHZZ AC N C Planet gear spring9 MSPRT2956XHZZ AC N C Change lever spring

10 NGERH2356XHZZ AC N C Idler gear,20Z11 NGERH2379XHZZ AC N C Idler gear,25Z12 NGERH2380XHZZ AC N C Reduction gear,17/36Z13 NGERH2387XHZZ AC N C Planet gear,17Z14 NGERH2390XHZZ AC N C Cutter gear,44Z15 NGERH2391XHZZ AC N C Reduction gear,17/30Z16 QCNW-4749XHZZ AD N C Cam switch cable17 QCNW-4750XHZZ AD N C Cutter cam switch cable18 QSW-F2224SCZZ AE B Detection switch19 RMOTZ2134XHZZ BA N B Motor

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 7 –

[6] Packing material & Accessories

14

2

10

8

4

3

11

12

6

7

9

5 FAXPAPER

1 15

AC CORD

13

TAPE

[6] Packing material & Accessories1 TINSE3745XHZZ AL N D Operation manual [108U/177U/188U]

TINSE3808XHZZ AX N D Operation manual [375U]2 TLABH4237XHZZ AC N D Rapid key labels3 SPAKC194AXHZZ AQ N D Packing case [108U]

SPAKC163AXHZZ AQ N D Packing case [178U]SPAKC274AXHZZ AQ N D Packing case [188U]SPKAC273AXHZZ AQ N D Packing case [375U]

4 TLABM4321XHZZ AD N D Box label [108U]TLABM4322XHZZ AD N D Box label [178U]TLABM4437XHZZ AD N D Box label [188U]

5 DUNTK369BXHSG AV N E Handset [108U/178U]DUNTK369BXHBE BE N E Handset [188U]DUNTK369BXHOG AP N E Handset [375U]

6 QCNW-3975XHGY AG C Telephone line cord7 QCNW-3976XHAG AH C Handset cord [108U/178U]

QCNW-3976XHBE AT C Handset cord [188U]QCNW-3976XHOG AT C Handset cord [375U]

8 SPAKP3385SCZZ AG D Vinyl cover9 SPAKA160AXHZZ AF N D Pad

10 SPAKA161AXHZL AF N D Packing add.,left11 SPAKA162AXHZR AF N D Packing add.,right12 TCADZ2586XHZZ AD N D Pop card [108U]

TCADZ2585XHZZ AD N D Pop card [178U/188U]13 PCUSK2113XHZZ AG N C CIS pad14 TCADZ2593XHZZ AD N D Reference guide15 TCADZ2598XHZZ AD N D Registration card

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 8 –

[7] Control PWB unit1 UBATL2046SCZZ AK N B Battery(CR2032T34) [BAT1]2 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C1]3 VCEAGA1HW105M AB C Capacitor(50WV 1.0µF) [C2]4 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C3]5 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C4]6 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C5]7 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C6]8 VCEAGA1HW107M AA C Capacitor(50WV 100µF) [C7]9 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C8]

10 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C9]11 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C10]12 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C100]13 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C101]14 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C103]15 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C104]16 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C105]17 VCCCTV1HH150J AA C Capacitor(50WV 15PF) [C106]18 VCCCTV1HH180J AA C Capacitor(50WV 18PF) [C107]19 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C108]20 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C109]21 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C110]22 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C111]23 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C112]24 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C113]25 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C114]26 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C115]27 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C116]28 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C117]29 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C119]30 VCCSTV1HL391J AA C Capacitor(50WV 390PF) [C120]31 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C121]32 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C122]33 VCKYTV1HB221K AA C Capacitor(50WV 220PF) [C123]34 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C124]35 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C125]36 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C126]37 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C127]38 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C128]39 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C129]40 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C131]41 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C132]42 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C133]43 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C134]44 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C135]45 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C136]46 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C137]47 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C138]48 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C139][178U/188U/375U]49 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C140]50 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C141]51 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C142]52 VCKYTV1HB472K AA C Capacitor(50WV 0.0047µF) [C143]53 VCCSTV1HL102J AA C Capacitor(50WV 1000PF) [C144]54 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C145]55 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C146]56 VCKYTV1HB681K AA C Capacitor(50WV 680PF) [C147]57 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C148]58 VCKYTQ1HF104Z AA C Capacitor(50WV 0.1µF) [C149]59 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C150]60 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C151]61 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C152]62 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C153]63 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C154]64 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C155]65 VCKYTQ1HF104Z AA C Capacitor(50WV 0.1µF) [C156]66 VCKYTV1CF105Z AB C Capacitor(16WV 1.0µF) [C157]67 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C158]68 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C159]69 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C160]70 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C161]71 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C162]72 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C163]73 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C164]74 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C165]75 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C166]76 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C167]77 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C168]78 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C169]79 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C170]80 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C171]

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 9 –

[7] Control PWB unit81 QCNCM7014SC0G AB C Connector(7pin) [CNCIS]82 QCNCM2442SC0B AB C Connector(2pin) [CNCSW]83 QCNCM7014SC0B AD C Connector(2pin) [CNCUT1][178U/188U/375U]84 QCNCW2500SC1B AF C Connector(12pin) [CNLIUA]85 QCNCM7014SC0F AB C Connector(6pin) [CNMT]86 QCNCM7014SC1E AC C Connector(15pin) [CNPN]87 QCNCW2500SC1J AD N C Connector(10pin) [CNPW]88 QCNCM2401SC0B AA C Connector(2pin) [CNSP]89 QCNCM7014SC1F AD C Connector(16pin) [CNTH]90 VHERD22FB3/-1 AC B Diode(RD22FB3) [D1]92 VHD1SS355//-1 AB B Diode(1SS355) [D100]93 VHDRB705D//-1 AD B Diode(RB705D) [D101]

! 94 VHVICPS07//-1 AA B Varistor(ICP-S07) [FU100]95 VHIMC34119DR2 AH N B IC(MC34119DR2) [IC1]96 VHIR96XFC3CID BR N B IC(R96DFXL-CID)[Within IC2 and IC3 pair] [IC2]97 VHIR96XFC3CID BR N B IC(XFC3)[Within IC2 and IC3 pair) [IC3]98 VHIHCF4066M1T AF N B IC(HCF4066) [IC4]99 VHIW24257S7LL AP B IC(W24257S-70LLT) [IC5]

100 VHIHCF4053M1T AG N B IC(HCF4053B) [IC6]101 VHIULN2003AN/ AE B IC(ULN2003ANS) [IC7]102 QSOCZ2053XH32 AK C IC socket(32pin) [IC8]

VHI27010FWR0F BA B IC,EPROM(1MB) [IC8][108U]VHI27010FWS0F BA B IC,EPROM(1MB) [IC8][178U/188U/375U]

105 VHILM2902D/-1 AH N B IC(LM2902D) [IC9]106 VHINJM2904M-2 AG N B IC(NJM2904M) [IC10]107 VHIPST596CMT1 AF B IC(PST596CNR) [IC100]108 RCILZ2145XHZZ AF N C Coil(Z2145) [L102]109 RCILZ2145XHZZ AF N C Coil(Z2145) [L103]110 RCILZ2145XHZZ AF N C Coil(Z2145) [L104]111 RCILZ2145XHZZ AF N C Coil(Z2145) [L105]112 VHPITR9606/-1 AG N B Photo transistor(ITR9606) [PI1][178U/188U/375U]113 VS2SD1858Q2-1 AE N B Transistor(2SD1858) [Q1][178U/188U/375U]114 VS2SC2412KS-1 AB B Transistor(2SC2412-K) [Q101]115 VS2SA1037KS-1 AB B Transistor(2SA1037KS) [Q102]116 VSRNC1402//-1 AC B Transistor(RNC1402) [Q103][178U/188U/375U]117 VRS-RE3AA270J AC N C Resistor(1W 27Ω ±5%) [R1][178U/188U/375U]118 VRS-TS2AD221J AA C Resistor(1/10W 220Ω ±5%) [R100][178U/188U/375U]119 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R101]120 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R102]121 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R103]122 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R104]123 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R105][178U/188U/375U]124 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R106][178U/188U/375U]125 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R109]126 VRS-TS2AD121J AA C Resistor(1/10W 120Ω ±5%) [R110]127 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R111]128 VRSTS2AD4752F AA C Resistor(1/10W 47.5KΩ ±1%) [R112]129 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R113]130 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R114]131 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R115]132 VRS-TS2AD224J AA C Resistor(1/10W 220KΩ ±5%) [R116]133 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R119]134 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R125]135 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R126]136 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R127]137 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R128]138 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R129]139 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R130]140 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R131]141 VRS-TS2AD3R0J AA C Resistor(1/10W 3Ω ±5%) [R136]142 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R137][108U]143 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R138]144 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R139]145 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R140]146 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R141]147 VRS-TS2AD224J AA C Resistor(1/10W 220KΩ ±5%) [R142]148 VRS-TS2AD302J AA C Resistor(1/10W 3.0KΩ ±5%) [R143]149 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R145]150 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R146]151 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R149]152 VRS-TS2AD106J AA C Resistor(1/10W 10MΩ ±5%) [R155]153 RCILZ2145XHZZ AF N C Coil(Z2145) [R156]154 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R157]155 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R158]156 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R159]157 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R162]158 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R163]159 VRS-TS2AD202J AA C Resistor(1/10W 2KΩ ±5%) [R164]160 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R165]161 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R166]

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 10 –

[7] Control PWB unit162 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R168]163 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R169]164 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R170]165 RCILZ2139SCZZ AC C Coil(Z2139) [R171]166 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R172]167 RCILZ2145XHZZ AF N C Coil(Z2145) [R174]168 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R175]169 VRS-TS2AD302J AA C Resistor(1/10W 3.0KΩ ±5%) [R176]170 VRS-TS2AD623J AA C Resistor(1/10W 62KΩ ±5%) [R177]171 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R178]172 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R179]173 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R181]174 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R183]175 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R184]176 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R185]177 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R186]178 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R187]179 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R188][108U]

VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R188][178U/188U/375U]181 VRS-TS2AD152J AA C Resistor(1/10W 1.5KΩ ±5%) [R189]182 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R190]183 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R191]184 VRSTS2AD8662F AA C Resistor(1/10W 86.6KΩ ±1%) [R192]185 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R193]186 VRSTS2AD1742F AA C Resistor(1/10W 17.4KΩ ±1%) [R194]187 VRSTS2AD8662F AA C Resistor(1/10W 86.6KΩ ±1%) [R195]188 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R196][178U/188U/375U]189 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R200]190 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R201]191 VRS-TS2AD474J AA C Resistor(1/10W 470KΩ ±5%) [R202]192 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R204]193 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R205]194 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R206]195 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R207]196 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R209][178U/188U/375U]197 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R210][178U/188U/375U]198 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R211]199 VRS-TS2AD562J AA C Resistor(1/10W 5.6KΩ ±5%) [R212]200 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R213]201 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R214]202 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R215]203 VRS-TS2AD302J AA C Resistor(1/10W 3.0KΩ ±5%) [R216]204 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R217][178U/188U/375U]205 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R218]206 VRS-TS2AD152J AA C Resistor(1/10W 1.5KΩ ±5%) [R219]207 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R220]208 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R221]209 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R222]210 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R223]211 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R224]212 VRS-TS2AD133J AA C Resistor(1/10W 13KΩ ±5%) [R225]213 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R226]214 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R227][178U/188U/375U]215 VRS-TS2AD562J AA C Resistor(1/10W 5.6KΩ ±5%) [R228]216 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R229]217 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R230]218 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R231]219 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R232]220 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R233]221 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R234]222 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R235][108U]

VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [R235][178U/188U/375U]224 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R236]225 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R237]226 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R238][178U/188U/375U]227 VRS-TS2AD121J AA C Resistor(1/10W 120Ω ±5%) [R239]228 RMPTY8103SCJF AF C Block resistor(1/8W 10KΩ ±1%) [RA1]229 RMPTW4271SCJF AD C Block resistor(1/8W 270Ω ±1%) [RA2]230 RMPTW4271SCJF AD C Block resistor(1/8W 270Ω ±1%) [RA3]231 RMPTW4271SCJF AD C Block resistor(1/8W 270Ω ±1%) [RA4]232 RMPTW4271SCJF AD C Block resistor(1/8W 270Ω ±1%) [RA5]233 RMPTW4271SCJF AD C Block resistor(1/8W 270Ω ±1%) [RA6]234 RMPTW4471SCJF AD C Block resistor(1/8W 470Ω ±1%) [RA7]235 QSW-M2259XHZZ AF N B Door sensor [SW1]236 RCRSB2122SCZZ AH N B Crystal(24.00014MHz) [X1]237 RCRSB0297AFZZ AD B Crystal(32.768KHz) [X2]238 TLABP3078SCZZ AA D Shading label(for EP-ROM)

(Unit)901 DCEKC587JXHZZ BV N E Control PWB unit(Within ROM) [108U]

DCEKC586JXHZZ BZ N E Control PWB unit(Within ROM) [178U/188U/375U]

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 11 –

[8] TEL/Liu PWB unit1 VHVRA391PV6-1 AE B Varistor(RA391PV6) [AR1]2 QCNW-4753XHZZ AE N C Cable [ARG]3 VCKYPU1HB222K AA C Capacitor(50WV 2200PF) [C1]4 RC-FZ3024SCZZ AG C Capacitor(250WV 0.82µF) [C2]5 VCKYPU1HB222K AA C Capacitor(50WV 2200PF) [C3]6 VCKYPU1HB222K AA C Capacitor(50WV 2200PF) [C4]7 VCKYPU1HB103K AA C Capacitor(50WV 0.010µF) [C5]8 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C6]9 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C7]

10 VCQYNA1HM333K AA C Capacitor(50WV 0.033µF) [C8]11 VCKYPU1HB102K AA C Capacitor(50WV 1000PF) [C9]12 VCKYPU1HB102K AA C Capacitor(50WV 1000PF) [C10]13 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C11]14 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C12]15 VCEAGA1HW225M AA C Capacitor(50WV 2.2µF) [C13]16 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C14]17 VCKYPU1HB102K AA C Capacitor(50WV 1000PF) [C15]18 VCKYPU1HB102K AA C Capacitor(50WV 1000PF) [C16]19 VCKYPU1HB221K AB C Capacitor(50WV 220PF) [C17]20 VCKYPU1HB332K AA C Capacitor(50WV 3300PF) [C18]21 VCKYPU1HF223Z AA C Capacitor(50WV 0.022µF) [C19]22 RRLYD3221SCZZ AN B Relay [CML]23 QCNCM2548SC1B AH N C Connector(12pin) [CNLIU]24 VHDDSS133//-1 AA B Diode(1SS133) [D1]25 VHDDSS133//-1 AA B Diode(1SS133) [D2]26 VHDDSS133//-1 AA B Diode(1SS133) [D3]27 VHDDSS133//-1 AA B Diode(1SS133) [D4]28 VHINJM2904D-1 AG B IC(NJM2904D) [IC1]29 RFILN2024XHZZ AG C Coil(N2024) [L7]30 QJAKZ2069SCBB AG N C Jack [MJ1/2]31 QJAKZ2070SC0D AF N C Jack [MJTEL]32 VHPPC814X//-1 AE B Photo transistor(PC814X) [PC1]33 VHPTLP521-1BL AE B Photo coupler(TLP521) [PC2]34 VSDTC114ES/-1 AB B Transistor(DTC114ES) [Q1]35 VS2SC1815GR-1 AB B Transistor(2SC1815GR) [Q2]36 VSDTC114ES/-1 AB B Transistor(DTC114ES) [Q3]37 VRD-HT2EY151J AA C Resistor(1/4W 150Ω ±5%) [R2]38 VRD-HT2EY300J AA C Resistor(1/4W 30Ω ±5%) [R3]39 VRD-HT2EY910J AA C Resistor(1/4W 91Ω ±5%) [R4]40 VRD-HT2HY223J AA C Resistor(1/2W 22KΩ ±5%) [R5]41 VRD-HT2EY223J AA C Resistor(1/4W 22KΩ ±5%) [R6]42 VRD-HT2EY103J AA C Resistor(1/4W 10KΩ ±5%) [R9]43 VRD-HT2EY103J AA C Resistor(1/4W 10KΩ ±5%) [R10]44 VRD-HT2EY152J AA C Resistor(1/4W 1.5KΩ ±5%) [R11]45 VRD-HT2EY102J AA C Resistor(1/4W 1.0KΩ ±5%) [R12]46 VRD-HT2EY152J AA C Resistor(1/4W 1.5KΩ ±5%) [R13]47 VRD-HT2EY153J AA C Resistor(1/4W 15KΩ ±5%) [R14]48 VRD-HT2EY332J AA C Resistor(1/4W 3.3KΩ ±5%) [R15]49 VRD-HT2EY103J AA C Resistor(1/4W 10KΩ ±5%) [R16]50 VRD-HT2EY103J AA C Resistor(1/4W 10KΩ ±5%) [R17]51 VRD-HT2EY102J AA C Resistor(1/4W 1.0KΩ ±5%) [R18]52 VRD-HT2EY103J AA C Resistor(1/4W 10KΩ ±5%) [R19]53 VRD-HT2EY153J AA C Resistor(1/4W 15KΩ ±5%) [R20]54 VRD-HT2EY621J AA C Resistor(1/4W 620Ω ±5%) [R21]55 VRD-HT2EY332J AA C Resistor(1/4W 3.3KΩ ±5%) [R22]56 VRD-HT2EY102J AA C Resistor(1/4W 1.0KΩ ±5%) [R23]57 QSW-Z2263XHZZ AG N B Hook switch [SW1]58 RTRNZ2128XH01 AP B Transformer(Z2128) [T1]59 VHVERZV5D471/ AC B Varistor(ERZVA5D471) [VA1]60 VHVERZV5D471/ AC B Varistor(ERZVA5D471) [VA2]61 VHEHZ2C1///-1 AA B Zener diode(HZ2C1-TA) [ZD1]62 VHEHZ2C1///-1 AA B Zener diode(HZ2C1-TA) [ZD2]63 VHEHZ27-1//-1 AB B Zener diode(HZ27C-1TA) [ZD3]64 VHEHZ2C1///-1 AA B Zener diode(HZ2C1-TA) [ZD4]65 VHEHZ2C1///-1 AA B Zener diode(HZ2C1-TA) [ZD5]

(Unit)901 DCEKL366BXH01 BE N E TEL/Liu PWB unit

[9] Power supply PWB unit1 0CBUGZ1063ZZ/ AF N C Capacitor(CFJC22E104M-X) [C1]2 0CBUGZ1060ZZ/ AL C Capacitor(KMF200VB-220M 18x30) [C5]3 0CBUGFQ103DU/ AF N C Capacitor(ECQE4103KF) [C6]4 0CBUGCU102CB/ AD N C Capacitor(ECKZ3A102KBP) [C7]5 0CBUGFF103AR/ AC C Capacitor(AMZ-103K50) [C8]6 0CBUGFF683AR/ AD C Capacitor(AMZ-683K50) [C9]7 0CBUGFF102AR/ AB C Capacitor(AMZ-102K50) [C10]

UX-108U/178U/188UFO-375U


NEWMARK

PARTRANK

DESCRIPTION

– 12 –

[9] Power supply PWB unit8 0CBUGFF102AR/ AB C Capacitor(AMZ-102K50) [C11]9 0CBUGCZ472HN/ AF N C Capacitor(ECKMRS472MEY) [C12]

10 0CBUGCZ332HN/ AE N C Capacitor(ECKMRS332MEY) [C13]11 0CBUGFF102AR/ AB C Capacitor(AMZ-102K50) [C14]12 0CBUGAE681UG/ AH C Capacitor(UPJ1V681MHH1AA) [C15]13 0CBUGCZ222AD/ AC C Capacitor(DD08E222P500V) [C16]14 0CBUGAC471UM/ AF C Capacitor(UPJ1C471MPH6AA) [C18]15 0CBUGAF1R0HD/ AC C Capacitor(UVZ1H010MDH1AA) [C19]16 0CBPKZ0194ZZ/ AC C Connector(B 2P3-VH) [CN1]17 0CBPKZ1105ZZ/ AH N C Connector(10PL-FJ) [CN2]18 0CBUBC0215CZ/ AD N B Diode(RL1N4004) [D1]19 0CBUBC0215CZ/ AD N B Diode(RL1N4004) [D2]20 0CBUBC0215CZ/ AD N B Diode(RL1N4004) [D3]21 0CBUBC0215CZ/ AD N B Diode(RL1N4004) [D4]22 0CBUBC0169CZ/ AF N B Diode(ERA22-06) [D5]23 0CBUBA0003BZ/ AD N B Diode(IS2076A) [D6]24 0CBUBC0336AZ/ AL N B Diode(S3L20U-4004P15) [D7]25 0CBUBC0302AZ/ AE B Diode(SR140) [D8]26 0CBUBA0003BZ/ AD N B Diode(IS2076A) [D9]27 0CBPJCSX2501/ AH A Current fuse(23702.5 ME600) [F1]28 0CBPZZ0906ZZ/ AH N A Circuit protect chip(CCP2E100) [F3]29 0CBBFZ89209Z/ AC C Ferrite core(BL01RN1-A62) [FB1]30 0CBUCB0196AZ/ AR N B IC(BA178M05T) [IC1]31 0CBUKZ0776ZZ/ AK C Filter(ELF15N007A) [L1]32 0CBUDC0062AZ/ AF B Photo coupler(PS2501-1) [PC1]33 0CBUAG0166BZ/ AQ N B FET(FS10KM-10) [Q1]34 0CBUAC0027CZ/ AG B Transistor(2SC2655-Y) [Q2]35 0CBUAC0034EZ/ AE B Transistor(2SC1740S) [Q3]36 0CBUAC0264AZ/ AD N B Transistor(2SC1741AS QR) [Q4]37 0CBUEEB564CS/ AC N C Resistor(RD16S 564J) [R1]38 0CBUEFER18CH/ AD C Resistor(SPRX2-R18J) [R2]39 0CBUEEB822CS/ AC N C Resistor(RD16S 822J) [R3]40 0CBUEEB101CS/ AC N C Resistor(RD16S 101J) [R4]41 0CBUEEB184CS/ AC N C Resistor(RD16S 184J) [R5]42 0CBUEEB154CS/ AC N C Resistor(RD16S 154J) [R6]43 0CBUEFE823CG/ AC C Resistor(RSS2 823J) [R7]44 0CBUEEB681CB/ AC N C Resistor(RD50SS 681J) [R8]45 0CBUEEB681CS/ AC N C Resistor(RD16S 681J) [R9]46 0CBUEEB220CS/ AC N C Resistor(RD16S 220J) [R10]47 0CBUEEB681CS/ AC N C Resistor(RD16S 681J) [R11]48 0CBUEEB222CS/ AC N C Resistor(RD16S 222J) [R12]49 0CBUEEB271CS/ AC N C Resistor(RD16S 271J) [R13]50 0CBUEEB392CS/ AC N C Resistor(RD16S 392J) [R14]51 0CBUEEB122CS/ AC N C Resistor(RD16S 122J) [R15]52 0CBUEEB681CB/ AC N C Resistor(RD50SS 681J) [R16]53 0CBPHZ0184ZZ/ AR N B Relay(AJS3312) [RY1]54 0CB829655007/ BE B Transformer(PT-U53-KTT) [T1]55 0CBUDC0232ZZ/ AF N B Thermistor(KL07L8R2F) [TH1]56 0CBUEZ0528ZZ/ AD N B Varistor(ERZV07D241-CS) [V1]57 0CBUFBA471CB/ AD N B Variable resistor(EVN DJA A03 BQ2(471)) [VR1]58 0CBUBDAC3R9C/ AD B Zener diode(RD3.9ESAB2) [ZD2]59 0CBUBDAC6R2C/ AC B Zener diode(RD6.2ESAB2) [ZD3]60 0CBUBDAE300D/ AD B Zener diode(RD30FB3) [ZD4]61 0CBLRZ6446ZP/ AQ N C Heat sink(J7E36-5001AT)62 0CBLRZ6447ZP/ AQ N C Heat sink(J7E36-5002AT)

(Unit)! 901 RDENT2116XHZZ BN N E Power supply PWB unit

[50] Hardware partsB1 XBBSD30P06000 AA C Screw(3x6)B2 LX-BZ2138XHZZ AB C ScrewB3 XUBSD20P06000 AA C Screw(2x6)B4 XEBSD30P10000 AA C Screw(3x10)B5 LX-BZ2222AXZZ AC C ScrewB6 XEBSD30P12000 AA C Screw(3x12)B7 XBPSN40P06K00 AA C Screw(4x6)

No. NEWMARK

PARTRANK

PRICERANKPARTS CODE No. NEW

MARKPARTRANK

PRICERANKPARTS CODENo. NEW

MARKPARTRANK

PRICERANKPARTS CODE

UX-108U/178U/188UFO-375U

– 13 –

I n d e x

[C]CCNW-4745XH01 1-17 AL N C

[D]DCEKC586JXHZZ 1-43 BZ N E

″ 7-901 BZ N EDCEKC587JXHZZ 1-43 BV N E

″ 7-901 BV N EDCEKL366BXH01 1-21 BE N E

″ 8-901 BE N EDCEKP367BXH01 2-13 BH N EDCEKP370BHX04 1-12 BF N EDCEKP370BXH01 1-12 BL N E

″ 2-901 BL N EDCEKP370BXH04 2-901 BF N EDCEKP370BXH05 1-12 BF N E

″ 2-901 BF N EDUNTK369BXHBE 6-5 BE N EDUNTK369BXHOG 6-5 AP N EDUNTK369BXHSG 6-5 AV N E

[G]GCABA2297XHZA 2-1 AT N DGCABA2297XHZB 2-1 AT N DGCABA2297XHZC 2-1 AT N DGCABB2298XHZA 1-18 AT N DGCABB2298XHZB 1-18 AT N DGCABB2298XHZC 1-18 AT N DGCASP2099XHZZ 1-22 AN N CGCASP2100XHZZ 1-23 AN N CGDAI-2078XHZA 1-26 AH N CGDAI-2078XHZB 1-26 AH N CGDAI-2078XHZC 1-26 AH N CGLEGG2068XHZZ 1-54 AC N C

[H]HPNLH2383XHZA 2-11 AK N DHPNLH2383XHZB 2-11 AK N DHPNLH2383XHZC 2-11 AD N DHPNLH2383XHZD 2-11 AK N D

[J]JBTN-2216XHZA 2-2 AF N CJBTN-2216XHZB 2-2 AF N CJBTN-2216XHZC 2-2 AF N CJBTN-2217XHZA 2-3 AD N CJBTN-2217XHZB 2-3 AE N CJBTN-2217XHZC 2-3 AE N CJBTN-2218XHZZ 2-4 AE N CJBTN-2219XHZZ 2-5 AD N C

[L]LBNDJ2006XHZZ 1-13 AA C

″ 2-14 AA CLBSHP2092XHZZ 1-44 AC N CLBSHP2093XHZZ 3-1 AC N CLFRM-2184XHZZ 1-1 AP N CLFRM-2185XHZZ 1-28 AH N CLFRM-2186XHZZ 5-1 AH N CLFRM-2187XHZZ 4-1 AR N CLPLTG2911XHZZ 3-2 AE N CLPLTM2910XHZZ 4-2 AE N C

″ 5-2 AE N CLPLTP2908XHZZ 3-3 AE N CLPLTP2909XHZA 2-6 AE N CLPLTP2909XHZB 2-6 AE N CLPLTP2909XHZC 2-6 AE N CLSTPF2049XHZZ 1-14 AD N CLX-BZ2138XHZZ 50-B2 AB CLX-BZ2222AXZZ 50-B5 AC C

[M]MARMP2019XHZZ 1-45 AC N CMCAMP2024XHZZ 4-3 AE N C

″ 5-3 AE N CMLEVP2261XHZZ 1-27 AD N CMLEVP2262XHZZ 1-40 AD N CMLEVP2263XHZZ 1-19 AC N CMLEVP2264XHZZ 3-4 AD N CMLEVP2265XHZZ 3-5 AD N CMLEVP2266XHZZ 4-4 AD N C

″ 5-4 AD N CMLEVP2267XHZZ 4-5 AD N C

″ 5-5 AD N CMLEVP2268XHZZ 4-6 AD N C

″ 5-6 AD N C

MLEVP2270XHZZ 5-7 AD N CMSPRC2945XHZZ 1-46 AC N CMSPRC2948XHZZ 1-29 AC N CMSPRC2949XHZZ 1-2 AC N CMSPRC2950XHZZ 1-3 AC N CMSPRC2954XHZZ 2-7 AC N CMSPRC2955XHZZ 4-8 AC N C

″ 5-8 AC N CMSPRC2989XHZZ 1-41 AC N CMSPRC3005XHZZ 1-58 AC N CMSPRD2947XHZZ 1-20 AC N CMSPRD2953XHZZ 3-6 AC N CMSPRP2944XHZZ 3-7 AC N CMSPRT2951XHZZ 3-8 AC N C

″ 3-9 AC N CMSPRT2956XHZZ 4-9 AC N C

″ 5-9 AC N C[N]

NGERH2356XHZZ 5-10 AC N CNGERH2379XHZZ 1-30 AC N C

″ 4-11 AC N C″ 5-11 AC N C

NGERH2380XHZZ 1-31 AC N C″ 4-12 AC N C″ 5-12 AC N C

NGERH2382XHZZ 1-47 AC N CNGERH2383XHZZ 3-10 AC N CNGERH2387XHZZ 4-13 AC N C

″ 5-13 AC N CNGERH2390XHZZ 5-14 AC N CNGERH2391XHZZ 5-15 AC N CNGERH2392XHZZ 1-32 AC N CNGERH2402XHZZ 3-11 AC N CNGERP2318XHZZ 2-8 AD CNROLP2332XHZZ 1-48 AD CNROLP2334XHZA 1-4 AC N CNROLR2372XHZZ 3-12 AL N CNROLR2373XHZZ 3-13 AL N CNROLR2374XHZZ 3-14 AP N CNROLR2375XHZZ 1-33 AL N CNROLR2376XHZZ 1-49 AX N CNSFTZ2273XHZZ 1-34 AF N CNSFTZ2274XHZZ 1-50 AK N CNSFTZ2281XHZZ 1-5 AD N C

[P]PCUSK2113XHZZ 6-13 AG N CPCUT-2037SCZZ 1-51 AT N CPGIDP2496XHZZ 1-42 AD N CPGIDP2497XHZZ 1-6 AC N CPGIDP2498XHZZ 1-7 AC N CPGIDP2499XHZZ 1-35 AD N CPGIDP2500XHZZ 1-36 AD N CPGIDP2501XHZA 2-9 AE N CPGIDP2501XHZB 2-9 AE N CPGIDP2501XHZC 2-9 AE N CPGIDP2502XHZA 2-10 AE N CPGIDP2502XHZB 2-10 AE N CPGIDP2502XHZC 2-10 AE N CPGIDP2503XHZZ 1-56 AH N CPGIDP2504XHZZ 3-15 AF N CPGIDP2505XHZZ 1-37 AF N CPGIDP2506XHZZ 1-52 AE N CPGIDP2507XHZZ 1-53 AF N CPGIDP2513XHZZ 1-35 AH N CPGIDP2514XHZZ 1-36 AH N CPSHEZ3324XHZZ 1-8 AD N CPSHEZ3325XHZZ 1-55 AD N CPSHEZ3355XHZZ 3-16 AD N CPSHEZ3362XHZZ 1-57 AD N C

[Q]QACCZ2012XHZZ 1-24 AT N BQCNCM2401SC0B 7-88 AA CQCNCM2442SC0B 7-82 AB CQCNCM2548SC1B 8-23 AH N CQCNCM7014SC0B 7-83 AD CQCNCM7014SC0F 7-85 AB CQCNCM7014SC0G 7-81 AB CQCNCM7014SC1E 7-86 AC CQCNCM7014SC1F 7-89 AD CQCNCW2500SC1B 7-84 AF C

QCNCW2500SC1J 7-87 AD N CQCNW-3975XHGY 6-6 AG CQCNW-3976XHAG 6-7 AH CQCNW-3976XHBE 6-7 AT CQCNW-3976XHOG 6-7 AT CQCNW-4747XHZZ 1-38 AH N CQCNW-4748XHZZ 1-9 AP N CQCNW-4749XHZZ 4-16 AD N C

″ 5-16 AD N CQCNW-4750XHZZ 5-17 AD N CQCNW-4753XHZZ 8-2 AE N CQCNW-4814XHZZ 1-38 AG N CQCNW-4816XHZZ 1-15 AL N C

″ 2-12 AL N CQCNW-4817XHZZ 1-10 AE N CQJAKZ2069SCBB 8-30 AG N CQJAKZ2070SC0D 8-31 AF N CQSOCZ2053XH32 7-102 AK CQSW-F2224SCZZ 4-18 AE B

″ 5-18 AE BQSW-M2259XHZZ 7-235 AF N BQSW-Z2263XHZZ 8-57 AG N B

[R]RC-FZ3024SCZZ 8-4 AG CRCILZ2139SCZZ 7-165 AC CRCILZ2145XHZZ 7-108 AF N C

″ 7-109 AF N C″ 7-110 AF N C″ 7-111 AF N C″ 7-153 AF N C″ 7-167 AF N C

RCORF2064XHZZ 1-60 AF BRCORF2103XHZZ 1-59 AF BRCRSB0297AFZZ 7-237 AD BRCRSB2122SCZZ 7-236 AH N BRDENT2116XHZZ 1-25 BN N E

″ 9-901 BN N ERFILN2024XHZZ 8-29 AG CRHEDZ2054XHZZ 1-11 BP N BRMOTZ2134XHZZ 4-19 BA N B

″ 5-19 BA N BRMPTW4271SCJF 7-229 AD C

″ 7-230 AD C″ 7-231 AD C″ 7-232 AD C″ 7-233 AD C

RMPTW4471SCJF 7-234 AD CRMPTY8103SCJF 7-228 AF CRRLYD3221SCZZ 8-22 AN BRTRNZ2128XH01 8-58 AP BRUNTZ2020SCZZ 1-39 BF N BRUNTZ2021SCZZ 1-39 BF N B

[S]SPAKA160AXHZZ 6-9 AF N DSPAKA161AXHZL 6-10 AF N DSPAKA162AXHZR 6-11 AF N DSPAKC163AXHZZ 6-3 AQ N DSPAKC194AXHZZ 6-3 AQ N DSPAKC274AXHZZ 6-3 AQ N DSPAKP3385SCZZ 6-8 AG DSPKAC273AXHZZ 6-3 AQ N D

[T]TCADZ2585XHZZ 6-12 AD N DTCADZ2586XHZZ 6-12 AD N DTCADZ2593XHZZ 6-14 AD N DTCADZ2598XHZZ 6-15 AD N DTINSE3745XHZZ 6-1 AL N DTINSE3808XHZZ 6-1 AX N DTLABH4237XHZZ 6-2 AC N DTLABM4321XHZZ 6-4 AD N DTLABM4322XHZZ 6-4 AD N DTLABM4437XHZZ 6-4 AD N DTLABP3078SCZZ 7-238 AA D

[U]UBATL2046SCZZ 7-1 AK N B

[V]VCCCTV1HH150J 7-17 AA CVCCCTV1HH180J 7-18 AA CVCCCTV1HH220J 7-37 AA C

″ 7-38 AA C

No. NEWMARK

PARTRANK


MARKPARTRANK


MARKPARTRANK

PRICERANKPARTS CODE

UX-108U/178U/188UFO-375U

– 14 –

VCCCTV1HH220J 7-69 AA C″ 7-70 AA C″ 7-71 AA C″ 7-72 AA C″ 7-73 AA C″ 7-74 AA C″ 7-75 AA C

VCCSTV1HL102J 7-53 AA CVCCSTV1HL391J 7-30 AA CVCEAGA1EW476M 7-2 AA C

″ 7-4 AA C″ 7-10 AA C

VCEAGA1HW105M 7-3 AB CVCEAGA1HW106M 7-6 AA C

″ 7-7 AA C″ 7-9 AA C

VCEAGA1HW107M 7-8 AA CVCEAGA1HW225M 8-15 AA CVCEAGA1HW226M 7-11 AB C

″ 8-8 AB CVCEAGA1HW475M 7-5 AA C

″ 8-9 AA C″ 8-13 AA C″ 8-14 AA C″ 8-16 AA C

VCKYPU1HB102K 8-11 AA C″ 8-12 AA C″ 8-17 AA C″ 8-18 AA C

VCKYPU1HB103K 8-7 AA CVCKYPU1HB221K 8-19 AB CVCKYPU1HB222K 8-3 AA C

″ 8-5 AA C″ 8-6 AA C

VCKYPU1HB332K 8-20 AA CVCKYPU1HF223Z 8-21 AA CVCKYTQ1HF104Z 7-58 AA C

″ 7-65 AA CVCKYTV1CF105Z 7-12 AB C

″ 7-14 AB C″ 7-15 AB C″ 7-16 AB C″ 7-19 AB C″ 7-21 AB C″ 7-23 AB C″ 7-24 AB C″ 7-25 AB C″ 7-26 AB C″ 7-27 AB C″ 7-29 AB C″ 7-36 AB C″ 7-39 AB C″ 7-40 AB C″ 7-41 AB C″ 7-51 AB C″ 7-55 AB C″ 7-62 AB C″ 7-66 AB C

VCKYTV1EB104K 7-31 AA C″ 7-34 AA C″ 7-42 AA C″ 7-46 AA C″ 7-47 AA C″ 7-48 AA C″ 7-54 AA C″ 7-57 AA C″ 7-60 AA C

VCKYTV1EF104Z 7-20 AA C″ 7-32 AA C″ 7-35 AA C″ 7-43 AA C″ 7-45 AA C″ 7-49 AA C″ 7-59 AA C″ 7-61 AA C″ 7-63 AA C″ 7-67 AA C″ 7-68 AA C

VCKYTV1HB102K 7-13 AA C″ 7-50 AA C

VCKYTV1HB102K 7-64 AA C″ 7-76 AA C″ 7-77 AA C″ 7-78 AA C″ 7-79 AA C″ 7-80 AA C″ 7-222 AA C

VCKYTV1HB103K 7-28 AB C″ 7-44 AB C

VCKYTV1HB221K 7-33 AA CVCKYTV1HB222K 7-22 AA CVCKYTV1HB472K 7-52 AA CVCKYTV1HB681K 7-56 AA CVCQYNA1HM333K 8-10 AA CVHDDSS133//-1 8-24 AA B

″ 8-25 AA B″ 8-26 AA B″ 8-27 AA B

VHDRB705D//-1 7-93 AD BVHD1SS355//-1 7-92 AB BVHEHZ2C1///-1 8-61 AA B

″ 8-62 AA B″ 8-64 AA B″ 8-65 AA B

VHEHZ27-1//-1 8-63 AB BVHERD22FB3/-1 7-90 AC BVHIHCF4053M1T 7-100 AG N BVHIHCF4066M1T 7-98 AF N BVHILM2902D/-1 7-105 AH N BVHIMC34119DR2 7-95 AH N BVHINJM2904D-1 8-28 AG BVHINJM2904M-2 7-106 AG N BVHIPST596CMT1 7-107 AF BVHIR96XFC3CID 7-96 BR N B

″ 7-97 BR N BVHIULN2003AN/ 7-101 AE BVHIW24257S7LL 7-99 AP BVHI27010FWR0F 7-102 BA BVHI27010FWS0F 7-102 BA BVHPITR9606/-1 7-112 AG N BVHPPC814X//-1 8-32 AE BVHPTLP521-1BL 8-33 AE BVHVERZV5D471/ 8-59 AC B

″ 8-60 AC BVHVICPS07//-1 7-94 AA BVHVRA391PV6-1 8-1 AE BVRD-HT2EY102J 8-45 AA C

″ 8-51 AA C″ 8-56 AA C

VRD-HT2EY103J 8-42 AA C″ 8-43 AA C″ 8-49 AA C″ 8-50 AA C″ 8-52 AA C

VRD-HT2EY151J 8-37 AA CVRD-HT2EY152J 8-44 AA C

″ 8-46 AA CVRD-HT2EY153J 8-47 AA C

″ 8-53 AA CVRD-HT2EY223J 8-41 AA CVRD-HT2EY300J 8-38 AA CVRD-HT2EY332J 8-48 AA C

″ 8-55 AA CVRD-HT2EY621J 8-54 AA CVRD-HT2EY910J 8-39 AA CVRD-HT2HY223J 8-40 AA CVRS-RE3AA270J 7-117 AC N CVRS-TS2AD000J 7-130 AA C

″ 7-131 AA C″ 7-133 AA C″ 7-168 AA C″ 7-179 AA C″ 7-208 AA C″ 7-214 AA C″ 7-222 AA C

VRS-TS2AD102J 7-119 AA C″ 7-172 AA C″ 7-173 AA C″ 7-174 AA C

VRS-TS2AD103J 7-120 AA C

VRS-TS2AD103J 7-121 AA C″ 7-122 AA C″ 7-134 AA C″ 7-138 AA C″ 7-140 AA C″ 7-142 AA C″ 7-144 AA C″ 7-146 AA C″ 7-151 AA C″ 7-161 AA C″ 7-183 AA C″ 7-205 AA C″ 7-207 AA C″ 7-211 AA C″ 7-226 AA C

VRS-TS2AD104J 7-135 AA C″ 7-145 AA C

VRS-TS2AD106J 7-152 AA CVRS-TS2AD121J 7-126 AA C

″ 7-227 AA CVRS-TS2AD133J 7-212 AA CVRS-TS2AD152J 7-181 AA C

″ 7-206 AA CVRS-TS2AD201J 7-127 AG C

″ 7-197 AG C″ 7-224 AG C


″ 7-185 AA C″ 7-190 AA C


″ 7-192 AA CVRS-TS2AD224J 7-132 AA C

″ 7-147 AA CVRS-TS2AD271J 7-129 AA C

″ 7-162 AA C″ 7-175 AA C″ 7-176 AA C″ 7-201 AA C″ 7-225 AA C

VRS-TS2AD3R0J 7-141 AA CVRS-TS2AD302J 7-148 AA C

″ 7-169 AA C″ 7-203 AA C

VRS-TS2AD303J 7-124 AA C″ 7-160 AA C″ 7-179 AA C″ 7-202 AA C″ 7-204 AA C″ 7-219 AA C

VRS-TS2AD332J 7-139 AA C″ 7-171 AA C″ 7-195 AA C″ 7-213 AA C

VRS-TS2AD333J 7-196 AA C″ 7-198 AA C″ 7-200 AA C

VRS-TS2AD471J 7-123 AA C″ 7-125 AA C″ 7-136 AA C″ 7-137 AA C″ 7-149 AA C″ 7-154 AA C″ 7-155 AA C″ 7-156 AA C″ 7-157 AA C″ 7-163 AA C″ 7-164 AA C″ 7-166 AA C″ 7-177 AA C″ 7-178 AA C″ 7-188 AA C″ 7-189 AA C″ 7-193 AA C″ 7-194 AA C″ 7-216 AA C″ 7-217 AA C″ 7-218 AA C″ 7-220 AA C

UX-108U/178U/188UFO-375U

– 15 –


″ 7-209 AA C″ 7-210 AA C

VRS-TS2AD474J 7-191 AA CVRS-TS2AD512J 7-182 AA CVRS-TS2AD562J 7-199 AA C

″ 7-215 AA CVRS-TS2AD623J 7-170 AA CVRSTS2AD1742F 7-186 AA CVRSTS2AD4752F 7-128 AA CVRSTS2AD8662F 7-184 AA C

″ 7-187 AA CVSDTC114ES/-1 8-34 AB B

″ 8-36 AB BVSRNC1402//-1 7-116 AC BVS2SA1037KS-1 7-115 AB BVS2SC1815GR-1 8-35 AB BVS2SC2412KS-1 7-114 AB BVS2SD1858Q2-1 7-113 AE N B

[X]XBBSD30P06000 50-B1 AA CXBPSN40P06K00 50-B7 AA CXEBSD30P10000 50-B4 AA CXEBSD30P12000 50-B6 AA CXUBSD20P06000 50-B3 AA C

[0]0CBBFZ89209Z/ 9-29 AC C0CBLRZ6446ZP/ 9-61 AQ N C0CBLRZ6447ZP/ 9-62 AQ N C

No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.

SHARP CORPORATIONCommunication Systems GroupQuality & Reliability Control CenterHigashihiroshima, Hiroshima 739-01, Japan

Printed in USA

9802-1892NS•IS•T

COPYRIGHT © 1998 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No. NEWMARK

PARTRANK


MARKPARTRANK

PRICERANKPARTS CODENo. NEW

MARKPARTRANK

PRICERANKPARTS CODE

0CBPHZ0184ZZ/ 9-53 AR N B0CBPJCSX2501/ 9-27 AH A0CBPKZ0194ZZ/ 9-16 AC C0CBPKZ1105ZZ/ 9-17 AH N C0CBPZZ0906ZZ/ 9-28 AH N A0CBUAC0027CZ/ 9-34 AG B0CBUAC0034EZ/ 9-35 AE B0CBUAC0264AZ/ 9-36 AD N B0CBUAG0166BZ/ 9-33 AQ N B0CBUBA0003BZ/ 9-23 AD N B

″ 9-26 AD N B0CBUBC0169CZ/ 9-22 AF N B0CBUBC0215CZ/ 9-18 AD N B

″ 9-19 AD N B″ 9-20 AD N B″ 9-21 AD N B

0CBUBC0302AZ/ 9-25 AE B0CBUBC0336AZ/ 9-24 AL N B0CBUBDAC3R9C/ 9-58 AD B0CBUBDAC6R2C/ 9-59 AC B0CBUBDAE300D/ 9-60 AD B0CBUCB0196AZ/ 9-30 AR N B0CBUDC0062AZ/ 9-32 AF B0CBUDC0232ZZ/ 9-55 AF N B0CBUEEB101CS/ 9-40 AC N C0CBUEEB122CS/ 9-51 AC N C0CBUEEB154CS/ 9-42 AC N C0CBUEEB184CS/ 9-41 AC N C0CBUEEB220CS/ 9-46 AC N C0CBUEEB222CS/ 9-48 AC N C

0CBUEEB271CS/ 9-49 AC N C0CBUEEB392CS/ 9-50 AC N C0CBUEEB564CS/ 9-37 AC N C0CBUEEB681CB/ 9-44 AC N C

″ 9-52 AC N C0CBUEEB681CS/ 9-45 AC N C

″ 9-47 AC N C0CBUEEB822CS/ 9-39 AC N C0CBUEFER18CH/ 9-38 AD C0CBUEFE823CG/ 9-43 AC C0CBUEZ0528ZZ/ 9-56 AD N B0CBUFBA471CB/ 9-57 AD N B0CBUGAC471UM/ 9-14 AF C0CBUGAE681UG/ 9-12 AH C0CBUGAF1R0HD/ 9-15 AC C0CBUGCU102CB/ 9-4 AD N C0CBUGCZ222AD/ 9-13 AC C0CBUGCZ332HN/ 9-10 AE N C0CBUGCZ472HN/ 9-9 AF N C0CBUGFF102AR/ 9-7 AB C0CBUGFF102AR/ 9-8 AB C

″ 9-11 AB C0CBUGFF103AR/ 9-5 AC C0CBUGFF683AR/ 9-6 AD C0CBUGFQ103DU/ 9-3 AF N C0CBUGZ1060ZZ/ 9-2 AL C0CBUGZ1063ZZ/ 9-1 AF N C0CBUKZ0776ZZ/ 9-31 AK C0CB829655007/ 9-54 BE B