OPERATOR'S MANUAL GRINDER-MIXER 355 =^^|VsEW HOLLAtsD
OPERATOR'SMANUALGRINDER-MIXER355
=^^|VsEW HOLLAtsD
A
CONTENTSADJUSTMENTS
Loading Auger Governor (optional) 17Relief Lid 17Loading Auger Speed 17Loading Auger Drive Belt 17Adjustable Mixing Tube 13Loading Auger Brake 18Unloading Auger Brake 18Gear Box and Transfer Auger Drive Chains 18Shear Bolt 18
Hammermill Drive Belt 19
Loading Auger Primary Drive Chain 19
Replacing or Turning Hammermill Hammers 20Loading Auger Clutch 21
Unloading Auger Clutch 21
LUBRICATION 12-16
MAINTENANCE 21-22
OPERATION 4-n
OPTIONAL EQUIPMENT 25
SAFETY 3
SERVICE ADJUSTMENT CHART 23
SPECIFICATIONS - 28
BE CAREFULMOST FARM IMPLEMENT ACCIDENTS CAN BE AVOIDED BY THE OBSERVANCE OF A FEWSIMPLE SAFETY PRECAUTIONS.
1
.
DON'T CLEAN, LUBRICATE, OR MAKE ANY ADJUSTMENTS ON THE GRINDER-MIXER WHILEIT IS IN MOTION.
2. DON'T START THE GRINDER-MIXER UNTIL YOU KNOW THAT EVERYONE IS CLEAR OF THEMACHINE AND HAVE MADE SURE THAT NO TOOLS ARE LYING ON THE MACHINE.
3. DON'T WORK AROUND THE UNIT IN LOOSE CLOTHING THAT MIGHT CATCH IN ANY OFTHE MOVING PARTS.
4. DON'T ATTEMPT TO PULL MATERIAL FROM ANY PART OF THE GRINDER-MIXER WHILE IT IS
IN OPERATION.
6.
7.
MAKE SURE ALL THE TRACTOR AND IMPLEMENT P.T.O.
FUNCTIONING PROPERLY.SHIELDS ARE IN PLACE AND
KEEP HANDS CLEAR OF AUGERS WHILE MACHINE IS IN OPERATION.
MAKE SURE THE HAMMERMILL IS COMPLETELY STOPPED BEFORE OPENING THE COVER.
8. ALWAYS REPLACE SHIELDS AFTER MAKING REPAIRS, ADJUSTMENTS OR AFTER LUBRICAT-
ING. SHIELDS ARE FOR YOUR PROTECTION; KEEP THEM IN PLACE!
ABE CAREFUL! THIS SYMBOL IS USED THROUGHOUT THIS BOOKWHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKETIME TO BE CAREFUL!
i
OPERATIONGENERAL INFORMATION
IN THE FOLLOWING INSTRUCTIONS "LEFT"AND "RIGHT" ARE DETERMINED FROM APOSITION FACING THE DIRECTION OF TRAVEL
The Model 355 grinder-mixer is intended to
be basically a grain processing grinder-mixer.However, roughage can be blended with grainin reasonable quantities.
TRACTOR HITCH
The hitch of the Grinder-Mixer is designedfor standard tractor hitch. Adjust the drawbarso that it is 13 to 17 inches above the ground.EXTEND OR SHORTEN IT SO THAT THE HORI-ZONTAL DISTANCE FROM THE END OF THETRACTOR POWER TAKE OFF SHAFT TO THECENTER OF THE HITCH PIN HOLE IS 14 INCHES,AS SHOWN IN FIGURE 1. Use an adapter plate,
if necessary, to secure the proper distance. ANIMPROPERLY LOCATED HITCH POINT MAYCAUSE DAMAGE TO THE UNIVERSAL JOINTSOF THE POWER TAKE OFF.
Secure the drawbar so that the hitch pin holeis directly below the power drive line.
14 FOR 540 R.PM.
ATTACHING TO THE TRACTOR
1. Fasten the Grinder-Mixer hitch to thedrawbar with A HITCH PIN THAT CAN-NOT BOUNCE OUT.
2. Remove the weight fronn the jack, swingit to its horizontal position, and lock it to
provide a maximum ground clearance.
3. Depress the spring loaded pin on theP.T.O. yoke and slide it on the tractor
P.T.O. shaft. Be sure the pin falls in thegroove of the P.T.O. shaft.
HAMMERMILL DRIVE
The hammermill drive is engaged or disen-
gaged as shown in Figure 2 by moving thepin in or out of the drive assembly.
IMPORTANT:
Do not off-set tractor draw bar to align P.T.O.
assembly. Keep draw bar directly beneath the
tractor P.T.O. If tractor draw bar is off-set, the
P.T.O. can bottom and cause damage.
OPERATING SPEED
During the grinding and mixing operation
maintain the standard 540 RPM on the P.T.O.
Use slow P.T.O. speed to stop the P.T.O. whenengaging the unloading auger clutch.
FIGURE 2
LOADING AUGER DRIVE (Mechanical)
During operation the loading auger can beengaged or disengaged by the clutch lever
shown in Figure 3.
The loading auger is held in transport posi-
tion with the transport latch shown in Figure 3.
LOADING AUGER DRIVE (Hydraulic)
The speed of the loading auger can be con-
trolled with the loading auger speed control
valve. The loading auger can be stopped bymoving the lever as indicated in Figure 3A.
IMPORTANT: The loading and unloading au-
gers are driven with orbit nnotors. If the augers
become jammed with material or foreign ob-
jects, the orbit motor will stall. When this oc-
curs, oil no longer is pumped through the entire
hydraulic system but is forced across the pres-
sure relief valve that is factory set at 2000p.s.i. relief pressure.
FIGURE 3
The operator must disengage the power sup-ply immediately after these conditions. The ob-struction or overload must be removed beforeoperation is continued.
Permanent damage from excessive heat couldoccur if both pump and motor were to continueoperation under these conditions.
BE CAREFUL AKEEP HANDS CLEAR OF AUGERS
WHILE MACHINE IS IN OPERATION.
FIGURE 3 A
I
OPERATION
1. Attach grinder-mixer to tractor as outlined
in "Attaching to Tractor."
2. Engage hannmermill drive pin as shown in
Figure 2.
3. Disengage the unloading auger drive. SeeFigure 10.
4. Install the desired size screen. See Figure14.
5. To prepare for operation: Unlatch the trans-
port latch. Raise the loading auger with the
winch. Position the loading auger in the
desired location and lock into position withthe loading auger brake shown in Figure 4.
6. Start the unit and set the hammernnill gate
to control the amount of material goinginto the mill. See Figure 5.
IMPORTANT: FOR BEST MIXING RESULTS,BE SURE TO ADD LIGHTWEIGHT OR BULKYMATERIALS LAST. ALWAYS ADD HIGHMOISTURE CORN OR GRAIN LAST.
7. Feed material into the mill by engagingthe loading auger drive with clutch lever
shown in Figure 4.
8. The amount of material being fed by the
auger can be regulated by changing the
speed of the loading auger. See loading
auger speed for this adjustment. IMPOR-
OPTIONAL SfV
GRAIN COVL - xEMOVE FOR EAR CORN
IFIGURE 6
FIGURE 5
RAISE OR LOWER WITH WINCH
LOADING AUGERCLUTCH
FIGURE 4
TANT: SMALL GRAIN COVER MUST BEREMOVED WHEN HANDLING EAR CORN.Cover shown in Figure 6.
9. Observe the mixing of the feed and the
amount in the tank through the tank win-
dows. NOTE: The tank is filled to capacity
when the material covers the top windowand suddenly drops away.
10. When adding concentrates or special feeds
through the concentrate hopper at the rear
of the unit the grinder mixer should beoperating at 540 R.P.M. See Figure 7. Donot add material through the concentrate
hopper and hammermill at the same time.
n. When the tank is full or the feed mixtureis completely mixed, stop the unit and dis-
engage the hammermill drive.
NOTE: The unloading auger clutch may beengaged or disengaged while the unit is
operating if necessary, but should be doneat slow tractor R.P.M.
12. To unload, release the auger transport latch
and raise the unloading auger to clear the
transport support. Release the outer augerlatch and swing the auger end to couple
with the auger base section. Augers mustalign and engage properly before locking
over center clamp. Lock the auger sections
together and position auger to desired po-
sition. IMPORTANT: Lock the unloading au-
ger brake when unloading. Damage can
occur to the bearing and yoke if the brake
is not locked when operating the unload-
13.
FIGURE 7
ing auger. Engage the unloading auger
drive. See Figure 10.
Start the unit and raise the gate in the tank
unloading auger by turning the crank. Tounload all the material in the tank, close the
unloading gate to about Va open.
10' UNLOADINGAUGER BRACES
AUGER EXTENSION SUPPORTS
10* EXTENSIONSHOWN
FIGURE 8
AKEEP [HILDREH HlUnV
HI HLL TimES
FIGURE 9
PT.O. CARRIERUNLOADING AUGER CLUTCH LEVER
AFIGURE 10
BE CAREFUL! THIS SYMBOL IS USED THROUGHOUT THIS BOOKWHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKETIME TO BE CAREFUL!
8
RELIEF LID
FIGURE TO A
14. After the tank is emptied, return the un-
loading auger to the transport position as
shown in Figure 12. Secure with the trans-
port latch.
15, Place the jack in the down position and
the PTO shaft on the carrier when unhitch-
ing. See Figure 3.
DRAIN COVERSDrain covers are provided at five locations,
see Figure 11 A. The covers are located at the
bottom of the loading auger. Figure 12, tank
unloading auger and unloading auger. Figure
10, and at both ends of the transfer auger. Fig-
ure 32A. Be sure covers are closed when oper-
ating grinder-mixer.
FIGURE 11 A
GRINDING HAYTo grind hay with the unit, place the load-
ing auger in transport position, and disengage
the drive. Open the hammermill gate to a wideposition. For best results feed slices 3" to 5"
thick into hammermill. For fine grasses and
slough hay feed thinner slices.
PT.O. CARRIER
FIGURE 12
GRINDING WITHOUT MIXING
If it is desirable to grind but not mix the feedmaterial, engage the unloading auger drive,
open the tank unloading auger gate and start
grinding. The material will be conveyed to the
bottom of the tank and out through the unload-ing augers without mixing.
When operating in this manner the bevel
gears will need frequent lubrication,
MIXING HIGH MOISTURE, LIGHT WEIGHT, ORBULKY MATERIAL
For best mixing results, always add light-
weight or bulky materials last. Always addhigh moisture corn or grain last.
Excessive amounts of wet material, light
weight material, or bulky material, will causebridging in the mixing tank. Therefore, mix-ing will not be adequate and unloading timewill be very slow.
UNLOADING AUGER DISCHARGE HEIGHTThe lower limit discharge height of the un-
loading auger is controlled by the length of
cable on the winch. The winch contains the
maximum amount of cable that can be usedas it is shipped from the factory. If the cableis lengthened, the unloading auger gears maylock and cause breakage of the unloading auger
clutch or gear box. If it is desirable to lower thedischarge height of the unloading auger, theoptional flexible down spout attachment shouldbe added.
ABE CAREFUL
MAKE SURE THE HAMMERMILL IS
COMPLETELY STOPPED BEFORE
OPENING THE COVER TOCHANGE THE SCREENS
CHANGING HAMMERMILL SCREENS(Be sure Tractor Engine has stopped)
To change the hammermill screen:
1. Open the cover by loosening the over cen-ter clamp.
2. Insert the hook in the screen and pull upand outward as shown in Figure 14.
3. Install the screen by dropping in place andclosing the door.
TO
FIGURE 14
4. Extra screens may be carried in the screenrack and secured as shown in Figure 14.
NOTE: Clean rust preventive fronn screens
before installing them.
TRANSPORTING THE GRINDER-MIXER
When moving the unit with material in the
tank, the mixing auger should be run at a slowspeed.
If the Grinder-Mixer is equipped with a load-
ing auger , the right side of the hopper can befolded.
SCREEN SIZES
The following suggested screen sizes maybe used as a guide for grinding different typesof feed.
1. Dairy cattle:
Ear corn- 1/4-1/2"
Small grains -3/16-5/16"
2. Hogs and poultry:
Shelled corn- 1/8-1/4"
Small grains -3/32-1/4"
3. Beef Cattle:
Ear corn- 1/4-1"
Shelled corn -3/16-1/2"Small grains -3/16-1/2"
NOTE: Do not attempt to grind ear corn
through a screen smaller than %" or hayand straw through a screen larger than %"for satisfactory performance. Grinding high
moisture material could cause grinding andmixing problems.
Always attach the PTO to the tractor or at-
tach it to the PTO carrier as shown in Figure 1 2.
The reflective tape and SMV emblem on therear of the machine should be cleaned regular-
ly when transporting the unit on a highway.
A BE CAREFUL! THIS SYMBOL IS USED THROUGHOUT THIS BOOKWHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKETIME TO BE CAREFUL!
11
A BE CAREFULMOST FARM IMPLEMENT ACCIDENTS CAN BE AVOIDED BY THE OBSERVANCE OF A FEWSIMPLE SAFETY PRECAUTIONS.
1
.
DON'T CLEAN, LUBRICATE, OR MAKE ANY ADJUSTMENTS ON THE GRINDER-MIXER WHILEIT IS IN MOTION.
2. DON'T START THE GRINDER-MIXER UNTIL YOU KNOW THAT EVERYONE IS CLEAR OF THE
MACHINE AND HAVE MADE SURE THAT NO TOOLS ARE LYING ON THE MACHINE.
3. DON'T WORK AROUND THE UNIT IN LOOSE CLOTHING THAT MIGHT CATCH IN ANY OFTHE MOVING PARTS.
4. DON'T ATTEMPT TO PULL MATERIAL FROM ANY PART OF THE GRINDER-MIXER WHILE IT IS
IN OPERATION.
5. MAKE SURE ALL THE TRACTOR AND IMPLEMENT P.T.O. SHIELDS ARE IN PLACE ANDFUNCTIONING PROPERLY.
6. KEEP HANDS CLEAR OF AUGERS WHILE MACHINE IS IN OPERATION.
7. MAKE SURE THE HAMMERMILL IS COMPLETELY STOPPED BEFORE OPENING THE COVER.
8. ALWAYS REPLACE SHIELDS AFTER MAKING REPAIRS, ADJUSTMENTS OR AFTER LUBRICAT-
ING. SHIELDS ARE FOR YOUR PROTECTION; KEEP THEM IN PLACE!
LUBRICATIONUnder normal conditions, the Sperry New
Holland Grinder-Mixer should be greased EV-
ERY EIGHT HOURS OF OPERATION, OR ONCEA MONTH, whichever comes first. It should belubricated more often if operating under ex-
tremely heavy loads or extremely adverse con-
ditions.
The following is a list of points that require
lubrication, with a reference number that iden-
tifies each location on the corresponding de-
tail pictures. A single asterisk in front of the
reference number indicates lube point for me-
chanical drive only. A double asterisk applies to
hydraulic drive only. All other reference num-bers apply to either unit. All points except those
with special notations should be lubricated with
a good grade of grease until grease is forced
out around the bearings. The excess grease
should then be wiped off. Dirt should be wipedfrom the fittings before applying grease.
BE CAREFULGREASE AND OIL THIS MACHINE ONLYWHEN THE P.T.O. IS DISENGAGED ANDTRACTOR ENGINE IS NOT RUNNING
A
FIGURE 17
12
Location
1, Figure 17
2, Figure 17
3, Figure 17
A, Figure 17
4A, Figure 19
5, Figure 18
6, Figure 18
7, Figure 18A
8, Figure ISA
Quantity Description
Front Universal joint
Telescoping P.T.O.
Rear universal joint
Jack
Drive sheave bearings
Front drive shaft bearing
Rear drive shaft bearing
Front hammermill shaft
Rear hammermill shaft
J
9, Figure 18B
*9, Figure 19A
10, Figure 18B
Frequency of Lubrication
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
Repack every three years.
Every 8 hours — Grease spar-ingly until grease just comesthrough seal.
Grease sparingly every 100hours or once per year v\/hich-
ever comes first.
FIGURE T8
I^^W^ , OPTIONa
Grease clutch in both positions,
engaged and disengaged.
FIGURE 19A
FIGURE 20A
FIGURE 20
*12, Figures 23 & 20A
*13, Figures 23 & 20A
*14, Figure 10
M5, Figure 23
16, Figure 23
*17, Figure 20
*18, Figure 20
*19, Figure 20
20, Figure 21
Unloading auger pivot bearing Every 8 hours
Idler gear
Unloading auger bearing
Tank discharge auger bearing,
upper
Transfer auger bearing
Rear loading auger bearing
Front loading auger bearing
Rear Universal joint
Vertical auger upper bearing
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
Every 8 hours
14
«^
*21,
28. Oil the following points:
a. Hamnnernnill drive pin — Figure 19
b. Loading auger drive chain — Figure 20
The best time to lubricate chains is im-
mediately after use when chains are
warm.
*c. Loading auger drive chain — Figure 26
d. Gearbox drive chain — Figure 32Ae. Loading auger clutch — Figure 20
f. Winch handle threads — Figures 4-1
29. IMPORTANTI Keep all bevel gears cover-
ed with grease at all times for ease of
operation and long life.
*a. Tank unloading auger drive — Figure
19A
*b. Lower unloading auger drive — Figure
25
*c. Upper unloading auger drive — Figure
20A
*d. Loading auger drive — Figure 22
BEVEL GEARSI COVERED WITH GREASE
SHIELD REMOVED FOR ILLUSTRATION
FIGURE 25
GEAR BOXKeep filled to plug level with SAE 90 multi-
purpose lubricant. Check once a year.
DRIVEN SPROCKET
SPEED CHANGE SPROCKETS
35 R.PM.
SHIELDS REMOVED FOR GLARI
JFIGURE 26
16
AADJUSTMENTS
ALWAYS REPLACE SHIELDS AFTER MAKINGREPAIRS, ADJUSTMENTS OR AFTER LUBRICAT-ING. SHIELDS ARE FOR YOUR PROTECTION;KEEP THEM IN PLACE.
LOADING AUGER SPEED (Mechanical)
The loading auger operating speed is
changed by reversing the double sprocket for
two faster speeds or interchanging the sprock-
ets on the shafts for two slower speeds. SeeFigure 26.
The four speeds for the loading auger are:
Auger R.P.M.
ADJUSTABLE MIXING TUBEThe adjustable mixing tube section is installed
at the factory in the lowest position. It shouldbe used in the lowest position when grindingfree flowing nnaterials. The adjustable section
can be raised to improve the flow of material
with a high percentage of roughage on theModel 355. To relocate the adjustable section,
loosen the bolts on the section and position in
desired location. The adjustable mixing tubeextension is shown in Figure 30 removed fromthe mixing tank for clarity.
FIGURE 30FIGURE 32
LOADING AUGER BRAKE
The loading auger brake is a positive type
and can be adjusted with the jam nuts shownin Figure 31. For correct tension on the brake,
it requires 10 lb.-pull to pull the lever over cen-
ter.
UNLOADING AUGER BRAKE
The unloading auger brake is a positive type
and can be adjusted with jam nuts as shown in
Figure 32. For correct tension on the brake it
requires 40 lb.-pull to pull the lever over center.
The clamp stop bolt shown in Figure 32should be tightened to keep the clamp tight, but
the unloading auger should pivot easily.
GEAR BOX AND TRANSFERAUGER DRIVE CHAINS
Adjust the drive chains as shown in Figure32A by loosening the idler on the drive chain
and moving it as required so that the chain canbe deflected %" with a 25 lb. force in the cen-ter of the span.
SHEAR BOLT
The gear box is shear bolt protected. If shearbolt breaks, always replace with genuine NewHolland shear bolt after determining the causeof failure. Extra shear bolts may be carried in
the convenient carrier shown in Figure 26. Thegear box shear bolt is shown in Figure 32A.
18
FIGURE 32 A
LOADING AUGER PRIMARY DRIVE CHAIN
The loading auger primary drive chain is
tightened by means of the idler shown in Fig-
ure 26, and the secondary drive chain is tight-
ened by means of the idler under the cover
at the lower end of the auger. Both chains
should be adjusted to deflect 1" with a 25pound force in the center of the span.
HAMMER MILL DRIVE BELT (Mechanical Drive)
IT IS IMPORTANT THE HAMMER MILL DRIVEBELT BE KEPT TIGHT AND ALIGNED PROPERLYAT ALL TIMES, to prevent damage to the belt.
To adjust the belt do the following:
1. Loosen the gear box drive chain idler,
shown in Figure 32A, and remove the belt
shield.
2. It is important the belt be aligned proper-
ly. Use a straight edge to check the align-
ment of the hammer mill drive and driven
sheaves before tightening the belt. Shouldthe sheaves need aligned. The alignment
can be accomplished by tightening oneor the other of the nuts on the adjusting
bolts shown in Figure 34. Sheaves should
be aligned to within 1/32".
3. To tighten the belt, loosen the bolts at
E, Figure 34. Back off the nuts at A, Figure
34. Tighten the belt by turning the nuts
equally at C and D in a clockwise direc-
tion. After tensioning the belt check the
belt sheaves for proper alignment. Re-
tighten the nuts at A and E, Figure 34.
FIGURE 33
HAMMERMILL DRIVE BELT (Hydraulic Drive)
This procedure should be followed when ad-
justing the hammermill drive belt on hydraulicunits.
1. Loosen the gear box drive chain. Figure
32A.
2. Loosen the two bolts at A, Figure 33.
FIGURE 34
19
3. It is important the belt be aligned properly.
Use a straight edge to check the alignmentof the hammer mill drive and driven
sheaves before tightening the belt. Shouldthe sheaves need aligned. The alignmenrcan be accomplished by tightening one or
the other of the nuts on the adjusting bolts
shown in Figure 34. Sheaves should bealigned to within 1/32".
To tighten the belt, loosen the bolts at E,
Figure 34, and back off the nuts at A, Fig-
ure 34. Tighten the belt by turning the
nuts equally at C and D in a clockwise di-
rection. After tensioning the belt check the
belt sheaves for proper alignment. Retight-
en the nuts at A, Figure 34.
When properly tightened, the belt will de-
flect W to %" when 50 pounds are ap-
plied at the center of the span of the belt.
For long belt life and proper performanceof the mill, keep the belt properly tightened
at all times.
DO NOT OVERTIGHTEN THE BELT OR DA-MAGE TO THE DRIVE COMPONENTS MAYRESULT.
4. After the belt is properly tensioned, tighten
the two bolts at A, Figure 33.
5. Loosen hose clamp B, Figure 33 and pumpmounting bolts C. Move the hydraulic
pump until all slack is removed from drive
chain and re-tighten the pump mountingbolts at C and tighten hose clamp B.
6. Tighten gear box drive chain shown in Fig-
ure 32A.
REPLACING OR TURNING THE HAMMERMILLHAMMERS
The hammermill hammers are replaceable or
A
can be turned to use four different edges. To
change the hammers or remove them, removethe screen and then remove the pin shown in
Figure 35 through the hole in the hammermill
side sheet. The hammers can then be turned
or new hammers installed as the pin is rein-
stalled through the hammermill plates. It is im-
portant that the hammers and spacers be put
back in the same exact location from which they
were removed, or the rotor may not be bal-
anced and cause serious vibration of the unit
while it is operating. See Figure 36 for ham-mer 'spacer location.
Use new roll pins in the hammer pin.
FIGURE 35
IMPORTANT: WHEN REPLACING HAMMERS,THEY MUST BE REPLACED IN MATCHED SETSOF 36 HAMMERS TO PREVENT VIBRATION OROUT -OF -BALANCE CONDITIONS. SPACERSMUST BE INSTALLED IN POSITIONS SHOWN.
BE CAREFUL!
DO NOT ATTEMPT TO CLEAN OR
ADJUST THE MACHINE WHILE
IT IS RUNNING
20
.o-mm 3|™q[x|[::i|[^
ROD ON REAR SIDE
c Bs3H
^pHfrtH
E:d]m|h:Q[]m|ta
aHoCTgmSD-aM'
HAMMER
n .ROD
:[]:KPIN
FIGURE 36
LOADING AUGER CLUTCH (Mechanical)
The loading auger clutch lever spring is ad-
justed to hold the lever engaged or disengaged.
The collar on the shifting fork rod is adiusted
to fully engage the clutch jaws, with a 1/32"
clearance between the clutch fork and the
clutch.
UNLOADING AUGER CLUTCH (Mechanical)
The unloading auger clutch, Figure 10 shouldbe adjusted so that when the lever is in theengaged position, the clutch jaws mesh fully.
When the lever is in the disengaged positionthe clutch jaws should clear each other by Vs 1o
% inch. Adjustment is made by use of the nutson threaded end of the control rod.
MAINTENANCE
LUBRICATION
Wheel bearings should be repacked every
three years and the bearings taken up to .003-
.010 end play each year.
The drive sheave should be repacked everythree years and the bearings taken up to .0002-
.002 end play each year.
GEAR BOXChange the oil in the gear box once a year.
Refill with SAE 90 all-purpose gear lube. Backlash of the gears should be adjusted to .002-
.015. This is accomplished by shimming.
21
HYDRAULIC DRIVE MODELS
The hydraulic oil reservoir should be filled to
within 4 inches of the top of the filler spout,
approximately 7 gallons, with a good grade of
Type MS lOW, 10W30 or 10W40 motor oil as
shown in Figure 37. When operating in ambienttemperatures of + 10°F or lower, it is recom-
mended using type A transmission fluid. Re-
place the oil filter cartridge after the first 30hours of operation. Replace oil filter cartridge
and clean tank strainer in gasoline every 250hours or once a season thereafter. The tankstrainer screen. Figure 33, is located in the out-
put port of the reservoir and may be removedwhen draining the tank. The oil level in the
reservoir should be checked periodically.
BEVEL GEARSAs the loading and unloading auger bevel
gears wear from use they should be reshimmedto provide as deep a mesh as possible without
FIGURE 37
binding. Add shim washers behind or in front
of gears as required to obtain proper mesh and.030 backlash. These gears do not have ma-chined teeth; therefore they will be excessively
noisy if binding occurs between the gear teeth.
Keep the gear teeth covered with grease at
all times.
SCREENS
Check the grinding screens occasionally.
Screens that have badly rounded edges at the
holes are consuming extra power and should
be replaced if they are badly worn.
PTO SHIELDS
Check the PTO shields occasionally to be surethat they will turn freely and are not dentedbadly. SHIELDS THAT ARE LOCKED TO THESHAFT OR DENTED BADLY ARE DANGEROUSAND SHOULD BE REPLACED. a
A BE CAREFUL! THIS SYMBOL IS USED THROUGHOUT THIS BOOKWHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKETIME TO BE CAREFUL! J
22
SERVICE ADJUSTMENT CHART
PROBLEM
PROBLEM
OPTIONAL EQUIPMENT
BAGGING AHACHMENTThe bagging attachment shown in Figure 38
is used to bag feed at the end of the unloadingauger. It is attached with two spring-loadedpins. DO NOT TRANSPORT THE GRINDER-MIXER WITH THE BAGGER ATTACHED.
The unloading auger is protected by a blow-out lid at the outer end. Therefore, if the bag-ger is unattended and it should completely filL
ATTACH BAGGER TO ADAPTERWITH TWO SPRING LOADED PINS
:ii&^^FIGURE 38
the blowout lid will open so that damage will
not occur at the unloading auger. If the blow-out lid is forced open, it will be necessary to
clean it to have it close properly.
To install the bagger, remove the rubberbelting, install the adapter. Figure 38, with (6)
% X % inch carriage bolts, flat washers, lock
washers and nuts.
FLEXIBLE DOWNSPOUTThe flexible downspout, see Figure 39, is
used to reduce material loss when unloading in
windy conditions. The downspout can be at-
tached to all 8" diameter unloading augers.
Attach the adaoter as shown, the downspoutsnaps onto the adapter.
DEFLECTOR ENDCAPThis attachment clamps on the end of the 10'
ADAPTER
..,^m&
FLEXIBLE DOWNSPOUT
FIGURE 39
base unloading auger using existing clamps, seeFigure 39A. The flexible downspout will adaptto this attachment.
The bagging attachment can also be attachedto the deflector end cap.
FIGURE 39 A
DUST COLLECTOR COVERThe dust collector cover will prevent snow
and rain from entering the dust collector andaccumulating in the transfer auger. See Figure39B.
The cover can be opened or closed by pullingthe rope and flipping the cover over center. Thecover is installed by clamping to the dust col-
lector outlet opening.
SMALL GRAIN LOADING AUGER COVERThe loading auger cover. Figure 39C, is used
25
FIGURE 39 B
to increase the capacity of the loading auger
when grinding small grain. It is not used for
ear corn.
The cover is held in position as shown with
two %" X 3/4" truss head bolts and two %" x %"carriage bolts.
i^OPTtONAL SMALL GRAINMj^ AUGER COVER
FIGURE 39C
MAGNET ATTACHMENTThe magnet is used to remove ferrous metals
such as tramp iron, nails, or small pieces fromfeed materials. See Figure 27. Excessive heavyfeeding or overfeeding the hammermill maycause even ferrous metal objects to go over
the magnet without being stopped. The op-
tional magnet is installed as shown in Figure 45.
REMEMBER, OVERFEEDING MAY CAUSEDAMAGE BECAUSE THE MAGNET DOES NOTHAVE A CHANCE TO STOP THE FERROUSMETAL. Also, remember the magnet does not
stop aluminum or other non-magnetic materials.
THE MAGNET IS INSTALLED FROM THE BOTTOMSIDE Of THE HOPPER.
FIGURE 40
FLOTATION TIRES
High flotation tires are available. They are
intended to be used where soft or extremelyrough ground conditions will be encountered.
See Figure 40. When installing the flotation or
regular tires, make sure the lug bolts are se-
curely tightened. Inflate flotation tires to 40 lbs.
p.s.i. and regular tires to 35 lbs. p.s.i.
FENDERS
Fenders, Figure 40 are available for installa-
tion on the Model 353 and 354 Grinder-Mixer.
Fenders are normally used when extensive road
travel is done.
LOADING AUGER GOVERNORThe loading auger governor. Figure 29 auto-
matically stops and starts the loading auger onmechanical drive units to prevent excessive
overloading, especially helpful for smaller
horsepower tractors. Refer to adjustment of
loading auger governor for specific information
on adjustment and operation.
26
HAY WEDGESHay wedges serve as retarders and prevent
slugging and instantaneous overloads whengrinding hay slabs.
FIGURE 45
10' UNLOADINGAUGER BRACES
AUGER EXTENSION SUPPORTS
I OVER CENTERLATCH
I
10' EXTENSIONSHOWN
FIGURE 43
UNLOADING AUGERSThe 13, 17 and 20 foot unloading augers are
hinged for convenient transporting and yet pro-
vide the long reach when unloading. See"Operation" section and Figure 43 for details
of operation.
27
SPECIFICATIONSMixing Tank Capacity 1 25 cu. ft. (3.4 cu. m)
100 bu. by volume
Overall Height 11 3" (2870 mm)31x13.5x15-16 ply
Overall Width — Loading and UnloadingAugers in Transport Position 97"
Overall Width - Plain Feed Chute . 1 03" (261 6 mm)
Tread Width 64" (1626 mm)
Overall Length 140"
Power Requirements Up to 1 1 h.p.
Screen Sizes Available 3/32" - Vs" - 5/32 - % - ^A - % - ¥8
-
% - Vi - % - 34 . 1 " . 1 1/4 . 1 1/2 openings
HammermillInside Width 213/8" (543 mm)Rotor Diameter . 1 9Va' (489 mm)Drum Diameter 20" (508 mm)Screen Area 635 sq. in. (.4 sqm)Hammers 36
ABE CAREFUL
MOST FARM IMPLEMENT ACCIDENTS CAN BE AVOIDED BY THE OBSERVANCE OF A FEWSIMPLE SAFETY PRECAUTIONS.
1. DON'T CLEAN, LUBRICATE, OR MAKE ANY ADJUSTMENTS ON THE GRINDER-MIXER WHILEIT IS IN MOTION.
2. DON'T START THE GRINDER-MIXER UNTIL YOU KNOW THAT EVERYONE IS CLEAR OF THEMACHINE AND HAVE MADE SURE THAT NO TOOLS ARE LYING ON THE MACHINE.
3. DON'T WORK AROUND THE UNIT IN LOOSE CLOTHING THAT MIGHT CATCH IN ANY OFTHE MOVING PARTS.
4. DON'T ATTEMPT TO PULL MATERIAL FROM ANY PART OF THE GRINDER-MIXER WHILE IT IS
IN OPERATION.
5. MAKE SURE ALL THE TRACTOR AND IMPLEMENT P.T.O. SHIELDS ARE IN PLACE ANDFUNCTIONING PROPERLY.
6. KEEP HANDS CLEAR OF AUGERS WHILE MACHINE IS IN OPERATION.
7. MAKE SURE THE HAMMERMILL IS COMPLETELY STOPPED BEFORE OPENING THE COVER.
8. ALWAYS REPLACE SHIELDS AFTER MAKING REPAIRS, ADJUSTMENTS OR AFTER LUBRICAT-ING. SHIELDS ARE FOR YOUR PROTECTION; KEEP THEM IN PLACE!
28
It
29
J
30
I31
fJLSPER^Y=^^I\EW HOLLAIND
42035510 Form No. 0355—3M—477W Printed In U.S.A.