Contents Checklist The following items should be found inside the box: For you safety Use only approved power supply for NEW7210, using other power supply may damage the device. How to use rechargeable Li-ion battery properly. The battery should be connected when POS terminal is working properly. Use only approved rechargeable battery. Do not dispose of battery in fire or water. Do not expose battery to temperature above 60℃. Store it in the environment between -20℃ and 60℃. Charge with a charger designated for the device. Keep the contact surface of battery away from metal to avoid battery short. Recycle or dispose of expired battery properly complying with local environment requirement. * * * * * * Do not use ethanol or other corrosive liquid to clear the device. NEW7210 Mobile payment terminal PRODUCT MANUAL NEW POS TECHNOLOGY LIMITED NEW POS Technology limited NEW 7210 * 1 POS terminal 1PCS 2 AC Power Supply 1PCS 3 USB Cable 1PCS 4 Li-ion Battery 1PCS 5 Thermal paper roll 1PCS (Optional) 6 Stylus cable 1PCS (Optional) 7 Product Manual 1PCS Product manual
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Contents Checklist
The following items should be found inside the box:
For you safety
Use only approved power supply for NEW7210, using other power supply may damage the
device.
How to use rechargeable Li-ion battery properly.
The battery should be connected when POS terminal is working properly.
Use only approved rechargeable battery.
Do not dispose of battery in fire or water.
Do not expose battery to temperature above 60℃. Store it in the environment between
-20℃ and 60℃.
Charge with a charger designated for the device.
Keep the contact surface of battery away from metal to avoid battery short.
Recycle or dispose of expired battery properly complying with local environment
requirement.
***
***
Do not use ethanol or other corrosive liquid to clear the device.
NEW7210
Mobile payment terminal
PRODUCT MANUAL
NEW POS TECHNOLOGY LIMITED
NEW POS Technology limitedNEW 7210
*
1 POS terminal 1PCS2 AC Power Supply 1PCS3 USB Cable 1PCS4 Li-ion Battery 1PCS5 Thermal paper roll 1PCS (Optional)6 Stylus cable 1PCS (Optional)7 Product Manual 1PCS
Product manual
NEW7210 is a powerful PCI approval,EMV approval payment terminal , with extraordinary
performance in data intensive、multiple applications and EMV transactions.
mobile
Interface Figure
Parts function description Paper holder lid: Holding thermal paper roll ( Φ40X58mm)
Handle: Pull handle to open the paper holder lid
LCD display: 2.8 inch and 320*240 TFT LCD . Optional signature capture function.
Antenna inductive zone:
The zone for tapping contactless card
Key pad: 10 alphanumeric keys,8 functional keys,1 power switch key.
User smart card slot:
Supporting EMV card with contact surface facing up.
Magnetic stripe card reader :
ISO7812,1/2 Tracks or 2/3 Tracks or 1/2/3 Tracks, bi-directional swiping with
the magnetic stripe facing LCD .
Programable LEDs: Programable LEDs to show the status.
Signature pen: Electronic signature pen
Rubber pad: Two rubber pads, anti-vibration/non-slip.
Tag label: Showing model name, rated device parameter.
Barcode Label: Indicating device serial number.
Band Label: Indicating the frequency of communication module.
Back cover: Remove the cover to install battery or SIM/UIM/SAM card.
LED indicator: It indicates the power status of device.
USB Port: USB communication interface.
1NEW7210 Product manual
Top view Back view
Paper holder Lid
LCD display
Keypad
User smart card slotMagnetic stripe card
Rubber pad
Barcode Label
Tag label
Back cover
Stylus pen
Antennainductive zone
Handle
NEW7210 Figure
Product Introduction
NEW POS Technology limited
2NEW7210 Product manual
NEW POS Technology limited
USB Port LED Indicator
Programable Leds(Optional)
Lanyard hole
1. Install the Battery* Remove the back cover of the device;
* Connect the cable of the battery and put the battery to its place ;
* Slide the back cover into its place.
2. Remove the Battery* Remove the back cover of the device;
* Hold the battery brace and lift the battery gently;
* Remove the battery.
3. Install the SIM/UIM card* Remove the back cover of device;
* Insert the card into the SIM/UIM card slot .
4. Remove the SIM/UIM card* Remove the back cover of device;
* Draw the SIM/UIM card out the slot.
Note Make sure that the device is in power off status when installing or removing SIM/UIM card.
5. Switch the device on* Press the power key" ", and the LCD backlight is switched on. Hold the power key for more
than two seconds, then the buzzer of device beeps to show device boots successfully and LCD
shows the corresponding program launch menu;
* The device can be powered by battery or AC power supply.
6. *
the LCD backlight will be switch off.
Switch the device offKeep pressing the power key" "for more than two seconds. The device will beeps and
NEW7210 Product manual
NEW POS Technology limited
Installation Guidance
3 4NEW7210 Product manual
NEW POS Technology limited
7. Loading thermal Paper roll * Pull the handle on the paper holder lid to open the lid up;
* Load the paper roll into the paper holder and extend the paper for 2-3 cm above paper cutter ;
* Close the paper holder lid;
* Please take out the paper shaft and replace the print paper timely when it runs out.
Open the backcover figure
Install the battery figure
Plug cable figure
Remove the battery figure
Install card figure
SIM/UIM
8. Tearing off the paperHold the thermal paper edge, keep the paper at 45 degree angle with the LCD surface, tear off
the paper from left to right with steady speed.
*
5
Note During loading paper roll, keep the thermal sensitive film of paper (external side of paper roll)
facing the thermal head of printer to ensure normal printing.
After long term printing, keep away from thermal printer head for high temperature.
Keep away from the thermal printer paper cutter for the sharp edge.
NEW7210 Product manual
NEW POS Technology limited
How to tear off paper How to swipe card
9. Swiping a Magnetic Stripe Card* During card swiping, the magnetic stripe should be downward and face the LCD of terminal.
Swipe it through the slot located on the right side of the terminal bidirectionally;
* Swipe the card at steady speed.
6
Note During swiping,keep the lower edge of the magnetic stripe card horizontally with the card
guiding surface. Or it maybe lead to swiping card error.
NEW7210 Product manual
10. Contactless card (optional)* For top tapping card, contactless card antenna inductive zone is located on the space on the LCD.
Tap the contactless card above the LCD horizontally for some seconds. The buzzer will prompt
the cardholder the completion of transaction.
NEW POS Technology limited
Loading thermal paper roll figure
b
11. Insert user smart card* Insert smart card with the gold-colored contact surface facing up into the card slot.
View LCD ICC card icon to determine if IC card is inserted into its place. If the IC card icon is
switched on, it indicates OK. While the icon is off, please confirm whether gold-colored contact
surface of card is facing up and IC card is inserted into its place.
12. Battery Charge* Remove the back cover of the device . Insert the rechargeable battery.
Slide the back cover into its place.(If the rechargeable battery is in the device, the step is
unnecessary.)
* Connect the big end of the USB cable to power supply and the small end of cable to the miniUSB
Port on the left side of device. Plug the power supply in the wall socket. LED indicator on the side
of device shows red indicating that battery is in charging status. If the LED indicator shows
green, it indicates battery charge completes.
Note If the device is in powered-off state, Only LED indicator on the side of device shows battery
charge status. While the device is in powered-on state, Battery icon on the LCD display also