-
NEC IPASOLINK 100 INTRODUCTION
Modem Board and Modem
On/OFF Switch
LCT LAN Connection
Port
Main Board
NEC Power cable
9-16 PDH Drop Cable
IPASOLINK 100 is a microwave radio transceiver with a
high-performance carrier packet switch. This versatile transceiver
is compatible with all low-speed to high-speed applications, as
well as with LTE and WiMAX mobile systems. Its advanced switch
functions and excellent performance can meet and surpass every
specification. iPASOLINK 100E can be used in utilities application,
digital TV systems, and Internet medium-speed and high-speed
networks. iPASOLINK 100E's extremely compact IDU requires
minimum
space and can be installed almost anywhere. Its lightweight
compact ODU and small parabolic antenna also needs little
installation space. Boasting the technology used to develop the
industry-leading PASOLINK
series, the iPASOLINK 100E is the best solution for your packet
network requirements
1-8 PDH Drop Cable
-
Introduction NEC IPASOLINK 100
-
NEC IPASOLINK 100
-
NEC IPASOLINK 100
-
High performance Packet Radio High spectrum efficiency QPSK to
256QAM adaptive modulation Carrier class Layer 2 switch function
Various QoS and VLAN functions Easy deployment Minimum foot print
Low power consumption Quick installation Easy maintenance Antenna
direct mount High reliability Advanced error collection Ethernet
ring protection Link aggregation (port redundant) Fan-less natural
cooling Man-machine interface Browser based user interface with
GUI. In-band NMS SNMP v1/v2c/v3 Frequencies 6, 7, 8, 10, 11, 13,
15, 18, 23, 26, 28, 32, 38,
and 42 GHz
Features:----
-
Commissioning Process of NEC IPASOLINK 100
Connect IDU LCT Port by LAN Cable.( Laptop LAN Configuration not
Required) then Open Internet Explorer and enter default IP-
172.17.254.253. and get Following window
then Enter User name and Password
User Name Admin
Password 12345678
Default IP URL 172.17.254.253
-
After Enter User Name Password Login Complete Now ok
-
After Login window will appear
-
Now Start Configure IDU Click on Easy Set Wizard then Easy
setup
-
Define Near End to Far End and Far to Near End IDClick on Set up
and define Site Name or ID then Next ..
-
After define Site ID Click ok then process will complete and
next window Modem Setup will automatic open where we define Planned
frequency
-
MODEM SETUPIn MODEM Setup Click on Setup then define Planned
Channel Spacing ,Modulation,
Radio Mode and Frequency then Next ..ok..
7MHZ
Modulation QPSK
High Cap.
Frequency
-
After Define Click Next..ok..Complete..ok
-
AMR Radio Mapping SetupAfter Modem Setup AMR/Radio Mapping Setup
will Open .Here we Select QPSK then
Next
-
In New Setting QPSK ROW click 2,Generally you will get 1
defined. This is For Activate PDH Channel Port.. IF we define 2 or
more if 1st Port will Faulty we can shift to Channel Port 2. on
both End we have to change PDH Port cable.. Then Next..
-
Then Click Next OK..OK AMR/Radio Mapping Setup will complete
-
Management SetupHere click on Cancel Otherwise For NMS define IP
192.168.0.1 Subnet
255.255.255.248 Default 192.168.0.0 but Uninor not required So
Just Cancel..
-
Traffic Routing Click on E1/STM-1/Cross Connect setting then If
you defined only one in AMR Mapping in
Service No. Just Put 1 or defined 2 in AMR put in Service no . 2
or in Protection in Drop Down Select Main Board left Side and Modem
in right Side both Near and Far End. How many
Channels you want to select then choose 1 or 2 or 3.. then do
OK.
-
Traffic Routing Here we can Select , Delete and ADD Recreate E1
Routing
-
Traffic RoutingIn Provisioining we can separate ADD ,Delete
Traffic Routing as per requirement
-
Traffic Routing and Cable Color Code
NEC IPASOLINK Support 16 PDH Drop . 1-8 Cable Color code is Same
9-16 .if you select Channel No.1 So Both End (Near or Far) Select
Same color code From Same Cable..
1-8 E1 Cable
9-16 E1 Cable
1-8 E1 DDF
Color Code Channel no. 1-8
Channel No 9-16
YELLOW GRAY--RED GRAY ONE NINE
YELLOW GREEN--RED GREEN TWO TEN
YELLOW ORANGE --RED ORANGE
THREE ELEVEN
YELLOW BLUE--RED BLUE FOUR TWELVE
TX RX
It will better to Trace From Main Board Connector if you are
using Channel 1 color code will be yellow Gray-Red Gray in 1-8
Cable or Use LED to Find TX and Rx it may be Simultaneously in One
DDF or
or beside DDF..In Pic. Shown 1 TX and 2 RX in Same DDF
-
RX Level Click Metering and See Tx Power Receive Level
-
SET TIME /DATEClick Equipment Utility and Check in Display PC
Time ok.
-
E1 LoopGo to Maintenance Control then Loop Back Control and 3rd
from top TDM Loop back Control
and Click on ON button as used channel 1 or 2 Now Check BSC
End
-
E1 LoopAfter proper channel E1 Loop Click on Current Status then
Refresh then Click on IDU Particular
E1 will show Normal if Loop ok. Here you can also find accurate
Channel Cable Termination
-
Alarm in IDUClick on Current Status then Click on Refresh button
and Check Active Alarm , Event
Log ,IDU and ODU Alarm
-
FAR END OpenClick on Opposite site Link select and OK Far End IP
Open
-
FAR ENDFar End IP Show 172.18.0.52 again Put User ID and
Password
User Name Admin
Password 12345678
-
FAR END OPEN
-
Conclusion:--
NEC IPASOLINK 100 Configuration Process:-- 1st Check IDU ODU
Earthing and Power Connect LAN Cable in LCT Port Put IP
172.17.254.253 Put User IDAdmin (A should be Caps Only)and
Password12345678 After Login Go to Easy Setup and Put Site ID as
given For Both End Site ID (Near to Far and Far to Near on Both
Sides) Put Frequency, Channel spacing ,Modulation Now AMR Mapping
if you are taking Single E1 Just Click on QPSK and Set Right Side 1
If you want more E1 set 2 (For 2 E1) For Traffic routing go to
Provisioning Add E1 and In protection Block 1st Select Main Board
then Modem
in right side. Same Selection should be Near and Far End. Also
if using Single E1 Select 1 on both Side then ok.
For E1 Color Coding use LED and Trace Cable from Main Board D
Connector. In D connector inside Cable is 1-8 and outside will be
9-16 E1.. also on DDF Board somewhere TX and Rx will be
simultaneously on same DDF or Some time TX will be one DDF and RX
will be one DDF
To see RX Level go to Metering and Check Power and RX Level To
see Internal Alarm in IDU Click on current Status and refresh and
See Alarm in IDU or ODU For E1 loop Click Maintenance Control Loop
Control and 3rd From Top Now On E1 Loop you can See it in
IDU Alarm Log . proper Channel E1 will be Normal if Loop will
Correct To open far End Click on Opposite Side Link and put again
Same User Name and Password. E1 Color Code and E1 Channel No. is
Important to select. Same Channel For Same Color ..Thanks;Krishna
kumarARA Zone