nb73 ea es rev A 58600213 1 - Daisy Data Displays

G5G100-PSystem BoardUser’s Manual

935-G5G101-050GI87040640

Copyright

This publication contains information that is protected by copyright.No part of it may be reproduced in any form or by any means orused to make any transformation/adaptation without the priorwritten permission from the copyright holders.

This publication is provided for informational purposes only. Themanufacturer makes no representations or warranties with respect tothe contents or use of this manual and specifically disclaims anyexpress or implied warranties of merchantability or fitness for anyparticular purpose. The user will assume the entire risk of the use orthe results of the use of this document. Further, the manufacturerreserves the right to revise this publication and make changes to itscontents at any time, without obligation to notify any person orentity of such revisions or changes.

© 2006. All Rights Reserved.

Trademarks

Product names or trademarks appearing in this manual are foridentification purpose only and are the properties of the respectiveowners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in a residentialinstallation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance withthe instruction manual, may cause harmful interference to radiocommunications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by theparty responsible for compliance could void the user's authorityto operate the equipment.

2. Shielded interface cables must be used in order to comply withthe emission limits.

Introduction1

4

Table of Contents

About this Manual................................................................................Warranty.....................................................................................................Static Electricity Precaution................................................................Safety Measures.....................................................................................About the Package...............................................................................Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................Specifications...................................................................................................................................Special Features of the System Board..................................................................

Chapter 2 - Hardware Installation....................................................System Board Layout ..........................................................................................................System Memory..........................................................................................................................CPU.......................................................................................................................................................Jumper Settings............................................................................................................................Rear Panel I/O Ports.............................................................................................................I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................Award BIOS Setup Utility.................................................................................................Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................Drivers, Utilities and Software Applications......................................................Installation Notes.......................................................................................................................

Appendix A - Watchdog Timer.............................................................

Appendix B - System Error Messages...............................................POST Beep.................................................................................................................................Error Messages.........................................................................................................................

Appendix C - Troubleshooting..........................................................Troubleshooting Checklist...............................................................................................

556677

88

12

16161719233243

585897

9999

106

107

108108108

110110

1Introduction

5

About this Manual

An electronic file of this manual is included in the CD. To view theuser’s manual in the CD, insert the CD into a CD-ROM drive. Theautorun screen (Main Board Utility CD) will appear. Click “User’sManual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised frommisuse of the product, inability to use the product, unauthorizedreplacement or alteration of components and productspecifications.

2. The warranty is void if the product has been subjected tophysical abuse, improper installation, modification, accidents orunauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user maynot, under any circumstances, attempt to perform service,adjustments or repairs on the product, whether in or out ofwarranty. It must be returned to the purchase point, factory orauthorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental orconsequencial damages to the product that has been modifiedor altered.

Introduction1

6

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,components or devices even before installing them in your systemunit. Static electrical discharge can damage computer componentswithout causing any signs of physical damage. You must take extracare in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in itsanti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.3. Do all preparation work on a static-free surface.4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.5. Avoid touching the pins or contacts on all modules and

connectors. Hold modules or connectors by their ends.

Important:Electrostatic discharge (ESD) can damage your processor, diskdrive and other components. Perform the upgrade instructionprocedures described at an ESD workstation only. If such astation is not available, you can provide some ESD protectionby wearing an antistatic wrist strap and attaching it to a metalpart of the system chassis. If a wrist strap is unavailable,establish and maintain contact with the system chassisthroughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:• Use the correct AC input voltage range.....

To reduce the risk of electric shock:• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,cover the system chassis before plugging the power cord.

Battery:• Danger of explosion if battery incorrectly replaced.• Replace only with the same or equivalent type recommend by

the manufacturer.• Dispose of used batter ies according to the batter y

manufacturer’s instructions.

1Introduction

7

About the Package

The system board package contains the following items. If any ofthese items are missing or damaged, please contact your dealer orsales representative for assistance.

The system boardOne IDE cableOne Serial ATA data cableOne Serial ATA power cableOne “Main Board Utility” CDOne I/O shield

The system board and accessories in the package may not comesimilar to the information listed above. This may differ in accordanceto the sales region or models in which it was sold. For moreinformation about the standard package in your region, pleasecontact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will needat least the following internal components.

• A CPU• Memory module• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to usewhich will normally include at least a keyboard, a mouse and a videodisplay monitor.

Introduction1

8

Chapter 1 - Introduction

Features

Processor• Intel® Pentium® M Dothan processor

- 533MHz/400MHz system data bus• Intel® Celeron® M processor

- 400MHz system data bus• Processor socket: mPGA479M

The following Intel Celeron® M 65nm processors are NOTsupported: 410, 420, 423, 430, 440 and 450.

Chipset• Intel® 915GM chipset

- Intel® 915GM Graphics Memory Controller Hub (GMCH)- Intel® 82801FBM I/O Controller Hub (ICH6M)

System Memory• Two 184-pin DDR SDRAM DIMM sockets• Supports single channel (64-bit wide) memory interface• Unbuffered PC2700 (DDR333) DDR SDRAM DIMM• Supports maximum of 2GB system memory using 256Mbit,

512Mbit or 1Gbit technology for x8 and x16 devices, non-ECCmemory

BIOS• Award BIOS• 4Mbit flash memory

Energy Efficient Design• Suppor ts ACPI specification and OS Directed Power

Management• Supports ACPI STR (Suspend to RAM) function• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse- Wake-On-USB Keyboard/Mouse- Wake-On-LAN- Wake-On-Ring- RTC timer to power-on the system

• System power management supported

1Introduction

9

• CPU stopped clock control• Microsoft®/Intel® APM 1.2 compliant• Soft Power supported - ACPI v1.0a specification• AC power failure recovery

Damage Free Intelligence• Monitors CPU/system temperature and overheat alarm• Monitors CPU(V), +1.5V, +3.3V, +5V, +12V, -12V, VBAT(V) and

5VSB(V) voltages and failure alarm• Monitors CPU/chassis/2nd fan speed and failure alarm• Read back capability that displays temperature, voltage and fan

speed• Watchdog timer function

Onboard Graphics Features• Integrated display interface

- Analog CRT DAC interface support- Supports max DAC frequency up to 400MHz- 24-bit RAMDAC support- Up to 2048x1536 mode support

- Digital LVDS interface support- Integrated dual channel LVDS interface support- Suppor ts 25 to 112MHz single/dual channel LVDS

interface- Single channel LVDS interface support: 1 x 18 bpp- Dual channel LVDS interface support: 2 x 18 bpp

• Internal graphics features- DVMT 3.0 support

- 1MB or 8MB of pre-allocated memory supported- Intel® Dual-Frequency Graphics Technology- Intel® Smart 2D Display Technology- Dual Independent display pipes- 32-bit hardware cursor supported- 2D graphics engine

- Optimized 256-bit BLT engine- 32-bit Alpha blended cursor

Introduction1

10

- High quality 3D setup and render engine- Triangle lists, strips and fans- Supports D3D and OGL pixelization rules- Shadow maps- Zone rendering 2.0 support

- High quality texture engine- 533 MegaTexel/sec performance - 266 Mpixel/sec fill rate

up to 2 bilinear textures- Per-pixel perspective corrected texture mapping

- 3D graphics rendering enhancements- 16- and 24-bit Z buffering- Maximum 3D resolution supported: 1600x1200x32

Onboard Audio Features• Realtek ALC655• 16-bit stereo full-duplex codec with independent variable sam-

pling rate• High quality differential CD input• True stereo line level outputs• S/PDIF-in/out interface• 5.1-channel audio output

Onboard LAN Features• RTL8110SB Gigabit ethernet controller• Supports 10Mbps, 100Mbps and 1Gbps data transmission• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

Serial ATA Interface• Supports two SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification (1.5Gbps interface)

IDE Interface• Supports up to UltraDMA 100Mbps hard drives• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

1Introduction

11

Rear Panel I/O Ports• 1 mini-DIN-6 PS/2 mouse port• 1 mini-DIN-6 PS/2 keyboard port• 3 DB-9 serial ports• 1 DB-15 VGA port• 1 RJ45 LAN port• 4 USB 2.0/1.1 ports• Mic-in, line-in and line-out

I/O Connectors• 2 connectors for 4 additional external USB 2.0/1.1 ports• 1 connector for 1 external serial port• 1 LCD brightness control connector• 1 LVDS LCD panel connector• 1 LCD/Inverter power connector• 1 LCD AUX power connector• 1 DIO connector• 1 front audio connector for line-out and mic-in jacks• 1 CD-in internal audio connector• 1 S/PDIF-in/out connector• 1 connector for IrDA interface• 2 Serial ATA connectors• 1 40-pin IDE connector• 1 floppy connector (FPC type)• 1 20-pin ATX power connector• 1 front panel connector• 1 chassis open connector• 3 fan connectors

Expansion Slots• 1 PCI slot for PCI expansion card or customized riser card for 1,

2 or 3 PCI slots expansion (for low profile PCI card only)

Compatibility• PCI 2.2 and AC ’97 compliant

PCB• 6 layers, mini-ITX form factor• 17cm (6.7") x 17cm (6.7")

Introduction1

12

Special Features of the System Board

Watchdog Timer

The Watchdog Timer function allows your application to regularly“clear” the system at the set time interval. If the system hangs orfails to function, it will reset at the set time interval so that yoursystem will continue to operate.

DDR

Double Data Rate SDRAM (DDR SDRAM) is a type of SDRAMthat doubles the data rate through reading and writing at both therising and falling edge of each clock. This effectively doubles thespeed of operation therefore doubling the speed of data transfer.

5.1-channel audio output

The audio jacks at the rear panel will support 6-channel audio onlywhen the audio utility is configured to support this function. The mic-in at the rear will be disabled. Use the front audio’s mic-in jack.

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digitalaudio signals to a device without having to be converted first to ananalog format. This prevents the quality of the audio signal fromdegrading whenever it is converted to analog. S/PDIF is usuallyfound on digital audio equipment such as a DAT machine or audioprocessing device. The S/PDIF connector on the system board sendssurround sound and 3D audio signal outputs to amplifiers andspeakers and to digital recording devices like CD recorders.

Serial ATA Interface

Serial ATA is a storage interface that is compliant with SATA 1.0specification. With speed of up to 1.5Gbps, it improves hard driveperformance faster than the standard parallel ATA whose datatransfer rate is 100MB/s.

1Introduction

13

IrDA Interface

The system board is equipped with an IrDA connector for wirelessconnectivity between your computer and peripheral devices. TheIRDA (Infrared Data Association) specification supports datatransfers of 115K baud at a distance of 1 meter.

USB Ports

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a marked improvement in devicetransfer speeds between your computer and a wide range ofsimultaneously accessible external Plug and Play peripherals.

Dual Function Power Button

Depending on the setting in the “Soft-Off By PWR-BTTN” field ofthe Power Management Setup, this switch will allow the system toenter the Soft-Off or Suspend mode.

Wake-On-Ring

This feature allows the system that is in the Suspend mode or SoftPower Off mode to wake-up/power-on to respond to calls comingfrom an external modem .

Important:If you are using a modem add-in card, the 5VSB power sourceof your power supply must support a minimum of ≥720mA.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft PowerDown (Soft-Off) PC. It is supported via the onboard LAN port orvia a PCI LAN card that uses the PCI PME (Power ManagementEvent) signal. However, if your system is in the Suspend mode, youcan power-on the system only through an IRQ or DMA interrupt.

Important:The 5VSB power source of your power supply must support≥720mA.

Introduction1

14

Wake-On-PS/2 Keyboard/Mouse

This function allows you to use the PS/2 keyboard or PS/2 mouseto power-on the system.


Wake-On-USB Keyboard/Mouse

This function allows you to use a USB keyboard or USB mouse towake up a system from the S3 (STR - Suspend To RAM) state.

Important:If you are using the Wake-On-USB Keyboard/Mouse function for2 USB ports, the 5VSB power source of your power supplymust support ≥1.5A. For 3 or more USB ports, the 5VSBpower source of your power supply must support ≥2A.

RTC Timer to Power-on the System

The RTC installed on the system board allows your system toautomatically power-on on the set date and time.

ACPI STR

The system board is designed to meet the ACPI (Advanced Con-figuration and Power Interface) specification. ACPI has energy savingfeatures that enables PCs to implement Power Management andPlug-and-Play with operating systems that support OS Direct PowerManagement. Currently, only Windows®®®®® 98/2000/ME/XP supportsthe ACPI function. ACPI when enabled in the Power ManagementSetup will allow you to use the Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off thesystem at once by pressing the power button or selecting “Standby”when you shut down Windows®®®®® 98/2000/ME/XP without having togo through the sometimes tiresome process of closing files,applications and operating system. This is because the system iscapable of storing all programs and data files during the entireoperating session into RAM (Random Access Memory) when itpowers-off. The operating session will resume exactly where you leftoff the next time you power-on the system.

1Introduction

15

Important:The 5VSB power source of your power supply must support≥1A.

Virus Protection

Most viruses today destroy data stored in hard drives. The systemboard is designed to protect the boot sector and partition table ofyour hard disk drive.

16

2 Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

17

2Hardware Installation

System Memory

Warning:Electrostatic discharge (ESD) can damage your system board, proces-sor, disk drives, add-in boards, and other components. Perform theupgrade instruction procedures described at an ESD workstation only.If such a station is not available, you can provide some ESDprotection by wearing an antistatic wrist strap and attaching it to ametal part of the system chassis. If a wrist strap is unavailable,establish and maintain contact with the system chassis throughoutany procedures requiring ESD protection.

The system board supports DDR SDRAM DIMM. Double DataRate SDRAM (DDR SDRAM) is a type of SDRAM that doubles thedata rate through reading and writing at both the rising and fallingedge of each clock. This effectively doubles the speed of operationtherefore doubling the speed of data transfer.

BIOS Setting

Configure the system memory in the Advanced Chipset Featuressubmenu of the BIOS.

.

.

.

.

.

.

.

.

DDR 1

DDR 2

18


Installing the DIM Module

A DIM module simply snaps into a DIMM socket on the systemboard. Pin 1 of the DIM module must correspond with Pin 1 of thesocket.

1. Pull the “tabs” which are at the ends of the socket to the side.

2. Position the DIMM above the socket with the “notch” in themodule aligned with the “key” on the socket.

3. Seat the module ver tically into the socket. Make sure it iscompletely seated. The tabs will hold the DIMM in place.

Pin 1

Notch

Key

Tab Tab

19


CPU

Overview

The system board is equipped with a surface mount mPGA479M(Socket 479) CPU socket. This socket is exclusively designed forinstalling an Intel® Pentium® M / Celeron® M processor.

Installing the CPU

1. Make sure the PC and all other peripheral devices connected toit has been powered down.

2. Disconnect all power cords and cables.

3. Locate the 479-pin CPU socket on the system board.

4. Use a screwdriver to turn the screw to its unlock position.

Lock

Unlock

20


5. Position the CPU above the socket. The gold triangular mark onthe CPU must align with pin 1 of the CPU socket.

Important:Handle the CPU by its edges and avoid touching the pins.

6. Insert the CPU into the socket until it is seated in place. TheCPU will fit in only one orientation and can easily be insertedwithout exerting any force. Use a screwdriver to turn the screwto its lock position.

Important:Do not force the CPU into the socket. Forcing the CPU intothe socket may bend the pins and damage the CPU.

Goldtriangularmark

Pin 1 of the socket

21


Installing the Fan and Heat Sink

The CPU must be kept cool by using a CPU fan with heat sink.Without sufficient air circulation across the CPU and heat sink, theCPU will overheat damaging both the CPU and system board.

Note:• Use only certified fan and heat sink.• The fan and heat sink package usually contains the fan and

heat sink assembly, and an installation guide. If the installa-tion procedure in the installation guide differs from the onein this section, please follow the installation guide in thepackage.

CPU fan andheat sink assembly

Retentionmodule base

1. Match and insert the screw holes of the retention module baseto the mounting holes around the CPU socket from the bottomthrough the top of the system board.

Screw hole

Screw hole

Screw hole

Screw hole

Buttom view of the system board

22


2. Place the heat sink on top of the CPU. The 4 screws around theheat sink must match the screw holes of the retention modulebase. Refer to the figure below for the correct position of theheat sink. This is important so that the fan / heat sink willprovide adequate cooling to the components of the systemboard.

Turn each Phillips head screw half way down first to initiallystabilize the heat sink onto the system board, then finally tighteneach screw.

Important:Do not turn the first screw all the way down followed bythe next and so on. This is to avoid imbalance which mightcause cracks or fractures to the CPU and/or heat sinkassembly.

23


Jumper Settings

Clear CMOS Data

If you encounter the following,

a) CMOS data becomes corrupted.b) You forgot the supervisor or user password.

you can reconfigure the system with the default values stored in theROM BIOS.

To load the default values stored in the ROM BIOS, please followthe steps below.

1. Power-off the system and unplug the power cord.

2. Set J_CMOS1 pins 2 and 3 to On. Wait for a few seconds andset J_CMOS1 back to its default setting, pins 1 and 2 On.

3. Now plug the power cord and power-on the system.

2-3 On:Clear CMOS Data

1-2 On: Normal(default)

J_CMOS1

1

32

1

32

24


JP4 is used to select the power of the PS/2 keyboard/mouse port.Selecting 5VSB will allow you to use the PS/2 keyboard or PS/2mouse to wake up the system.

BIOS Setting

Configure the PS/2 keyboard/mouse wake up function in theIntegrated Peripherals submenu (“Super IO Device” section) of theBIOS. Refer to chapter 3 for more information.


PS/2 Power Select

1-2 On: 5V(default)

2-3 On: 5VSB

JP4 3

12

3

12

25


USB Power Select

USB 5-8(JP5)

JP1 and JP5 are used to select the power of the USB ports.Selecting 5VSB will allow you to use the USB keyboard or USBmouse to wake up the system.

BIOS Setting

“USB KB Wake-Up From S3” in the Power Management Setupsubmenu of the BIOS must be set to Enabled. Refer to chapter 3for more information.


1-2 On: 5V(default)

2-3 On: 5VSB

USB 1-4(JP1)

1-2 On: 5V(default)

2-3 On: 5VSB

31 231 2

3

12

3

12

26


LCD/Inverter Settings

JP7 is used to select the power supplied to the LCD panel and toconfigure the inverter.

JP7

Important:Before powering-on the system, make sure JP7’s settingmatches the LCD panel’s specification. Selecting the incorrectvoltage will seriously damage the LCD panel.

LCD/Inverter Settings - JP7

5V3.3V12V

Panel Power1-3 On3-5 On7-9 On

5V12V

Inverter On Level2-4 On4-6 On

Active LowActive High

Inverter On/Off Select8-10 On10-12 On

27


LCD Brightness Control (Voltage Level Adjust)

J10

Use J10 to connect to the LCD Brightness Control button of theLCD Display Panel. It is used to adjust the brightness of the LCDDisplay Panel. Increasing or decreasing the voltage to control theLCD panel’s brightness varies among Inverters. You must refer to theInverter’s specification to make the appropriate adjustment to thebrightness of the LCD panel.

3

12

1-2 On:Increases the voltage level

2-3 On:Decreases the voltage level

28


JP3 is used to set COM 4 to RS-232 or RS-485. If the serial deviceconnected to this port requires 5V/12V power from the systemboard, set JP3 pins 1-3, 2-4, 9-11 and 10-12 to On. This settingautomatically sets COM 4 at RS-232.

COM 4 RS232/RS485/AUX Select

JP3

JP31-3, 2-4, 7-9, 8-10 On3-5, 4-6, 7-9, 8-10 On1-3, 2-4, 9-11 (12V),10-12 (5V) On

COM 4 RS232/RS485/AUX SelectRS232 (default)RS485Auxiliary power

29


COM 2 is an RS-232 port. If the serial device connected to thisport requires 5V/12V power from the system board, set JP2 pins3-5 and 4-6 to On. Otherwise, leave this jumper’s setting at 1-3, 2-4On.

COM 2 RS232/AUX Select

JP2

3-5 (5V),4-6 (12V) On:Auxiliary power

1-3, 2-4 On:RS232

(default)

1

3

2

6

4

5

1

3

2

6

4

5

30


JP10

Power-on Select

1-2 On:Power-on via

AC power

2-3 On:Power-on viapower button

(default)

JP10 is used to select the method of powering on the system. If youwant the system to power-on whenever AC power comes in, setJP10 pins 1 and 2 to On. If you want to use the power button, setpins 2 and 3 to On.

Important:If you want the system to automatically power-on when powerreturns after an AC power failure, you must:

1. Set JP10 pins 1 and 2 to On.2. The PWRON After PWR-Fail field must be set to "On".

(Integrated Peripherals submenu, Super I/O Device sectionof the BIOS).

31 231 2

31


Pentium M Processor FSB Select

JP6

JP6 is used to select the front side bus of a Pentium® M processor.

Important:Overclocking may result to the CPU’s or system’s instability andare not guaranteed to provide better system performance. Ifyou are unable to boot your system due to overclocking, makesure to set this jumper back to its default settings.

4-6 On:Dothan-A step

FSB400

3-5, 4-6 On:Dothan-A step

FSB533

1-3, 2-4 On:Dothan-B step

1

3

2

6

4

5

1

3

2

6

4

5

1

3

2

6

4

5

32


Rear Panel I/O Ports

The rear panel I/O ports consist of the following:

• PS/2 mouse port• PS/2 keyboard port• COM ports• VGA port• LAN port• USB ports• Mic-in jack• Line-in jack• Line-out jack

PS/2K/B

COM 2 USB 3USB 1-2VGA

Line-out

Line-in

Mic-inPS/2

MouseLAN

USB 4

COM 1 COM 4

33


PS/2 Mouse and PS/2 Keyboard Ports

The system board is equipped with an onboard PS/2 mouse(Green) and PS/2 keyboard (Purple) ports - both at location CN1of the system board. The PS/2 mouse port uses IRQ12. If a mouseis not connected to this port, the system will reserve IRQ12 forother expansion cards.

Warning:Make sure to turn off your computer prior to connecting ordisconnecting a mouse or keyboard. Failure to do so maydamage the system board.

Wake-On-PS/2 Keyboard/Mouse

The Wake-On-PS/2 Keyboard/Mouse function allows you to use thePS/2 keyboard or PS/2 mouse to power-on the system. To use thisfunction:

• Jumper Setting:JP4 must be set to “2-3 On: 5VSB”. Refer to “PS/2 PowerSelect” in this chapter for more information.

.

.

.

.

.

.

.

.

PS/2 Mouse

PS/2 Keyboard

34


• BIOS Setting:Configure the PS/2 wake up function in the Integrated Peripheralssubmenu (“Super IO Device” section) of the BIOS. Refer tochapter 3 for more information.


35


COM 1

COM 2

Serial Ports

The system board is equipped with 3 onboard serial ports atlocations CN5 (COM 1 and COM 2) and CN6 (COM 4). It is alsoequipped with a 9-pin connector at location J3 (COM 3). Theseserial ports are RS-232 and/or RS-485 (COM 4 only) asynchronouscommunication ports with 16C550A-compatible UARTs that can beused with modems, serial printers, remote display terminals, andother serial devices.

To connect COM 3, insert the connector that is attached to theserial port cable to J3. Make sure the colored stripe on the ribboncable is aligned with pin 1 of J3.

Important:If the LCD Display Panel that is connected to the LVDS LCDPanel connector supports touch screen, DO NOT connect aserial device to COM 3 because the touch screen function isinternally connected to COM 3.

1

9

2

CDTD

RDDTR

GNDRTS

DSRCTS

RI

COM 3

COM 4

36


Jumper Setting

If the serial device connected to COM 2 and/or COM 4 requiresauxiliary power from the system board, set JP2 and/or JP3appropriately. Refer to “COM 2 RS232/AUX Select” and “COM 4RS232/RS485/AUX Select” in this chapter for more information.

BIOS Setting

Configure the serial ports in the Integrated Peripherals submenu ofthe BIOS. Refer to chapter 3 for more information.

37


VGA Port

The system board can only be used with an analog video monitor.Connect the monitor’s 15-pin D-shell cable connector to the VGAport (Blue) at location CN6. If your monitor supports analog videobut does not have a 15-pin D-shell connector, see your monitordealer for the adapter or optional cable. After you plug the monitorcable into the VGA port, gently tighten the cable screws to hold theconnector in place. Some monitors have a switch that choosesbetween analog and TTL (or digital) operation. If your monitor hassuch a switch, set it for analog.

BIOS Setting

Configure the onboard VGA in the Advanced Chipset Featuressubmenu of the BIOS.

Driver Installation

Install the “Intel Graphics Drivers”. Refer to chapter 4 for more infor-mation.

VGA

38


RJ45 Fast-Ethernet Port

The system board is equipped with an onboard RJ45 LAN port atlocation CN4. This port allows the system board to connect to alocal area network by means of a network hub.

BIOS Setting

Enable or disable the onboard LAN in the Integrated Peripheralssubmenu (“Onboard Device” section) of the BIOS. Refer to chapter3 for more information.

Driver Installation

Install the “LAN Drivers”. Refer to chapter 4 for more information.

LAN

39


Universal Serial Bus Connectors

The system board supports 8 USB 2.0/1.1 ports. USB allows dataexchange between your computer and a wide range ofsimultaneously accessible external Plug and Play peripherals.

The 4 onboard USB 2.0/1.1 ports (Black) are at locations CN4(USB 1-2) and CN3 (USB 3-4).

The USB 5-6 and USB 7-8 connectors allow you to connect 4additional USB 2.0/1.1 ports. The USB ports may be mounted on acard-edge bracket. Install the card-edge bracket to the systemchassis then insert the connector that is attached to the USB portcables to the system board’s USB 5-6 or USB 7-8 connectors

BIOS Setting

Configure the onboard USB in the Integrated Peripherals submenu(“Onboard Device” section) of the BIOS. Refer to chapter 3 formore information.

USB 5-6USB 7-8

USB 4

USB 3

USB 2

USB 1

1

VC

C-D

ata

+D

ata

GN

DKe

y

VC

C-D

ata

+D

ata

GN

DN

. C.

2 109

40


Driver Installation

You may need to install the proper drivers in your operating systemto use the USB device. Refer to your operating system’s manual ordocumentation for more information.

Refer to chapter 4 for more information about installing the USB 2.0drivers.

Wake-On-USB Keyboard/Mouse

The Wake-On-USB Keyboard/Mouse function allows you to use aUSB keyboard or USB mouse to wake up a system from the S3(STR - Suspend To RAM) state. To use this function:

• Jumper Setting:JP1 and/or JP5 must be set to “2-3 On: 5VSB”. Refer to “USBPower Select” in this chapter for more information.

• BIOS Setting:“USB KB Wake-Up From S3” in the Power Management Setupsubmenu of the BIOS must be set to Enabled. Refer to chapter3 for more information.


41


Audio (Rear Audio and Front Audio)

Front audio1

Mic

Mic

Pow

erA

uD_R

_Out

N. C

.A

uD_L

_Out

GN

DA

uD_V

cc

Key

2 109

AuD

_R_R

etur

n

AuD

_L_R

etur

n

Rear audio

Rear Audio

The system board is equipped with 3 audio jacks at location CN2.A jack is a one-hole connecting interface for inserting a plug.

• Mic-in (Pink)In a 2-channel or 4-channel mode, this jack is used to connect anexternal microphone. In a 6-channel mode, this jack functions asCenter/Subwoofer.

• Line-in (Light Blue)In a 2-channel mode, this jack is used to connect any audiodevices such as Hi-fi set, CD player, tape player, AM/FM radiotuner, synthesizer, etc. In a 4-channel or 6-channel mode, this jackfunctions as rear right/left speaker out.

Line-out

Line-in

Mic-in

42


Front Audio

The front audio connector (J2) allows you to connect to the line-outand mic-in jacks that are at the front panel of your system. Using theline-out and mic-in jacks will disable the rear audio’s line-out and mic-in functions.

Remove the jumper caps from pins 5-6 and pins 9-10 of J2 prior toconnecting the front audio cable connector. Make sure pin 1 of thecable connector is aligned with pin 1 of J2. If you are not using thisconnector, make sure to replace the jumper caps back to theiroriginal pin locations.

Driver Installation

Install the “Audio Drivers”. Refer to chapter 4 for more information.

The front audio is disabled.The rear audio is enabled.

The front audio is enabled.The rear audio is disabled.

Pins 5-6 and 9-10 short(default)

Pins 5-6 and 9-10 open

2-channel

Line-in

Line-out

Mic-in

4-channel

Rear R/L

Front R/L

Mic-in

6-channel

Rear R/L

Front R/L

Center/Subwoofer

Light Blue

Lime

Pink

• Line-out (Lime)In a 2-channel mode, this jack is used to connect a headphoneor external speakers. In a 4-channel or 6-channel mode, this jackfunctions as front right/left speaker out.

43


I/O Connectors

CD-in Internal Audio Connector

The CD-in connector is used to receive audio from a CD-ROMdrive, TV tuner or MPEG card.

4

1Left audiochannel

Right audiochannelGroundGround

44


S/PDIF Connector

The S/PDIF connector is used to connect external S/PDIF ports. YourS/PDIF ports may be mounted on a card-edge bracket. Install thecard-edge bracket to the system chassis then connect the audiocable connector to SPDIF1. Make sure pin 1 of the audio cableconnector is aligned with pin 1 of SPDIF1.

1 5

+5VKey

SPDIF outGND

SPDIF in

45


LVDS LCD Panel, LCD/Inverter Power and LCD AUX PowerConnectors

The system board allows you to connect a LCD Display Panel bymeans of the LVDS LCD panel connector (CN7) and the LCD/Inverter power connector (CN8). These connectors transmit videosignals and power from the system board to the LCD Display Panel.The LCD AUX power connector is used to connect auxiliary powerto the LCD panel. Refer to the next page for the pin functions ofthese connectors.

Jumper Settings

Refer to the “Jumper Settings” section in this chapter for settingsrelevant to the LCD panel.

LVDS LCD Panel

LCD/InverterPower

3

12LCD AUX

Power

11 8

46


Pins

1

2

3

4

Function

+12V

+12V

Panel Backlight On/Off Control

+3.3V

Pins

5

6

7

8

Function

Panel Power

Panel Inverter Brightness Voltage Control

GND

GND

Pins

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

Function

GND

N. C.

N. C.

GND

LVDS_Out2+

LVDS_Out2-

GND

LVDS_Out1+

LVDS_Out1-

GND

LVDS_Out0+

LVDS_Out0-

GND

LVDS_CLK1+

LVDS_CLK1-

GND

COM3_DTR

COM3_RTS

COM3_RD

COM3_CTS

Pins

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

Function

GND

N. C.

N. C.

GND

LVDS_Out6+

LVDS_Out6-

GND

LVDS_Out5+

LVDS_Out5-

GND

LVDS_Out4+

LVDS_Out4-

GND

LVDS_CLK2+

LVDS_CLK2-

GND

COM3_TD

COM3_RI

COM3_DSR

COM3_DCD

LVDS LCD Panel Connector

LCD/Inverter Power Connector

LCD AUX Power Connector

Pins

1

2

3

Function

Panel Power

Ground

Panel Power

47


DIO Connector

The DIO (Digital I/O) connector at location J11 provides powering-on function of an external device that is connected to this connector.

21

19

Pins

1

3

5

7

9

11

13

15

17

19

Function

GND

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

DIO0

GND

Pins

2

4

6

8

10

12

14

16

18

Function

+12V

+12V

GND

VCC

VCC

GND

V_5P0_STBY

V_5P0_STBY

GND

Digital I/O Connector

48


Floppy Disk Drive Connector

The system board is equipped with a 26-pin FPC type floppy diskdrive connector. Only connect a 1.44MB slim-type floppy disk drive.Floppy drives other than the one mentioned above are optional.Refer to the next page for the pin function of this connector.

Connecting the Floppy Disk Drive Cable

Install one end of the floppy disk drive cable into the floppy diskconnector (FDC1) on the system board and the other end of theconnector to the floppy drive. Pin 1 of the cable must align with pin1 of FDC1.

BIOS Setting

Enable or disable this function in the Integrated Peripherals submenu(“Super IO Device” field) of the BIOS. Refer to chapter 3 for moreinformation.

1

49


Pins

1

3

5

7

9

11

13

15

17

19

21

23

25

Function

5V

5V

5V

N. C.

N. C.

N. C.

DRVDE0

GND

GND

GND

GND

GND

GND

Pins

2

4

6

8

10

12

14

16

18

20

22

24

26

Function

INDEX#

DR0#

DSKCH#

N. C.

MTR0#

DIR#

STEP#

WDATA#

WGATE#

TRK0#

WRPRO#

RDATA#

HDSEL#

FPC Type FDD Connector

50


Serial ATA Connectors

The system board is equipped with two Serial ATA connectors forconnecting Serial ATA devices. Connect one end of the Serial ATAcable to SATA 1 or SATA 2 and the other end to your Serial ATAdevice.

BIOS Setting

Configure the onboard Serial ATA in the Integrated Peripheralssubmenu (“OnChip IDE Device” section) of the BIOS. Refer tochapter 3 for more information.

SATA 1

SATA 21 7

GN

DT

XP

TX

NG

ND

RX

NR

XP

GN

D

1 7

51


IDE Disk Drive Connectors

The system board is equipped with a shrouded PCI IDE headerthat will interface two Enhanced IDE (Integrated Drive Electronics)disk drives. To prevent improper IDE cable installation, the shroudedPCI IDE header has a keying mechanism. The 40-pin connector onthe IDE cable can be placed into the header only if pin 1 of theconnector is aligned with pin 1 of the header.

Connecting the IDE Disk Drive Cable

The IDE connector supports 2 devices, a Master and a Slave. Usean IDE ribbon cable to connect the drives to the system board. AnIDE ribbon cable have 3 connectors on them, one that plugs into anIDE connector on the system board and the other 2 connects toIDE devices. The connector at the end of the cable is for the Masterdrive and the connector in the middle of the cable is for the Slavedrive.

Install one end of the IDE cable into the IDE header on the systemboard and the other connectors to the IDE devices.

40 39

2 1

52


Adding a Second IDE Disk Drive

When using two IDE drives, one must be set as the master and theother as the slave. Follow the instructions provided by the drivemanufacturer for setting the jumpers and/or switches on the drives.

The system board supports Enhanced IDE or ATA-2, ATA/33,ATA/66 and ATA/100 hard drives. We recommend that you usehard drives from the same manufacturer. In a few cases, drives fromtwo different manufacturers will not function properly when usedtogether. The problem lies in the hard drives, not the system board.

Important:If you encountered problems while using an ATAPI CD-ROMdrive that is set in Master mode, please set the CD-ROM driveto Slave mode. Some ATAPI CD-ROMs may not be recognizedand cannot be used if incorrectly set in Master mode.

BIOS Setting

Configure the onboard IDE in the Integrated Peripherals submenu(“OnChip IDE Device” section) of the BIOS. Refer to chapter 3 formore information.

53


IrDA Connector

Connect your IrDA cable to connector IR1 on the system board.

Note:The sequence of the pin functions on some IrDA cable may bereversed from the pin function defined on the system board.Make sure to connect the cable to the IrDA connectoraccording to their pin functions.

BIOS Setting

Configure the onboard IrDA in the Integrated Peripherals submenuof the BIOS to the type of IrDA standard supported by yourdevice.

Driver Installation

You may need to install the proper drivers in your operating systemto use the IrDA function. Refer to your operating system’s manual ordocumentation for more information.

1 5

VCCN. C.

IRRXGround

IRTX

54


Cooling Fan Connectors

Connect the CPU fan’s cable connector to the CPU fan connectoron the system board. The 2nd fan and system fan connectors areused to connect additional cooling fans. The cooling fans will provideadequate airflow throughout the chassis to prevent overheating theCPU and system board components.

BIOS Setting

The “PC Health Status” submenu of the BIOS will display the currentspeed of the cooling fans. Refer to chapter 3 for more information.

2ndfan

CPUfan

System fan

3 1

GroundPower

Sense

SensePowerGround1

3

55


The system board supports the chassis intrusion detection function.Connect the chassis intrusion sensor cable from the chassis to thechassis open connector (J4). Whenever a chassis component hasbeen removed, the sensor sends signal to the connector alerting youof a chassis intrusion event.

Hardware Monitor for Windows

Install the “Hardware Monitor for Windows” utility. By default, thechassis intrusion detection function is disabled. When enabled, awarning message will appear when the chassis is open. The utility canalso be configured so that a beeping alarm will sound when thechassis is open. Refer to the “Hardware Monitor for Windows”section in chapter 4 for more information.

Chassis Open Connector

21 Ground

Chassis signal

56


Power Connectors

Use a power supply that complies with the ATX12V Power SupplyDesign Guide Version 1.1. An ATX12V power supply has a standard20-pin ATX main power connector that must be inserted onto theP1 connector.

The system board requires a minimum of 150 Watt power supplyto operate. Your system configuration (amount of memory, add-incards, peripherals, etc.) may exceed the minimum power requirement.To ensure that adequate power is provided, use a 250 Watt (orgreater) power supply.

+12

V

1 1110

3.3V

3.3V

Gro

und

+5V

Gro

und

+5V

Gro

und

PW-O

K5V

SB+

5V

3.3V

-12V

Gro

und

PS-O

NG

roun

dG

roun

dG

roun

d-5

V+

5V

2 0

57


Front Panel Connectors

HDD-LED - HDD LEDThis LED will light when the hard drive is being accessed.

RESET SW - Reset SwitchThis switch allows you to reboot without having to power off thesystem.

PWR-BTN - Power SwitchThis switch is used to power on or off the system.

PWR-LED - Power/Standby LEDWhen the system’s power is on, this LED will light. When the systemis in the S1 (POS - Power On Suspend) state, it will blink everysecond. When the system is in the S3 (STR - Suspend To RAM)state, it will blink every 4 seconds.

Pin

1

35

79

11

N. C.

HDD-LED

RESET SW

N. C.

Pin Assignment

N. C.

HDD PowerSignal

GroundRST Signal

N. C.

Pin

246

810

12

PWR-LED

PWR-BTN

Key

Pin Assignment

LED PowerLED PowerSignal

PWR-BTN PowerSignal

Key

12

1112

HDD-LEDRESET SW

PWR-LEDPWR-BTN

58

3 BIOS Setup

Award BIOS Setup Utility

The Basic Input/Output System (BIOS) is a program that takes careof the basic level of communication between the processor andperipherals. In addition, the BIOS also contains codes for variousadvanced features found in this system board. This chapter explainsthe Setup Utility for the Award BIOS.

After you power up the system, the BIOS message appears on thescreen and the memory count begins. After the memory test, thefollowing message will appear on the screen:

Press DEL to enter setup

If the message disappears before you respond, restart the system orpress the “Reset” button. You may also restart the system bypressing the <Ctrl> <Alt> and <Del> keys simultaneously.

When you press <Del>, the main menu screen will appear.

Chapter 3 - BIOS Setup

59

3BIOS Setup

The settings on the screen are for reference only. Your version may not be identicalto this one.

Date

The date format is <day>, <month>, <date>, <year>. Day displaysa day, from Sunday to Saturday. Month displays the month, fromJanuary to December. Date displays the date, from 1 to 31. Yeardisplays the year, from 1990 to 2098.

Time

The time format is <hour>, <minute>, <second>. The time is basedon the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.Hour displays hours from 00 to 23. Minute displays minutes from00 to 59. Second displays seconds from 00 to 59.

Standard CMOS Features

Use the arrow keys to highlight “Standard CMOS Features” andpress <Enter>. A screen similar to the one below will appear.

60

3 BIOS Setup


IDE HDD Auto Detection

Detects the parameters of the drive. The parameters will automati-cally be shown on the screen.

IDE Channel 0 Master/Slave and IDE Channel 1 Master/Slave

The drive type information should be included in the documentationfrom your hard disk vendor. If you select ”Auto”, the BIOS will auto-detect the HDD & CD-ROM drive at the POST stage and showthe IDE for the HDD & CD-ROM drive. If a hard disk has notbeen installed, select “None”.

IDE Channel 0 Master/Slave and IDE Channel 1 Master/Slave

Move the cursor to the “IDE Channel 0 Master”, “IDE Channel 0Slave”, “IDE Channel 1 Master” or “IDE Channel 1 Slave” field, thenpress <Enter>.

61

3BIOS Setup

Access Mode

For hard drives larger than 528MB, you would typically select theLBA type. Certain operating systems require that you select CHS orLarge. Please check your operating system’s manual or Help desk onwhich one to select.

Capacity

Displays the approximate capacity of the disk drive. Usually the sizeis slightly greater than the size of a formatted disk given by a diskchecking program.

Cylinder

This field displays the number of cylinders.

Head

This field displays the number of read/write heads.

Precomp

This field displays the number of cylinders at which to change thewrite timing.

Landing Zone

This field displays the number of cylinders specified as the landingzone for the read/write heads.

Sector

This field displays the number sectors per track.

Drive A

This field identifies the type of floppy disk drive installed.

None No floppy drive is installed360K, 5.25 in. 5-1/4 in. standard drive; 360KB capacity1.2M, 5.25 in. 5-1/4 in. AT-type high-density drive; 1.2MB capacity720K, 3.5 in. 3-1/2 in. double-sided drive; 720KB capacity1.44M, 3.5 in. 3-1/2 in. double-sided drive; 1.44MB capacity2.88M, 3.5 in. 3-1/2 in. double-sided drive; 2.88MB capacity

62

3 BIOS Setup

Video

This field selects the type of video adapter used for the primarysystem monitor. Although secondary monitors are supported, you donot have to select the type. The default setting is EGA/VGA.

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. ForEGA, VGA, SVGA and PGA monitor adapters.

CGA 40 Color Graphics Adapter. Power up in 40-columnmode.

CGA 80 Color Graphics Adapter. Power up in 80-columnmode.

Mono Monochrome adapter. Includes high resolution mono-chrome adapters.

Halt On

This field determines whether the system will stop if an error isdetected during power up. The default setting is All Errors.

No Errors The system boot will not stop for any errors detected.All Errors The system boot will stop whenever the BIOS detects

a non-fatal error.All, But Keyboard The system boot will not stop for a keyboard

error; it will stop for all other errors.All, But Diskette The system boot will not stop for a disk error;

it will stop for all other errors.All, But Disk/Key The system boot will not stop for a disk or

keyboard error; it will stop for all other errors.

Base Memory

Displays the amount of base (or conventional) memory installed inthe system. The value of the base memory is typically 512K forsystems with 512K memory installed on the motherboard or 640Kfor systems with 640K or more memory installed on themotherboard.

63

3BIOS Setup

Extended Memory

Displays the amount of extended memory detected during boot-up.

Total Memory

Displays the total memory available in the system.

64

3 BIOS Setup

Advanced BIOS Features

The Advanced BIOS Features allows you to configure your systemfor basic operation. Some entries are defaults required by the systemboard, while others, if enabled, will improve the performance of yoursystem or let you set some features according to your preference.

The screen above list all the fields available in the Advanced BIOS Featuressubmenu, for ease of reference in this manual. In the actual CMOS setup, you haveto use the scroll bar to view the fields. The settings on the screen are for referenceonly. Your version may not be identical to this one.

65

3BIOS Setup

CPU Feature

Move the cursor to this field and press <Enter>. The followingscreen will appear.


Delay Prior To Thermal

This field is used to select the time that would force the CPU to a50% duty cycle when it exceeds its maximum operating temperaturetherefore protecting the CPU and the system board fromoverheating to ensure a safe computing environment..

Thermal Management

Select a “thermal monitor” in this field to enable the CPU’sspeedstep function. Restart the system then go to the operatingsystem’s “Control Panel”. Double-click “Power Options”. The “PowerOptions Properties” dialog box will appear. In the “Power Schemes”menu, select “Por table/Laptop”. Speedstep reduces the CPU’sfrequency and voltage in accordance to its load.

Thermal Monitor 1 On die throtting.Thermal Monitor 2 Ratio and VID transition.

TM2 Bus Ratio

This field is used to select the frequency (bus ratio) of the throttledperformance state that will be initiated when the on-die sensor turnsfrom cool to hot.

66

3 BIOS Setup

TM2 Bus VID

This field is used to select the voltage of the throttled performancestate that will be initiated when the on-die sensor turns from cool tohot.

Execute Disable Bit

When this field is set to Disabled, it will force the XD feature flag toalways return to 0.

Hard Disk Boot Priority

This field is used to select the boot sequence of the hard drives.Move the cursor to this field then press <Enter>. Use the Up orDown arrow keys to select a device then press <+> to move it upor <-> to move it down the list.


67

3BIOS Setup

CPU L1 & L2 Cache

These fields speed up the memory access. The default value isenabled. Enable the external cache for better performance.

CPU L3 Cache

This field is used to enable or disable the CPU’s L3 cache.

Quick Power On Self Test

This field speeds up Power On Self Test (POST) whenever thesystem is powered on. The BIOS will shorten or skip some checkitems during POST. To attain the shortest POST time, select “Fast”.

First Boot Device, Second Boot Device, Third Boot Device and BootOther Device

Select the drive to boot first, second and third in the “First BootDevice” “Second Boot Device” and “Third Boot Device” fieldsrespectively. The BIOS will boot the operating system according tothe sequence of the drive selected. Set “Boot Other Device” toEnabled if you wish to boot from another device.

Boot Up Floppy Seek

When enabled, the BIOS will check whether the floppy disk driveinstalled is 40 or 80 tracks. Note that the BIOS cannot distinguishbetween 720K, 1.2M, 1.44M and 2.88M drive types as they are all 80tracks. When disabled, the BIOS will not search for the type of floppydisk drive by track number. Note that there will not be any warningmessage if the drive installed is 360KB.

Boot Up NumLock Status

This allows you to determine the default state of the numerickeypad. By default, the system boots up with NumLock on whereinthe function of the numeric keypad is the number keys. When set toOff, the function of the numeric keypad is the arrow keys.

68

3 BIOS Setup

Gate A20 Option

This entry allows you to select how gate A20 is handled. Gate A20is a device used to address memory above 1 Mbyte. Initially, gate A20was handled via the keyboard controller. Today, while keyboards stillprovide this support, it is more common, and much faster, for thesystem chipset to provide support for gate A20.

Fast The chipset controls Gate A20.Normal A pin in the keyboard controller controls Gate A20.

Typematic Rate Setting

Disabled Continually holding down a key on your keyboard willcause the BIOS to report that the key is down.

Enabled The BIOS will not only report that the key is down,but will first wait for a moment, and, if the key is stilldown, it will begin to report that the key has beendepressed repeatedly. For example, you would use sucha feature to accelerate cursor movements with thearrow keys. You can then select the typematic rate andtypematic delay in the “Typematic Rate (Chars/Sec)”and “Typematic Delay (Msec)” fields below.

Typematic Rate (Chars/Sec)

This field allows you to select the rate at which the keys areaccelerated.

Typematic Delay (Msec)

This field allows you to select the delay between when the key wasfirst depressed and when the acceleration begins.

69

3BIOS Setup

Security Option

This field determines when the system will prompt for the password- everytime the system boots or only when you enter the BIOSsetup. Set the password in the Set Supervisor/User Passwordsubmenu.

System The system will not boot and access to Setup will bedenied unless the correct password is entered at theprompt.

Setup The system will boot, but access to Setup will be deniedunless the correct password is entered at the prompt.

APIC Mode

Leave this field in its default setting.

MPS Version Control for OS

This field is used to select the MPS version that the system board isusing.

OS Select for DRAM > 64MB

This field allows you to access the memory that is over 64MB inOS/2.

Report No FDD For WIN 95

The options are Yes and No.

Small Logo(EPA) Show

Enabled The EPA logo will appear during system boot-up.Disabled The EPA logo will not appear during system boot-up.

70

3 BIOS Setup

Advanced Chipset Features

This section gives you functions to configure the system based onthe specific features of the chipset. The chipset manages bus speedsand access to system memory resources. These items should notbe altered unless necessary. The default settings have been chosenbecause they provide the best operating conditions for your system.The only time you might consider making any changes would be ifyou discovered some incompatibility or that data was being lostwhile using your system.

DRAM Timing Selectable

This field is used to select the timing of the DRAM.

By SPD The EEPROM on a DIMM has SPD (Serial Pres-ence Detect) data structure that stores informationabout the module such as the memory type,memory size, memory speed, etc. When this optionis selected, the system will run according to theinformation in the EEPROM. This option is thedefault setting because it provides the most stablecondition for the system. The “CAS Latency Time”to “System Memory Frequency” fields will show thedefault settings by SPD.

Manual If you want better performance for your systemother than the one “by SPD”, select “Manual” then

The screen above list all the fields available in the Advanced Chipset Featuressubmenu, for ease of reference in this manual. In the actual CMOS setup, you haveto use the scroll bar to view the fields. The settings on the screen are for referenceonly. Your version may not be identical to this one.

71

3BIOS Setup

select the best option in the “CAS Latency Time”to “System Memory Frequency” fields.

CAS Latency Time

This field is used to select the latency between the DRAM readcommand and the time that the data was received.

DRAM RAS# to CAS# Delay

This field is used to select the latency between the DRAM activecommand and the read/write command.

DRAM RAS# Precharge

This field is used to select the idle clocks after issuing a prechargecommand to the DRAM.

Precharge Delay (tRAS)

The options are Auto, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 and 15.

System Memory Frequency

This field is used to select the memory clock speed of the DIMM.

System BIOS Cacheable

When this field is enabled, accesses to the system BIOS ROMaddressed at F0000H-FFFFFH are cached, provided that the cachecontroller is enabled. The larger the range of the Cache RAM, thehigher the efficiency of the system.

Video BIOS Cacheable

As with caching the system BIOS, enabling the Video BIOS cache willallow access to video BIOS addresssed at C0000H to C7FFFH tobe cached, if the cache controller is also enabled. The larger the rangeof the Cache RAM, the faster the video performance.

72

3 BIOS Setup

Memory Hole At 15M-16M

In order to improve system performance, certain space in memory canbe reserved for ISA cards. This memory must be mapped into thememory space below 16MB. When enabled, the CPU assumes the 15-16MB memory range is allocated to the hidden ISA address rangeinstead of the actual system DRAM. When disabled, the CPU assumesthe 15-16MB address range actually contains DRAM memory. If morethan 16MB of system memory is installed, this field must be disabledto provide contiguous system memory.

On-Chip Frame Buffer Size

This field is used to select the onboard VGA’s frame buffer size thatis shared from the system memory.

DVMT Mode

This field shows the current DVMT mode.

DVMT/Fixed Memory Size

This field is used to select the graphics memory size used by DVMT/Fixed mode.

73

3BIOS Setup

Panel Number

If you are using one of the standard panels shown below, select theappropriate option according to the type of panel that you are using.Otherwise, please contact your dealer or sales representative for acustom-made BIOS that will suit the panel that you are using.

Panel 1 640x480, one channel 18-bit, LVDSPanel 2 800x600, one channel 18-bit, LVDSPanel 3 1024x768, one channel 18-bit, LVDSPanel 4 1280x1024, two channel 36-bit, LVDSPanel 5 to Panel 16 Reserved

74

3 BIOS Setup

Integrated Peripherals


OnChip IDE Device



75

3BIOS Setup

IDE HDD Block Mode

Enabled The IDE HDD uses the block mode. The systemBIOS will check the hard disk drive for the maxi-mum block size the system can transfer. The blocksize will depend on the type of hard disk drive.

Disabled The IDE HDD uses the standard mode.

IDE DMA Transfer Access

This field, when Enabled, will enhance the IDE DMA transfer of anIDE hard disk drive.

On-Chip Primary PCI IDE

These fields allow you to enable or disable the primary and second-ary IDE controller. Select Disabled if you want to add a differenthard drive controller.

IDE Primary Master PIO and IDE Primary Slave PIO

PIO means Programmed Input/Output. Rather than have the BIOSissue a series of commands to effect a transfer to or from the diskdrive, PIO allows the BIOS to tell the controller what it wants andthen let the controller and the CPU perform the complete task bythemselves. Your system supports five modes, 0 (default) to 4, whichprimarily differ in timing. When Auto is selected, the BIOS will selectthe best available mode after checking your drive.

Auto The BIOS will automatically set the system accordingto your hard disk drive’s timing.

Mode 0-4 You can select a mode that matches your hard diskdrive’s timing. Caution: Do not use the wrong settingor you will have drive errors.

IDE Primary Master UDMA and IDE Primary Slave UDMA

These fields allow you to set the Ultra DMA in use. When Auto isselected, the BIOS will select the best available option after checkingyour hard drive or CD-ROM.

Auto The BIOS will automatically detect the settings foryou.

Disabled The BIOS will not detect these categories.

76

3 BIOS Setup

On-Chip Serial ATA Setting

On-Chip Serial ATA

Disabled Disables the onboard SATA.Auto The system will detect the existing SATA and

IDE drives then automatically set them to theavailable master/slave mode.

Combined Mode This option allows you to use both IDE andSATA drives; allowing a maximum of 4 drives -1 IDE Master, 1 IDE Slave and 2 SATA;supporting maximum of 2 drives on eachchannel.

Enhanced Mode This option allows you to use both IDE andSATA drives; allowing a maximum of 4 drives -1 IDE Master, 1 IDE Slave and 2 SATA.

SATA Only This option automatically sets the SATA drivesto Primary Master mode. Since the SATAdrives are in Master mode, you cannot set theIDE drive to Master mode.

PATA IDE Mode

This field is used to select the function mode of the IDEconnector.

Primary IDE serves as Primary Master and PrimarySlave channel. SATA 1 and SATA 2 serve asSecondary Master and Secondary Slave channel.

Secondary IDE ser ves as Secondar y Master andSecondary Slave channel. SATA 1 and SATA 2serve as Primary Master and Primary Slavechannel.

77

3BIOS Setup

Onboard Device



USB Controller

Enabled Enables the onboard USB.Disabled Disables the onboard USB.

USB 2.0 Controller

If you are using a USB 2.0 device, this field must be set to Enabled.

USB Keyboard Support

By default, this field is Disabled. However, if you are using a USBkeyboard under DOS, make sure to enable this function.

78

3 BIOS Setup

AC97 Audio

Auto Select this option when using the onboard audioCODEC.

Disabled Select this option when using a PCI sound card.

Onboard LAN Control

This field is used to enable or disable the onboard LAN.

79

3BIOS Setup

Super IO Device



Power On Function

This field allows you to use the keyboard or PS/2 mouse to power-on the system.

Button only Default setting. Uses the power button to poweron the system.

Password When this option is selected, set the password youwould like to use to power-on the system in the“KB Power On Password” field.

Hot Key When this option is selected, select the function keyyou would like to use to power-on the system inthe “Hot Key Power On” field.

Mouse Left When this option is selected, double-click the leftbutton of the mouse to power-on the system.

Mouse Right When this option is selected, double-click the rightbutton of the mouse to power-on the system.

Any Key Press any key to power-on the system.Keyboard 98 When this option is selected, press the “wake up”

key of the Windows® 98 compatible keyboard topower-on the system.

80

3 BIOS Setup

KB Power On Password

Move the cursor to this field and press <Enter>. Enter your pass-word. You can enter up to 5 characters. Type in exactly the samepassword to confirm, then press <Enter>.

The power button will not function once a keyboard password hasbeen set in this field. You must type the correct password to power-on the system. If you forgot the password, power-off the system andremove the battery. Wait for a few seconds and install it backbefore powering-on the system.

Hot Key Power On

This field is used to select a function key that you would like to useto power-on the system.

Onboard FDC Controller

Enabled Enables the onboard floppy disk controller.Disabled Disables the onboard floppy disk controller.

PWRON After PWR-Fail

Off When power returns after an AC power failure, thesystem’s power is off. You must press the Powerbutton to power-on the system.

On When power returns after an AC power failure, thesystem will automatically power-on.

Former-Sts When power returns after an AC power failure, thesystem will return to the state where you left offbefore power failure occurs. If the system’s power isoff when AC power failure occurs, it will remain offwhen power returns. If the system’s power is onwhen AC power failure occurs, the system will power-on when power returns.

81

3BIOS Setup

Serial Port 1 Mode

COM 1 functions as a serial port or IrDA. You cannot use both atthe same time.

Normal This option sets COM 1 as serial port.IrDA This option sets COM 1 as IrDA.

IRDA Duplex Mode

Half Data is completely transmitted before receiving data.Full Transmits and receives data simultaneously.

Onboard Serial Port 1 and Onboard Serial Port 2

Auto The system will automatically select an I/O address forthe onboard serial port 1 and serial port 2.

3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3 Allows you to manu-ally select an I/O address for the onboard serial port 1and serial port 2.

Disabled Disables the onboard serial port 1 and/or serial port 2.

Onboard Serial Port 3

This is used to select an I/O address for the onboard serial port 3.However, if the LCD Display Panel supports touch screen, leave thisfield in its default setting because the touch screen is internallyconnected to COM 3 therefore a default address has already beenassigned to this port. Make sure COM 3 is not attached with aserial device.

Onboard Serial Port 4

This is used to select an I/O address for the onboard serial port 4.

Serial Port 1 Use IRQ, Serial Port 2 Use IRQ, Serial Port 3 Use IRQand Serial Port 4 Use IRQ

These fields are used to select an IRQ for the onboard serial port 1,2, 3 or 4.

82

3 BIOS Setup

Power Management Setup

The Power Management Setup allows you to configure your systemto most effectively save energy.

ACPI Function

This function should be enabled only in operating systems that sup-port ACPI. Currently, only Windows®®®®® 2000/ME/XP supports thisfunction. If you want to use the Suspend to RAM function, make surethis field is enabled then select “S3(STR)” in the “ACPI Suspend Type”field.

ACPI Suspend Type

This field is used to select the type of Suspend mode.

S1(POS) Enables the Power On Suspend function.S3(STR) Enables the Suspend to RAM function.

Run VGABIOS if S3 Resume

When this field is set to Auto, the system will initialize the VGA BIOSwhen it wakes up from the S3 state. This can be configured only ifthe “ACPI Suspend Type” field is set to “S3(STR)”.


83

3BIOS Setup

Power Management

This field allows you to select the type (or degree) of power savingby changing the length of idle time that elapses before the Suspendmode and HDD Power Down fields are activated.

Min Saving Minimum power saving time for the Suspend Mode(1 hour) and HDD Power Down (15 min.)

Max Saving Maximum power saving time for the. SuspendMode and HDD Power Down = 1 min.

User Define Allows you to set the power saving time in the“Suspend Mode” and “HDD Power Down” fields.

Video Off Method

This determines the manner in which the monitor is blanked.

V/H SYNC + Blank This selection will cause the system to turnoff the vertical and horizontal synchronizationports and write blanks to the video buffer.

Blank Screen This option only writes blanks to the video buffer.DPMS Initializes display power management signaling. Use

this option if your video board supports it.

Video Off In Suspend

This field is used to activate the video off feature when the systementers the Suspend mode. The options are Yes and No.

Suspend Type

The options are Stop Grant and PwrOn Suspend.

MODEM Use IRQ

This field is used to set an IRQ channel for the modem installed inyour system.

84

3 BIOS Setup

Suspend Mode

This is selectable only when the Power Management field is set toUser Define. When the system enters the Suspend mode accordingto the power saving time selected, the CPU and onboardperipherals will be shut off.

HDD Power Down

This is selectable only when the Power Management field is set toUser Define. When the system enters the HDD Power Down modeaccording to the power saving time selected, the hard disk drive willbe powered down while all other devices remain active.

Soft-Off by PWR-BTTN

This field allows you to select the method of powering off yoursystem.

Delay 4 Sec. Regardless of whether the Power Management func-tion is enabled or disabled, if the power button ispushed and released in less than 4 sec, the systementers the Suspend mode. The purpose of thisfunction is to prevent the system from powering offin case you accidentally “hit” or pushed the powerbutton. Push and release again in less than 4 sec torestore. Pushing the power button for more than 4seconds will power off the system.

Instant-Off Pressing and then releasing the power button atonce will immediately power off your system.

CPU THRM-Throttling

Thermal throttling regulates the thermal environment by alternatingbetween running the processor at full speed and placing the processorin a sleep state whenever the upper limits of the thermal envelop arereached.

85

3BIOS Setup

Wake-Up By PCI Card

Enabled This field should be set to Enabled only if your PCIcard such as LAN card or modem card uses the PCIPME (Power Management Event) signal to remotelywake up the system. Access to the LAN card or PCIcard will cause the system to wake up. Refer to thecard’s documentation for more information.

Disabled The system will not wake up despite access to the PCIcard.

Power On By Ring

Set this field to Enabled to use the modem ring-on function. This willallow your system to power-on to respond to calls coming from anexternal modem.

USB KB Wake-Up From S3

This field, when enabled, allows you to use a USB keyboard to wakeup a system that is in the S3 (STR - Suspend To RAM) state. Thiscan be configured only if the “ACPI Suspend Type” field is set to“S3(STR)”.

Resume By Alarm

Enabled When Enabled, you can set the date and time youwould like the Soft Power Down (Soft-Off) PC topower-on in the “Date (of Month) Alarm” and “Time(hh:mm:ss) Alarm” fields. However, if the system is beingaccessed by incoming calls or the network (Resume OnRing/LAN) prior to the date and time set in thesefields, the system will give priority to the incoming callsor network.

Disabled Disables the automatic power-on function. (default)

Date (of Month) Alarm

0 The system will power-on everyday according to thetime set in the “Time (hh:mm:ss) Alarm” field.

1-31 Select a date you would like the system to power-on.The system will power-on on the set date, and time setin the “Time (hh:mm:ss) Alarm” field.

86

3 BIOS Setup

Time (hh:mm:ss) Alarm

This is used to set the time you would like the system to power-on.If you want the system to power-on everyday as set in the “Date(of Month) Alarm” field, the time set in this field must be later thanthe time of the RTC set in the Standard CMOS Features submenu.

87

3BIOS Setup

Init Display First

This field is used to select whether to initialize the onboard VGA,PCI Express or PCI first when the system boots.

Onboard When the system boots, it will first initialize theonboard VGA.

PCIEx When the system boots, it will first initialize the PCIExpress x16 graphics card.

PCI Slot When the system boots, it will first initialize PCI.

Reset Configuration Data

Enabled The BIOS will reset the Extended System ConfigurationData (ESCD) once automatically. It will then recreate anew set of configuration data.

Disabled The BIOS will not reset the configuration data.

PnP/PCI Configurations

This section describes configuring the PCI bus system. It coverssome very technical items and it is strongly recommended that onlyexperienced users should make any changes to the default settings.


88

3 BIOS Setup

Resources Controlled By

The Award Plug and Play BIOS has the capability to automaticallyconfigure all of the boot and Plug and Play compatible devices.

Auto The system will automatically detect the settings for you.Manual Choose the specific IRQ in the “IRQ Resources” field

respectively.

IRQ Resources

Move the cursor to this field and press <Enter>. This field is used toset each system interrupt to either Reserved or PCI Device.

PCI/VGA Palette Snoop

This field determines whether the MPEG ISA/VESA VGA cards canwork with PCI/VGA or not. The default value is Disabled.

Enabled MPEG ISA/VESA VGA cards work with PCI/VGA.Disabled MPEG ISA/VESA VGA cards does not work with PCI/

VGA.

Maximum Payload Size

This field is used to select the maximum TLP payload size of the PCIExpress devices. The unit is byte.


89

3BIOS Setup

PC Health Status

Current System Temp., Current CPU Temperature, Current System FanSpeed, Current CPU Fan Speed and Current 2nd Fan Speed

These fields will show the internal temperature of the system, currenttemperature of the CPU, and the current fan speed of the cooling fansin RPM (Revolutions Per Minute).

CPU(V)

This field shows the detected voltage of the processor.

+1.5V, +3.3V, +5V, +12V, -12V, VBAT(V) and 5VSB(V)

These fields show the output voltage of the power supply.

Note:The onboard hardware monitor function is capable of detecting“system health” conditions but if you want a warning messageto pop-up or a warning alarm to sound when an abnormalcondition occurs, you must install the Hardware Monitor forWindows utility. This utility is included in the CD that came withthe system board. Refer to the Hardware Monitor for Windowssection in chapter 4 for more information.


90

3 BIOS Setup

Frequency/Voltage Control


Auto Detect PCI Clk

When enabled, the system will automatically send clock signals toexisting PCI devices.

Spread Spectrum

Leave this field in its default setting. Do not alter this setting unlessadvised by an engineer or technician.

91

3BIOS Setup

Load Fail-Safe Defaults

The “Load Fail-Safe Defaults” option loads the troubleshootingdefault values permanently stored in the ROM chips. These settingsare not optimal and turn off all high performance features. Youshould use these values only if you have hardware problems.Highlight this option in the main menu and press <Enter>.

If you want to proceed, type <Y> and press <Enter>. The defaultsettings will be loaded.

92

3 BIOS Setup

Load Optimized Defaults

The “Load Optimized Defaults” option loads optimized settings fromthe BIOS ROM. Use the default values as standard values for yoursystem. Highlight this option in the main menu and press <Enter>.

Type <Y> and press <Enter> to load the Setup default values.

93

3BIOS Setup

Set Supervisor Password

If you want to protect your system and setup from unauthorizedentry, set a supervisor’s password with the “System” option selectedin the Advanced BIOS Features. If you want to protect access tosetup only, but not your system, set a supervisor’s password with the“Setup” option selected in the Advanced BIOS Features. You will notbe prompted for a password when you cold boot the system.

Use the arrow keys to highlight “Set Supervisor Password” andpress <Enter>.

Type in the password. You are limited to eight characters. Whendone, the message below will appear:

Confirm Password:

You are asked to verify the password. Type in exactly the samepassword. If you type in a wrong password, you will be promptedto enter the correct password again. To delete or disable thepassword function, highlight “Set Supervisor Password” and press<Enter>, instead of typing in a new password. Press the <Esc> keyto return to the main menu.

94

3 BIOS Setup

Set User Password

If you want another user to have access only to your system butnot to setup, set a user’s password with the “System” option se-lected in the Advanced BIOS Features. If you want a user to enter apassword when trying to access setup, set a user’s password withthe “Setup” option selected in the Advanced BIOS Features.

Using user’s password to enter Setup allows a user to access only“Set User Password” that appears in the main menu screen. Accessto all other options is denied.

Use the arrow keys to highlight “Set User Password” and press<Enter>.

Type in the password. You are limited to eight characters. Whendone, the message below will appear:

Confirm Password:

You are asked to verify the password. Type in exactly the samepassword. If you type in a wrong password, you will be promptedto enter the correct password again. To delete or disable thepassword function, highlight “Set User Password” and press <Enter>,instead of typing in a new password. Press the <Esc> key to returnto the main menu.

95

3BIOS Setup

Save & Exit Setup

When all the changes have been made, highlight “Save & Exit Setup”and press <Enter>.

Type “Y” and press <Enter>. The modifications you have made willbe written into the CMOS memory, and the system will reboot. Youwill once again see the initial diagnostics on the screen. If you wish tomake additional changes to the setup, press <Ctrl> <Alt> <Esc>simultaneously or <Del> after memory testing is done.

96

3 BIOS Setup

Exit Without Saving

When you do not want to save the changes you have made,highlight “Exit Without Saving” and press <Enter>.

Type “Y” and press <Enter>. The system will reboot and you willonce again see the initial diagnostics on the screen. If you wish tomake any changes to the setup, press <Ctrl> <Alt> <Esc> simulta-neously or <Del> after memory testing is done.

97

3BIOS Setup

Updating the BIOS

To update the BIOS, you will need the new BIOS file and a flashutility, AWDFLASH.EXE. Please contact technical support or yoursales representative for the files.

1. Save the new BIOS fi le along with the flash uti l ityAWDFLASH.EXE to a floppy disk.

2. Reboot the system and enter the Award BIOS Setup Utility toset the first boot drive to “Floppy”.

3. Save the setting and reboot the system.

4. After the system booted from the floppy disk, execute the flashutility by typing AWDFLASH.EXE. The following screen will appear.

5. Type the new BIOS file name onto the gray area that is next to“File Name to Program” then press <Enter>.

Award BIOS Flash Utility V.8.15B(C) Phoenix Technologies Ltd. All Rights Reserved.

(The current BIOS information will appear in this area.)

File Name to Program :

98

3 BIOS Setup

6. The following will appear.

Do You Want to Save BIOS (Y/N)

This question refers to the current existing BIOS in your system.We recommend that you save the current BIOS and its flashutility; just in case you need to reinstall the BIOS. To save thecurrent BIOS, press <Y> then enter the file name of the currentBIOS. Otherwise, press <N>.

7. The following will then appear.

Press “Y” to Program or “N” to Exit

8. Press <Y> to flash the new BIOS.

99

4Supported Software

Chapter 4 - Supported Software

Drivers, Utilities and Software Applications

The CD that came with the system board contains drivers, utilitiesand software applications required to enhance the performance ofthe system board.

Insert the CD into a CD-ROM drive. The autorun screen (MainBoard Utility CD) will appear. If after inserting the CD, "Autorun" didnot automatically start (which is, the Mainboard Utility CD screen didnot appear), please go directly to the root directory of the CD anddouble-click "Setup".

100

4 Supported Software

Intel Chipset Software Installation Utility

The Intel Chipset Software Installation Utility is used for updatingWindows® INF files so that the Intel chipset can be recognized andconfigured properly in the system.

To install the utility, please follow the steps below.

1. Click “Intel Chipset Software Installation Utility” on the mainmenu. The following screen will appear.

2. Follow the prompts on the screen to complete installation.

3. Reboot the system for the utility to take effect.

101

4Supported Software

Intel Graphics Drivers

To install the driver, please follow the steps below.

1. Click “Intel Graphics Drivers” on the main menu. The followingscreen will appear.


3. Reboot the system for the driver to take effect.

102


Audio Drivers


1. Click “Audio Drivers” on the main menu. The following screen willappear.



103

4Supported Software

LAN Drivers


1. Click “LAN Drivers” on the main menu. The following screen willappear.



104


Hardware Monitor for Windows

Hardware Monitor for Windows is capable of monitoring thesystem’s hardware conditions such as the temperature of the CPUand system, voltage, and speed of the cooling fans. It also allows youto manually set a range to the items being monitored. If the valuesare over or under the set range, a warning message will pop-up. Theutility can also be configured so that a beeping alarm will soundwhenever an error occurs. We recommend that you use the “DefaultSetting” which is the ideal setting that would keep the system ingood working condition.

To install the utility, please follow the steps below.

1. Click “Hardware Monitor for Windows” on the main menu. Thescreen below will appear.


3. Restart the system.

105

4Supported Software

Microsoft DirectX 9.0C Driver

To install, please follow the steps below.

1. Click “Microsoft DirectX 9.0C Driver” on the main menu. Thefollowing screen will appear.

2. Click “I accept the agreement” then click “Next”.



106


Intel USB 2.0 Drivers

The Intel chipset does not support USB 2.0 drivers for Windows®

98 SE and Windows® ME.

Windows® XP

If your Windows® XP CD already includes Service Pack 1, the USB2.0 driver will automatically install when you install the operatingsystem. If the CD does not include Service Pack 1, it is available fordownload at Microsoft’s Windows Update website.

Windows® 2000

If your Windows® 2000 CD already includes Service Pack 4, theUSB 2.0 driver will automatically install when you install the operatingsystem. If the CD does not include Service Pack 4, it is available fordownload at Microsoft’s Windows Update website.

Installation Notes

1. "Autorun" ONLY supports the Windows® 98 SE, Windows® ME,Windows® 2000, Windows NT® 4.0 and Windows® XPoperating systems. If after inserting the CD, "Autorun" did notautomatically start (which is, the Main Board Utility CD screendid not appear), please go directly to the root directory of theCD and double-click "Setup".

2. All steps or procedures to install software drivers are subject tochange without notice as the softwares are occassionally updated.Please contact technical support or your sales representative forthe latest version of the drivers or software applications.

107

AWatchdog Timer

Appendix A - Watchdog Timer

Watchdog Timer

The following parameters are references for setting the time intervalof the Watchdog Timer function. The system will regularly be “cleared”according to the set time interval. If the system hangs or fails tofunction, it will also reset according to the time interval so that yoursystem will continue to operate.

mov dx,04e <Enter>mov al,87 <Enter>out dx,al <Enter>out dx,al <Enter>mov dx,04e <Enter>mov al,07 <Enter>out dx,al <Enter>inc dx <Enter>inc al <Enter>out dx,al <Enter>dec dx <Enter>mov al,f6 <Enter>out dx,al <Enter>inc dx <Enter>mov al,xy <Enter>out dx,al <Enter>

“XY” is the Watchdog Time count value for the “00h to “FFh” rangewherein the time can be set from 0 sec. to 255 sec.

B

108

System Error Message

When the BIOS encounters an error that requires the user tocorrect something, either a beep code will sound or a message willbe displayed in a box in the middle of the screen and the message,PRESS F1 TO CONTINUE or DEL TO ENTER SETUP, will be shownin the information box at the bottom. Enter Setup to correct theerror.

POST Beep

There are two kinds of beep codes in the BIOS. One code indicatesthat a video error has occured and the BIOS cannot initialize thevideo screen to display any additional information. This beep codeconsists of a single long beep followed by three short beeps. Theother code indicates that a DRAM error has occured. This beepcode consists of a single long beep.

Error Messages

One or more of the following messages may be displayed if theBIOS detects an error during the POST. This list indicates the errormessages for all Awards BIOSes:

CMOS BATTERY HAS FAILEDThe CMOS battery is no longer functional. It should be replaced.

Caution:Danger of explosion if battery incorrectly replaced. Replace onlywith the same or equivalent type recommended by themanufacturer. Dispose of used batteries according to thebattery manufacturer’s instructions.

CMOS CHECKSUM ERRORChecksum of CMOS is incorrect. This can indicate that CMOS hasbecome corrupt. This error may have been caused by a weakbattery. Check the battery and replace if necessary.

DISPLAY SWITCH IS SET INCORRECTLYThe display switch on the motherboard can be set to eithermonochrome or color. This indicates the switch is set to a different

Appendix B - System Error Message

BSystem Error Message

109

setting than indicated in Setup. Determine which setting is correct,either turn off the system and change the jumper or enter Setup andchange the VIDEO selection.

FLOPPY DISK(S) fail (80)Unable to reset floppy subsystem.

FLOPPY DISK(S) fail (40)Floppy type mismatch.

Hard Disk(s) fail (80)HDD reset failed.

Hard Disk(s) fail (40)HDD controller diagnostics failed.

Hard Disk(s) fail (20)HDD initialization error.

Hard Disk(s) fail (10)Unable to recalibrate fixed disk.

Hard Disk(s) fail (08)Sector Verify failed.

Keyboard is locked out - Unlock the keyThe BIOS detects that the keyboard is locked. Keyboard controller ispulled low.

Keyboard error or no keyboard presentCannot initialize the keyboard. Make sure the keyboard is attachedcorrectly and no keys are being pressed during the boot.

Manufacturing POST loopSystem will repeat POST procedure infinitely while the keyboardcontroller is pull low. This is also used for the M/B burn in test at thefactory.

BIOS ROM checksum error - System haltedThe checksum of ROM address F0000H-FFFFFH is bad.

Memory test failThe BIOS reports memory test fail if the memory has error(s).

C

110

Troubleshooting

Troubleshooting Checklist

This chapter of the manual is designed to help you with problemsthat you may encounter with your personal computer. To efficientlytroubleshoot your system, treat each problem individually. This is toensure an accurate diagnosis of the problem in case a problem hasmultiple causes.

Some of the most common things to check when you encounterproblems while using your system are listed below.

1. The power switch of each peripheral device is turned on.2. All cables and power cords are tightly connected.3. The electrical outlet to which your peripheral devices are

connected is working. Test the outlet by plugging in a lamp orother electrical device.

4. The monitor is turned on.5. The display’s brightness and contrast controls are adjusted

properly.6. All add-in boards in the expansion slots are seated securely.7. Any add-in board you have installed is designed for your system

and is set up correctly.

Monitor/Display

If the display screen remains dark after the system is turned on:

1. Make sure that the monitor’s power switch is on.2. Check that one end of the monitor’s power cord is properly

attached to the monitor and the other end is plugged into aworking AC outlet. If necessary, try another outlet.

3. Check that the video input cable is properly attached to themonitor and the system’s display adapter.

4. Adjust the brightness of the display by turning the monitor’sbrightness control knob.

Appendix C - Troubleshooting

CTroubleshooting

111

The picture seems to be constantly moving.

1. The monitor has lost its vertical sync. Adjust the monitor’s verticalsync.

2. Move away any objects, such as another monitor or fan, thatmay be creating a magnetic field around the display.

3. Make sure your video card’s output frequencies are supportedby this monitor.

The screen seems to be constantly wavering.

1. If the monitor is close to another monitor, the adjacent monitormay need to be turned off. Fluorescent lights adjacent to themonitor may also cause screen wavering.

Power Supply

When the computer is turned on, nothing happens.

1. Check that one end of the AC power cord is plugged into a liveoutlet and the other end properly plugged into the back of thesystem.

2. Make sure that the voltage selection switch on the back panel isset for the correct type of voltage you are using.

3. The power cord may have a “short” or “open”. Inspect the cordand install a new one if necessary.

Floppy Drive

The computer cannot access the floppy drive.

1. The floppy diskette may not be formatted. Format the disketteand try again.

2. The diskette may be write-protected. Use a diskette that is notwrite-protected.

3. You may be writing to the wrong drive. Check the pathstatement to make sure you are writing to the targeted drive.

4. There is not enough space left on the diskette. Use anotherdiskette with adequate storage space.

C

112

Troubleshooting

Hard Drive

Hard disk failure.

1. Make sure the correct drive type for the hard disk drive hasbeen entered in the BIOS.

2. If the system is configured with two hard drives, make sure thebootable (first) hard drive is configured as Master and thesecond hard drive is configured as Slave. The master hard drivemust have an active/bootable partition.

Excessively long formatting period.

1. If your hard drive takes an excessively long period of time toformat, it is likely a cable connection problem. However, if yourhard drive has a large capacity, it will take a longer time toformat.

Serial Port

The serial device (modem, printer) doesn’t output anything or isoutputting garbled characters.

1. Make sure that the serial device’s power is turned on and thatthe device is on-line.

2. Verify that the device is plugged into the correct serial port onthe rear of the computer.

3. Verify that the attached serial device works by attaching it to aserial port that is working and configured correctly. If the serialdevice does not work, either the cable or the serial device has aproblem. If the serial device works, the problem may be due tothe onboard I/O or the address setting.

4. Make sure the COM settings and I/O address are configuredcorrectly.

CTroubleshooting

113

Keyboard

Nothing happens when a key on the keyboard was pressed.

1. Make sure the keyboard is properly connected.2. Make sure there are no objects resting on the keyboard and

that no keys are pressed during the booting process.

System Board

1. Make sure the add-in card is seated securely in the expansionslot. If the add-in card is loose, power off the system, re-installthe card and power up the system.

2. Check the jumper settings to ensure that the jumpers areproperly set.

3. Verify that all memory modules are seated securely into thememory sockets.

4. Make sure the memory modules are in the correct locations.5. If the board fails to function, place the board on a flat surface

and seat all socketed components. Gently press each componentinto the socket.

6. If you made changes to the BIOS settings, re-enter setup andload the BIOS defaults.

nb73 ea es rev A 58600213 1 - Daisy Data Displays

Documents