multifunctional materials of interests and their ... · Iqbal, H.M.N., Kyazze, G., Tron, T. and Keshavarz, T. This is a copy of an article published in Saudi Journal of Biological
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
aApplied Biotechnology Research Group, Department of Life Sciences, Faculty of Science and Technology, Universityof Westminster, London, United KingdombAix Marseille Universite, CNRS, Centrale Marseille, iSm2 UMR 7313, Marseille, France
Received 10 August 2015; revised 15 October 2015; accepted 15 January 2016
KEYWORDS
Biological polymers;
Composite materials;
Laccase;
Aspergillus niger
Abstract In the present study, we propose a green route to prepare poly(3-hydroxybutyrate)
[(P(3HB)] grafted ethyl cellulose (EC) based green composites with novel characteristics through
laccase-assisted grafting. P(3HB) was used as a side chain whereas, EC as a backbone material
under ambient processing conditions. A novel laccase obtained from Aspergillus niger through its
heterologous expression in Saccharomyces cerevisiae was used as a green catalyst for grafting pur-
poses without the use of additional initiator and/or cross-linking agents. Subsequently, the resulting
P(3HB)-g-EC composites were characterized using a range of analytical and imagining techniques.
Fourier transform infrared spectroscopy (FT-IR) spectra showed an increase in the hydrogen-
bonding type interactions between the side chains of P(3HB) and backbone material of EC.
Evidently, X-ray diffraction (XRD) analysis revealed a decrease in the crystallinity of the
P(3HB)-g-EC composites as compared to the pristine individual polymers. A homogeneous
P(3HB) distribution was also achieved in case of the graft composite prepared in the presence of
2,20-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) as a mediator along with laccase
as compared to the composite prepared using pure laccase alone. A substantial improvement in
the thermal and mechanical characteristics was observed for grafted composites up to the different
extent as compared to the pristine counterparts. The hydrophobic/hydrophilic properties of the
grafted composites were better than those of the pristine counterparts.� 2016 The Authors. Production and hosting by Elsevier B.V. on behalf of King Saud University. This is
an open access article under the CCBY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
1. Introduction
From the last few years, bio-based bio-composite biomaterialsare being engineered for their prospective applications in dif-
ferent sectors of the modern world that includes bio- andnon-bio subdivisions, with an aim, to address a global
Peer review under responsibility of King Saud University.
Production and hosting by Elsevier
Saudi Journal of Biological Sciences (2016) xxx, xxx–xxx
King Saud University
Saudi Journal of Biological Sciences
www.ksu.edu.sawww.sciencedirect.com
http://dx.doi.org/10.1016/j.sjbs.2016.01.0271319-562X � 2016 The Authors. Production and hosting by Elsevier B.V. on behalf of King Saud University.This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027
dependence on petroleum-based sources (Zhijiang et al., 2011;Iqbal et al., 2014a, 2015). To develop a polymeric compositematerial is an original concept/solution to expand and/or
impart ideal characteristics (specific strength, thermal proper-ties, surface properties, biocompatibility, and biodegradabil-ity) that native/pristine homogeneous materials fail to
demonstrate on their own. In recent years, with an everincreasing scientific knowledge, eco-friendly realization anddemands of legislative authorities, wasteful protection or de-
protection removal of synthetically prepared petroleum-based materials and the development of structured compositeare being considered more critically (Datta and Włoch, 2014;Iqbal et al., 2014b).
Green chemistry has many challenges for effective execu-tion of state-of-the-art technologies to reduce or eliminatethe use and/or generation of detrimental constituents during
the entire engineering/manufacturing processes. The use ofenzyme in grafting of biopolymers is a recent practice,where, enzyme offers eco-friendly and safer reaction environ-
ments to the current practices, as a green catalyst (Iqbalet al., 2014c, 2015), without the use of additional initiatorsand/or cross-linking agents. To acquire the anticipated func-
tionality in the final product it is very indispensable to grafttwo or more polymers with some other suitable moieties(Datta and Włoch, 2014), where individual polymer lacksthose functionalities to withstand on its own. From the last
few years, among many others, P(3HB) is of particular inter-est to prepare composites that can be synthesized by com-bining with other suitable homo-, or co-polymers. This
polymer is the focus of the work presented here, to producecomposites with EC, either to impart or improve thermaland mechanical characteristics, decrease brittleness, and/or
increase tensile strength of the pristine P(3HB).Oxidoreductases like laccase (EC 1.10.3.2) have tremendous
capability to react with a variety of suitable substrates. There is
now a new wave of interest in laccase mediated surface activa-
tion with a view to grafting materials of interest. There are sev-
eral advantages in the laccase-assisted grafting methods that
include: (i) high added-value; (ii) eco-friendly processing; (iii)
convenient preparation methods; (iv) minimum use of water
and energy, and finally (v) no or little use of harsh chemicals.
This study focuses on the development of green composites
with novel characteristics. A pure laccase from Aspergillus
niger was used to develop composites under mild and eco-
friendly processing conditions.
2. Materials and methods
2.1. Chemicals
A novel laccase obtained from A. niger through its heterolo-
gous expression in Saccharomyces cerevisiae was used as agreen catalyst for grafting purposes. A unit laccase activity(U) was defined as a lmol of ABTS oxidized per min at pH4.5 and 30 �C (emax 36000 M�1 cm�1). All other chemicals used
were of analytical laboratory grade and used as-received fromSigma–Aldrich Company Ltd., UK, VWR Chemicals, UK,and DIFCO, UK.
2.2. Bacillus subtilis and maintenance
A Gram+ bacterial strain B. subtilis NCTC 3610 was collectedfrom the University of Westminster’s bacterial culture collec-tion unit and used as a potential candidate to produce
P(3HB) polymer. The collected strain was streaked in its pureform on the sterilized nutrient agar plates and subsequentlyused for inoculum development. In order to obtain homoge-neous bacterial spore suspension, a pure colony was grown
overnight in 50 mL sterile nutrient broth at 30 �C and120 rpm. The initial bacterial concentration was maintainedapproximately at 105 CFU/mL in the freshly prepared spore
suspension by comparing OD600 using McFarland standardmethod.
2.3. P(3HB) production and extraction
P(3HB) polymer was produced from B. subtilis NCTC 3610under some previously optimized fermentation using as
reported modified G medium (MGM) (Akaraonye et al.,2010). After the stipulated fermentation time (72 h),as-reported chloroform–hypochlorite dispersion method (Raiet al., 2011) was adopted to extract P(3HB) polymer from
the fermented culture. Following that the freshly extractedpolymer was placed in the desiccated jar to avoid free moistureabsorption by the P(3HB) and used further in subsequent graft
synthesis experiments.
2.4. Grafting tool
A fungal laccase from A. niger, through its heterologousexpression in S. cerevisiae, was produced. Briefly, a Bioflo3000bioreactor was used to ferment 0.5 L culture and the fermenta-
tion conditions were: 20 g/L glucose, pH 5.5, aeration of0.6 VVM (volume of air/volume of culture medium/min),106 spore/mL inoculum and 120 mg/L syringaldazine as sub-strate. A simple chromatographic purification step (anionic
exchanger, 50% final yield) allowed us to recover 2.3 g of lac-case with a specific activity of 50 U/mg and a satisfactory levelof homogeneity as controlled by UV/VIS spectroscopy and
denaturing gel electrophoresis (Mekmouche et al., 2014).
2.5. Grafting of P(3HB) onto the EC
A pure laccase from A. niger was used with and without ABTSas a laccase-mediator to develop composites between P(3HB)and EC using P(3HB): EC (50: 50) under an ambient environ-ment. Briefly, P(3HB) obtained from B. subtilis NCTC 3610,
and EC were treated with laccase from A. niger at 25 �C for30 min. The laccase-assisted reaction mixture comprising ofP(3HB) and EC was poured into the labeled sterile petri plates.
This was then followed by incubation at 50 �C for 24 h to castthe composites. Finally, the composites were designated asP(3HB)-g-ECA (prepared using laccase supplemented with
ABTS as a mediator) and P(3HB)-g-ECB (prepared using purelaccase alone). The resulting enzymatically grafted compositeswere then characterized using various analytical techniques as
described below.
2 H.M.N. Iqbal et al.
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027
FT-IR spectra were recorded from the wavelength region of4000–500 cm�1 using a Perkin Elmer System 2000 FT-IR spec-trophotometer. Morphological characterization was per-
formed in ultra-high vacuum mode using scanning electronmicroscope (Philips, XL-30, FEG SEM; EFI, Netherlands).To investigate the thermal and mechanical characteristics aPyris Diamond Differential scanning calorimeter (Perkin–
Elmer Instruments, USA) and a Perkin–Elmer dynamicmechanical analyzer (DMA) Q800 were used respectively. Awide-angle X-ray diffraction with a thin film attachment using
a Bruker D-8 Advance X-ray diffractometer equipped with Nifiltered Cu–K radiation was used to investigate crystallinestructures. A pendant drop method was adopted to measure
hydrophobic and hydrophilic characteristics using a KSVCam 200 optical contact angle analyzer (KSV instrumentsLtd., Finland).
3. Results and discussion
3.1. FT-IR spectroscopy
The IR absorption found at 3450 cm�1 for P(3HB) was shiftedto 3358 cm�1 for P(3HB)-g-ECA (Fig. 1). The peak assigned to
the O–H stretching vibration at 3358 cm�1 intensified in theP(3HB)-g-ECA composite because of the contributions fromthe –OH group of EC. Furthermore, IR characteristic bands
at 2980 and 2867 cm�1 belonging to stretching vibration ofCH3 and aliphatic C–H bond from alkyl groups of P(3HB).A sharp band observed at 1721 cm�1 is assigned to the
C‚O stretching vibration. The bands with characteristicpeaks at 1260, 1353, 1456, 1721, and 2926 cm�1 were particu-larly attributed to the bending modes of C–H, stretching vibra-
tion of C‚O, and symmetric and asymmetric stretchingvibration of CH3, respectively (Liu et al., 2009). Previously,
FT-IR spectroscopy has been used to prove the existence ofhydrogen bonding interactions in the different compositesbased on cellulose/PHBV blends at different compositions
(Hameed et al., 2011). A broad peak between 3376 and3500 cm�1 indicating cellulose O–H vibration, while the peakat 1050–1100 cm�1 region is due to the stretching of the
C–O–C linkage of ethyl cellulose molecules (Mohammed-Ziegler et al., 2008; Iqbal et al., 2014a).
3.2. X-ray diffraction (XRD)
XRD profile for pristine P(3HB) showed distinct peaks at 2-hvalues of 28�, 32�, 34�, 39�, 46�, 57�, 64�, 78�, and 84�. Theresults obtained through XRD analysis evidently support thatthe extent of P(3HB) crystallinity was greatly reduced due tothe homogeneous incorporation of semi crystalline materiali.e., EC, in this study, into the polymeric matrix (Fig. 2). Ethyl
cellulose, as a semi-crystalline material, can suppress andbreak the crystalline domains of the crystalline polymers(Davidovich-Pinhas et al., 2014), thus the crystallization of
P(3HB) in P(3HB)-g-EC composites would be restricted as evi-denced by XRD analyses. For the EC, a main scattering inten-sity peak can be identified at 2-Theta value of 21.2� as shownin the Fig. 2, which is assigned to the reflexion planes ofcellulose I.
3.3. Scanning electron microscopy (SEM)
Fig. 3 confirms the morphological changes via surfacetopographies of the pristine polymers and grafted compositesi.e., P(3HB)-g-ECA and P(3HB)-g-ECB observed using
SEM micrographs. As compared to the P(3HB)-g-ECB,P(3HB)-g-ECA showed homogenous dispersion of P(3HB)within the backbone polymer. Based on the data reported in
an earlier literature graft copolymerization can modify thephysiochemical and morphological characteristics of the
Figure 1 Typical FT-IR spectra of individual polymers i.e., P(3HB) and EC and their grafted composites i.e., P(3HB)-g-ECA and P
(3HB)-g-ECB.
Laccase-assisted green composites with novel characteristics 3
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027
grafted materials, which in turn affect their bio-compatibilityand biodegradability (Iqbal et al., 2014b). This change in sur-face morphology supported the successful occurrence of graftpolymerization (Yu et al., 2012).
3.4. Differential scanning calorimetry (DSC)
The results obtained after DSC analyses are summarized inTable 1. In comparison to the two forms of laccase (withand without ABTS) used two different profiles were recorded.
In comparison to the untreated P(3HB) an increase in the Tg,and Tm values was observed in case of the P(3HB)-g-EC com-posite prepared using laccase as a catalyst. One possible expla-nation of this increase in the Tg and Tm values in case of P
(3HB)-g-EC is a re-joining of short segments would cause anincrease in the Tg and Tm due to the better impregnation ofthermally stable cellulosic component as reinforcement into
the P(3HB) matrix. Herein, the parameter Tc is used to mea-sure the overall rate of crystallization, and the smaller the Tc
the greater the rate of crystallization (Liu et al., 2009; Yu
et al., 2012).
3.5. Dynamic mechanical analyzer (DMA)
Stress–strain curves were used to calculate the mechanicalcharacteristics of the tested materials which showed simultane-ous improvement in the tensile strength and Young’s modulusas compared to the individual P(3HB) counterpart because the
high strength of EC allowed the mechanical properties of thecomposite to improve. The results obtained after DMA mea-surements are summarized in Table 2. A gradual increase in
the tensile strength and Young’s modulus values was observedin case of the P(3HB) containing P(3HB)-g-EC composites ascompared to the pristine P(3HB) polymer (Table 2). A persis-
tent reinforcement or low filler loaded network bargainsincredible enhancement in the mechanical assets, in particular,the tensile strength and Young’s modulus (Iqbal et al., 2014b).
Figure 2 XRD profiles of individual polymers i.e., P(3HB) and
EC and their grafted composites i.e., P(3HB)-g-ECA and P(3HB)-
g-ECB.
Figure 3 SEM micrographs of individual and grafted materials used in the present study: (A) P(3HB)-g-ECA, (B) P(3HB)-g-ECB,
(C) P(3HB) and (D) EC.
4 H.M.N. Iqbal et al.
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027
The surface energy of the solid materials can be estimated bymeans of contact angle measurement together with a theoryof intermolecular forces. Therefore, in this experiment, the
drop contour analysis was used for determining the surfacetension and the water contact angle. The characteristic WCAfeatures of the resulting composites are shown in Fig. 4. A dra-
matic reduction from 68� to 35� was observed in the contactangle of P(3HB) as compared to the composite prepared usinglaccase from A. niger. However, an increase in the surface
tension properties from 20.5 mN/m to 72.5 mN/m wasrecorded in the P(3HB)-g-ECA. The WCA profile ofP(3HB)-g-ECA and P(3HB)-g-ECB indicates that the hydro-
philic property of the composite is much better than pureP(3HB). According to the literature, such a result is probablyaccounted because of the high hydrophilic nature of EC and
P(3HB) interaction involving the carbonyl group with thehydroxyl group from EC. It has also been reported in the lit-erature that the grafted polymers with more hydroxyl groups
of short chains exhibited more hydrophilic characteristics thanother copolymers (Yu et al., 2012).
4. Conclusions
In summary, laccase-assisted grafting is quite a new and attrac-tive technique from green chemistry technologies. Therefore,
the composite materials developed using natural biopolymersin combination with enzymatic catalysis would prove to begreen in their preparation and performance. The above-discussed newly synthesized composites are expected to find
potential applications in various sectors, where environmen-tally friendly polymer composites with novel characteristicsare of utmost importance. The newly grafted composites under
an enzymatic environment exhibited some unique functionali-ties and characteristics such as good tensile strength, andmechanical strength due to its unique graft structure.
Figure 4 WCA profile of individual polymers i.e., P(3HB) and EC and their grafted composites i.e., P(3HB)-g-ECA and P(3HB)-g-ECB.
Table 1 Thermal characteristics of individual polymers i.e., P(3HB) and EC and their grafted composites i.e., P(3HB)-g-ECA and P
Table 2 Mechanical characteristics of individual polymers
i.e., P(3HB) and EC and their grafted composites i.e.,
P(3HB)-g-ECA and P(3HB)-g-ECB.
Samples TS (MPa) YM (GPa) EB (%)
P(3HB) ND ND ND
EC 122 ± 9.85 3.38 ± 0.85 8.2 ± 1.25
P(3HB)-g-ECA 78 ± 3.35 0.91 ± 2.15 19.2 ± 2.65
P(3HB)-g-ECB 46 ± 1.33 1.10 ± 2.36 10.4 ± 1.42
Where, ND: not detected; TS: tensile strength; YM: Young’s
modulus and EB: elongation at break.
Laccase-assisted green composites with novel characteristics 5
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027
Please cite this article in press as: Iqbal, H.M.N. et al., Laccase from Aspergillus niger: A novel tool to graft multifunctional materials of interests and their charac-terization. Saudi Journal of Biological Sciences (2016), http://dx.doi.org/10.1016/j.sjbs.2016.01.027