-
1DALI Command MultiDimintelligent lighting control system
IntroductionThe Philips MultiDim systemconsists of an integrated
range ofDALI compatible devices that canbe combined to produce a
fullyfunctional lighting control systemfor use with DALI ballasts
andLamp Interface Units*.
The MultiDim range includescontrollers, configuration
softwareand a DALI/LON Gateway thatallows multiple DALI systems
tobe integrated with LON basedbuilding management systems. Allof
the MultiDim componentshave been designed to worktogether to make
the installationof a DALI network as simple andas trouble free as
possible.
This datasheet covers the basicMultiDim control products
thatwill form the basis of a DALIsystem, and includes details
andspecifications for the followingproducts:
Modular Control PanelsDCMD100 - DCMD170
MultiSensor DCMD302
IR Remote ControlDCMD303
Transistor DimmerDCMD450
DIN Rail Power SupplyDCMD400
Ceiling Mounted PowerSupply DCMD401
Related Products Philips HF-Regulator DALI
compatible Ballasts. Refer to theseparate datasheet for
details
MultiDim PC Programming Kit(DCMD502). Provides acomplete, PC
based, solutionfor the design and configurationof MultiDim Systems.
Includes:MultiDim PC Serial Interface(DCMD501), MultiDimProgramming
Point(DCMD200/180) and a fullyworking copy of MultiDimToolbox
configuration software.Refer to the DCMD502datasheet for
details
DALI/Lon Gateway(DCMD430). Allows multipleDALI systems to be
integratedwith LON based buildingmanagement systems. Refer tothe
DCMD430 datasheet fordetails
DALI/Push-button interface(DCMD444). Allows pushbuttons from
othermanufacturers to be connectedto the system.
* This document uses the general termLamp Interface Unit (or
itsabbreviation LIU) to mean any DALIcompatible electronic lamp
controller.A Lamp Interface Unit can be afluorescent ballast, a
transistor dimmerfor incandescent lamps, or any otherdevice
designed to directly drive aparticular lighting technology.
DCMD - Push-button modules
DCMD302 - Ceiling multisensor DCMD303 - IR remote control
About DALI DALI (Digital Addressable Lighting Interface) is a
new internationalstandard (IEC929) for lighting control systems.The
main features of theDALI standard are as follows:
Individual Control of Lamps. Each unit in the DALI network has
itsown individual address and can be controlled independently.
Multi-Channelling. A single control cable can be used to
controlseveral different groups of lamps.
No Mains Switching Required. Lamps can be dimmed or switched
onand off using control system commands without any need for
mainsswitching.
Back-Channelling.The information flow on the connecting cable is
bi-directional. In addition to commands from controllers, the cable
canalso carry status information on the lamp's operating
condition.
DCMD450 - 800 W Dimmer
Provisional
Simple Wiring. All of the units in the system are interconnected
usinga simple two-core cable with few restrictions on topology. Up
to 64devices can be connected with a maximum cable length of
300metres.
Easy System Re-Configuration.The operation of the system can
bechanged quickly without any modification to the hardware.
Easy System Modification. If the lighting system needs to be
enlarged,new components can be added anywhere on the DALI
cable.Existing units can easily be reconfigured to suit changing
usagepatterns.
-
2DALI Command MultiDim intelligent lighting control system
Introduction The MultiDim product range provides a complete and
fully integratedmeans of creating a DALI based digital control
systems. MultiDimcomponents support all of the basic functionality
of a standard DALIsystem and are easy to install and configure.
Designing a MultiDimsystem is a very straightforward process, but
there are several thingsthat you need to be aware of.The
information on these two pagesshould provide everything that you
need to know.
DALI Compatibility andComplianceThe MultiDim controllers can
beused with any DALI compatibleballast or Lamp Interface Unit.
Inaddition, all MultiDim LampInterface Units (such as the 800Watt
Dimmer) and the DALI-LonGateway can be used inconjunction with
othermanufacturer's DALI compatiblecontrol systems. However, it
maynot be possible (and is notrecommended) to use
MultiDimcontrollers on the same system asother types of DALI
controller.
Cable Choice The electrical specification forDALI systems
provides a greatdeal of flexibility in both thechoice of cable used
and how it isinstalled.The basic requirementsare:
The cable be mains rated.
2 wire, 0.5 - 1.5 mm2
The maximum voltage drop onthe DALI cable must notexceed 2 Volts
(for standardcables, this means that the totallength of connecting
cable canbe up to 300 metres).
This means that standard mainscable can be used successfully
-particularly useful where a systemis being retrofitted to an
existinginstallation.
Cable TopologyAs you can see from the layoutdiagram opposite,
there are fewrestrictions of the cable topology.
No special terminations arerequired, and there are nocomplex
rules about how thenodes should be connectedtogether.
Ring configurations should beavoided, but otherwise the
onlyrequirements are that the cablebe continuous throughout,
andthat each node be connected tothe cable at some point.
Nodes can be daisy chainedtogether in series and spurs beadded
at any point.The cabletopology can be optimised toeither simplify
testing or tominimise cable use.
DALI ConnectionsAll MultiDim units are fitted withremovable
connectors withpaired terminals for the DALIconnection.These
provide asimple means of linking through,and the only requirement
is tomaintain the power supplypolarity throughout the system.
Power Supply RequirementsMultiDim Controllers without adirect
mains connection must beprovided with power via theDALI control
cable.This has theadvantage that no additionalpower cabling is
required, but itdoes mean that you have toensure that an adequate
powersupply is available on the system.This supply must be designed
forDALI use and be capable ofproviding sufficient power tosupply
the controllers connectedto the system. In addition, tomaintain
signalling integrity, it mustnot be capable of providing morethan
250 mA to the system.
See page 10 for details of thededicated MultiDim Power
SupplyUnits.
ConfigurationAll MultiDim units are fullyconfigurable.They are
suppliedpre-configured with factorydefault settings that ensure
thata system will be functional assoon as the power is applied.
This has the advantage that anewly installed system will
providebasic operation from the momentthe power is first applied.
Forsimple systems, this may be allthat is required. But for
systemsthat are more complex (and togain access to advanced
MultiDimfunctions) the system must bereconfigured using one of
threedifferent methods:
Configuration Using ButtonControllers. Eight and fivebutton
MultiDim panelcontrollers provide somelimited configuration
featuresfrom the control buttons.Theseinclude the ability to store
fourpre-set light levels and theability to customise those
levels.
Configuration Using the IRRemote Control Unit.TheMultiDim IR
remote controlunit can be used to configure anumber of advanced
systemfunctions. For more details seepage 9 of this datasheet.
Configuration Using MultiDimToolbox software.The MultiDimToolbox
(DCMD502) is aWindows based softwareconfiguration tool, designed
tomake setting up a complexsystem as simple as possible.See the
MultiDim Toolboxdatasheet for more details.
MultiDim Terminal Connections UsingScreened Cable
(optional).
MultiDim Terminal Connections UsingStandard Cable.
About MultiDim Systems
DA+
DA+ DA+
SC
SC SC
DA-
DA- DA-
DA+
DA+ DA+
SC DA-
DA- DA-
-
3DALI Command MultiDim intelligent lighting control system
D C M D 4 0 1
9137 005 30303MADE INNORWAY
P ower S upp lyInput: 230VAC 50 - 60Hz 100mAOutput:250mA 16V
DALI ST ATUS
DL
IA
DA
LI P
OW
ER O
UT
1
3 4
2
0/1
8
4
7 6 5
2
3
1L & N
DALI ballast
DALI ballast
DALI ballast
Physicalselection
DA+
ENL
LOCAL CONTROL
Sc DA- DALI POWER
ONOFF
StatusLED
800W DIMMER
DCMD4501 5
2 6
3 7
4 O
About MultiDim Systems
1.The MultiDim system can be used with any DALI
compliantelectronic ballast for fluorescent lamps.
2. Power for the controllers can be supplied by the
DCMD401(illustrated) or the DCMD400 DIN rail-mounted power supply
orany mains connected MultiDim unit such as the DCMD450 Dimmer.
3. Low-cost cable can be used to interconnect all of the
systemcomponents.The recommended total length of the cable is
max.300 m.
4.The MultiDim Multisensor provides IR, light-level and
occupancysensor, which can be used independently or in combined to
provideenergy-saving functions such as automatic operation and
constantlight level.
5.The MultiDim DCMD450 800 Watt dimmer is a fully compliantDALI
LIU for use with incandescent lamps and low-voltage
electronictransformers.
6.The single-gang panels can contain one of the control
modules.Themodules are available as sliders, rotary controls or
button panels.
7.The double-gang panels can contain up to three controller
modules.The modules are completely interchangeable within the
panel, andcustom panels can be created as desired.
8.The MultiDim IR remote control unit provides both means
ofcontrolling individual units and a simple configuration tool. All
of themodular controllers and the MultiSensor are fitted with IR
sensorand can be used with the remote control.
Typical layout of a MultiDim systemTypical layout of a MultiDim
system
-
4DALI Command MultiDim intelligent lighting control system
MultiDim Modular Control Panels
IntroductionA range of DALI compatiblemanual control panels that
can beconfigured to suit almost anycontrol requirement.The
rangeincludes pushbutton, rotary, andslider control modules, all
ofwhich can be inserted into eithersingle or triple gang fascia
panels.The modular constructionprovides flexibility and allowsmany
different panelconfigurations to be constructed.
All of the control modules arefitted with indicator LEDs and
anIR receiver that allows themodule operate with theMultiDim IR
remote control unit.
ConfigurationEach control is supplied pre-configured with
immediatelyusable default settings, but can beeasily re-configured
to suit aparticular application using eitherthe MultiDim IR Remote,
orMultiDim Toolbox configurationsoftware.The eight and fivebutton
controllers also providelimited configuration featuresusing the
control buttons.
1
2
3
4 O
1 5
2 6
3 7
4 O
1
2
3
4 O
IR Receiver Eight Button
Two Button On/Off Rotary - Push On/Off
Five Button + Raise/Lower Five Button
Slider Double Slider
Two Button - Raise/Lower Blank Panel
IntroductionA range of DALI compatiblemanual control panels that
can beconfigured to suit almost anycontrol requirement.The
rangeincludes pushbutton, rotary, andslider control modules, all
ofwhich can be inserted into eithersingle or triple gang fascia
panels.The modular constructionprovides flexibility and allowsmany
different panelconfigurations to be constructed.
All of the control modules arefitted with indicator LEDs and
anIR receiver that allows themodule operate with theMultiDim IR
remote control unit.
IR Receiver
-
5DALI Command MultiDim intelligent lighting control system
MultiDim Modular Control Panels
Module DimensionsThe chassis plates and fasciapanels are
designed to fit bothDIN and UK standard backboxeswith a minimum
depth of 35 mm.
Mechanical DataThe modular controllers are available in satin
white plastic finish.Thevarious control panel combinations can be
constructed from thefollowing separately packaged components:
The Control Modules (see opposite for variations).
Single gang chassis plate and fascia panel, designed for use
with astandard, single gang backbox.This provides a mounting for a
singlemodule.
Triple gang chassis plate and fascia panel, designed for use
with astandard, double gang backbox.This provides a mounting for up
tothree modules.
DALI Cable ConnectionStandard MultiDim removable connectors with
paired terminals.A connection between the SC terminal and a local
earth is requiredfor EMC protection.
Module Power Supply Requirements13-19 V, 10 mA supplied via DALI
network cables.
Conformity & StandardsEMC
Emission: EN 55 015Immunity: EN 61 547
SafetySafety: EN 60 669-1, IEC 60 669-2-1Isolation: 4 kVIP
rating: 30
Environmental RequirementsAmbient temperature: 0...35CStorage
temperature: -10...+70CRelative humidity: 90% maximum,
non-condensing.
DA+ SC DA-
DA-DA+ DA+DA-
141.80
73.80
73.80
73.80
35.40 31.80
48.40
-
6DALI Command MultiDim intelligent lighting control system
MultiDim MultiSensor
IntroductionA ceiling mounted module,containing the sensors
requiredto provide an automated DALIlighting control
system.TheMultiSensor contains an Infra-Redreceiver for use with
theMultiDim IR Remote, a constantlight sensor (which
measuresreflected light from below thedevice), and a PIR
occupancysensor with a range of up to4.5 metres.
PIR OperationThe PIR sensor can be used onits own to provide
automaticcontrol of lighting depending onthe rooms
occupancy.Theoperation and timing of the PIR isfully configurable
and includes theability to set the unit to provideoff only
operation and anadjustable PIR transition timethat can improve the
life-span offluorescent tubes used in corridorapplications.
Local SwitchThe MultiSensor is provided withterminal connectors
for a localwall switch.This provides amanual dimming function
ifrequired.
ConfigurationThe MultiSensor is supplied pre-configured with
immediatelyusable default settings. However, itcan be easily
re-configured to suita particular application usingeither the
MultiDim IR Remote,or MultiDim Toolbox software.
In addition, the MultiSensor isfitted with five rear mounted
DILswitches that will allow some ofthe main functions to be
pre-configured.The DIL switchsettings are applied when poweris
first applied but can beoverridden using the MultiDim IRRemote, or
MultiDim Toolboxsoftware.
Constant Light OperationThe PIR and constant lightsensors
operate together toprovide automatic constant lightcontrol of the
surrounding lamps.
For effective constant lightoperation, careful positioning ofthe
MultiSensor is essential. Inparticular, it is important toensure
that the sensor is notexposed to direct light, and that it
is positioned in such a way thatmost of the light that it
receives isunder its control. Mount theMultiSensor away from direct
lightentering through windows. Seethe installation instructions
formore details.The constant lightfeature is disabled by default
andmust be enabled using theMultiDim IR Remote Control orMultiDim
Toolbox software.
IR Sensor
ConstantLight Sensor
PIR
60- 85
4.5 m
0.5 m
3.0 m
3.0 m
120
3 m
14.0 m
1.6 m
0.8 m
100
7.1 m
5.2 m
3.0 m
IR Sensor Range and Angle of View
Constant Light Sensor Range and Angle of View (without
Restrictor)
PIR Sensor Range and Angle of View
-
7DALI Command MultiDim intelligent lighting control system
MultiDim MultiSensor
Fixing DataThe MultiSensors housing isdesigned for push fit
mountinginto a ceiling, or inside a luminairecasing. Its
spring-loaded mountingsystem will allow it to be fittedinto a wide
range of fixingmaterials, including sheet metaland fibrous ceiling
tiles. For thinmaterials, a slightly smallermounting hole is
required. / 52.0 mm
0.5 mm- 2.0 mm
/ 55.0 mm>2.0 mm
/ 65.00
26.40
51.40
SC DA-DA+
Touch DimmerCable
fadeN.o
Switch (Mains rated)
0.22 - 2.5 mm(Mains rated)
2MomentaryI
Operation
HoldMomentary
5
32
14
OFF
5
DA+SC
DA-
05
32
On
14
OFF
PIR Control
IR Receiver
PIR Test
Factory DefaultSettings
Local Switch
Constant Light
Off
Switch Function
On
Off
Off
40
2.1 m
3.0 m
Manual Configuration Using the MultiSensors DIL switch
Connecting a Local Switch
Fitting the Constant Light Sensor Viewing Angle Restrictor
DCMD302 - for ceiling mounting With the cable shroud
removed.
DALI Cable ConnectionStandard MultiDim removable connectors with
paired terminals.
Module Power Supply13 - 19 V, 15 mA supplied via DALI network
cables.
Constant Light SensorViewing Angle: 100 (40 with viewing
angle
restrictor) Range: 5 - 5000 lux.SW1 Switch Functions: On: Set
level to nominal value
Off: Defaults to maximum IR Receiver Operation: Omni-directional
Frequency: 36 kHz SW2 Switch Functions: On: Receives all remote
control
commands Off: Ignores remote controlcommands (except
configurationcommands)
PIR Sensor Operation: Omni-directional pyro-electric SW3 Switch
Functions: On: Last level recall
Off: PIR response ignored SW4 (PIR Test) Switch Functions:
On:Timeout reduced to
10 seconds - use for testing Off: Normal PIR function (default
20 minute time-out)
Local switch Operation: Single mechanical switch
connected as shown providestouch dimmer style operation.
SW5 Switch Functions:On: Local Switch enabled.Off: Local Switch
disabled.Conformity and Standards (EMC) Emission: EN 55 015
Immunity: EN 61 547 Safety: IEC 60 950 Isolation: 4 kV IP rating:
30 Operating ConditionsAmbient temperature: 0...+50C Storage
temperature: -10...+70C Relative Humidity: 90% maximum,
non-condensing.
-
8DALI Command MultiDim intelligent lighting control system
MultiDim IR Remote Control
1
34
2
0/10/1
+
E
C
D
B
G
A
F
9
D 4
0E 2
5
8
7 6
B
A
F
C
3
1
A. LED Indicator (Flashes when a button is operated)B. Scene
Recall/ConfigurationC. On/Off/ShiftD. Modifier KeysE. TransmitterF.
Battery CoverG. Rotary Switch (Normal position 0)
IntroductionThe MultiDim Infra-red remotecontrol is designed to
work inconjunction with all PhilipsMultiDim products fitted with
anIR receiver, including the PhilipsMultiDim control panels
andMultiSensor.
The IR Remote is a dual functiondevice. Its main purpose is
toprovide a simple and intuitiveremote control for MultiDimcontrol
systems.
When used as such, it provides anumber of basic
functions,including On/Off, Raise/Lower, andselecting from four
predefinedScenes.
However, the IR Remote can alsobe used as a basic
configurationtool for simple systems where theuse of MultiDim
Toolbox and itsassociated Programming Pointis inconvenient.
In this case, the control buttonsare used in combination
toprovide basic configurationfunctions.This includes, creatingand
adding to groups of lamps,setting pre-set scenes anddisabling or
enabling IR receivers.The IR Remote will allow thesettings to be
locked to preventthe user from accidentally makingchanges to the
configuration.
Basic Control FunctionsOn/OffRecall Scene 1-4Raise/Lower lamp
levelsStore Scene
Configuration FunctionsSet default Preset Levels (1 = 100%, 2 =
75%, 3 = 50%, 4 = 25%)Creating GroupAdd to GroupCreating
SceneRestrict the IR Control signal to Specific
GroupsDisable/Enable IR sensors on specific
controllersConfiguration Lock (prevents users inadvertently
changing thesettings)
Technical DataPower: 2 x IEC, LR03/AAA, 1.5 V BatteryWeight: 50
gOperating Frequency: 36 kHzSize: 120 mm x 57 mm x 24 mm
-
9DALI Command MultiDim intelligent lighting control system
MultiDim 800 W Transistor Dimmer
LOCAL CONTROL
DALI
AC
45 m
m
88 mm 58 mm
90 m
m
Physicalselection
DA+
ENL
LOCAL CONTROL
Sc DA- DALI POWER
ONOFF
StatusLED
800W DIMMER
DCMD450
DALI + 250 mA
PhysicalSelectionSwitch
DALI
Status LED
ONON
Physicalselection
DA+
ENL
LOCAL CONTROL
Sc DA- DALI POWER
ONOFF
StatusLED
800W DIMMER
DCMD450
DALI
LOCAL CONTROL
AC
L
N230 V
DA+
DA+DA+
SC DA-
DA- DA-
< 50 m
IntroductionThe MultiDim 800 Watt TransistorDimmer is a fully
DALIcompatible Lamp Interface Unit,designed to allow
incandescentlamps to be incorporated into aDALI controlled lighting
system.
The dimmer is a DIN-railmounted unit that can control amaximum
load of up to 800 W.It can be connected to mainsvoltage lamps
directly, or to lowvoltage lamps via an electronictransformer
designed for bothcapacitive and resistive loads.
The dimmer is provided withlocal switch terminals, an
indicatorLED, a physical selection switchand a built-in DALI power
supply.
The local switch terminals willallow a momentary push
buttonswitch to provide local touchdimmer style control.The
indicator LED provides statusand fault indications, and thephysical
selection switch is usedto identify the device duringsystem
configuration.
The DALI power supply is switchactivated, and will provide up
tothe maximum of 250 mA, 18 V tothe DALI network.
Note that, if the power supply isenabled, no other source
ofpower may be used on thenetwork.
Additional DALI Functions Min/Max levels, Scenes, Groups Lamp
status report Dimmer status report
ConnectionDALI: Standard MultiDim removable
connectors with paired terminalsMains: < 4 mm2 solid core
< 2.5 mm2 stranded
PowerMains Supply: 220-240 VAC, 50 HzDALI supply output: 250
mA
Operating ConditionsAmbient Temperature: 0...35CRelative
Humidity: 90% max, non-condensing.
Mechanical dataDIN-rail case 88 mm wide (5 M)
Conformity & Standards (EMC)Emission: EN 55 015Immunity: EN
61 547
SafetySafety: EN 60 950IP rating: 30Isolation: 4 kV, Mains to
dimmer unit
(Basic, Dimmer internal isolationto DALI terminals)
Installation Notes1.The dimmer is for use with incandescent
lamps and low voltage
electronic transformers. It is not suitable for use with
fluorescentballasts or conventional transformers.
2.The external supply must be protected. It is recommended that
a 6 A MCB is used.
3. All cabling must be 230 V mains rated.4. For installation in
a restricted access location only.
-
10
DALI Command MultiDim intelligent lighting control system
MultiDim Power Supplies
DALI
AC
45 m
m
58 mm
90 m
m
70 mm
POWER SUPPLY
DCMD400
DA+
ENL
Sc DA-
Power
L
N230V
AC
DA+DA+ DA- DA-
DA+ SC DA-
DALI
63 m
m
100 mm
D C M D 4 0 1
9137 005 30303MADE INNORWAY
P ower S upp lyInput: 230VAC 50 - 60Hz 100mAOutput:250mA 16V
DALI ST ATUS
DL
IA
DA
LI P
OW
ER O
UT
51 mm
L
L
DA N
N
DALI HF BALLAST
DCMD401
DALIL
N
230V
DA+ DA-
DA+ SC DA-
DALI
DCMD401 DCMD400
DCMD400 Module Dimensions
DCMD400 Module Wiring
DCMD401 Module Dimensions DCMD401 Module Wiring
IntroductionPower for MultiDim devices can be supplied from a
number ofdifferent sources. All mains connected MultiDim units
(such as the 800Watt Dimmer) are provided with an internal DALI
power supply. If thesystem contains one of these, it will provide
an ideal source of power.
Alternatively, a dedicated MultiDim power supply unit (DCMD 400
orDCMD 401) can be used. Both of these units have similar
outputcapabilities and can supply the maximum of 250 mA permitted
for aDALI system. However, the DCMD 400 is designed for DIN
railmounting in a control cabinet and the DCMD 401 for mounting in
aceiling void.
Note that, if a power supply unit is connected to the system, no
othersource of power may be used.
Technical DataMains SupplyDCMD400: 230 VAC (nom), 197-264
VAC(abs);
50 Hz (nom), 48-62 Hz (abs)DCMD401: 230 VAC -10%/ +6%, 50-60
Hz
DALI Supply Output250 mA (nom)
Ambient TemperatureDCMD400: 0...50CDCMD401: 0...40C
Relative Humidity90% max, non-condensing
IP rating30
Mechanical DataDCMD400: DIN Rail case 70 mm (4 M)
DALI CableDCMD400: Standard MultiDim removable connectors
with paired terminalsDCMD401: 1 m, 2 x 0.75 mm2 stranded
Mains CableDCMD400: < 4 mm2 solid core
< 2.5 mm2 strandedDCMD401: 1.5 m, 2 x 0.75 mm2 stranded
Installation Notes1.The external supply must be protected. It is
recommended that a 2A
MCB is used.2. All cabling must be 230 V mains rated.3.The
DCMD400 is for installation in a restricted access location
only.
-
11
DALI Command MultiDim intelligent lighting control system
MultiDim DALI Controllers
Type Description Ordering 1 Piece EOCnumber EAN1 code * Weight
Qty. Dimensions Volume
EAN3 code * gross l x w x hkg pcs cm m3
DCMD100 MultiDim rotary module 9137 005 308.. 8711500 747921
0.076 1 10.0 x 6.0 x 5.2 0.0003 747921 00DCMD110 MultiDim single
slider module 9137 005 309.. 8711500 747938 0.079 1 10.0 x 6.0 x
5.2 0.0003 747939 00DCMD111 MultiDim twin slider module 9137 005
310.. 8711500 747945 0.079 1 10.0 x 6.0 x 5.2 0.0003 747945
00DCMD121 MultiDim 2-button on/off module 9137 005 311.. 8711500
747952 0.079 1 10.0 x 6.0 x 5.2 0.0003 747952 00DCMD122 MultiDim
2-button raise/lower module 9137 005 312.. 8711500 747969 0.074 1
10.0 x 6.0 x 5.2 0.0003 747969 00DCMD124 MultiDim 5-button module
9137 005 313.. 8711500 747976 0.077 1 10.0 x 6.0 x 5.2 0.0003
747976 00DCMD125 MultiDim 7-button module 9137 005 314.. 8711500
747983 0.077 1 10.0 x 6.0 x 5.2 0.0003 747983 00DCMD126 MultiDim
8-button module 9137 005 315.. 8711500 747990 0.075 1 10.0 x 6.0 x
5.2 0.0003 747990 00DCMD150 MultiDim single blank module 9137 005
316.. 8711500 748003 0.049 1 10.0 x 6.0 x 5.2 0.0003 748003
00DCMD170 MultiDim IR receiver module 9137 005 317.. 8711500 748010
0.072 1 10.0 x 6.0 x 5.2 0.0003 748010 00DCMD180 MultiDim
programming point module 9137 005 318.. 8711500 748027 0.066 1 10.0
x 6.0 x 5.2 0.0003 748027 00DCMD200D MultiDim double frame - white
9137 005 319.. 8711500 748034 0.165 1 20.0 x 12.3 x 4.4 0.0011
748034 00DCMD200S MultiDim single frame - white 9137 005 320..
8711500 748041 0.096 1 12.2 x 10.0 x 4.4 0.0005 748041 00DCMD302
MultiDim ceiling multisensor 9137 005 301.. 8711500 747877 0.108 1
10.4 x 9.7 x 7.3 0.0007 747877 00DCMD303 MultiDim IR remote control
9137 005 302.. 8711500 747884 0.090 1 13.0 x 6.0 x 2.9 0.0002
747884 00DCMD400 MultiDim DIN rail-mounted power supply 9137 005
304.. 8711500 747891 0.168 1 11.0 x 8.0 x 6.8 0.0006 747891
00DCMD401 MultiDim ceiling-mounted power supply 9137 005 303..
8711500 748744 0.592 1 12.0 x 5.1 x 6.3 0.0004 748744 00DCMD444
MultiDim DALI/push-button interface 9137 001 820.. t.b.a. t.b.a.
t.b.a. t.b.a. t.b.a. t.b.a.DCMD450 MultiDim 800 W dimmer 9137 005
306.. 8711500 747914 0.258 1 10.1 x 9.1 x 6.3 0.0006 747914
00DCMD520 MultiDim PC programming kit 9137 005 307.. 8711500 749802
0.960 1 27 x 22 x 8.5 0.0050 749802 00* For all MultiDim products
the EAN1 code and the EAN3 code are the same.
Ordering and packing data