-
STR-ZA5000ES
MULTI CHANNEL AV RECEIVER
Installation Guide US
Guide d’installation FR
Guía de instalación ES
Before installing the receiver, be sure to update the receiver
to the latest software version.
Avant d’installer l’ampli-tuner, veillez à le mettre à jour à la
dernière version de logiciel.
Antes de instalar el receptor, asegúrese de actualizar el
receptor a la versión de software más reciente.
-
2GB
Map of GUI Menu System
Using the home menu
Menu items underlined are default settings.
HomeWatch BD/DVD
SAT/CATVGAMESTBVIDEOTV
Listen AUXSA‐CD/CDFM TUNERAM TUNER
Custom Preset MovieMusicPartyNight
Sound Effects Sound Field 2ch StereoDirectAuto Format
DecodingDolby SurroundNeural:XMulti Stereo
EqualizerSound Optimizer Normal
LowOff
In‐Ceiling Speaker Mode Front & CenterFrontOff
Pure Direct OnOff
-
3GB
Zone Controls Zone2 Power OnOff
Zone2 Input SOURCEBD/DVDSAT/CATVGAMESTBVIDEOAUXTVSA-CD/CDFM
TUNERAM TUNER
Zone2 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
Zone3 Power OnOff
Zone3 Input SOURCEVIDEOAUXTVSA-CD/CDFM TUNERAM TUNER
Zone3 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
-
4GB
Setup Input Setup*1 *2
IconNameWatch/ListenShow/HideHDMIOPTICAL/COAXIALCOMPONENTVIDEO
INAUDIO INInput ModePreset Sound FieldIn-Ceiling Speaker ModeA/V
SyncSubwoofer Low Pass FilterSubwoofer LevelPreset Gain
LevelTrigger 1Trigger 2Trigger 3
Speaker Setup Auto Calibration*3Automatic Phase Matching (Auto,
Off)Calibration Type (Full Flat, Engineer, Front Reference,
Off)Speaker PatternSpeaker ConnectionsSB Speaker Assign (Zone2,
Bi-Amp, Front B, Off)Height1 SP Assign (Zone2, Off)Size*4 (Large,
Small)Distance*4 (32 ft 9 in, 32 ft 8 in, …,
9 ft 10 in, …,
6 ft 7 in, 6 ft 6 in)Level*4 (+10.0dB,
+9.5dB, …, 0.0dB, …, –9.5dB,
–10.0dB)Test Tone*3Crossover Frequency*4 (40Hz, 50Hz, …, 120Hz,
…, 190Hz, 200Hz)Equalizer*4 (+10.0dB, +9.0dB, …, 0.0dB, …,
–9.0dB,
–10.0dB)Center Speaker Lift Up (10, 9, 8, …, 2, 1, Off)Surround
Speaker Position (Front, Back)Speaker Relocation (Type A, Type B,
Off)Ceiling Height (32 ft 9 in, 32 ft 8 in, …,
9 ft 0 in, …,
6 ft 7 in, 6 ft 6 in)Speaker Impedance
(8Ω, 4Ω)Distance Unit (feet, meter)
Network Setup Internet Setup*3Information*3Network Standby (On,
Off)Music Connect Device1 Connected Device
Input for Music Connect1
Preset VolumeOutput Zone
Device2 Connected DeviceInput for Music Connect2Preset
VolumeOutput Zone
-
5GB
Setup Audio Setup Digital Legato Linear (Auto 1, Auto 2,
Off)Sound Optimizer (Normal, Low, Off)Sound Field*3In-Ceiling
Speaker Mode (Front & Center, Front, Off)Pure Direct (On,
Off)Subwoofer Low Pass Filter (On, Off)A/V Sync (300 ms,
290 ms, …, 10 ms, 0 ms,
HDMI Auto)Dual Mono (Main, Sub, Main/Sub)Dynamic Range
Compressor
(Auto, On, Off)
Neural:X (On, Off)
HDMI Setup 4K Scaling (Auto, Off)Control for HDMI (On,
Off)Standby Linked to TV (Auto, On, Off)Audio Return Channel (On,
Off)Pass Through (Auto, On, Off)Audio Out (AMP, TV+AMP)Zone2 Audio
Out (AMP, Zone2 TV+AMP, Zone2 AMP)Subwoofer Level (Auto, +10dB,
0dB)HDMI Out B Mode (Main, Zone2)Priority (Main&Zone2, Main
Only)Fast View (Auto, Off)HDMI Signal Format HDMI IN 1 (Standard
format,
Enhanced format)HDMI IN 2 (Standard format,
Enhanced format)HDMI IN 3 (Standard format,
Enhanced format)HDMI IN 4 (Standard format,
Enhanced format)HDMI IN 5 (Standard format,
Enhanced format)
Zone Setup Zone Controls Zone2 Power (On, Off)Zone2 Input
(SOURCE, BD/DVD, …,
FM TUNER, AM TUNER)
Zone2 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
Zone3 Power (On, Off)Zone3 Input (SOURCE, VIDEO, …,
FM TUNER, AM TUNER)Zone3 Volume (+23.0dB, +22.5dB, …,
–40.0dB, …, –92.0dB, –∞dB)
Main Preset Volume (+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Main
Max Volume (+23.0dB, +22.5dB, ..., –40.0dB)Zone2 Preset Volume
(+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Zone2 Max Volume (+23.0dB,
+22.5dB, ..., –40.0dB)Zone2 Line Out (Variable, Fixed)Zone3 Preset
Volume (+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Zone3 Max Volume
(+23.0dB, +22.5dB, ..., –40.0dB)Zone3 Line Out (Variable,
Fixed)
-
6GB
Setup System Setup Language (English, Español, Français)Auto
Display (On, Off)Auto Standby (On, Off)Volume Display (Relative,
Absolute)Dimmer (Bright, Dark, Off)Sleep (2:00:00, 1:30:00,
1:00:00, 0:30:00, Off)Software VersionNetwork UpdateUSB
Update*3Tuner Setup*3 FM Mode
Name InputPreset Gain Level
Install Setup External Control (On, Off)Trigger 1*3Trigger
2*3Trigger 3*3 Test Picture for HDMI Out A
(4K/60Hz/4:4:4, 4K/24Hz/4:4:4, 1080p/60Hz, 480p/60Hz, Off)
Test Picture for HDMI Out B
(4K/60Hz/4:4:4*5, 4K/24Hz/4:4:4, 1080p/60Hz, 480p/60Hz, Off)
Save/Load*3Settings Lock*3 (On, Off)
Easy Setup Auto Calibration*3Internet Setup*3
*1 You can select the following inputs in the Input Setup
screen. BD/DVD, SAT/CATV, GAME, STB, VIDEO, AUX, TV, SA-CD/CD
*2 You can set up each input using these menu items in [Input
Setup].*3 Detailed information of these menu items is displayed
after you select the settings.*4 The menu item can be adjusted
against each speaker.*5 This parameter cannot be selected when
[Zone2] is selected for [HDMI OUT B Mode].
-
7GB
Table of Contents
Map of GUI Menu System
................................................................................................
2Using the home menu
......................................................................................
2
PreparationsPreparing the receiver
......................................................................................................8
Outline dimensional drawing
...........................................................................8Attaching/removing
the front cover
................................................................8
Mounting the receiver using the rack mount kit
.............................................................9
ConnectionsConnecting a 4K TV that supports HDCP 2.2 and a 4K
streaming box
using a 4K-compatible HDMI cable
...........................................................................
10
Connecting a device that supports high bandwidth video formats
.............................. 11
Making a connection for PoE (Power over Ethernet)
..................................................... 11
Making a multi-zone connection
....................................................................................12
Speaker patterns and terminals to be connected
..........................................................13
SettingsSetting up the receiver
...................................................................................................
18
Activating the network standby mode
..........................................................
18Turning on the control mode to make an external controller
connection .... 18Outputting a test tone from each speaker
(Test Tone) .................................. 18Displaying a
test screen (Test Picture)
...........................................................
18Adjusting the sound balance automatically (Auto Calibration)
.................... 18List of messages after Auto Calibration
measurements ............................... 19Saving/loading
settings of the receiver
........................................................ 19Linking
with a Hi-Fi music system
..................................................................20Mixing
separate audio/video inputs (Last video mode)
...............................20Setting the in-ceiling speaker
mode
..............................................................20Updating
the software via the network
..........................................................21Updating
the software with a USB flash drive
................................................21Setting up
through a web browser
.................................................................21Using
the PING button
....................................................................................21When
using a TV compatible with Dolby Digital Plus output
....................... 22Configuring the receiver to allow a
Crestron Control System to control the
receiver
....................................................................................................
22
Using the hidden commandsPerforming commands using the receiver
....................................................................
23
Performing commands using the supplied remote control
......................................... 23Changing the remote
control code
...............................................................
23Turning on transmitting mode of the discrete code for the main
zone ........24Turning on transmitting mode of the discrete code
for Zone 2/Zone 3 ...... 25
Useful informationZone distribution
............................................................................................................26
-
8GB
Preparations
Preparing the receiver
Outline dimensional drawing
Top
Front Side
174
mm
(6 7
/8 in
)
430 mm (17 in) 378 mm (15 in)
410 mm (16 1/4 in)
10 mm (13/32 in)
Attaching/removing the front coverThe front cover can be
completely removed from the receiver.
Remove the front cover by inserting your fingers under the
cover.
-
9GB
P
rep
aration
s
Mounting the receiver using the rack mount kitMake sure to use a
“WS-RE1” dedicated rack mount kit for this receiver when mounting
the receiver on a rack mount.
1 Check that all parts are included.Bracket × 2
Insulator
Blank panel × 1
Insulator
Screw +P U10-32×3/4 (inch)* × 6
Screw +T M5×18 (mm)*× 6
* Select the correct screws according to the type of rack.
Washer × 6
2 Remove screws from the right side of the receiver. Do not
remove screws other than those specified.
3 Mount the bracket on the right side of the receiver in the
order of the step numbers printed on the bracket using the screws
removed in step 2.
4 Repeat steps 2 and 3 for the left side to mount the
bracket.
5 Mount the receiver to the rack system. Make sure to perform
this step with more than one person.
Rack mount
6 Mount the blank panel. (The blank panel hides the legs of the
receiver to give it a cleaner look. Aligning the height of the
receiver and blank panel lets it fit into a 4U size space.)
-
10GB
Connections
Connecting a 4K TV that supports HDCP 2.2 and a 4K streaming box
using a 4K-compatible HDMI cableTo enjoy audio from 4K content such
as 4K movies, connect the HDMI output/input jacks of each device
that supports HDCP 2.2* using HDMI cables, as illustrated
below.
* HDCP 2.2 (High‐bandwidth Digital Content Protection System
Revision 2.2) is newly enhanced copyright protection technology
that is used to protect content such as 4K movies from Studios.
4K media player 4K TV or 4K projector
Connect the receiver to a 4K media player using a High Speed
HDMI cable (not supplied).
Connect the receiver to your 4K TV using a High Speed HDMI cable
(not supplied).
If you are using an FMP‐X10/X5 Media Player:Connect the cable to
the HDMI OUT 1 (for AUDIO VIDEO) jack of the player.Select [
(Settings)] ‐ [Sound] ‐ [Audio from HDMI OUT] ‐ [HDMI OUT 1] in the
Home menu of the FMP-X10/X5 Media Player after Initial Setup is
complete.
If you are using a different 4K media player:Connect the cable
to one of the HDCP 2.2-compatible HDMI output jacks. For details,
refer to the operating instructions supplied with your player.
If you are using a BRAVIA TV with the series name X950B, X900B
or X850B: Connect the cable to the HDMI IN 1 jack of your TV.
If you are using a different 4K TV or 4K projector:Connect to
one of the HDCP 2.2-compatible HDMI input jacks. If the jack is not
compatible with the ARC (Audio Return Channel) function, also
connect an optical digital cable. For details, refer to the
operating instructions supplied with your 4K TV or 4K
projector.
Note•Sony recommends that you use an HDMI-authorized cable or
HDMI cable made by Sony.
-
11GB
Co
nn
ectio
ns
Connecting a device that supports high bandwidth video
formatsWhen you use high bandwidth video formats such as 4K/60p
YCbCr 4:4:4/YCbCr 4:2:2/RGB 4:4:4 or 4K/60p YCbCr 4:2:0 Deep
Color (Deep Colour) (10 bit or 12 bit), be sure to set [HDMI Signal
Format].
1 Select [Setup] - [HDMI Setup] - [HDMI Signal Format] from the
home menu.2 Select the HDMI input you want to apply the setting.3
Select [Enhanced format].Notes•For details on the high bandwidth
video format, refer to the Help Guide.•When [Enhanced format] is
selected, we recommend to use a Premium High Speed HDMI Cable
with
Ethernet, which can support bandwidth up to 18 Gbps.•When
[Enhanced format] is selected, some devices (cable box or satellite
box, Blu-ray Disc player, and
DVD player) may not work. In this case, select [Standard
format].•If your TV have similar menu for high bandwidth video
format, check the setting on the TV menu when
you select [Enhanced format] on this receiver. For details on
the TV menu setting, refer to the operating instructions of the
TV.
Making a connection for PoE (Power over Ethernet)The following
illustration is an example of configuration of a home network with
the receiver and a computer.
LAN cable
Modem
Wireless access point, etc.
Network camera, etc.LAN cable
LAN cable
LAN cable
Computer Router
Internet
Notes•Connect a router to one of ports 1 to 8 on the receiver
using a single LAN cable. Do not connect the
same router to the receiver using more than one LAN cable. Doing
so may cause a malfunction.•Ports No. 1 and No. 2 support PoE
(Power over Ethernet, Alternative A). If you connect a
PoE-compatible
device to one of these ports, power will be supplied to the
device from the receiver.•You can also connect a device that does
not support PoE to the PoE port.•The PoE port lights in red while
supplying power.•This receiver supports PoE Class 3.
-
12GB
Making a multi-zone connectionThis receiver allows various
multi-zone connections.
Sample setup
Output jack Connected device Connection method
HDMI OUT A TV Connection: Connect to the TV using the HDMI OUT A
jack.
Operation of the receiver: Press HDMI OUT to select HDMI A.
HDMI OUT B TV Connection: Connect to the TV using the HDMI OUT B
jack.
Setup menu: Select [Setup] - [HDMI Setup] - [HDMI Out B Mode] -
[Zone2] from the home menu. Select [Setup] - [HDMI Setup] - [Zone2
Audio Out] - [Zone2 TV + AMP] from the home menu.
SPEAKERS terminalsFRONT ACENTERSURROUND
5-channel speakers and 1 or 2 subwoofer(s)
Connection: Connect the speakers and subwoofer(s).
Setup menu: Perform Auto Calibration and set the following
settings. Select [Setup] - [Speaker Setup] - [SB Speaker Assign] -
[Zone2] from the home menu.
Tip•Select [Setup] - [Input Setup] - [In-Ceiling Speaker Mode] -
[On] when you use
the in-ceiling speakers.
SPEAKERS terminalsSURROUND BACK (FRONT B/BI-AMP/ZONE 2) (when
assigned to Zone 2)
2-channel speakers Connection: Connect Zone 2 L/R speakers.
Setup menu: Perform Auto Calibration and set the following
settings. Select [Setup] - [Speaker Setup] - [SB Speaker Assign] -
[Zone2] from the home menu.
-
13GB
Co
nn
ectio
ns
Speaker patterns and terminals to be connectedWhen you connect
speakers to the receiver, refer to the following table.You can use
the following table to confirm the speaker patterns supported by
the receiver as well as the speaker terminals to which the speakers
of each speaker pattern are to be connected.To set the speaker
pattern, select [Setup] - [Speaker Setup] - [Speaker Pattern] from
the home menu.
The abbreviations and symbol used in the list are as
follows.
FH: Front high speakersTF: Top front speakersTM: Top middle
speakersTR: Top rear speakersRH: Rear high speakers
FD: Front Dolby Atmos enabled speakersSRD: Surround Dolby Atmos
enabled speakersSBD: Surround back Dolby Atmos enabled speakers:
There are no speaker terminals that can be
assigned and output is enabled from the PRE OUT jacks only.
SB: SPEAKERS SURROUND BACK (FRONT B/BI-AMP/ZONE 2) terminals
H1: SPEAKERS HEIGHT 1 (ZONE 2) terminals
What the numbers in the speaker pattern indicate:
7 . 1 . 4Number of speakers located at listener’s level Number
of
subwoofers
Number of height or overhead (top) speakers
Speaker pattern
SPEAKERS terminals / PRE OUT jacks
Zone 2 connection*1
Front B speaker
connection*1
Bi-amplifier connection*1FRONT A CENTER SURROUND
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) (single)
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
2.0 - - - - - - - SB or H1 SB SB2.0.2 (TM) - - - - (TM) - - SB
SB SB2.0.2 (FD) - - - - (FD) - - SB SB SB2.1 - - - - - - SB or H1
SB SB2.1.2 (TM) - - - - (TM) - SB SB SB2.1.2 (FD) - - - - (FD) - SB
SB SB3.0 - - - - - - SB or H1 SB SB3.0.2 (TM) - - - (TM) - - SB SB
SB3.0.2 (FD) - - - (FD) - - SB SB SB3.1 - - - - - SB or H1 SB
SB3.1.2 (TM) - - - (TM) - SB SB SB3.1.2 (FD) - - - (FD) - SB SB
SB4.0 - - - - - - SB or H1 SB SB4.0.2 (FH) - - - (FH) - - SB SB
SB4.0.2 (TM) - - - (TM) - - SB SB SB4.0.2 (FD) - - - (FD) - - SB SB
SB4.0.2 (SRD) - - - (SRD) - - SB SB SB4.0.4 (FH+TM) - - - (FH)
(TM)*2 - SB SB SB4.0.4 (FH+TR) - - - (FH) (TR)*2 - SB SB SB4.0.4
(FH+RH) - - - (FH) (RH)*2 - SB SB SB4.0.4 (TF+TM) - - - (TF) (TM)*2
- SB SB SB4.0.4 (TF+TR) - - - (TF) (TR)*2 - SB SB SB4.0.4 (TF+RH) -
- - (TF) (RH)*2 - SB SB SB
-
14GB
Speaker pattern
SPEAKERS terminals / PRE OUT jacks
Zone 2 connection*1
Front B speaker
connection*1
Bi-amplifier connection*1FRONT A CENTER SURROUND
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) (single)
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
4.0.4 (TM+TR) - - - (TM) (TR)*2 - SB SB SB4.0.4 (TM+RH) - - -
(TM) (RH)*2 - SB SB SB4.0.4 (FD+SRD) - - - (FD) (SRD)*2 - SB SB
SB4.1 - - - - - SB or H1 SB SB4.1.2 (FH) - - - (FH) - SB SB SB4.1.2
(TM) - - - (TM) - SB SB SB4.1.2 (FD) - - - (FD) - SB SB SB4.1.2
(SRD) - - - (SRD) - SB SB SB4.1.4 (FH+TM) - - - (FH) (TM)*2 SB SB
SB4.1.4 (FH+TR) - - - (FH) (TR)*2 SB SB SB4.1.4 (FH+RH) - - - (FH)
(RH)*2 SB SB SB4.1.4 (TF+TM) - - - (TF) (TM)*2 SB SB SB4.1.4
(TF+TR) - - - (TF) (TR)*2 SB SB SB4.1.4 (TF+RH) - - - (TF) (RH)*2
SB SB SB4.1.4 (TM+TR) - - - (TM) (TR)*2 SB SB SB4.1.4 (TM+RH) - - -
(TM) (RH)*2 SB SB SB4.1.4 (FD+SRD) - - - (FD) (SRD)*2 SB SB SB5.0 -
- - - - SB or H1 SB SB5.0.2 (FH) - - (FH) - - SB SB SB5.0.2 (TM) -
- (TM) - - SB SB SB5.0.2 (FD) - - (FD) - - SB SB SB5.0.2 (SRD) - -
(SRD) - - SB SB SB5.0.4 (FH+TM) - - (FH) (TM)*2 - SB SB SB5.0.4
(FH+TR) - - (FH) (TR)*2 - SB SB SB5.0.4 (FH+RH) - - (FH) (RH)*2 -
SB SB SB5.0.4 (TF+TM) - - (TF) (TM)*2 - SB SB SB5.0.4 (TF+TR) - -
(TF) (TR)*2 - SB SB SB5.0.4 (TF+RH) - - (TF) (RH)*2 - SB SB SB5.0.4
(TM+TR) - - (TM) (TR)*2 - SB SB SB5.0.4 (TM+RH) - - (TM) (RH)*2 -
SB SB SB5.0.4 (FD+SRD) - - (FD) (SRD)*2 - SB SB SB5.1 - - - - SB or
H1 SB SB5.1.2 (FH) - - (FH) - SB SB SB5.1.2 (TM) - - (TM) - SB SB
SB5.1.2 (FD) - - (FD) - SB SB SB5.1.2 (SRD) - - (SRD) - SB SB
SB5.1.4 (FH+TM) - - (FH) (TM)*2 SB SB SB5.1.4 (FH+TR) - - (FH)
(TR)*2 SB SB SB5.1.4 (FH+RH) - - (FH) (RH)*2 SB SB SB5.1.4 (TF+TM)
- - (TF) (TM)*2 SB SB SB5.1.4 (TF+TR) - - (TF) (TR)*2 SB SB SB5.1.4
(TF+RH) - - (TF) (RH)*2 SB SB SB5.1.4 (TM+TR) - - (TM) (TR)*2 SB SB
SB5.1.4 (TM+RH) - - (TM) (RH)*2 SB SB SB5.1.4 (FD+SRD) - - (FD)
(SRD)*2 SB SB SB5.0 (SB) - - - - - H1 Not available Not
available5.0.2 (SB+FH) - - (FH) - - Only PRE OUT Not available Not
available5.0.2 (SB+TM) - - (TM) - - Only PRE OUT Not available Not
available5.0.2 (SB+FD) - - (FD) - - Only PRE OUT Not available Not
available5.0.2 (SB+SRD) - - (SRD) - - Only PRE OUT Not available
Not available5.0.4 (SB+FH+TM) - - (FH) (TM) - Only PRE OUT Not
available Not available5.0.4 (SB+FH+TR) - - (FH) (TR) - Only PRE
OUT Not available Not available5.0.4 (SB+FH+RH) - - (FH) (RH) -
Only PRE OUT Not available Not available
-
15GB
Co
nn
ectio
ns
Speaker pattern
SPEAKERS terminals / PRE OUT jacks
Zone 2 connection*1
Front B speaker
connection*1
Bi-amplifier connection*1FRONT A CENTER SURROUND
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) (single)
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
5.0.4 (SB+TF+TM) - - (TF) (TM) - Only PRE OUT Not available Not
available5.0.4 (SB+TF+TR) - - (TF) (TR) - Only PRE OUT Not
available Not available5.0.4 (SB+TF+RH) - - (TF) (RH) - Only PRE
OUT Not available Not available5.0.4 (SB+TM+TR) - - (TM) (TR) -
Only PRE OUT Not available Not available5.0.4 (SB+TM+RH) - - (TM)
(RH) - Only PRE OUT Not available Not available5.0.4 (SB+FD+SRD) -
- (FD) (SRD) - Only PRE OUT Not available Not available5.1 (SB) - -
- - H1 Not available Not available5.1.2 (SB+FH) - - (FH) - Only PRE
OUT Not available Not available5.1.2 (SB+TM) - - (TM) - Only PRE
OUT Not available Not available5.1.2 (SB+FD) - - (FD) - Only PRE
OUT Not available Not available5.1.2 (SB+SRD) - - (SRD) - Only PRE
OUT Not available Not available5.1.4 (SB+FH+TM) - - (FH) (TM) Only
PRE OUT Not available Not available5.1.4 (SB+FH+TR) - - (FH) (TR)
Only PRE OUT Not available Not available5.1.4 (SB+FH+RH) - - (FH)
(RH) Only PRE OUT Not available Not available5.1.4 (SB+TF+TM) - -
(TF) (TM) Only PRE OUT Not available Not available5.1.4 (SB+TF+TR)
- - (TF) (TR) Only PRE OUT Not available Not available5.1.4
(SB+TF+RH) - - (TF) (RH) Only PRE OUT Not available Not
available5.1.4 (SB+TM+TR) - - (TM) (TR) Only PRE OUT Not available
Not available5.1.4 (SB+TM+RH) - - (TM) (RH) Only PRE OUT Not
available Not available5.1.4 (SB+FD+SRD) - - (FD) (SRD) Only PRE
OUT Not available Not available6.0 (SB) - - - - H1 Not available
Not available6.0.2 (SB+FH) - (FH) - - Only PRE OUT Not available
Not available6.0.2 (SB+TM) - (TM) - - Only PRE OUT Not available
Not available6.0.2 (SB+FD) - (FD) - - Only PRE OUT Not available
Not available6.0.2 (SB+SRD) - (SRD) - - Only PRE OUT Not available
Not available6.0.4 (SB+FH+TM) - (FH) (TM) - Only PRE OUT Not
available Not available6.0.4 (SB+FH+TR) - (FH) (TR) - Only PRE OUT
Not available Not available6.0.4 (SB+FH+RH) - (FH) (RH) - Only PRE
OUT Not available Not available6.0.4 (SB+TF+TM) - (TF) (TM) - Only
PRE OUT Not available Not available6.0.4 (SB+TF+TR) - (TF) (TR) -
Only PRE OUT Not available Not available6.0.4 (SB+TF+RH) - (TF)
(RH) - Only PRE OUT Not available Not available6.0.4 (SB+TM+TR) -
(TM) (TR) - Only PRE OUT Not available Not available6.0.4
(SB+TM+RH) - (TM) (RH) - Only PRE OUT Not available Not
available6.0.4 (SB+FD+SRD) - (FD) (SRD) - Only PRE OUT Not
available Not available6.1 (SB) - - - H1 Not available Not
available6.1.2 (SB+FH) - (FH) - Only PRE OUT Not available Not
available6.1.2 (SB+TM) - (TM) - Only PRE OUT Not available Not
available6.1.2 (SB+FD) - (FD) - Only PRE OUT Not available Not
available6.1.2 (SB+SRD) - (SRD) - Only PRE OUT Not available Not
available6.1.4 (SB+FH+TM) - (FH) (TM) Only PRE OUT Not available
Not available6.1.4 (SB+FH+TR) - (FH) (TR) Only PRE OUT Not
available Not available6.1.4 (SB+FH+RH) - (FH) (RH) Only PRE OUT
Not available Not available6.1.4 (SB+TF+TM) - (TF) (TM) Only PRE
OUT Not available Not available6.1.4 (SB+TF+TR) - (TF) (TR) Only
PRE OUT Not available Not available6.1.4 (SB+TF+RH) - (TF) (RH)
Only PRE OUT Not available Not available6.1.4 (SB+TM+TR) - (TM)
(TR) Only PRE OUT Not available Not available6.1.4 (SB+TM+RH) -
(TM) (RH) Only PRE OUT Not available Not available6.1.4 (SB+FD+SRD)
- (FD) (SRD) Only PRE OUT Not available Not available6.0 - - - - -
H1 Not available Not available6.0.2 (FH) - - (FH) - - Only PRE OUT
Not available Not available6.0.2 (TM) - - (TM) - - Only PRE OUT Not
available Not available6.0.2 (FD) - - (FD) - - Only PRE OUT Not
available Not available6.0.2 (SRD) - - (SRD) - - Only PRE OUT Not
available Not available
-
16GB
Speaker pattern
SPEAKERS terminals / PRE OUT jacks
Zone 2 connection*1
Front B speaker
connection*1
Bi-amplifier connection*1FRONT A CENTER SURROUND
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) (single)
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
6.0.2 (SBD) - - (SBD) - - Only PRE OUT Not available Not
available6.0.4 (FH+TM) - - (FH) (TM) - Only PRE OUT Not available
Not available6.0.4 (FH+TR) - - (FH) (TR) - Only PRE OUT Not
available Not available6.0.4 (FH+RH) - - (FH) (RH) - Only PRE OUT
Not available Not available6.0.4 (TF+TM) - - (TF) (TM) - Only PRE
OUT Not available Not available6.0.4 (TF+TR) - - (TF) (TR) - Only
PRE OUT Not available Not available6.0.4 (TF+RH) - - (TF) (RH) -
Only PRE OUT Not available Not available6.0.4 (TM+TR) - - (TM) (TR)
- Only PRE OUT Not available Not available6.0.4 (TM+RH) - - (TM)
(RH) - Only PRE OUT Not available Not available6.0.4 (FD+SBD) - -
(FD) (SBD) - Only PRE OUT Not available Not available6.1 - - - - H1
Not available Not available6.1.2 (FH) - - (FH) - Only PRE OUT Not
available Not available6.1.2 (TM) - - (TM) - Only PRE OUT Not
available Not available6.1.2 (FD) - - (FD) - Only PRE OUT Not
available Not available6.1.2 (SRD) - - (SRD) - Only PRE OUT Not
available Not available6.1.2 (SBD) - - (SBD) - Only PRE OUT Not
available Not available6.1.4 (FH+TM) - - (FH) (TM) Only PRE OUT Not
available Not available6.1.4 (FH+TR) - - (FH) (TR) Only PRE OUT Not
available Not available6.1.4 (FH+RH) - - (FH) (RH) Only PRE OUT Not
available Not available6.1.4 (TF+TM) - - (TF) (TM) Only PRE OUT Not
available Not available6.1.4 (TF+TR) - - (TF) (TR) Only PRE OUT Not
available Not available6.1.4 (TF+RH) - - (TF) (RH) Only PRE OUT Not
available Not available6.1.4 (TM+TR) - - (TM) (TR) Only PRE OUT Not
available Not available6.1.4 (TM+RH) - - (TM) (RH) Only PRE OUT Not
available Not available6.1.4 (FD+SBD) - - (FD) (SBD) Only PRE OUT
Not available Not available7.0 - - - - H1 Not available Not
available7.0.2 (FH) - (FH) - - Only PRE OUT Not available Not
available7.0.2 (TM) - (TM) - - Only PRE OUT Not available Not
available7.0.2 (FD) - (FD) - - Only PRE OUT Not available Not
available7.0.2 (SRD) - (SRD) - - Only PRE OUT Not available Not
available7.0.2 (SBD) - (SBD) - - Only PRE OUT Not available Not
available7.0.4 (FH+TM) - (FH) (TM) - Only PRE OUT Not available Not
available7.0.4 (FH+TR) - (FH) (TR) - Only PRE OUT Not available Not
available7.0.4 (FH+RH) - (FH) (RH) - Only PRE OUT Not available Not
available7.0.4 (TF+TM) - (TF) (TM) - Only PRE OUT Not available Not
available7.0.4 (TF+TR) - (TF) (TR) - Only PRE OUT Not available Not
available7.0.4 (TF+RH) - (TF) (RH) - Only PRE OUT Not available Not
available7.0.4 (TM+TR) - (TM) (TR) - Only PRE OUT Not available Not
available7.0.4 (TM+RH) - (TM) (RH) - Only PRE OUT Not available Not
available7.0.4 (FD+SBD) - (FD) (SBD) - Only PRE OUT Not available
Not available7.1 - - - H1 Not available Not available7.1.2 (FH) -
(FH) - Only PRE OUT Not available Not available7.1.2 (TM) - (TM) -
Only PRE OUT Not available Not available7.1.2 (FD) - (FD) - Only
PRE OUT Not available Not available7.1.2 (SRD) - (SRD) - Only PRE
OUT Not available Not available7.1.2 (SBD) - (SBD) - Only PRE OUT
Not available Not available7.1.4 (FH+TM) - (FH) (TM) Only PRE OUT
Not available Not available7.1.4 (FH+TR) - (FH) (TR) Only PRE OUT
Not available Not available7.1.4 (FH+RH) - (FH) (RH) Only PRE OUT
Not available Not available7.1.4 (TF+TM) - (TF) (TM) Only PRE OUT
Not available Not available7.1.4 (TF+TR) - (TF) (TR) Only PRE OUT
Not available Not available7.1.4 (TF+RH) - (TF) (RH) Only PRE OUT
Not available Not available7.1.4 (TM+TR) - (TM) (TR) Only PRE OUT
Not available Not available
-
17GB
Co
nn
ectio
ns
Speaker pattern
SPEAKERS terminals / PRE OUT jacks
Zone 2 connection*1
Front B speaker
connection*1
Bi-amplifier connection*1FRONT A CENTER SURROUND
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) (single)
SURROUND BACK
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
7.1.4 (TM+RH) - (TM) (RH) Only PRE OUT Not available Not
available7.1.4 (FD+SBD) - (FD) (SBD) Only PRE OUT Not available Not
available
*1 If you are connecting speakers to SPEAKERS SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) terminals, select one of the following
three connection methods: “Zone 2 connection,” “front B speaker
connection,” or “bi-amplifier connection.”
*2 If you are connecting speakers to SPEAKERS SURROUND BACK
(FRONT B/BI-AMP/ZONE 2) terminals for Zone 2, front B speaker or
bi-amplifier connection, the SPEAKERS HEIGHT 2 terminals cannot be
used for height speakers. In this case, use the PRE OUT HEIGHT 2
jacks instead.
-
18GB
Settings
Setting up the receiver
Activating the network standby modeYou can keep the network
function active even when the receiver is in standby mode.
1 Select [Setup] - [Network Setup] - [Network Standby] from the
home menu.
2 Select [On].Note•When the receiver is in standby mode, the
(power) indicator on
the front panel lights up in amber if [Network Standby] is set
to [On].
Turning on the control mode to make an external controller
connection
You can control the receiver from external devices.
1 Select [Setup] - [Install Setup] - [External Control] from the
home menu.
2 Select [On].Note•Set [External Control] to [On] to activate
the network connection or
to activate control from an external controller connected to the
RS232C port.
Outputting a test tone from each speaker (Test Tone)
You can output a test tone from each speaker in sequence.
1 Select [Setup] - [Speaker Setup] - [Test Tone] from the home
menu.
2 Select the setting you want.OffAuto: The test tone is output
from each speaker in sequence.Front L, Center, Front R, Surround R,
Sur Back R, Sur Back*, Sur Back L, Surround L, Height1 L, Height1
R, Height2 R, Height2 L, Subwoofer: You can select which speakers
will output the test tone.
* [Sur Back] appears when only one surround back speaker is
connected.
3 Adjust the speaker level.Tips•You can set a test tone by
pressing the TEST TONE button on the
remote control. In this case, you can only use the display panel
for the operation.
•To adjust the level of all speakers at the same time, press
+/–. You can also use MASTER VOLUME on the receiver.
•The adjusted value is shown on the TV screen while
adjusting.
Displaying a test screen (Test Picture)Display a test screen for
HDMI OUT A and HDMI OUT B jacks.
1 Press TEST PICTURE on the remote control.Tips•A test picture
is output in 480p from both the HDMI OUT A and
HDMI OUT B jack. If you want to output a test picture in another
resolution, select [Setup] - [Install Setup] - [Test Picture for
HDMI Out A] or [Test Picture for HDMI Out B] from the home menu,
and then select the resolution setting you want.
•HDMI audio signals are not output while the test screen is
displayed.
Adjusting the sound balance automatically (Auto Calibration)
This receiver is equipped with a D.C.A.C. (Digital Cinema Auto
Calibration) function, which allows you to perform automatic
calibration.Auto Calibration allows you to perform automatic
calibration as follows.
– Check the connection between each speaker and the
receiver.
– Adjust the speaker level. – Measure the distance of each
speaker from your seating position.*1
– Measure the speaker size.*1 – Measure the frequency
characteristics (EQ).*1 – Measure the frequency characteristics
(Phase).*1 *2
*1 The measurement result is not utilized when [Direct] is
selected.*2 The measurement result may be not utilized, depending
on the
audio formats.
Note•The D.C.A.C. is designed to achieve proper sound balance
for your
room. However, you can adjust the speaker levels manually
according to your preference using Test Tone.
1 Set up each speaker correctly, and then connect the optimizer
microphone.
2 Select [Setup] - [Speaker Setup] - [Auto Calibration] from the
home menu.
3 Follow the instructions on the TV screen, then press to select
[Start].The measurement starts in 5 seconds.The measurement
process will take approximately 30 seconds with a test
tone.When the measurement ends, a beep sounds and the screen
switches.
4 Select the item you want.Save: Saves the measurement results
and exits the setting process.Retry: Performs the Auto Calibration
again.Discard: Exits the setting process without saving the
measurement results.
5 Save the measurement results.Select [Save] in step 4.
-
19GB
Settin
gs
Calibration MatchingWhen Auto Calibration is executed, this
function works automatically to match the distance and level of the
right and left speakers. You can set this function only after the
D.C.A.C. measurement process has been completed and the results of
D.C.A.C. measurement are saved. The setting is valid until you
change it.
Note•If an error code or warning message appears on the screen
in
step 3, see “List of messages after Auto Calibration
measurements” (page 19).
Tips•You can also perform automatic calibration by pressing the
AUTO
CAL button on the remote control. If you use the AUTO CAL
button, the following restrictions apply to the operation: – Prior
settings relating to the Auto Calibration will be skipped. – You
can only use the display panel for the operation.
•The Auto Calibration function will be canceled if you perform
the following during the measurement process: – Turn the receiver
on or off. – Press the input buttons on the remote control or on
the receiver. – Press . – Press SPEAKERS on the receiver. – Press
HDMI OUTPUT. – Press AMP MENU. – Press HOME. – Press AUTO CAL. –
Change the volume level.
List of messages after Auto Calibration measurements•Code
31:
Front speakers are not selected properly. Select the front
speakers using SPEAKERS, and then perform Auto Calibration
again.
•Code 32, Code 33: – Speakers were not detected or not connected
properly. – None of the front speakers are connected or only one
front speaker is connected.
– Either the surround left or surround right speaker is not
connected.
– A surround back speaker is connected only to the SPEAKERS
SURROUND BACK (FRONT B/BI-AMP/ZONE 2) R terminal. If connecting
only one surround back speaker, connect it to the SPEAKERS SURROUND
BACK (FRONT B/BI-AMP/ZONE 2) L terminal.
– Either the Height1 left or Height1 right speaker is not
connected.
– Either the Height2 left or Height2 right speaker is not
connected.
– The optimizer microphone is not connected. Make sure that the
optimizer microphone is connected properly, and then perform Auto
Calibration again. If the optimizer microphone is connected
properly but the error code still appears, the optimizer microphone
cable may be damaged.
•Code 34:Speakers are not placed in the proper position.
Speakers or an optimizer microphone on the right or left may be
placed wrongly. See the supplied Startup Guide and check the
speaker position.
•Code 35:The measurement result is not match to the speaker
pattern you set. See the Help Guide and change the setting to fit
the actual speaker pattern.
•Warning 40:The measurement process has been completed and a
high noise level has been detected. You may be able to achieve
better results if you try the process again in a quiet
environment.
•Warning 41, Warning 42: – The input from the optimizer
microphone is too large. – The distance between the speaker and the
microphone may be too small. Set them further apart and perform the
measurement again.
•Warning 43:The distance and position of a subwoofer cannot be
detected. This may be caused by noise. Try performing the
measurement in a quiet environment.
•Warning 44:Measurement has been completed. However the speakers
are not placed in the proper position with respect to each other.
See the supplied Startup Guide and check the relative positions of
the speakers.
•NO WARNING:There is no warning information.
Saving/loading settings of the receiver You can save the
settings to a USB flash drive and restore the saved settings to the
receiver or to another receiver of the same model.
Saving Loading
To save the settingsInsert a USB flash drive to the USB port on
the front panel of the receiver. Select [Setup] - [Install Setup] -
[Save/Load] - [Save] from the home menu.
To load the settingsInsert to the USB port on the front panel of
the receiver a USB flash drive on which the settings are
saved.Select [Setup] - [Install Setup] - [Save/Load] - [Load] from
the home menu.
-
20GB
Linking with a Hi-Fi music systemThis receiver can switch its
power and input automatically by linking with playback operation of
the Hi-Fi music system.Configure settings to enable the receiver to
operate linked with a Hi-Fi System device.
1 Select [Setup] - [Network Setup] - [Music Connect] from the
home.
2 Select the setting you want.Each of the following settings can
be selected on both Device 1 and Device 2.Connected Device: Select
the connected device to enable the function. Input for Music
Connect1 or 2: Select the input to link with.Preset Volume: Preset
the volume level.Output Zone: Select the zone to which you want to
output sound.
3 Start playback on the player device.The receiver will be
turned on and the input will be switched automatically.
To disable Music ConnectSelect [Setup] - [Network Setup] -
[Music Connect] - [Connected Device] - [Remove Connected Device]
from the home menu.
Notes•The Music Connect feature can be linked only with the
power
source and input of the main zone or Zone 2. This feature does
not link with Zone 3.
•The link feature of Music Connect may not work correctly
depending on factors such as the specifications of the connected
device.
•We recommend that you set [Network Standby] to [On] to activate
the feature for linking with Music Connect even if the receiver is
in standby mode.
Mixing separate audio/video inputs (Last video mode)
The receiver can continuously output the input video image used
most recently when an audio-only input source is selected.
1 Connect the desired background music source to an input by
analog, optical, or coaxial cable. Or use the built-in tuner.
2 Set the input to the following in the Input Setup menu.HDMI:
[None]Component: [None]Composite: [---]Audio: The input connected
to the source.When using the built-in tuner, set the screen mode to
[Simple] using the options menu in [FM/AM Display].
ExamplePress SAT/CATV followed by TUNER to listen to sound from
the built-in tuner while watching a video source connected to
SAT/CATV.The audio output changes to that of the tuner source while
SAT/CATV video output is retained.
Setting the in-ceiling speaker modeSony has developed a new
special sound mode for CI installation. This feature will virtually
relocate the front and center in-ceiling speakers down to around
the screen. That way, the customer will hear the actors’ voices
coming from the screen instead of the ceiling. This mode also makes
music sound more natural in a room with in-ceiling speakers.
1 Perform Auto Calibration.2 Select [Setup] - [Audio Setup] -
[In-Ceiling
Speaker Mode] - [Front & Center] or [Front] from the home
menu.
Notes•This mode is not available when [Pure Direct] is set to
[On].•This mode will be disabled in a speaker pattern with
Dolby
Enabled speakers.
Tips•You can select on/off for each input in Input Setup
menu.•You can also select [In-Ceiling Speaker Mode] in [Sound
Effects]
from the home menu.•You can also switch the function on/off by
pressing IN-CEILING SP
on the remote control or the receiver.•To obtain optimal effects
in the listening environment, configure
the [Ceiling Height] setting and perform Auto Calibration.
-
21GB
Settin
gs
Updating the software via the networkYou can update the receiver
software via the network.Connect the receiver to the Internet
beforehand, and then make sure [Internet Connection] is displayed
as [OK] in the [Network Information] menu.
1 Select [Setup] - [System Setup] from the home menu.
2 Select [Network Update].3 Follow the instructions on the TV
screen
[UPDATING…XXX%] will be displayed on the frontdisplay. The
receiver will automatically reboot after theupdate completes.
Updating the software with a USB flash driveMake sure to perform
the following steps when a software update is delivered.You can
download the update software from the following
website.https://www.sony.com/am/support
Saving
New software
Updating
1 Copy the file for updating to the top level directory (just
under the root directory) of the USB flash drive (FAT16 or FAT32
with more than 100 MB of free space).
2 Turn the receiver on.3 Insert the USB flash drive into the USB
port on
the front panel of the receiver.
4 Select [Setup] - [System Setup] - [USB Update] from the home
menu.[UPDATING…XXX%] will be displayed on the front display. The
receiver will automatically reboot after the update completes.
Note•It takes up to 100 minutes for the update to
complete.
Setting up through a web browserThe receiver provides a web
browser interface for configuring settings.The PING feature is
useful for checking your IP address quickly.
Open a web browser on your computer or mobile device on the same
network with the receiver, and then access http://[receiver’s
ip-address]/
Using the PING button The receiver provides the following
functions simply by pressing the PING button on the front panel of
the receiver.
The receiver sends specific UDP multicast or broadcast packets
to establish a network connection.
Protocol Protocol owner
SDDP Control4
The receiver displays its IP information on the front display as
follows.
Information
1 IP address
2 MAC address
-
22GB
When using a TV compatible with Dolby Digital Plus output
The receiver can receive Dolby Atmos signals sent from a TV or
other connected devices. Since Dolby Atmos signals from the TV are
sent in Dolby Digital Plus format, ARC (Audio Return
Channel)-compatible HDMI jacks must be connected using an HDMI
cable instead of an optical digital cable.Normally, it would be
necessary to turn on the Control for HDMI function for both
receiver and TV in order to use the Audio Return Channel (ARC). In
this case, however, the link function between the receiver, TV and
other devices is also activated. Therefore, in order to facilitate
the operation of the controller in a custom installation (where the
entire system is controlled via the controller), this receiver is
designed to activate the ARC function separately, even if the
Control for HDMI function is turned off.As a result, Dolby
Atmos-compatible content sent from the TV can be played back
through an ARC-compatible HDMI jack, without the need to activate
the link function using the Control for HDMI function.Since the ARC
function can still be used as before, Dolby Atmos-compatible
content can be played back in high quality, even if the Control for
HDMI function for the TV or connected devices is turned on.If you
use a TV compatible with Dolby Digital Plus output, perform the
following settings on the receiver in order to play back Dolby
Atmos-compatible content sent from the TV.
1 Turn on the Control for HDMI function on the TV.The ARC output
from the TV will be enabled.
2 Set the Dolby Digital Plus output of the TV to enable it.Dolby
Atmos output from the TV will be enabled.
3 Select [Setup] – [HDMI Setup] – [Audio Return Channel] – [On]
on the receiver.ARC signals from the TV can now be received.
4 Select [Setup] – [Input Setup] – [Input Mode] – [Auto] on the
receiver.
5 Press HDMI OUT to select [HDMI OUT A].6 Turn off the Control
for HDMI function for all
devices connected to the receiver except the TV.
7 Turn off any settings for the operation of other devices on
the TV’s remote control.
8 Switch the input of the receiver to [TV].
Configuring the receiver to allow a Crestron Control System to
control the receiver
This receiver is certified as Crestron Connected. You can
therefore allow a Crestron Control System to control the receiver
collectively as part of a home automation system by configuring the
receiver as follows.This operation can only be performed using the
buttons and display panel on the front of the receiver. You will
also need to connect the receiver to a network.
1 Turn on the receiver.2 Press AMP MENU.3 Press / repeatedly to
select [3. NETWORK
SETUP], and then press ENTER.
4 Press / repeatedly to select [3.5. CRESTRONCONNECTED SETUP],
and then press ENTER.
5 Input the following items. –3.5.2. IP ADDRESS (the
controller’s IP address) –3.5.3. PORT (“41794” is set as the
default.) –3.5.4. IPID* (the controller’s IPID)
* Input the values as hexadecimal numbers. Press / repeatedly to
select each item, and then
press ENTER. Press / repeatedly to select a digit and press
/ repeatedly to change the digit. Press ENTER to confirm the
value.
If you want to re-input the values, press RETURN and then repeat
the steps starting from .
6 Press / repeatedly to select [3.5.1. CRESTRON CONNECTED], and
then press ENTER.
7 Press / repeatedly to select [ON], and then press ENTER.
If you have already configured the receiver’s network settings,
you can also configure the above settings from a web browser.Open a
web browser on a computer or mobile device connected to the same
network as the receiver, and then access the following
URL.http://[receiver’s IP address]/
-
23GB
Usin
g th
e h
idd
en
com
man
ds
Using the hidden commands
Performing commands using the receiverThis receiver allows you
to perform various commands using buttons on the front panel.
PING ENTERAMP
MENU 2CH/DIRECT MULTI ST.
Function Operation
User initialize (Memory Clear) Hold for 5 seconds in
standby mode.
Sound Field Clear Hold down MULTI.ST. and press in standby
mode.
Settings Lock Hold down PING and AMP MENU and press ENTER while
the receiver is turned on.
Command mode(Remote Controller)
Hold down 2CH/DIRECT and press in standby mode.
Performing commands using the supplied remote controlThis
receiver allows you to perform various commands using the supplied
remote control.
Changing the remote control code
1 While holding down MAIN, press MAIN . MAIN will start
flashing.
2 Press CUSTOM PRESET 1 or 2 to select AV1 or AV2 as needed.MAIN
will stop flashing and light up in red.
3 Press .MAIN will start flashing again.
4 Press again to set the command mode.
-
24GB
Turning on transmitting mode of the discrete code for the main
zone
While holding down MAIN, press INPUT MODE on the remote control
for 5 seconds.Transmitting mode of the discrete code for the
main zone is activated when MAIN starts flashing.
Command list in transmitting mode of the discrete code for the
main zone
Key name Transmitting mode of the discrete code (main)
Code name
HDMI OUTPUT HDMI OUTPUT
ZONE2 POWER ON (ZONE2)
ZONE3 POWER ON (ZONE3)
MAIN POWER ON
ZONE 2 (illuminated in red)
ZONE 2
ZONE 3 (illuminated in red)
ZONE 3
MAIN (illuminated in red)
MAIN
BD/DVD 1
SAT/CATV 2
GAME 3
STB 4
VIDEO 5
AUX 6
TV 7
SA-CD/CD 8
TUNER 9
SOUND OPTIMIZER 10/0
PURE DIRECT 11/*
IN-CEILING SP MODE 12/#
CUSTOM PRESET 1 PARTY MODE ON/OFF
CUSTOM PRESET 2 ZONE 2 PARTY MODE
CUSTOM PRESET 3 ZONE 3 PARTY MODE
CUSTOM PRESET 4 ZONE 2+3 PARTY MODE
DISPLAY HDMI OUTPUT A
Key name Transmitting mode of the discrete code (main)
Code name
AMP MENU HDMI OUTPUT B
RETURN HDMI OUTPUT A+B
OPTIONS HDMI OUTPUT OFF
–
HOME SYSTEM POWER OFF
INPUT SETUP SF 2CH STEREO
TEST PICTURE POWER OFF (ZONE2)
TEST TONE POWER OFF (ZONE3)
AUTO CAL POWER OFF
2CH/DIRECT FRONT SPEAKER OFF
A.F.D. FRONT SPEAKER A
MOVIE FRONT SPEAKER B
MULTI ST. FRONT SPEAKER A+B
TUNING + –
MEMORY –
PRESET + –
TUNING – TV HDMI1
FM TV HDMI2
AM TV HDMI3
PRESET – TV HDMI4
TV OFF
+ MUTING OFF
– MUTING ON
INPUT + FUNCTION +
INPUT – FUNCTION –
INPUT MODE TV ON
To deactivate transmitting mode of the discrete code for the
main zoneWhile holding down MAIN, press INPUT MODE on the remote
control for 5 seconds.Transmitting mode of the discrete code for
the main zone is deactivated when MAIN stops flashing.
Note•Transmitting mode of the discrete code for the main zone is
cancelled automatically when you do not
press any key more than 10 minutes.
-
25GB
Usin
g th
e h
idd
en
com
man
ds
Turning on transmitting mode of the discrete code for Zone
2/Zone 3
Press ZONE2 or ZONE3 on the remote control when transmitting
mode of the discrete code for the main zone is active.Transmitting
mode of the discrete code for Zone 2/Zone 3 is activated when the
selected zone button start flashing.
Command list in transmitting mode of the discrete code for Zone
2/Zone 3
Key name Transmitting mode of the discrete code (Zone 2)
Transmitting mode of the discrete code (Zone 3)
Code name Code name
HDMI OUTPUT POWER OFF POWER OFF
ZONE2 — —
ZONE3 — —
MAIN POWER ON POWER ON
ZONE 2 (illuminated in red)
ZONE 2 ZONE 2
ZONE 3 (illuminated in red)
ZONE 3 ZONE 3
MAIN (illuminated in red)
MAIN MAIN
BD/DVD 1 1
SAT/CATV 2 2
GAME 3 3
STB 4 4
VIDEO 5 5
AUX 6 6
TV 7 7
SA-CD/CD 8 8
TUNER 9 9
SOUND OPTIMIZER 10/0 10/0
PURE DIRECT 11/* 11/*
IN-CEILING SP MODE 12/# 12/#
CUSTOM PRESET 1 — —
CUSTOM PRESET 2 — —
CUSTOM PRESET 3 — —
CUSTOM PRESET 4 — —
DISPLAY — —
AMP MENU — —
RETURN — —
OPTIONS — —
— —
— —
— —
— —
— —
SP SETUP — —
HOME — —
INPUT SETUP — —
TEST PICTURE — —
Key name Transmitting mode of the discrete code (Zone 2)
Transmitting mode of the discrete code (Zone 3)
Code name Code name
TEST TONE — —
AUTO CAL — —
2CH/DIRECT — —
A.F.D. — —
MOVIE — —
MULTI ST. — —
TUNING + — —
MEMORY — —
PRESET + — —
TUNING – — —
FM — —
AM — —
PRESET – — —
MUTING MUTING
+ MUTING OFF MUTING OFF
– MUTING ON MUTING ON
INPUT + FUNCTION + FUNCTION +
INPUT – FUNCTION – FUNCTION –
INPUT MODE — —
-
26GB
Useful information
Zone distributionThe receiver can deliver input signals for each
video or audio input to another zone in combinations such as the
following.
Zone distribution capability (video)
Video input Main zoneHDMI OUT A
Main zoneHDMI OUT B*1
Zone 2HDMI OUT B*2
Main zoneVIDEO OUT MONITOR (Composite)
Zone 2 VIDEO OUT ZONE 2 (Composite)
VIDEO IN jacks (composite) *3
COMPONENT VIDEO IN jacks (component)
*3 – –
HDMI IN jacks*5 *6 –*4 –*4
*1 When [HDMI Out B Mode] in the [HDMI Setup] menu is set to
[Main].*2 When [HDMI Out B Mode] in the [HDMI Setup] menu is set to
[Zone2].*3 The receiver cannot output a different analog signal to
the Zone 2 HDMI OUT jack while an analog
signal of the main zone is being output from the HDMI OUT A
jack.*4 HDMI down converting is prohibited by HDMI guidelines.*5
HDMI IN 1, 2, 3, 4, and 5 jacks support bandwidths of up to 18
Gbps, and HDMI IN 6 (GAME) jack
supports bandwidths of up to 9 Gbps.*6 Zone 2 HDMI OUT jack
supports bandwidths of up to 9 Gbps.
Zone distribution capability (audio)
Input source / Output
Main zone HDMI OUT A
Main zoneHDMI OUT B
Zone 2HDMI OUT B
Main zone SPEAKERS terminals
Zone 2 SPEAKERS terminals
Zone 2 AUDIO OUT (Fixed/Variable)
Zone 3 AUDIO OUT (Fixed/Variable)
Multi Ch PRE OUT
AUDIO IN jacks (RCA)
– –
Built-in Tuner*1 – –
DIGITAL OPTICAL IN jacks
– – *2 *2 *2 –
DIGITAL COAXIAL IN jack
– – *2 *2 *2 –
HDMI IN jacks *3 *3 –
*1 When [FM TUNER] or [AM TUNER] is selected at the same time in
the main zone and Zone 2 or Zone 3, the item most recently selected
will be set.
*2 Digital audio stream is not supported for distributing
signals such as Dolby Digital and DTS. The Digital Audio output
setting should be “2ch PCM” on the player device.
*3 Zone 2 speaker out and Zone 2 audio out only support
2-channel audio output. Multi-channel stream signals are
automatically converted to 2 channels signals, and then output to
Zone 2 if the same source signals as the main zone are selected in
Zone 2.
-
27GB
U
sefu
l info
rmatio
n
-
2FR
Carte du système de l’IGU
Utilisation du menu d’accueil
Les options de menu soulignées correspondent aux paramètres par
défaut.
HomeWatch BD/DVD
SAT/CATVGAMESTBVIDEOTV
Listen AUXSA‐CD/CDFM TUNERAM TUNER
Custom Preset MovieMusicPartyNight
Sound Effects Sound Field 2ch StereoDirectAuto Format
DecodingDolby SurroundNeural:XMulti Stereo
EqualizerSound Optimizer Normal
LowOff
In‐Ceiling Speaker Mode Front & CenterFrontOff
Pure Direct OnOff
-
3FR
Zone Controls Zone2 Power OnOff
Zone2 Input SOURCEBD/DVDSAT/CATVGAMESTBVIDEOAUXTVSA-CD/CDFM
TUNERAM TUNER
Zone2 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
Zone3 Power OnOff
Zone3 Input SOURCEVIDEOAUXTVSA-CD/CDFM TUNERAM TUNER
Zone3 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
-
4FR
Setup Input Setup*1 *2
IconNameWatch/ListenShow/HideHDMIOPTICAL/COAXIALCOMPONENTVIDEO
INAUDIO INInput ModePreset Sound FieldIn-Ceiling Speaker ModeA/V
SyncSubwoofer Low Pass FilterSubwoofer LevelPreset Gain
LevelTrigger 1Trigger 2Trigger 3
Speaker Setup Auto Calibration*3Automatic Phase Matching (Auto,
Off)Calibration Type (Full Flat, Engineer, Front Reference,
Off)Speaker PatternSpeaker ConnectionsSB Speaker Assign (Zone2,
Bi-Amp, Front B, Off)Height1 SP Assign (Zone2, Off)Size*4 (Large,
Small)Distance*4 (32 ft 9 in, 32 ft 8 in, …,
9 ft 10 in, …,
6 ft 7 in, 6 ft 6 in)Level*4 (+10.0dB,
+9.5dB, …, 0.0dB, …, –9.5dB,
–10.0dB)Test Tone*3Crossover Frequency*4 (40Hz, 50Hz, …, 120Hz,
…, 190Hz, 200Hz)Equalizer*4 (+10.0dB, +9.0dB, …, 0.0dB, …,
–9.0dB,
–10.0dB)Center Speaker Lift Up (10, 9, 8, …, 2, 1, Off)Surround
Speaker Position (Front, Back)Speaker Relocation (Type A, Type B,
Off)Ceiling Height (32 ft 9 in, 32 ft 8 in, …,
9 ft 0 in, …,
6 ft 7 in, 6 ft 6 in)Speaker Impedance
(8Ω, 4Ω)Distance Unit (feet, meter)
Network Setup Internet Setup*3Information*3Network Standby (On,
Off)Music Connect Device1 Connected Device
Input for Music Connect1
Preset VolumeOutput Zone
Device2 Connected DeviceInput for Music Connect2Preset
VolumeOutput Zone
-
5FR
Setup Audio Setup Digital Legato Linear (Auto 1, Auto 2,
Off)Sound Optimizer (Normal, Low, Off)Sound Field*3In-Ceiling
Speaker Mode (Front & Center, Front, Off)Pure Direct (On,
Off)Subwoofer Low Pass Filter (On, Off)A/V Sync (300 ms,
290 ms, …, 10 ms, 0 ms,
HDMI Auto)Dual Mono (Main, Sub, Main/Sub)Dynamic Range
Compressor
(Auto, On, Off)
Neural:X (On, Off)
HDMI Setup 4K Scaling (Auto, Off)Control for HDMI (On,
Off)Standby Linked to TV (Auto, On, Off)Audio Return Channel (On,
Off)Pass Through (Auto, On, Off)Audio Out (AMP, TV+AMP)Zone2 Audio
Out (AMP, Zone2 TV+AMP, Zone2 AMP)Subwoofer Level (Auto, +10dB,
0dB)HDMI Out B Mode (Main, Zone2)Priority (Main&Zone2, Main
Only)Fast View (Auto, Off)HDMI Signal Format HDMI IN 1 (Standard
format,
Enhanced format)HDMI IN 2 (Standard format,
Enhanced format)HDMI IN 3 (Standard format,
Enhanced format)HDMI IN 4 (Standard format,
Enhanced format)HDMI IN 5 (Standard format,
Enhanced format)
Zone Setup Zone Controls Zone2 Power (On, Off)Zone2 Input
(SOURCE, BD/DVD, …,
FM TUNER, AM TUNER)
Zone2 Volume (+23.0dB, +22.5dB, …, –40.0dB, …, –92.0dB,
–∞dB)
Zone3 Power (On, Off)Zone3 Input (SOURCE, VIDEO, …,
FM TUNER, AM TUNER)Zone3 Volume (+23.0dB, +22.5dB, …,
–40.0dB, …, –92.0dB, –∞dB)
Main Preset Volume (+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Main
Max Volume (+23.0dB, +22.5dB, ..., –40.0dB)Zone2 Preset Volume
(+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Zone2 Max Volume (+23.0dB,
+22.5dB, ..., –40.0dB)Zone2 Line Out (Variable, Fixed)Zone3 Preset
Volume (+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)Zone3 Max Volume
(+23.0dB, +22.5dB, ..., –40.0dB)Zone3 Line Out (Variable,
Fixed)
-
6FR
Setup System Setup Language (English, Español, Français)Auto
Display (On, Off)Auto Standby (On, Off)Volume Display (Relative,
Absolute)Dimmer (Bright, Dark, Off)Sleep (2:00:00, 1:30:00,
1:00:00, 0:30:00, Off)Software VersionNetwork UpdateUSB
Update*3Tuner Setup*3 FM Mode
Name InputPreset Gain Level
Install Setup External Control (On, Off)Trigger 1*3Trigger
2*3Trigger 3*3 Test Picture for HDMI Out A
(4K/60Hz/4:4:4, 4K/24Hz/4:4:4, 1080p/60Hz, 480p/60Hz, Off)
Test Picture for HDMI Out B
(4K/60Hz/4:4:4*5, 4K/24Hz/4:4:4, 1080p/60Hz, 480p/60Hz, Off)
Save/Load*3Settings Lock*3 (On, Off)
Easy Setup Auto Calibration*3Internet Setup*3
*1 Vous pouvez sélectionner les entrées suivantes sur l’écran
Input Setup. BD/DVD, SAT/CATV, GAME, STB, VIDEO, AUX, TV,
SA-CD/CD
*2 Vous pouvez sélectionner chaque entrée à l’aide de ces
options de menu dans [Input Setup].*3 Les informations détaillées
de ces options de menu s’affichent après que vous avez sélectionné
les réglages.*4 Il est possible de régler l’option de menu pour
chaque enceinte.*5 Il est impossible de sélectionner ce paramètre
lorsque [HDMI OUT B Mode] est réglé sur [Zone2].
-
7FR
Table des matièresCarte du système de l’IGU
...............................................................................................
2
Utilisation du menu d’accueil
...........................................................................
2
PréparationsPréparation de
l’ampli-tuner............................................................................................8
Plan d’encombrement
......................................................................................8Fixation/retrait
du capot avant
.........................................................................8
Montage de l’ampli-tuner à l’aide du kit de montage sur bâti
......................................9
RaccordementsRaccordement d’un téléviseur 4K prenant en charge
HDCP 2.2 et d’un décodeur de
flux 4K à l’aide d’un câble HDMI compatible 4K
....................................................... 10
Raccordement d’un appareil prenant en charge des formats vidéo à
haute bande passante
......................................................................................................................
11
Établissement d’une connexion pour PoE (Power over Ethernet)
................................. 11
Établissement d’une connexion sur plusieurs zones
.....................................................12
Modèles d’enceintes et bornes à raccorder
...................................................................13
RéglagesRéglage de l’ampli-tuner
...............................................................................................
19
Activation du mode veille du
réseau..............................................................
19Activation du mode de commande pour établir une connexion de
commande externe
.................................................................................
19Reproduction d’une tonalité de test depuis chacune des
enceintes
(Test Tone)
...............................................................................................
19Affichage d’une mire (Test Picture)
................................................................
19Réglage automatique de la balance du son (Auto Calibration)
.................... 19Liste des messages qui s’affichent après les
mesures de calibrage
automatique
............................................................................................20Enregistrement/chargement
des réglages sur l’ampli-tuner
.......................20Raccordement sur une chaîne Hi-Fi
................................................................21Mixage
d’entrées audio/vidéo distinctes (dernier mode vidéo)
....................21Réglage du mode d’enceintes au plafond
......................................................21Mise à jour
du logiciel via le réseau
...............................................................
22Mise à jour du logiciel à l’aide d’une clé USB
................................................ 22Configuration
via un navigateur Web
............................................................
22Utilisation de la touche PING
.........................................................................
22Utilisation d’un téléviseur compatible avec une sortie Dolby
Digital Plus ... 23Configuration de l’ampli-tuner pour permettre à
un système de contrôle
Crestron de contrôler l’ampli-tuner
........................................................ 23
Utilisation des commandes cachéesExécution de commandes à l’aide
de l’ampli-tuner
.....................................................24
Exécution de commandes à l’aide de la télécommande fournie
.................................24Changement du code de la
télécommande
.................................................24Activation du
mode de transmission du code discret pour la zone principale ...
25Activation du mode de transmission du code discret pour la Zone
2/Zone 3 ...26
Informations utilesDistribution des zones
...................................................................................................
27
-
8FR
Préparations
Préparation de l’ampli-tuner
Plan d’encombrement
Haut
Avant Côté
174
mm
(6 7
/8 p
o)
430 mm (17 po) 378 mm (15 po)
410 mm (16 1/4 po)
10 mm (13/32 po)
Fixation/retrait du capot avantVous pouvez retirer complètement
le capot avant de l’ampli-tuner.
Retirez le capot avant en insérant les doigts sous le capot.
-
9FR
P
rép
aration
s
Montage de l’ampli-tuner à l’aide du kit de montage sur
bâtiAssurez-vous d’utiliser un kit de montage sur bâti « WS-RE1 »
dédié à cet ampli-tuner lorsque vous le montez sur un bâti.
1 Vérifiez que toutes les pièces sont fournies.Support × 2
Isolateur
Panneau blanc × 1
Isolateur
Vis +P U10-32×3/4 (pouce)* × 6
Vis +T M5×18 (mm)*× 6
* Sélectionnez les vis adaptées au type de bâti.
Rondelle × 6
2 Ôtez les vis du côté droit de l’ampli-tuner. N’ôtez pas
d’autres vis que celles indiquées.
3 Montez le support du côté droit de l’ampli-tuner dans l’ordre
des numéros d’étape imprimés sur celui-ci à l’aide des vis retirées
à l’étape 2.
4 Répétez les étapes 2 et 3 sur le côté gauche pour monter le
support.
5 Montez l’ampli-tuner sur le système de bâti. Veillez à
effectuer cette étape avec plus d’une personne.
Montage sur bâti
6 Montez le panneau blanc. (Le panneau blanc cache les pieds de
l’ampli-tuner pour des raisons esthétiques. L’alignement de la
hauteur de l’ampli-tuner et du panneau blanc permet de le loger
dans un espace d’une taille 4U.)
-
10FR
Raccordements
Raccordement d’un téléviseur 4K prenant en charge HDCP 2.2 et
d’un décodeur de flux 4K à l’aide d’un câble HDMI compatible 4KPour
profiter de contenus audio 4K, tels que des films 4K, raccordez les
prises de sortie/entrée HDMI de chaque appareil prenant en charge
HDCP 2.2* à l’aide de câbles HDMI, comme illustré ci-dessous.
* HDCP 2.2 (High‐bandwidth Digital Content Protection System
Revision 2.2) est une nouvelle technologie améliorée de protection
des droits d’auteur utilisée pour protéger du contenu tel que des
films 4K de studios.
Lecteur multimédia 4K Téléviseur 4K ou projecteur 4K
Raccordez l’ampli-tuner sur un lecteur multimédia 4K à l’aide
d’un câble High Speed HDMI (non fourni).
Raccordez l’ampli-tuner sur votre téléviseur 4K à l’aide d’un
câble High Speed HDMI (non fourni).
Si vous utilisez un lecteur multimédia FMP‐X10/X5 :Raccordez le
câble à la prise HDMI OUT 1 (for AUDIO VIDEO) du
lecteur.Sélectionnez [ (Réglages)] ‐ [Son] ‐ [Sortie audio HDMI
OUT] ‐ [HDMI OUT 1] dans le menu d’accueil du lecteur multimédia
FMP-X10/X5 une fois la configuration initiale terminée.
Si vous utilisez un lecteur multimédia 4K différent :Raccordez
le câble sur l’une des prises de sortie HDMI compatibles HDCP 2.2.
Pour des informations détaillées, reportez-vous au mode d’emploi du
lecteur.
Si vous utilisez un téléviseur BRAVIA dont le nom de série est
X950B, X900B ou X850B : Raccordez le câble sur la prise HDMI
IN 1 du téléviseur.
Si vous utilisez un téléviseur 4K différent ou un projecteur 4K
:Raccordez l’une des prises d’entrée HDMI compatibles
HDCP 2.2. Si la prise n’est pas compatible avec la fonction
ARC (Audio Return Channel), raccordez également un câble optique
numérique. Pour en savoir plus, reportez-vous au mode d’emploi
fourni avec votre téléviseur 4K ou projecteur 4K.
Remarque•Sony vous recommande d’utiliser un câble agréé HDMI ou
un câble HDMI fabriqué par Sony.
-
11FR
Racco
rde
me
nts
Raccordement d’un appareil prenant en charge des formats vidéo à
haute bande passanteLorsque vous utilisez des formats vidéo à haute
bande passante comme 4K/60p YCbCr 4:4:4/YCbCr 4:2:2/RGB 4:4:4
ou 4K/60p YCbCr 4:2:0 Deep Color (Deep Colour) (10 ou 12 bits),
veillez à régler [HDMI Signal Format].
1 Sélectionnez [Setup] - [HDMI Setup] - [HDMI Signal Format]
dans le menu d’accueil.
2 Sélectionnez l’entrée HDMI à laquelle vous souhaitez appliquer
le paramètre.3 Sélectionnez [Enhanced format].Remarques•Pour en
savoir plus sur le format vidéo à haute bande passante, consultez
le Guide d’aide.•Lorsque [Enhanced format] est sélectionné, nous
conseillons d’utiliser un câble HDMI haute vitesse avec
Ethernet, qui peut prendre en charge une bande passante jusqu’à
18 Gbits/s.•Lorsque [Enhanced format] est sélectionné, certains
périphériques (décodeurs câble ou décodeurs
satellite, lecteurs Blu-ray Disc et lecteurs DVD) peuvent mal
fonctionner. Le cas échéant, sélectionnez [Standard format].
•Si votre téléviseur possède un menu similaire pour le format
vidéo à haute bande passante, vérifiez le réglage sur le menu du
téléviseur lorsque vous sélectionnez [Enhanced format] sur cet
ampli-tuner. Pour en savoir plus sur le réglage du menu du
téléviseur, reportez-vous à son mode d’emploi.
Établissement d’une connexion pour PoE (Power over
Ethernet)L’illustration suivante est un exemple de configuration
d’un réseau domestique avec l’ampli-tuner et un ordinateur.
Câble LAN
Modem
Point d’accès sans fil, etc.
Caméra réseau, etc.Câble LAN
Câble LAN
Câble LAN
Ordinateur Routeur
Internet
Remarques•Raccordez un routeur à l’un des ports 1 à 8 de
l’ampli-tuner à l’aide d’un câble LAN. Ne connectez pas le
même routeur sur l’ampli-tuner à l’aide de plus d’un câble LAN.
Cela pourrait provoquer un dysfonctionnement.
•Les ports n° 1 et n° 2 prennent en charge PoE (Power over
Ethernet, Alternative A). Si vous raccordez à un appareil
compatible PoE sur l’un de ces ports, l’alimentation est fournie à
l’appareil à partir de l’ampli-tuner.
•Vous pouvez également raccorder un appareil qui ne prend pas en
charge PoE sur le port PoE.•Le port PoE s’allume en rouge lorsqu’il
fournit l’alimentation.•Cet ampli-tuner prend en charge PoE, classe
3.
-
12FR
Établissement d’une connexion sur plusieurs zonesCet ampli-tuner
autorise des connexions sur plusieurs zones.
Exemple de configuration
Prise de sortie Appareil raccordé Méthode de raccordement
HDMI OUT A Téléviseur Raccordement : Raccordez au téléviseur via
la prise HDMI OUT A.
Fonctionnement de l’ampli-tuner : Appuyez sur HDMI OUT pour
sélectionner HDMI A.
HDMI OUT B Téléviseur Raccordement : Raccordez au téléviseur via
la prise HDMI OUT B.
Menu de réglage : Sélectionnez [Setup] - [HDMI Setup] - [HDMI
Out B Mode] - [Zone2] dans le menu d’accueil. Sélectionnez [Setup]
- [HDMI Setup] - [Zone2 Audio Out] - [Zone2 TV + AMP] depuis le
menu d’accueil.
Bornes SPEAKERSFRONT ACENTERSURROUND
Enceintes 5 canaux et 1 ou 2 caisson de graves
Raccordement : Raccordez les enceintes et le ou les caissons de
graves.
Menu de réglage : Exécutez le calibrage automatique et effectuez
les réglages suivants. Sélectionnez [Setup] - [Speaker Setup] - [SB
Speaker Assign] - [Zone2] dans le menu d’accueil.
Conseil•Sélectionnez [Setup] - [Input Setup] - [In-Ceiling
Speaker Mode] - [On] si vous
utilisez des enceintes au plafond.
Bornes SPEAKERSSURROUND BACK (FRONT B/BI-AMP/ZONE 2) (en cas
d’assignation à la zone 2)
Enceintes 2 canaux Raccordement : Raccordez des enceintes G/D de
la zone 2.
Menu de réglage : Exécutez le calibrage automatique et effectuez
les réglages suivants. Sélectionnez [Setup] - [Speaker Setup] - [SB
Speaker Assign] - [Zone2] dans le menu d’accueil.
-
13FR
Racco
rde
me
nts
Modèles d’enceintes et bornes à raccorderLorsque vous raccordez
des enceintes à l’ampli-tuner, consultez le tableau suivant.Vous
pouvez utiliser ce tableau pour confirmer les modèles d’enceintes
pris en charge par l’ampli-tuner, ainsi que les bornes d’enceintes
auxquelles les enceintes de chaque modèle doivent être
raccordées.Pour régler le modèle d’enceinte, sélectionnez [Setup] -
[Speaker Setup] - [Speaker Pattern] dans le menu d’accueil.
Les abréviations et le symbole utilisés dans la liste sont les
suivants.
FH : Enceintes avant hautesTF : Enceintes avant
supérieuresTM : Enceintes centrales
supérieuresTR : Enceintes arrière
supérieuresRH : Enceintes arrière
hautes
FD : Enceintes avant dotées de la fonctionnalité Dolby
Atmos
SRD : Enceintes surround dotées de la fonctionnalité Dolby
Atmos
SBD : Enceintes surround arrière dotées de la
fonctionnalité Dolby Atmos
: Aucune borne d’enceinte ne peut être affectée et la
sortie est activée à partir des prises PRE OUT uniquement.
SB : Bornes SPEAKERS SURROUND BACK (FRONT B/BI-AMP/ZONE
2)
H1 : Bornes SPEAKERS HEIGHT 1 (ZONE 2)
Ce qu’indiquent les chiffres des modèles d’enceintes :
7 . 1 . 4Nombre d’enceintes situées au niveau de l’auditeur
Nombre de
caissons de graves
Nombre d’enceintes de hauteur ou aériennes (supérieures)
Modèle d’enceinte
Bornes SPEAKERS / prises PRE OUT
Raccordement Zone 2*1
Raccordement d’enceinte Front B*1
Raccordement bi-
amplificateur*1FRONT
A CENTER SURROUND
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (simple)
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
2.0 - - - - - - - SB ou H1 SB SB2.0.2 (TM) - - - - (TM) - - SB
SB SB2.0.2 (FD) - - - - (FD) - - SB SB SB2.1 - - - - - - SB ou H1
SB SB2.1.2 (TM) - - - - (TM) - SB SB SB2.1.2 (FD) - - - - (FD) - SB
SB SB3.0 - - - - - - SB ou H1 SB SB3.0.2 (TM) - - - (TM) - - SB SB
SB3.0.2 (FD) - - - (FD) - - SB SB SB3.1 - - - - - SB ou H1 SB
SB3.1.2 (TM) - - - (TM) - SB SB SB3.1.2 (FD) - - - (FD) - SB SB
SB4.0 - - - - - - SB ou H1 SB SB4.0.2 (FH) - - - (FH) - - SB SB
SB4.0.2 (TM) - - - (TM) - - SB SB SB4.0.2 (FD) - - - (FD) - - SB SB
SB4.0.2 (SRD) - - - (SRD) - - SB SB SB4.0.4 (FH+TM) - - - (FH)
(TM)*2 - SB SB SB4.0.4 (FH+TR) - - - (FH) (TR)*2 - SB SB SB4.0.4
(FH+RH) - - - (FH) (RH)*2 - SB SB SB4.0.4 (TF+TM) - - - (TF) (TM)*2
- SB SB SB4.0.4 (TF+TR) - - - (TF) (TR)*2 - SB SB SB4.0.4 (TF+RH) -
- - (TF) (RH)*2 - SB SB SB4.0.4 (TM+TR) - - - (TM) (TR)*2 - SB SB
SB4.0.4 (TM+RH) - - - (TM) (RH)*2 - SB SB SB4.0.4 (FD+SRD) - - -
(FD) (SRD)*2 - SB SB SB4.1 - - - - - SB ou H1 SB SB
-
14FR
Modèle d’enceinte
Bornes SPEAKERS / prises PRE OUT
Raccordement Zone 2*1
Raccordement d’enceinte Front B*1
Raccordement bi-
amplificateur*1FRONT
A CENTER SURROUND
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (simple)
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
4.1.2 (FH) - - - (FH) - SB SB SB4.1.2 (TM) - - - (TM) - SB SB
SB4.1.2 (FD) - - - (FD) - SB SB SB4.1.2 (SRD) - - - (SRD) - SB SB
SB4.1.4 (FH+TM) - - - (FH) (TM)*2 SB SB SB4.1.4 (FH+TR) - - - (FH)
(TR)*2 SB SB SB4.1.4 (FH+RH) - - - (FH) (RH)*2 SB SB SB4.1.4
(TF+TM) - - - (TF) (TM)*2 SB SB SB4.1.4 (TF+TR) - - - (TF) (TR)*2
SB SB SB4.1.4 (TF+RH) - - - (TF) (RH)*2 SB SB SB4.1.4 (TM+TR) - - -
(TM) (TR)*2 SB SB SB4.1.4 (TM+RH) - - - (TM) (RH)*2 SB SB SB4.1.4
(FD+SRD) - - - (FD) (SRD)*2 SB SB SB5.0 - - - - - SB ou H1 SB
SB5.0.2 (FH) - - (FH) - - SB SB SB5.0.2 (TM) - - (TM) - - SB SB
SB5.0.2 (FD) - - (FD) - - SB SB SB5.0.2 (SRD) - - (SRD) - - SB SB
SB5.0.4 (FH+TM) - - (FH) (TM)*2 - SB SB SB5.0.4 (FH+TR) - - (FH)
(TR)*2 - SB SB SB5.0.4 (FH+RH) - - (FH) (RH)*2 - SB SB SB5.0.4
(TF+TM) - - (TF) (TM)*2 - SB SB SB5.0.4 (TF+TR) - - (TF) (TR)*2 -
SB SB SB5.0.4 (TF+RH) - - (TF) (RH)*2 - SB SB SB5.0.4 (TM+TR) - -
(TM) (TR)*2 - SB SB SB5.0.4 (TM+RH) - - (TM) (RH)*2 - SB SB SB5.0.4
(FD+SRD) - - (FD) (SRD)*2 - SB SB SB5.1 - - - - SB ou H1 SB SB5.1.2
(FH) - - (FH) - SB SB SB5.1.2 (TM) - - (TM) - SB SB SB5.1.2 (FD) -
- (FD) - SB SB SB5.1.2 (SRD) - - (SRD) - SB SB SB5.1.4 (FH+TM) - -
(FH) (TM)*2 SB SB SB5.1.4 (FH+TR) - - (FH) (TR)*2 SB SB SB5.1.4
(FH+RH) - - (FH) (RH)*2 SB SB SB5.1.4 (TF+TM) - - (TF) (TM)*2 SB SB
SB5.1.4 (TF+TR) - - (TF) (TR)*2 SB SB SB5.1.4 (TF+RH) - - (TF)
(RH)*2 SB SB SB5.1.4 (TM+TR) - - (TM) (TR)*2 SB SB SB5.1.4 (TM+RH)
- - (TM) (RH)*2 SB SB SB5.1.4 (FD+SRD) - - (FD) (SRD)*2 SB SB
SB
5.0 (SB) - - - - - H1Non
disponibleNon
disponible
5.0.2 (SB+FH) - - (FH) - -Seulement PRE OUT
Non disponible
Non disponible
5.0.2 (SB+TM) - - (TM) - -Seulement PRE OUT
Non disponible
Non disponible
5.0.2 (SB+FD) - - (FD) - -Seulement PRE OUT
Non disponible
Non disponible
5.0.2 (SB+SRD) - - (SRD) - -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+FH+TM) - - (FH) (TM) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+FH+TR) - - (FH) (TR) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+FH+RH) - - (FH) (RH) -Seulement PRE OUT
Non disponible
Non disponible
-
15FR
Racco
rde
me
nts
Modèle d’enceinte
Bornes SPEAKERS / prises PRE OUT
Raccordement Zone 2*1
Raccordement d’enceinte Front B*1
Raccordement bi-
amplificateur*1FRONT
A CENTER SURROUND
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (simple)
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
5.0.4 (SB+TF+TM) - - (TF) (TM) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+TF+TR) - - (TF) (TR) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+TF+RH) - - (TF) (RH) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+TM+TR) - - (TM) (TR) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+TM+RH) - - (TM) (RH) -Seulement PRE OUT
Non disponible
Non disponible
5.0.4 (SB+FD+SRD) - - (FD) (SRD) -Seulement PRE OUT
Non disponible
Non disponible
5.1 (SB) - - - - H1Non
disponibleNon
disponible
5.1.2 (SB+FH) - - (FH) - Seulement PRE OUT
Non disponible
Non disponible
5.1.2 (SB+TM) - - (TM) - Seulement PRE OUT
Non disponible
Non disponible
5.1.2 (SB+FD) - - (FD) - Seulement PRE OUT
Non disponible
Non disponible
5.1.2 (SB+SRD) - - (SRD) - Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+FH+TM) - - (FH) (TM) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+FH+TR) - - (FH) (TR) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+FH+RH) - - (FH) (RH) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+TF+TM) - - (TF) (TM) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+TF+TR) - - (TF) (TR) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+TF+RH) - - (TF) (RH) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+TM+TR) - - (TM) (TR) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+TM+RH) - - (TM) (RH) Seulement PRE OUT
Non disponible
Non disponible
5.1.4 (SB+FD+SRD) - - (FD) (SRD) Seulement PRE OUT
Non disponible
Non disponible
6.0 (SB) - - - - H1Non
disponibleNon
disponible
6.0.2 (SB+FH) - (FH) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (SB+TM) - (TM) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (SB+FD) - (FD) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (SB+SRD) - (SRD) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+FH+TM) - (FH) (TM) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+FH+TR) - (FH) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+FH+RH) - (FH) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+TF+TM) - (TF) (TM) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+TF+TR) - (TF) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+TF+RH) - (TF) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+TM+TR) - (TM) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+TM+RH) - (TM) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (SB+FD+SRD) - (FD) (SRD) -Seulement PRE OUT
Non disponible
Non disponible
-
16FR
Modèle d’enceinte
Bornes SPEAKERS / prises PRE OUT
Raccordement Zone 2*1
Raccordement d’enceinte Front B*1
Raccordement bi-
amplificateur*1FRONT
A CENTER SURROUND
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (simple)
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
6.1 (SB) - - - H1Non
disponibleNon
disponible
6.1.2 (SB+FH) - (FH) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (SB+TM) - (TM) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (SB+FD) - (FD) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (SB+SRD) - (SRD) - Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+FH+TM) - (FH) (TM) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+FH+TR) - (FH) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+FH+RH) - (FH) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+TF+TM) - (TF) (TM) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+TF+TR) - (TF) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+TF+RH) - (TF) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+TM+TR) - (TM) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+TM+RH) - (TM) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (SB+FD+SRD) - (FD) (SRD) Seulement PRE OUT
Non disponible
Non disponible
6.0 - - - - - H1Non
disponibleNon
disponible
6.0.2 (FH) - - (FH) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (TM) - - (TM) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (FD) - - (FD) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (SRD) - - (SRD) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.2 (SBD) - - (SBD) - -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (FH+TM) - - (FH) (TM) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (FH+TR) - - (FH) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (FH+RH) - - (FH) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (TF+TM) - - (TF) (TM) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (TF+TR) - - (TF) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (TF+RH) - - (TF) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (TM+TR) - - (TM) (TR) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (TM+RH) - - (TM) (RH) -Seulement PRE OUT
Non disponible
Non disponible
6.0.4 (FD+SBD) - - (FD) (SBD) -Seulement PRE OUT
Non disponible
Non disponible
6.1 - - - - H1Non
disponibleNon
disponible
6.1.2 (FH) - - (FH) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (TM) - - (TM) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (FD) - - (FD) - Seulement PRE OUT
Non disponible
Non disponible
6.1.2 (SRD) - - (SRD) - Seulement PRE OUT
Non disponible
Non disponible
-
17FR
Racco
rde
me
nts
Modèle d’enceinte
Bornes SPEAKERS / prises PRE OUT
Raccordement Zone 2*1
Raccordement d’enceinte Front B*1
Raccordement bi-
amplificateur*1FRONT
A CENTER SURROUND
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (simple)
SURROUND BACK (FRONT
B/BI-AMP/ZONE 2) (L/R)
HEIGHT 1 (ZONE 2) HEIGHT 2 SUBWOOFER
6.1.2 (SBD) - - (SBD) - Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (FH+TM) - - (FH) (TM) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (FH+TR) - - (FH) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (FH+RH) - - (FH) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (TF+TM) - - (TF) (TM) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (TF+TR) - - (TF) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (TF+RH) - - (TF) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (TM+TR) - - (TM) (TR) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (TM+RH) - - (TM) (RH) Seulement PRE OUT
Non disponible
Non disponible
6.1.4 (FD+SBD) - - (FD) (SBD) Seulement PRE OUT
Non disponible
Non disponible
7.0 - - - - H1Non
disponibleNon
disponible
7.0.2 (FH) - (FH) - -Seulement PRE OUT
Non disponible
Non disponible
7.0.2 (TM) - (TM) - -Seulement PRE OUT
Non disponible
Non disponible
7.0.2 (FD) - (FD) - -Seulement PRE OUT
Non disponible
Non disponible
7.0.2 (SRD) - (SRD) - -Seulement PRE OUT
Non disponible
Non disponible
7.0.2 (SBD) - (SBD) - -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (FH+TM) - (FH) (TM) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (FH+TR) - (FH) (TR) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (FH+RH) - (FH) (RH) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (TF+TM) - (TF) (TM) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (TF+TR) - (TF) (TR) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (TF+RH) - (TF) (RH) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (TM+TR) - (TM) (TR) -Seulement PRE OUT
Non disponible
Non disponible
7.0.4 (TM+RH