MSG9000 Local EMS Installation Guide (V2009-01) ZTE CORPORATION All Rights reserved, No Spreading abroad without Permission of ZTE i
Sep 08, 2015
ZXABC123V.
MSG9000 Local EMS Installation Guide
(V2009-01)
ZTE CORPORATION
Revision Record
Document No.
Version No.
Drafted by/Modified by
Examined by
Drafted/Modified on
Reasons
Major Modifications (Key Points)
N/A
V2009-01
Wen Haixin
Jiang Haijun
2009-5-27
MSG9000 commissioning SOP
Draft
Contents
11 General Description of SOP
22 Netnumen Server Software Installation
22.1 Overview
22.2 NetNumen Software Installation
72.3 NetNumen Software Configuration
122.4 NetNumen Database Installation
183 NM System Running
183.1 Overview
183.2 Startup of Server Software
193.3 Startup of Client Software
214 Installation of NetNumen Client Software on Remote EMS Server
1 General Description of SOP
Purpose
Install the EMS of MSG9000.
Prerequisites
The local EMS and Server 129 are installed on the same server. The server has been installed with Windows 2003 Server Chinese version + SP2 patch, and SQL Server 2005 Chinese version.
Procedure Description
Perform the installation of local EMS according to Chapter 2 and 3. For the installation of client software on remote EMS server, refer to Chapter 4.
2 Netnumen Server Software Installation
2.1 Overview
This chapter introduces the installation and configuration of NetNumen software and database on the server.
2.2 NetNumen Software Installation
Purpose
Set up the software program part of NetNumen NM server to make it able to manage NEs and serve the NetNumen client.
Prerequisites
Windows 2003 Server Chinese version and SQL Server 2005 Chinese version have been installed.
Tools
MSG9000 version files
Procedure Description
1. Unzip the NetNumenN31-V4 software installation package to the target disk partition. To avoid a long installation directory, please directly unzip it to the first level directory of the partition, for example, to the D:\EMS directory. The installation source directory of unzipped version is shown in the Figure 2.21.
Figure 2.21 Contents of Installation Package
2. Click to run the installation file install.bat, and the Figure 2.22 pops up. Begin the version installation.
Figure 2.22 Language Selection
3. To install the Chinese version, input 2; to install English version, input 1. The language selected here should be consistent with that on Figure 2.31, otherwise the user cannot log on to the client.
Figure 2.23 Installation Directory Setting
4. Input the target installation directory of NetNumenN31. And then press the Enter key.
Figure 2.24 Installation Type Selection
5. Select the Type 2 Client and Server, as shown in the Figure 2.24. And then press the Enter key to unzip the package.
Figure 2.25 Unzip the Package
6. It takes a long time to unzip the package, please wait patiently. After all version files are unzipped, the installation program automatically starts the configuration center of NetNumenN31 software.
Figure 2.26 Configuration Center
Subsequent Procedure:
Software configuration: after all version files are unzipped, the installation program automatically starts the configuration center of NetNumenN31 software.
The configuration center can also be started manually, with the startup path shown in the Figure 2.27.
Figure 2.27 Startup Path of Configuration Center
2.3 NetNumen Software Configuration
Purpose
Configure the NetNumen software to make it connect to SQL database, and ensure the network between NetNumen and NEs/client is normal.
Prerequisites
NetNumen software has been installed successfully.
Procedure Description
1. Check the basic configuration:
View the Basic Information in the NetNumen Config Center window, as shown in the Figure 2.31. Select the language in which the NetNumenN31 system is running. The selected language should be consistent with that in software installation in Figure 2.22. Click the Save button.
The right pane shows the NM software version and OS related information.
Figure 2.31 Configuration Center Basic Information
2. Click NE Module in the NetNumen Config Center window and then select the NE ZXMSG 9000 to be managed by the installed NetNumenN31.
Figure 2.32 Configuration Center NE Module
Click Save. The Set Successfully prompting dialog box appears.
3. Click Database Configuration in the NetNumen Config Center window to set the connection parameters of the NetNumenN31 database.
(1) Select MS SQL Server as the Database Type.
Figure 2.33 Configuration Center Database Configuration
(2) Set the logon password of database system administrator sa. By default, the password is netnumen. If the sa password of currently installed SQL Server database is not the default netnumen, please use the existing password. Modify relevant settings of NetNumenN31 according to current sa password of SQL Server via the Configuration Center, as shown in the figure below. Double click the Value column of Database System Administrator Password to modify the sa password of the current SQL Server. For other parameters shown in the Figure 2.34, keep the default settings. Click the Save button.
Figure 2.34 Database Configuration Modification
4. Click Short Cut in the NetNumen Config Center window to enter the Short Cut window.
Figure 2.35 Configuration Center Short Cut
Click the Save button after the configuration, as shown in the Figure 2.35. Then click the Close button to finish the configuration.
2.4 NetNumen Database Installation
Purpose
Initialize the database and realize the connection with database.
Prerequisites
NetNumen software configuration has been finished.
Procedure Description
1. Check the SQLCMD.exe environment variables: open the windows command line window and execute the command sqlcmd. Observe the execution result.
If the result is as shown in the Figure 2.41, it indicates the environment variables have been loaded and you can start the installation of database.
Figure 2.41 Check Environment Variables Loaded
If the result is as shown in the Figure 2.42, it indicates the environment variables are not loaded and you need to perform the following steps.
Figure 2.42 Check Environment Variables Unloaded
Search the SQLCMD.exe file under the SQL Server 2005 installation directory and add its directory to the system environment variable.
Figure 2.43 Add Environment Variable
2. Start the NetNumen N31 Init Database shortcut, with the path shown in the Figure 2.44.
Figure 2.44 Start Path of Database Installation Program
Click Initialize Database and the window pops up, as shown in the Figure 2.45.
Figure 2.45 Database Installation Window
3. Input Y and press the Enter key to begin the initialization of database.
The system prompts Build successful. At this time you can complete the initialization of database by putting any key.
Figure 2.46 Database Installation Completed
4. Start the NetNumenN31 Config Center and enter the Database Configuration window, as shown in the Figure 2.47.
Figure 2.47 Test Database Connection
The test result Connecting database is complete successfully indicates the previous database initialization is successful. The installation of server is finished.
3 NM System Running
3.1 Overview
Firstly start the server software and then client software.
3.2 Startup of Server Software
Purpose
Start the NM server software and verify the correctness of installation.
Prerequisites
The client and server have been installed successfully.
Procedure Description
1. There are two shortcuts NetNumen N31 Server and NetNumen N31 Client on the Windows desktop.
Figure 3.21 Desktop Icon of NM Server
2. Double click the shortcut of NetNumen N31 Server to start the NetNumen unified management system console. In the case of default configuration, the console automatically starts the NetNumen network management process, CORBA notification service process, and FTP process (NetNumen assistant process). After the service processes are started, a green icon appears on the window.
Figure 3.22 Management System Console Startup Completed
3.3 Startup of Client Software
Purpose
Run the client and manage NEs.
Prerequisites
The installation of NM server software has been completed.
Procedure Description
1. Double click the shortcut of NetNumen N31 client on the desktop and a window pops up, as shown in the Figure 3.3-1.
Figure 3.31 Logon Window of Client
2. Click the OK button, and the startup is completed. As shown in the Figure 3.32.
Figure 3.32 Management Window of NetNumen
4 Installation of NetNumen Client Software on Remote EMS Server
Purpose
Install the NetNumen client on remote EMS server.
Prerequisites
NetNumen server has been installed. The computer on which the client is to be installed has been installed with Windows XP system. The client and local server are in the same network segment or the client can access the local server.
Procedure Description
1. Compress the server installation files ums-clnt, jdk-windows and upgradeN31 into a package as the client program. The file structure is as shown in the figure below.
Figure 3.31 NM Directory Structure
2. Copy the client program to other computers and then delete the ums-clnt\temp directory.
1-1
1-2
iii
All Rights reserved, No Spreading abroad without Permission of ZTE