-
(1) AllgemeinesDieses Netzgerät besitzt viele Besonderheiten,
die bei Industrienetzgeräten zuvor nichtgegeben waren. Es ist so
konstruiert, dass es die üblichen Störfestigkeit im
Industriebereichausgleicht. Zudem ermöglichen die niedrigen
Emissionswerte, den Einsatz im Wohn-,Geschäfts- und
Leicht-Industrie-Bereich.Durch die aktive Leistungsfaktor-Korrektur
(PFC) ist das Gerät auch für den Betrieb vonBeleuchtungen sehr gut
geeignet.Das Netzgerät hat die positive Eigenschaft, größere
Anlauf- und Kurzschlussströme zuliefern, so dass auch bestimmte
Sicherungsautomaten auslösen.Steckverbinder nur im spannungsfreien
Zustand verdrahten!Diese kompakte Stromversorgung ist vergossen und
somit für raue Umgebungsbedingungengeeignet.
(3) Ausrüstung[1] Ausgang:5-polige 7/8" Buchse mit
Innengewinde.Ziehen Sie den Gegenstecker mit dem „Murrelektronik
7/8’’ Montageschlüssel-Set AF 22,Drehmoment 1,5 Nm an. Art.
Nr.:7000-99104-0000000 mit passendem 7/8’’ Montageschlüssel.
[2] Eingang:3-poliger 7/8" Stecker mit Außengewinde.Ziehen Sie
den Gegenstecker mit dem „Murrelektronik 7/8’’ Montageschlüssel-Set
AF 22,Drehmoment 1,5 Nm an. Art. Nr.:7000-99104-0000000 mit
passendem 7/8’’ Montageschlüssel.
[3] Zweifarbige LED, Ausgangsspannung “OK” - grün, Alarm /
Fehler - rot.- LED leuchtet rot auf, bei Kurzschluss, Überlast oder
erhöhter.[5] Hoher Wirkungsgrad bei Teillast / minimale Verluste
bei Leerlauf.[6] Temperatur / Leistung Diagramm.(4) EinbauartDas
Netzteil wird durch natürliche Konvektion gekühlt. Die Schutzart
des Gehäuses ist IP67.Schaltnetzteil für die Verwendung im
Schaltschrank und außerhalb des Schaltschranks mit7/8 ‘’ Eingangs
und 7/8 ‘’ Ausgangsanschlüssen.(5) Montage [4]- Frontmontage: 6 x
M4 Schrauben.- Seitliche Montage: 4 x M4 Schrauben.Vertikale und
horizontale Montage möglich. Nicht für direkte
Sonneneinstrahlung.(6) EinschaltenÜberprüfen Sie die Verdrahtung
der Ein- und Ausgänge vor dem Einschalten.(7) NutzlastDer Nennstrom
von 4 A wurde aufgrund der industriellen Belastungen so ausgelegt,
dassLasten mit hohen Einschaltströmen unterstützt werden, ohne die
Stromversorgung zubeschädigen oder abzuschalten. Kennlinie [7]
zeigt das typische Spannung / Strom Verhältnis.Der Abfallende Teil
der Kurve [7] zeigt die Strombegrenzung. Das Netzgerät ist
ausgelegteine Ausgangsleistung von 150% (Power Boost), für eine
Dauer von mindestens 5 Sekundenzu liefern [8].(8) Reihenbetrieb
[9]Max.2 Geräte in Serie um den SELV Ausgang beizubehalten. Bei
mehr als zwei Geräten inSerie übersteigt die Ausgangsspannung die
zulässige Spannungsgrenze für SELV.(9) Ausgangskurzschluß-SchutzDas
Netzgerät kann bei Kurzschluß z.B. folgende ABB Sicherungsautomaten
auslösen:
S201-Z1,6A(10) NormenElektrosicherheit IEC / EN 60950-1, SELVEMV
EN 61204-3 EMI: Klasse B, EMS: IndustriebereichVerträglichkeit EN
61000-4-2 ESD 4/8 kV
EN 61000-4-3 Rf-field 10 V/mEN 61000-4-4 EFT/B 2/2 kVEN
61000-4-5 Surge 1/2 kVEN 61000-4-6 Cond. Rf 10 VEN 61000-4-11
Störaussendungen EN 55022 B, FunkstörungenEN 61000-3-2 Klasse
AEN 61000-3-3EN 60204-1 60 V / 1 sEN 50178 OVC III bis zu 4000 m
mit Derating
(Derating über 2000 m / Ausgangsleistung 6,25% / 1000 m oder
Umgebungstemperatur 5°C / 1000 m)Änderungen vorbehalten.
Product of the Emparro67 series
Lesen Sie diese Bedienungsanleitung vorEinbau und Gebrauch des
Netzgerätesaufmerksam durch, damit Sie die
besonderenGebrauchseigenschaften des Netzgerätesnutzen können. Das
Netzgerät enthältEigenschaften, die Ihnen zu mehrZuverlässigkeit in
Ihrem System verhelfen.Bewahren Sie diese Anleitung für
einenmöglichen späteren Gebrauch auf.
Emparro67 4-100-240/24 7/8"-7/8"
Art. Nr. 9000-11112-1962020
BEDIENUNGSANLEITUNG
(2) Technische Spezifikationen, Art. Nr. 9000-11112-1962020 Rev.
1.3Nennspannung 100 - 240 VAC, 100 - 240
VDCEingangsspannungsbereich 90 - 265 VAC, 90 - 370
VDCNetzwerkarchitektur TN, TT, ITNennfrequenz 50 - 60 Hz
±6%Eingangsstrom, I���� 1,1 A / 100 - 0,5 A / 240 VAC /
VDCEinschaltstromstoß / I²t < 6 A / 230 VAC nach 1 ms / 0,16
A²sWirkungsgrad, typ. 91,7% / 115 VAC - 92,4% / 230
VACLeistungsfaktor typ. 0,98 / 230 VACAusgangsleistung 96
WVerlustleistung < 7,9 W bei 230 VACVerlustleistung (ohne Last)
< 1 W bei 230 VACInterne Sicherung 6,3 A (T)
Vorsicherung maximal 20 A (T) in der
Gebäudeinstallation.Leitungsshutzschalter Typ B oder C
empfohlen.
Schutzklasse 1Ausgangsspannung, fest 24,1 VDCRegelung
+/-2%Regelung, dynamisch, typ. 0 -> 100%, 5% 2 ms / 100% ->
5%, 5% 2 msAnlaufzeit, typ. < 500 msNetzausfallüberbrückungszeit
> 45 ms / 230 VACAusgangsstrom 24 VDC 4 A (+60°C) / 2,4 A
(+70°C)Ausgangsstrom (Power boost) 6 A / > 5 sKurzschluß, typ.
4,4 ARestwelligkeit < 20 mV ���Überlastschutz /
Überhitzungsschutz jaÜberspannungsauslöser jaRelative Feuchtigkeit
4 - 100%Betriebstemperatur -40°C - +85°C (> +60°C derating)*Zur
Bedienung zugelassener Bereich -40°C - +40°CLagertemperatur -40°C -
+85°CGehäuseschutzklasse, Gehäuse, EN 60529 IP67Abmessungen B x H x
T; Gewicht 111 x 141 x 54 mm; 1,1 kg
* UL Zulassung, max. Umgebungstemperatur der Luft -40°C -
+80°C.
8
5
7
1 2 3 4 5 61 2 3 4 5 6
(A)
(V)
50% 100% 150%50% 100% 150%
(V)
(A)
dauernd 5 sec.
88 ,0 0%
88 ,5 0%
89 ,0 0%
89 ,5 0%
90 ,0 0%
90 ,5 0%
91 ,0 0%
91 ,5 0%
92 ,0 0%
92 ,5 0%
93 ,0 0%
50 % 75 % 10 0%
11 5VAC
23 0VAC
Ausgangslast [%]
Wir
ku
ng
sg
rad
[%]
N
L
N
L
9
IP67
IND.CONT. EQ.IND.CONT. EQ.61RM61RM
1 23
133
mm
141
mm
111 mm
109 mm
45 mm 45 mm45 mm10 mm10 mm
54 mm
42 mm6 mm
125
mm
5 mm
4
OK /ALARM
OK /ALARM
INPUTINPUTL / DC+L / DC+
N / DC-N / DC-
CAUTIONCAUTION
Read instruction manual before installation and use.Read
instruction manual before installation and use.
MADE IN CZECH REPUBLICMADE IN CZECH REPUBLIC
DESIGNED IN FINLANDDESIGNED IN FINLAND
ART. NO. 9000-11112-1962020ART. NO. 9000-11112-1962020
Emparro67 4-100-240/24Emparro67 4-100-240/24
OUTPUTOUTPUT
__
+
____
+
IND.CONT.EQ.61RM
TcIP67
(DC+/-24V)
(DC48V)
( C)°(°C)
0
(A)
-40 -20 0 20 40 60 80 100-40 -20 0 20 40 60 80 100
1
2
3
4
5
6
6
A
A
__
+
____
+
N / DC-
L / DC+
-
(1) GeneralThis unit employs many features previously
unavailable in an industrial power supply. It hasbeen designed to
withstand the high levels of interference found in heavy industry
and hasemission levels low enough for it to be used in residential,
commercial and light industrialenvironments.This unit can also be
used with lighting due to active power factor correction.The
Emparro67 4-100-240/24 7/8"-7/8" has a high level of reserve power.
This enables loadswith significant inrush current to be supported
and will also ensure that circuit breakers will tripin event of
short circuit.Plug connector only under zero voltage (Insert /
Remove).The compact power supply unit is potted and suitable for
harsh environmental conditions.
(3) Features[1] Output terminal:5-pin 7/8" receptacle female
with internal threads.To tighten the mating connector use
Murrelektronik 7/8" 1.5 Nm torque wrench set AF 22:Art. No.:
7000-99104-0000000 with correct 7/8" wrench.
[2] Input terminal:3-pin 7/8" receptacle male with external
threads.To tighten the mating connector use Murrelektronik 7/8" 1.5
Nm torque wrench set AF 22:Art. No.: 7000-99104-0000000 with
correct 7/8" wrench.
[3] Bi-colour LED, output voltage “OK” - green, Alarm - red.-
led can be red due to over temperature, short circuit or over
load.[5] High efficiency with partial load / minimum losses with
no-load.[6] Temperature derating curve.(4) LocationThe power supply
is cooled by natural convection. Protection degree of the housing
is IP67.Switch-Mode Power Supply for both inside and outside of the
cabinet with 7/8’’ input and 7/8’’output connectors.(5) Mounting
[4]- front mounting with 6 x M4 screws.- side mounting with 4 x M4
screws.Vertical and horizontal mounting is possible. Not for direct
sunlight.(6) Switching onCheck input and output connectors and
their connection before switching power on.(7) Loading capacityThe
nominal current is 4 A but due to the nature of industrial loading,
the power supply has beendesigned to support loads with high inrush
currents without damage or shutdown. Curve [7]shows the typical
voltage / current curve. Decreasing part of the curve [7] shows the
currentlimitation. Power supply is designed to give 150% output
power (power boost) for min. 5 seconds[8].(8) Series connection
[9]Max. 2 units in series to guarantee the SELV output. With more
than 2 units in series, the outputvoltage will exceed the SELV
limits.(9) Using circuit breakers on the power supply output:On the
short circuit, the power supply will trip, for example, the
following ABB circuit breaker:
S201-Z1,6A(10) StandardsElectrical safety IEC / EN 60950-1,
SELVEMC EN 61204-3 EMI: Class B, EMS: Industrial
environmentImmunity EN 61000-4-2 ESD 4/8 kV
EN 61000-4-3 Rf-field 10 V/mEN 61000-4-4 EFT/B 2/2 kVEN
61000-4-5 Surge 1/2 kV; 500 VEN 61000-4-6 Cond. Rf 10 VEN
61000-4-11
Emissions EN 55022 B RF-emissionsEN 61000-3-2 class AEN
61000-3-3EN 60204-1 60 V / 1 sEN 50178 OVC III up to 4000 m with
derating
(derating above 2000 m / output power 6,25% / 1000 m or ambient
temperature 5°C / 1000 m)We reserve the right to change this
specification.
Product of the Emparro67 series
In order to take the best advantage of thefeatures that this
power supply has tooffer and to ensure long term reliabilityfor
your equipment, please read theseinstructions carefully before
installationand use. They should be retained forfuture
reference.
Emparro67 4-100-240/24 7/8"-7/8"
Art. No. 9000-11112-1962020
OPERATING INSTRUCTIONS
(2) Technical specification, Art. No. 9000-11112-1962020 Rev.
1.3Nominal voltage 100 - 240 VAC, 100 - 240 VDCInput voltage range
90 - 265 VAC, 90 - 370 VDCPower distribution systems TN, TT, IT
mainsNominal frequency 50 - 60 Hz ±6%Input current, I���� 1,1 A /
100 - 0,5 A / 240 VAC / VDCInrush current / I²t < 6 A / 230 VAC
after 1 ms / 0,16 A²sEfficiency, typ. 91,7% / 115 VAC - 92,4% / 230
VACPower factor, typ. 0,98 with 230 VACOutput power 96 WPower
losses < 7,9 W with 230 VACNo-load power losses < 1 W with
230 VACInternal fuse 6,3 A (T)
External fuse max. 20 A (T) in building installations.
Circuitbreaker type B or C recommended.Safety class 1Output
voltage, fixed 24,1 VDCStatic regulation accuracy +/-2%Dynamic
regulation accuracy typ. 0->100%, 5% 2ms / 100%->5%, 5%
2msStart-up time < 500 msHold up time of the output > 45 ms /
230 VACOutput current, continuous 24 VDC 4 A (+60°C) / 2,4 A
(+70°C)Output current (power boost) 6 A / > 5 sOutput current,
short circuit, typ. 4,4 AOutput ripple < 20 mV ���Overloading /
overtemperature protection YesOvervoltage supervision YesRelative
humidity 4 - 100%Operation temperature -40°C - +85°C (> +60°C
derating)*Operator access area -40°C - +40°CStorage temperature
-40°C - +85°CProtection degree of the housing, EN 60529
IP67Dimensions W x H x D; Weight 111 x 141 x 54 mm; 1,1 kg
* UL approval max. surrounding air temperature -40°C - +80°C
8
5
7
1 2 3 4 5 61 2 3 4 5 6
(A)
(V)
50% 100% 150%50% 100% 150%
(V)
(A)
continuously 5 sec.
88 ,0 0%
88 ,5 0%
89 ,0 0%
89 ,5 0%
90 ,0 0%
90 ,5 0%
91 ,0 0%
91 ,5 0%
92 ,0 0%
92 ,5 0%
93 ,0 0%
50 % 75 % 10 0%
11 5VAC
23 0VAC
Output load [%]
Eff
icie
ncy
[%]
IP67
IND.CONT. EQ.IND.CONT. EQ.61RM61RM
1 23
133
mm
141
mm
111 mm
109 mm
45 mm 45 mm10 mm
54 mm
42 mm6 mm
125
mm
5 mm
4
OK /ALARM
OK /ALARM
INPUTINPUTL / DC+L / DC+
N / DC-N / DC-
CAUTIONCAUTION
Read instruction manual before installation and use.Read
instruction manual before installation and use.
MADE IN CZECH REPUBLICMADE IN CZECH REPUBLIC
DESIGNED IN FINLANDDESIGNED IN FINLAND
ART. NO. 9000-11112-1962020ART. NO. 9000-11112-1962020
Emparro67 4-100-240/24Emparro67 4-100-240/24
OUTPUTOUTPUT
__
+
____
+
IND.CONT.EQ.61RM
TcIP67
N
L
N
L
9
(DC+/-24V)
(DC48V)
( C)°(°C)
0
(A)
-40 -20 0 20 40 60 80 100-40 -20 0 20 40 60 80 100
1
2
3
4
5
6
6
A
A
__
+
____
+
N / DC-
L / DC+
-
(1) GénéralitésCe produit dispose de nombreuses caractéristiques
jusqu’alors indisponibles dans unealimentation industrielle. Il a
été étudié afin de supporter les fortes contraintes
d’interférencesliées aux industries lourdes et émet à des niveaux
suffisamment bas pourêtre utilisable dans le tertiaire et les
industries légères.Ce produit peut être utilisé dans un
environnement tel que l’éclairage grâce à un circuit actif
decorrection de facteur de puissance.L’alimentation a une réserve
de puissance élevée. Ceci permet d’y connecter des
chargesconsommant de fortes intensités au démarrage et garantissent
un déclenchement desdisjoncteurs en cas de court-circuit.Ne
brancher un connecteur qu’en l’absence de potentiel (à l’insertion
comme au retrait).L’alimentation compacte est résinée et supporte
les environnements sévères.
(3) Caractéristiques[1] Prise en sortie :Prise femelle taraudée
à 5-poles 7/8".Pour un serrage optimale du connecteur 7/8" utiliser
la clef dynamométrique tarée à 1,5 Nm AF22 avec l’option 7/8":
Article n°: 7000-99104-0000000.
[2] Prise en entrée :Prise mâle filetée à 3 poles 7/8".Pour un
serrage optimale du connecteur 7/8" utiliser la clef dynamométrique
tarée à 1,5 Nm AF22 avec l’option 7/8": Article n°:
7000-99104-0000000.
[3] LED bicolore, tension de sortie “OK” - vert, Alarme -
rouge.- la LED est allumée en rouge en cas de surchauffe, de
court-circuit ou de surcharge.[5] Haut rendement à charge réduite /
pertes minimum à vide.[6] Courbe de dégradation avec la
température.(4) EmplacementL’alimentation est refroidie par
convection naturelle. L’indice de protection est IP67.Alimentation
à découpage à utiliser à l’intérieur ou à l’extérieur de l’armoire
avec desconnecteurs d’entrée et de sortie 7/8".(5) Montage [4]-En
face avant avec 6 vis M4.-De côté avec 4 vis M4.Les montage en
vertical ou en horizontal sont possibles. Ne pas exposer au
soleil.(6) A la mise en marcheVérifier les connections d’entrée et
de sortie avant l’allumage.(7) Charges admissiblesLe courant
nominal est de 4 A mais dû à la nature des charges en milieu
industriel, l’alimentationa été développée pour supporter des
charges ayant un fort courant d’appel sans se détériorerou se
couper. La courbe [7] montre la courbe Tension / Courant typique.
La partie descente dela courbe [7] montre le courant de limitation.
L’alimentation est étudiée pour fournir 150% ensortie (“Power
Boost”) pendant 5 secondes au moins [8].(8) Connexion en série
[9].2 produits max en série pour rester dans la gamme de sortie
SELV. La mise en série de plusde 2 produits donnera une sortie
excédant les limites SELV.(9) Protection contre les courts-circuits
à la sortie:Exemple de disjoncteur à utiliser: ABB
S201- Z1,6A(10) NormesSécurité électrique IEC/EN 60950-1,SELVCEM
EN 61204-3 Immunité l’industrielle, Emissions class BImmunité EN
61000-4-2 ESD 4/8 kV
EN 61000-4-3 Rf-field 10 V/mEN 61000-4-4 EFT/B 2/2 kVEN
61000-4-5 Surtension 1/2 kV; 500 VEN 61000-4-6 Cond. Rf 10 VEN
61000-4-11
Emissions EN 55022 B émissions radioEN 61000-3-2 classe AEN
61000-3-3EN 60204-1 60 V / 1 sEN50178 OVC III jusqu’à 4000 m avec
dégradation
des performances.(dégradation au-delà de 2000 m/ puissance
sortie diminuée de 6,25% / 1000 m ou température ambiante 5°C /1000
m)(Nous nous réservons le droit de modifier ces spécifications sans
préavis)
Product of the Emparro67 series
Pour vous permettre de profiter aumaximum des caractéristiques
de cettealimentation, nous vous conseillons delire attentivement
ces instructions avantson montage et sa mise en service.Conservez
ces documents pour uneconsultation future.
Emparro67 4-100-240/24 7/8"-7/8"
Ref.: 9000-11112-1962020
Instructions de service
(2) Caractéristiques techniques, Ref. 9000-11112-1962020 Rev.
1.3Tension nominale 100 - 240 VAC, 100 - 240 VDCPlage de tension
d’entrée 90 - 265 VAC, 90 - 370 VDCRégime de neutre TN, TT,
ITFréquence nominale 50 - 60 Hz ±6%Courant nominal, Inom 1,1 A /
100 VAC - 0,5 A / 240 VAC / VDCCourant d’appel / I²t < 6 A / 230
VAC ensuite 1 ms / 0,16 A²sRendement, typ 91,7% / 115 VAC - 92,4% /
230 VACFacteur de puissance, typ 0,98 / 230 VACPuissance de sortie
96 WPertes < 7,9 W / 230 VACPertes à vide < 1 W / 230
VACFusible interne 6,3 A (T)
Fusible externe, max. 20 A (T) dans le bâtiment. Disjoncteur
typeB ou C recommandé.Classe de protection 1Tension de sortie 24,1
VDCRégulation tension de sortie +/-2%Régulation dynamique
0->100%, 5% 2ms / 100%->5%, 5% 2msTemps de départ < 500
msTemps de maintient > 45 ms / 230 VACCourant 24 VDC 4 A (+60°C)
/ 2,4 A (+70°C)Courant “Power boost” 6 A / > 5 sCourant de court
circuit, typ. 4,4 AOndulation résiduelle < 20 mV ���Dispositif
de protection surcharge/surchauffe OuiProtection des surtensions
OuiHumidité relative 4 - 100%Temperature ambiante maximale -40°C -
+85°C (> +60°C derating)*Zone d’accès à l’opérateur -40°C -
+40°CTempérature de stockage -40°C - +85°CIndice de protection du
boîtier, EN 60529 IP67Dimensions L x H x P; Poids 111 x 141 x 54
mm; 1,1 kg
* Certification UL pour une gamme de température ambiante de
–40°C à +80°C.
8
5
7
1 2 3 4 5 61 2 3 4 5 6
(A)
(V)
50% 100% 150%50% 100% 150%
(V)
(A)
continue 5 sec.
88 ,0 0%
88 ,5 0%
89 ,0 0%
89 ,5 0%
90 ,0 0%
90 ,5 0%
91 ,0 0%
91 ,5 0%
92 ,0 0%
92 ,5 0%
93 ,0 0%
50 % 75 % 10 0%
11 5VAC
23 0VAC
Charge de sortie [%]
Ren
dem
en
t[%
]
IP67
IND.CONT. EQ.IND.CONT. EQ.61RM61RM
1 23
133
mm
141
mm
111 mm
109 mm
45 mm 45 mm10 mm
54 mm
42 mm6 mm
125
mm
5 mm
4
OK /ALARM
OK /ALARM
INPUTINPUTL / DC+L / DC+
N / DC-N / DC-
CAUTIONCAUTION
Read instruction manual before installation and use.Read
instruction manual before installation and use.
MADE IN CZECH REPUBLICMADE IN CZECH REPUBLIC
DESIGNED IN FINLANDDESIGNED IN FINLAND
ART. NO. 9000-11112-1962020ART. NO. 9000-11112-1962020
Emparro67 4-100-240/24Emparro67 4-100-240/24
OUTPUTOUTPUT
__
+
____
+
IND.CONT.EQ.61RM
TcIP67
N
L
N
L
9
(DC+/-24V)
(DC48V)
( C)°(°C)
0
(A)
-40 -20 0 20 40 60 80 100-40 -20 0 20 40 60 80 100
1
2
3
4
5
6
6
A
A
__
+
____
+
N / DC-
L / DC+
-
(1) GeneralEsta unidad presenta numerosas características no
disponibles hasta el momento en unafuente de alimentación
industrial. Ha sido diseñada para soportar los niveles más altos
quepuedan darse en la industria pesada y sus niveles de emisión son
lo suficientemente bajos parapoder ser utilizadas en ambientes
residenciales, comerciales y de industria ligera.Esta unidad puede
utilizarse con iluminación gracias a su factor activo de corrección
depotencia.La fuente tiene un alto nivel de potencia de reserva, lo
que permite soportar cargas concorrientes de entrada elevadas, y
también asegura que los fusibles se activarán en caso
decortocircuito.Conector enchufable solo en caso de voltaje cero
(Introducir/Sacar).Esta fuente de alimentación compacta está
totalmente sellada y está indicada para condicionesambientales
extremas.
(3) Características[1] Terminal de salida:Conector hembra 5 pins
7/8" con hilo interno.Para tensar el conector acoplado, utilice la
llave dinamométrica 7/8" 1.5 Nm set AF22 deMurrelektronik:
Referencia 7000-99104-0000000 con la correcta llave.
[2] Terminal de entradaConector macho 3 pines 7/8"con hilos
externosPara tensar el conector acoplado, utilice la llave
dinamométrica 7/8" 1.5 Nm set AF22 deMurrelektronik: Referencia
7000-99104-0000000 con la correcta llave.
[3] LED bicolor, voltaje de salida “OK” - verde, Alarma - rojo.-
el LED puede ser rojo a causa de un sobrecalentamiento,
cortocircuito o sobrecarga[4] Alta eficiencia con carga parcial /
pérdidas mínimas sin carga.[5] Curva de derating de temperatura.(4)
EmplazamientoLa fuente de alimentación se refrigera por convección
natural. El grado de protección de laarcasa es IP67. La fuente de
alimentación cuenta con modo switch tanto en el interior como enel
exterior del armario de control con conectores de entrada y salida
de 7/8".(5) Montaje- montaje frontal con 6 tornillos M4- montaje
lateral con 4 tornillos M4También es posible el montaje vertical y
horizontal. No apto para luz del sol.(6) EncendidoCompruebe los
conectores de entrada y salida y su conexión antes de poner en
marcha elaparato.(7) Capacidad de cargaLa corriente nominal es 4 A
pero a causa de la naturaleza de la carga industrial, la fuente
dealimentación ha sido diseñada para soportar cargas con altas
corrientes de entrada sin sufrirdaños o paros. La curva [6] muestra
el voltaje típico/curva de corriente. La parte descendientede la
curva [6] muestra la limitación de corriente. La fuente de
alimentación está diseñada paraproporcionar el 150% de la potencia
de salida (power boost) durante un mínimo de 5 segundos[7].(8)
Conexión serie [8].Máximo 2 unidades en serie para garantizar la
salida SELV. Con más de 2 unidades en serie,el voltaje de salida
excedería los límites SELV.(9) Activación de circuitos protectores
a la salida de la fuente:En el caso de un cortocircuito, la fuente
puede activar, por ejemplo, el protector térmico ABBsiguiente:
S201-Z1,6A(10) NormativasSeguridad eléctrica IEC / EN 60950-1,
SELVEMC EN 61204-3 Immunidad industrial, Emisiones BInmunidad EN
61000-4-2 ESD 4/8 kV
EN 61000-4-3 Rf-field 10 V/mEN 61000-4-4 EFT/B 2/2 kVEN
61000-4-5 Surge 1/2 kV; 500 VEN 61000-4-6 Cond. Rf 10 VEN
61000-4-11
Emisiones EN 55022 B emisiones RFEN 61000-3-2 clase AEN
61000-3-3EN 60204-1 60 V / 1 sEN 50178 OVC III bis zu 4000 m mit
Derating
(derating sobre 2000m / tensión de salida 6,25%/ 1000 m o
temperatura ambiente 5ºC/ 1000m)(Reservado el derecho de
modificaciones)
Product of the Emparro67 series
Para aprovechar al máximo las característicasde esta fuente de
alimentación y para aseguraruna larga fiabilidad a sus equipos,
leaconsejamos lea estas instrucciones conatención antes de la
instalación y su posterioruso. Estas habrían de servir como
referenciapara futuras consultas.
Emparro67 4-100-240/24 7/8"-7/8"
Ref.: 9000-11112-1962020
Instrucciones de montaje y uso
(2) Especificaciones técnicas, Ref. 9000-11112-1962020 Rev.
1.3Tensión de nominal 100 - 240 VAC, 100 - 240 VDCRango de tensión
de entrada 90 - 265 VAC, 90 - 370 VDCSistemas de distribución de
potencia Redes TN,TT, ITFrecuencia nominal 50 - 60 Hz ±6%Corriente
de entrada, Inom 1,1 A / 100 VAC - 0,5 A / 240 VAC / VDCCorriente
de arranque / I²t < 6 A / 230 VAC después 1 ms / 0,16
A²sEficiencia (típica) 91,7% / 115 VAC - 92,4% / 230 VACFactor de
potencia (típico) 0,98 / 230 VACSalida de potencia 96 WPérdidas de
energía < 7,9 W / 230 VACPérdidas de energía sin carga < 1 W
- 230 VACFusible interno 6,3 A (T)
Fusible externo, máx. 20 A (T) en instalaciones de edificios se
recomienda eluso de protecciones magnetotérmicas tipo B o C
Tipo de protección 1Voltaje de salida 24,1 VDCRegulación en
estática +/-2%Regulación dinámica 0->100%, 5% 2ms / 100%->5%,
5% 2msTiempo de arranque,tip. < 500 msTiempo de retención de la
salida (caída de red) > 45 ms / 230 VACCorriente de salida 24
VDC 4 A (+60°C) / 2,4 A (+70°C)Corriente de salida (power boost) 6
A / > 5 sCorriente de salida, en cortocircuito, tip. 4,4 ARizado
de salida < 20 mV ���Sobrecarga / Protección de temperatura
SíDesconexión por sobrevoltaje SiHumedad relativa 4 -
100%Temperatura máxima del aire -40°C - +85°C (> +60°C
derating)Area de acceso del operador -40°C - +40°CTemperatura de
almachen -40°C - +85°CGrado de protección de la caracasa, EN 60529
IP67Dimensiones W x H x D; Peso 111 x 141 x 54 mm; 1,1 kg
* Normativa UL temperatura máxima del aire -40ºC - +80ºC.
8
5
7
1 2 3 4 5 61 2 3 4 5 6
(A)
(V)
50% 100% 150%50% 100% 150%
(V)
(A)
continuo 5 sec.
88 ,0 0%
88 ,5 0%
89 ,0 0%
89 ,5 0%
90 ,0 0%
90 ,5 0%
91 ,0 0%
91 ,5 0%
92 ,0 0%
92 ,5 0%
93 ,0 0%
50 % 75 % 10 0%
11 5VAC
23 0VAC
Carga de salida [%]
Efi
cie
nc
ia[%
]
IP67
IND.CONT. EQ.IND.CONT. EQ.61RM61RM
1 23
13
3m
m
14
1m
m
111 mm
109 mm
45 mm 45 mm10 mm
54 mm
42 mm6 mm
12
5m
m
5 mm
4
OK /ALARM
OK /ALARM
INPUTINPUTL / DC+L / DC+
N / DC-N / DC-
CAUTIONCAUTION
Read instruction manual before installation and use.Read
instruction manual before installation and use.
MADE IN CZECH REPUBLICMADE IN CZECH REPUBLIC
DESIGNED IN FINLANDDESIGNED IN FINLAND
ART. NO. 9000-11112-1962020ART. NO. 9000-11112-1962020
Emparro67 4-100-240/24Emparro67 4-100-240/24
OUTPUTOUTPUT
__
+
____
+
IND.CONT.EQ.61RM
TcIP67
N
L
N
L
9
(DC+/-24V)
(DC48V)
( C)°(°C)
0
(A)
-40 -20 0 20 40 60 80 100-40 -20 0 20 40 60 80 100
1
2
3
4
5
6
6
A
A
__
+
____
+
N / DC-
L / DC+
/ColorImageDict > /JPEG2000ColorACSImageDict >
/JPEG2000ColorImageDict > /AntiAliasGrayImages false
/DownsampleGrayImages true /GrayImageDownsampleType /Bicubic
/GrayImageResolution 1200 /GrayImageDepth -1
/GrayImageDownsampleThreshold 10.00000 /EncodeGrayImages true
/GrayImageFilter /DCTEncode /AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict >
/GrayImageDict > /JPEG2000GrayACSImageDict >
/JPEG2000GrayImageDict > /AntiAliasMonoImages false
/DownsampleMonoImages true /MonoImageDownsampleType /Bicubic
/MonoImageResolution 1200 /MonoImageDepth -1
/MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true
/MonoImageFilter /CCITTFaxEncode /MonoImageDict >
/AllowPSXObjects false /PDFX1aCheck false /PDFX3Check false
/PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true
/PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [
0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile ()
/PDFXOutputCondition () /PDFXRegistryName (http://www.color.org)
/PDFXTrapped /Unknown
/Description >>> setdistillerparams>
setpagedevice