Maximum pressure tightnes optimal after min. 24h! DISCLAIMER (For GK Packing System Mounting Instruction) ”The GK cable and pipe entry sealing system (“the GK Packing System”) is manufactured by Roxtec. This GK Packing System is a modular based system of sealing products consisting of different compo- nents. Each and every one of the components is necessary for the best performance of the GK Packing System. It has been certified to resist a number of different hazards. Any such certification, and the ability of the GK Packing System to resist such hazards, is dependent on all components that are installed as a part of the GK Packing System. Thus, the certification is not valid and does not apply unless all components installed as part of the GK Packing System are manufactured by or under license from Roxtec (“authorized manufacturer”). Roxtec gives no performance guarantee with respect to the GK Packing System, unless (I) all components installed as part of the GK Packing System are manufactured by an authorized manufacturer and (II) the purchaser is in compliance with (a), and (b), below. (a) Du- ring storage, the GK Packing System or part thereof shall be kept indoors in its original packaging at room temperature. (b) Installation shall be carried out in accordance with GK Packing System installation instructions in effect from time to time. The product information provided by Roxtec does not release the purchaser of the GK Packing System, or part thereof, from the obligation to independently determine the suitability of the products for the intended process, installation and/or use. Roxtec gives no guarantee for the GK Packing System or any part thereof and assumes no liability for any loss or damage whatsoever, whether direct, indirect, consequential, loss of profit or otherwise, occurred or caused by the GK Packing System or installations containing components not manufactured by an authorized manufacturer. Roxtec expressly excludes any implied warranties of merchantability and fitness for a particular purpose and all other express or implied representations and warranties provided by statute or common law. User determines suitability of the GK Packing System for intended use and assumes all risk and liability in connection therewith. In no event shall Roxtec be liable for consequential, punitive, special, exemplary or incidental damages.” Roxtec GmbH Neuer Höltigbaum, 22143 Hamburg, GERMANY TEL + 49 (040) 657398-0, FAX + 49 (040) 657398-50 EMAIL [email protected], www.roxtec.de Disassembly / Reinstallation Carry out disassembly in reverse order from Fig. 8 to Fig. 4. For re-installed cables, Filling-modules should be replaced with the corresponding Half-modules. If the existing module is longer than 62 mm, all Filling-modules should be replaced! Please follow the mounting instruction in chronological order Fig. 4 to 8. Corresponding pipes in normal steel, stainless steel and aluminum are available for each Round Penetration to order. In case of customer using its own pipe, the inner diameter of the tube nozzle should be given in order for us to adjust the round penetration accordingly. 5 8 6 Lubricate all contact surfaces of the module. You can combine different module sizes (+/- Module Size) Quadratic packing surface should be completely filled, eventually with Full Modules if needed. Do not use and Stay Plates or Tween Plates. Completely close the Metal Fittings. Constant tightening of the nuts until all gaps and columns are closed. At this point the cables should no longer move. 7 1 2 3 4 Clean the sleeves thoroughly before assembly. Do not lubricate or grease the surface! One or double-sided partition (can be ordered at Roxtec GmbH) enables retrofitting / subsequent installation. Intersections should be lubricated / greased! Opening the metal fittings, pulling the cables, lubricate/grease the square packing area. Measuring the middle cable diameter and selecting the appropriate modules. Please see the inner nominal diameter module. Validity: Bulkhead and deck - installation of fire classification A [0-15-30-60] according to IMO Resolution A.754 (18); applies for all GK round seals from sizes 50 to 200. Technical descriptions are described in our current GK packing system catalog. We have taken into account the VG88717 standards for navy projects applications. Local demands and standards are to be observed by the installers. Please follow the GK welding instructions and fire insulation assembly (acc. to actual certification). Use GK planning sheets or GK Software tool before cable installation and refer to actual information on www.gkmarine.de. Mounting Instruction GK round seals Typ RM 50-200 mm Subject to technical changes and errors. 12-2013/EN/1-1 Roxtec ® is a registered trademark of Roxtec in Sweden and/or other countries.