Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2011-02-01 to 2011-02-28 Register issued on : 2011-03-03 A list of subsectors can be found at the end of this document.
Information procedure Page 1
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Register issued on : 2011-03-03
A list of subsectors can be found at the end of this document.
Information procedure Page 2
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector A : SERVICES
Register issued on : 2011-03-03
Page 3Subsector A01: TOURIST SERVICES
Subsector : A01 Registration Date : 2011-02-08Organization : AENORCountry : Spain Latest Date for Comments : 2011-03-19Project ID : P0036557/0002 Draft for public enquiryICS :National Ref : PNE 187002:2008/1MTitle : Natural protected areas. Service provision requirements.Scope : This standard specifies the service provision requirements in natural protected areas.
Relatedness :National : REV/AMD UNE 187002:2008
** End of Subsector **
Subsector A02: CLEANING SERVICES
Subsector : A02 Registration Date : 2011-02-08Organization : EVSCountry : EstoniaProject ID : 00101210/0001 Project EstablishedICS : 03.080.10, 03.080.30National Ref : project 101210Title : Cleaning quality – System for establishing and assessing cleaning qualityScope : This standard describes a system for establishing and assessing cleaning quality. It is based
on the general principles stipulated in EN 13549:2001. The standard describes visual inspection and inspection using measuring instruments. The instrument measuring methods may work as a supplement for special types of premises used for e.g. the production of electronics. The indoor air quality is particularly affected by dust. In order to achieve an acceptable indoor air quality, it may become necessary to stipulate special requirements as regards dust. This is done by using dust measurements. The system can be used in various ways: for inspecting the cleaning quality achieved; for assessing the soiling level and/or the rate of re-soiling; for assessing the cleaning activity necessary to achieve a given level of quality; for establishing the cleaning quality achieved in relation to the cleaning activity. This standard describes exclusively the application of the measuring system for specifying a required quality and for inspecting the cleaning quality achieved. The standard can be used in all types of buildings and localities. The standard describes the result achieved immediately after cleaning has been completed. The standard does not comprise the measurement and control of cleaning-related services, such as replenishing lavatory articles etc.
Relatedness :National : New
** End of Subsector **
Subsector A09: FACILITY MANAGEMENT
Subsector : A09 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst11688/0001 Project EstablishedICS : 03.080.30National Ref :Title : Pickle Factories- General Rules
Page 4
Scope : This standard includes rules for physical characteristics, technical equipment, personel and certification of pickle factories.
Relatedness :National : New
Subsector : A09 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst11689/0001 Project EstablishedICS : 03.080.30National Ref :Title : Work places – Brine olive factories – General rulesScope : This standard includes general rules for structural characteristics, management and
technical equipment of brine olive factories
Relatedness :National : New
Subsector : A09 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst12076/0001 Project EstablishedICS : 03.080.30National Ref :Title : Plant For Processing And/Or Packing Tea Scope : This standard covers the general rules for the plants which process and/or pack up tea.
Relatedness :National : New
** End of Subsector **
Subsector A99: UNDETERMINED
Subsector : A99 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst07038/0002 Project EstablishedICS : 03.080.30National Ref :Title : Work places – Fishery products shops – General rulesScope : This standard includes the general for classification, structural characteristics, management
and thecnical characteristics of Döner production places thecnical characteristics of Döner production places technical equipment of fishery products shops.
Relatedness :National : New
Subsector : A99 Registration Date : 2011-02-02Organization : TSE
Page 5
Country : TurkeyProject ID : tst09094/0001 Project EstablishedICS :National Ref :Title : Work places –Beverage factories-General rulesScope : This standard includes rules for physical characteristics, technical equipment, personel and
certification of beverage factories
Relatedness :National : New
Subsector : A99 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst11138/0001 Project EstablishedICS : 03.080.30National Ref :Title : Work places – Tripe dealers- General rulesScope : This standard includes the general for classification, structural characteristics, management
and thecnical characteristics of Döner production places thecnical characteristics of Döner production places technical equipment of tripe dealers.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 6
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector B : BUILDING AND CONSTRUCTION
Register issued on : 2011-03-03
Page 7Subsector B01: FIRE PROTECTION
Subsector : B01 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 03100770/0001 Project EstablishedICS :National Ref : 03100770Title : Graphical symbols for fire-brigade - Part 6: Equipments in buildings; Amendment A2
Relatedness :National : New
Subsector : B01 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001627/0001 Project EstablishedICS : 13.220.20National Ref : NEN 2654-1:2011 Concept nlTitle : Management, control and maintenance of fire safety systems - Part 1: Fire detection
and alarm systemsScope : This standard gives requirements for management, control and maintenance of fire
detection and alarm systems. This standard is applicable to autonomous fire detection and alarm systems in offices, homes for the elderly, hotels, hospitals and industrial buildings.
Relatedness :National : New
Subsector : B01 Registration Date : 2011-02-23Organization : SUTNCountry : SlovakiaProject ID : 92100611/0001 Project EstablishedICS : 13.220.50, 91.120.01National Ref : STN 92 0251Title : Fire safety of buildings. Building occupation
Relatedness :National : REV/AMD STN 73 0818
Subsector : B01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173156/0001 Project EstablishedICS :National Ref : PR NF S61-759/A2Title : Firefighting equipment - Fire risers (dry and water based) - Installation and maintenance
Relatedness :National : New
** End of Subsector **
Subsector B02: STRUCTURES
Page 8
Subsector : B02 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023754/0001 Project EstablishedICS : 13.220.50, 91.010.30, 91.080.20National Ref : ÖNORM B 1995-1-2Title : Eurocode 5: Design of timber structures - Part 1-2: General - Structural fire design -
National specifications, national comments and national supplements concerning ÖNORM EN 1995-1-2
Scope : This Austrian Standard specifies national parameters to ÖNORM EN 1995-1-2 and shall be applied jointly with ÖNORM EN 1995-1-2 in Austria. EN 1995-1-2 deals with the design of timber structures for the accidental situation of fire exposure and is intended to be used in conjunction with EN 1995-1-1 and EN 1991-1-2:2002. EN 1995-1-2 only identifies differences from, or supplements normal temperature design. EN 1995-1-2 deals only with passive methods of fire protection. Active methods are not covered. EN 1995-1-2 applies to building structures that are required to fulfil certain functions when exposed to fire, in terms of avoiding premature collapse of the structure (load-bearing function); limiting fire spread (flames, hot gases, excessive heat) beyond designated areas (separating function). EN 1995-1-2 gives principles and application rules for designing structures for specified requirements in respect of the aforementioned functions and levels of performance. EN 1995-1-2 applies to structures or parts of structures that are within the scope of EN 1995-1-1 and are designed accordingly. The methods given in EN 1995-1-2 are applicable to all products covered by product standards made reference to in this Part.
Relatedness :National : New
Subsector : B02 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001626/0001 Project EstablishedICS : 93.040National Ref : NEN 6786:2011 Concept nlTitle : Rules for the design of movable bridgesScope : This standard contains technical determinations for the design of all types of revolving
bridges for road and rail traffic.
Relatedness :National : New
Subsector : B02 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001629/0001 Project EstablishedICS : 93.040National Ref : NEN 6787:2011 Concept nlTitle : Design of movable bridges - SafetyScope : This Dutch standard contains specifications and recommendations for a safe design of
movable bridges to attain safety for persons and posessions during the whole life cycle of the bridge. Specifications and recommendations related to the constructive design are mentioned in NEN 6786.
Relatedness :National : New
Page 9
Subsector : B02 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-03-31Country : Czech Republic Latest Date for Comments : 2011-05-31Project ID : 73000911/0001 Project EstablishedICS :National Ref :Title : Small, multi-storey and undergroung garagesScope : Revision of ČSN 73 6057:1987 and ČSN 736058:1987 Small, multi-storey and undergroung
garages. Joinder into one’s standard and connection with new technical findings and analyses
Relatedness :National : REV/AMD ČSN 73 6057:1987 and ČSN 736058:1987
Subsector : B02 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-06-01Country : Czech Republic Latest Date for Comments : 2011-09-30Project ID : 73002311/0001 Project EstablishedICS :National Ref :Title : Eurocode 2 – Design of concrete structures – Part 2: Concrete bridges – Design and
detailing rulesScope : Specification National Annex on CSN EN 1992-2 for design and detailing rules for concrete
bridges.
Relatedness :National : REV/AMD CSN EN 1992-2 (2007)
Subsector : B02 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-02-01Country : Czech Republic Latest Date for Comments : 2011-04-30Project ID : 73013910/0001 Draft for public enquiryICS :National Ref :Title : Design of masonry bridge structuresScope : The aim of the revision is up-dating of the standard in the connection with the
implementation of European Standards into ČSN.
Relatedness :
National :
REV/AMD CSN 73 6213 (1995)
Subsector : B02 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-04-01Country : Czech Republic Latest Date for Comments : 2011-05-30Project ID : 74000310/0001 Project EstablishedICS :National Ref :
Page 10
Title : Post-tensioning systems - General requirements and testsScope : The aim of the revision is unification of related Czech Standards. Use of new information
for post tensioning systems.
Relatedness :National : REV/AMD CSN 74 2871 (1996)
Subsector : B02 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-02-01Country : Czech Republic Latest Date for Comments : 2011-03-31Project ID : 75004110/0001 Draft for public enquiryICS :National Ref :Title : Small water reservoirsScope : The aim of the revision is up-dating of the standard in the connection with the
implementation of European Standards into ČSN and according to the contemporary state of art.
Relatedness :
National :REV/AMD CSN 75 2410 (1997)
** End of Subsector **
Subsector B03: CONCRETE
Subsector : B03 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100118/0001 Project EstablishedICS :National Ref : BS 8500-2:2006+A1Title : Concrete. Complementary British Standard to BS EN 206-1. Part 2. Specification for
constituent materials and concrete. Amendment
Relatedness :National : New
Subsector : B03 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100203/0001 Project EstablishedICS :National Ref : BS 8500-1:2006+A1Title : Complementary British Standard to BS EN 206-1. Part 1. Method of specifying and
guidance for the specifier. Amendment
Relatedness :National : New
Subsector : B03 Registration Date : 2011-02-02Organization : BSICountry : United Kingdom
Page 11
Project ID : 01100242/0001 Project EstablishedICS :National Ref : BS 5896Title : High tensile steel wire and strand for the prestressing of concrete. Specification
Relatedness :National : New
Subsector : B03 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173160/0001 Project EstablishedICS :National Ref : PR XP P18-462Title : Testing hardened concrete - Chloride ions migration accelerated test in non-steady-
state - Determining chloride ions diffusivity coefficient
Relatedness :National : New
Subsector : B03 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173161/0001 Project EstablishedICS :National Ref : PR XP P18-461Title : Testing hardened concrete - Chloride ions migration accelerated test in steady state -
Determining the real chloride ions diffusion coefficient
Relatedness :National : New
** End of Subsector **
Subsector B05: FIRE TESTS
Subsector : B05 Registration Date : 2011-02-24Organization : LSTCountry : LithuaniaProject ID : 10000785/0001 Project EstablishedICS : 13.220.50National Ref :Title : Reaction to fire tests. Method for determining combustibility characteristics Scope : This test method is applicable to solid non-metallic materials, including building materials
and products (hereinafter - the material) containing more than 3% of organic material and does not apply to materials with one-sided finish or non-combustible cover. This test method is intended for determination of material flammability characteristics (weight loss and temperature increase) in research and control work and is not intended for classification of building materials according to LST EN 13501-1.
Relatedness :National : New
Page 12
Subsector : B05 Registration Date : 2011-02-24Organization : LSTCountry : LithuaniaProject ID : 10000786/0001 Project EstablishedICS : 13.220.50National Ref :Title : Reaction to fire tests. Method for determining the flame spread index and evaluation Scope : This test method is applicable to solid materials, including building materials and products
(hereinafter - the materials) to identify the flame spread index and to assess the test results. The test method can be applied to laminates, decorative coatings and substances in non-combustible, but painted or otherwise coated surfaces. This test method is intended for determination of flame spread index through investigative and inspection work and is not intended for classification of building materials and products according to LST EN 13501-1.
Relatedness :National : New
Subsector : B05 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-03-01Country : Czech Republic Latest Date for Comments : 2011-04-30Project ID : 73001111/0001 Project EstablishedICS :National Ref :Title : Fire protection of buildings - Changes of buildingsScope : The aim of the modification is complement of values of fire resistance of engineering
structures.
Relatedness :National : REV/AMD CSN 73 0834 (2011)
** End of Subsector **
Subsector B06: GYPSUM
Subsector : B06 Registration Date : 2011-02-01Organization : AENORCountry : SpainProject ID : P0037048/0001 Project EstablishedICS :National Ref : PNE 102042Title : Gypsum plasters. Other test methods.Scope : This standard describes the reference test methods for gypsum plasters not included in the
EN 13279-2
Relatedness :National : REV/AMD UNE 102032:1984, UNE 102032:1999, UNE 102039:1985
** End of Subsector **
Subsector B11: METAL STRUCTURES
Subsector : B11 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-02-01
Page 13
Country : Czech Republic Latest Date for Comments : 2011-03-31Project ID : 73011010/0001 Draft for public enquiryICS :National Ref :Title : Execution of steel bridge structuresScope : The aim of the revision is up-dating of the standard in the connection with the
implementation of European Standards into ČSN This work follows the analysis study RU/0854/08.
Relatedness :
National :REV/AMD CSN 73 2603 (1996)
** End of Subsector **
Subsector B12: MASONRY
Subsector : B12 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023764/0001 Project EstablishedICS : 91.010.30, 91.080.30National Ref : ONR 21996Title : Design of masonry structures - Simplified calculation methods for unreinforced masonry
structures following ÖNORMen EN 1996-3 and B 1996-3Scope : The ONR 21996 provides simplified calculation methods according to EN 1996-3 to
facilitate the design of the following unreinforced masonry walls, subject to certain conditions of application: -vertical and earthquake loading walls with wind loading; -walls subjected to concentrated loads; -shear walls; -basement walls subjected to lateral earth pressure and vertical loads; -walls subjected to lateral loads but not subjected to vertical loads; -attestation of existing projects and existing structural elements of masonry. The rules given in ONR 21996 are consistent with those given in EN 1996-1-1, but are more conservative in respect of the conditions and limitations of their use. For those types of masonry structure or parts of structures not covered by scope, the design shall be based on EN 1996-1-1. This ONR 21996 applies only to those masonry structures, or parts thereof, that are described in EN 1996-1-1 and EN 1996-2.
Relatedness :National : New
Subsector : B12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 00515548/0001 Project EstablishedICS :National Ref : 00515548Title : Clay masonry units - Part 7: Clay masonry units with specific thermal insulating
properties
Relatedness :National : New
Subsector : B12 Registration Date : 2011-02-02Organization : BSI
Page 14
Country : United KingdomProject ID : 01100048/0001 Project EstablishedICS :National Ref : BS 8221-2Title : Code of practice for cleaning and surface repair of buildings. Part 2. Surface repair of
natural stones, brick and terracotta
Relatedness :National : New
Subsector : B12 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100114/0001 Project EstablishedICS :National Ref : BS 8221-1Title : Code of practice for cleaning and surface repair of buildings. Part 1. Cleaning of natural
stones, brick terracotta and concrete
Relatedness :National : New
** End of Subsector **
Subsector B14: GEOTECHNICS
Subsector : B14 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023794/0001 Project EstablishedICS :National Ref : ONR 24406-1Title : Assessment of underground with regard to explosive ordnance - Part 1: Estimate of
hazards, measures and methods for recovery of explosive ordnanceScope : This ON-Rule defines the procedure for investigating, locating, uncovering and retrieving
explosive ordnance in soil and water and describes the applicable methods.
Relatedness :National : New
** End of Subsector **
Subsector B18: SCAFFOLDING
Subsector : B18 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100034/0001 Project EstablishedICS :National Ref : BS 5975:2008+A1Title : Code of practice for temporary works procedures and the permissible stress design of
falsework. Amendment
Relatedness :National : New
Page 15** End of Subsector **
Subsector B20: DRAINAGE EQUIPMENT
Subsector : B20 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100158/0001 Project EstablishedICS :National Ref : BS 5911-3:2010+A1Title : Concrete pipes and ancillary concrete products. Part 3. Specification for unreinforced
and reinforced manholes and soakaways (complementary to BS EN 1917:2002). Amendment
Relatedness :National : New
Subsector : B20 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2010-11-30Country : Czech Republic Latest Date for Comments : 2011-04-01Project ID : 75004710/0001 Project EstablishedICS :National Ref :Title : Prevention of surface and ground water contamination caused by road transport of oil
and oil-derived productsScope : The aim of the revision is unification of terminology with contemporary legislation.
Relatedness :National : REV/AMD ČSN 75 3418 (1987)
** End of Subsector **
Subsector B23: DISTRICT HEATING
Subsector : B23 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-04-01Country : Czech Republic Latest Date for Comments : 2011-06-30Project ID : 73000811/0001 Project EstablishedICS :National Ref :Title : Space arrangement of conduit of technical equipmentScope : The aim of the revision is unification of related Czech Standards. Use of new information
for space arrangement of conduit of technical equipment.
Relatedness :National : REV/AMD CSN 73 6005 (1994)
** End of Subsector **
Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT
Subsector : B25 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001628/0001 Project EstablishedICS : 91.140.40
Page 16
National Ref : NPR 3378-80:2011 Concept nlTitle : Guidelines for NEN 1078 - Part 80: Classification of gas appliancesScope : In this part a description is given of the meaning of CE marking, classification of gas
appliances and the designation of gas, as mentioned on the appliance and manual of the manufacturer.
Relatedness :National : New
** End of Subsector **
Subsector B26: ROAD BUILDING AND MAINTENANCE
Subsector : B26 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023755/0001 Project EstablishedICS : 93.080.20National Ref : ÖNORM B 3585Title : Bituminous mixtures - Material specifications - Mastic asphalt - Rules for the
implementation of ÖNORM EN 13108-6Scope : This Austrian Standard specifies selected requirements for mastic asphalt intended for
construction of roads, airports and other traffic areas complying with ÖNORM B 3130, ÖNORM EN 13108-6, ÖNORM EN 13108-20 and ÖNORM EN 13108-21, based on the specific geographic, topographic and climatic conditions in Austria. The present Austrian Standard shall be applied jointly with these above mentioned Standards. In order to cover the load situation in Austria, different types of mixtures, related to the mixture composition and requirements for aggregates, are defined.
Relatedness :National : New
Subsector : B26 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023757/0001 Project EstablishedICS : 93.080.20National Ref : ÖNORM B 3587Title : Bituminous mixtures - Material specifications - Cold asphalt (CA) - Rules for the
implementation of ÖNORM EN 13108-7Scope : This Austrian Standard specifies selected requirements for cold asphalt intended for
construction of roads, airports and other traffic areas complying with ÖNORM B 3130, ÖNORM EN 13108-7, ÖNORM EN 13108-20, ÖNORM EN 13808 and ÖNORM EN 15322, based on the specific geographic, topographic and climatic conditions in Austria. The present Austrian Standard shall be applied jointly with these above mentioned Standards. In order to cover the load situation in Austria, different types of mixtures, related to the mixture composition and requirements for aggregates, are defined.
Relatedness :National : New
Subsector : B26 Registration Date : 2011-02-23Organization : SUTNCountry : Slovakia
Page 17
Project ID : 73101111/0001 Project EstablishedICS : 19.060, 75.140, 93.080.10, 93.080.20National Ref : STN 73 6127-1 Title : Road Building. Grouted courses. Part 1: Penetration macadam Scope : STN 73 6127:1996 contains six technologies from which three are out of date and they are
not used in practice. Standard revision is required in regard to European standards implementation into Slovak standards system (STN EN 13043 - aggregate, STN EN 12591 - asphalt, STN EN 13108 –20 and 21).
Relatedness :National : REV/AMD STN 73 6127
Subsector : B26 Registration Date : 2011-02-23Organization : SUTNCountry : SlovakiaProject ID : 73101211/0001 Project EstablishedICS : 19.060, 75.140, 93.080.10, 93.080.20National Ref : STN 73 6127-2 Title : Road Building. Grouted courses. Part 2: Cement macadam courseScope : STN 73 6127:1996 requires complex revision. European standards regarding to aggregates
and asphalt binders have to be respected. STN 73 6127 contains six separate technologies, from which three are out of date already and they are not used
Relatedness :National : REV/AMD STN 73 6127
Subsector : B26 Registration Date : 2011-02-23Organization : SUTNCountry : SlovakiaProject ID : 73101311/0001 Project EstablishedICS : 19.060, 75.140, 93.080.10, 93.080.20National Ref : STN 73 6127-3 Title : Road Building. Grouted courses. Part 3: Asphalt - cement concreteScope : STN 73 6127 valid from April 1996 contains six technologies, from which three are out of
date and they are not used in practice. Standard revision is required in regard of European standards implementation into Slovak standards system (STN EN 13043 - aggregate, STN EN 12591 - asphalt, STN EN 13108 -20).
Relatedness :National : REV/AMD STN 73 6127
** End of Subsector **
Subsector B27: WATERPROOFING MATERIALS
Subsector : B27 Registration Date : 2011-02-03Organization : UNMZ Draft Issue Date : 2011-03-01Country : Czech Republic Latest Date for Comments : 2011-04-30Project ID : 73016310/0001 Project EstablishedICS :National Ref :Title : Waterproofing of buildings - Discontinuous roofingScope : The aim of the new standard is unification of requirements for discontinuous foofing for
Page 18
Scope : waterproofing of buildings.
Relatedness :National : New
Subsector : B27 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 87025610/0001 Project EstablishedICS : 91.060.20National Ref : U87025610Title : Fibre cement profiled sheets roof coverings - Instructions for design, installation and
maintenanceScope : The standard defines common criteria for design, installation and maintenance of
discontinuous roofings made of fibre-cement flat, profiled or curved sheets.
Relatedness :National : REV/AMD UNI 10636:2005
Subsector : B27 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037235/0001 Project EstablishedICS :National Ref : PNE 104317Title : Waterproofing. Plunger range determination before the perforation of the waterproofing
synthetic geomembranes for water reservoirsScope : This standard defines a test method to determinate the plunger range before the
perforation if the waterproofing synthetic geomembranes for water reservoirs starts
Relatedness :National : New
** End of Subsector **
Subsector B30: FLOOR AND SURFACING
Subsector : B30 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037114/0001 Project EstablishedICS :National Ref : PNE 41959-2Title : Sport surfaces of natural turf. Part 2: Automatic irrigation systems for football and rugby
natural turf surfaces.Scope : the aim of this standard is to be a guide for the installations of irrigations systems in natural
grass sports surfaces.
Relatedness :National : REV/AMD UNE 41959-2:2002 IN
Subsector : B30 Registration Date : 2011-02-28Organization : AENOR
Page 19
Country : SpainProject ID : P0037115/0001 Project EstablishedICS :National Ref : PNE 41959-3Title : Sport surfaces of natural turf. Part 1: Construction systems for sport surfaces of football,
rugby and golf.Scope : the aim of this standard is to develop laboratory tests to evaluate the natural grass sports
surfaces for football, rugby and golf.
Relatedness :National : REV/AMD UNE 41959-1:2002 IN
** End of Subsector **
Subsector B31: HEATING SYSTEMS IN BUILDINGS
Subsector : B31 Registration Date : 2011-02-25Organization : SNV Draft Issue Date : 2011-02-24Country : Switzerland Latest Date for Comments : 2011-05-18Project ID : CH110006/0001 Draft for public enquiryICS : 91.140.30National Ref : SIA 382/1Title : Ventilation and air conditioning systems - General principles and requirements
Relatedness :National : REV/AMD SIA 382/1 (2007)
** End of Subsector **
Subsector B33: BUILDING DESIGN
Subsector : B33 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 61002720/0001 Project EstablishedICS : 91.040.10National Ref : U61002720Title : Spectator facilities - Separating elements - Explanation of some aspects of UNI EN
13200-3Scope : This technical report gives explanations and help the right application of standard UNI EN
13200-3 applicable to separating elements.
Relatedness :National : New
** End of Subsector **
Subsector B99: UNDETERMINED
Subsector : B99 (Secondary Subsector)
Registration Date : 2011-02-02
Organization : BSICountry : United KingdomProject ID : 01100017/0001 Project EstablishedICS :National Ref : BS 7000-4
Page 20
Title : Design management systems. Part 4. Guide to managing design and construction
Relatedness :National : New
Subsector : B99 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001625/0001 Project EstablishedICS : 93.080.30National Ref : NEN 3381:2002 Concept nlTitle : Road traffic signs - Additional requirements for fixed traffic signsScope : This standard contains additional Dutch specifications for traffic signs to EN 12899-1:2007
"Fixed signs", concerning dimensions, materials, colours and light characteristics of retroreflective and general materials for traffic signs.
Relatedness :National : New
Subsector : B99 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 87005621/0001 Project EstablishedICS : 91.010.30National Ref : U87005621Title : Building and civil engineering works - Codification criteria for construction products and
works, activities and resources - Identification, description and interoperability - Denomination criteria according to UNI 11337
Scope : The Technical Specification specifies the denomination criteria in order to be in accordance with the codification criteria for construction products and works, activities and resources to identify univocally any subject and/or action within the construction process (i.e. from planning and design to execution and maintenance) as given in UNI 11337.
Relatedness :National : New
Subsector : B99 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 87005622/0001 Project EstablishedICS : 91.010.30National Ref : U87005622Title : Building and civil engineering works - Codification criteria for construction products and
works, activities and resources - Identification, description and interoperabilit - Collection and recording criteria for the technical information according to UNI 11337 – Qualification and quantification: format of the technical data sheets
Scope : The Technical Specification specifies the criteria for the collection and recording of the technical information into the technical data sheets in order to be in accordance with the codification criteria for construction products and works, activities and resources to identify univocally any subject and/or action within the construction process (i.e. from planning and design to execution and maintenance) as given in UNI 11337.
Relatedness :
Page 21
National : New
Subsector : B99 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 87005630/0001 Project EstablishedICS : 91.010.20National Ref : U87005630Title : Construction works - Financing rules - Homogeneous criteria and parameters for
economincal and financial managementScope : This standard specifies the criteria regarding to the conformity among work project,
bankability of the project and financial contract. It applies to new construction works regardless of the commitment, of the size and of the intended use of the work.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 22
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS
Register issued on : 2011-03-03
Page 23Subsector C01: Food products
Subsector : C01 Registration Date : 2011-02-11Organization : UNMZ Draft Issue Date : 2010-03-31Country : Czech Republic Latest Date for Comments : 2010-04-30Project ID : 56000411/0001 Published StandardICS :National Ref :Title : Fishes and aquatic animals - NomenclatureScope : Completion and review of trade names.
Relatedness :National : REV/AMD CSN 56 0634:2006
Subsector : C01 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 59098140/0001 Project EstablishedICS : 67.100.30National Ref : U59098140Title : Crescenza cheese or Stracchino cheese - Definition, composition and characteristicsScope : This standard specifies the commercial definition, raw materieals, production process and
characteristics of Crescenza or Stracchino cheese.
Relatedness :National : REV/AMD UNI 10535:1995
Subsector : C01 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 59108130/0001 Project EstablishedICS : 67.120.10National Ref : U59108130Title : Meat and meat products - Determination of total phosphorous content - Spectrometric
methodScope : This standard specifies a method for the determination of the total phosphorous content in
meat and meat products.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173011/0001 Project EstablishedICS :National Ref : V47-001/A1Title : Rabbit meats - Domestic rabbit meat production and processing - Amendment 1
Relatedness :National : New
Page 24
Subsector : C01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173157/0001 Project EstablishedICS :National Ref : PR NF V08-407Title : Microbiology of food products. Raw materials coming into the composition of canned
foods. Enumeration of the heat-resisting spores of bacillus and {Clostridium} thermophilus. Most probable number technique
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037281/0001 Project EstablishedICS :National Ref : PNE 195001:2008/1MTitle : Guide of good hygiene practices for primary production in fishing. Tides shorter than 48
h.Scope : This document modifies the paragraph 4.4.4 Stowage, third dash of the National standard
UNE 195001:2008
Relatedness :National : REV/AMD UNE 195001:2008
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1000893/0001 Project EstablishedICS : 67.200.10National Ref :Title : Edible Oils of Vegetable Origin (Not Subject of a Specific Standard) Scope : This standard applies to only edible oils of vegetable origin. It does not apply to oils which
lost its edible property or had no edible property and existence of its own sandard and marketing as its own name.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1001068/0001 Project EstablishedICS : 67.120.20National Ref :Title : Chicken Eggs in Shell Scope : This standard specifies requirements for chicken eggs in shell. It does not cover eggs in shell
of other poultry, eggs for incubation and processed eggs such as liquid, frozen, powdered etc.
Relatedness :
Page 25
National : New
Subsector : C01 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : t1001071/0001 Project EstablishedICS : 67.120.10National Ref :Title : Pastırma Scope : This standard covers pastırma.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1002284/0001 Project EstablishedICS : 67.060National Ref :Title : Boiled and pounded wheat Scope : This standard covers boıled and pounded wheat
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1002670/0001 Project EstablishedICS : 67.080.20National Ref :Title : Canned Green Beans With Vegetable Oil-ready to serve Scope : This standard comprise canned green beans with vegetable oil-ready to serve.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1006321/0001 Project EstablishedICS : 65.120National Ref :Title : Animal Feeds-Sugar Beet Pulp Scope : This standard applies to beet pulps obtained from sugar beet and used as animal feeds.
Relatedness :National : New
Page 26
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1007359/0001 Project EstablishedICS : 67.120.10National Ref :Title : Canned meat Scope : This standard, cavers canned meat
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1008596/0001 Project EstablishedICS : 65.120National Ref :Title : Animal Feeds - Corn Bran farine as by-products. It does not apply to the other by
products of corn. Scope : This standard applies to corn brans obtained during corn processing to starch and farine as
by-products. It does not apply to the other by products of corn.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t1013208/0001 Project EstablishedICS : 67.120.10National Ref :Title : Canned a stew made of meat and vegetables- Ready to serveScope : This standart contaın canned a stew made from meat and vegatables
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : t113209 /0001 Project EstablishedICS : 67.120.10National Ref :Title : Canned pheasant khebab - Ready to serve Scope : This standard specified canned pheasant khebap- ready to serve
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02
Page 27
Organization : TSECountry : TurkeyProject ID : t2000798/0001 Project EstablishedICS : 67.080.20National Ref :Title : Fresh Peas Scope : This standart applies to peas in clause 0.2.1 which is marketed to the consumer as fresh.
This standard not includes the processed products from peas.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : t2007440/0001 Project EstablishedICS : 67.120.10National Ref :Title : Meat broth products Scope : This standard, covers meat broth products.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t2009130/0001 Project EstablishedICS : 13.060.10National Ref :Title : Naturel mineral waterScope : This standard comprise natural mineral water. ıt doesn't comprise the water with medical
aim and medicine property, the water which is for treatment in welded joint, the thermal and water with mineral foundation , and the other drinking water.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : t2012980/0001 Project EstablishedICS : 67.060National Ref :Title : Mantı-Frozen Scope : This standards cover mantı. It Doesn't cover fresh mantı or baked mantı
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-08
Page 28
Organization : TSECountry : TurkeyProject ID : tst00208/0001 Project EstablishedICS : 67.120.10National Ref :Title : Intestines (Casings)Scope : This standard applies to casings obtained from heavy weight form animals and light weight
form animals. It does not apply easings obtained from camels, pigs, horses and dankeys.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : tst01204/0001 Project EstablishedICS :National Ref :Title : Prunes Scope : This standard applies to dried prunes in Prunes domestica L. Specy. It doesn’t apply other
prunes which their seed is taken and also specy machined and stuffed.
Relatedness :National : New
Subsector : C01 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : tst12526/0001 Project EstablishedICS : 67.180.10National Ref :Title : Mesir Putty
Relatedness :National : New
** End of Subsector **
Subsector C02: PAINTS AND RELATED PRODUCTS
Subsector : C02 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037261/0001 Project EstablishedICS :National Ref : PNE 48315Title : Paints and varnishes. Determination of anticorrosive properties of organic coatings by
the Accelerated Cyclic Electrochemical Technique (ACET). Part 1: Collection of data.Scope : This standard refers to the determination of anticorrosive properties of organic coating by
means of the Electrochemical Accelerated Cyclic Technique (ACET) The technology is based on the application of cycles consisting of sequences of EIS measures, cathode polarizations and potential relaxation on the tested systems accelerating its degradation.
Relatedness :
Page 29
National : New
** End of Subsector **
Subsector C03: CHEMISTRY
Subsector : C03 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037159/0001 Project EstablishedICS :National Ref : PNE 84082Title : Cosmetic raw materials. Toothpastes. Precipitated silica.Scope : This standard specifies the physic-chemical characteristics of the precipitated silica for
toothpastes cosmetic use.
Relatedness :National : REV/AMD UNE 84082:1997
** End of Subsector **
Subsector C11: TOBACCO
Subsector : C11 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst82971/0001 Project EstablishedICS : 65.160National Ref :Title : Tobacco products for pipe Scope : This standart includes Tobacco products for pipes.
Relatedness :National : New
Subsector : C11 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst82985/0001 Project EstablishedICS : 65.160National Ref :Title : Fine-cut smoking tobacco intended for the rolling of cigarettes Scope : This standart includes fine-cut smoking tobacco intended for the rolling of cigarettes
Relatedness :National : New
** End of Subsector **
Subsector C13: FERTILIZERS
Subsector : C13 Registration Date : 2011-02-25Organization : AFNORCountry : France
Page 30
Project ID : FA173159/0001 Project EstablishedICS :National Ref : PR NF U44-204Title : Fertilizers or liming material or liming material-fertilizer with agronomic additive . Types
and specifications
Relatedness :National : New
** End of Subsector **
Subsector C20: EXPLOSIVES AND FIREWORKS
Subsector : C20 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : tst83306/0001 Project EstablishedICS : 95.020National Ref :Title : Sympathetic Reaction, Munition Test ProceduresScope : The aim of this standard is to provide a standard test procedure to assess the potential for a
munition to sympathetically react to the initiation of an adjacent munition.
Relatedness :National : NewInternational : Modified Stanag 4396:2003
Subsector : C20 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : tst83307/0001 Project EstablishedICS : 95.020National Ref :Title : Shaped Charge jet, Munıtıons Test ProcedureScope : The aim of this standard is to provide a standard test procedure for determining the degree
of reaction, if any, of a munition when hit by a typical top attack bomblet shaped charge jet.
Relatedness :National : NewInternational : Modified Stanag 4526:2004
Subsector : C20 Registration Date : 2011-02-08Organization : TSECountry : TurkeyProject ID : tst83312/0001 Project EstablishedICS : 95.020National Ref :Title : Slow Heating, Munıtıons Test ProcedureScope : The aim of this standard is to provide a standard test procedure for assessing the reaction,
if any, of munitions and weapon systems to a gradually increasing thermal environment at a change rate of 3.3°C per hour.
Relatedness :National : New
Page 31
International : Modified STANAG 4382:2003
** End of Subsector **
** End of Sector **
Information procedure Page 32
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector F : FUNDAMENTAL STANDARDS
Register issued on : 2011-03-03
Page 33Subsector F05: MEASURING INSTRUMENTS
Subsector : F05 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100244/0001 Project EstablishedICS :National Ref : BS 8570Title : Code of practice. Installation of electrical resistance strain gauges
Relatedness :National : New
** End of Subsector **
Subsector F12: INFORMATION PROCESSING SYSTEMS
Subsector : F12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04300577/0001 Project EstablishedICS :National Ref : 04300577Title : Information technology: Office machines; Requirements and tests for the preparation of
refilled toner modules for electrofotografical printer, copiers and facsimile machines
Relatedness :National : New
Subsector : F12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04300582/0001 Project EstablishedICS :National Ref : 04300582Title : Information technology - Office machines, inkjet print heads and inkjet tanks for inkjet
printers - Part 1: Preparation of refilled inkjet print heads and inkjet tanks for inkjet printers
Relatedness :National : New
** End of Subsector **
Subsector F13: ENVIRONMENTAL TESTS
Subsector : F13 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100201/0001 Project EstablishedICS :National Ref : BS 1339-2:2009+Corrigendum 1Title : Humidity. Part 2. Humidity calculation and tables with user guide. Corrigendum
Relatedness :National : New
Page 34
** End of Subsector **
Subsector F15: MATERIAL TESTING IN GENERAL
Subsector : F15 (Secondary Subsector)
Registration Date : 2011-02-02
Organization : BSICountry : United KingdomProject ID : 01100201/0001 Project EstablishedICS :National Ref : BS 1339-2:2009+Corrigendum 1Title : Humidity. Part 2. Humidity calculation and tables with user guide. Corrigendum
Relatedness :National : New
Subsector : F15 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233634/0001 Project EstablishedICS :National Ref : 06233634Title : Testing of lubricants - Test methods - Part 1:...
Relatedness :National : New
Subsector : F15 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233637/0001 Project EstablishedICS :National Ref : 06233637Title : Testing of lubricants - Tribological test in the translatory oscillation apparatus - Part 4:
Determination of friction and wear data for lubricating oils with the cylindrical roller-disk geometry
Relatedness :National : New
** End of Subsector **
Subsector F16: GRAPHICAL SYMBOLS
Subsector : F16 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100202/0001 Project EstablishedICS :National Ref : BS 8569Title : Water safety signs. Guidance for use of coastal slipway safety signs and symbols
Relatedness :
Page 35
National : New
** End of Subsector **
Subsector F20: QUALITY ASSURANCE
Subsector : F20 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100043/0001 Project EstablishedICS :National Ref : BS 5760-24Title : Reliability of systems, equipment and components. Part 24. Integration of risk
assessment in the inspection and testing of complex systems
Relatedness :National : New
** End of Subsector **
Subsector F99: UNDETERMINED
Subsector : F99 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100017/0001 Project EstablishedICS :National Ref : BS 7000-4Title : Design management systems. Part 4. Guide to managing design and construction
Relatedness :National : New
Subsector : F99 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100335/0001 Project EstablishedICS :National Ref : BS 0Title : A standard for standards
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 36
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE
Register issued on : 2011-03-03
Page 37Subsector H04: SPORTS EQUIPMENT
Subsector : H04 Registration Date : 2011-02-21Organization : MSZT Draft Issue Date : 2011-05-21Country : HungaryProject ID : 34821201/0001 Project EstablishedICS : 97.220.10National Ref :Title : Water treatment and recirculation turnover of the swimming pool
Relatedness :National : REV/AMD MSZ 15234
Subsector : H04 Registration Date : 2011-02-21Organization : MSZT Draft Issue Date : 2011-05-21Country : HungaryProject ID : 34821202/0001 Project EstablishedICS : 97.220.10National Ref :Title : Pool basin. Technical requirements of construction and acceptance
Relatedness :National : REV/AMD MSZ 15233
** End of Subsector **
Subsector H09: FURNITURE
Subsector : H09 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100049/0001 Project EstablishedICS :National Ref : BS 7176:2007+A1Title : Specification for resistance to ignition of upholstered furniture for non-domestic seating
by testing composites. Amendment
Relatedness :National : New
Subsector : H09 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100050/0001 Project EstablishedICS :National Ref : BS 7177:2008+A1Title : Specification for resistance to ignition of mattresses, mattress pads, divans and bed
bases. Amendment
Relatedness :National : New
Subsector : H09 (Secondary Registration Date : 2011-02-02
Page 38
Subsector : Subsector) Registration Date :Organization : BSICountry : United KingdomProject ID : 01100243/0001 Project EstablishedICS :National Ref : BS 3379:2005+A1Title : Combustion modified flexible polyurethane cellular materials for loadbearing
applications. Specification. Amendment
Relatedness :National : New
** End of Subsector **
Subsector H12: CERAMIC AND GLASS WARE FOR FOOD
Subsector : H12 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100020/0001 Project EstablishedICS :National Ref : BS 6748:1986+A1Title : Specification for limits of metal release from ceramic ware, glassware, glass ceramic
ware and vitreous enamel ware. Amendment
Relatedness :National : New
Subsector : H12 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100047/0001 Project EstablishedICS :National Ref : BS 3828Title : Specification for crystal glass
Relatedness :National : New
** End of Subsector **
Subsector H25: LARGE GAS APPLIANCES
Subsector : H25 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04000238/0001 Project EstablishedICS :National Ref : 04000238Title : Equipment for commercial kitchens - Mobile equipment - Part 1: Runabout carts,
Requirements and testing
Relatedness :National : New
Page 39** End of Subsector **
Subsector H30: EQUIPMENT FOR CHILDREN
Subsector : H30 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172434/0001 Project EstablishedICS :National Ref : XP S64-065Title : Child use and care articles - High chairs for collective use
Relatedness :National : New
Subsector : H30 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172436/0001 Project EstablishedICS :National Ref : NF S54-042Title : Thermometers for bath - Temperature indicators - Specifications and marks
Relatedness :National : New
** End of Subsector **
Subsector H99: UNDETERMINED
Subsector : H99 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023767/0001 Project EstablishedICS : 65.020.30National Ref : ÖNORM S 1009Title : Private keeping of chinchillasScope : This ÖNORM describes the private keeping of chinchillas (including their keeping e.g. in
kindergartens and pensioners' residences), particularly concerning the condition and equipment of shelters and keeping systems. The objective of this ÖNORM is the optimization of keeping conditions under the aspect of appropriateness to the species [§ 13 Abs. 3 TSchG]. The keeping of these animals in the scope of business activities and animal shelters is not subject to this ÖNORM.
Relatedness :National : New
Subsector : H99 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04000234/0001 Project EstablishedICS :National Ref : 04000234Title : Methods for measuring of the energy use from equipment for commercial kitchens - Part
4: Convection ovens
Page 40
Relatedness :National : New
Subsector : H99 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04000235/0001 Project EstablishedICS :National Ref : 04000235Title : Methods for measuring of the energy use from equipment for commercial kitchens - Part
5: Tilting fry pans and stationary frying pans
Relatedness :National : New
Subsector : H99 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04000236/0001 Project EstablishedICS :National Ref : 04000236Title : Methods for measuring of the energy use from equipment for commercial kitchens - Part
6: Tilting pressure braising pans and stationary pressure braising pans
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 41
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector I : MECHANICAL ENGINEERING
Register issued on : 2011-03-03
Page 42Subsector I02: FASTENERS
Subsector : I02 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023758/0001 Project EstablishedICS : 01.040.21, 21.060.01National Ref : ÖNORM ISO 1891Title : Fasteners - TerminologyScope : This International Standard provides translation guidance for terms commonly used to
describe fasteners. This International Standard lays down the terminology of fasteners in English, French and Russian, recommended for use unless otherwise specified in the appropriate product standard.At present, not all of the fasteners listed are covered by ISO documents. For the main part, the items have been selected from existing national standards. Also included are obsolescent types (those being used up from stock) in order that their terminology may be standardized at the same time. The drawings are essentially diagrammatic, in particular those showing bolts and screws having special characteristics. In addition to terms used in the three official ISO languages (English, French and Russian), this International Standard gives the equivalent terms in Chinese, German, Italian, Japanese, Spanish, and Swedish.
Relatedness :National : New
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B470/0001 Project EstablishedICS : 21.060.01National Ref : U2404B470Title : Threaded tubular rivets with cylindrical headScope : This standard defines dimensions and technical requirements of threaded tubular rivets
with cylindrical head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9201:1988
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B480/0001 Project EstablishedICS : 21.060.01National Ref : U2404B480Title : Threaded tubular rivets with countersunk headScope : This standard defines dimensions and technical requirements of threaded tubular rivets
with countersunk head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9202:1988
Page 43
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B490/0001 Project EstablishedICS : 21.060.01National Ref : U2404B490Title : Threaded tubular rivets with plate edge headScope : This standard defines dimensions and technical requirements of threaded tubular rivets
with plate edge head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9203:1988
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B500/0001 Project EstablishedICS : 21.060.01National Ref : U2404B500Title : Blind threaded tubular rivets with cylindrical headScope : This standard defines dimensions and technical requirements of blind threaded tubular
rivets with cylindrical head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9204:1988
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B510/0001 Project EstablishedICS : 21.060.01National Ref : U2404B510Title : Blind threaded tubular rivets with countersunk headScope : This standard defines dimensions and technical requirements of blind threaded tubular
rivets with countersunk head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9205:1988
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B520/0001 Project EstablishedICS : 21.060.01National Ref : U2404B520Title : Blind threaded tubular rivets with plate edge head
Page 44
Scope : This standard defines dimensions and technical requirements of blind threaded tubular rivets with plate edge head with medium and fine closing thickness. These rivets are intended to be used in assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual or pneumatic equipments.
Relatedness :National : REV/AMD UNI 9206:1988
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B530/0001 Project EstablishedICS : 21.060.01National Ref : U2404B530Title : Blind threaded tubular rivets with plate edge head, hexagonal and semi hexagonal
shank Scope : This standard defines dimensions and technical requirements of blind threaded tubular
rivets with plate edge head, hexagonal and semi hexagonal shank, with medium and fine closing thickness. These rivets may be used as an alternative to the threaded tubular rivets with cylindrical head, when high rotation holding features are required. These rivets are particularly recommended for assemblings on tubolar and box-shielded parts. They can be used on metal sheets when tapping does not assure sufficient holding guarantee and to avoid on the same deep-drawing and following tapping operation. The mounting of these rivets is made with manual and pneumatic equipments.
Relatedness :National : REV/AMD UNI 10445:1995
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B540/0001 Project EstablishedICS : 21.060.01National Ref : U2404B540Title : Blind threaded tubular rivets with cylindrical head, hexagonal and semi hexagonal shankScope : This standard defines the dimensions and the technical requirements of blind threaded
tubular rivets with cylindrical head, hexagonal and semi hexagonal shank, with medium and fine closing thickness. These rivets may be used as an alternative to the threaded tubular rivets with cylindrical head, when high rotation holding features are required. These rivets are particularly recommended for assemblings on tubolar and box-shielded parts. They can be used on metal sheets when tapping does not assure sufficient holding guarantee and to avoid on the same deep-drawing and following tapping operation. The mounting of these rivets is made with manual and pneumatic equipments.
Relatedness :National : REV/AMD UNI 10446:1995
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B550/0001 Project EstablishedICS : 21.060.01
Page 45
National Ref : U2404B550Title : Threaded tubular rivets with plate edge head, hexagonal and semi hexagonal shank Scope : This standard defines the dimensions and the technical requirements of threaded tubular
rivets with plate edge head, hexagonal and semi hexagonal shank, with medium and fine closing thickness. These rivets may be used as an alternative to the threaded tubular rivets with cylindrical head, when high rotation holding features are required. These rivets are particularly recommended for assemblings on tubolar and box-shielded parts. They can be used on metal sheets when tapping does not assure sufficient holding guarantee and to avoid on the same deep-drawing and following tapping operation. The mounting of these rivets is made with manual and pneumatic equipments.
Relatedness :National : REV/AMD UNI 10447:1995
Subsector : I02 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 2404B560/0001 Project EstablishedICS : 21.060.01National Ref : U2404B560Title : Threaded tubular rivets with cylindrical head, hexagonal and semi hexagonal shankScope : This standard defines dimensions and technical requirements of threaded tubular rivets
with cylindrical head, hexagonal and semi hexagonal shank, with medium and fine closing thickness. These rivets may be used as an alternative to the threaded tubular rivets with cylindrical head, when high rotation holding features are required. These rivets are particularly recommended for assemblings on tubolar and box-shielded parts. The mounting of these rivets is made with manual and pneumatic equipments.
Relatedness :National : REV/AMD UNI 10448:1995
** End of Subsector **
Subsector I04: ROLLING BEARINGS
Subsector : I04 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023762/0001 Project EstablishedICS : 21.100.20National Ref : ÖNORM M 6324-2Title : Rolling bearings - Accessories - Snap rings and circular groovesScope : This ÖNORM defines the basic dimensions of snap rings and circular grooves. It applies to
the dimension series 18 and 19 as well as for the diameter series 0, 2, 3 and 4 (except the dimension series 00, 82 and 83). The sequence of snap rings and the dimensions of circular grooves shall be based on the nominal dimension of the outer diameter of the rolling bearing. Suffixes for circular grooves are defined in ÖNORM M 6317.
Relatedness :National : New
** End of Subsector **
Subsector I05: IRON PIPES
Page 46
Subsector : I05 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037282/0001 Project EstablishedICS :National Ref : PNE 19101Title : Ductile iron pipes, fittings, accessories and their joint for local and secondary water
pipelines. Requirements and test methodsScope : The Spanish standard specifies requirements and related test methods applicable to ductile
iron pipes, fittings and joints, pipes used as external to buildings, and local high schools, according to EN 805 standard details. This standard applies to pipes, fittings and accessories: made plain end and hood; provided internal and external coating; to transport fluids between 0 and 30 ° C, excluding freezing and in areas where not applicable regulations on fire.
Relatedness :National : New
** End of Subsector **
Subsector I09: SMALL TOOLS
Subsector : I09 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173164/0001 Project EstablishedICS :National Ref : PR NF E67-002Title : Additive manufacturing - Model for specifications for the acceptance of piece
Relatedness :National : New
Subsector : I09 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173165/0001 Project EstablishedICS :National Ref : PR NF E67-001Title : Additive manufacturing - Vocabulary
Relatedness :National : New
** End of Subsector **
Subsector I12: PULLEYS & BELTS
Subsector : I12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04500234/0001 Project EstablishedICS :National Ref : 04500234Title : Conveyor belts with textile plies for bulk goods; dimensions, specifications, marking
Page 47
Relatedness :National : New
Subsector : I12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04500235/0001 Project EstablishedICS :National Ref : 04500235Title : Conveyor belts with textile plies for bulk goods; testing
Relatedness :National : New
Subsector : I12 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 04500236/0001 Project EstablishedICS :National Ref : 04500236Title : Conveyor belts with textile plies for bulk goods; permanent joints
Relatedness :National : New
** End of Subsector **
Subsector I18: MINING
Subsector : I18 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 00802217/0001 Project EstablishedICS :National Ref : 00802217Title : Investigations of raw material in hard-coal-mining - Part 1: Survey
Relatedness :National : New
** End of Subsector **
Subsector I19: NUCLEAR ENERGY
Subsector : I19 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233628/0001 Project EstablishedICS :National Ref : 06233628Title : Ventilating components in nuclear facilities
Relatedness :
Page 48
National : New
Subsector : I19 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233650/0001 Project EstablishedICS :National Ref : 06233650Title : Shielding walls against ionizing radiation - Recommendations for the construction of
walls made of lead bricks
Relatedness :National : New
Subsector : I19 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233651/0001 Project EstablishedICS :National Ref : 06233651Title : Radioisotope laboratories - Part 1: Rules for design; examples for application
Relatedness :National : New
Subsector : I19 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172433/0001 Project EstablishedICS :National Ref : PR NF M60-771Title : Nuclear energy - Measurement of the environnemental radioactivity - Air - Radon 222 in
the buildings : methodologies applies for the screening and for the complementary investigations
Relatedness :National : REV/AMD NF M60-771:200309 (M60-771)
** End of Subsector **
Subsector I20: REFRIGERATION
Subsector : I20 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037284/0001 Project EstablishedICS :National Ref : PNE 100715-1Title : Guide for the design, implementation and monitoring of a geothermal system. Part 1:
Vertical closed circuit systemsScope : This Spanish standard gives guidelines of good practices for the design, implementation and
monitoring of a geothermal system. This part of the standard specify the requirements for vertical closed circuit systems
Page 49
Relatedness :National : New
** End of Subsector **
Subsector I99: UNDETERMINED
Subsector : I99 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 01200341/0001 Project EstablishedICS :National Ref : 01200341Title : Support rings for carbon and stainless steel agitator vessels - Position
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 50
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector M : METALLIC MATERIALS
Register issued on : 2011-03-03
Page 51Subsector M01: STEEL
Subsector : M01 (Secondary Subsector)
Registration Date : 2011-02-02
Organization : BSICountry : United KingdomProject ID : 01100242/0001 Project EstablishedICS :National Ref : BS 5896Title : High tensile steel wire and strand for the prestressing of concrete. Specification
Relatedness :National : New
** End of Subsector **
Subsector M05: WELDING
Subsector : M05 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100113/0001 Project EstablishedICS :National Ref : BS 7910Title : Guide to methods for assessing the acceptability of flaws in metallic structures
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 52
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector N : NON-METALLIC MATERIALS
Register issued on : 2011-03-03
Page 53Subsector N01: PAPER AND BOARD
Subsector : N01 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037107/0001 Project EstablishedICS :National Ref : PNE 57121Title : Paper. Determination of wax contentScope : This standard establishes the method to quantify the amount of petroleum wax in waxed
paper or so-called impregnated with paraffin, updating the analytical methodology described.
Relatedness :National : REV/AMD UNE 57121:1983
** End of Subsector **
Subsector N03: PETROLEUM PRODUCTS
Subsector : N03 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233635/0001 Project EstablishedICS :National Ref : 06233635Title : Testing of lubricants - Determination of boron content - Part 2: Direct determination by
optical emission spectral analysis with inductively coupled plasma (ICP OES)
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233636/0001 Project EstablishedICS :National Ref : 06233636Title : Lubricants - VB and VC lubricating oils with and without additives and VDL lubricating
oils - classification and requirements
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233638/0001 Project EstablishedICS :National Ref : 06233638Title : Petroleum waxes - determination of oil content
Relatedness :National : New
Page 54
Subsector : N03 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06233639/0001 Project EstablishedICS :National Ref : 06233639Title : Petroleum waxes - determination of melting point (cooling curve)
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst01394/0001 Project EstablishedICS : 75.160.30National Ref :Title : Determination of total sulfur in LP-GasesScope : This method covers the determination of total sulfur in liquified petroleum gases
containing more than 1 µg/g.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst02179/0002 Project EstablishedICS : 75.160.30National Ref :Title : Handling for liquefied petroleum gases (LPG)Scope : This specification covers the handling rules of liguefied petroleum gases (LPG) to be
followed by the consumers.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst02263/0002 Project EstablishedICS : 75.100National Ref :Title : Lubricating grease oil seperation during storageScope : This method covers the determination of the tendency of lubricating grease to seperate oil
during storage in both normally filled and partially filled containers.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02
Page 55
Organization : TSECountry : TurkeyProject ID : tst05445/0002 Project EstablishedICS : 75.080National Ref :Title : Method for Calculation of Heat Capacity of Liquid Petroleum Distillate FuelsScope : This test mrethod covers the calculation of liquid heat heat capacity, at atmospheric
pressure, of petroleum fuels for which distillation data may be obtained in accordance with Test Method D 86 without reaching a decomposition point prior to obtaining 90 volume % distilled.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst05767/0002 Project EstablishedICS : 71.100.20National Ref :Title : Estimation of Solubility of Gases in Petroleum LiquidsScope : This test method covers the estimation of the equilibrium solubility of several common
gases encountered in the aerospace industry in hydrocarbon liquids.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst13369/0001 Project EstablishedICS : 75.100National Ref :Title : Lubricating oils, industrial oils and related products - Lubricating oils (Class L) -
Naphthenic and paraffinic base oilsScope : This standard covers paraffinic and naphtenic base oils.
Relatedness :National : New
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst37416/0001 Project EstablishedICS : 75.100National Ref :Title : Lubricating oils,industrial oils and realted products-Lubricating oils(Class L)-For Smooth
bearingsScope : This standard covers lubricating oils for smooth bearings.
Relatedness :National : New
Page 56
Subsector : N03 Registration Date : 2011-02-02Organization : TSECountry : TurkeyProject ID : tst70604/0001 Project EstablishedICS : 75.100National Ref :Title : Residual fuels-Determination of phosphorous-Ultraviolet spectrometry method Scope : This standard specifies a test method for the determination of phosphorus in residual fuels
by UV sepctrometry
Relatedness :National : New
** End of Subsector **
Subsector N09: PLASTICS
Subsector : N09 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100243/0001 Project EstablishedICS :National Ref : BS 3379:2005+A1Title : Combustion modified flexible polyurethane cellular materials for loadbearing
applications. Specification. Amendment
Relatedness :National : New
Subsector : N09 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037283/0001 Project EstablishedICS :National Ref : PNE 53939Title : Plastics. Flexible polyurethane (PUR) foams for mattresses. Toxicological criteriaScope : This standard specifies toxicological criteria for flexible PUR foams for mattresses
Relatedness :National : New
** End of Subsector **
Subsector N13: LEATHER
Subsector : N13 Registration Date : 2011-02-22Organization : UNICountry : ItalyProject ID : 88000570/0001 Project EstablishedICS : 59.140National Ref : U88000570Title : Leather - Requirements for the use of the term EcoleatherScope : This standard defines the term Ecoleather and provides the rules for its use. For this scope,
it specifies product and environmental minimum requirements of the manufacturing process.
Page 57
Relatedness :National : New
** End of Subsector **
Subsector N14: PLASTICS PIPES
Subsector : N14 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023763/0001 Project EstablishedICS : 23.040.20, 23.040.45, 93.030National Ref : ONR 20513Title : Multilayer piping systems (PP-ML) for non-pressure underground drainage and
sewerage of reinforced polypropylene-compound/-blend - Dimensions, requirements tests, proof of conformity
Scope : This ONR lays down terms and definitions, nominal sizes, dimensions, requirements, tests and the quality control for solid-wall multilayer pipes (PP-ML) of reinforced polypropylene-compound or polypropylene-blends for buried gravity drainage and sewerage pipelines. Furthermore this ONR lays down terms and definitions, nominal sizes, dimensions, requirements, tests and the quality control for fittings of one polypropylene compound or of reinforced polypropylene-compounds or of polypropylene-blends for buried gravity drainage and sewerage pipelines. Pipeline systems which relate to ÖNORM EN 14758-1 or to ÖNORM EN 13476-1, -2 or -3 are not subject of this ONR. This ONR also serves as a basis for the procedure of proving the conformity of relevant products. This ONR is applicable for gravity drainage and sewerage systems used within the building structure (application area code "D") and outside the building structure (application area code "U"). The marking of both application area codes is done by means of "UD" on the pipeline components.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 58
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT
Register issued on : 2011-03-03
Page 59Subsector S01: ACOUSTICS AND SOUND INSULATION
Subsector : S01 Registration Date : 2011-02-02Organization : BSICountry : United KingdomProject ID : 01100159/0001 Project EstablishedICS :National Ref : BS 8233Title : Sound insulation and noise reduction for buildings. Code of Practice
Relatedness :National : New
** End of Subsector **
Subsector S07: ANAESTHETIC AND RESPIRATORY EQUIPMENT
Subsector : S07 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173012/0001 Project EstablishedICS :National Ref : FD S90-155Title : Pipeline for compressed medical gases and vacuum - Additional elements for design
and delivery acceptance
Relatedness :National : New
** End of Subsector **
Subsector S08: AIR QUALITY
Subsector : S08 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172431/0001 Project EstablishedICS :National Ref : PR XP X43-421Title : Stationary Source Emissions - Determination of the acid or alkaline pollution index of
gaseous
Relatedness :National : New
Subsector : S08 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172432/0001 Project EstablishedICS :National Ref : PR XP X43-420Title : Stationary source emissions - Quality Assurance of Predictive Emission Monitoring
Systems (PEMS) Stationary source emissions
Relatedness :National : New
Page 60
Subsector : S08 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173153/0001 Project EstablishedICS :National Ref : PR NF X43-244Title : Workplace atmospheres. Terminology elements in industrial hygiene. The exposure, its
assessment, the limit values
Relatedness :National : New
Subsector : S08 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173154/0001 Project EstablishedICS :National Ref : PR NF X43-299Title : Workplace air. Evaluation of the mass concentration of particles in an aerosol, using an
optical particle counter
Relatedness :National : New
** End of Subsector **
Subsector S09: WATER QUALITY AND WATER SUPPLY
Subsector : S09 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023765/0001 Project EstablishedICS : 13.060.30, 23.040.50, 93.030National Ref : ONR 22504-3Title : Internal plastics linings for concrete manhole bases - Part 3: Polyurethane (PU) linings -
Requirements, tests, quality controlScope : This ONR lays down requirements, tests and the quality control for base liners of
polyurethane (PU) serving for base units of concrete manholes. This ONR is appliccable for products to be used in manholes or inspection chambers according to ÖNORM EN 1917 and ÖNORM B 5072 for gravity sewerage and drainage conduits. In-situ installed products or products which serve for the renovation of manholes are not subject of this ONR. This ONR serves as the basis for the proof of conformity of relevant products. Furthermore, in this ONR reference is made to test methods which have to used additionally to the provisions of this ONR.
Relatedness :National : New
Subsector : S09 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023766/0001 Project Established
Page 61
ICS : 13.060.30, 23.040.50, 93.030National Ref : ONR 22504-4Title : Internal plastics linings for concrete manhole bases - Part 4: Polyethylene (PE) linings -
Requirements, tests, quality controlScope : This ONR lays down requirements, tests and the quality control for base liners of
polyethylene (PE) serving for concrete manhole base units. This ONR is appliccable for products to be used in manholes or inspection chambers according to ÖNORM EN 1917 and ÖNORM B 5072 for gravity sewerage and drainage systems. In-situ installed products or products which serve for the renovation of manholes are not subject of this ONR. This ONR serves as the basis for the procedure for the proof of conformity of the relevant products. Furthermore, in this ONR reference is made to standards concerning test methods which have to used in addition to the provisions of this ONR.
Relatedness :National : New
** End of Subsector **
Subsector S18: STERILIZATION OF EQUIPMENT
Subsector : S18 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06301447/0001 Project EstablishedICS :National Ref : 06301447Title : Sterilization - packing materials for sterilizing goods, sterilizing baskets made of metal
Relatedness :National : New
Subsector : S18 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 06301448/0001 Project EstablishedICS :National Ref : 06301448Title : Sterilization - packing materials for sterilizing goods, instrument trays made of metal
Relatedness :National : New
** End of Subsector **
Subsector S26: ENVIRONMENTAL MANAGEMENT
Subsector : S26 Registration Date : 2011-02-08Organization : NENCountry : NetherlandsProject ID : 50001618/0001 Project EstablishedICS :National Ref : NEN 5639:2010 Concept nlTitle : Radioactivity measurements - Determination of the ambient dose equivalent rate due to
photon radiation by portable monitorsScope : This standard describes the method for the determination of the ambient dose equivalent
Page 62
Scope : rate with portable monitors. This makes monitoring on site possible. These measurements supports control of statutory limits.
Relatedness :National : New
** End of Subsector **
Subsector S27: WASTE - CHARACTERIZATION, TREATMENT AND STREAMS
Subsector : S27 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA168317/0001 Project EstablishedICS :National Ref : PR XP T97-001-2Title : Tests on sludges - Part 2 : sedimentation speed and gravity thickening capability
Relatedness :National : REV/AMD T97-001:197911 (T97-001)
** End of Subsector **
Subsector S99: UNDETERMINED
Subsector : S99 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023759/0001 Project EstablishedICS : 01.040.11, 11.180.10National Ref : ÖNORM K 1101Title : Wheelchairs - Terms and definitions and explanations (bilingual edition)Scope : This ÖNORM includes a consistently list of the most common terms used form different
interest groups in connection with wheelchairs, the definitons, important explanations and additional informations.
Relatedness :National : New
Subsector : S99 Registration Date : 2011-02-14Organization : ASICountry : AustriaProject ID : 00023760/0001 Project EstablishedICS : 11.180.30National Ref : ÖNORM V 2105Title : Technical aids for visually impaired and blind persons - Tactile inscriptions and
information systems Scope : This ÖNORM regulates tangible inscription and information systems on and in public parks,
public service vehicles, public buildings as well as public recreational facilities e.g. in the form of building situation plans, information points and hand course inscription.
Relatedness :National : New
Page 63
Subsector : S99 Registration Date : 2011-02-25Organization : SNV Draft Issue Date : 2011-02-24Country : Switzerland Latest Date for Comments : 2011-06-01Project ID : CH110005/0001 Draft for public enquiryICS : 11.020National Ref : prSN 22500Title : Structural requirements for surgery departments in consideration of the Good Operating
Practice
Relatedness :National : New
Subsector : S99 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173158/0001 Project EstablishedICS :National Ref : PR NF S97-115Title : Medical light support and compression textile bandages . Technical specifications
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 64
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING
Register issued on : 2011-03-03
Page 65Subsector T01: SHIPBUILDING AND MARITIME STRUCTURES
Subsector : T01 Registration Date : 2011-02-11Organization : DINCountry : GermanyProject ID : 13202311/0001 Project EstablishedICS :National Ref : 13202311Title : Rim-locks without latch-bolt for heavy hinged doors
Relatedness :National : New
** End of Subsector **
Subsector T02: AEROSPACE
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172911/0001 Project EstablishedICS :National Ref : PR NF L17-120Title : Aerospace series - Butadiene - Acrylonitrile rubbers - Class 20 - Characteritics
Relatedness :National : REV/AMD NF L17-120:198506 (L17-120)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172912/0001 Project EstablishedICS :National Ref : PR NF L17-121Title : Aerospace series - Butadiene - Acrylonitrile rubbers - Class 21 - Characteritics
Relatedness :National : REV/AMD NF L17-121:198506 (L17-121)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172913/0001 Project EstablishedICS :National Ref : PR NF L17-123Title : Aerospace series - Butadiene - Acrylonitrile rubbers - Class 23 - Characteritics
Relatedness :National : REV/AMD NF L17-123:198506 (L17-123)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : France
Page 66
Project ID : FA172914/0001 Project EstablishedICS :National Ref : PR NF L17-124Title : Aerospace series - Butadiene - Acrylonitrile rubbers - Class 24 - Characteritics
Relatedness :National : REV/AMD NF L17-124:198506 (L17-124)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172915/0001 Project EstablishedICS :National Ref : PR NF L17-126Title : Aerospace series - Rubber - Butadiene -Acrylonitrile, hydrogenated - Class 26 -
Characteristics
Relatedness :National : REV/AMD NF L17-126:199903 (L17-126)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172916/0001 Project EstablishedICS :National Ref : PR NF L17-131Title : Aerospace serie - Polychloroprène rubbers - Class 31 - Characteristics
Relatedness :National : REV/AMD NF L17-131:198506 (L17-131)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172917/0001 Project EstablishedICS :National Ref : PR NF L17-132Title : Aerospace series - Polychloroprene rubbers - Class 32 - Characteristics
Relatedness :National : REV/AMD NF L17-132:198506 (L17-132)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172918/0001 Project EstablishedICS :National Ref : PR NF L17-151Title : Aerospace series - Silicone rubbers - Class 51 - Characteristics
Relatedness :National : REV/AMD NF L17-151:198506 (L17-151)
Page 67
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172919/0001 Project EstablishedICS :National Ref : PR NF L17-153Title : Aerospace series - Silicone rubbers - Class 53 - Characteristics
Relatedness :National : REV/AMD NF L17-153:198506 (L17-153)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172920/0001 Project EstablishedICS :National Ref : PR NF L17-162Title : Aerospace industry - Halogeno carbon rubbers - Class 62 - Characteristics
Relatedness :National : REV/AMD NF L17-162:198811 (L17-162)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172921/0001 Project EstablishedICS :National Ref : PR NF L17-163Title : Aerospace industry - Fluoro silicone rubbers - Class 63 - Characteristics
Relatedness :National : REV/AMD NF L17-163:198811 (L17-163)
Subsector : T02 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA172922/0001 Project EstablishedICS :National Ref : PR NF L17-164Title : Aerospace industry - Fluorocarbon rubbers - Class 64 - Characteristics
Relatedness :National : REV/AMD NF L17-164:198708 (L17-164)
** End of Subsector **
Subsector T19: ROAD SAFETY
Subsector : T19 Registration Date : 2011-02-28Organization : AENOR
Page 68
Country : SpainProject ID : P0037268/0001 Project EstablishedICS :National Ref : PNE 199141-1Title : Road traffic management equipment. Artificial vision. License plate readers. Part 1:
Functional specificationsScope : This standard defines the functional specifications for the license plate readers.
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037269/0001 Project EstablishedICS :National Ref : PNE 199141-2Title : Road traffic management equipment. Artificial vision. License plate readers. Part 2:
Applying protocolsScope : This standard defines the protocols to be applied to for the license plate readers
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037270/0001 Project EstablishedICS :National Ref : PNE 199141-3Title : Road traffic management equipment. Artificial vision. License plate readers. Part 3:
EquipmentScope : This standard defines the equipment for the license plate readers
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037271/0001 Project EstablishedICS :National Ref : PNE 199141-4Title : Road traffic management equipment. Artificial vision. License plate readers. Part 4:
Conservation and maintenanceScope : This standard defines the conservation and maintenance protocols to be applied to for the
license plate readers
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28
Page 69
Organization : AENORCountry : SpainProject ID : P0037272/0001 Project EstablishedICS :National Ref : PNE 199142-1Title : Road traffic management equipment. Artificial vision. Offending vehicles detection. Part
1: Functional requirements and application protocol for red light traffic signalsScope : This standard comprises both functional specifications and communications protocol for
equipments addressed to red light semaphores offending vehicles detection.
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037273/0001 Project EstablishedICS :National Ref : PNE 199143-1Title : Road traffic management equipment. Artificial vision. Equipment for offending vehicles
detection. Part 1: Red light traffic signals systemsScope : This standard defines the equipment for red light semaphores offending vehicles detection
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037274/0001 Project EstablishedICS :National Ref : PNE 199121-2Title : Road Traffic Management Equipment. Stationary kinemometers. Part 2: Pole universal
cabinets for fixed installations.Scope : This standard defines environmental, electrical and constructing technical characteristics of
pole universal cabinets for laser or radar kinemometers.
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037275/0001 Project EstablishedICS :National Ref : PNE 199121-3Title : Road Traffic Management Equipment. Stationary kinemometers. Part 4: Frame
universal cabinets for fixed installations.Scope : This standard defines environmental, electrical and constructing technical characteristics of
universal cabinets for laser or radar kinemometers installed on a frame
Relatedness :National : New
Page 70
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037276/0001 Project EstablishedICS :National Ref : PNE 199123-1Title : Road Traffic Management Equipment. Kinemometers. Cabinets for external flash. Part
1: Installation on the edge of the road.Scope : This standard defines the requirements for the cabinets for external flash to be installed on
the edge of a road, for use with kinemometers
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037277/0001 Project EstablishedICS :National Ref : PNE 199123-2Title : Road Traffic Management Equipment. Kinemometers. Cabinets for external flash. Part
2: Installation on a poleScope : This standard defines the requirements for the cabinets for external flash to be installed on
pole, for use with kinemometers
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037278/0001 Project EstablishedICS :National Ref : PNE 199124-4Title : Road Traffic Management Equipment. Kinemometers average speed in section. Part 4:
Functional specifications and applying protocolsScope : This standard defines both functional specifications and communications protocol for
kinemometers measuring the average speed in a defined length of a road.
Relatedness :National : New
Subsector : T19 Registration Date : 2011-02-28Organization : AENORCountry : SpainProject ID : P0037285/0001 Project EstablishedICS :National Ref : PNE 199151-1Title : Road equipment. Data quality. Exchange of information between control centres. Part 1:
functional specification.Scope : This standard defines a system for the exchange of information between Traffic Control
Centres of an area or region (Zonal Traffic Control Centre) and other systems or Institutions.
Page 71
Scope : The goal is to have a standard platform delivering the real-time publication of traffic, meteorological and signalling parameters, enabling several systems to exchange information and consult historical and statistical information.
Relatedness :National : New
** End of Subsector **
** End of Sector **
Information procedure Page 72
Monthly Notifications Register
Notifications registered at CCMC from 2011-02-01 to 2011-02-28
Sector X : UNDETERMINED STANDARDIZATION AREA
Register issued on : 2011-03-03
Page 73Subsector X01: UNDETERMINED STANDARDIZATION AREA (NON-ELECTRICAL)
Subsector : X01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173168/0001 Project EstablishedICS :National Ref : PR NF X50-769Title : Training services - Value chain of a training action
Relatedness :National : New
Subsector : X01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173169/0001 Project EstablishedICS :National Ref : PR NF X50-768Title : Training services - Training assessment
Relatedness :National : New
Subsector : X01 Registration Date : 2011-02-25Organization : AFNORCountry : FranceProject ID : FA173170/0001 Project EstablishedICS :National Ref : PR NF X50-766Title : Training services - Lisibility of the training offer
Relatedness :National : New
** End of Subsector **
** End of Sector **
2010-12
List of non-electrotechnical subsectors
Sector A: Services
Subsector Title ISO/TC CEN/TC
reference reference
A01 Tourist services / 329; CEN/WS ETO
A02 Cleaning services / 328
A03 Postal services / 331
A04 Transportation services / 320; CEN/WS 016; CEN/WS SCUTUM
A05 Maintenance services / 319
A06 Building and construction services / 330
A07 Translation services /
A08 Funeral services / CEN/BT/TF 139
A09 Facility management / 348
A10 Services of Real Estate Agents / CEN/BT/TF 180; 373
A11 Security Services / CEN/BT/TF 167; 391; 384; 370; CEN/WS 044; CEN/CLC/TC 4
A12 Consultancy Services / 395; 381
A13 Expertise Services / 405
A99 Undetermined / CEN/WS 002; CEN/WS 004; CEN/WS 037; CEN/WS 039; CEN/WS 041; CEN/WS 051; 375; 374; 376; 385; 404
Sector B: Building and construction
Subsector Title ISO/TC CEN/TC
reference reference
B01 Fire protection 21 70; 72; 191; 192
B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340
B03 Concrete 71 104; CEN/WS 009
B04 Cement 74; 77 51
B05 Fire tests 92 127
B06 Gypsum / 241
B07 Glass 160 129
B08 Doors and windows 162 33
B09 Thermal matters 163 88; 89; 371; CEN/BT WG 173; CEN/WS 036
B10 Timber structures 165 124
B11 Metal structures 167 135
B12 Masonry 179; 196 125; 246
B13 Solar energy 180 312
B14 Geotechnics 182 341; 396
B15 Sanitary appliances / 163; 7
B16 Taps / /
B17 Lighting equipment and lighting / 50; 169 application technology
B18 Scaffolding / 53
B19 Ceramic tiles 189 67
B20 Drainage equipment / 165
B21 Baths / /
B22 Wallcoverings / 99
B23 District heating / 107
B24 Auxiliary and handicraft work / /
B25 Gas distribution installation and / 234; 235; 282 related equipment
B26 Road building and maintenance / 178; 227
B27 Waterproofing materials / 128; 254; 361; 314
B28 Floor coverings 38/SC 12 134
B29 Aggregates / 154
B30 Floor and surfacing / 217; 303; 323; 390
B31 Heating systems in buildings / 228; 247
B32 Precast concrete products / 177; 229
B33 Building design 205 315; 325; 388
B34 Building and construction – Environmental aspect 350; 351
B99 Undetermined / /
Sector C: Chemicals, chemical engineering and food products
Subsector Title ISO/TC CEN/TC
reference reference
C01 Food products 34 174; 275; 302; 360; 307; 327; 338; 387; CEN/WS 008; CEN/WS 018; CEN/WS 054
C02 Paints and related products 35 139; 298; 173
C03 Chemistry 47 317; 363
C04 Laboratory glassware 48 332
C05 Lac / /
C06 Essential oils 54 /
C08 Pesticides 81 /
C09 Surfactants 91 276
C10 Starch 93 /
C11 Tobacco 126 401
C12 Glass plant / /
C13 Fertilizers 134 223; 260
C16 Wood preservatives / /
C17 Trees and plants / /
C18 Adhesives / 193
C19 Chemical analysis 201; 202 382; 347
C20 Explosives and firework / 212; 321
C21 Cosmetics 217 392
C99 Undetermined / 386
Sector F: Fundamental standards
Subsector Title ISO/TC CEN/TC
reference reference
F01 Technical drawings 10 /
F02 Units & symbols 12 /
F03 Preferred numbers 19 /
F04 Sieves 24 /
F05 Measuring instruments 30; 113 92; 171; 176; 237;
294; 318; 244; 367; 141; CEN/WS 011
F06 Terminology principles 37 /
F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368
F08 Surfaces / 290
F09 Banking 68 /
F10 Statistics 69 /
F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365
F13 Environmental tests / /
F14 Graphical technology, 130 / sign-boards and nameplates
F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033
F16 Graphical symbols 145 /
F17 Administrative documents 154 CEN/WS MMU
F18 Micrographics 171 /
F19 Optics 172; 187 123; 170
F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362
F21 Value analysis and project / 279 network
F22 Logistics / 379; 273
F23 Energy 203 CEN/CLC/JWG 1; CEN/CLC/JWG 2;
CEN/CLC/JWG 3; CEN/CLC/JWG 4; CEN/WS 027
F99 Undetermined / 389; CEN/WS 057; CEN/WS 058; CEN/WS 060
Sector H: Products for household and leisure use
Subsector Title ISO/TC CEN/TC
reference reference
H01 Cinematography 36 372
H02 Photography 42 /
H03 Consumer questions / 291
H04 Sports equipment 83 136
H05 Oil and gas burners / 47; 131
H06 Horology 114 /
H07 Space heating 116 62; 110; 130; 179; 180
H08 Sizing systems 133; 137 /
H09 Furniture 136 207
H10 Sewing machines 148 /
H11 Heater controls 161 58
H12 Ceramic and glass-ware for food 166 /
H13 Jewellery 174 CEN/WS 047
H14 Caravans 177 245
H15 Toys 181 52
H17 Oil stoves / 46
H18 Central heating boilers / 48; 57; 109; 269
H19 Non-electric cookers and barbecues / 49; 281; 295
H22 Smokers’ lighters and matches / 355; 87
H23 Ladders / 93
H24 Tactile danger warnings / /
H25 Large gas appliances / 106; CEN/CLC/JWG FCGA
H26 Sealing materials / 108; 208
H27 Educational equipment / /
H28 Hunting 191 /
H29 Heat pumps / 113
H30 Equipment for children / 252
H31 Dedicated LPG appliances / 181
H32 Culinary utensils 186 194
H33 Footwear (excluding protective / 309 footwear)
H34 Child safety / CEN/BT/WG 117 398
H99 Undetermined / 299; 364; 369; 402
Sector I: Mechanical engineering
Subsector Title ISO/TC CEN/TC
reference reference
I01 Screw threads 1 /
I02 Fasteners 2 185
I03 Limits & fits / /
I04 Rolling bearings 4 /
I05 Iron pipes 5 203
I06 Pressure vessels 11 54
I07 Shafts 14 /
I08 Agricultural machines 23 144, 334
I09 Small tools 29 213
I10 Splines / /
I11 Machine tools 39 142; 143; 145; 255
I12 Pulleys & belts 41 188
I13 Gas containers 58 23; 286
I14 Gears 60 /
I15 Equipment for petroleum industry 67 12
I16 Internal combustion engines 70; 192 270
I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025
I18 Mining 82 196
I19 Nuclear energy 85 /
I20 Refrigeration 86 44; 182
I21 Chains and chain wheels 100 /
I22 Vacuum technology 112 /
I23 Pumps 115 197
I24 Industrial fans 117 356
I25 Compressors 118 232
I26 Plain bearings 123 /
I27 Earth moving and construction 127; 195 151 equipment
I28 Fluid power 131 /
I29 Gas cleaning / 195
I30 Air distribution / 156
I31 Valves 153; 185 69; 236; 105
I32 Flanges / 74
I33 Information processing in 184 310 automation
I34 Non-ferrous metallic pipes / /
I35 Leisure and recreational machines / 152
I36 Thermoprocessing technology / 186
I37 Printing and paper machines / 198
I38 Leather production, tannery and / 200; 201 related machinery
I39 Machines for metal processing / 202; 322
I40 Industrial piping networks / 267
I41 Membrane filters / 272
I42 Potentially explosive atmospheres / 305
I43 Hydrogen energy 197 /
I44 Nanotechnologies 229 352
I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2; 65, 157; CEN/WS 059
Sector M: Metallic materials
Subsector Title ISO/TC CEN/TC
reference reference
M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110
M02 Zinc / 209
M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron
M04 Copper 26 133
M05 Welding 44 121
M06 Dimensions of wrought products / /
M07 Manganese and chromium 65 /
M08 Light alloys 79 132
M09 Iron ores 102 /
M10 Metallic coatings 107 240
M11 Powder metallurgy 119 /
M12 Aluminium ores 129 /
M13 Ferroalloys 132 /
M14 Nickel 155 /
M15 Metallic corrosion 156 262; 219
M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101
M17 Heavy metal ores 183 /
M18 Metal wire products / ECISS/TC 30; CEN/BT/TF 196; 378
M20 Tin and tin alloys / 220
M21 Precious metals / 283
M22 Lead and lead alloys / 306
M99 Undetermined / /
Sector N: Non-metallic materials
Subsector Title ISO/TC CEN/TC
reference reference
N01 Paper and board 6 172
N02 Solid fuels 27 335; 343;383; CEN/WS 019
N03 Petroleum products 28 19; 336; CEN/WS 038; CEN/WS 061
N04 Refractories 33 187
N05 Textiles 38 189; 248
N06 Rubber 45 218; 366 CEN/WS 003
N07 Sawn timber 55 38; 175
N08 Mica / /
N09 Plastics 61 249
N10 Cork 87 /
N11 Wood-based panels 89 112
N12 Timber products 99 /
N13 Leather 120 289
N14 Plastics pipes 138 155
N17 Fluorspar 175 /
N18 Glass-fibre reinforced plastics / /
N19 Tapes / 253
N20 Ceramics 206 184
N21 Gaseous fuels and combustible gas 158; 193 238
N22 Feather and related materials / 222
N99 Undetermined / /
Sector S: Health, environment and medical equipment
Subsector Title ISO/TC CEN/TC
reference reference
S01 Acoustics and sound 43 126; 211 insulation
S02 Transfusion equipment 76 /
S03 Syringes 84 /
S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162; CEN/WS 026; CEN/WS 043
S05 Dentistry 106 55
S06 Vibration & shock 108 231
S07 Anaesthetic and respiratory 121 215 equipment
S08 Air quality 146 137; 243; 264; CEN/CLC/JWG CMI
S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034
S10 Surgical implants 150 285; CEN/CLC/JWG AIMD
S11 Contraceptives 157 /
S12 Gas analysis / /
S13 Ergonomics 159 122
S14 Prosthetics 168 /
S15 Surgical instruments 170 /
S16 Aids for the disabled 173 293
S17 Respiratory protective devices / 79
S18 Sterilization of equipment 198 102; 204
S19 First aid equipment and rescue systems / 239
S20 Waste collection, handling and / 183 transportation
S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316; CEN/CLC/TC 3; CEN/WS 031; CEN/WS 053; CEN/WS 055
S22 Energy saving / CEN/WS 005 CEN/WS 015
S23 Personal & property protection against aggression/Burglary protection / 263
S24 Soil quality 190 345; CEN/WS 032
S25 Chemical disinfectants and / 216 antiseptics
S26 Environmental management 207 CEN/TC 406; CEN/WS 040
S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120
S28 Demining / CEN/WS 029 CEN/WS 013
S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; 403 CEN/WS PCEC CEN/WS 012 CEN/WS 020
Sector T: Transport, mechanical handling and packaging
Subsector Title ISO/TC CEN/TC
reference reference
T01 Shipbuilding and maritime 8; 188 15; 300 structures
T02 Aerospace 20 274; AECMA; ECSS ;377
T03 Road vehicles 22 301; 326 CEN/WS IMA
T04 Tyres 31 /
T05 Pallets 51 /
T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393
T07 Glass containers 63 /
T08 Cranes 96 147
T09 Materials handling and 101 148; 149 storage equipment
T10 Freight containers 104 119; 280
T11 Steel wire ropes 105 /
T12 Industrial trucks 110 150; 324
T13 Lifting chains, hooks and ropes 111 168
T14 Packaging 122 261; 120
T15 Cycles 149 333
T16 Lifts & escalators 178 10; 242
T17 Builders hoists / /
T18 Elevating platforms / 98
T19 Road safety / 226; 339
T20 Tram- and railway engineering / 256; / CEN/CLC/WG FPR
T21 Packaging machines / 146
T22 Off-road vehicles / 354
T99 Undetermined / CEN/WS TAF
Sector Z: Information technology
Subsector Title ISO/TC CEN/TC
Z01 Radiocommunication for IT / /
Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI
Z03 Common O.S.I. activities / CEN/CLC - EWOS
Z99 Undetermined / 353; CEN/WS ADN; CEN/WS AUT; CEN/WS BII; CEN/WS CAT; CEN/WS CST; CEN/WS CTC; CEN/WS DFA; CEN/WS DIR; CEN/WS DIS; CEN/WS DPA; CEN/WS DPP; CEN/WS EBE; CEN/WS ECH; CEN/WS ECO; CEN/WS EFI; CEN/WS EMD; CEN/WS ESI; CEN/WS ESR; CEN/WS EUR; CEN/WS FAS; CEN/WS FIN; CEN/WS FS2; CEN/WS FUN; CEN/WS GEN; CEN/WS HIC; CEN/WS ICT; CEN/WS IEC; CEN/WS IHM; CEN/WS INV2; CEN/WS ISD; CEN/WS JXF; CEN/WS KMA; CEN/WS LCT; CEN/WS LTS; CEN/WS MDC; CEN/WS MEE; CEN/WS MES; CEN/WS MET; CEN/WS MLX; CEN/WS MMI; CEN/WS NEA; CEN/WS NOM; CEN/WS ORC; CEN/WS POR; CEN/WS QIS; CEN/WS SAN; CEN/WS SCE; CEN/WS TEX; CEN/WS TWE; CEN/WS UDP; CEN/WS URI; CEN/WS WAC;
CEN/WS XFS; CEN/WS XML; CEN/WS eGo; CEN/WS eIN; CEN/WS ePR