MODEL AR-5015 N AR-5120 - sharp.eu€¦ · •getting started • making copies • status indicators • general information • optional equipment 2 13 28 36 55 digital laser copier

• GETTING STARTED

• MAKING COPIES

• STATUS INDICATORS

• GENERAL INFORMATION

• OPTIONAL EQUIPMENT

2

13

28

36

55

DIGITAL LASER COPIER

OPERATION MANUAL

Page

MODEL

AR-5015 NAR-5120

AR-5120

AR-5015 N

CAUTIONSFollow the cautions below when using this copier.

� The fusing area is hot. Exercise care in this area when removing misfed paper.� Do not look directly at the light source. Doing so may damage your eyes.

� Place the copier on a firm, level surface.� Do not install the copier in a humid or dusty location.� When the copier is not used for a long time, for example, during prolonged holidays, turn the power

switch off and remove the power cord from the outlet.� When moving the copier, be sure to turn the power switch off and remove the power cord from the

outlet.� Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may

prevent heat dissipation, damaging the copier.� Use of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous laser radiation exposure.

Cautions on laser

Wave length 785 nm ±10 nm

Pulse times (8.141 µs ±0.1 µs)/7 mm

Output power 0.22 mW ±0.01 mW

1

GE

TT

ING

STA

RT

ED

STA

TU

SIN

DIC

ATO

RS

MA

KIN

G C

OP

IES

GE

NE

RA

L IN

FO

RM

AT

ION

OP

TIO

NA

LE

QU

IPM

EN

T

CONTENTS Page

GETTING STARTED� INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2� MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3� PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . 4

– Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4– Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

� COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 8� CAUTIONS ON HANDLING . . . . . . . . . . . . . . . . . . . . . . . . 9� LOADING COPY PAPER . . . . . . . . . . . . . . . . . . . . . . 10

MAKING COPIES� AUDITING ACCOUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . 13� NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14� REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . 16� BYPASS FEED (special paper) . . . . . . . . . . . . . . . . . . . 18� TWO-SIDED COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . 20� XY ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21� B/W REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23� DUAL PAGE COPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24� INTERRUPTING A COPY RUN . . . . . . . . . . . . . . . . . . . . 25� AUTOMATIC EXPOSURE ADJUSTMENT . . . . . . . . . . . 26� TONER SAVE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

STATUS INDICATORS� TONER CARTRIDGE REPLACEMENT . . . . . . . . . . 28� MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . 30� DEVELOPER REQUIRED . . . . . . . . . . . . . . . . . . . . . 35� MAINTENANCE REQUIRED . . . . . . . . . . . . . . . . . . . 35

GENERAL INFORMATION� USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

– Settings for auditing accounts . . . . . . . . . . . . . . . . . . . . . . 39� POWER SAVE MODES . . . . . . . . . . . . . . . . . . . . . . . . . . 43� USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 45� COPIER TROUBLE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47� SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

– Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . 50– Genuine supplies statement . . . . . . . . . . . . . . . . . . . . . . . . 51

� SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

OPTIONAL EQUIPMENT� SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . 56

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2

GE

TT

ING

STA

RT

ED

INTRODUCTIONThis copier has been designed to provide convenient copying features in a minimumamount of office space and with maximum operational ease. To get full use of all copierfeatures, be sure to familiarise yourself with this manual and the copier.For quick reference during copier use, keep this manual in a handy location.

Introduction

Conventions used in this manual

In this manual, the following icons are used to provide the user withinformation pertinent to the use of the copier.

Warns the user that injury to the user or damage to thecopier may result if the contents of the warning are notproperly followed.

Cautions the user that damage to the copier or one of itscomponents may result if the contents of the caution arenot properly followed.

Notes provide information relevant to the copier regardingspecifications, functions, performance, operation and such,that may be useful to the user.

Indicates a letter displayed in the copy quantity display.

Some models may not be available in some countries.

AR-5120 is equipped with two paper trays while AR-5015 Nis equipped with one paper tray. The illustrations in thismanual are mainly for AR-5015 N.

3

GE

TT

ING

STA

RT

ED

MAIN FEATURESHigh-speed laser copying� First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on).

� Copying speed is 15 copies/min. (AR-5015 N) or 20 copies/min. (AR-5120), which adapts to business use, allowingimprovement of working efficiency.

High-quality digital image� High-quality copying at 600 dpi is performed.

� In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.

� The photo mode copying function allows clear copying of delicate halftone original images such as monochromephotos and colour photos. Photo mode is adjustable in five steps.

Substantial copying features� Zoom copying from 50% to 200% in 1% increments can be performed.

� Continuous copying of maximum 99 sheets can also be performed.

� Useful special features such as the XY zoom, black and white reverse, and dual page copy are available.

� User programs allow setting/modification of functions for customer needs. Also the user programs allow the internalauditor to be controlled.

Optional feature� An optional single pass feeder (SPF) allows automatic document feeding of up to 30 sheets.

Scan once/ Print many (AR-5120 only)� The copier is equipped with a 1-page memory buffer. This memory allows the copier to scan an original 1 time only

and make up to 99 copies. This feature allows for improved workflow, reduced operating noise from the copier andreduced wear and tear on the scanning mechanism, which provides for a higher reliability.

Environmentally friendly design� Paper output tray is housed in the copier for space saving.

� Preheat and auto power shut-off modes are provided to reduce power consumption in standby mode.

Main features

4

GE

TT

ING

STA

RT

ED

PART NAMES AND FUNCTIONS

Overall layout

Platen coverPlace the original on the original table and close theplaten cover before copying starts.

Original tablePlace the document to be copied here.

HandlesUse to move the copier.

Power switchPress to turn copier power on and off.

Operation panelAll copier controls are located here for easy operation.

Paper output trayFinished copies are deposited in the paper output tray.

Front coverOpen to remove misfeeds and for copier servicing.

Paper trayHolds 250 sheets of copy paper.(AR-5120 is equipped with two paper trays.)

Side coverOpen to remove misfeeds and to service the copier.

Side cover handleLift and pull to open the side cover.

Bypass tray guidesAdjust to the width of the copy paper.

Bypass trayPaper including special paper (such as transparencyfilm) can be fed from the bypass tray.

Bypass tray extensionPull out when feeding large paper such as B4 and A3.

Charger cleanerUse to clean the transfer charger.

GE

TT

ING

STA

RT

ED

Part names and functions

5

GE

TT

ING

STA

RT

ED


Toner cartridge lock release leverUse to unlock the toner cartridge.

Toner cartridgeContains toner.

Photoconductive drumCopy images are formed on the photoconductive drum.

Roller rotating knobTurn to remove misfed paper.

Fusing unit release leversLower to remove misfed paper.

The fusing unit is hot.

Take care in removing paper.

Paper guideOpen to remove misfed paper.

Accessories

Operation manual . . . . . . . . . . . . . . . . . . . . . . 1Charger cleaner . . . . . . . . . . . . . . . . . . . . . . . . 1


GE

TT

ING

STA

RT

ED

6

GE

TT

ING

STA

RT

ED

Operationpanel


INTERRUPT ( ) key and indicator (p. 25)Interrupts a copy run.

Copy quantity displayDisplays the specified copy quantity during the readycondition and displays the copy countdown as copiesare made. Also see items and .

ZOOM indicator (p. 17)Lights up when a zoom ratio is set.

Copy ratio display ( ) key (p. 17)Press and hold down during standby to display the copyratio in the copy quantity display.

Zoom keys (p. 17)Use to select any reduction or enlargement copy ratiofrom 50% to 200% in 1% increments.

PAPER SIZE ENTER ( ) key (p. 12)Use to set the paper size in a paper tray.

AUDIT CLEAR ( ) key (p. 13)Closes an open account.

PAPER SIZE indicatorsLight up to show the selected copy paper size.

Alarm indicators: Maintenance indicator (p.35): Toner cartridge replacement required indicator

(p.28): Developer replacement required indicator (p.35): Paper required indicator (p.10): Misfeed indicator (p.30)

POWER SAVE ( ) indicator (p. 43)Lights up when the copier is in a preheat mode.

SPF indicator (p. 57)Lights up when originals are set in the optional SPF.

Output tray full indicatorIndicates copies must be removed from the paper outputtray.

B/W REVERSE ( ) key and indicator (p. 23)Press to reverse the black and white areas.

XY-ZOOM ( ) key and indicator (p. 21)Press to change the horizontal and vertical copy ratiosindependently.

AUTO/MANUAL/PHOTO ( / / ) key andindicators (p. 14)Use to sequentially select the exposure modes: AUTO,MANUAL, or PHOTO.

Light ( ) and dark ( ) keys and indicators(p. 15)Use to adjust the MANUAL or PHOTO exposure level.

Numeric keysUse to select the desired copy quantity or to make userprogram entries.

GE

TT

ING

STA

RT

ED


Not used

7

GE

TT

ING

STA

RT

ED


Zero keyUse as part of numeric keys to enter copy quantity.Press during a continuous copy run to display thenumber of copies completed in the current run.Press and hold during standby to display the total outputcount.

Press and hold down the key. 12,345 sheets output

1st display 2nd display

Note: A3 size copies are counted as two copies.

CLEAR ( ) keyClears the copy quantity display or terminates a copyrun.

START ( ) key and indicatorCopying is possible when the indicator is on.Press to start copying.

CLEAR ALL ( ) keyClears all selected settings and returns the copier to theinitial settings.

PRESET RATIO selector keys and indicators(p. 17)Use to sequentially select preset reduction/enlargementcopy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,141%, 200%.

ORIGINAL SIZE ENTER ( ) key andindicators (p. 16)Use to input the original size for automatic paper selection(AR-5120 only) and automatic copy ratio selection.

AUTO PAPER SELECT ( ) indicator(AR-5120 only)Paper of the proper size will be automatically selecteddepending on the original size and selected copy ratiowhen this indicator is on.

TRAY SELECT ( ) key (p. 14)Use to manually select a paper tray.

AUTO IMAGE ( ) key and indicatorPress for automatic copy ratio selection.

Paper feed location/misfeed location indicators(p. 30)The selected paper feed location is shown by a litindicator ( ).The general location of misfed paper is shown by ablinking red indicator ( ).

DUAL PAGE COPY ( ) key and indicator(p. 24)Use to make individual copies of two originals placedside by side on the original table.

Initial settingsThe copier assumes the initial settings when it is first turnedon, when the CLEAR ALL ( ) key is pressed, andapproximately one minute* after the last copy is made in anymode.� Copy ratio: 100%� Exposure: Automatic� Copy quantity: 0� All special copier modes: Off� Auto paper selection : On (AR-5120 only)� Paper feed station: Previously selected paper tray

* This time (auto clear time) can be changed. See page 36,USER PROGRAMS.


GE

TT

ING

STA

RT

ED

The illustration on the left showsthe operation panel of AR-5015 N.The portion of the operation panelof AR-5120 that is different fromAR-5015 N is shown above.

8

GE

TT

ING

STA

RT

ED

10 cm

Copier installation

COPIER INSTALLATIONImproper installation may damage the copier. Please note the followingduring initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier.Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at roomtemperature for at least 2 hours before use.

Do not install your copier in areas that are:

� damp, humid, or very dusty

� exposed to direct sunlight

� poorly ventilated

� subject to extreme temperature or humidity changes, e.g., near anair conditioner or heater.

The copier should be installed near an accessible power outletfor easy connection.

Be sure to connect the power cord only to a power outlet thatmeets the specified voltage and current requirements.Also make certain the outlet is properly grounded.� For this copier’s power supply requirements, see the name plate located

on the back of the unit.

Connect the copier to a power outlet which is not usedfor other electric appliances. If a lighting fixture isconnected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine forservicing and proper ventilation.

9

GE

TT

ING

STA

RT

ED

CAUTIONS ON HANDLINGBe careful in handling the copier as follows to maintain the performance ofthis copier.

Do not drop the copier, subject it to shock or strike it against anyobject.

Store spare toner cartridges in a cool dry place without removingfrom the package before use.If they are exposed to direct sunlight or excessive heat, poor copiesmay result.

Do not touch the photoconductive drum (green portion).Scratches or smudges on the drum will cause dirty copies.

Cautions on handling

10

GE

TT

ING

STA

RT

ED

LOADING COPY PAPERTo save space, this copier has been designed with one (AR-5015 N) or two(AR-5120) adjustable front-loading trays, which are easily opened for paperloading. For best results, use only SHARP recommended paper. (See page 50.)The paper required ( ) indicator will light up when there is no copy paper inthe selected paper feed station, or when the paper tray is not installed or isimproperly installed.

When the paper size is changed in the paper tray, the size ofthe paper must be entered by steps 8 through 11 on page12. If not, the edges of copies may become smudged withtoner. Also, the AUTO PAPER SELECT (AR-5120 only) andthe AUTO IMAGE feature will not function properly.

1 Gently lift and pull out the paper tray until it stops.

2 Push the pressure plate down until it locks in place.

3 Fan the copy paper and insert it into the tray. Make surethe edges go under the corner hooks.� If you change to a different size of copy paper, the tray must be

adjusted. See the next page.

� Set the paper along the guides.

� The tray holds up to 250 sheets of paper.Do not load paper above the maximum height line.

4 Push the paper tray firmly back into the copier.

Loading copy paper

Maximum height line

11

GE

TT

ING

STA

RT

ED

Changing the copy paper size in the tray

1 Gently lift and pull out the paper tray until it stops.

2 Push the pressure plate down until it locks in place.

3 Squeeze the lock lever of the front guide and slide thefront guide to match the width of the paper.

4 Move the left guide to the appropriate slot as markedon the tray.� A5 copy paper cannot be used in the lower paper tray of AR-5120.

5 Load copy paper into the tray.

6 Place the appropriate label to indicate the selectedpaper size into the recess on the right front side of thepaper tray.

7 Push the paper tray firmly back into the copier.

Loading copy paper

LOADING COPY PAPER

Front guide

Left guide

12

GE

TT

ING

STA

RT

ED

Loading copy paper

LOADING COPY PAPER

8 To set the selected paper size, press the PAPER SIZEENTER ( ) key.� The selected paper feed location indicator will blink and the

corresponding paper size (which is currently set) indicator will lightup steadily. All other indicators except the START ( ) keyindicator will go out.

If copying is being performed, paper size setting cannotbe made .

9 AR-5120 only Use the TRAY SELECT ( ) key to selectthe paper tray of which the paper size has beenchanged.� Each time the TRAY SELECT ( ) key is pressed, a paper tray will

be indicated with a blinking paper feed location indicator.

10 Use the ORIGINAL SIZE ENTER ( ) key to selectthe paper size which is set in the paper tray.� Each time the ORIGINAL SIZE ENTER ( ) key is pressed,

a paper size will be indicated with a paper size indicator.

11 Press the START ( ) key and then the PAPER SIZEENTER ( ) key.� AR-5120 only To change the paper size setting of the other tray,

repeat steps 9 to 10 after pressing the START ( ) key.

13

MA

KIN

G C

OP

IES

AUDITING ACCOUNTSIf this copier has been programmed in the auditing mode, it will not functionuntil an assigned 3-digit account number has been entered. See page 39 forsetting the auditing mode.

If the copier has been programmed in the auditing mode, “–––” will appearin the copy quantity display in the initial conditions.

1 Enter your account number using the numeric keys.� As each digit is entered, the dashes in the copy quantity display will

disappear.

� After the number is entered, the copy quantity display will changeto 0.

� If an unassigned number is entered, “–––” will appear again in thecopy quantity display, indicating that the number was not accepted.

2 When copying is completed, press the AUDIT CLEAR( ) key.� “–––” will appear again in the copy quantity display, indicating the

auditing mode.

� In the interrupt copy mode (see page 25), press the INTERRUPT ( )key after an interrupt copy run is completed. All previous copiersettings will be restored and the previous account number will beactive.

Auditing accounts

14

MA

KIN

G C

OP

IES

NORMAL COPYING

1 Turn the power switch on.� It will take about 35 seconds for the copier to warm up. However, you

can make desired settings and press the START ( ) key duringwarm-up. Copying will start after warm-up.

� If the copier has been programmed in the auditing mode, the STARTkey ( ) indicator will not light up and “–––” will appear in the copyquantity display. Enter an assigned 3-digit account number. See page13.

2 Place the original face down on the original table. Alignit with the original size scale.� Image loss (max. 4 mm) can occur at the leading and trailing edges of

the copies. Also image loss (max. 4 mm in total) can occur along theother edges of the copies.

3 Close the platen cover.

4 Ensure that the copy paper size in the paper tray is thesame size as the original.� AR-5120 only Use the ORIGINAL SIZE ENTER ( ) key to

select the original size. Copy paper of the same size as the original willbe automatically selected. If desired, another paper tray can beselected by pressing the TRAY SELECT ( ) key.

� If paper of the required size is not loaded in the paper tray, use thebypass tray and press the TRAY SELECT ( ) key to select thebypass tray.

5 Adjust the copy density.� This copier has three exposure modes to choose from — AUTOMATIC

( ), MANUAL ( ), and PHOTO ( ).

� Automatic exposure is the standard initial setting for this copier. In thismode, the characteristics of the original are “read” by the exposuresystem and adjustments are automatically made. This optimizes thecontrast of the copied images by reducing the effect of coloured orshaded background areas. See page 26 to adjust the automatic exposurelevel.

Norm

al copying

Power on

15

MA

KIN

G C

OP

IES

NORMAL COPYINGN

ormal copying

� For manual copy density adjustment, press the AUTO/MANUAL/PHOTO ( / / ) key to select MANUAL ( ) and adjustwith the light ( ) and dark ( ) keys as desired.

� For photographs, select PHOTO ( ) and then adjust with the light( ) and dark ( ) keys as desired.

� There are 5 exposure steps indicated by 3 indicator lights. (Theindicators light up one or two at a time.)If exposure level 2 is selected, the two left-handmost indicators for thatlevel will light up simultaneously. Also, if level 4 is selected, the tworight-handmost indicators for that level will light up simultaneously.

6 Set the number of copies using the numeric keys.� A single copy can be made with the initial setting, i.e., when “0” is

displayed.

� Press the CLEAR ( ) key to clear an entry if a mistake is made.

� When copying from the optional SPF on AR-5015 N, only one copyper original can be made. The number of copies cannot be changed.

7 Press the START ( ) key.� The number in the copy quantity display will decrease by 1 each time

a copy is made.� Press the CLEAR ( ) key to stop copying in the middle of a run.� To repeat the same copy sequence for a different original, simply

replace the original and press the START ( ) key.� If the paper in the paper tray runs out during the copy run and no other

tray contains the same size paper, the bypass tray can be selected usingthe TRAY SELECT ( ) key.

How to remove the platen cover

The platen cover can be removed to allow copying ofbulky objects. To remove it, simply lift the platen coverstraight up.

� To reattach the platen cover, reverse the above procedure.

16

MA

KIN

G C

OP

IES

Reduction/enlargem

ent/zoom

REDUCTION/ENLARGEMENT/ZOOMReduction and enlargement ratios can be selected either automatically with the AUTO IMAGE ( )key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. Thezoom function enables precise copy ratio selection from 50% to 200% in 1% increments.

Automatic

1 Place the original on the original table and close theplaten cover.

2 Press the ORIGINAL SIZE ENTER ( ) key until theindicator for the size of the original on the original tablelights up.� This feature will not work when copy paper of non-standard size is

used or the bypass tray is used.

3 AR-5120 only Use the TRAY SELECT ( ) key to selectthe paper tray with the desired paper size.

4 Press the AUTO IMAGE ( ) key.� The copy ratio will be automatically set.

� If a PRESET RATIO indicator is blinking, part of the original imagemay not be copied.

If the orientation of the original does not correspond tostandard reduction/enlargement ratios for the selectedpaper tray, then the ORIGINAL SIZE indicator willblink. Change the orientation of the original.

5 Set the number of copies.

6 Press the START ( ) key.

� To cancel the automatic reduction/enlargementmode, press the AUTO IMAGE ( ) key again.

� When copying from an optional SPF with this feature,the automatic reduction/enlargement mode will beautomatically cancelled after copying is complete.

17

MA

KIN

G C

OP

IESREDUCTION/ENLARGEMENT/ZOOM

Reduction/enlargem

ent/zoom

Manual


2 Use the PRESET RATIO selector ( , ) keys and thezoom ( , ) keys to select the desired copy ratio.� To select a preset reduction or enlargement copy ratio, press the

or key repeatedly until the indicator for the desired copy ratio islit.

A. Preset reduction ratios are: 86%, 81%, 70%, and 50%.

B. Preset enlargement ratios are: 115%, 122%, 141%, and 200%.

C. Zoom ratios: Any ratio from 50% to 200% can be set, in 1%increments. Press the or key to set the approximateratio, then press the key to decrease the ratio or the keyto increase the ratio.� When a zoom ( , ) key is pressed, the ZOOM indicator will light

up and the zoom ratio will be displayed in the copy quantity displayfor at least two seconds.

� To verify a zoom setting without changing the zoom ratio, press andhold down the copy ratio display ( ) key. When the key is released,the display will return to the copy quantity display.

� To decrease or increase the zoom ratio rapidly, press and hold downthe or key. However the value will stop at the preset reductionor enlargement ratios. To move beyond these ratios, release the keyand then press and hold it down again.

D. Same-size reset: Press the or key repeatedly until thecopy ratio returns to 100%.

3 Ensure that copy paper of the desired size is installed inthe paper tray.� AR-5120 only Use the ORIGINAL SIZE ENTER ( ) key to

select the original size. Copy paper of the appropriate paper size willbe automatically selected based on the original size and copy ratio. Ifthe selected PRESET RATIO indicator or the ZOOM indicatorblinks,the selected copy image is too large for the copy paper size. Thedesired paper tray can also be selected by pressing the TRAY SELECT( ) key.

4 Set the number of copies and press the START ( ) key.

18

MA

KIN

G C

OP

IES

Bypass feed (special paper)

BYPASS FEED (special paper)The bypass tray is used to copy onto transparency film, labels, and otherspecial purpose papers. Up to 100 sheets of standard copy paper can be setin the bypass tray.

For special purpose papers, the original image must besmaller than the paper or media for copying.If the original image is bigger than the paper or media, thismay cause smudges on the edges of the copies.Also for standard copy paper, smudges may appear if thecopy paper is not at least as large as the original image.

1 Unfold the bypass tray.

� When feeding B4 or A3 sized paper, extend the feeder tray.

2 Set the paper guides to the copy paper width.

3 Insert the copy paper (print face down) all the way intothe bypass tray.� Up to 100 sheets of standard copy paper measuring from A6 to A3 can

be loaded in the bypass tray.� A6 size paper must be fed narrow into the feed slot.� Transparency film, labels, and other special purpose papers (except

envelopes) must be fed individually.Up to 10 envelopes can be set.

� When adding paper, first remove remaining paper, combine it with thepaper to be added and then reload as a single stack.

� When loading envelopes, make sure that they are straight and flat.

19

MA

KIN

G C

OP

IES

BYPASS FEED (special paper)B

ypass feed (special paper)

4 Press the TRAY SELECT ( ) key to select the bypasstray.

5 Leave the copy quantity at 0 if using special papers. Setthe number of copies if using standard copy paper orenvelopes.


20

MA

KIN

G C

OP

IES

Tw

o-sided copying

TWO-SIDED COPYINGTwo-sided copies can be made on this copier using the bypass tray.

1 Place the first original on the original table and make acopy.� The first copy can be made using any of the paper feed stations.

2 Replace the first original with the second original andclose the platen cover.� Make sure that the first and second originals are oriented in the same

way on the original table.

� When the originals are placed horizontally, make sure that the first andsecond originals are oriented in the reverse way on the original table.

3 Turn the first copy over left to right and place it into thebypass tray.� Be sure to feed the copies one sheet at a time.

4 Use the TRAY SELECT ( ) key to select the bypasstray.


21

MA

KIN

G C

OP

IES

XY

zoom

Original Copy

XY ZOOMThe XY ZOOM feature allows the horizontal and vertical copy ratios to bechanged independently.To use the XY ZOOM feature with the DUAL PAGE COPY feature, set theDUAL PAGE COPY feature first and then the XY ZOOM feature.(Enlargement cannot be set.)


2 Press the XY-ZOOM ( ) key.� The current value for the vertical direction will be displayed in the

copy quantity display.

3 Use the PRESET RATIO selector ( , ) keys and zoom( , ) keys to change the copy ratio in the verticaldirection.� Press a PRESET RATIO selector ( or ) key to set an approximate

ratio, then press the key to decrease the ratio or key to increasethe ratio. The copy ratio will be displayed in the copy quantity display.

4 Press the copy ratio display ( ) key.� The selected ratio for the vertical direction will be entered and the

current value for the horizontal direction will be displayed in the copyquantity display.

22

MA

KIN

G C

OP

IES

XY

zoom

XY ZOOM

5 Use the PRESET RATIO selector ( , ) keys and zoom( , ) keys to change the copy ratio in the horizontaldirection in a similar manner as for the vertical direction.

6 Press the copy ratio display ( ) key.� The selected ratio for the horizontal direction will be entered and the

display will change to the copy quantity display.

� To verify the copy ratios, press and hold down the copy ratio display( ) key. The vertical and horizontal ratios will be alternatelydisplayed.

7 Ensure that copy paper of the desired size is installed inthe paper tray.� AR-5120 only Use the ORIGINAL SIZE ENTER ( ) key to

select the original size. Copy paper of the appropriate paper size willbe automatically selected based on the original size and copy ratios.

8 Set the number of copies.� When copying from the optional SPF on AR-5015 N, only one copy

per original can be made. The number of copies cannot be changed.


� To change the copy ratios again, press a PRESETRATIO selector ( , ) key or a zoom ( , )key. Then, perform step 3 and the succeedingsteps.

� To cancel this function, press the XY-ZOOM ( )key again.

23

MA

KIN

G C

OP

IES

B/W

reverse

Original Copy

B/W REVERSEThe B/W REVERSE feature is used to reverse black and white areas.

� When the B/W REVERSE feature is selected, the exposure mode will beautomatically set to the MANUAL mode. Other exposure modes cannotbe selected.Even if this feature is cancelled, the MANUAL mode will notautomatically be cancelled.


2 Press the B/W REVERSE ( ) key.

3 Check the copy paper size.� AR-5120 only Use the ORIGINAL SIZE ENTER ( ) key to

select the original size. Copy paper of the same size as the original willbe automatically selected.

4 Make all other desired copier selections and press theSTART ( ) key.

24

MA

KIN

G C

OP

IES

Dual page copy

Original Copy

DUAL PAGE COPYThe DUAL PAGE COPY feature produces individual copies of two documentsplaced side by side on the original table. It is especially useful when copyingbooks and other bound documents. If the AUTO IMAGE feature has beenselected, this feature cannot be selected.To use the DUAL PAGE COPY feature with the XY ZOOM feature, set theDUAL PAGE COPY feature first and then the XY ZOOM feature.(Enlargement cannot be set.)

1 Place the originals on the original table with the centreof the two pages aligned with the paper size index (A4). Close the platen cover.� Set the page to be copied first to the right of the paper size index mark.

2 Press the DUAL PAGE COPY ( ) key.

3 Check the copy paper size.� The copy paper size must be A4.

4 Set the number of copies.


25

MA

KIN

G C

OP

IES

Interrupting a copy run

INTERRUPTING A COPY RUNINTERRUPT is used to interrupt a long copy run so that another job can bedone.

1 Press the INTERRUPT ( ) key.� The copier will return to the initial settings.� If this copier has been programmed in the auditing mode using user

program No. 10, “–––” will appear in the copy quantity display. Enteryour account number using the numeric keys. The number of copiesof the interrupt copying will be accumulated against this accountnumber. See page 13.

� When an optional SPF is being used, the copier will stop aftercompleting the copying of the original which has been fed into theSPF.

2 When the copier stops, remove the original(s) and setthe original(s) for interrupt copying.

3 Select the desired available copier functions.

4 Set the number of copies.� When copying from the optional SPF on AR-5015 N, only one copy

per original can be made. The number of copies cannot be changed.


6 When all INTERRUPT copies are finished, press theINTERRUPT ( ) key again to cancel the INTERRUPTmode, and remove the original used for interrupt copying.� The previous copy quantity, copy ratio, copy density, and paper size

will be automatically restored.

7 Replace the original(s) for the interrupted job on theoriginal table or in the SPF and press the START ( )key.

26

MA

KIN

G C

OP

IES

Autom

atic exposure adjustment

AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs.This level is set for copying from the original table and copying from theoptional SPF respectively. To set the level for the optional SPF, place anoriginal in the document feeder tray and make sure that the SPF indicatorlights up before proceeding to step 1. To set the level for the original table,ensure that the SPF indicator does not light up.

1 Press the AUTO/MANUAL/PHOTO ( / / ) key toselect the PHOTO ( ) mode.

2 Press and hold down the AUTO/MANUAL/PHOTO ( // ) key for approximately 5 seconds.

� The PHOTO ( ) indicator will go out and the AUTO indicator willbegin to blink.

� One or two exposure indicators corresponding to the current automaticexposure level will light up. The factory default setting is level “3”.

3 Press the light ( ) or dark ( ) key to lighten or darkenthe automatic exposure level as desired.

4 Press the AUTO/MANUAL/PHOTO ( / / ) key.� The AUTO indicator will stop blinking and will light up steadily.

� This automatic exposure level will remain in effect until you changeit again by this procedure.

27

MA

KIN

G C

OP

IES

Toner save m

ode

TONER SAVE MODEThis mode reduces toner consumption by approximately 10% in the automaticand manual exposure modes. Copies will be lighter but still adequate forgeneral use. Selection of this mode does not affect the PHOTO mode. Followthe procedure below for setting the toning level.

1 Press the AUTO/MANUAL/PHOTO ( / / ) key toselect the MANUAL ( ) mode.

2 Press and hold down the AUTO/MANUAL/PHOTO ( // ) key for approximately 5 seconds.

� The MANUAL ( ) indicator will go out and the PHOTO ( )indicator will begin to blink.

� The exposure indicator marked “5” will light up, indicating that thestandard toner mode is active.

3 To enter the toner save mode, press the light ( ) key.� The exposure indicator marked “1” will light up, indicating that the

toner save mode is selected.

4 Press the AUTO/MANUAL/PHOTO ( / / ) key.� The PHOTO ( ) indicator will stop blinking and will light up

steadily. The toner save mode is now active.

� To return to the standard mode, repeat the procedure but use the dark( ) key to select exposure level “5” in step 3.

28

STA

TU

SIN

DIC

ATO

RS

1 Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.

2 Push gently on both sides of the front cover and open it.

3 Push the toner cartridge lock release lever and pull thetoner cartridge out. Remove the toner cartridge whilesupporting it with the left hand at the green label position.� For disposal of the old toner cartridge, contact your dealer.

After removing the toner cartridge, do not shake it or tapon it. Doing so may cause toner to leak from thecartridge. Put the old cartridge immediately in the bagcontained in the box of the new cartridge.

4 Remove the new toner cartridge from the bag. Grasp thecartridge on both sides and shake it horizontally four orfive times. After shaking the cartridge, remove the tape.

Grasp the grip when holding the cartridge. Do not holdthe cartridge by the shutter. Be sure to only shake thecartridge before the tape is removed.

TONER CARTRIDGE REPLACEMENTWhen the toner cartridge replacement required ( ) indicator lights up,replacement of the toner cartridge will be needed soon. Obtain a newcartridge. When the toner cartridge replacement required ( ) indicatorblinks, the toner cartridge must be replaced before copying can be resumed.Replace the toner cartridge by following the procedure below.

For best copying results, be sure to use onlySHARP products.The package of SHARP toner has the GenuineSupplies label.

Toner cartridge replacem

ent

Grip

Toner cartridge lock release lever

4 or 5 times

Tape

Shutter

GENUINE SUPPLIES

During a long copy run of a dark original, the indicator may blink and the copier stop, even thoughtoner is left. The copier will feed toner up to 2 minutesand then the START key ( ) indicator will light up.Press the START ( ) key to restart copying.

29

STA

TU

SIN

DIC

ATO

RS

Toner cartridge replacem

entTONER CARTRIDGE REPLACEMENT

5 Gently insert the toner cartridge along the guides untilit locks in place while pushing the lock release lever.

If dirt or dust is adhered to the toner cartridge, removeit before installing the cartridge.

6 Remove the tape from the shutter. Pull the shutter out ofthe toner cartridge as shown in the illustration. Discardthe shutter.

7 Close the front cover by pushing both sides with yourhands and then close the side cover by pressing thehandle on the cover. The indicator will go out.

When closing the covers, be sure to close the frontcover securely and then close the side cover. If thecovers are closed in the wrong order, the covers maybe damaged.

Even after a new toner cartridge is installed, the STARTkey ( ) indicator may not light up, indicating copyingcannot be restarted (toner is not sufficiently fed). In thiscase, open and close the side cover. The copier willfeed toner again approximately 2 minutes and thencopying can be restarted.

Toner cartridge life

To find out the approximate quantity of toner remaining, follow the procedurebelow.

1 Press and hold the light ( ) key for more than 5seconds until all the alarm indicators ( , , , ,and ) blink and “––” appears in the copy quantitydisplay.

2 Press and hold the copy ratio display ( ) key for morethan 5 seconds.� The approximate quantity of toner remaining will be indicated in the

copy quantity display as a percentage. ( “100”, “75”, “50”, “25”, or“10” is displayed.) When the percentage is less than 10%, “LO” willbe displayed.

3 Press the light ( ) key.� All the alarm indicators will go out.

30

STA

TU

SIN

DIC

ATO

RS

The copier will stop when a misfeed occurs. The misfeed( ) indicator will blink, and blinking red misfeed locationindicators will indicate the approximate misfeed location.If paper is accidentally torn during removal, be sure toremove all pieces.

Be careful not to damage the photoconductive drum.For misfeeds in optional equipment, see its section of theoperation manual.

MISFEED REMOVAL

Misfeed rem

oval

Misfeed in the bypass tray

1 Gently pull the misfed paper out.

2 Lift slightly on the side cover and slide the cover outuntil it stops. Close the side cover by pressing thehandle on the cover.� The misfeed ( ) indicator will go out.

Misfeed in the copier


( P. 58)

( P. 30, 33)

First confirm the misfeed location.

( P. 58)

( P. 34)

( P. 30, 33)

AR-5015 N AR-5120

31

STA

TU

SIN

DIC

ATO

RS

MISFEED REMOVAL M

isfeed removal

If the misfed paper is seen from this side, proceed to C. Misfeed in the transport area .

If paper is misfed here, proceed to B. Misfeed in the fusing area .

If paper is misfed here, proceed to A. Misfeed in the paper feed area .

2 Check the misfeed location. Remove the misfed paperfollowing the instructions for each location in theillustration below.

Roller rotating knob

A. Misfeed in the paper feed area


2 Carefully remove the misfed paper. Turn the rollerrotating knob in the direction of the arrow to assist inremoving it.

The fusing unit is hot. Take care in removing paper.

Do not touch the photoconductive drum (green portion)when removing the misfed paper. Doing so may dam-age the drum and cause smudges on copies.

3 Close the front cover by pushing both sides with yourhands and then close the side cover by pressing thehandle on the cover.� The misfeed ( ) indicator will go out.


B. Misfeed in the fusing area


32

STA

TU

SIN

DIC

ATO

RS

MISFEED REMOVAL

Misfeed rem

oval

2 Turn the roller rotating knob in the direction of thearrow.

3 Carefully remove the misfed paper. Lower the fusingunit release levers to allow easier removal. Return therelease levers to their operating positions.


� Do not touch the photoconductive drum (green portion)when removing the misfed paper. Doing so maydamage the drum and cause smudges on copies.

� Be careful about unfixed toner on the misfed paper notto soil your hands or clothes.

4 Close the front cover by pushing both sides with yourhands and then close the side cover by pressing thehandle on the cover.� The misfeed ( ) indicator will go out.


C. Misfeed in the transport area

1 Open the paper guide by pressing down the projectionon either side of the guide and remove the misfed paper.


2 If the misfed paper cannot be removed by the previousstep but is visible in the paper output area, remove thepaper by pulling it into the paper output area.

Roller rotating knob

Fusing unit release lever

33

STA

TU

SIN

DIC

ATO

RS

MISFEED REMOVAL M

isfeed removal

3 Close the side cover by pressing the handle on thecover.� The misfeed ( ) indicator will go out.

Misfeed in the paper tray (upper paper trayin AR-5120)

Before opening the paper tray, be sure to confirm that there is no misfed paperin the copier. See page 30.

1 Gently lift and pull out the paper tray and remove themisfed paper.

2 Close the paper tray.

3 Lift slightly on the side cover and slide the cover outuntil it stops. Close the side cover by pressing thehandle on the cover.� The misfeed ( ) indicator will go out.

34

STA

TU

SIN

DIC

ATO

RS

Misfeed in the lower paper tray (AR-5120only)

1 Grasp the handle of the lower side cover and gentlyopen the cover.

2 Remove the misfed paper.� Be careful not to tear the misfed paper during removal.

3 If the misfed paper is not seen in step 2, gently lift andpull out the lower paper tray and remove the misfedpaper.� Be careful not to tear the misfed paper during removal.

4 Close the paper tray.

5 Close the lower side cover.� The misfeed ( ) indicator will go out.

Misfeed rem

oval

MISFEED REMOVAL

35

STA

TU

SIN

DIC

ATO

RS

Developer required/

Maintenance required

When the indicator lights up, service by an authorised SHARP servicetechnician is required. Contact your service centre as soon as possible.

When the indicator lights up, the developer should be replaced.DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY ANAUTHORISED SHARP SERVICE TECHNICIAN. Contact your servicecentre as soon as possible.

DEVELOPER REQUIRED

MAINTENANCE REQUIRED

36

GE

NE

RA

L IN

FO

RM

AT

ION

User program

s

USER PROGRAMSThe user programs allow the parameters of certain functions to be set,changed, or cancelled as desired.

List of user programs

This copier has the following user programs.

Program No. Program name Description

1 Auto clear time Sets the auto clear time. The copier returns to the initial settingswhen the auto clear time elapses after the last copy is made.

2 Preheat mode Sets the time that elapses before the copier enters the preheatmode after any operation is made. See page 43.

3 Auto power shut-off Sets the time that elapses before the copier enters the auto powertimer shut-off mode after any operation is made. See page 43.

4 Stream feeding mode* Enables or disables the stream feeding mode when an optionalSPF is installed. See page 57.

5 Auto power shut-off Enables or disables the auto power shut-off mode. See page 43.setting

8 Auto paper select Enables or disables the auto paper selection. See page 7.mode**

9 Auto tray switching** Enables or disables the automatic tray switching which occurs whenpaper in a tray runs out. (This switching cannot switch to the bypass tray.)

10 Auditing mode Enables or disables the auditing mode, which controls access tocopier. See page 13.

11 Account number Registers accounts for auditing mode.entry

12 Account number Changes account numbers for auditing mode.change

13 Account number Deletes accounts for auditing mode.deletion

14 Number of copies Displays the total number of copies made against account numbers.per account

15 Resetting account Resets all audit accounts or resets any desired individual account.

* This program does not affect the copier functions unless certain optional equipment is installed.

** AR-5120 only

37

GE

NE

RA

L IN

FO

RM

AT

ION

Setting the user programs

1 Press and hold the light ( ) key for more than 5seconds until all the alarm indicators ( , , , ,and ) blink and “– –” appears in the copy quantitydisplay.

2 Enter a program number using the numeric keys.� The selected program number will blink in the copy quantity display.

� If a mistake is made in steps 2 to 4, press the CLEAR ( ) key. Thecopier will return to step 2.

� The program numbers are shown in the table below.

For example, to change the setting of the auto power shut-off timer,press key 3.

Program name Program No.Auto clear time 1Preheat mode 2Auto power shut-off timer 3Stream feeding mode 4Auto power shut-off setting 5Auto paper select mode 8Auto tray switching 9Auditing mode 10Account number entry 11Account number change 12Account number deletion 13Number of copies per account 14Resetting account 15

USER PROGRAMSU

ser programs

For operation of these programs afterstep 3, see page 39.

3 Press the START ( ) key.� For programs 1 to 9, the entered program number will be steadily lit

on the left side of the copy quantity display and the currently selectedparameter number for the program will blink on the right side.

� For programs 10 to 15 (programs for auditing accounts), the displayvaries with the program number. See page 39 for setting programs 10to 15.

38

GE

NE

RA

L IN

FO

RM

AT

ION

USER PROGRAMS

User program

s

4 Select the desired parameter using the numeric keys.� The entered parameter number will blink on the right side of the copy

quantity display.

� The parameters are shown in the table below.

For example, to change the setting of the auto power shut-off timer to60 min., press key 2.

If you select “0” (OFF) in a program, the correspondingfunction will be disabled.

5 Press the START ( ) key.� The right-hand number in the copy quantity display will be steadily lit

and the entered value will be stored.

6 To continue with other user programs, press the keyand then repeat steps 2 to 5. To exit the user programmode, press the light ( ) key.� All the alarm indicators will go out.

Program name Parameters

Auto clear time 0 OFF 1 30 sec. * 2 60 sec. 3 90 sec. 4 120 sec.5 10 sec.

Preheat mode 0 OFF 1 30 sec. 2 60 sec. * 3 90 sec. 4 120 sec.

Auto power shut-off timer * 1 30 min. 2 60 min. 3 90 min. 4 120 min. 5 240 min.

Stream feeding mode * 0 OFF 1 ON

Auto power shut-off setting 0 OFF * 1 ON

Auto paper select mode 0 OFF * 1 ON

Auto tray switching 0 OFF * 1 ON

� Factory default settings are indicated with an asterisk (*).

39

GE

NE

RA

L IN

FO

RM

AT

ION

USER PROGRAMSU

ser programs

Settings for auditing accounts

Settings of user programs No. 10 to 15 varies with the program number. Forsetting of all programs, first follow steps 1 to 3 in “Setting the user programs”on page 37 to select a program. (1. Press the light ( ) key for more than 5seconds. 2. Enter a program number (10 to 15) using the numeric keys. 3.Press the START ( ) key.) Then follow the appropriate instructions for theprogram.

Program No. 10: Auditing mode

If the auditing mode is enabled, copying is limited to operators with anassigned 3-digit account number. A maximum of 20, 3-digit accountnumbers can be assigned. Use program No. 11 to register account numbers.When program No. 10 is entered, the current setting (0: OFF, 1:ON) willblink on the right side of the copy quantity display.

1. Select the desired setting using the numeric keys.0: OFF1: ON

2. Press the START ( ) key.� The setting will be stored.

3. To continue with other user programs, press the keyand enter another program number. To exit the userprogram mode, press the light ( ) key.

Program No. 11: Account number entry

Program No. 11 is used to register accounts. When program No. 11 is entered,“–––” will blink in the copy quantity display.� If the number of accounts has reached the upper limit (20), “11E” will

appear in the copy quantity display. Press the key. The copier willreturn to step 2 on page 37.

1. Enter a 3-digit account number using the numeric keys.� Any 3-digit number except “000” can be registered as an account

number.

2. Press the START ( ) key.� If a number that is already registered or “000” is entered, the number

will blink in the copy quantity display.

3. Repeat steps 1 and 2 for other account numbers.


40

GE

NE

RA

L IN

FO

RM

AT

ION

USER PROGRAMS

User program

s

Program No. 12: Account number change

Program No. 12 is used to change account numbers. When program No. 12is entered, an account number will appear in the copy quantity display.� If no account number has been registered, “12E” will appear in the copy

quantity display. Press the key. The copier will return to step 2 on page37.

1. Use the copy ratio display ( ) key to select the accountnumber to be changed.� Use the key to advance through the account numbers.

2. Press the START ( ) key.� The account number will be erased and “–––” will blink in the copy

quantity display.

3. Enter a new account number using the numeric keys.

4. Press the START ( ) key.� If a number that is already registered or “000” is entered, the number

will blink in the copy quantity display.

5. Repeat steps 1 to 4 for other account numbers.


Program No. 13: Account number deletion

Program No. 13 is used to delete accounts. When program No. 13 is entered,“0” will blink on the right side of the copy quantity display.� If no account number has been registered, “13E” will appear in the copy


1. To delete an individual account, press the 0 key.To delete all accounts, press key 1.

2. Press the START ( ) key.� If you have pressed the 0 key in step 1, an account number will appear

in the copy quantity display. Proceed to step 3.

� If you have pressed key 1, all account numbers will be deleted.Proceed to step 5.

3. Use the copy ratio display ( ) key to select the accountnumber to be deleted.� Use the key to advance through the account numbers.

4. Press the START ( ) key.� The specified account will be deleted.

5. To continue with other user programs, enter anotherprogram number. To exit the user program mode, pressthe light ( ) key.

41

GE

NE

RA

L IN

FO

RM

AT

ION

User program

sUSER PROGRAMS

Program No. 14: Number of copies per account

Program No. 14 is used to display the total number of copies made againsteach account number. When program No. 14 is entered, an account numberwill appear in the copy quantity display.� If no account number has been registered, “14E” will appear in the copy


1. Use the copy ratio display ( ) key to select the accountnumber.� Use the key to advance through the account numbers.

2. Press and hold down the 0 key.� The number of copies made against the specified account number will

be displayed. The two higher digits and the three lower digits willappear alternately while the 0 key is pressed.

Example: 1,234 copies

� The upper limit for the number of copies is 49,999. If the number ofcopies made reaches 50,000, the number will be reset to 0 and countingwill start again from 0.

3. Repeat steps 1 and 2 for other account numbers.

4. To continue with other user programs, press the keyand select another program number. To exit the userprogram mode, press the light ( ) key.

42

GE

NE

RA

L IN

FO

RM

AT

ION

USER PROGRAMS

User program

s

Program No. 15: Resetting account

Program No. 15 is used to reset all accounts or to reset any desired individualaccount. When program No. 15 is entered, “0” will blink on the right side ofthe copy quantity display.� If no account number has been registered, “15E” will appear in the copy

quantity display. Press the key. The copier will return to step 2 onpage 37.

1. To reset an individual account, press the 0 key.To reset all accounts, press key 1.

2. Press the START ( ) key.� If you have pressed the 0 key in step 1, an account number will appear

in the copy quantity display. Proceed to step 3.

� If you have pressed key 1, the number of copies against all accountnumbers will be reset. Proceed to step 5.

3. Use the copy ratio display ( ) key to select the accountnumber to be reset.� Use the key to advance through the account numbers.

4. Press the START ( ) key.� The number of copies against the specified account number will be

reset.

5. To continue with other user programs, enter anotherprogram number. To exit the user program mode, pressthe light ( ) key.

43

GE

NE

RA

L IN

FO

RM

AT

ION

Power save m

odes

POWER SAVE MODESThe copier has two power save modes to reduce overall power consumptionthereby reduce the cost of operation. In addition, these modes conservenatural resources and help reduce environmental pollution. The two powersave modes are preheat mode and auto power shut-off mode.

� User programsThe preheat activation time and the auto power shut-off time have beenpreset at the factory to 90 sec. for preheat mode and 30 min. for auto powershut-off mode. These times can be changed using user programs. It issuggested that you set appropriate times according to the actual usage ofthe copier. See page 36.

Preheat mode

When the copier enters the preheat mode, the POWER SAVE ( ) indicatorwill light up and other indicators will remain on or off as before. In thiscondition, the fuser in the copier is maintained at a lower heat level, therebysaving power. The preheat level is, however, high enough to allow the copierto come to a ready condition or begin copying within 10 seconds after anykey input or copier operation such as paper tray operation is performed.

Auto power shut-off mode

If the auto power shut-off mode is enabled, the copier will automatically turnoff the power once a programmed length of time has elapsed without anycopier operation after the last copy of a run is made or the power is first turnedon. The power switch will automatically be turned to the “OFF” position.To turn the power back on, simply turn the power switch to the “ON”position.

44

GE

NE

RA

L IN

FO

RM

AT

ION

Power save m

odes

POWER SAVE MODES

Setting the power save modes

The time that elapses before the copier enters a power save mode after anyoperation is made can be set manually. This time is set with user program No.2 for the preheat mode and user program No. 3 for the auto power shut-offmode. For these settings, see page 37.

� The copier will enter the preheat mode first and then the auto powershut-off mode after a preset time has elapsed when no copier operationhas been made.

� If conflicting settings are made with user programs No. 3 and No. 5, thelast program set will have priority.

Copying from the preheat mode

Make desired copier selections and press the START( ) key using the normal copying procedure.� When any key input is made or any other copier operation is made, the

POWER SAVE ( ) indicator will start to blink.� When the START key is pressed, the START key ( ) indicator will

go out and copying will start within 10 seconds. The POWER SAVE( ) indicator will go out when copying starts.

45

GE

NE

RA

L IN

FO

RM

AT

ION

User m

aintenance

Bypass tray paper feed roller

If misfeeds occur frequently when feeding postcards,envelopes, thick paper, etc. through the bypass tray,wipe the blue paper feed roller at the feed slot of thebypass tray with a soft, clean cloth dampened withalcohol or water.

Paper feed roller

USER MAINTENANCEProper care is essential for clean, sharp copies. Please take a few minutes toregularly clean your copier.

Original table and platen cover

Stains or dirt on the original table or platen cover willalso be copied. Wipe the original table and platen coverwith a soft, clean cloth.

� If necessary, dampen the cloth with water. Do not use thinner,benzene, or similar volatile cleaning agents.

� If an optional SPF is installed, wipe the scanning window on theoriginal table.

46

GE

NE

RA

L IN

FO

RM

AT

ION

User m

aintenance

Charger cleaner

USER MAINTENANCE

Transfer charger cleaning

If copies start becoming streaky or blotchy, the transfer charger may be dirty.Clean the charger using the following procedure.

1 Turn the power switch off.


3 Gently lift and pull out the paper tray (upper paper trayin AR-5120) and take the charger cleaner out by holdingthe tab.

4 Set the charger cleaner onto the transfer charger andgently slide the cleaner in the direction indicated by thearrow two or three times.

Slide the charger cleaner from one end to the other endalong the groove of the transfer charger. If the cleaneris stopped on the way, smudges on copies may occur.

� If the white sheet metal is smudged with toner, wipe it with a soft, cleancloth.

5 Return the charger cleaner to its original position.Close the paper tray. Close the side cover by pressingthe handle on the cover.

6 Turn the power switch on.

47

GE

NE

RA

L IN

FO

RM

AT

ION

Problem Solution

� Copier plugged in?

� Power switch ON?

� Copy density properly adjusted?

� Is the original placed face down?

� Paper too heavy?

� Paper damp?

� Is transfer charger clean?

� Non-standard paper used?

� Paper properly installed?

� Pieces of paper inside copier?

� Paper curled or damp?

Plug the copier into a grounded outlet.See page 8.

Turn the power switch ON.See page 14.

See pages 14 and 26.

Place the original face down on the originaltable.

Use copy paper within the specified range. Seepage 50.

Replace with dry copy paper.Be sure to store copy paper in a dry location. Seepage 51.

Clean the transfer charger.See page 46.

Use standard paper. If using special paper, feedthe paper through the bypass tray.See pages 18 and 50.

Make sure the paper is properly installed. Seepages 10 and 18.

Remove all pieces of misfed paper.See page 30.

Store copy paper flat in the wrapper in a drylocation. See page 51.

Copier does not operate.

Copies are too dark ortoo light.

Blank copies

Paper misfeeds frequently.

Copies smear if rubbed.

COPIER TROUBLE?C

opier trouble?

Striped copies

48

GE

NE

RA

L IN

FO

RM

AT

ION

Problem Solution

� Original table or platen cover dirty?

� Original smudged or blotchy?

� Is the indicator on?


� Is copying being performed?

� Is the POWER SAVE ( ) indicatorblinking?

� Is steadily lit in the copyquantity display?


Clean regularly. See page 45.

Use a clean original.

Developer is required. Contact your SHARPservice centre as soon as possible. See page 35.

Maintenance is required. Contact your SHARPservice centre as soon as possible.See page 35.

Set the paper size after copying is complete.

Wait until warm-up is complete.Warm-up time is approximately 35 seconds.

The copier is in the auditing mode.Enter your account number using the numerickeys. See page 13.

Copy paper is needed. See page 10,LOADING COPY PAPER.

Copies are smudged ordirty.

Power is on but copyingis not possible.

Copier trouble?

COPIER TROUBLE?

Paper size for a papertray cannot be set.

49

GE

NE

RA

L IN

FO

RM

AT

ION

A toner cartridge is not installed. Install a tonercartridge. If "CH" is blinking even if acartridge is installed properly, contact yourSHARP service centre immediately.

The side cover is open.Close the front and side covers securely.

The toner cartridge must be replaced. See page28, TONER CARTRIDGE REPLACEMENT.

A misfeed has occurred. See page 30,MISFEED REMOVAL.

Connect the copier to a power outlet which isnot used for other electric appliances.

� Is blinking in the copyquantity display?

� Is steadily lit in the copyquantity display?

� Is the indicator blinking?

� Is the indicator blinking?

� Is the same power outlet used forthe lighting fixture and the copier?

Problem Solution

Power is on but copyingis not possible.

Lighting fixture flickers.

Copier trouble?

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should thecopier malfunction, the self-diagnostic function will locate the problem andstop the copier to prevent damage. An alphanumeric code will appear in thecopy quantity display.

Example

Should the copier completely stop and a letter and a number appear alternately,contact your SHARP service centre immediately.

COPIER TROUBLE?

Be sure to use only genuine SHARP parts and supplies.

Please contact your SHARP service centre immediately if a problem persistsafter checking the above.

50

GE

NE

RA

L IN

FO

RM

AT

ION

SUPPLIES

Types and sizes of copy paper

Size Weight Capacity (80 g/m2 Special paperpaper)

Paper tray A5* to A3 56 to 80 g/m2 250 sheets

Bypass tray Ordinary paper: 56 to 128 g/m2** 100 sheets Transparency film,A6 to A3 (Ordinary paper) labels, envelopes***

Envelopes:International DL(110 x 220 mm)International C5(162 x 229 mm)Commercial 10(4-1/8" x 9-1/2")

* A5 copy paper cannot be used in the lower paper tray of AR-5120.

** For paper weighing from 105 to 128 g/m2, A4 is the maximum size thatcan be fed through the bypass tray.

*** Do not use envelopes that have metal clasps, plastic snappers, stringclosures, windows, linings, self-adhesive patches or synthetic materials.These will cause physical damage to the copier.

� For best results, use only paper recommended by SHARP.

� Special papers except envelopes must be fed one sheet at a time throughthe bypass tray. Up to 10 envelopes can be set at one time.

Supplies

51

GE

NE

RA

L IN

FO

RM

AT

ION

SUPPLIES

Genuine supplies statement

Standard supplies for this copier that are to be replaced by the user are copypaper and toner cartridge.

For best copying results, be sure to use onlySHARP products.Only genuine SHARP consumables carrythe Genuine Supplies label.

GENUINE SUPPLIES

Proper storage

1. Store the supplies in a location that is:� clean and dry,

� at a stable temperature,

� not exposed to direct sunlight.

2. Store copy paper in the wrapper and lying flat.� Paper stored out of the wrapper or in packages standing on end may

curl or get damp, resulting in paper misfeeds.

Supplies

52

GE

NE

RA

L IN

FO

RM

AT

ION

SPECIFICATIONS

Specifications

Type Digital laser copier, desktop

Copy system Dry, electrostatic transfer

Originals Sheets, bound documents

Original sizes Max. A3

Copy sizes Max. A3Min. A6Image loss: Max. 4 mm (leading and trailing edges)

Max. 4 mm (along other edges in total)

Copying speed AR-5015 N: AR-5120: (at 100% copy ratio) 15 copies/min. (A4) 20 copies/min. (A4)

12 copies/min. (A4R) 14 copies/min. (A4R)10 copies/min. (B4) 12 copies/min. (B4)

9 copies/min. (A3) 11 copies/min. (A3)

Continuous copy Max. 99 copies; subtractive counter

First-copy time 7.2 seconds (except in a power save mode)

Warm-up time Approx. 35 seconds

Copy ratio Variable: 50% to 200%, in 1% increments (total 151 steps)Fixed preset: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200%

Exposure system Moving optical source, slit exposure (stationary platen) with automaticexposure function

Copy paper feed One (AR-5015 N) or two (AR-5120) paper trays with automatic feed (250sheets each), one bypass tray with automatic feed (100 sheets)

Fusing system Heat roller

Developer system Magnetic brush development

Light source Xenon lamp

Resolution Scan: 400 dpiOutput: 600 dpi

Gradation Scan: 256 levelsOutput: 2 levels

Power supply Local voltage ±10% (For this copier’s power supply requirements, see thename plate located on the back of the unit.)

Power consumption Max. 1.3 kW

53

GE

NE

RA

L IN

FO

RM

AT

ION

SPECIFICATIONSSpecifications

� First-copy time may differ depending on operating conditions, such as power-supply voltage androom temperature.

As a part of our policy of continuous improvement, SHARP reserves the rightto make design and specification changes for product improvement withoutprior notice. The performance specification figures indicated are nominalvalues of production units. There may be some deviations from these valuesin individual units.

Overall dimensions 590 mm (W) x 531 mm (D)(with bypass tray folded)

Weight AR-5015 N: Approx. 32 kgAR-5120: Approx. 36.5 kgToner cartridge included

Copier dimensions AR-5015 N: 590 mm (W) x 531 mm (D) x 470 mm (H)AR-5120: 590 mm (W) x 531 mm (D) x 552 mm (H)

Operating conditions Temperature: 15°C to 30°CHumidity: 20% to 85%

Acoustic noise emission Sound power level LWA

(measurement according Operating: 6.1 [B], Standby: 3.2 [B]to ISO 7779) Sound pressure level LPA (Bystander positions)

Operating: 47 [dB (A)], Standby: 17 [dB (A)]Sound pressure level LPA (Operator positions)Operating: 50 [dB (A)], Standby: 18 [dB (A)]

Emission concentration Ozone: less than 0.02 mg/m3

(measurement according to Dust: less than 0.075 mg/m3

RAL-UZ 62) Styrene: less than 0.07 mg/m3

Optional equipment Single pass feeder (AR-SP2)

54

GE

NE

RA

L IN

FO

RM

AT

ION

MEMO

55

OP

TIO

NA

LE

QU

IPM

EN

T

OPTIONALEQUIPMENT

CONTENTSPage

� SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . . . . . 56� Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56� Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56� Using the SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57� Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

56

OP

TIO

NA

LE

QU

IPM

EN

T

SINGLE PASS FEEDER (AR-SP2)The single pass feeder (SPF) holds up to 30 originals for automatic feeding.

Single pass feeder (AR

-SP2)

PART NAMES

Specifications

Acceptable Weight: 56 to 90 g/m2

originals Size: A5 to A3Capacity: Up to 30 sheets provided the total aggregate thickness

does not exceed 4 mm

Detectable original A5, A4, A4R, B4, A3sizes

Power supply Drawn from the copier

Weight Approx. 5.3 kg

Dimensions 583 mm (W) x 435 mm (D) x 131 mm (H)

Document feeder tray Feeding roller cover

Right side cover

Original guides

Exit area

As a part of our policy of continuous improvement, SHARP reservesthe right to make design and specification changes for productimprovement without prior notice. The performance specificationfigures indicated are nominal values of production units. There maybe some deviations from these values in individual units.

57

OP

TIO

NA

LE

QU

IPM

EN

TSINGLE PASS FEEDER (AR-SP2)

Using the SPF

� Be sure to remove any staples or paper clips from theoriginals.

� Damaged or crumpled originals may misfeed in the SPF.It is recommended that these originals be copied from theoriginal table.

� Before placing curled or wavy originals into the documentfeeder tray, be sure to flatten them. If not, original misfeedsmay result.

� For best feeding of originals which have binding holespunched into them, insert them so that the holes arepositioned to the right or along the side guides.

� Special originals such as transparency film and tracingpaper should not be fed through the SPF but should becopied from the original table.

1 Ensure that no original is left on the original table.

2 Adjust the original guides to the size of the originals.

3 Set the originals face up in the document feeder tray.� The SPF indicator will light up. If this indicator does not light up, the

originals are not properly set or the SPF is not properly closed.

4 Ensure that the copy paper size in the paper tray is thesame size as the originals.� AR-5120 only A paper tray with the corresponding paper size will be

automatically selected.

5 Set the number of copies (AR-5120 only) and press theSTART ( ) key.� With AR-5015 N, only one copy per original can be made. The number

of copies cannot be changed.� The AR-5120 copier is equipped with a 1-page memory buffer. The

number of copies can be specified.

While making copies from the SPF, do not placeoriginals of the next copying job. Place them after allcopies of the current job have been output.

� Press the CLEAR ( ) key to stop copying in the middle of a run.


-SP2)

Stream feeding modeIf the stream feeding mode has been enabled using user programNo. 4, the SPF indicator will continue to blink for approximately5 seconds after feeding of all originals is completed. While thisindicator is blinking, any new originals placed in the SPF will befed and copied automatically. See page 36, USER PROGRAMS.

58

OP

TIO

NA

LE

QU

IPM

EN

T

SINGLE PASS FEEDER (AR-SP2)

Misfeed removal

Location A

Location B

Location C


-SP2)

If an original misfeed occurs in the SPF, the copier willstop and the red indicator which indicates an originalmisfeed will blink.

1 Open the feeding roller cover and pull the original gentlyto the left and out from the document feeder tray. Closethe feeding roller cover.

2 If the misfed original cannot be removed in step 1, openthe right side cover and remove the misfed original.Close the right side cover.

3 If the misfed original cannot be removed in steps 1 and2, remove the misfed original from the exit area. Openthe document feeder cover and rotate the roller in thedirection indicated by the arrow if needed.If the misfed original cannot be easily removed from theexit area, open the front part of the document feeder trayto remove the original.

4 Open and close the document feeder cover to cancel themisfeed location indicator.

After misfed originals are removed, a number mayappear in the copy quantity display, indicating thenumber of originals that must be returned to thedocument feeder tray. Return the originals and pressthe START ( ) key to resume copying.

A

C

B

Feeding roller cover

Right side cover

Roller

59

AAuto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 36Automatic exposure adjustment . . . . . . . . . . . . . . . . . . 26Auto power shut-off mode . . . . . . . . . . . . . . . . . . . . . . 43

BB/W reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CCautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Copier trouble? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Copying– large original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15– normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14– reduction/enlargement . . . . . . . . . . . . . . . . . . . . . . . . 16– through bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . 18– two-sided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 50Copy quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DDark key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Developer replacement required indicator . . . . . . . . . . 35Dual page copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

EEnlargement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Exposure adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 14

FFeatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Fixed copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Fusing unit release lever . . . . . . . . . . . . . . . . . . . . . . . . 32

IInitial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

LLight key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 29, 37Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

MMaintenance– user maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45– maintenance required indicator . . . . . . . . . . . . . . . . . 35Manual exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Manual feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Misfeed removal– bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30– in the copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30– paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33– SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

NNames– operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6– part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

OOperation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PPaper– loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10– special . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18– specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Paper output tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Paper size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Photo mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Power save modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Preheat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

RReduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Replacement– toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

INDEXIndex

60

SSpecial paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Specifications– copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52– paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Storage of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

TToner cartridge life . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Toner cartridge replacement . . . . . . . . . . . . . . . . . . . . . 28Toner save mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Total output count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Two-sided copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

UUser maintenance– bypass tray paper feed roller . . . . . . . . . . . . . . . . . . . 45– original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45– platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45– transfer charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46User programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

XXY zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

ZZoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

INDEX

Index

61

MEMO

CLASS 1LASER PRODUCT

LASER KLASSE 1

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

CAUTIONVORSICHTADVARSEL

ADVERSELVARNINGVARO!

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.AVOID EXPOSURE TO BEAM.

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UNDSICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGA UDSAETTELSE FOR STRÅLING.

USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄLASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

Laserstrahl

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/EEC.

Dette produktet oppfyller betingelsene i derektivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.

The CE mark logo label is affixed on an equipment in case that the directives described in theabove sentence are applicable to the product. (This sentence is not applicable in any countrywhere the above directives are not required.)

In some areas, the “POWER” switch positions are marked “ I ” and “ ” on the copier instead of “ON” and “OFF”.If your copier is so marked, please read “ I ” for “ON” and “ ” for “OFF”.Caution!For a complete electrical disconnection, pull out the main plug.The socket-outlet shall be installed near the equipment and shall be easily accessible.

Warning

This is a Class A product. In a domestic environment this product may cause radiointerference in which case the user may be required to take adequate measures.

PRINTED IN CHINA2002L KS TINSE0806QSZZ

SHARP CORPORATION

AR-5015 N/AR-5120

Printed on 100% post-consumer recycled paper

MODEL AR-5015 N AR-5120 - sharp.eu€¦ · •getting started • making copies • status indicators • general information • optional equipment 2 13 28 36 55 digital laser copier

Documents