XIX International Symposium on Theoretical Electrical Engineering July 16 - 19, 2017, Ilmenau, Germany TO3-3 Abstract— A semi-analytical method to analyze post-wall waveguides and circuits is presented. The propagation constant of the fundamental TE mode, the attenuation constant due to transversal leakage loss and the effective width of an equivalent rectangular waveguide are calculated. The S-parameters of post-wall passive circuits such as e.g. bandpass filters are analyzed using the image theory combined with the lattice sums technique. Index Terms— compact bandpass filters, modal analysis, periodic structures, post-wall waveguide. I. INTRODUCTION The post-wall waveguide is formed by periodically distributed (usually metallic) posts or posts with a high dielectric permittivity [1]. It allows the “planarization” of non-planar structures such as conventional rectangular waveguides and they can completely be integrated together with planar structures onto the same substrate with the same processing or fabrication techniques. Functional post-wall circuits are designed by inserting additional metallic or dielectric posts into the post-wall waveguide. II. FORMULATION AND DISCUSSIONS The post-wall waveguide is confined by two N-layered square lattice of conducting circular posts (each forming a planar lattice) embedded in a dielectric substrate that is vertically bounded by two parallel conducting plates (Fig.1). The electromagnetic fields are uniform in the y- direction ( 0 y ) and the dominant mode 10 TE is excited. If we assume a longitudinal field variation of e i z , the guided wave propagating within the waveguide channel /2 a x is expressed as follows: + (,) (,) (,) U U y xz xz xz E c c (1) with (,) exp ( / 2) exp( ) m xz i x a i z U (2) ( 0, 1, 2, ) c c (3) where 2 2 0 2 / , , , s s s h k k s is the permittivity of the dielectric substrate, stands for the propagation constant, and c are the column vectors whose elements represent the amplitudes of the transversally up-going and down-going -th Floquet mode. The dispersion equation to determine the mode propagation constant is expressed as follows [2]: det[ ( , ) ( , )] 0 N I W R (4) where the signs stand for even (–) and odd (+) modes, respectively, , ( ) N R denotes the generalized reflection matrix of the confining N-layered periodic arrays of circular rods and ( , ) W denotes the phase shift along x- axis. Solving dispersion equation based on a perturbation analysis, the attenuation constant (due to the leakage loss) and the effective width of the equivalent rectangular waveguide are calculated. To validate the proposed formalism, numerical examples for post-wall waveguides and post-wall waveguide-based passive circuit, such as bandpass filter, are presented and compared to those reported in the references yielding a perfect agreement between the S-parameters over a wide frequency range. It is important to mention that the proposed semi-analytical formulation is not time-consuming, which could be considered as a major advantage of the proposed formulation. The proposed method is a very apt tool for designing advanced multi-functional, ultra-compact submillimeter passive circuit devices. REFERENCES [1] D. Deslandes and K. Wu, “Accurate modeling, wave mechanisms, and design considerations of a substrate integrated waveguide,” IEEE Trans. Microwave Theory Tech., vol. 54, no. 6, pp. 2516- 2526, 2006. [2] K. Yasumoto, H. Maeda and V. Jandieri, “Analysis of Post -Wall Waveguides Using a Model of Two-Dimensional Photonic Crystal Waveguides,“ Proceedings of the IEEE International Conference on Signal Processing and Communication (ICSC-2015), Noida, India, pp. 74-79, April, 2015. Modal Analysis of Post-Wall Waveguides and Compact Circuits Vakhtang Jandieri 1 , Hiroshi Maeda 2 , Kiyotoshi Yasumoto 2 and Daniel Erni 1 1 General and Theoretical Electrical Engineering (ATE), Faculty of Engineering, University of Duisburg-Essen, and CENIDE – Center for Nanointegratin Duisburg-Essen, D-47048 Duisburg, Germany 2 Department of Information and Communication Engineering, Fukuoka Institute of Technology, Fukuoka, Japan E-mail: [email protected]Fig. 1. Schematic of a post-wall waveguide bounded by two adjacent N-layered post-wall arrays. - 63 -
22
Embed
Modal Analysis of Post-Wall Waveguides and Compact … · rectangular waveguide are calculated. ... formalism, numerical examples for post-wall waveguides and post-wall waveguide-based
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
XIX International Symposium on Theoretical Electrical EngineeringJuly 16 − 19, 2017, Ilmenau, Germany TO3-3
Abstract— A semi-analytical method to analyze post-wall waveguides and circuits is presented. The propagation constant of the
fundamental TE mode, the attenuation constant due to transversal leakage loss and the effective width of an equivalent
rectangular waveguide are calculated. The S-parameters of post-wall passive circuits such as e.g. bandpass filters are analyzed
using the image theory combined with the lattice sums technique.
[1] D. Deslandes and K. Wu, “Accurate modeling, wave mechanisms,
and design considerations of a substrate integrated waveguide,”
IEEE Trans. Microwave Theory Tech., vol. 54, no. 6, pp. 2516-
2526, 2006.
[2] K. Yasumoto, H. Maeda and V. Jandieri, “Analysis of Post-Wall
Waveguides Using a Model of Two-Dimensional Photonic Crystal
Waveguides,“ Proceedings of the IEEE International Conference
on Signal Processing and Communication (ICSC-2015), Noida,
India, pp. 74-79, April, 2015.
Modal Analysis of Post-Wall Waveguides and
Compact Circuits Vakhtang Jandieri1, Hiroshi Maeda2, Kiyotoshi Yasumoto2 and Daniel Erni1
1General and Theoretical Electrical Engineering (ATE), Faculty of Engineering, University of Duisburg-Essen, and
CENIDE – Center for Nanointegratin Duisburg-Essen, D-47048 Duisburg, Germany 2 Department of Information and Communication Engineering, Fukuoka Institute of Technology, Fukuoka, Japan
Fig. 1. Schematic of a post-wall waveguide bounded
by two adjacent N-layered post-wall arrays.
− 63 −
Modal Analysis of Post-Wall Waveguides and Compact Circuits
Vakhtang Jandieri1, Hiroshi Maeda2, Kiyotoshi Yasumoto2 and Daniel Erni1
1 General and Theoretical Electrical Engineering (ATE) and CENIDE – Center Nanointegration Duisburg-Essen, Duisburg, Germany
2 Department of Information and Communcation Engineering, Fukuoka Institute of Technology, Fukuoka, Japan
ISTET 2017Ilmenau, Germany
18th July, 2017
1. Background
2. Model of 2D-Photonic Crystal Waveguide
3. Analysis of Post-wall Waveguides
4. Attenuation Constant and Leakage Loss
5. Numerical Examples for Post-Wall Waveguides
6. Numerical Examples for Compact Circuits
7. Conclusions
Content
Two-dimensional model fields The posts may be assumed to be infinitely long. Mode fields like modes in rectangular waveguide
Planar microwave (millimeter wave) circuitsb λ�
( / 0)y∂ ∂ =
0TEm
passive element
rectangularwaveguide
rectangularwaveguideconducting plate
conducting platedielectric substrate
metallic post
z x
y
bh
2r
aµ 0ε s
1. Background
Hirokawa and M. Ando, “ Single-layer feed waveguide consisting of posts for plane TEM wave Excitation in parallel plates,” IEEE Trans. Antennas Propagat., vol. 46, no. 5, pp.625-630, 1998.
A very good alternative of the conventional non-planar guiding devices is a Post-Wall Waveguide also calledSubstrate Integrated Waveguide. It allows the “planarization” of non-planar structures such as rectangularwaveguides and they can completely be integrated together with planar structures onto the same planarsubstrate with the same processing or fabrication techniques.
2D-Photonic Crystals
Photonic crystal
Unit cell
zx
x
z
Photonic crystal waveguide
2. Model of Photonic Crystal Waveguides
x
z
hx
N
N
h
( , )N β ωR
( , )N β ωRa
Dielectric or conductor circular rods of infinite length
conducting plate
conducting platedielectric substrate
metallic post
z x
y
bh
a
2r
µ 0ε s
1-layer structure
a
h2r
ε µ0,s
z
x
Consider TE modes. If we assume a longitudinal field variation of exp(iβz), the two-dimensional guided wave propagating along the guiding region |x| < a/2, is expressed as follows:
[ ]
+
2 20
( , ) ( , ) ( , )
( , )
2 / , , ,
exp ( ( / 2)) exp( )
y
lm
s s s
x z x z x z
x z
h k k
E
i x a i z
β β π κ β ω ε µ
κ β δ
+ − −
±
= ⋅ + ⋅
=
= + = − =
U U
U � �
� � ��
∓
c c
[ ], ,( ) ( )
,( ) exp( )
N
mi aω β ω β
ω β κ δ
± ⋅=
=
W R
W
∓
� �
c c
2 2
0
det[ ( , ) ( , )] 0 (1)
( , ) [e ], ( 2 / ) (2)
( , ) : Generalized r
l
N
lm l s
s s
N
i a k l h
k
κ
β ω β ω
β ω δ κ β π
ω ε µ
β ω
− =
= = − +
=
I W R
W
R
Rigorous Formulation
000
eflection matrix of -layered post walls
1 e ( , ) 0
Only the f
(3)
unda
i a N
N
Rκ β ω− =
Long Wavelengths Approxination
mental Floquet mode with 0 is propagating and all other Floquet modes are evanescent.
l =
3. Analysis of Post-wall Waveguides
0 00
00 00
00
1 e ( , ) 0 ( ) (4)
( , ) 1.0 and ( , ) 1.0 (5)
( )
( , )
Ni a
N N
N
R
R R
R
κ β ω β ω
β ω β ω
β ω
β ω
− ⇒=
≤
Mode propagation constant
Properties of
�
0 000
200
( )
1 ( , ) small perturbation related to leakage
( , ) 1 e e 1
N e
N
i a a i a
e
R
a a
R
a
κ κ
β ω
β ω − +∆ −
−
= +
= − = = −
⇒
⇒
∆ Effective width:
Equivalent rectangular waveguide
0 (for and satisfying Eq.(3)) (6) ea π ω β
κ=
4. Attenuation Constant
0 0(
Let us introduce a small attenuation constant of the guided wave due to the leakage and express the propagation constant as:
)the attenuation constant due to the leakage is given as fol
a)
iβ β α α β= + <<
000 0
0
2
0 00
0 00
ln ( , )
0.5
lows:
(7)
The attenuation constant also can be calculated using a perturbation analysis taking into account the principle of power conservation.
[sin(
)
b)
N
Nx
z
Ra
SP
F
a
κα β ω
β
α κ
β κ κκ
=−
< >= = ×
+
1
2
0
( 0)
] e [sinh( ) ] (8)M
a N
Ma a a Rγβ γ γ
γ
−
−
=−≠
+ +
∑ ��� � �
���
5. Numerical Examples for Post-Wall Waveguides
0
/ 2.33 2.0 0.4 7.2 Posts: perfect conductor
s
h mmr mma mm
ε ε ====
Parameters
a
h2r
ε µ0,s
z
x
V. Jandieri, H. Maeda, K. Yasumoto and D. Erni, “Analysis of Post-Wall Waveguides and Circuits Using a Model of Two-Dimensional Photonic Crystals,” Progress in Electromagnetics Research M (PIER M), vol.56 pp. 91-100, 2017.
K. Yasumoto, H. Maeda and V. Jandieri, “Analysis of Post-Wall Waveguides Using a Model of Two-Dimensional Photonic Crystal Waveguides,“ Proceedings of the IEEE International Conference on Signal Processing and Communication (ICSC-2015), Noida, India, pp. 74-79, April, 2015 (Invited Paper)
.(3) .(1)For 1- layer structure, the difference between is less than0.09%.
Eq Eqβ β−
100 : transmission coefficient, 2.0 , 0.4 , 7.2 F h mm r mm a mm= = =
2 2 2 20
0( ( / ))e s s e
e
a k k a
aπ κ β β πκ
⇒= − = −=
Effective width of equivalent rectangular waveguide
V. Jandieri, H. Maeda, K. Yasumoto and D. Erni, “Analysis of Post-Wall Waveguides and Circuits Using a Model of Two-Dimensional Photonic Crystals,”Progress in Electromagnetics Research M (PIER M), vol.56 pp. 91-100, 2017.
K. Yasumoto, H. Maeda and V. Jandieri, “Analysis of Post-Wall Waveguides Using a Model of Two-Dimensional Photonic Crystal Waveguides,“ Proceedings of the IEEE International Conference on Signal Processing and Communication (ICSC-2015), Noida, India, pp. 74-79, April, 2015 (Invited Paper)
[6] D. Deslandes and K. Wu, “Accurate modeling, wave mechanisms, and design considerations of a substrate integrated waveguide,” IEEE Trans. Microwave Theory Tech., vol. 54, no. 6, pp. 2516-2526, 2006.
000 0
0
2
0 00
1
2
0 0 00
( 0)
ln ( , )
0.5
(7)
[sin( ) ] e [sinh( ) ] (8)
N
Nx
z
Ma N
M
Ra
SP
F
a a a a Rγ
κα β ω
β
α κ
ββ κ κ γ γκ γ
−
−
=−≠
=−
< >= = ×
+ + +
∑ ��� � �
���
Attenuation constant calculated using (7) and (8)plotted by the dashed-dotted line and dashed line,respectively, is compared with Ref. [6] representedby the solid line.
V. Jandieri, H. Maeda, K. Yasumoto and D. Erni, “Analysis of Post-Wall Waveguides and Circuits Using a Model of Two-Dimensional Photonic Crystals,” Progress in Electromagnetics Research M (PIER M), vol.56 pp. 91-100, 2017.
K. Yasumoto, H. Maeda and V. Jandieri, “Analysis of Post-Wall Waveguides Using a Model of Two-Dimensional Photonic Crystal Waveguides,“ Proceedings of the IEEE International Conference on Signal Processing and Communication (ICSC-2015), Noida, India, pp. 74-79, April, 2015 (Invited Paper)
6. Numerical Examples for Compact Circuits
Bandpass filter with three circular posts of conductor: (a) Original post-wall waveguidestructure; (b) Equivalent rectangular waveguide structure, and (c) S-parameters of the circuit (a).
Theory of Images
Bandpass filter with three circular posts of conductor: (a) Original post-wall waveguidestructure; (b) Equivalent rectangular waveguide structure, and (c) S-parameters of the circuit (a).
Bandpass filter with three circular posts of conductor: (a) Original post-wall waveguidestructure; (b) Equivalent rectangular waveguide structure, and (c) S-parameters of the circuit (a).
Bandpass filter with three circular posts of conductor: (a) Original post-wall waveguidestructure; (b) Equivalent rectangular waveguide structure, and (c) S-parameters of the circuit (a).
Remarks on PWWs Formed by Dielectric Posts
Which is preferable as the material of posts, a metal (PEC) or a dielectric?
Can the equivalent rectangular waveguide model with the effective width ae be defined for a PWW formed by dielectric posts?
When designing PWW devices, we should bear in mind the difference in wave propagation between PWWs of a metal (PEC) and PWWs of a dielectric near the cutoffs.
Reflection
Leakage
Leakage
Cutoff in a rectangular waveguideCutoff in a post-wall waveguide
with metallic posts
••
Cutoff in a dielectric waveguideCutoff in a post-wall waveguide
with dielectric posts
••
Two different mechanisms of waveguide cutoff
7. Conclusions
A photonic crystal waveguide model for post-wall waveguides has been proposed.A simplified dispersion equation of post-wall waveguides based
on the long wavelengths approximation has been presente
•
•d.
Using the dispersion equation, the propagation constants and effective width of post-wall waveguides can be easily and accurately calculated.The long wavelengths approximation, which is valid w
•
• hen only the fundametal Floquet mode is propagating, can be applicable to various post-wall waveguide geometries reported in literatures.Compact circuits - bandpass filters - have been accurately a• nalyzed.