Mobile Radio Propagation Channel Models
Mobile Radio PropagationChannel Models
WITS Lab, NSYSU.2
Table of Contents
IntroductionPropagation Path Loss Model
Friis Free Space ModelHata Model
Large Scale Propagation ModelLognormal Distribution
Small scale Propagation ModelMultipath
Delay Spread vs. Coherent BandwidthFlat Fading vs. Frequency Selective FadingNarrowband vs. Wideband
WITS Lab, NSYSU.3
Table of ContentsDoppler’s Effect
Doppler’s Shift vs. Coherent TimeFast Fading vs. Slow Fading.
Rayleigh DistributionLevel Crossing Rate
Ricean DistributionComputer Simulation of Multipath InterferenceChannel Models in WCDMAFading Counteraction – Diversity SchemesDownlink Transmit Diversity in WCDMA
Introduction
WITS Lab, NSYSU.5
Main Components of Radio Propagation
Propagation Path Loss. ( ~ 1/r2 in free space)Large Scale: Propagation models that predict the strength for an arbitrary separation distance.Small Scale: Propagation models that characterize the rapid fluctuation of the received signal strength over very short travel distance (~λ ) or short time duration (~s).
WITS Lab, NSYSU.6
Large-Scale Propagation ModelsPropagation models that predict the mean signal strength for an arbitrary transmitter-receiver (T-R) separation distance are useful in estimating the radio coverage area of a transmitter.
They characterize signal strength over large T-R (transmitter – receiver) separation distances (several hundreds or thousands of meters).
WITS Lab, NSYSU.7
Small-Scale Propagation ModelsSmall-scale fading is used to describe the rapid fluctuation of the amplitude of a radio signal over a short period of time or travel distance.Fading is caused by interference between two or more versions of the transmitted signal which arrive at the receiver at slightly different time.These waves, called multi-path waves, combine at the receiver antenna to give a resultant signal which can vary widely in amplitude and phase.
WITS Lab, NSYSU.8
Small-Scale Propagation Models
The received signal power may vary by as much as three or four orders of magnitude (30 or 40 dB) when the receiver is moved by only a fraction of a wavelength.Typically, the local average received power is computed by averaging signal measurements over a measurement track of 5λ to 40 λ.
Hint : with f = 1 GHz ~ 2 GHz,
cmcmfc 15~30==λ
WITS Lab, NSYSU.9
Small-Scale vs. Large-Scale Fading
Propagation Path Loss Model
WITS Lab, NSYSU.11
Free Space Propagation Model
The free space propagation model is used to predict received signal strength when the transmitter and receiver have a clear, unobstructed line-of-sight (LOS)path between them.
e.g. satellite, microwave ling-of-sight radio link.
As with most large-scale radio wave propagation models, the free space model predicts that received power decays as a function of the T-R separation distance raised to some power.
WITS Lab, NSYSU.12
Friis Free Space Equation
meters.in h wavelengt the:n.propagatio torelatednot factor loss system the:
meters.in distance separation R-T the:gain. antennareceiver the:
gain. antennaer transmitt the:.separation R-T
theoffunction a ish power whic received :)(power. ed transmitt:
)4()( 22
2
λ
πλ
LdGG
dPP
LdGGPdP
r
t
r
t
rttr =
WITS Lab, NSYSU.13
The gain of an antenna is related to its effective aperture, Ae, by:
The effective aperture Ae is related to the physical size of the antenna.The miscellaneous losses L (L≥1) are usually due to transmission line attenuation , filter losses, and antenna losses in the communication system.L=1 indicates no loss in the system hardware.
Friis Free Space Equation
2
4λπ eAG =
WITS Lab, NSYSU.14
Log-distance Path Loss Model
( )0
ndPL dd
⎛ ⎞∝ ⎜ ⎟
⎝ ⎠
( ) ( )00
dB 10 log dPL PL d nd
⎛ ⎞= + ⎜ ⎟
⎝ ⎠
WITS Lab, NSYSU.15
Hata Model
An empirical formulation of the graphical path loss data provided by OkumuraValid from 150M to 1500Mhz.hte : 30m ~ 200m (base station antenna height)hre : 1m~10m (mobile antenna height)d : T-R separation distance (in km)a (hre) : correction factor for effective mobile antenna height.
dhhahfdburbanL
terete
c
log)log55.69.44()(log82.13log16.2655.69))((50
−+−−+=
WITS Lab, NSYSU.16
Hata Model
For small to medium sized city:
For large city:
For suburban area:
For open rural areas:
dBfhfha crecre )8.0log56.1()7.0log1.1()( −−−=
2
2
( ) 8.29(log1.54 ) 1.1 for 300
( ) 3.2(log11.75 ) 4.97 for 300re re c
re re c
a h h dB f MHz
a h h dB f MHz
= − ≤
= − ≥
4.5)]28/[log(2)()( 25050 −−= cfurbanLdbL
98.40log33.18)(log78.4)()( 25050 −−−= cc ffurbanLdbL
WITS Lab, NSYSU.17
Hata Model in PCS BandExtension of Hata model to 2 GHz.
Mtere
tec
CdhhahfdburbanL
+−+−−+=
10
50
log)log55.69.44()(log82.13log9.333.46))((
centersan metropolitfor 3dB areassuburban andcity sized mediumfor 0dB
==MC
kmkmdmmh
mmhMHzMHzf
re
te
20~1:10~1:
200~30:2000~1500:
Large Scale Propagation Model
WITS Lab, NSYSU.19
Shadowing Effect – Lognormal DistributionWhen reaching the mobile station, the radio wave will have traveled through different obstructions such as buildings, tunnels, hills, trees, etc.The received signal R, when measured in decibels, has a normal density function. Thus R is described by lognormal distribution.
The PDF of R is:
Xσ: a zero-mean Gaussian distributed random variable (dB) with standard deviation 4 - 10 dB.
( ) ( ) ( ) σσ XddndPLXdPLdPL +⎟⎟
⎠
⎞⎜⎜⎝
⎛⋅⋅+=+=
00 log10
( )( ) ( )
( )
2 2ln / 21 02
0 0
r me rp r r
r
σ
πσ− −⎧ ≥⎪= ⎨
⎪ <⎩
WITS Lab, NSYSU.20
Correlation of Path Loss
Shadow Fading:
Correlation of Path Loss: (from Viterbi, Principles of Spread Spectrum Communications)
1010ζ∝nattenuatio
2 2
2
1,
( ) ( ) ( ) 0,
( ) ( ) ( ) .
mobile base station
mobile base station
mobile base station
a b
a b
E E E
Var Var Var
ζ ξ ξ
ζ ξ ξ
ζ ξ ξ σ
−
−
−
= ⋅ + ⋅
+ =
= = =
= = =
Small Scale Propagation Model
WITS Lab, NSYSU.22
Small Scale Fading -- 1Problem 1: multi-path induces delay spread.
WITS Lab, NSYSU.23
Impulse Response Model of a MultipathChannel
A mobile radio channel may be modeled as a linear filter with a time varying impulse response, where the time variation is due to receiver motion in space.The filtering nature of the channel is caused by the summation of amplitudes and delays of the multiple arriving waves at any instant of time.
WITS Lab, NSYSU.24
Channel Impulse ResponseDue to the different multipath waves which have propagation delays which vary over different spatial locations of the receiver, the impulse response of the linear time invariant channel shouldbe a function of the position of the receiver.
( , ) ( ) ( , ) ( ) ( , )
where ( , ) is the channel impulse resonse. ( ) is the transmitted signal. ( , ) is the received signal at position .
y d t x t h d t x h d t d
h d tx ty d t d
τ τ τ∞
−∞
= ⊗ = −∫
WITS Lab, NSYSU.25
Multipath Radio Channel
WITS Lab, NSYSU.26
Multipath Propagation Effect
WITS Lab, NSYSU.27
Measured Multipath Power Delay Profiles
From a 900 MHz cellular system in San Fancisco.
WITS Lab, NSYSU.28
Measured Multipath Power Delay Profiles
Inside a grocery store at 4 GHz.
WITS Lab, NSYSU.29
Delay SpreadDelay spread and coherence bandwidth are used to describe the time dispersive nature of the channel.Received Signal:
Delay Spread corresponds to standard deviation of Ti .
Excess delay is the relative delay of the i-th multipathcomponent as compared to the first arriving component.
)()(1
∑=
−=n
i
ii Ttath δ
τσ
WITS Lab, NSYSU.30
Time Dispersion Parameters
Mean Excess Delay: the first moment of the power delay profile.
RMS (room mean square) Delay Spread: the square root of the second central moment of the power delay profile.
∑∑
∑∑
==
kk
kkk
kk
kkk
P
P
a
a
)(
)(
2
2
τ
ττττ
22 )(ττσ τ −=
∑∑
∑∑
==
kk
kkk
kk
kkk
P
P
a
a
)(
)( 2
2
22
2
τ
ττττ
WITS Lab, NSYSU.31
Time Dispersion Parameters
These delays are measured relative to the first detectable signal arriving at the receiver at τ0=0.The equations in the previous page do not rely on the absolute power level of P(τ), but only the relative amplitudes of the multipath components within P(τ).Typical values of rms delay spread are on the order of microseconds in outdoor mobile radio channels and on the order of nanoseconcds in indoor radio channels.
WITS Lab, NSYSU.32
Typical Measured Values of RMS Delay Spread
WITS Lab, NSYSU.33
Maximum Excess DelayMaximum Excess Delay (ΧdB) = the time delay during which multipath energy falls to ΧdB below maximum.Maximum Excess Delay (ΧdB) can also be defined as τx-τ0, where τ0 is the first arriving signal; τx is the maximum delay at which a multipath component is within X dB of the strongest arriving multipath signal.The value of τx is sometimes called the excess delay spread of a power delay profile.
WITS Lab, NSYSU.34
Example of An Indoor Power Delay Profile
WITS Lab, NSYSU.35
Coherence BandwidthTime domain focus on excess delay.Frequency domain focus on coherence bandwidth Bc.Bc is defined related to rms delay spread ∝ 1/(Bc)Bc (Coherence Bandwidth)
A statistical measure of the range of frequencies over which the channel can be considered flat (i.e. a channel which passes all spectral components with approximately equal gain and linear phase.).The range of frequencies over which two frequency components have a strong potential for amplitude correlation.Two sinusoids with frequency separation greater than Bc are affected quite differently by the channel.
WITS Lab, NSYSU.36
Coherence BandwidthVersion 1: the bandwidth over which the frequency correlation is above 0.9
Version 2: the bandwidth over which the frequency correlation is above 0.5
150cB
τσ=
15cB
τσ=
WITS Lab, NSYSU.37
Types of Small-Scale Fading
Based on multi-path time delay spread
Flat Fading (narrowband system)BW of signal < BW of channelDelay spread < Symbol period
Frequency Selective Fading (wideband system)BW of signal > BW of channelDelay spread > Symbol period
WITS Lab, NSYSU.38
Wideband v.s. Narrowband
f f
t1
t2Signal Bandwidth
wideband narrow band
Signal Bandwidth
WITS Lab, NSYSU.39
Flat Fading
Signal undergoes flat fading if CS BB << and τσ>>STTs : reciprocal BW (e.g. symbol period)Bs : BW of the TX modulationστ : rms delay spread Bc : Coherence BW
WITS Lab, NSYSU.40
Flat Fading
The mobile radio channel has a constant gain and linear phase response over a bandwidth which is greater than the bandwidth of the transmitted signal.The multipath structure of the channel is such that the spectral characteristics of the transmitted signal are preserved at the receiver.The strength of the received signal changes with time, due to fluctuations in the gain of the channel caused by multipath.
WITS Lab, NSYSU.41
Flat Fading
Typical flat fading channels cause deep fades, and thus may require 20 or 30 dB more transmitter power to achieve low bit error rates during times of deep fades as compared to systems operating over non-fading channels.Also known as amplitude varying channel.Also referred to as narrowband channels since the bandwidth of the applied signal is narrow as compared to the channel flat fading bandwidth.The most common amplitude distribution of flat fading channel is the Rayleigh distribution.
WITS Lab, NSYSU.42
Frequency Selective Fading
Signal undergoes frequency selective fading if CS BB > and τσ<ST
WITS Lab, NSYSU.43
Frequency Selective FadingThe channel possesses a constant-gain and linear phase response over a bandwidth that is smaller than the bandwidth of transmitted signal.The received signal includes multiple versions of the transmitted waveform which are attenuated and delayed in time.The channel induces inter-symbol interference.Certain frequency components in the received signal spectrum have greater gains than others.Also known as wideband channels.M-ray Rayleigh fading model is usually used for analyzing frequency selective small-scale fading.
WITS Lab, NSYSU.44
Small Scale Fading -- 2Problem 2: moving receiver induces fading effects (Doppler shift) for each ray path.
WITS Lab, NSYSU.45
Doppler Effect
Doppler is a frequency shift, cause by movement of the mobile antenna relative to the base station- Δf = V/λ (at 250 km/h and 900 MHz, Δf = 208 Hz)
V
f
f + ∆ff - ∆f
WITS Lab, NSYSU.46
Doppler Shift / Spread
θθ coscos tvdl ∆==∆
θλ
πλπφ cos22 :Change Phase tvl ∆
=∆
=∆
θλ
φπ
cos21 :ShiftDoppler v
tfd =
∆∆
⋅=
WITS Lab, NSYSU.47
Doppler Spread and Coherence Time
Delay spread and coherence bandwidth do not offer information about the time varying nature of the channel caused by either relative motion between the mobile and base station, of by movement of objects in the channel.Doppler spread and coherence time are parameters which describe the time varying nature of the channel in a small-scale.Doppler spread BD is a measure of the spectral broadening caused by the time rate of change of the mobile radio channel and is defined as the range of frequencies over which the received Doppler spectrum is essentially non-zero.When a pure sinusoidal tone of frequency fc is transmitted, the received signal spectrum, called the Doppler spectrum, will be in the range fc-fd to fc+fd , where fd is Doppler shift.
WITS Lab, NSYSU.48
Coherence Time
Coherence time Tc is the time domain dual of Doppler spread and is used to characterize the time varying nature of the frequency dispersiveness of the channel in the time domain.Coherence time is a statistical measure of the time duration over which the channel impulse response is essentially invariant.Coherence time is the time duration over which two received signals have a strong potential for amplitude correlation.
WITS Lab, NSYSU.49
Coherence TimeVersion 1:ƒm : the maximum Doppler shift, ƒm = ν/λ
Version 2: the time over which the time correlation > 0.5
Version 3: Geometric mean of version 1 and version 2.
mc fT 1≈
mc fT π169≈
mmc ff
T 423.016
92 ==
π
WITS Lab, NSYSU.50
Doppler Power Spectrum
WITS Lab, NSYSU.51
Types of Small-Scale FadingBased on Doppler Spread
Fast FadingHigh Doppler spread.Coherence time < Symbol Period.Channel variations faster than base-band signal variations
Slow FadingLow Doppler spread.Coherence time > Symbol period.Channel variations slower than base-band signal variations
WITS Lab, NSYSU.52
Fast FadingTS>TC and BS<BD.The channel impulse response changes rapidly within the symbol duration.The coherence time of the channel is smaller than the symbol period of the transmitted signal.Signal distortion due to fast fading increases with increasing Doppler spread relative to the bandwidth of the transmitted signal.Fast fading only deals with the rate of change of the channel due to motion.In practice, fast fading only occurs for very low data rates (or very fast motion speed).
WITS Lab, NSYSU.53
Slow Fading
TS<<TC and BS>>BDChannel impulse response changes at a rate much slower than the transmitted baseband signal s(t).The channel may be assumed to be static over one or several reciprocal bandwidth intervals.The Doppler spread of the channel is much less than the bandwidth of the baseband signal.The velocity of the mobile and the basebandsignaling determines whether a signal undergoes fast fading or slow fading.
WITS Lab, NSYSU.54
Type of Small-Scale Fading
WITS Lab, NSYSU.55
Type of Small-Scale Fading
Rayleigh Distribution
WITS Lab, NSYSU.57
Rayleigh Distribution
Rayleigh distributions are commonly used to describe the statistical time varying nature of the received envelope of a flat fading signal, or the envelope of an individual multipath component.
Envelope of the sum of two quadrature Gaussian noise signals obeys a Rayleigh distribution.
WITS Lab, NSYSU.58
Typical Rayleigh Fading Envelope
WITS Lab, NSYSU.59
Rayleigh DistributionConsider a carrier signal s at a frequency ω0 and with an amplitude a:
The received signal sr is the sum of n waves:
)exp( 0tjas ω⋅=
[ ] [ ]
θθ
θθ
θθθ
θθ
θωθω
sin cos :where
sin and cos :have We
sincos)exp( :Define
)exp()exp( where
)(exp)(exp
22211
11
1
01
0
ryrxyxr
ayax
jyxajajr
jajr
tjrtjas
n
iii
n
iii
n
iii
n
iii
n
iii
n
iiir
==+=
≡≡
+≡+=
=
+≡+=
∑∑
∑∑
∑
∑
==
==
=
=
WITS Lab, NSYSU.60
Rayleigh DistributionBecause (1) n is usually very large, (2) the individual amplitudes ai are random, and (3) the phases θi have a uniform distribution, it can be assumed that (from the central limit theorem) x and yare both Gaussian variables with means equal to zero and variance
Because x and y are independent random variables, the joint distribution p(x,y) is
The distribution p(r,θ) can be written as a function of p(x,y) :
222 σσσ ≡= yx
⎟⎟⎠
⎞⎜⎜⎝
⎛ +−== 2
22
2 2exp
21)()(),(
σπσyxypxpyxp
),(),( yxpJrp =θ
WITS Lab, NSYSU.61
Rayleigh Distribution
The probability that the envelope of the received signal does not exceed a specified value R is given by the corresponding cumulative distribution function (CDF)
2
2
22
2 2
0
/ / cos sin; ( , ) exp
/ / sin cos 2 2Thus, the Rayleigh distribution has a pdf:
exp 0 ( ) ( , ) 2
0 ot
x r x r r rJ r p ry r y r
r r rp r p r d
π
θ θ θθ
θ θ θ πσ σ
θ θ σ σ
∂ ∂ ∂ ∂ − ⎛ ⎞≡ = = = −⎜ ⎟∂ ∂ ∂ ∂ ⎝ ⎠
⎛ ⎞− ≥⎜ ⎟= = ⎝ ⎠∫
herwise
⎧⎪⎨⎪⎩
⎟⎟⎠
⎞⎜⎜⎝
⎛−−==≤= ∫ 2
2
0 2exp1)()Pr()(
σRdrrpRrRP
R
WITS Lab, NSYSU.62
Rayleigh DistributionMean:
Variance:
Median value of r is found by solving:
Mean squared value:
Most likely value = max { p(r) } = σ
σπσ 2533.12
)(][0
==== ∫∞
drrrprErmean
22
2
0
2222
4292.02
2
2)(][][
σπσ
πσσ
=⎟⎠⎞
⎜⎝⎛ −=
−=−= ∫∞
drrprrErEr
∫=medianr
drrp0
)(21
σ177.1=medianr
∫∞
==0
222 2)(][ σdrrprrE
WITS Lab, NSYSU.63
Rayleigh Probability Density Function
WITS Lab, NSYSU.64
Level Crossing and Fading Statistics
The level crossing rate (LCR) is defined as the expected rate at which the Rayleigh fading envelope, normalized to the local rms signal level, crosses a specified level in a positive-going direction.
Useful for designing error control codes and diversity.Relate the time rate of change of the received signal to the signal level and velocity of the mobile.
WITS Lab, NSYSU.65
Level Crossing Rate (LCR)
The number of level crossings per second is given by:2
0
( , ) 2
is the tim e derivative of ( ) (i.e. the slope)
( , ) is the joint density function of and at is the m axim um D oppler frequency
/ is the value of the sp
R m
m
rm s
N r p R r d r f e
r r t
p R r r r r Rf
R R
ρπ ρ
ρ
∞ • • •−
•
• •
= =
=
=
∫
ecified level , norm alized to the local rm s am plitude of the fading envelope.
R
Clarke, R. H., “A Statistical Theory of Mobile-Radio Reception,”Bell Systems Technical Journal, Vol. 47, pp. 957-1000, 1968.
WITS Lab, NSYSU.66
Average Fade DurationAverage fade duration is defined as the average period of time for which the received signal is below a specified level R. For a Rayleigh fading signal, this is given by:
where Pr[r≤R] is the probability that the received signal r is less than R and is given by
where τi is the duration of the fade and T is the observation interval of the fading signal.
[ ]1 PrR
r RN
τ = ≤
[ ] 1Pr ii
r RT
τ≤ = ∑
WITS Lab, NSYSU.67
Average Fade DurationThe probability that the received signal r is less than the threshold R is found fro the Rayleigh distribution as:
where p(r) is the pdf of a Rayleigh distribution.The average fade duration as a function of ρ and fm can be expressed as
)exp(1)(]Pr[ 2
0
ρ−−==≤ ∫R
drrpRr2
22
2σρ R
=
2
12m
ef
ρ
τρ π
−=
WITS Lab, NSYSU.68
Average Fade DurationThe average duration of a signal fade helps determine the most likely number of signaling bits that may be lost during a fade.
Average fade duration primarily depends upon the speed of the mobile, and decreases as the maximum Doppler frequency fm becomes large.
Ricean Distribution
WITS Lab, NSYSU.70
Ricean Fading Distribution
When there is a dominant stationary (non-fading) signal component present, such as a line-of-sight propagation path, the small-scale fading envelope distribution is Ricean.
θθ
θωωωθω
sincos
)(
)](exp[)exp(])[( )exp()](exp['
22200
esdirect wav
0
wavesscattered
0
ryrAx
yAxr
tjrtjjyAxtjAtjrsr
==+
++=
+≡++≡++=
WITS Lab, NSYSU.71
Ricean Fading DistributionBy following similar steps described in Rayleigh distribution, we obtain:
( )
∑
∫
∞
=⎟⎟⎠
⎞⎜⎜⎝
⎛⋅
=
⎟⎟⎠
⎞⎜⎜⎝
⎛=⎟⎟
⎠
⎞⎜⎜⎝
⎛
⎪⎩
⎪⎨⎧
<
≥≥⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛ +−=
00
2
0220
202
22
2
2!
function. Besselorder -zeroth modified theis
cosexp21
where0for 0
0r0,Afor 2
exp)(
ii
i
rr
rrr
ix(x)I
dArArI
)(r
ArIArrrp
θσ
θπσ
σσσ
π
WITS Lab, NSYSU.72
Ricean Fading DistributionThe Ricean distribution is often described in terms of a parameter K which is defined as the ratio between the deterministic signal power and the variance of the multipath. It is given by K=A2/(2σ2) or in terms of dB:
The parameter K is known as the Ricean factor and completely specifies the Ricean distribution.As A 0, K -∞ dB, and as the dominant path decreases in amplitude, the Ricean distribution degenerates to a Rayleighdistribution.
2
2( ) 10 log [dB]2AK dBσ
= ⋅
WITS Lab, NSYSU.73
Ricean Fading Distribution
Computer Simulation of Multi-path Interference
Reference: “Microwave Mobile Communications”,by W.C. Jakes, pp. 60-71.
WITS Lab, NSYSU.75
Frequency Selective Fading ChannelRayleigh fading is usually adopted for flat fading channel model.Frequency selective fading channel model is usually modeled as the sum of several flat fading channels with different delays.
t0
t1
tn-1
Rayleigh
Rayleigh
Rayleigh
∑
WITS Lab, NSYSU.76
Spatial Correlations at the Base Station
Scattering model for spatial correlations at the base station.
WITS Lab, NSYSU.77
Computer Simulation of Rayleigh Fading
Simulator that duplicates mobile radio spectrumProducing random phase modulation, a Rayleigh fading envelope, and a time-averaged, discrete approximation to the desired power spectrum.Simulation inputs:
Carrier frequency.Mobile velocity.Sampling rate.
The number of frequency components (N0) needed is at least 8 (N is at least 34 where N0 =0.5*(N/2-1) and N/2 is an odd integer).
WITS Lab, NSYSU.78
Computer Simulation of Rayleigh FadingSimulator that duplicates mobile radio spectrum
Channel Models in WCDMA
WITS Lab, NSYSU.80
(I) Static Propagation ConditionThe propagation for the static performance measurement is an Additive White Gaussian Noise (AWGN) environment. No fading or multi-paths exist for this propagation model.
WITS Lab, NSYSU.81
(II) Multi-Path Fading Propagation Conditions
Table B.1 shows propagation conditions that are used for the performance measurements in multi-path fading environment. All taps have classical Doppler spectrum, defined as: ( )
( )2
1 [ , ]1
D D
D
S f f f ff f
∝ ∈ −−
Table B.1: Propagation Conditions for Multi path Fading Environments
-9781-9781
-6521-6521020000
-3260-32600976-10976
00000000
Average Power [dB]
Relative Delay [ns]
Average Power [dB]
Relative Delay [ns]
Average Power [dB]
Relative Delay [ns]
Average Power [dB]
Relative Delay [ns]
Case 4, 250 km/hCase 3, 120 km/hCase 2, speed 3 km/hCase 1, speed 3km/h
WITS Lab, NSYSU.82
(III) Moving Propagation Conditions
The dynamic propagation conditions for the test of the base band performance are non-fading channel models with two taps. The moving propagation condition has two tap, one static, Path0, and one moving, Path1. The time difference between the two paths is according Equation (B.1). The parameters for the equation are shown in Table B.2. The taps have equal strengths and equal phases.
t 1
P 1
∆ τ
P 0
t 0
Table B.2: Parameters for moving propagation
40⋅10-3 s-1Δω
1 µsB
5 µsA
Figure B.1: The moving propagation conditions
( ))sin(12
tAB ⋅∆++=∆ ωτ (B.1)
WITS Lab, NSYSU.83
(IV) Birth-Death Propagation Conditions
The dynamic propagation conditions for the test of the basebandperformance is a non-fading propagation channel with two taps. The moving propagation conditions has two taps, Path1 and Path2 which alternate between 'birth' and 'death'. The positions the paths appear are randomly selected with an equal probability rate and are shown in Figure B.2.
0 1 2 3 4 5-1-2-3-4-5 0 1 2 3 4 5-1-2-3-4-5 0 1 2 3 4 5-1-2-3-4-5
P1 P2 P1 P1 P2 P1P2 P2
Figure B.2: Birth death propagation sequence
WITS Lab, NSYSU.84
Birth-Death Propagation Conditions
1. Two paths, Path1 and Path2 are randomly selected from the group [-5, -4, -3, -2, -1, 0 ,1, 2, 3, 4, 5] µs. The paths have equal magnitudes and equal phases.
2. After 191 ms, Path1 vanishes and reappears immediately at a new location randomly selected from the group [-5, -4, -3, -2, -1, 0 ,1, 2, 3, 4, 5] µs but excludes the point Path2. The magnitudes and the phases of the tap coefficients of Path 1 and Path 2 shall remain unaltered.
3. After an additional 191 ms, Path2 vanishes and reappears immediately at a new location randomly selected from the group [-5, -4, -3, -2, -1, 0 ,1, 2, 3, 4, 5] µs but excludes the point Path1. The magnitudes and the phases of the tap coefficients of Path 1 and Path 2 shall remain unaltered.
4. The sequence in 2) and 3) is repeated.
Fading Counteraction – Diversity Schemes
WITS Lab, NSYSU.86
Fading CounteractionsLong-Term (large scale) Fading Counteraction: Macroscopic diversity (Space diversity)
S-diversityS+I-diversityS/I-diversity
WITS Lab, NSYSU.87
Fading CounteractionShort-Term (small scale) Fading Counteraction: Microscopic diversity.
Space diversity - spacing is between receiving antennas.Polarization: orthogonality of the polarized wave components.Angle: directional antenna.Frequency: two or more different carriers.Time: time separation.Hopping: frequency hopping and time hopping.
WITS Lab, NSYSU.88
Combining SchemesSwitched Combining
Pure Selection: the received signals are continuously monitored so that the best signal can be selected.Threshold Selection: the received signals are scanned in a sequential order, and the first signal with a power level above a certain threshold is selected.
Gain CombiningMaximal Ratio Combining (MRC): each one of the M signals has a gain proportional to its own signal-to-noise ratio.Equal Gain Combining: all of the signals have a gain equal to one.
Downlink Transmit Diversity in WCDMA
WITS Lab, NSYSU.90
Downlink Transmit Diversity in WCDMA
OO-DL-DPCCH for CPCH
-O-CD/CA-ICH
-O-AP-AICH
–O–CSICH
–O–AICH
OO–PDSCH
–O–PICH
OO–DPCH
–O–S-CCPCH
––OSCH
–O–P-CCPCH
ModeSTTDTSTD
Closed loopOpen loop modePhysical channel type
Application of Tx diversity modes on downlink physical channel types“O” : can be applied, “–” : not applied
Simultaneous use of STTD and closed loop modes on the same physical channel is not allowed.
WITS Lab, NSYSU.91
Space Time Transmit Diversity (STTD)
The STTD encoding is optional in UTRAN. STTD support is mandatory at the UE.
b0 b1 b2 b3
b0 b1 b2 b3
-b2 b3 b0 -b1
Antenna 1
Antenna 2Channel bits
STTD encoded channel bitsfor antenna 1 and antenna 2.
WITS Lab, NSYSU.92
Time Switched Transmit Diversity
PrimarySCH
SecondarySCH
256 chips
2560 chips
One 10 ms SCH radio frame
acsi,0
acp
acsi,1
acp
acsi,14
acp
Slot #0 Slot #1 Slot #14
Structure of Synchronisation Channel (SCH)
WITS Lab, NSYSU.93
Time Switched Transmit Diversity
Antenna 1
Antenna 2
acsi,0
acp
acsi,1
acp
acsi,14
acp
Slot #0 Slot #1 Slot #14
acsi,2
acp
Slot #2
(Tx OFF)
(Tx OFF)
(Tx OFF)
(Tx OFF)
(Tx OFF)
(Tx OFF)
(Tx OFF)
(Tx OFF)
Structure of SCH transmitted by TSTD scheme
WITS Lab, NSYSU.94
Downlink Transmitter Structure to Support Closed Loop Mode Transmit Diversity for DPCH Transmission
Spread/scramblew1
w2
DPCHDPCCH
DPDCH
∑
CPICH1
∑
CPICH2
Ant1
Ant2
Weight Generation
w1 w2
Determine FBI messagefrom Uplink DPCCH