Mini Hi-Fi System FW-M567 FW-M567 visit our website www.audio.philips.com to download latest UPDATES of USB PC Link Driver MusicMatch Jukebox softwares and FAQs.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Mini Hi-Fi System FW-M567FW-M567
visit our website
www.audio.philips.comto download latest UPDATES of USB PC Link Driver
MusicMatch Jukebox softwares and FAQs.
2
Important notes for users in theU.K.
Mains plugThis apparatus is fitted with an approved 13Amp plug. To change a fuse in this type of plugproceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socketoutlets, it should be cut off and an appropriateplug fitted in its place.If the mains plug contains a fuse, this shouldhave a value of 5 Amp. If a plug without a fuseis used, the fuse at the distribution boardshould not be greater than 5 Amp.
Note: The severed plug must be disposed of toavoid a possible shock hazard should it beinserted into a 13 Amp socket elsewhere.
How to connect a plugThe wires in the mains lead are coloured withthe following code: blue = neutral (N),brown = live (L).
¶ As these colours may not correspond with thecolour markings identifying the terminals inyour plug, proceed as follows:– Connect the blue wire to the terminalmarked N or coloured black.– Connect the brown wire to the terminalmarked L or coloured red.– Do not connect either wire to the earthterminal in the plug, marked E (or e) orcoloured green (or green and yellow).
Before replacing the plug cover, make certainthat the cord grip is clamped over the sheathof the lead - not simply over the two wires.
Copyright in the U.K.Recording and playback of material mayrequire consent. See Copyright Act 1956 andThe Performer’s Protection Acts 1958 to 1972.
NorgeTypeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundertinnkoplet. Den innebygde netdelen erderfor ikke frakoplet nettet så lengeapparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektriskstøt, skal apparatet ikke utsettes for regn ellerfuktighet.
ItaliaDICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio FW-M567, Philipsrisponde alle prescrizioni dell’art. 2 comma 1 delD.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer ElectronicsPhilips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
CAUTIONUse of controls or adjustments orperformance of procedures other thanherein may result in hazardousradiation exposure or other unsafeoperation.
VAROITUSMuiden kuin tässä esitettyjentoimintojen säädön tai asetustenmuutto saattaa altistaa vaarallisellesäteilylle tai muille vaarallisilletoiminnoille.
33
P3
DISC 5DISC 5
DISC 1DISC 1
DISC 2DISC 2
DISC 3DISC 3
DISC 4DISC 4
DISC DISC
3 DISC DISC
4 DISC DISC
5DISC DISC
2DISC DISC
1
CDCD/CD-RCD-R
/CD-RCD-R
W W COMPOMP
ATIBLETIBLE
STANDBYON
ECOPOWER
DIM
C D
PROG
IRIR
SENSOR
DSCDSCDBBDBB VAC
CLOCK •TIMER
TUNERTUNER GAME GAME•AUXUXUSBUSBPC LINKPC LINK
SPEED PUNCH BLASTMODEMODE
MIX-IT
GAMESOUNDGAMESOUND
MAMAX X SOUNDSOUND
MAX SOUND • DIGITAL SOUND CONTROL VIRTUAL AMBIENCE CONTROL • DYNAMIC BASS BOOST
A
UDIO
VIDEO
A
UDIO
GAME
VOLUM E
SEARCH• TUNING
PREV•PRESET
STO
P•
DEM
OST
OP
NEXT•PRESET
PLA
Y•
PAU
SE
GAME PORT MINI SYSTEM
RIGHT
LEFT
MASTER VOLUME
OVERDRIVE
TURBOTURBOCRUISE
LEFTCHA
NNEL
CD3
CD2
CD1
CD4
CD5ARCADE CINEMACONCERT
ALB MIX TITLEAM PMFM MWDIM SLEEPNEWSOPTIMAL JAZZ ROCK POP
TRKPROGSHUF REP DISC ALLCYBER HALLI.S.
DSCDSC
VAC
OVERDRIVE
TURBOTURBOCRUISE
RIGHT
CHANNEL
P2
REPEAT PROGRAM SHUFFLE DISPLAY
DSC MUTEVAC
GAME
DIM SLEEP CLK/TIMER TIMER
VOL
MAX ON/OFF
GAME
MIX-ITSOUND
ALBUM
TITLE
USB PC LINKCD TUNER AUX/GAME
ON/OFF
CD1 CD2 CD3
CD4 CD5
P1
P4
DISC 1DISC 1
DISC 2DISC 2
DISC 3DISC 3
DISC 4DISC 4
DISC DISC 3 DISC DISC 4 DISC DISC 5DISC DISC 2DISC DISC 1
CDCD /CD-RCD-R/CD-RW CD-RW COMPCOM PATIBLETIBLE
DISC 1DISC 1
1 3,
2
4
Energy StarAs an ENERGY STARR
Partner, Philips has determinedthat this product meets theENERGY STARR guidelines for energy efficiency.
DKAdvarsel: Usynlig laserstråling ved åbningnår sikkerhedsafbrydere er ude af funktion.Undgå utsættelse for stråling.
Bemærk: Netafbryderen er sekundærtindkoblet og ofbryder ikke strømmen franettet. Den indbyggede netdel er derfortilsluttet til lysnettet så længe netstikketsidder i stikkontakten.
SKlass 1 laseraparatVarning! Om apparaten används på annatsätt än i denna bruksanvisning specificerats,kan användaren utsättas för osynliglaserstrålning, som överskrider gränsen förlaserklass 1.
Observera! Stömbrytaren är sekundärtkopplad och bryter inte strömmen frånnätet. Den inbyggda nätdelen är därföransluten till elnätet så länge stickproppensitter i vägguttaget.
SFLuokan 1 laserlaite
Varoitus! Laitteen käyttäminenmuulla kuin tässä käyttöohjeessa mainitullatavalla saattaa altistaa käyttäjänturvallisuusluokan 1 ylittävällenäkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite eisaa olla alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytkettytoisiopuolelle, eikä se kytke laitetta irtisähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon ainasilloin, kun pistoke on pistorasiassa.
5
En
glis
hFr
ança
isP
ort
ugu
êsE
spañ
ol
Deu
tsch
Ned
erla
nds
Ital
ian
oS
ven
ska
Dan
skS
uo
mi
∂ÏÏ
ËÓÈ
οP
ols
ki
Index
English ------------------------------------------------ 6
Français -------------------------------------------- 28
Español --------------------------------------------- 50
Deutsch --------------------------------------------- 72
Nederlands ---------------------------------------- 94
Italiano -------------------------------------------- 116
Svenska ------------------------------------------- 138
Dansk --------------------------------------------- 160
Suomi --------------------------------------------- 182
Português ---------------------------------------- 204
----------------------------------------- 226
6
En
glish
Contents
General InformationSupplied accessories ............................................ 7Environmental information ................................ 7Care and safety information .............................. 7
Functional OverviewMain unit and remote control ....................... 8–9Control buttons available on theremote only ......................................................... 9
ConnectionsStep 1: Connecting FM/AM antennas ............. 11Step 2: Connecting the speakers .................... 11Step 3: Connecting to PC ................................. 11Step 4: Connecting to game console ............. 11Step 5: Connecting the AC power cord ........ 11Step 6: Inserting batteries into the remotecontrol .................................................................. 12Using the remote control to operatethe system ......................................................... 12
Gameport OperationsAbout Gameport ............................................... 13Preparation before use ..................................... 13Start operating .................................................... 13
USB PC LinkQuick Setup Guide ............................................ 14PC system requirement .................................. 14Install MusicMatch software .......................... 14Enable digital CD audio output .................... 15
Connecting USB PC Link ................................. 15
Basic OperationsSwitching on/off .................................................. 16Switching to active mode ............................... 16Switching to Eco Power standby mode ...... 16Switching to standby mode (view clock) .... 16
Demonstration mode ........................................ 16Setting the clock ................................................. 16Dimming system’s display screen .................... 17Volume control ................................................... 17Sound control ..................................................... 17MAX sound ....................................................... 17Digital Sound Control ..................................... 17Virtual Ambience Control ............................. 17Dynamic Bass Boost ........................................ 17
Disc OperationsPlayable discs ....................................................... 18Loading discs ....................................................... 18Basic playback controls ..................................... 18Playing an MP3 disc ............................................ 19Repeat and Shuffle .............................................. 19Repeat play ........................................................ 19Random play ...................................................... 19
Programming the disc tracks ........................... 20Checking the programme .............................. 20Clearing the programme ................................ 20
Tuner OperationsTuning to radio stations .................................... 21Presetting radio stations ................................... 21Using the Plug and Play ................................... 21Automatic presetting ...................................... 21Manual presetting ............................................. 21
Selecting a preset radio station ....................... 22Deleting a preset radio station ..................... 22
RDS ....................................................................... 22Scrolling through RDS information .............. 22Setting the RDS clock ..................................... 22
NEWS ................................................................... 23Switching on NEWS function ....................... 23
Timer OperationsTimer setting ....................................................... 24Activating/Deactivating the timer ................ 24
Sleep timer setting ............................................. 25
Other ConnectionListening to an external source ...................... 25
Specifications ........................................... 26
Troubleshooting .................................... 27
7
En
glis
h
General Information
This product complies with the radiointerference requirements of theEuropean Community.
Refer to the type plate on the rear orbottom of the system for identificationand supply ratings.For users in the U.K.: please follow theinstructions on page 2.
Supplied accessories (page 3 - P1)
– USB PC LINK software installer CD-ROM– USB cable– Remote control and two AA batteries.– AM loop antenna– FM wire antenna– Video cinch cable (yellow)– AC power cord
Environmental informationAll unnecessary packaging has been omitted. Wehave tried to make the packaging easy toseparate into three materials: cardboard (box),polystyrene foam (buffer) and polyethylene (bags,protective foam sheet).
Your system consists of materials which can berecycled and reused if disassembled by aspecialised company. Please observe the localregulations regarding the disposal of packagingmaterials, exhausted batteries and oldequipment.
Care and safety information(page 3 - P2)
Avoid high temperatures, moisture,water and dust– Do not expose the system, batteries or discsto humidity, rain, sand or excessive heat (causedby heating equipment or direct sunlight). Alwayskeep the disc tray closed to avoid dust on thelens.
Avoid condensation problem– The lens may cloud over when the system issuddenly moved from cold to warmsurroundings, making it impossible to play a disc.Leave the system in the warm environment untilthe moisture evaporates.
Do not block the vents– In a cabinet, allows about 10cm (4 inches) offree space all around the system for adequateventilation.
Care of disc– To clean a CD, wipe it in a straight line fromthe centre towards the edge using a soft, lint-freecloth. A cleaning agent may damage the disc!– Write only on the printed side of a CDR(W)and only with a soft felt-tipped pen.– Handle the disc by its edge, do not touch thesurface.
Care of the cabinet– Use a soft cloth slightly moistened with a milddetergent solution. Do not use a solutioncontaining alcohol, spirits, ammonia or abrasives.
Finding a suitable location– Place the system on a flat, hard, and stablesurface.
Built-in safety circuit– Under extreme conditions, this system mayswitch to standby mode automatically. If thishappens, let the system cool down beforereusing it.
Power saving– This system is designed to use less than 1Wof electricity when switches to Eco Powerstandby. Disconnect the AC power cord fromthe power outlet when not in use.
8
En
glish
Main unit and remote control
1 ECO POWER indicator– Lights up when the system is in Eco Power
standby mode.
2 STANDBY ON B– Switches to Eco Power standby mode or turns
on the system.– *Switches to standby mode.
3 Display screen
4 CLOCK•TIMER (CLK/TIMER)– *Enters clock or timer setting mode.
5 RDS•NEWS– In tuner mode, selects RDS information.– In other modes, turns on/off news.
DISC 5
DISC 1
DISC 2
DISC 3
DISC 4
DISC 3 DISC 4 DISC 5DISC 2DISC 1
CDCD /CD-RCD-R/CD-RW CD-RW COMPCOM PATIBLETIBLE
STANDBYON
ECOPOWER
RDS•NEWS
C D
PROG
IRIR SENSOR
DSCDBB VAC
CLOCK •TIMER
TUNER AUX•GAMEUSB
PC LINK
SPEED PUNCH BLASTMODEMODE
MIX-IT
GAM E SOUNDGAM E SOUND
MAX MAX SOUNDSOUND
M AX SOUND • DIGITAL SOUND CONTROL VIRTUAL AM BIENCE CONTROL• DYNAM IC BASS BOO ST
AUDIO L.
VIDEO
AUDIO R.
GAM
EVOLUM E
SEARCH• TUNING
PREV•PRESET
STO
P•
DEM
OST
OP
NEXT•PRESET
PLA
Y•
PAU
SE
GAMEPORT MINI SYSTEM
MASTER VOLUME
OVERDRIVE
TURBOTURBOCRUISE
LEFTCHA
NNEL
CD3
CD2
CD1
CD4
CD5ARCADE CINEM ACONCERT
ALB M IX TITLEAM PMFM M WDIM SLEEPNEW SOPTIM AL JAZZ ROCK POP
TRKPROGSHUF REP DISC ALLCYBER HALLI.S.
DSCDSC
VACAC
OVERDRIVE
TURBOTURBOCRUISE
RIGHT
CHANNEL
1
2
3
4
5
6
!@#$
≤
£
™
¡
)
(
*
&
^
%
7
0
9
8
REPEAT PROGRAM SHUFFLE DISPLAY
DSC MUTEVAC
GAME
DIM SLEEP CLK/TIMER TIMER
VOL
MAX ON/OFF
GAME
MIX-ITSOUND
ALBUM
TITLE
USB PC LINKCD TUNER AUX/GAME
ON/OFF
§(≥•&
#
¤⁄º4!ª@
7
‹6
∞
*
8
09
CD1 CD2 CD3
CD4 CD5
Functional Overview
6 CD / TUNER / USB PC LINK /AUX•GAME
– Selects the relevant active mode.– CD: toggles between DISC 1~5.– TUNER: toggles between FM and MW band.– AUX•GAME: toggles between AUX and
GAMEPORT mode.
7 PREV•PRESET 4 (TITLE -) (í)NEXT•PRESET3 (TITLE +) (ë)
– CD: selects a track or selects a title from MP3disc.
– TUNER: selects a preset radio station.– CLOCK: sets the minutes.– USB PC LINK: selects a track from the playlist.
8 STOP•DEMO STOP Ç– Exits an operation.– CD: stops playback or clears a programme.– TUNER: *erases a preset radio station.– USB PC LINK: stops playback.
(only on the main unit)– *Turns on/off the demonstration mode.
* = Press and hold the button for more than two seconds.
9
En
glis
h
Functional Overview
9 SEARCH•TUNING (ALBUM 34)(à á)– CD: *searches backward/forward or selects an
album from MP3 disc.– TUNER: tunes the radio frequency up/down.– CLOCK: sets the hours.– USB PC LINK: *searches backward/forward.
0 PLAY•PAUSE ÉÅ– CD: starts/pauses playback.– USB PC LINK: starts/pauses playback.
(only on the main unit)TUNER: *enters Plug & Play mode and/or startspreset radio station installation.
! MAX SOUND (MAX ON/OFF)– Turns on/off the optimal mix of various sound
features.
@ MIX IT (GAME MIX IT)– Mixes the game sound with your favourite music
from one of these music source (CD, TUNER,USB PC LINK or AUX).
# MODE (GAME SOUND)– Selects different type of equaliser setting for
Gameport (SPEED, PUNCH or BLAST).
$ Connect the USB cable between the system andPC’s USB port.
% GAME VOLUME– Adjusts the game’s output volume level.
^ VIDEO– Use a video cable to connect to your game
console’s video output.
AUDIO L. / AUDIO R.– Use a audio cable to connect to your game
console’s left/right audio output.
& DBB– Selects different type of bass boost level settings
(DBB 1, DBB 2, DBB 3 or DBB OFF).
DSC– Selects different type of preset sound equaliser
settings (OPTIMAL, JAZZ, ROCK or POP).
VAC– Selects different type of environment ambience-
based equaliser settings (HALL, CINEMA,CONCERT, CYBER or ARCADE).
* MASTER VOLUME (VOL +-)– Adjusts the volume level.
( PROG (PROGRAM)– CD: starts or confirms tracks programming.– TUNER: starts *automatic/manual preset
programming.– CLOCK: selects 12- or 24-hour clock display.
)n
– Plug in the headphones jack. The speakersoutput will be cancelled.
¡ VU meters– Indicates signal strength of left/right channel.
™ iR SENSOR– Point the remote control towards this sensor.
£ Disc trays (1~5)
≤ OPEN•CLOSE 0 (DISC 1~5)– Opens/closes the individual disc tray.
Control buttons available on theremote only
∞ CD 1~5– Selects a disc tray to playback.
§ REPEAT– Repeats a track/disc/all programmed tracks.
≥ DIM– Turns on/off the dim mode.
• SLEEP– Sets the sleep timer function.
ª MUTE– Mutes or restores the volume.
º TIMER ON/OFF– Turns on/off the timer function.
⁄ SHUFFLE– Turns on/off the random play mode.
¤ DISPLAY– Displays the album and title name for MP3 disc.
‹ B
– Switches to Eco Power standby mode.– *Switches to standby mode.
* = Press and hold the button for more than two seconds.
10
En
glish
Connections
Game console
11
En
glis
h
Connections
WARNING!– Use only the supplied speakers. Thecombination of the main unit andspeakers provide the best sound. Usingother speakers can damage the unit andsound quality will be negatively affected.– Never make or change connectionswith the power switched on.– Connect the AC power cord to thepower outlet only after you have finishedhooking up everything.
Step 1: Connecting FM/AMantennas
– Place the AM loop antenna on a shelf orattach it to a stand or wall.– Extend the FM antenna and fix its ends to thewall.– Adjust the position of the antennas foroptimal reception.– Position the antennas as far as possible from aTV, VCR or other radiation source to preventunwanted noise.– For better FM stereo reception, connectexternal FM antenna.
Step 2: Connecting thespeakers
Connect the speaker wires to the SPEAKERSterminals, right speaker to "R" and left speaker to"L", coloured (marked) wire to "+" and black(unmarked) wire to "-". Fully insert thestripped portion of the speaker wire into theterminal as shown.
Notes:– Ensure that the speaker cables are correctlyconnected. Improper connections may damage thesystem due to short-circuit.– Do not connect more than one speaker to anyone pair of +/- speaker terminals.
Step 3: Connecting to PCUse the supplied USB cable to connect thesystem to your personal computer’s USB port.After installed the USB PC LINK applicationsoftware onto your PC, you are able to playbackyour music collection via the system (refer to“USB PC Link”).
Step 4: Connecting to gameconsole
IMPORTANT!Gameport inputs are solely for gameconsole only.
a. Use the game console’s video cable (notsupplied) to connect its video output to theGAMEPORT-VIDEO terminal.
b. Use the game console’s audio cables (notsupplied) to connect its audio outputs to theGAMEPORT-AUDIO L. / AUDIO R.terminals.
c. Use the video cable (yellow) to connect theVIDEO OUT terminal to the video input onthe TV for viewing.
Notes:– On the TV, the Video Input jack is usually yellowand might be labeled A/V In, CVBS, Composite orBaseband.– To avoid magnetic interference, do not positionthe front speakers too close to your TV.
Step 5: Connecting the ACpower cord
"AUTO INSTALL - PRESS PLAY" may appearon the display panel when the AC power cord isplugged into the power outlet for the first time.Press ÉÅ on the main unit to store all availableradio stations (page 3 - P3) or press Ç to exit(refer to “Tuner Operations”).
12
En
glish
Step 6: Inserting batteries intothe remote control
1
3
2
1 Open the battery compartment cover.
2 Insert two batteries type R06 or AA, followingthe indications (+-) inside thecompartment.
3 Close the cover.
Using the remote control to operatethe system
1 Aim the remote control directly at theremote sensor (iR) on the main unit.
2 Select the source you wish to control bypressing one of the source select keys on theremote control (for example CD, TUNER).
3 Then select the desired function (for exampleÉÅ, í, ë).
CAUTION!– Remove batteries if they are exhaustedor will not be used for a long time.– Do not use old and new or differenttypes of batteries in combination.– Batteries contain chemical substances,so they should be disposed of properly.
Connections
13
En
glis
h
Gameport Operations
About GameportGameport allows you to connect your gameconsole to this mini system which enables you toenjoy a total game immersion experience byhaving powerful sound output.
Preparation before use
Game consolefront panel
rear panel
SPEED PUNCH BLAST
MODEMODE
MIX-IT
GAME SOUND GAM E SOUND
GAME
VOLUM E
GAME GAME•AUXAUX
2
5
67
3
AUDIO L.
VIDEO
AUDIO R.
1
1 Connect your game console’s video and audiooutput to the GAMEPORT video and audioinputs respectively (refer to “Connections -Connecting to game console).
2 Connect your TV’s video input to the VIDEOOUT (CVBS) on the rear panel.
3 Connect all the AC power cord to the poweroutlet.
Start operating
4 Turn on the TV and set to the correctvideo-in channel.The TV’s video input channel may be calledAUX(iliary) IN, AUDIO/VIDEO (A/V) IN, EXT 1,etc. These channels are often near channel 00on your TV. Or, your TV remote control mayhave a button or switch that chooses differentvideo modes. See your TV manual for details.
5 Press AUX•GAME until “GAMEPORT” isdisplayed.
6 Press MODE (or GAME SOUND onremote) to select the type of sound settingthat best suit the game : SPEED, PUNCH,BLAST or OFF.
7 If you like to mix your game sound to yourfavourite music, press MIX-IT to select thedesired music source : CD, TUNER,USB PC LINK, AUX or OFF.
CD ™ “MIX-CD"TUNER ™ “MIX-TU"USB PC LINK ™ “MIX-USB"AUX ™ “MIX-AUX"OFF ™ “MIX-OFF"
8 If necessary, start playback your chosen mixersource.
9 Start playing your favourite game.
To adjust the game console’s volumelevel
Adjust GAME VOLUME.
To change the mixer source Press MIX-IT.
To control the current active mixersource
Press the respective source button (forexample, CD, TUNER) on the remote control,then select the desired function (for exampleÉ, í, ë).For example, if CD is the mixer source and tochange the disc tray, you have to press CD, thenpress CD 1~5 to select the desired disc tray.
Notes:– You can only activate GAME VOLUME andMIX-IT while in game source mode.– If your game console is switched on, the videoimage will always appear on the TV even thoughyou are not in the gameport mode.
14
En
glish
USB PC Link
Quick Setup Guide
PC system requirement
– Windows 98/ ME/ 2000/ XP– Intel Pentium MMXX200 or higher– CD-ROM drive– USB port– Free hard disk space : 15 MB for the
software
Install MusicMatch software
POWER ON/OFF
12
3
5
4
1 Use the supplied USB cable to connect theaudio system to your personal computer’sUSB port.
2 Press USB PC LINK.
3 Turn on the PC and insert the USB PC LINKinstaller disc (which comes with this product)onto the PC’s CD-ROM drive.This application software can also be downloadedfrom “http://www.audio.philips.com”.
IMPORTANT!Please use this customised MusicMatchsoftware for your USB PC Linkapplication. Remember to un-install allother MusicMatch jukebox software firstfrom your PC system (if available).
4 The installation guide will appear automatically. Ifit does not, go to the CD-ROM drive inWindows Explorer and double click on the“USBPCLINK.exe”. Then perform the followingsteps:– First, select your desired language from the
list.– Then, select “installer driver” and follow by
“installer MusicMatch jukebox”.– Select other options (Tutorial, Free goodies,
FAQ).
Note:– You are advised to read the MusicMatch tutorialbefore using it for the first time. Make sure themute function on the PC is deactivated in order toensure sound output from the Audio System. Foroptimum performance, the equaliser function inMusicMatch should be set to a low level.
5 Launch the “MUSICMATCH JUKEBOX” andchoose to do one of the followings :
To create a “Playlist”Select “Open” button on the MusicMatchJukebox and simply drag/drop the music tracksfrom anywhere on your PC into the “Playlist”window. Remember to save this “Playlist” forfuture use.
To create a music libraryA music library of all stored music files availableon your PC can be setup by simply select “add”function on the MusicMatch Jukebox. Oncecreated, you may then choose to drag/drop anymusic tracks from this library to a “Playlist” formusic playback.
Note:– It is not possible to create a playlist from thesystem’s 5 CD changer. If you encounter problemusing USB PC LINK, please refer to the FAQ(Frequently Asked Questions) stored in your USB PCLINK installer disc or visit “www.audio.philips.com”for latest update on FAQ.
15
En
glis
h
USB PC Link
Enable digital CD audio output
Before playing the CD through your PC’sCD-ROM drive, it is necessary to configure yourPC’s hardware as follows:
For Windows ME/ 2000/ XP1 Enter the system control panel menu and
select :“SYSTEM ™ HARDWARE ™DEVICE MANAGER ™ CD-ROM DRIVES ™ACTION–PROPERTIES ™ PROPERTIES”.
OR
For Windows 98Enter the system control panel menu andselect “MULTIMEDIA” and “CD MUSIC”.
2 Check the ‘Enable digital CD audio for thisCD-ROM device’ setting option is selected(enabled).
Note:– You may need to refer to your PC’s manual forcorrect configuration.
Connecting to USB PC LINKUSB PC LINK allows you to playback your musiccollection from the PC via the powerful amplifierand speakers of this system.
IMPORTANT!Make sure the MusicMatch software hasbeen installed. Refer to “Quick SetupGuide” for USB PC Link.
REPEAT SHUFFLE
DIM SLEEP CLK/TIMER TIMER
VOL
ALBUM
TITLE
USB PC LINK
ON/OFF
2
3
4
51
1 Turn on your computer and launch the“MUSICMATCH JUKEBOX”. The volume level of PC should not be putinto mute.
2 Press USB PC LINK. If the audio streaming is detected,“CONNECTING” is displayed and the USBindicator will be flashing. If “NO CONNECTION” is displayed, check theconnection between your PC and mini system.
3 Press í or ë until the desired track in theplaylist is highlighted.
4 Press ÉÅ to start playback. The track information will appear on thedisplay. The display only supports Englishcharacters.
During playback,– Press SHUFFLE to play all available tracks inthe playlist in random order.– Press REPEAT to repeat playback of all thetracks in the playlist.
5 To exit, select another active mode orpress Ç.
16
En
glish
Switching on/off
Switching to active mode
Press CD, TUNER, USB PC LINK orAUX•GAME.
Switching to Eco Power standby mode
Press B. ECO POWER button lights up. The display screen will go blank.
Switching to standby mode (viewclock)
Press and hold B. The clock is displayed. While in standby mode, pressingCLOCK•TIMER button will switch the system toEco Power standby mode.
Note:– Before switching the system to Eco Powerstandby or standby mode, make sure thedemonstration mode has been deactivated.
Demonstration modeIf the demonstration mode is active, wheneveryou switch the system to Eco Power standby orstandby mode, it will begin showing the variousfeatures offered by the system.
To activate the demonstration In Eco Power standby/standby mode,
press and hold Ç on the main unit until"DEMO ON" is displayed.
To deactivate the demonstration Press and hold Ç on the main unit until
"DEMO OFF" is displayed.
Basic Operations
Setting the clockThe clock can be set in either 12-hour or24-hour mode ("11:59 PM" or "23:59" forexample).
CLK/TIMER
(00:00 î 12:00AM)
(00:00 / 12:00AM)
(00:00 / 12:00AM)5
4
3
1 2, 6,
2
1 Press and hold CLK/TIMER (orCLOCK•TIMER on main unit) until"SELECT CLOCK OR TIMER" is displayed.
2 Press ë to change the display to "CLOCK"and press CLK/TIMER (CLOCK•TIMER)again to confirm.
3 Press PROGRAM (PROG) repeatedly tochange between 12-hour and 24-hour clockmode.
4 Press à or á repeatedly to set the hour.
5 Press í or ë repeatedly to set the minute.
6 Press CLK/TIMER (CLOCK•TIMER) tostore the setting. The clock will start working.
To view the clock time in any activemode
Press CLK/TIMER (CLOCK•TIMER)once. The clock is displayed for a few seconds.
Notes:– The clock setting will be erased when the systemis disconnected from the power supply.– The system will exit clock setting mode if nobutton is pressed within 90 seconds.– To set the clock automatically through the timeinformation in the RDS signal, refer to "TunerOperations - Setting the RDS clock".
17
En
glis
h
Basic Operations
Dimming system’s display screenYou can select the desired brightness for thedisplay panel.
In any active mode, press DIM on remoterepeatedly to turn on/off dim mode. DIM is shown, except for DIM OFF mode.
Volume control
Adjust MASTER VOLUME (or pressVOL +/- on remote) to increase ordecrease the sound level. "VOL MIN" is the minimum volume level and"VOL MAX" is the maximum volume level.
To switch off the volume temporarily Press MUTE on the remote.
Playback will continue without sound and"MUTE" is displayed. To restore the volume, press MUTE again orincrease the volume level.
Sound controlMAX sound, DSC and VAC sound featurescannot be activated on the same time.While in game mode, all the sound controlfeatures are not available for selection, exceptDBB and Game Sound control.
MAX sound
MAX sound provides the best mixture ofvarious sound features (DSC, VAC for example).
Press MAX SOUND (or MAX ON/OFFon remote). If activated, the MAX SOUND button lightsup. All other sound effects (DSC, VAC or DBB)will be switched off automatically
Digital Sound Control
DSC provides a different type of preset soundequaliser setting.
Press DSC repeatedly to select : OPTIMAL,JAZZ, ROCK or POP.
Virtual Ambience Control
VAC provides a different type of environment-based equaliser setting.
Press VAC repeatedly to select : HALL,CINEMA, CONCERT, CYBER or ARCADE.
Dynamic Bass Boost
DBB enhances the bass response.
Press DBB repeatedly to select : DBB 1,DBB 2, DBB 3 or DBB OFF. Some discs might be recorded in highmodulation, which causes a distortion at highvolume. If this occurs, switch off DBB or reducethe volume.
Automatic DSC-DBB and VAC-DBBselectionThe best DBB setting is generated automaticallyfor each DSC, VAC or Game Sound selection.You can manually select the DBB setting thatbest suits your listening environment.
18
En
glish
IMPORTANT!– This system is designed for regulardiscs. Therefore, do not use anyaccessories such as disc stabiliser rings ordisc treatment sheets, etc., as offered onthe market, because they may jam thechanger mechanism.– Do not load more than one disc ontoeach tray.
Playable discsThis system is able to play :– All pre-recorded audio CDs– All finalised audio CDR and audio CDRW
discs– MP3-CDs (CD-ROMs with MP3 tracks)
Loading discs (page 3 - P4)
1 Press OPEN•CLOSE 0 DISC 1 button ontop of the main unit to open disc tray 1.
2 Load a disc with the label side facing up. Fordouble-sided discs, load the side you want toplay facing up.
3 Press OPEN•CLOSE 0 DISC 1 buttonagain to close the disc tray. “READING“ is displayed. The selected disctray, total number of tracks and the playing timewill appear on the display.
4 Repeat steps 1~3 for loading discs onto thedisc trays 2~5.
Notes:– To ensure good system performance, wait untilthe disc trays completely read the disc(s) beforeproceeding.– Only one tray can be opened at each time. Ifyou open the second tray before closing the firsttray, the first tray will automatically close before thesecond tray opens.
Basic playback controls
Load discs (page 3 - P4).
To play all discs on the disc trays
Press ÉÅ.OR
In stop mode, press CD to select a disc trayto begin, then press ÉÅ. All the available discs will play once, then stop.
To play the selected disc only Press one of the CD 1~5 buttons on
remote. The selected disc will play once, then stop.
To select a desired track Press í or ë repeatedly until the desired
track is displayed. During random play (shuffle mode), pressingí will not affect the current playback.
To search for a particular passageduring playback
Press and hold à or á and release it whenthe desired passage is located. During searching, the volume will be reduced.For MP3 disc, the volume will be muted.
To replace discs without interruptingplayback
Press OPEN•CLOSE 0 buttons of theinactive disc trays (refer to “Loading discs”).For example, if currently disc tray 1 is playing,you can replace the discs on disc tray 2~5.
To interrupt playback Press ÉÅ.
To resume normal playback, repeat theabove.
To stop playback Press Ç.
If the system remains in stop mode for 30minutes, it will switch to Eco Power standbymode.
Disc Operations
19
En
glis
h
Playing an MP3 disc
3
4
2DISC 1DISC 1
DISC 2DISC 2
DISC 3DISC 3
DISC 4DISC 4
DISC DISC 3 DISC DISC 4 DISC DISC 5DISC DISC 2DISC DISC 1
CDCD /CD-RCD-R/CD-RW CD-RW COMPCOM PATIBLETIBLE
DISC 1DISC 1
1
A02 T001
ALB
TITLE
A02 T008
1 Load an MP3 disc. The disc reading time may exceed 10seconds due to the large number of songscompiled into one disc. "AXX TYYY" is displayed. XX is the currentalbum number and YYY is the current titlenumber.
2 Press à / á (ALBUM 43) to select adesired album.
3 Press í / ë (TITLE -+) to select adesired title.
4 Press ÉÅ to start playback.
During playback, press DISPLAY to showthe album and title name.
Supported MP3 disc formats:– ISO9660, Joliet, UDF 1.5– Maximum title number : 999 (depending on
filename length)– Maximum album number : 99– Supported sampling frequencies : 32 kHz,
44.1 kHz, 48 kHz– Supported Bit-rates : 32~256 (kbps), variable
bitrates– ID3 tags : V1.1, V2.2, V2.3, V2.4
Repeat and ShuffleYou can select and change the various playmodes before or during playback.
Repeat play
1 Press REPEAT on the remote repeatedly toselect :
A
B
C
D
E
A – to repeat playback of the current track.B – to repeat playback of the current disc.C – to repeat playback of all available discs
(not available for this model).D – to repeat playback of the current
programmed track (only if the programmemode is active)
E – to repeat playback of all the programmedtracks (only if the programme mode isactive)
2 To resume normal playback, press REPEATuntil "OFF" is displayed.
Random play
Press SHUFFLE on the remote to turnon/off the shuffling mode. If activated, SHUF is shown and the repeatmode (if any) will be cancelled. The random play will start from the currentdisc tray. Only after all the tracks in the activedisc tray has been shuffled, then it will change tothe next available disc tray. If programme mode is active, only theprogrammed tracks will be played in randomorder.
Note:– Pressing the OPEN•CLOSE button will cancel allrepeat and shuffling modes.
Disc Operations
20
En
glish
Programming the disc tracksProgramming tracks is possible when playback isstopped. Up to 99 tracks can be stored in thememory in any order.
IMPORTANT!It is only possible to programme fromthe current selected disc tray.
DISC 1DISC 1
DISC 2DISC 2
DISC 3DISC 3
DISC 4DISC 4
DISC DISC 3 DISC DISC 4 DISC DISC 5DISC DISC 2DISC DISC 1
CDCD /CD-RCD-R/CD-RW CD-RW COMPCOM PATIBLETIBLE
DISC 1DISC 1
2
4
6
7
3 5,
1
1 Load the desired discs on the disc trays (referto “Loading discs”).
2 Press CD or one of the CD 1~5 buttons toselect a disc.
3 Press PROGRAM (PROG) to startprogramming. PROG starts flashing.
4 Press í or ë repeatedly to select thedesired track.
For MP3 disc, press à / á (ALBUM 43) andí / ë (TITLE -+) to select the desiredalbum and title for programming.
5 Press PROGRAM (PROG) to store.
Repeat steps 4–5 to select other tracks. If you attempt to programme more than 99tracks, "PROGRAM FULL" is displayed.
6 To start programme play, press ÉÅ.
7 To stop playback or to end the programming,press Ç once. PROG stays and the programme moderemains active.
Disc Operations
Notes:– If the total playing time reached 100 minutes orif one of the programmed tracks has a numbergreater than 30, then "--:--" is displayed insteadof the total playing time.– The system will exit programming mode if nobutton is pressed within 20 seconds.
Checking the programme
1 Stop playback and press í or ë repeatedly.
2 Press Ç to exit.OR
Press ÉÅ to start playback from the currentprogrammed track
Clearing the programme
Stop playback, then press Ç to clear theprogram.OR
Press the OPEN•CLOSE 0 button of thedisc tray. PROG disappears and "PROGRAM CLEARED"is displayed.
Note:– The programme will be erased if the system isdisconnected from the power supply or you switchto other source mode.
21
En
glis
h
Tuner Operations
IMPORTANT!Make sure the FM and MW antennas areconnected.
Tuning to radio stations
1 Press TUNER to enter tuner mode. Toselect another waveband (FM or MW), pressTUNER again.
2 Press and hold à or á until the frequencyindication starts to change, then release. The system automatically tunes to the nextstrong signal radio reception. lights up for FM stereo reception. RDS lights up for RDS station (in FM bandonly).
For tuning to a weak signal station, Press à or á briefly and repeatedly until an
optimal reception is found.
Presetting radio stationsYou can store up to 40 preset radio stations inthe memory, starting from FM and followed byMW bands.
Notes:– The system will exit presetting mode if no buttonis pressed within 20 seconds.– If no stereo frequency is detected during Plugand Play, "CHECK ANTENNA" is displayed.
Using the Plug and Play (page 3 - P3)
Plug and Play allows you to store all availableradio stations automatically.
1 Connect the system to the power supply,"AUTO INSTALL - PRESS PLAY" isdisplayed.OR
In Eco Power standby/standby mode,press and hold ÉÅ on the main unit until"AUTO INSTALL - PRESS PLAY" isdisplayed.
2 Press ÉÅ on the main unit to startinstallation. "INSTALL TUNER" is displayed. All previously stored radio stations will bereplaced. Once completed, the last tuned radio stationwill be played. Once completed, the last tuned radio station(or the first available RDS station) will be played.
3 If the first preset is a RDS station, it willproceed to set the RDS clock. "INSTALL" is displayed, followed by "TIME"and "SEARCH RDS TIME". When RDS time is read, "RDS TIME" isdisplayed and the current time will be stored. If RDS station does not transmit RDS timewithin 90 seconds, “NO RDS TIME” is displayedand the programme will exit automatically.
Automatic presetting
You can start the automatic presetting from aselected preset number.
1 In tuner mode, press í or ë to select apreset number.
2 Press and hold PROGRAM (PROG) until"AUTO" is displayed. If a radio station has been stored in one ofthe presets, it will not be stored again underanother preset number. If no preset number is selected, automaticpreset will begin from preset (1) and all yourformer presets will be overridden.
Manual presetting
You can choose to store only the favourite radiostations.
1 Tune to your desired radio station (refer to“Tuning to radio stations”).
2 Press PROGRAM (PROG). The preset number starts flashing. If you wantto store the radio station in another presetnumber, press í or ë.
3 Press PROGRAM (PROG) again to store.
Repeat steps 1–3 to store other radiostations.
22
En
glish
Selecting a preset radio station
In tuner mode, press í or ë. The preset number, radio frequency, andwaveband are displayed.
Deleting a preset radio station
Press and hold Ç until “PRESETDELETED” is displayed. The current preset radio station will bedeleted. All other preset radio stations with highernumbers are decreased by one.
RDSRDS (Radio Data System) is a service thatallows FM stations to show additionalinformation. If you are receiving a RDS station,RDS and the station name are displayed.
Scrolling through RDS information
Tuned to a RDS radio station from FM band,then press RDS•NEWS repeatedly to selectthe following information (if available):– Station name– Programme type (for example: News, Affairs,
Sport, etc.)– Radio text messages– Frequency
Setting the RDS clock
Some RDS radio station may be transmitting areal clock time at an interval of every minute. Itis possible to set the clock by using a time signalwhich is broadcast together with the RDS signal.
1 Tuned to a RDS station from FM band (referto “Tuning to radio stations”).
2 Press and hold CLK/TIMER (orCLOCK•TIMER on main unit) until"SELECT CLOCK OR TIMER" is displayed.
3 Press ë to change the display to "CLOCK"and press CLK/TIMER (CLOCK•TIMER)again to confirm.
4 Press RDS•NEWS. "SEARCH RDS TIME" is displayed. When RDS time is read, the current time willbe stored. If the RDS station does not transmit RDStime within 90 seconds, "NO RDS TIME" isdisplayed.
Note:– Some RDS radio station may be transmitting areal time clock at a minute interval. The accuracyof the transmitted time depends on the transmittingRDS radio station.
Tuner Operations
23
En
glis
h
Tuner Operations
NEWSYou may set up the tuner in such a way thatlistening to CD or external source is interruptedby the NEWS of a RDS station. This only worksif the RDS station broadcasts a NEWS signalwhile sending the news.
IMPORTANT!You can activate NEWS function fromany source mode except TUNER.
Switching on NEWS function
1 In any active mode, press RDS•NEWS until"NEWS" is displayed. NEWS is shown. The system will scan the radio stations storedin the first five (5) preset and wait for the NewsProgramme Type data to be available in any ofthese RDS stations. While searching NEWS in progress, thecurrent active mode remains uninterrupted.
2 When NEWS transmission is detected, thesystem will switch to Tuner mode. NEWS starts flashing.
If no RDS station is detected in the first fivepresets, the system will exit NEWS function. "NO RDS NEWS" is displayed.
Notes:– You have to exit Tuner mode before selectingNEWS function.– Before you activate the NEWS feature, ensurethat the first five presets have RDS stations.– The NEWS works only once for each activation.
To cancel NEWS function Press RDS•NEWS again or switch the
system to tuner mode.OR
During news bulletin, press any other availablesource keys to execute the relevant sourcemode.
24
En
glish
Timer settingThe system can switch on to CD, TUNER orUSB PC LINK mode automatically at a presettime, serving as an alarm to wake you up.
IMPORTANT!– Before setting the timer, ensure thatthe clock is set correctly.– The volume of the timer will increasegradually to the last tuned volume level.If the last tuned volume level is too low,the set will then increase to apredetermined minimum audible level.
CLK/TIMER TIMER ON/OFF
(00:00 / 12:00AM)
(00:00 / 12:00AM)
3
4
4
1 2,
(CD / TUNER / USB PC LINK)
5,
2
1 Press and hold CLK/TIMER (orCLOCK•TIMER on main unit) until"SELECT CLOCK OR TIMER" is displayed.
2 Press ë to change the display to "TIMER"and press CLK/TIMER again to confirm.
3 Press CD or TUNER or USB PC LINK toselect the wake-up source.
CD ™ “CD XX:XX"TUNER ™ “TU XX:XX”USB PC LINK ™ “USB XX:XX”
4 Press à or á (for hours) and í or ë(for minutes) repeatedly to set the wake uptime.
5 Press CLK/TIMER to store the setting. The timer will always be switched on after ithas been set. icon remains on the display. It indicates thetimer is activated.
At the preset time, the selected soundsource will be played for 30 minutesbefore it switches to Eco Power standbymode (if no button is being pressed within thetime frame). CD – playing the first track of the lastselected disc. If the last selected disc tray isempty, it will switch to the next available disc. Ifall the disc trays are not available, it will switch toTuner mode. TUNER – playing the last tuned radio station. USB PC LINK – playing the last selectedplaylist. If the connection fails, it will switch toTuner mode. Refer to “USB PC Link” for properconnection and setup before use.
Activating/Deactivating the timer
Press TIMER ON/OFF on the remote toturn off the timer or turn on to the lastsetting again. If activated, the timer information will displayfor a few seconds, then the system resumes tothe last active source or stays in standby mode. If deactivated, “OFF” is displayed.
Note:– The system will exit timer setting mode if nobutton is pressed within 90 seconds.
Timer Operations
25
En
glis
h
Timer Operations Other Connection
Listening to an external sourceYou can listen to the sound of the connectedexternal device through your system’s speakers.
L
R
AUDIO OUT
LRAUXIN
PLAYVOL
ALBUM
TITLE
USB PC LINKCD TUNER AUX/GAME
CD1 CD2 CD3
CD4 CD5
AUX/GAME
AUX
1
32
1 Use the red/white audio cables to connectthe system’s AUX IN (R/L) terminals to theAUDIO OUT terminals on the otheraudio/visual device (such as a TV, VCR, LaserDisc player, DVD player or CD recorder) If the connecting device has only a a singleaudio out terminal, connect it to the AUX IN leftterminal. Alternatively, you can use a “single todouble” cinch cable, but the output sounds stillremain mono.
2 Press AUX/GAME until “AUX” is displayed.
3 Press PLAY on the connected device to startplayback.
Notes:– All the sound control features (DSC, VAC forexample) are available for selection.– Always refer to the owner’s manual of the otherequipment for complete connection and use details.
Sleep timer settingThe sleep timer enables the system to switch toEco Power standby mode automatically at apreset time.
1 Press SLEEP repeatedly until it reaches thedesired preset turn-off time. The selections are as follows (time inminutes):
15 ™ 30 ™ 45 ™ 60 ™ 90 ™ 120 ™OFF ™ 15 …
SLEEP is shown, except for "OFF" mode. To view or change the setting, repeat theabove.
2 Before the system switches to Eco Powerstandby mode, a countdown of 10 seconds isdisplayed.
"SLEEP 10" ™ "SLEEP 9".... ™ "SLEEP 1"™ "SLEEP"
To cancel the sleep timer function Press SLEEP repeatedly until "OFF" is
displayed, or press the STANDBY ON Bbutton.
26
En
glish
AMPLIFIEROutput power 2 x 280 W MPO
2 x 140 W RMS(1)
Signal-to-noise ratio ≥ 75 dBA (IEC)Frequency response 50 – 18000 Hz, –3 dBInput sensitivityAUX In 640 m VGameport 310 mV
OutputSpeakers ≥ 6 ΩHeadphones 32 Ω – 1000 Ω
(1) (6 Ω, 1 kHz, 10% THD)
DISC PLAYERProgrammable tracks 99Frequency response 20 – 20000 Hz, –3 dBSignal-to-noise ratio ≥ 76 dBAChannel separation ≥ 60 dB (1 kHz)MPEG 1 Layer 3 (MP3-CD) MPEG AUDIOMP3-CD bit rate 32-256 kbps
(128 kbps advised)Sampling frequencies 32, 44.1, 48 kHz
USBFrequency response 20 – 20000 Hz, –3 dBSignal-to-noise ratio ≥ 75 dBAChannel separation ≥ 40 dB (1 kHz)Total harmonic distortion < 0.3% (1 kHz)
TUNERFM wave range 87.5 – 108 MHzMW wave range 531 – 1602 kHzNumber of presets 40AntennaFM 75 Ω wireAM Loop antenna
Specifications
SPEAKERSSystem 3 way, Bass reflexImpedance 6 ΩWoofer 1 x 6.5"Tweeter 1 x 2" Ferrofluid cooledDimensions (w x h x d) 348 x 322 x 245 (mm)Weight 8.7 kg each
GENERALMaterial/finish Polystyrene/MetalAC Power 220 – 230 V / 50 HzPower ConsumptionActive 175 WStandby < 25 WEco Power Standby < 1 W
Dimensions (w x h x d) 265 x 322 x 390 (mm)Weight (without speakers) 8.6 kg
Specifications and external appearance are subjectto change without notice.
27
En
glis
hWARNINGUnder no circumstances should you try to repair the system yourself, as this will invalidate thewarranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If youare unable to remedy a problem by following these hints, consult your dealer or Philips forhelp.
Troubleshooting
When in USB PC LINK mode, “NOCONNECTION” is displayed.
Radio reception is poor.
“NO DISC” is displayed or the disc cannotbe played.
The system does not react when buttons arepressed.
Sound cannot be heard or is of poor quality.
The remote control does not functionproperly.
The timer is not working.
The system displays features automatically andbuttons start flashing.
Check the connection between your PC and thesystem and the inital setup required, see “Connections”and “USB PC Link”.
Make sure the connected PC is turned on.
If the signal is too weak, adjust the antenna or connectan external antenna for better reception.
Increase the distance between the system and your TVor VCR.
Insert a disc. Load in the disc with label facing right. Replace or clean the disc, see “Care and safety
information”. Use a finalised CD-R(W) or a correct format disc.
Remove and reconnect the AC power cord and switchon the system again.
Adjust the volume. Disconnect the headphones. Check that the speakers are connected correctly. Check that the AC power cord is connected properly. When in USB PC LINK mode, check that the PC’s
volume is not put into mute. When playing CD from PC’s CD drive, refer to “USB
PC Link - Enable digital CD audio output“.
Select the source (CD or TUNER, for example) beforepressing the function button (ÉÅ, S , T).
Reduce the distance between the remote control andthe system.
Replace the battery. Point the remote control directly toward the IR sensor.
Set the clock correctly. Press TIMER ON/OFF to switch on the timer.
Press and hold DEMO STOP on the main unit to switchoff the demonstration mode.
Problem Solution
Refer to the FAQ (Frequently Asked Questions) on the supplied CD-ROM or visit our website“www.audio.philips.com” for latest update on FAQ.
Related Documents
