User Manual Microwave combi-oven LAM7001
User Manual
Microwave combi-ovenLAM7001
appliance condensates on cavity wallsand can cause corrosion.
Clean regularly the appliance to preventthe deterioration of the surface material.
Remaining fat or food in the appliancecan cause fire.
Clean the appliance with a moist softcloth. Only use neutral detergents. Donot use abrasive products, abrasivecleaning pads, solvents or metal objects.
If you use an oven spray, obey the safetyinstructions on the packaging.
Do not clean the catalytic enamel (ifapplicable) with any kind of detergent.
Internal lightThe type of light bulb or halogen lampused for this appliance is only forhousehold appliances. Do not use it forhouse lighting.
WARNING! Risk of electricalshock.
Before replacing the lamp, disconnectthe appliance from the power supply.
Only use lamps with the samespecifications.
Disposal
WARNING! Risk of injury orsuffocation.
Disconnect the appliance from the mainssupply.
Cut off the mains cable and discard it.Remove the door catch to preventchildren and pets to get closed in theappliance.
PRODUCT DESCRIPTION
General overview
1 2
8
4
3
1
2
3
6
4
5
7
1 Control panel2 Electronic programmer3 Heating element4 Microwave generator5 Lamp6 Fan7 Shelf support, removable8 Shelf positions
6
Accessories
Wire shelf
For cookware, cake tins, roasts.
Baking tray
For cakes and biscuits.
CONTROL PANEL
Electronic programmer
1110987654321
Use the sensor fields to operate the appliance.
Sensor Function Comment
1 - Display Shows the current settings of the appliance.
2ON / OFF To activate and deactivate the appliance.
3
Heating Func-tions or AssistedCooking
function or the menu: Assisted Cooking. Touch the
Heating Functions, Assisted Cooking. To activate or
4
Microwave func-tion
To activate the Microwave function. You can use itwhen the appliance is deactivated. When you use theMicrowave function with the function: Duration formore than 7 minutes and in Combi mode, the Micro-wave power cannot be more than 600 W.
7
First ConnectionWhen you connect the appliance to the mains or after a power cut, you will have toset the language, display contrast, display brightness and the time of the day.
1. Press or to set the value.2. Press
A
DE
B C
Symbol Function
Temperature The display shows the temperature.
Time Indication The display shows how long the heating
function operates. Press and atthe same time to reset the time.
Heat-up Indicator The display shows the temperature inthe appliance.
Fast Heat Up Indicator The function is active. It decreases theheat up time.
Weight Automatic The display shows that the automaticweight system is active or that weightcan be changed.
Heat + Hold The function is active.
BEFORE FIRST USE
WARNING! Refer to Safetychapters.
Initial CleaningRemove all accessories and removableshelf supports from the appliance.
Refer to "Care and cleaning"chapter.
Clean the appliance before first use.
Put the accessories and the removableshelf supports back to their initial position.
DAILY USE
WARNING! Refer to Safetychapters.
Navigating the menus1. Activate the appliance.2. Press or to select the menu
option.3. Press to move to the submenu or
accept the setting.
At each point you can go backto the main menu with .
9
23
1
*
44
Before installation
The product should only be installed by suitably persons.
The product must be installed in accordance with all local regulations.
Prior to installation, visually check the product for any damage/defects. Do not install if any issues are found.
Damaged products may cause risks to your own safety.
Installation
The appliance is intended for installation in Howdens kitchen cabinets.
Surfaces, synthetic laminates and adhesives used must be heat resistant.
Kitchen cabinets must be set level and
If there is a drawer beneath the oven, a shelf must be installed between oven and drawer.
The following installation drawings are representational and may not match exactly with your appliance.
560mm
560mm
460 mm(min)555mm
547mm
555mm
445mm
547mm
20 mm
20 mm
550 mmmin depth
550 mmmin depth
*
*
*
445mm
594mm
455mm
455mm
594mm
450 mm(min)
Note: Remove carcase rear panel to assist with ventilation.
A minimum of 150cm² ventilation gap is required as Illustrated(35mm x 500mm) cut out positioned centrally.
*
Tower Unit Installation
Built under installation
If supplied, please stick your self adhesive product rating plate here, or make a note of the product serial number below in the box below for future reference.
Serial Number : ...........................................................................................
867303247-A-142014 v1 29/01/2015