Different Methodologies for Repair of Cracks in PQC in Concrete Pavements Dr. Yash. P. Gupta, Technical Advisor, COWI - DIPL Consortium, Naini Bridge Project, Allahabad, India And (Ex) Material Consultant Allahabad By Pass Project, Allahabad Large scale construction of Bridges & Highways is going on in India and World over. They are mostly made as rigid pavements using Pavement Quality Concrete (PQC). On one hand, concrete is a very good and strong material, but it develops cracks due to temperature, shrinkage, creep etc. Until unless enough precautions are taken, some cracks do come up on concrete surface. Prominent cracks should be repaired for better performance and longer life of Highways/pavements. To repair these cracks, several materials and procedure have been developed. The efficiency of these materials and procedures depend on the type of crack, weather conditions and applicator efficiency. In this paper various procedures of crack repair are described.
19
Embed
Methodologies for Repair of Cracks in PQC in Concrete Pavements - NBM Media[1]
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Different Methodologies for Repair of Cracks in PQC in Concrete Pavements
Dr. Yash. P. Gupta, Technical Advisor, COWI - DIPL Consortium, Naini
Bridge Project, Allahabad, India And (Ex) Material Consultant Allahabad By
Pass Project, Allahabad
Large scale construction of Bridges & Highways is going on in India and
World over. They are mostly made as rigid pavements using Pavement
Quality Concrete (PQC). On one hand, concrete is a very good and strong
material, but it develops cracks due to temperature, shrinkage, creep etc.
Until unless enough precautions are taken, some cracks do come up on
concrete surface. Prominent cracks should be repaired for better
performance and longer life of Highways/pavements. To repair these cracks,
several materials and procedure have been developed. The efficiency of
these materials and procedures depend on the type of crack, weather
conditions and applicator efficiency.
In this paper various procedures of crack repair are described. However, any
procedure in general should be first tried on pilot basis and then depending
upon its success, repairing of cracks be done at site. A procedure of injecting
low viscosity Epoxy Material is an excellent material. It is discussed here and
can be used for the repair of cracks.
Why Concrete Cracks
First it is necessary to understand why the concrete cracks. There can be
many reasons why the concrete cracks. These need to be understood from
its reaction and setting pattern point of view. The main reason is improper
concrete mix design and laying / jointing practice related to the inherent
nature of concrete to change volumetrically due to moisture, reaction and
thermal effects etc. The incidence of cracks can be minimized by improving
concrete mix design, laying time weather condition and jointing practices
with timely saw cutting and properly managed curing.
Concrete roads, properly designed and constructed, should require little, if
any, maintenance over its design life. Still, proper and timed maintenance
may extend the life of the pavement even beyond designed service life.
Concrete pavements undergo stress and strain due to traffic and climatic
effects. However, as long as sub grade is properly compacted, any
variation/change in support (due to moisture-changes) has little effect on
performance. Proper weather during construction and laying / jointing
practice will eliminate most premature distresses. Otherwise, some
shrinkage cracking may appear before the road is opened to traffic.
Normally, there is no reason why a concrete road should not perform well
during the designed life span if properly laid and cared through
maintenance.
Identification and Location of Cracks on PQC Surface
A. Identification of Affected Area
The relevant pavement is surveyed and effected portion marked with a
marker. The area can be struck with a hand held hammer to further
qualify and quantify the crack. The dull and hollow sound is emitted
from the unsound concrete whereas metallic sound is emitted from
sound concrete. The boundary of area to be treated should be marked
and as far as possible rectangular and normally about 50 mm should
be taken into the sound concrete to make sure that all unsound
concrete is included. Cracks and its location can be identified from top
surface of PQC and some from sides. Then judge the extent of cracking
in concrete by any one of following methods.
1. Visual Survey of the effected PQC Surface. This should preferably
be done after rains or after washing the surface with water.
2. Measure the width of cracks at top of PQC surface by using
thickness gauges.
3. NDT: Non destructively estimate the extend of cracking by using
NDT technique. Commonly adopted NDT technique is Ultrasonic
Pulse Velocity Measurements using UPV meter.
4. Core Drilling: Take cores at the apparent location of cracks which
are seen from top, upto full depth of PQC. Generally cores can be
taken of 100 or 150 mm in diameter.
B. Classification of Cracks and Repair Methods
The cracks may be classified in following categories:
a. Small Hair Cracks (< 1mm) - seen mainly at top.
b. Medium / Partial or half depth cracks
c. Full depth cracks
d. Many checker cracks in any one panel of PQC.
e. Pot holes and Corner damages
f. Settlement of panel or Multiple cracks near expansion joints.
Such Surface Cracks develops in PQC due to temperature difference,
late joint cutting, and defective curing of PQC etc. The cracks will allow
water / mud /debris going into the cracks and widens them further.
Medium or Full depth cracks
Some typical Medium or Full depth cracks are shown in Figures 1.
Figure 1: Typical Cracks in PQC Pavement Surface
Settlement of panel or Multiple cracks near expansion joints:
Such cracks normally develop because of poor compaction or poor Concrete Mix Design.
Some typical cracks are shown in Figure 2.
Figure 2: Typical Panel Settlement or near panel Cracks
Visually examine all such cracks and decide which crack is to be
repaired on the basis of width, depth and its pattern. In general hair or
micro cracks do not affect much the structural integrity of PQC much.
Thus remedial works or repair of such cracks may not be necessary.
However, partial / half depth cracks should be repaired. About full
depth cracks and many checker cracks, it must be decided on the case
to case basis after looking at the site and analyzing the condition
depending upon its width, length and number of cracks in a panel as to
what treatment is to be given.
Repair Materials for Crack
The material, techniques / System for repair the PQC cracks should be such
which will have durability of minimum 10 – 15 years or as per the designed
life of pavement. Otherwise water may penetrate from these cracks and
reach sub-grade and embankment level causing settlement. This will
ultimately damage the pavement. Hence it is necessary that a methodology
and guidelines for the repairs & rehabilitation of such cracks in PQC be
developed. Normally the repair material should remain flexible enough to
accommodate anticipated expansion & contraction, water-tightness etc.
Repaired cracks should not be rigid otherwise the cracks may appear again
in the same panel at adjacent panels.
Following are some of the material used in crack repair.
1. Very Low Viscosity Epoxy Material
2. Epoxy Modified Mortar
3. Polyurethane based coating over Epoxy Mortar
4. Elastomeric Concrete
5. Fiber Reinforced Concrete.
Details of some of these materials are given here:
1. Very Low Viscosity Epoxy Material
It is a free flow epoxy grout material designed for grouting gaps of low
width like 0.5 to 10 mm. This epoxy repair compound or free flowing
epoxy resinous grouting material or similar product is a very low
viscosity liquid of around 10 poise or so. Epoxy compound like
RESICRETE of SWC or CONVEXTRA EP10 (M) of FORSROC which is
normally supplied as two-component product consisting of base and
hardener can be used. This should normally have viscosity of 2-4 poise
at ambient temperature. The Compressive strength of such material
should be at least 60-70 MPa or 1 ½ times the Compressive strength of
concrete used for PQC.
2. Epoxy Modified Mortar
Epoxy mortar is a common material used for repair of concrete
surfaces in general, especially for the pot holes in rigid pavements.
However, 100 % epoxy based mortar is little brittle in the long run;
hence in case of repairs of pavements, its modified products should be
used such that the resultant material is not rigid.
The Epoxy Mortar we can modified by:
o Adding about 5 % Poly-sulphide polymer in the epoxy resin as it
basically needs to modify the formulations of epoxy based
mortar. Many companies have started manufacturing Epoxy Poly-
sulphide mixed based mortar.
o It will not only improve the life of mortar but also it gives
flexibility which is required in the repair mortar used for the
pavements.
o By adding Poly-sulphide polymer, it improves the UV resistance.
3. Polyurethane based coating over Epoxy Mortar
As epoxy mortars are non-uv resistance, but still it is a good high
strength material, so use polyurethane based coating on the repaired
surface of mortar which is exposed to UV or direct sunlight. This
coating will protect the existence of epoxy mortar till the time the
mortar remain intact & not start to loose its property of non-brittleness.
PU coating should normally be of about 300 micron thickness.
4. Elastomeric Concrete
This is an epoxy modified cement concrete used in repairs not only in
PQC crack repairs but also in structures and concrete surface. For PQC
Crack repairs Elastomeric concrete is a useful material.
5. Fiber Reinforced Concrete
Fiber reinforced concrete is a concrete having small size aggregate
(say 6 mm or so) or Cement sand mortar. It is mixed with any one of
the different type of fiber given below which are generally used in
construction. Poly propylene Fibers are more appropriate for this
purpose. Though, there are several types of fibers available as given
below. Normally fiber concrete can also be used as a thin top layer or
bearing surface over the cracked PQC pavement after treatment of
cracks.
a. Steel Fibers
b. Carbon fibers
c. Glass Fibers
d. Poly propylene Fibers etc.
Repair Method of PQC in Pavements
Repairs can be classified into following categories:
a. Partial Depth repairs (Transverse as well as Longitudinal) of PQC.
b. Repairs of longitudinal cracks by using U type anchorages / stitching.
c. Repairs of the pavements especially for the areas where aggregates
are exposed due to various reasons like after concreting sudden rain
started or due to more tear & wear of concrete etc.
d. Re-surfacing of Pavements by Fiber Reinforced Concrete / Mortar for
betterment.
e. Cross Stitching / stapling of panels / cracks: Repair the cracks by
putting dowel bars with caps & tie bars so that it can have some space
to have movements.
f. Repairs of Potholes and corner spalls in concrete pavements etc
Repair of minor Cracks (<1 mm wide)
These are very low (small) width cracks or hairline cracks. Such cracks
generally do not affect the performance of road surface. Thus these cracks,
unless the severity level increases, need not be repaired. Further observe
these cracks over a period of time for enlargement.
Medium Cracks (generally 1 to 5 mm wide)
If cracks are not moving then a very low viscosity epoxy resin may be used
for its repair with or without fine sand to bond the crack faces. V shaped
‘joint wells’ are made with 3 to 5 mm saw blade. Also make 8 to 10 mm
diameter grout holes at regular interval. Then pump the epoxy bonded into
holes using a grout gun.
Partial Depth Repairs
The spalling of concrete occurs near the joints mainly due to adjacent slab
load transfer related movement at the joint particularly in summer. The
spalling will occur frequently in mid slab locations and other locations mainly
due to high slump due to w/c ratio, poor construction or failure of earlier
done repairs. Spalls are a localized problem and can be easily repaired with
partial depth repair methods.
Full Depth Repairs
The full depth repairs are necessitated due to Transverse Crack in slab in full
panel width. This crack may be in one lane or both the lanes. The reasons for
such crack are:
Locking of Transverse Joint:
The joint does not function due to non-functioning of dowel bars. These
dowel bars either get misaligned during construction or slurry gets into
sleeves and prevents their movement.
The intermediate crack may be caused due to too much resistance
offered by rough surface of underlying DLC.
The crack may also develop due to thermal changes coupled with large
joint spacing.
In all such cases where cracks are more harmful, then the PQC Panel should
be examined carefully, if the panel is to be repaired or removed. If it has to
be repaired than use the technique of cross stitching method. However, if
that portion of panel is to be removed and then recast the panel as indicated
by Removal of Existing Unsound Concrete.
Some of these repair methods are described here.
I. Repair By Grouting of Low Viscosity Epoxy Material
a. Equipments for Repair
Depending upon the method of repair the following equipments
may be used.
Grouting Pump of capacity about 5-10 Kg/cm2.
Mechanical Grout Mixer
Air Compressor
Injection Ports.
Hand Chisel, trowel, etc.
b. Preparation for Crack Repair
On both sides of crack, the side edges be slightly chiseled
to give a V-shape. If required do chiseling until a hard
concrete is encountered.
Remove loose material from crack area and blow out the dust and debris
from the gap of crack by using a compressor or air blower.
Figure 3: PQC crack showing
the Grout holes
Drill holes in PQC surface in the line of Crack upto depth of
about 150mm & 10 mm diameter @ 300 – 400 mm c/c as
shown in figure 3.
Fix Injection ports (Nipples) of plastic or similar material ie
nozzles of 6-8 mm in diameter and 100mm length into the holes
using appropriate gluing compound like Araldite. Keep the
projection of nozzle outside the PQC to about 20 mm.
c. Repair Procedure
Surface to be repaired may be pre wetted or bring it in SSD
condition.
Apply a coat of primer like acrylic bonding agent using
brush after scrubbing it well on the prepared surface. Allow
the primer to become tacky, which normally takes 10 – 15
minutes or as given in the manufacturer literature.
Push the Compressed air into the crack to flush out the
dust and all foreign material from the crack to the side or
top.
Fill the top of V-grove portion by appropriate Epoxy
modified mortar.
Use the epoxy repair compound or free flowing epoxy
resinous grouting material or similar product of very low
viscosity.
Prepare the mix of the repair material as directed by
manufacturer or Mix them mechanically with Grout mixture
after weighing them in recommended proportions.
Recommended water quantity (if water based) will be
measured and added to polymer component and mix it
thoroughly. The powder component will be mixed until a
homogeneous mix is obtained.
Pressure Inject the above material or appropriate ultra low
Viscosity epoxy liquid first in the middle nozzle from one
side of crack. Continue till it is forced out of next nozzle or
from the side of PQC crack. Then shift the injection
procedure to next nozzle.
After the injection is complete, estimate the consumption
of grouting material or find out the quantity of injected
material. This may be compared with the estimated
quantity.
If possible ask a supervisor from the suppliers of material
to supervise the job as per their recommended procedure
and specifications during the use of product.
Apply the mix within the pot life of repair compound on the
prepared crack.
d. Finishing of Repair Surface of Crack
If sagging on surface occurs during application to PQC
surface, then Polyurethane based coating may be applied
by trowel in smaller thickness in one or two layers.
The applied mortar shall be finished with wooden floats.
When the injection operation is over then cut the projected
portion of nozzles and sealing the portion by Epoxy Mortar.
After completion of repair of the joints, spalls, partial depth
repair, corner repairs, etc sealing of expansion joints
should be done immediately using polyurethane coating
otherwise joints might leak & will create problems in
future.
e. Curing of Repaired Surface
The repaired surface shall be cured by curing compound or
water curing, if required or as recommended by
manufacturer.
II. Repair By Stitching or Cross-stitching of Cracks
Cross-Stitching is a repair technique mostly used for longitudinal
cracks which are in reasonably good condition. The purpose of cross-
stitching is to maintain aggregate interlock and provide added
reinforcement for strength. The tie bars used in cross-stitching prevent
the crack from vertical and horizontal movement or widening. This
technique knits the cracked portions of the slab together and reduces
the chances of crack to grow further.
Cross-stitching uses deformed tie bars drilled across the crack at an
angle of 30-40 degrees. Deformed steel bars of 10-12 mm diameter
are sufficient to hold the crack tightly closed and enhance aggregate
interlock. Full depth holes of 18-20 mm diameter are drilled at a pitch
distance of 300 mm with offset of about 150 mm from the crack. The
holes are drilled alternately from each side of the crack so that it
passes through the crack from left to right, while the next from right to
left. After drilling, the holes are flushed with high pressure air to clean
out any residual dust. Then a high strength epoxy gel adhesive is
injected into the hole. Immediately after injecting epoxy, deformed
steel bars are inserted into each hole. The crack is sealed at the top
with silicon / epoxy modified sealant.
III. Removal / Replacement Of PQC Panel which has large cracks
When any one of the PQC panel has large number of cracks or if it is
settled, then concrete of such panel should be removed fully.
Otherwise ether it is very difficult to repair or it is too costly. In such
cases the following may be resorted:
a. Full panel removal and recasting as given below.
Removal of Existing Unsound Concrete
A minimum of 50 mm deep rectangular cut should be made at the end
of panel which is to be removed. Use saw cutting machine with vertical
faces. Inside this panel mark rectangle, smaller square of size 100 mm
× 100 m and 25-30 mm deep. These are marked to remove in parts.
The smaller square should be chipped off with chisel. If jack hammer is
used, it should not be more than 14 Kg. in weight. After removal of
unsound concrete, a reassurance hammer-striking is done and any left
out unsound area is also removed by enlarging the rectangle. If the
unsound concrete penetrates more than half depth of slab then full
depth of panel should be removed.
Breaking the Old Concrete
A saw cut usually as deep as possible is made to include all unsound
concrete. Once this cut (full depth or partial maximum depth) has been
made, about 100 mm deep cuts are made with circular diamond saw-
cutters. On the surface of cut-out slab some 75 mm × 75 mm or 100
mm × 100 mm square saw cuts are made to facilitate the breaking of
concrete by jack-hammer.
Recasting of Panel Concrete
Once the old concrete is removed the panel can be prepared for
recasting. A typical view is shown in figure 4. The PQC used for
recasting should be used should be of the same grade as of original
grade concrete. While recasting the panel, Dowel bars and tie bars
should be put in panel as shown in figure. Other procedures are as
used in original casting.
References
Jose C. Horta Report on Defects and Distress of Rigid Pavement
Sections: Survey, Rating, Monitoring, Causes and Repair By
Rev.TL.30.10.05
Binod Kumar, Dr. Saroi Gupta, Dr. V. K. Sood, 2004, Restoration
Techniques for Distressed Concrete Pavements, Technical Papers,
Seminar on Design Construction and Maintenance of Cement Concrete
Pavements, New Delhi, 8-10 October 2004, p. IV-101 to 110
Committee of State Road Authorities, Pretoria, South Africa, 1990,
Standard Nomenclature and Methods for Describing the Condition of
Jointed Concrete Pavements, Technical Recommendations for
Highways, Draft TRH19:1989, p. 1 - 49
D. C. De, S. K. Bagui, 2004, Approach to Maintenance of Concrete
Roads, Technical Papers, Seminar on Design Construction and
Maintenance of Cement Concrete Pavements, New Delhi, 8-10 October
2004, p. IVK-1 to 21
S. G. Joglekar, D. C. Saha, 2005, Defects, Repair and Rehabilitation of
Concrete Pavement, Seminar on High Speed Road Corridors, New
Delhi, 23 - 24 September 2007, p. 2:51 - 59
Satander Kumar, 2004, Causes of Distress, Repair end Maintenance of
Concrete Roads, Technical Papers, Seminar on Design Construction
and Maintenance of Cement Concrete Pavements, New Delhi, 8-10
October 2004, p. IV-2 to 14
Mohamed Y. Shahin, 1994, Pavement Management for Airports, Roads
and Parking Lots, Chapman & Hall, New York, London, 450 p.
Dr. V. M. Sharma, 2004, Diagnostic Investigations and Repair of
Cement Concrete Pavements - State of the Art, Technical Papers,
Seminar on Design Construction and Maintenance of Cement Concrete
Pavements, New Delhi, 8-10 October 2004, p. IV-133 to 144
Vikas V. Thakar, 2004, Maintenance and Rehabilitation of Cement
Concrete Pavements - State of the Art, Technical Papers, Seminar on
Design Construction and Maintenance of Cement Concrete Pavements,