-
-1-
INSTALLATION INSTRUCTIONS
MIRRORED CABINETK-13073T
( )MIRRORED CABINET W/DEFOGGER
K-13073T-D
MIRRORK-13079T
METALLIQUE
, 2010
Copyright Kohler China Ltd., 2010
BEFORE YOU BEGINBEFORE YOU BEGIN
�
�
�
�
Please read these instructions carefully to familiarizeyourself
with the required tools, materials, and installationsequences.
Follow the sections that pertain to yourparticular installation .
This will help you avoid costlymistakes. In addition to proper
installation, read alloperating and safety instructions.All
information in these instructions is based upon thelatest product
information available at the time ofpublication. Kohler China.
reserves the right to makechanges in product characteristics,
packaging, oravailability at any time without notice.These
instructions contain important care, cleaning, andwarranty
information-
Before installation carefully inspect the new fixture for
anysigns of damage.
Tempered glass cannot be cut.
Don't use acidic or alkalic cleaners oralcohol to clean the
wooden surface. Use a dampenedcloth to clean.
please leave instructions for the
consumer.
WARNING: Risk of injury or product damage.
WARNING:
�
�
�
�
-
PARTS
Parts supplied with your cabinet. (For cabinet body and
doorreplacement, call customer service with model number.) Besure
to check the cardboard supports in the carton, glassparts are
packed in them.
13-1 528437
1132363-T01-B
-
-2-
Mirrored Cabinet
ACCESSORIES LISTACCESSORIES LIST
Screws GB/T818-2000 S/S M4 12M4 12
X8
Screws ST3.5 35ST3.5 35
X4
Screws ST3.5 35ST3.5 35
X4
Side Mirrors
X2
Side Kits Brackets
X4
Wall Anchors
X4
Wall Anchors
X4
Snap-in Pins
X8
Mirror
K-13073T/K-13073T-D
ROUGHING-IN
UNIT : mm
489
762
129
99
Mirrored Cabinet
Caps of Screw
X4
Hole Plugs
X40
Foam Tape
X8
Top Clips
X2
431mm Mounting Bar431X1
Glass Shelves
X3
Half Sink-Screw S/S M3.5X10M3.5X10
X4
1132363-T01-B
-
-3-
K-13079T
INSTALLATION
NOTE
�
�
The cabinet has two ways of installation:
Recessing mounting.
Surface mounting.
Refer to the following instruction for mirror installation.
�
�
489
762
Mirror
STEP1
RECESSING THE MIRRORED CABINET INTO THE WALL
The Vertical installation changes the width of the roughout.
Please refer to the picture below.
468mm for Models468mm
Screws ST3.5 35ST3.5 35
745m
mhig
h745m
m
Fig. 1 1
1132363-T01-B
-
-4-
STEP2
Install screws through holes in mirrored cabinet as shown in
Fig.1, 2
DO NOT OVER- TIGHTEN!
Use s .
Note:
1 2
crews ST3.5 35
ST3.5 35
Fig. 2 2
Top View
Stud and wall surface
Install dome caps over screwsMirrored cabinet flange fits flush
against wall
SURFACE MOUNTING THE MIRRORED CABINET ON A WALL
NOTE:Installing the mirrored cabinet on a wall without the
doorattached can make installing easier for one person. Do notmount
the doors until the boxes is in or on the wall.
Fig. 3 3STEP
1
As shown in Fig 3, drill two 2- 5mm holes
in bottom mounting bar at indent location,
then drill 4- 6mm holes in wall at locations
shown in Fig 3, insert wall anchors.
3 5
4 6
Screws ST3.5 35 & Wall anchorST3.5 35
The highest point of table
Drill holes 2- 52- 5
Drill holes4- 6mm4- 6mm
Drill holes 2- 52- 5
Drill holes4- 6mm4- 6mm
20
750
320
1132363-T01-B
-
-5-1051705-T01-A
STEP3
Fig. 5 5
Apply foam tape to side kit bracket
DO NOT PEEL RELEASE LINER UNTIL YOU HAVE TEST FIT THE SIDE KITS
ON THE MIRRORED CABINET!
�
�
Peel tape from sheet, leave liner on.
Apply as shown to side kit brackets, be sure they are clean and
dry.
·
STEP2
Fig. 4 4
Top clips slide into this screwchannel from center opening.
Top of cabinet frame member
2 Top clips2
WA
LL
Sit the mirrored cabinet on the mounting bar, then lower and
tighten the
screws into place, as shown in Fig.4.
4
Screws ST3.5 35 & Wall anchorST3.5 35
Top clip forsurface mount2 per cabinet
1132363-T01-B
-
-6-
STEP4
STEP5
Fig. 6 6
Fig. 7 7
Fig. 8 8 Fig. 9 9
�
�
�
�
Attach the side kit brackets to the cabinet as shown
inFig.6.
Test fit the side kits, then clean the back of the side kitswith
rubbing alcohol.
Peel the release tape from the brackets and apply theside kits,
push firmly to set.
Cover the screw heads with the screw caps.
6 Align top of side kit with top of flange
Screws ST3.5 35self thread intoSide Kit brackets
2 pieces762mm high762
Side kit bracket(Fits tight under theflange of
mirroredcabinet)
( )
Side kit brackets
Door adjustments
�
�
�
7-A 8
7-B 9
( )
This screw releases the door from the cabinet and
allows up and down adjustment. Fig.7-A & 8.
These screws allow you to plumb the door as shown
in Fig.7-B & 9.
The screws you use for attaching the hinges.
(Supplied with hinges)
B
A
1132363-T01-B
-
-7-
STEP6
Push/twist the pins into place & Fill the remaining holes
with the plugs
�
�
Push one side of the shelf into the left or right clips.
Snap the shelf down into the opposite side. If the shelf is too
tight, repeat the process from the other side.
&
STEP7
A
B
Fig. 10 10 Fig. 11 11
Fig. 12 12
The step is only for the installation of defogger. See Fig
12,
external power supply.
(220V/50HZ)
220V/50HZ
1132363-T01-B
-
-8-
1.
2.
3.
4.
5. .
6. .
7.
USER MAINTENANCEUSER MAINTENANCE
Warn! Risk of product damage.
1.
2.
3.
4.
5. The mirrored cabinet door and interior are constructed
ofmirror and aluminum. Use only a damp cloth to clean.Spray the
cloth, not the mirror when cleaning. Mirrors aredamaged by the use
of ammonia or vinegar basedcleaners. Rubbing alcohol can be used
for stubborn stains
6. Use no abrasive cleansers on any part of the
mirroredcabinet.
7. The white frame should be cleaned with a damp cloth only.
Many cleansers contain abrasive and chemical substancewhich is
not suitable for cleaning stainless steel, enamel,plating or
plastic products. You may use mild cleansers orsoaps to clean the
surfaces. Wipe any splashes of cleanersolutions from the surface
with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dryarea
from the damp one if conditions permit. Try to openthe door and
windows of the bathroom and maintain goodventilation.
Kohler mirrored cabinet are dealt with strict procedures
fordamp-proof, whose good damp-proof function ensuresgood
performance even in bathroom of huge humidity. Yetdo not splash and
pour water directly on the mirroredcabinet. Make sure that the
bathroom is not over dampand wipe any splashes from surfaces
immediately.
Maintenance of door board: Clean and wipe door boardregularly,
and wipe the condensation vapor with dry andsoft cloth.
.
MIRROR
Fig. 13 13 STEP1
See Fig.12, drill holes on the wall insert the wall
anchors, fix the wall bracket of mirror and then
hang the mirror to the bracket.
12
Screws ST3.5 35 & Wall anchorST3.5 35
Drill holes4- 6mm4- 6mm
500
388
1132363-T01-B
/ColorImageDict > /JPEG2000ColorACSImageDict >
/JPEG2000ColorImageDict > /AntiAliasGrayImages false
/CropGrayImages true /GrayImageMinResolution 300
/GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true
/GrayImageDownsampleType /Bicubic /GrayImageResolution 300
/GrayImageDepth -1 /GrayImageMinDownsampleDepth 2
/GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true
/GrayImageFilter /DCTEncode /AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict >
/GrayImageDict > /JPEG2000GrayACSImageDict >
/JPEG2000GrayImageDict > /AntiAliasMonoImages false
/CropMonoImages true /MonoImageMinResolution 1200
/MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true
/MonoImageDownsampleType /Bicubic /MonoImageResolution 1200
/MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000
/EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode
/MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None
] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000
0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier ()
/PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped
/False
/Description > /Namespace [ (Adobe) (Common) (1.0) ]
/OtherNamespaces [ > /FormElements false /GenerateStructure true
/IncludeBookmarks false /IncludeHyperlinks false
/IncludeInteractive false /IncludeLayers false /IncludeProfiles
true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe)
(CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA
/PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged
/UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false
>> ]>> setdistillerparams> setpagedevice