Memory interface Memory is a device to store data To interfacing with memories, there must be: address bus, data bus and control (chip enable, output enable) To study memory interface, we must learn how to connect memory chips to the microprocessor and how to write/read data from the memory Different kinds of memory chips will also be introduced
93
Embed
Memory interface Memory is a device to store data To interfacing with memories, there must be: address bus, data bus and control (chip enable, output enable)
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Memory interface Memory is a device to store data
To interfacing with memories, there must be: address bus, data bus and control (chip enable, output enable)To study memory interface, we must learn how to connect memory chips to the microprocessor and how to write/read data from the memoryDifferent kinds of memory chips will also be introduced
Memory• Knowing memory is becoming more important • Your mobile devices do not have a harddisk but
they have memory • IPad or other tablet computer has no harddisk!
– But still very powerful!• Latest trend SSD (solid state drive) – a data
storage device that uses solid-state memory to store data similar to a traditional harddisk
• SSD is now rather expensive – A 64GB SSD is in the range HKD1000
Block diagram of a memory interface
Data
0000
FFFFAddress in Hex
Control signalsInclude enable (chip select), read/write
Content
Self-test
Memory capacity No. of address lines
128K ?
16M ?
14M ?
Introduction• For the 8086 microprocessor, there are two
modes: minimum and maximum• Under different modes, the memory interface is
not the same• In the minimum mode, 8086 processor is
connected to the external memory block directly• In the maximum mode, a Bus controller is needed• The bus controller will issue the required control
signal to drive the memory block
Minimum Mode
8086 memory
A16-A19
AD0-AD15
/DENDT//RM/IO/WR/RD
ALE
/BHE
Address space and data organization• Memory is organized as 8-bit bytes (byte as the
basic unit)• To address a word then 2 consecutive bytes are
used, lower addressed byte is the LSB (Least Significant Byte) and the higher-addressed byte is the MSB (Most Significant Byte)
• Words of data can be stored at even, or odd address boundaries
MSB LSB
16-bit
Memory addressing• The address bit A0 of the LSB can be used to
determine the address boundary. If A0 is 0 then we have an even address, or aligned
• If A0 is odd then we have odd-boundary
• Example: 0001H is an odd-boundary address
Example• A0 = 1 example
– A 16-bit data store at 01FFFH (then it is not aligned) and will occupy 01FFFH and 02000H (Odd boundary)
• A0 = 0 example– A 16-bit data store at 02002H (then it is
aligned) and will occupy 02002H and 02003H (even boundary)
Question• If you are asked to implement the memory
system for a 8086 microprocessor, what memory configuration will you use?
A) One 1M Bytes chip
B) Two 512KBytes chips
C) One 1M Word chip
Address Space• Even-boundary data can be accessed in one
bus cycle• Odd-boundary word must be accessed in
two bus cycle• In 8086, user’s data usually is in 8-bit or
16-bit format• For the system, instructions are always
accessed as words (16-bit)• There is also double word format (32-bit)
Data type• Double word (32-bit) will be stored in 4
consecutive locations• When double word is used?
– Double word can be used as a pointer that is used to address data or code outside the current segment
– For a double word, the higher WORD stores the segment address, the lower WORD stores the offset
Memory organization
BHE – bank high enable
Odd boundaryAddress requires2 cycles
1M bytes memory using 2 512K byte chips
Hardware organization• In hardware, the 1M bytes memory is implemented as
two independent 512K-byte banks• Low (even) bank, and the high (odd) bank• Data from low bank use data bus 0-7• Data from high bank use data bus 8-15• Signal A0 enables the low bank • Signal /BHE enables the high bank • /BHE is active low• How many address lines are required in order to access
512K locations? (Ans. 19)
Memory organization
High bank Low bank
Only A1 to A19 are used to drive the memory !!!
Odd-addressed word transferNeed two cycles!
Odd address such as 1233H (low byte) + 1234H (high byte)
Example• Consider the 16-bit word stored at 01FFFH then it
occupy 01FFFH and 02000H• In the first cycle data in 01FFFH will be read• In the second cycle data in 02000H will be read• Second case data stored in 02002H then data
occupy 02002H and 02003H. Compare the bit pattern for 02002H and 02003H
• 02002H – 0000 0010 0000 0000 0010 • 02003H – 0000 0010 0000 0000 0011• Why both byte can be read in a single cycle?
Dedicated Memory locations
Dedicated memory locations should not be usedas general memory space for data and program storageFor the 8086, address 00000 to 0007F and FFFF0 to FFFFB are dedicatedAddress from FFFFC to FFFFF are reserved
ExerciseDetermine the values for A0 and /BHE in order to accessA byte at even address (/A0=0, /BHE = 1)A byte at odd address (/A0=1, /BHE = 0)A word at even address (aligned) (/A0=0, /BHE=0)A word at odd address (unaligned), as shown in the following figure(two cycles:First cycle get LSB /A0=1 /BHE=0Second cycle get MSB /A0=0 /BHE =1)
Memory control signals• To control the memory system in the minimum
mode, requires: ALE, /BHE, M/IO, DT/R, /RD, /WR, and /DEN
• ALE – address latch enable, signals external circuitry that a valid address is on the bus (0->1) so the address can be stored in the latch (or buffer)
• M/IO – identify whether it is a memory or IO (Input/Output) operation (high – memory, low – I/O)
• DT/R – transmit or receive (1 – transmit)• DEN – to enable the data bus
Read cycle of 8086• Consists of 4 time states• T1 – memory address is on the address bus, /BHE
is also output, ALE is enable • Address is latch to external device at the trailing
edge of ALE• T2 – M/IO and DT/R are set to 1 and 0
respectively. These signals remain their status during the cycle
• Late in T2 - /RD is switched to 0 and /DEN also set to 0
Read cycle
• T3 and T4 – status bits S3, S4 are output
• Data are read during T3
• /RD and /DEN return to 1 at T4
Read Cycle
Write cycle• T1 – address and /BHE are output and
latched with ALE pulse
• M/IO is set to 1, DT/R is also set to 1
• T2 - /WR set to 0 and data put on data bus
• Data remain in the data bus until /WR returns to 1
• When /WR returns to 1 at T4, data is written into memory
Write Cycle
Example
• What is the duration of the bus cycle in the 8086-based microcomputer if the clock is 8MHz and two wait states are inserted
Ans. 750ns (6 cycles) where each clock is 125ns
Demultiplexing the address/data bus
• Address and data must be available at the same time when data are to be transferred over the bus
• Address and data must be separated using external demultiplexing circuits (eg a latch, or buffer)
• Address are latched into external circuits by ALE (address latch enable ) at T1
Demultiplexing the system bus
Bi-direction
One direction
Latches/buffersSTB - Strobe
Syntax to describe a memory
• Memory is usually described by its size of storage and number of data bits
• Eg. A 32K bytes memory chip is represented by 32Kx8
• A 32K bits memory is represented by 32Kx1
Configurations of memory for 16-bit data
Chip enable (CE) usually generated by some decoding mechanismOE – output enable
Simple maths• From 00000H to FFFFFH there are 1M memory
locations• How about from 0000H to FFFFH?• How many locations between 1FFFFFH to
310000H (answer in terms of M + K and Byte)• A memory system has 4M locations and the
starting address is 420000H what is the ending address?
Memory
• Read only memory (ROM) – nonvolatile • Data remains when power is turned off, data are
written into the ROM during its fabrication at the factory
• PROM- Programmable ROM. Can be programmed by user but this can only be done once
• EPROM – erasable programmable ROM• Contents of EPROM can be erased by exposing it to
ultraviolet light• EEPROM – Electrical Erasable PROM (your USB
memory stick)
Exercise
• There is a BIOS in your computer, what kind of memory is it?
Block diagram of a ROM
ROM interface – address input, data output, /CE – chip enable, /OE – output enable (for READ operation)
Memory Read Operation• To read a ROM, we need to issue the proper
address• There is a delay between address inputs and data
outputs• The access time (tACC), chip enable time (tCE), and
chip deselect time (tDF) are important timing properties
• You need these information for developing a real computer system
Timing parameters
• The access time – delay occurs before data stored at the addressed location are stable at the outputs (ie how long it takes to access data). The microprocessor must wait for tACC before reading the data
ROM read operation
• Access time is regarded as address to output delay. Typical value is 250ns
• tCE – represents the Chip Enable to output delay, usually this is equal to access time
• Deselect time – amount of time the device takes for data outputs to return to high-Z state after /OE becomes inactive
Read operation tAA=access time tCO= chip select to output delaytHZ = deselect to output float
Question• A normal 8086 read cycle takes 4 clocks• For a system with a 8MHz clock• Now you are required to develop the
memory system for the computer which of the following devices will you use?
1. Tacc = 0.125us $100
2. Tacc = 0.2us $50
3. Tacc = 0.4us $20
Choosing the proper memory
Configuration of ROM for 8-bit bus
How the circuitoperates?
EEPROM – electrical Erasable ROM
• Data stored in an EEPROM can be erased electrically
• Example inside the AduC832 (or 8051) microcontroller, there are 64KBytes of EEPROM
Programming the EPROM
• In an erased EPROM, all cells hold logic 1• Vpp is in logic 1 for data to be read from EPROM• Vpp is ON (eg Vpp = 25V for 2716 EPROM) for
programming mode (writing)• 2716 is a 2Kx8 EPROM• To write data to the EPROM a 25V signal is
Write-cycle for SRAM• To write, we must produce the signal in proper
order• Minimum duration of a write cycle is tWC (write
cycle time )• Address must remain stable during the whole
cycle• Chip enable (CE) signal becomes active• The Write Enable (WE) will be active after the
address setup time tAS elapses
RAM write operation• Data should now ready and must be valid
for tDW (data valid to end of write)
• Data should remain valid (tDH) after the write
• A short recovery period (tWR) takes place after /WE returns to 1 before the write cycle is complete (address is removed)
Write cycle
Timing parameters for a write cycle
Parameter Time (ns)
Tc (rd) read cycle time 120
TWC (wr) write cycle time 120
TWP write pulse width 60
Tsu (A) address set up time 20
Tsu (S) chip select setup time 60
Tsu (D) data setup time 50
Th address hold time 0
Th (D) data hold time 5
Read Cycle• Read cycle for RAM is similar to the ROM• Minimum duration of a read cycle is tRC (read
cycle time)• Address must remain stable during the whole
cycle• Chip enable becomes active• The Enable(s) (CE) will be active after the address
is stable• Data should now ready • Data should remain valid after the OE and CE
have been removed
Read CycleCO – time betweenValid data and chip enable
OE – time betweenValid data and output enable
DRAM
• DRAM has a higher density
• Cost less
• Consume less power
• Take up less space
• We can get 64Mx1, 128Mx1 modules
DRAM
• An example of a DRAM – 2164B
• It is a 64K-bit (64Kx1) device with only 16 pins
• To address 64K address, requires 16-bit address line
• 16-bit address is divided into two separate parts: 8-bit row address, and 8-bit column address. And these are time-multiplexed
DRAM-2164B
Address bus is time multiplexedRAS – row address strobeCAS – column address strobe
Addressing the DRAM• The row address is first applied • /RAS is pulsed to ‘0’ to latch the address into the
device• The column address is applied and /CAS strobed
to ‘0’• If RAS is left at ‘0’ after the row address is
latched inside the device, the address is maintained within the device
DRAM• Data cells along the selected row can be
accessed by simply supplying successive column addresses
• This is called page mode accesses
• (How many bits are there in a row?)
• Advantage - faster access of memory is achieved
Addressing the DRAM-64Kx16 setup
Refreshing the DRAM
• The DRAM must be refreshed every 2ms
• Refreshing is achieved by cycling through the row addresses (i.e. generating all the row address)
• During refreshing, /CAS is at logic ‘1’ and no data are output
Example 416800 DRAM • The 416800 DRAM is 2Mx8 device and the data
is parallel (8-bit) but address is multiplexed divided into ROW and Column.
• In order to access 2M memory locations, it takes 21 address bits. In the device, the address lines are multiplexed into: 12 address lines for row address and column address is only 9-bit.
• The refresh must be done in every 64ms.
416800 DRAM
System memory configuration
Memory configuration for ADuC832
ADuC832 memory architecture
Address Decoding• Address decoding is required because many memory chips
are used by a computer system• At each memory read/write only a number of chips is used • Decoding mechanism is used to guarantee that the proper
chips are selected• Certainly, capacity of modern memory device is large
(GB!!) so decoding may not be necessary but if you consider the development of SSD then decoding will become necessary if a SSD is 250G then you still need to use more than 1 memory device
Address decoding
• To design, first determine the number of chips required
• Then determine how many address lines are needed for the decoding purpose
• Example if 4 chips are used then you need 2 address lines for decoding
Example
For 8086 system, max. 1M bytes of memory Now we use 4 256Kx8 memory chip.Note:Even addresses memory locations should be in the same chipOdd addresses memory locations should be in the same chip
So the 4 memory chips will be divided into Even and Odd group (two chips per group)Only consider the even group, since the chip is only 256K so the Memory locations stored by one chip is from 00000 to 7FFFF (with only the even locations)The other chip holds 80000 to FFFFF (only the even locations)
Example
Address80000 to FFFFF
Address00000 to 7FFFF
Odd Even
Now if the address issued is 12345H which memory chip shouldbe selected?What address line(s) can be used for the decoding ?
Decoding system
Decoder
Memories
Memories
Address lines used for driving the memories
AddressUsed for Selecting The memoryblock
Outputs from decoderusually used as /CE for the memories
Decoder
Inputs Outputs
Any device that can relateits output to its inputs can beused as a decoderOutput = f(inputs)
Address Chip enable (/CE)
Decoding• Based on the previous example
– The decoding address line is A19
– A19 = 0 then select addresses from 00000H – 7FFFFH
– A19=1 then select addresses from 80000H – FFFFFH
– A0 and BHE are used to select the even and odd
• Can you identify a device that can be used for decoding?
Decoding
A19
/CE of 00000H – 7FFFFH
/CE of 80000H – FFFFFH
What is this?
Decoder
Address Decoding Techniques
• An address decoder is a circuit that examines the address lines and enables the memory (producing the /CE signals) for a specified range of addresses. This is vital in any memory design because one block of memory must not be allowed to overlap another.
• Logic Gate Decoders (ANDS, ORS, NANDS, AND NORS).
Address Decoder circuits
• A digital decoder is a circuit that recognizes a particular binary pattern on its input lines and produces an active output indication.
When will you get an active memory select?Ans. When all inputs are 0s then the output is 0
NAND Gate Decoder Circuit
Output of the NAND gate is active when all inputs are 1s so The address from A19 to A11 is 111111111 (FF8)From A0 to A10 is used to address the memory chip
Logic gates as decoder
• A logic gate only comes with one output so if your system has many memory chips then you need one gate per memory chip!!!!!!
The 3-to-8 Line Decoder (74LS138)• The truth table shows that only one of the
eight outputs ever goes low at any time. Three enable inputs /G2A,/G2B, and G1 must all be active.
• Once the 74LS138 is enabled, the address inputs A,B, and C select which output pin goes low.– Remarks: / means logic low (0) signal level.
Truth Table for 74LS138 Decoder
AddressLines willConnect To A, B and C
64KByte Memory Bank Circuit
To enable the decoder, the NAND output (connected to G2B) must be 0 therefore A19 to A17 must be 111. The G1 input must be 1 so A16 is 1 so address lines A19 to A16 must be 1111 (F)
Example-128 MB Memory Circuit
Example-128 MB Memory Circuit (Cont’d)
BE – Bank Enable There are 4 banks to support data in byte, word and double word
How to design a decoding systemDesign a memory system for a 8086 based computerUsing 64K byte memory chips.
To design the memory system, we must first identify the followings:
How many address lines for the 64Kbyte chip?How many chips are needed for the 8086 system?Determine the address ranges for each memory blockDetermine the number of address lines can be used for decodingIdentify a suitable decoderDraw the block diagram
Example
How many address lines for the 64Kbyte chip?16-bitHow many chips are needed for the 8086 system?8086 system can address 1M so 16 chips are neededThe system should be divided into Even address and Odd addressEven address enabled by A0, Odd address enabled by BHE8 chips will be used for the even address and a decoder can be used
Decoding• 16 memory chips become 8
groups • Each group includes 2 devices
(even + odd)• Each group includes 128K
memory locations• Assign addresses represented
by each group • Look for common bit pattern
within addresses of the same group
• The common bits will be used for decoding
Common bits group Address range
A19A18A17
111
7 20000H-
3FFFFH
A19A18A17
110
6 20000H-
3FFFFH
A19A18A17
1 0 1
5 20000H-
3FFFFH
A19A18A17
100
4 20000H-
3FFFFH
A19A18A17
0 11
3 20000H-
3FFFFH
A19A18A17
0 10
2 20000H-
3FFFFH
A19A18A17
0 0 1
1 20000H-
3FFFFH
A19A18A17
0 0 0
0 00000H-
1FFFFH
Self test• How many bytes can be stored by a 32Kx4 memory chip? (Ans. 16K bytes)• How many 16K bytes memory chips are required to form a 1M system? (Ans.
1M/16K = 64)• How many address lines are required to address a 16K bytes memory ? (Ans.
14) • Why the signal ALE is necessary for a 8086 microprocessor? (Ans. Because
the address bus is multiplexed)• Why memory decoding is necessary for a computer system? (Ans. To select
the proper memory chips when an address is issued)• What is High-block, Low-block? (High-block represents the odd memory
address, low-block is the even addresses )• The two address range F8000-F8FFF and FA000-FAFFF can be decoded by
what address bit(s)? (Ans. Must first examine the binary pattern of the addresses. F8000-F8FFF = 11111000 (for the first two digits) FA000 – FAFFF is 11111010 (for the first two digits) so the difference between the two ranges is bit A14. Therefore, A14 can be used to decode the two ranges. )
Exercise• Develop a 16-bit wide memory interface that
contains ROM memory at locations 000000H – 01FFFFH for the 80386SX microprocessor.
• A 386SX microprocessor has 24-bit address• The ROM used is 32Kx8 • The decoding logic should output signal to select
the chip (/CS) • Select a proper decoding device (eg multiplexer,
PAL, simple logic gates )
Exercise• Develop a 16-bit wide memory interface that contains
SRAM memory at locations 200000H – 21FFFFH for the 80386SX microprocessor. (total of 128K bytes)
• A 386SX microprocessor has 24-bit address• The SRAM used is 32Kx8 (so you need 4 memory chips)• The decoding logic should output signal to select the
chip (CS) , as well as enable the write operation (WE)• Select a proper decoding device (eg multiplexer, PAL,
simple logic gates )• You can refer to Figure 10-32
Serial EEPROM
• If building a simple device and memory is needed to store data nowadays, most commonly used memory device is serial EEPROM
• As the number of pins to connect to the device is small
Serial EEPROM• Clock and data transitions:• Data on the SDA pin may change only during SCL low time periods.
Data changes during SCL high periods will indicate a start or stop condition.
• Start condition: • A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command• Stop condition:• A low-to-high transition of SDA with SCL high is a stop condition.
After a read sequence, the stop command will place the EEPROM in a standby power mode.
• Acknowledge:• The EEPROM sends a zero during the ninth clock cycle to