Mediatrix 4400 Digital Gateway ISDN Telephones€¦ · Mediatrix 4400 Digital Gateway ISDN ... are used to power the Mediatrix unit at the circuit breaker ... 4400 Digital Gateway

Mediatrix 4400 Digital Gateway ISDN Telephones

Mediatrix 4400

Revision 285

2011-06-22

Table of Contents

media5corp.com

Table of Contents

Mediatrix 4400 Digital Gateway ISDN Telephones 3

Requirements 5

Configuration of the Mediatrix 4400 Digital Gateway 6

Using IPv4 to Connect the Mediatrix unit to a Network with a DHCP 6Using IPv4 to Connect the Mediatrix Unit to a Network without a DHCP 7Logging On to the Mediatrix Unit Web Interface 8Configuring the Default Servers 9Registering a Unit to All Gateways 10Configuring ISDN 11Restarting Services 11Creating a Route From Sip-default to ISDN 12Creating a Route From ISDN to SipDefault 13

Validation 14

Performing a Basic Call - Scenario A 14Performing a Basic Call - Scenario B 14

Available Documentation 15

Copyright Notice 16


media5corp.com

Mediatrix 4400 Digital Gateway ISDN TelephonesThis document outlines the configuration steps to set up one Mediatrix 4402 digital gateway toprovide voice over IP (VoIP) connectivity to ISDN telephones in a corporate network environment.

The Mediatrix 4402 is used to connect the ISDN telephones to an existing VoIP network. Theconfiguration starts with the Mediatrix 4402 default configuration, but can be easily customized forthe 4404 and 4401. From now on, the device will be referred to as the Mediatrix 4400.

The steps described in the following pages will show you how to setup the Mediatrix unit so it can:• Receive calls from the ISDN phones and route them to a remote branch through the VoIP

network (e.g. from Office A to Office B)# A user from Office A picks up an ISDN phone and dials a number.

# The Mediatrix 4400 forwards the call to the appropriate Mediatrix 1102.

# The Mediatrix 1102 makes the appropriate analog phone ring.

# A user in Office B picks up the analog phone and the call is established.

• Receive calls from remote branches through the VoIP network and route them on one of thelocal branch's ISDN phones (e.g. from Office B to Office A)# A user from Office B picks up an analog phone and dials a number.

# The appropriate Mediatrix 1102 routes the call to the Mediatrix 4400.

# The Mediatrix 4400 decides to which ISDN BRI interface route this call (based on diallednumber).

# The appropriate ISDN phone rings.

# A user from Office A picks up the ISDN phone and the call is established.


media5corp.com


media5corp.com

Requirements

• The phone numbers of the ISDN phones in Office A correspond to registered users in the SIPserver (without authentication).

• The Office B setup is functional, and the SIP users are correctly registered to the SIP server.


media5corp.com

Configuration of the Mediatrix 4400 DigitalGateway

Using IPv4 to Connect the Mediatrix unit to a Network with a DHCP

Before you start• Make sure that your network connection is working.

• If your unit does not have an FXS port, or if you do not have access to the DHCP server's logs,then use the Using IPv4 to Connect the Mediatrix Unit to a Network without a DHCP (p. 7) procedure.

Steps1) Wear an ESD wrist strap, ensuring it makes good contact with your bare skin.2) Attach the ESD wrist strap end to an earth ground (unpainted bare metal spot of a grounded

equipment rack).3) Make sure the circuit breakers of AC power sources used to power the Mediatrix unit are

OFF.4) Make sure the provided external Power Adaptor is connected to the DC connector of the

Mediatrix unit and in an appropriate AC electrical outlet.5) Connect a 10/100 BaseT Ethernet RJ-45 cable into the ETH1WAN connector of the Mediatrix

unit.6) Connect the other end of the cable to a router/switch connected to your Network.7) Validate the installation.8) Turn ON the AC power sources that are used to power the Mediatrix unit at the circuit

breaker

Note: When the unit is brought from a cold to a warm environment, condensation, thatmight be harmful to the unit, may occur. If this is the case, wait one hour before connectingthe power cord.

9) If you have an FXS port, dial *#*0 to get the IP address or consult the DHCP server's logsto find out your IP address.


media5corp.com

ResultThe Power LED on the unit will be flashing when the unit performs a DHCP query. It will becomesolid once it successfully gets an IP address from the DHCP server. At this point, you can now usethe DHCP IP address to access your unit's management interface.

Next StepLogging On to the Mediatrix Unit Web Interface (p. 8)

Using IPv4 to Connect the Mediatrix Unit to a Network without aDHCP

Before you start• Your computer must be set to use the 192.168.0.11 private IP address.

• Make sure that your network connection is working.

Steps1) Wear an ESD wrist strap, ensuring it makes good contact with your bare skin.2) Attach the ESD wrist strap end to an earth ground (unpainted bare metal spot of a grounded

equipment rack).3) Make sure the circuit breakers of AC power sources used to power the Mediatrix unit are

OFF.4) Make sure the provided external Power Adaptor is connected to the DC connector of the

Mediatrix unit and in an appropriate AC electrical outlet.5) Connect a 10/100 BaseT Ethernet RJ-45 cable into the ETH2LAN Ethernet connector of the

Mediatrix unit.6) Connect the other end of the cable into your PC.7) Validate the installation.8) Turn ON the AC power sources that are used to power the Mediatrix unit at the circuit

breaker.

Note: When the unit is brought from a cold to a warm environment, condensation, thatmight be harmful to the unit, may occur. If this is the case, wait one hour before connectingthe power cord.


media5corp.com

ResultYou can now use the 192.168.0.10 IP address to access your unit's management interface.

Next StepLogging On to the Mediatrix Unit Web Interface (p. 8)

Logging On to the Mediatrix Unit Web Interface

InformationFor better performances, it is recommended to use the latest available version of Microsoft InternetExplorer, Google Chrome or Mozilla Firefox.

Note: You may not be able to log on to the Management Interface if you are using older browserversions. The computer's network card must be on the same subnet as the Mediatrix unit.

Steps1) In your web browser, enter the IP address used by your Mediatrix unit to communicate with

the Management Interface.• If your computer is connected to the Ethernet port, commonly used to be connected

to the Local Area Network (LAN), i.e. ETH2 on most devices, use the 192.168.0.10 IPaddress.

• If your Mediatrix unit is configured to use a DHCP with IPv4, use the DHCP- provided IPaddress.

2) Enter public as your username and leave the password field empty.

Note: The public username account has administrator rights.

Note: You can also use admin as a username and administrator as password.

3) Click Login.


media5corp.com

ResultThe Information page of the Management Interface is displayed.

Next StepConfiguring the Default Servers (p. 9)

Configuring the Default Servers

Before you startIf you are not familiar with the meaning of the fields, click Show Help, located at the upper rightcorner of the Web page, to display field description when hovering over the field name.

InformationIn some instances, the configuration of the default servers may already be completed.

Steps1) Go to SIP>Servers.2) In the Registrar Host field, indicate the server IP address or FQDN to use for this gateway.3) In the Proxy Host field, indicate the server IP address or FQDN to use for this gateway.4) In the Messaging Server Host field, indicate the server IP address or FQDN to use for this

gateway, if needed.5) Leave the Outbound Proxy Host field empty unless specifically instructed to set a value.

Note: Setting the address to 0.0.0.0:0 or leaving the field empty disables the outboundproxy host.

6) Click Apply.7) Click Restart required services located at the top of the page.

Result


media5corp.com

Next StepRegistering a Unit to All Gateways (p. 10)

Registering a Unit to All Gateways

Before you startIf you are not familiar with the meaning of the fields, click Show Help, located at the upper rightcorner of the Web page, to display field description when hovering over the field name.

Steps1) Go to SIP> Registrations.2) In the Unit Registration table, enter in the User Name, a username to uniquely identify

the user in the domain.3) From the Gateway Name selection list, choose the Sip gateway the user will be assigned to.4) Click Apply and Refresh.5) Click Restart required services located at the top of the page.

ResultThe information will be displayed in the Unit Registration Status table.


media5corp.com

Next StepConfiguring ISDN (p. 11)

Configuring ISDN

InformationIf you are not familiar with the meaning of the fields, click Show Help, located at the upper rightcorner of the Web page, to display field description when hovering over the field name.

Steps1) Go to ISDN > Primary Rate Interface.2) From the Select Interface dropbox, select the interface for which you want to make

modifications.

Note: Depending on the Mediatrix's model, there may several interfaces.

3) In the Interface Configuration table, set the Endpoint Type to NT.4) Leave all the other parameters to their default values.5) Click Apply.6) Repeat the tasks 2 to 5 for each interfaces.

Next StepRestarting Services (p. 11)

Restarting Services


Steps1) Go to System > Services.2) In the Restart required services table, click Restart required services.


media5corp.com

Next StepCreating a Route From Sip-default to ISDN (p. 12)

Creating a Route From Sip-default to ISDN


Steps1) Go to Call Router > Route Config.2) In the Route table

• click located on the same row as an existing route to add a route above or,

• click located at the bottom of the table to add a route at the end of the table.

3) Set the Sources field to sip-default.4) Set the Destination field to isdn-Bri1.5) Set the Properties Criteria field to Called E164.6) Using the dropbox, set the Expression Criteria to correspond to your situation.

Note: This route forwards all incoming SIP calls to the ISDN BR1 interface if the dialednumber (E164) starts with the digit you configured in the Expression Criteria field.

7) Click Save.8) Repeat the tasks 2 to 7 to create an additional route from sip-default to isdn-Bri2.

Result


media5corp.com

Next StepCreating a Route From ISDN to SipDefault (p. 13)

Creating a Route From ISDN to SipDefault


Steps1) Go to Call Router > Route Config.2) In the Route table

• click located on the same row as an existing route to add a route above or,

• click located at the bottom of the table to add a route at the end of the table.

3) Set the Sources field to isdn-Bri1.4) Set the Destination field to sip-default.5) Leave the other fields empty.6) Click on Save.7) Repeat the tasks 2 to 7 for the routes.

Result

Next StepPerforming a Basic Call - Scenario A (p. 14)


media5corp.com

Validation

Performing a Basic Call - Scenario A

Steps1) Pickup Phone A .2) Dial Phone B's number.3) Phone B rings4) Pickup Phone B.

ResultThe call is established.

Next StepPerforming a Basic Call - Scenario B (p. 14)

Performing a Basic Call - Scenario B

Steps1) Pickup Phone B.2) Dial Phone A's number..3) Phone A rings.4) Pickup Phone A..

ResultThe call is established.


media5corp.com

Available Documentation

For more details, refer to the Mediatrix Documentation.

https://documentation.media5corp.com


media5corp.com

Copyright NoticeCopyright © 2016 Media5 Corporation.

This document contains information that is proprietary to Media5 Corporation.

Media5 Corporation reserves all rights to this document as well as to the Intellectual Property ofthe document and the technology and know-how that it includes and represents.

This publication cannot be reproduced, neither in whole nor in part, in any form whatsoever, withoutwritten prior approval by Media5 Corporation.

Media5 Corporation reserves the right to revise this publication and make changes at any time andwithout the obligation to notify any person and/or entity of such revisions and/or changes.

Mediatrix 4400 Digital Gateway ISDN Telephones€¦ · Mediatrix 4400 Digital Gateway ISDN ... are used to power the Mediatrix unit at the circuit breaker ... 4400 Digital Gateway

Documents