MECHANICAL TECHNOLOGY MEGANIESE TEGNOLOGIE FITTING ...

P a g e | 1

Mechanical Technology Grade 8 30/03/2021

MECHANICAL TECHNOLOGY MEGANIESE TEGNOLOGIE

FITTING & MACHINING PAS- & MASJIENWERK

GRADE / GRAAD 8

FORMAL ASSESSMENT TERM 1 DATE / DATUM: 30 MARCH 2021 TIME / TYD: 20 MINUTES / MINUTE TOTAL / TOTAAL: 20 MARKS / PUNTE EXAMINER EKSAMINATOR: MR. C. DE WAAL MODERATOR: MR. G. VENTER DISTRICT DISTRIK: D2 – GAUTENG – WEST / WES

P a g e | 2

Mechanical Technology Grade 8 30/03/2021

INSTRUCTIONS AND INFORMATION / INSTRUKSIES EN INLIGTING

1. This question paper consists of FIVE questions. Hierdie vraestel bestaan uit VYF vrae.

2. Read ALL the questions carefully. Lees AL die vrae deeglik.

3. Answer ALL the questions. Beantwoord AL die vrae.

4. Number the answers correctly according to the numbering system used in this question paper.

Nommer die antwoorde korrek volgens die nommeringstelsel wat in hierdie vraestel gebruik is.

5. Start EACH question on a NEW page. Begin ELKE vraag op 'n NUWE bladsy.

6. Show ALL calculations and units. Round off final answers to TWO decimal places. Toon ALLE berekeninge en eenhede. Rond finale antwoorde tot TWEE desimale plekke af.

7. Candidates may use non-programmable scientific calculators and drawing instruments.

Kandidate mag nie-programmeerbare wetenskaplike sakrekenaars en tekeninstrumente gebruik.

8. The value of gravitational force should be taken as 10 m/s².

Neem die waarde van gravitasiekrag as 10 m/s².

9. All dimensions are in millimeters, unless stated otherwise in the question. Alle afmetings is in millimeter, tensy anders in die vraag aangedui.

10. A formula sheet is attached to the question paper. 'n Formuleblad vir jou gebruik is aan hierdie vraestel aangeheg.

11. Write neatly and legibly. Skryf netjies en leesbaar.

Question / Vraag

Content / Inhoud Marks / Punte

Time / Tyd (Minutes) / Minute

1 Safety (Generic) / Veiligheid (Generies) 8 8

2 Tools / Gereedskap 8 8

3 Entrepreneurship / Entrepreneurskap 4 4

TOTAL / TOTAAL 20 20

P a g e | 3

Mechanical Technology Grade 8 30/03/2021

Question / Vraag 1 – Safety / Veiligheid

1. What is the definition of an accident? (2) Wat is die definisie van ‘n ongeluk?

2. What do you understand by the term good housekeeping? Wat verstaan jy onder die term goeie bedryfshuishouding? (2)

3. Name at least FOUR basic items that must be in a first aid kit. Noem ten minste VIER basiese items wat in ‘n noodhulpkis moet wees. (4)

[8]

Question / Vraag 2 – Tools / Gereedskap

Picture / Prent Name / Naam

Use / Gebruik

2.1.

2.1.1 2.1.2

2.2

2.2.1 2.2.2

2.3

2.3.1 2.3.2

2.4

2.4.1 2.4.2

[8]

P a g e | 4

Mechanical Technology Grade 8 30/03/2021

Question / Vraag 3 – Entrepreneurship / Entrepreneurskap

3.1. What is the definition of Entrepreneurship? Wat is die definisie van Entrepreneurskap? (2)

3.2. With your current knowledge of the subject Mechanical Technology,

what products would you be able to produce to sell as an entrepreneur? Met jou huidige kennis van die vak Meganiese Tegnologie, waste produkte sal jy kan vervaardig en verkoop as ‘n entrepreneur. (2)

[4]